Recent innovative research on chromium (VI) adsorption mechanism

Controlled Primary Amine-Enriched SG-Bonded Papain Surface: Synthesis, Characterization, and Extraction of Protonated Dichromate

The single-step synthesis of nitro-derivatized SG using dimethyldichlorosilane in an aprotic solvent dichloromethane at 300 K is efficient and straightforward. Reduction and diazotization effectively functionalize the material for enzyme coupling at the O-carbon of the enzyme's tyrosine. The high extraction efficiency of protonated dichromate ions with a breakthrough capacity of 480 μmol·g-1 is notable. Eco-friendly elution using distilled water achieves a significant enrichment factor of 23.2. Excellent reusability (up to 900 cycles) and stable sorption efficiency (ζ ≥ 0.9) highlight the material's potential for practical applications and future research.

Fruit waste-derived cellulose-polyaniline composite for adsorption-coupled reduction of chromium oxyanions

Hexavalent chromium oxyanions, known as potentially toxic micropollutants, exist in the effluents and discharges of metallurgical, electroplating, refractory, chemical, and tanning industries. The exposure of chromium-contaminated water causes severe health hazards. The present work outlines a facile approach to grow polyaniline (PANI) on fruit-waste-derived cellulose (CEL) via oxidative polymerization of aniline; followed by chemical processing with NH4OH to obtain CEL-PANI-EB composites for adsorptive separation-coupled reduction of highly toxic hexavalent chromium oxyanions. The spectroscopic analyses of the CEL-PANI-EB composite before and after adsorption of Cr(VI) oxyanions revealed hydrogen bonding, electrostatic, and complexation as major interactive pathways. The adsorbed hexavalent chromium oxyanions are reduced into Cr(III) species by oxidation of PANI-based benzenoid amine into quinoid imine in the CEL-PANI-EB composite. The adsorption of Cr(VI) oxyanions by the CEL-PANI-EB composite showed negligible effects of other anionic co-pollutants, like NO3- and SO42-. The CEL-PANI-EB composite adsorbed Cr(VI) oxyanions with a removal capacity of 469 mg g-1, based on the Langmuir adsorption isotherm model. The hydroxyl functionalities in cellulose and amine/imine functionalities in PANI facilitate the electrostatic attraction between the CEL-PANI-EB and Cr(VI) oxyanions in an acidic environment beside the hydrogen linkages. The adsorbed Cr(VI) oxyanions are reduced to Cr(III)-based species by the benzenoid amines of PANI, as revealed from the XPS analyses. The CEL-PANI-EB composite showed excellent recyclability and maintained 83.4% adsorption efficiency after seven runs of chromium adsorption-desorption. The current findings reveal the potential of CEL-PANI-EB composites for the adsorptive removal of Cr(VI) oxyanions and their conversion into a lesser toxic form, making them promising materials for wastewater treatment applications.

Efficient removal of Cr(VI) contaminant using recoverable silica from volcanic ash as natural adsorbent: Synthesis and activity in the mechanism and kinetic adsorption

Modification of silica purified from the Merapi volcanic ash with magnetic material of Fe3O4 and attachment of cetyl triamine bromide (CTA-Br) on the magnetic cored has been performed to provide recoverable and positive surfaced of natural adsorbent. The magnetic cored was prepared via co-precipitation and CTA-Br attachment was conducted by a facile strategy. Then, the modified adsorbents were characterized by SEM, TEM, XRD, and FTIR instruments and examined for removing anionic Cr(VI) from the water media. The characterization data confirmed that crystals of Fe3O4 coated by SiO2 that has been bound with CTA-Br have been successfully formed. Additionally, increasing CTA-Br loaded gives thicker lamination on Fe3O4@SiO2/CTA-Br, but the CTA-Br loaded with higher than 0.25 mmol, leads to the coating peeled out. It is also demonstrated that Fe3O4@SiO2/CTA-Br prepared with CTA-Br 0.25 mmol is ideal for Cr(VI) anionic removal, regarding to the highest adsorption and very good separation or recovery process. Moreover, the optimal dose of Fe3O4@SiO2/CTA-Br in the Cr(VI) removal was observed at 0.25 g/20 mL under condition of pH 3 for 60 min. The adsorption of Cr(VI) well fits the Langmuir isotherm model with an adsorption capacity of 3.38 mg g-1 and is in a good agreement with pseudo-second order giving kinetic constant at 0.005 g mg-1 min-1. Thus, it is clear that the natural adsorbent material with recoverable properties for more efficient and wider application of removal Cr(VI) contaminant was expected from this study.

