Mo-doped ZnV2O6/reduced graphene oxide photoanodes for solar hydrogen production

Construction of dual driving force in carbon nitride for highly efficient hydrogen evolution: Simultaneously manipulating carriers transport in intra- and interlayer

Photocatalytic hydrogen evolution is widely recognized as an environmentally friendly approach to address future energy crises and environmental issues. However, rapid recombination of photo-induced charges over carbon nitride in lateral and vertical direction hinder this process. Herein, we proposed an effective strategy involving the embedding of benzene rings and the intercalation of platinum atoms on carbon nitride for a controlled intralayer and interlayer charges flow. Modified carbon nitride exhibits a significant higher hydrogen evolution rate (6288.5 μmol/g/h), which is 42 times greater than that of pristine carbon nitride. Both experiments and simulations collectively indicate that the improved photocatalytic activities can be attributed to the adjustment of the highly symmetric structure of carbon nitride, achieved by embedding benzene rings to induce the formation of an intralayer build-in electric field and intercalating Pt atoms to enhance interlayer polarization, which simultaneously accelerate lateral and vertical charges migration. This dual-direction charges separation mechanism in carbon nitride provides valuable insights for the development of highly active photocatalysis.

Experimental and theoretical study of improved mesoporous titanium dioxide perovskite solar cell: The impact of modification with graphene oxide

The present study serves experimental and theoretical analyses in developing a hybrid advanced structure as a photolysis, which is based on electrospun Graphene Oxide-titanium dioxide (GO-TiO2) nanofibers as an electron transfer material (ETMs) functionalized for perovskite solar cell (PVSCs) with GO. The prepared ETMs were utilized for the synthesis of mixed-cation (FAPbI3)0.8(MAPbBr3)0.2. The effect of GO on TiO2 and their chemical structure, electronic and morphological characteristic were investigated and discussed. The elaborated device, namely ITO/Bl-TiO2/3 wt% GO-TiO2/(FAPbI3)0.8(MAPbBr3)0.2/spiro-MeTAD/Pt, displayed 20.14% disposition and conversion solar energy with fill factor (FF) of 1.176%, short circuit current density (Jsc) of 20.56 mA/cm2 and open circuit voltage (VOC) 0.912 V. The obtained efficiency is higher than titanium oxide (18.42%) and other prepared GO-TiO2 composite nanofibers based ETMs. The developed materials and device would facilitate elaboration of advanced functional materials and devices for energy storage applications.

Synthesis of active-site rich molybdenum-doped manganese tungstate nanocubes for effective electrochemical sensing of the antiviral drug (COVID-19) nitazoxanide

Nitazoxanide (NTZ), a promising antiviral agent, is currently being tested in clinical trials as a potential treatment for novel coronavirus disease 2019 (COVID -19). This paper describes a one-pot hydrothermal synthesis to prepare molybdenum (Mo)-doped manganese tungstate nanocubes (Mo-MnWO4 NCs) for the electrochemical sensing of NTZ. The as-prepared Mo-MnWO4 NCs were characterized using various techniques such as XRD, Raman, FE-SEM, FE-TEM, and XPS to confirm the crystal structure, morphology, and elemental composition. The obtained results demonstrate that Mo doping on MnWO4 generates many vacancy sites, exhibiting remarkable electrochemical activity. The kinetic parameters of the electrode modified with Mo-MnWO4 NCs were calculated to be (Ks) 1.1 × 10-2 cm2 s-1 and (α) 0.97, respectively. Moreover, a novel electrochemical sensor using Mo-MnWO4 NCs was fabricated to detect NTZ, which is used as a primary antibiotic to control COVID-19. Under optimal conditions, the electrochemical reduction of NTZ was determined with a low detection limit of 3.7 nM for a linear range of 0.014-170.2 μM with a high sensitivity of 0.78 μA μM-1 cm-2 and negligible interference with other nitro group-containing drugs, cations, and anions. The electrochemical sensor was successfully used to detect NTZ in the blood serum and urine samples and achieved high recoveries in the range of 94-99.2% and 95.3-99.6%, respectively. This work opens a way to develop high-performance sensing materials by exploring the introduction of defect engineering on metal tungstates to detect drug molecules for practical applications.

Photocatalytic nanocomposite membranes for environmental remediation

We report the design and one-pot synthesis of Ag-doped BiVO₄embedded in reduced graphene oxide (BiVO₄:Ag/rGO) nanocomposites via a hydrothermal processing route. The binary heterojunction photocatalysts exhibited high efficiency for visible light degradation of model dyes and were correspondingly used for the preparation of photocatalytic membranes using polyvinylidene fluoride (PVDF) or polyethylene glycol (PEG)-modified polyimide (PI), respectively. The surface and cross-section images combined with elemental mapping illustrated the effective distribution of the nanocomposites within the polymeric membranes. Photocatalytic degradation efficiencies of 61% and 70% were achieved after 5 h of visible light irradiation using BiVO₄:Ag/rGO@PVDF and BiVO₄:Ag/rGO@PI (PEG-modified) systems, respectively. The beneficial photocatalytic performance of the BiVO₄:Ag/rGO@PI (PEG-modified) membrane is explained by the higher hydrophilicity due to the PEG modification of the PI membrane. This work may provide a rational and effective strategy to fabricate highly efficient photocatalytic nanocomposite membranes with well-contacted interfaces for environmental purification.

Interface Engineered V-Zn Hybrids: Electrocatalytic and Photocatalytic CO2 Reductions

V-Zn hybrids have widely been used as catalyst materials in the environment and as energy. Herein, V-Zn hybrid electrodes were prepared by the hydrothermal and sputter-deposition methods using a Zn foil support. Their electrocatalytic CO₂ reduction (EC CO₂ RR) performances were tested under various applied potentials, different electrolytes, and concentrations before and after thermal treatment of the demonstrated electrode. Gas and liquid products were confirmed by gas chromatography and nuclear magnetic resonance spectroscopy, respectively. For V-Zn electrode by hydrothermal method produced mainly syngas (CO and H₂) with tunable ratio by varying applied potential. Minor products include CH₄, C₂H₄, and C₂H₆. A liquid product of formate showed a Faradaic efficiency (FE) of 2%. EC CO₂ RR efficiency for CO, CH₄, and formate was best in 0.2 M KHCO₃ electrolyte condition. CO and formate were further increased by photoirradiation and Nafion-treated electrode. Formate and CH₄ productions were significantly increased by thermal treatment of the V-Zn electrode. CO production was diminished for the V-Zn electrode by sputter deposition but was recovered by thermal treatment. Photocatalytic CO₂ RR was tested to find that RR products include CH₃OH, CO, CH₄, C₂H₄, and C₂H₆. Interestingly long-chain hydrocarbons (C_nH_2n and C_nH_2n+2, where n = 3-6) were first observed under mild conditions. The long-chain formation was understood by Fisher-Tropsch (F-T) synthesis. Alkenes were observed to be more produced than alkanes unlike in the conventional F-T synthesis. The present new findings provide useful clues for the development of hybrid electro-and photo-catalysts tested under various experimental conditions in energy and environment.