Synthesis and characterization of iron oxide-commercial activated carbon nanocomposite for removal of hexavalent chromium (Cr6+) ions and Mordant Violet 40 (MV40) dye

Iron Oxide-commercial activated carbon nanocomposite (CAC-IO) was prepared from commercial activated carbon (CAC) by the co-precipitation method, and the resulting nanocomposite was used as an adsorbent to remove hexavalent chromium (Cr6+) ions and Mordant Violet 40 (MV40) dye from wastewater. The produced materials (CAC, CAC after oxidation, and CAC-IO) were comparatively characterized using FTIR, BET, SEM, EDX TEM, VSM, and XRD techniques. The adsorption mechanism of Cr6+ ions and MV40 dye on CAC-IO was examined using Langmuir and Freundlich isotherm models.. Different models were applied to know the adsorption mechanism and it was obtained that Pseudo-second order fits the experimental data better. This means that the adsorption of the adsorbate on the nanocomposite was chemisorption. The maximum removal percent of Cr6+ ions by CAC-IO nanocomposite was 98.6% determined as 2 g L-1 adsorbent concentration, 100 mg L-1 initial pollutant concentration, solution pH = 1.6, the contact time was 3 h and the temperature was room temperature. The maximum removal percentage of Mordant Violet 40 dye (C.I. 14,745) from its solutions by CAC-IO nanocomposite was 99.92% in 100 mg L-1 of initial dye concentrations, 1.0 g L-1 of adsorbent concentration, solution pH = 2.07, the contact time was 3 h. The MV40 dye adsorption on CAC-IO was the most fitted to the Freundlich isotherm model. The maximum adsorption capacity was calculated according to the Langmuir model as 833.3 mg g-1 at 2 g L-1 of adsorbent concentration and 400 mg L-1 of initial MV40 dye concentration. The Cr6+ ions adsorption on CAC-IO was more fitted to the Freundlich model with Qmax, equal to 312.50 mg g-1 at 1 g L-1 adsorbent concentration and 400 mg L-1 of Cr6+ ions initial concentrations.

Fabrication of Iron-Containing Biochar by One-Step Ball Milling for Cr(VI) and Tetracycline Removal from Wastewater

Simple ball milling technology can simultaneously improve the adsorption performance of adsorbents for heavy metals and organic pollutants and has attracted increasing attention. Iron-modified biochar (Fe@MBC) was prepared by one-step ball milling, and the characterization results proved that FeCl3 was successfully loaded on biochar. The removal rates of Cr(VI) and tetracycline hydrochloride (TC) by Fe@MBC were increased by 88.27% and 82.64% compared with BC. The average pore size, oxygen-containing functional groups and graphitization degree of Fe@MBC are higher than those of BC, which is more conducive to promoting adsorption. The adsorption isotherms show that the adsorption of Cr(VI) and TC on the Fe@MBC surface conforms to the Langmuir type of single-layer adsorption and the Freundlich model of multilayer adsorption, respectively. The maximum adsorption capacities of Cr(VI) and TC are 25.46 and 66.91 mg·g-1, respectively. Kinetic experiments show that the adsorption process is more consistent with the pseudo-second-order model of chemical adsorption. The adsorption process of Cr(VI) and TC on the Fe@MBC surface is a spontaneous endothermic process that becomes more obvious as the temperature increases. The increase in solution pH has a significant impact on the removal rate of Fe@MBC. When the pH value increased from 3 to 11, the adsorption rates decreased by 53.74% and 17.16%, respectively. The presence of PO43-, CO32-, K+, and Cu2+ significantly affects the adsorption of TC by Fe@MBC, and PO43- and CO32- also affect the adsorption of Cr(VI). Mechanistic studies show that ion exchange, electrostatic interaction, pore filling, and hydrogen bonding contribute to the removal of Cr(VI) and TC by Fe@MBC. The removal mechanism of Cr(VI) also involves complexation and redox reactions, and the removal mechanism of TC involves π-π bonds and van der Waals forces. The results show that Fe@MBC is a green and efficient adsorbent.

Removal of cationic and anionic toxic pollutants from simulated solutions using Sterculia foetida pod (SFP): equilibrium isotherm, kinetics, and characterization

The present work explores the sorption performance of Sterculia foetida pod (SFP) for the removal of methylene blue (MB) and chromium (Cr6+) from simulated solutions separately. The material characteristics namely textural analysis (specific surface area: 2.45 m2/g), morphological behavior (heterogeneous morphology containing pores and cavities), functional analysis (COO- stretching, C-O-C stretching vibrations, and -OH stretching) and thermal behavior (279.4 °C) were examined by various analytical techniques namely BET, SEM, FTIR, and TGA. Using non-linear Langmuir isotherm analysis, the maximal sorption capacity of SFP for the removal of MB and Cr6+ was predicted to be 74.1 mg/g and 27.3 mg/g, respectively. The optimized condition for sorption of MB and Cr6+ onto SFP was: dosage: 0.07 mg/L, initial pH: 7 (MB), and 2 (Cr6+). Thermodynamic data analysis confirmed the endothermic, favorable, spontaneous, and physisorption nature of sorption. The SFP has shown significant regeneration capacity in the consecutive runs (MB: 92.5% removal till 5th trial; Cr6+: 97.6% removal till 3rd trial). Based on these findings, SFP is a promising low-cost and eco-friendly candidate for the removal of anionic and cationic toxic pollutants in the absence of energy and chemical expenditure.NOVELTY STATEMENTSterculia foetida pod (SFP) explored for the removal of anionic and cationic toxic pollutants in the absence of energy and chemical expenditure.Mechanism for the interaction between toxic pollutants and SFP was predicted.Better sorption capacity (MB: 74.1 mg/g; Cr6+: 27.8 mg/g) and better regeneration capacity (MB: 92.5% for 5th trial; Cr6+: 97.6% for 3rd trial) was achieved.A feasible and spontaneous nature of sorption process toward the removal of MB and Cr6+ was demonstrated using thermodynamic relations.

A review of novel green adsorbents as a sustainable alternative for the remediation of chromium (VI) from water environments

The presence of heavy metal, chromium (VI), in water environments leads to various diseases in humans, such as cancer, lung tumors, and allergies. This review comparatively examines the use of several adsorbents, such as biosorbents, activated carbon, nanocomposites, and polyaniline (PANI), in terms of the operational parameters (initial chromium (VI) concentration (C_o), temperature (T), pH, contact time (t), and adsorbent dosage) to achieve the Langmuir's maximum adsorption capacity (q_m) for chromium (VI) adsorption. The study finds that the use of biosorbents (fruit bio-composite, fungus, leave, and oak bark char), activated carbons (HCl-treated dry fruit waste, polyethyleneimine (PEI) and potassium hydroxide (KOH) PEI-KOH alkali-treated rice waste-derived biochar, and KOH/hydrochloric acid (HCl) acid/base-treated commercial), iron-based nanocomposites, magnetic manganese-multiwalled carbon nanotubes nanocomposites, copper-based nanocomposites, graphene oxide functionalized amino acid, and PANI functionalized transition metal are effective in achieving high Langmuir's maximum adsorption capacity (q_m) for chromium (VI) adsorption, and that operational parameters such as initial concentration, temperature, pH, contact time, and adsorbent dosage significantly affect the Langmuir's maximum adsorption capacity (q_m). Magnetic graphene oxide functionalized amino acid showed the highest experimental and pseudo-second-order kinetic model equilibrium adsorption capacities. The iron oxide functionalized calcium carbonate (IO@CaCO₃) nanocomposites showed the highest heterogeneous adsorption capacity. Additionally, Syzygium cumini bark biosorbent is highly effective in treating tannery industrial wastewater with high levels of chromium (VI).

Structural Properties of Graphene Oxide Prepared from Graphite by Three Different Methods and the Effect on Removal of Cr(VI) from Aqueous Solution

Herein, three types of graphene oxides (GOs, GO-M1, GO-M2 and GO-M3) have been successfully prepared from graphite by three different methods and utilized for the removal of Cr(VI) from aqueous solutions. Further, the effects of initial concentration and pH, adsorbent dosage, contact time and temperature on the adsorption performance of GOs were investigated by batch adsorption experiments. Furthermore, the adsorption mechanisms for Cr(VI) adsorption by GOs are mainly the redox reaction and electrostatic attraction, while there are also pore filling, ion exchange and complexation involved in these adsorption processes. The adsorption kinetic and isotherm data indicate that these adsorption processes of GOs on Cr(VI) are dominantly monolayer chemisorption and equilibrium can be reached in 30 min. The saturation adsorption capacities (Qm, 298.15 K) of GO-M1, GO-M2 and GO-M3 for Cr(VI) are estimated to be 3.5412 mg⋅g-1, 2.3631 mg⋅g-1 and 7.0358 mg⋅g-1, respectively. Moreover, the adsorption thermodynamic study showed that these adsorption processes of Cr(VI) by the three types of GOs at 298.15 K to 323.15 K are endothermic, entropy-driven and thermodynamically spontaneous and feasible. Overall, these findings provided vital insights into the mechanism and application of Cr(VI) removal by GOs.

The Adsorption Potential of Cr from Water by ZnO Nanoparticles Synthesized by Azolla pinnata

Aqueous solutions containing toxic elements (TEs) (such as hexavalent chromium (Cr (VI)) can be toxic to humans even at trace levels. Thus, removing TEs from the aqueous environment is essential for the protection of biodiversity, hydrosphere ecosystems, and humans. For plant fabrication of zinc oxide nanoparticles (PF-ZnONPs), Azolla pinnata plants were used, and X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), SEM, and FTIR techniques were used for the identification of PF-ZnONPs and ZnONPs, which were used to remove Cr (VI) from aqueous solution. A number of adsorption parameters were studied, including pH, dose, concentration of metal ions, and contact time. The removal efficiency of PF-ZnONPs for Cr (VI) has been found to be 96% at a time (60 min), 69.02% at pH 4, and 70.43% at a dose (10 mg·L⁻¹). It was found that the pseudo-second-order model best described the adsorption of Cr (VI) onto PF-ZnONPs, indicating a fast initial adsorption via diffusion. The experimental data were also highly consistent with the Langmuir isotherm model calculations.

Modeling of Hexavalent Chromium Removal with Hydrophobically Modified Cellulose Nanofibers

Cellulose nanofibers (CNF) are sustainable nanomaterials, obtained by the mechanical disintegration of cellulose, whose properties make them an interesting adsorbent material due to their high specific area and active groups. CNF are easily functionalized to optimize the performance for different uses. The hypothesis of this work is that hydrophobization can be used to improve their ability as adsorbents. Therefore, hydrophobic CNF was applied to adsorb hexavalent chromium from wastewater. CNF was synthetized by TEMPO-mediated oxidation, followed by mechanical disintegration. Hydrophobization was performed using methyl trimetoxysilane (MTMS) as a hydrophobic coating agent. The adsorption treatment of hexavalent chromium with hydrophobic CNF was optimized by studying the influence of contact time, MTMS dosage (0-3 mmol·g^-1 CNF), initial pH of the wastewater (3-9), initial chromium concentration (0.10-50 mg·L^-1), and adsorbent dosage (250-1000 mg CNF·L^-1). Furthermore, the corresponding adsorption mechanism was identified. Complete adsorption of hexavalent chromium was achieved with CNF hydrophobized with 1.5 mmol MTMS·g^-1 CNF with the faster adsorption kinetic, which proved the initial hypothesis that hydrophobic CNF improves the adsorption capacity of hydrophilic CNF. The optimal adsorption conditions were pH 3 and the adsorbent dosage was over 500 mg·L^-1. The maximum removal was found for the initial concentrations of hexavalent chromium below 1 mg·L^-1 and a maximum adsorption capacity of 70.38 mg·g^-1 was achieved. The kinetic study revealed that pseudo-second order kinetics was the best fitting model at a low concentration while the intraparticle diffusion model fit better for higher concentrations, describing a multi-step mechanism of hexavalent chromium onto the adsorbent surface. The Freundlich isotherm was the best adjustment model.

Synthesis of Iron Nanomaterials for Environmental Applications from Hydrometallurgical Liquors

Hydrometallurgical leaching solutions are often rich in iron, which was traditionally considered a major impurity. However, iron can be selectively separated and recovered by applying appropriate solvent extraction and stripping techniques, and the resulting solutions can be valorized for the synthesis of high-added-value products, such as magnetic iron oxide nanoparticles (mIONPs). The aim of this study was to synthesize high-quality mIONPs from solutions simulating the composition of two alternative stripping processes. The precursor solutions consisted of Fe(II) in an acidic sulfate environment and Fe(III) in an acidic chloride medium. The Fe(II)-SO4 solution was treated with a mixture of KNO3-KOH reagents, and the product (M(II)) was identified as pure magnetite with a high specific magnetization of 95 emu·g−1. The treatment of Fe(III)-Cl solution involved the partial reduction of Fe(III) using metallic iron and the co-precipitation of iron cations with base addition combined with microwave-assisted heating. The product (M(III)) was a powder, which consisted of two phases, e.g., maghemite (75%) and magnetite (25%), and also had a high magnetic saturation of 80 emu·g−1. The nanopowders were evaluated for their effectiveness in removing Cr(VI) from contaminated waters. The maximum adsorption capacity was found to be equal to 11.4 and 17.4 mg/g for M(II) and M(III), respectively. The magnetic nanopowders could be easily separated from treated waters, a property that makes them promising materials for the water treatment sector.

Nitrate Removal by Zero-Valent Metals: A Comprehensive Review

Nitrate is a widespread water contaminant that can pose environmental and health risks. Various conventional techniques can be applied for the removal of nitrate from water and wastewater, such as biological denitrification, ion exchange, nanofiltration, and reverse osmosis. Compared to traditional methods, the chemical denitrification through zero-valent metals offers various advantages, such as lower costs, simplicity of management, and high efficiencies. The most utilized material for chemical denitrification is zero-valent iron (ZVI). Aluminium (ZVA), magnesium (ZVM), copper (ZVC), and zinc (ZVZ) are alternative zero-valent metals that are studied for the removal of nitrate from water as well as from aqueous solutions. To the best of our knowledge, a comprehensive work on the use of the various zero-valent materials that are employed for the removal of nitrate is still missing. Therefore, in the present review, the most recent papers concerning the use of zero-valent materials for chemical denitrification were analysed. The studies that dealt with zero-valent iron were discussed by considering microscopic (mZVI) and nanoscopic (nZVI) forms. For each Fe0 form, the effects of the initial pH, the presence or absence of dissolved oxygen, the initial nitrate concentration, the temperature, and the dissolved ions on the nitrate removal process were separately evaluated. Finally, the different materials that were employed as support for the nanoparticles were examined. For the other zero-valent metals tested, a detailed description of the works present in the literature was carried out. A comparison of the various features that are related to each considered material was also made.

The application of GO-Fe3O4 nanocomposite for chromium adsorption from tannery industry wastewater

The discharge of untreated tannery industrial wastewater into the environment has resulted in an adverse effect on the ecosystem and public health. Therefore, this work aimed to remove chromium ions from tannery wastewater through magnetite graphene oxide-nanocomposite (GO-Fe₃O₄). The experimental design of the study was a full factorial 2⁴ approach using pH, adsorbent dose, contact time, and initial chromium concentrations. The results of FTIR analysis revealed the presence of functional groups such as hydroxyl (3438 cm^-1), alcohol (1230 cm^-1), aromatic (1467 cm^-1), ketone (1629 cm^-1), and ether (1120 cm^-1). Similarly, GO-Fe₃O₄ acquired a high surface area of 296.2 m²/g whereas the XRD analysis showed the presence of predominant peaks which are attributed to the magnetite component. Moreover, the SEM image showed many ups and downs on the surface of the adsorbent. These cracks of morphology can create a conducive environment for the interaction of adsorbent and adsorbate. The maximum chromium removal of 95.9% was achieved at the optimum conditions of the initial chromium concentration of 40 mg/L, pH 4, adsorbent dose 1 g/100 mL, and contact time of 120 min whereas the removal of chromium from real tannery wastewater was found to be 90.3%. Based on the adsorption isotherm, the Langmuir model was the best fit for experimental data at R² 0.99, indicating homogeneous and monolayer adsorption. Finally, it can be concluded that GO-Fe₃O₄ was effective for chromium removal, which is a promising technology to be scaled up at the industrial level for wastewater treatment.

Screening of rice cultivars for Cr-stress response by using the parameters of seed germination, morpho-physiological and antioxidant analysis

Rice is the most important crop for the majority of population across the world with sensitive behavior toward heavy metals such as chromium (Cr) in polluted regions. Although, there is no information on the Cr resistance phenotyping in rice. Herein, two different groups of rice cultivars (normal, and hybrid) were used, each group with 14 different rice cultivars. Firstly, seed germination analysis was conducted by evaluating various seed germination indices to identify the rice cultivars with greatest seed germination vigor. Furthermore, exposure of chromium (Cr) toxicity to 28 different rice varieties (NV1-NV14, HV1-HV14) caused noticeable plant biomass reduction. Subsequently, NV2, NV6, NV10, NV12, NV13 (normal type), HV1, HV4, HV8, and HV9 (hybrid types) were pragmatic as moderately sensitive varieties, while NV3, NV4, NV9, and NV14 (normal type), HV3, HV6, HV7, and HV13 were observed as moderately tolerant. Although, NV7, and HV10 were ranked most sensitive cultivars, and NV11, and HV14 were considered as most tolerant varieties as compared to the other rice (both groups) genotypes. Afterward, Cr induced reduction in chlorophyll pigments were significantly lesser in HV14 relative to NV11, NV7, and especially HV10, and as a result HV14 modulated the total soluble sugar level as well as reduced ROS accumulation, and MDA contents production by stimulating the antioxidant defense mechanism conspicuously which further reduced the electrolyte leakage as well. Our outcomes provide support to explore the Cr tolerance mechanism in cereal crops as well as knowledge about rice breeding with increased tolerance against Cr stress.

Nano-Porous Composites of Activated Carbon–Metal Organic Frameworks (Fe-BDC@AC) for Rapid Removal of Cr (VI): Synthesis, Adsorption, Mechanism, and Kinetics Studies

Metal–organic frameworks (MOFs) are a group of porous materials that display potential in the elimination of toxic industrial compounds (TICs) from polluted water streams. However, their applications have so far been held up by issues due to their physical nature and cost. In this study, activated carbon (AC) is modified with an Fe-based MOF, iron terephthalate (Fe-BDC). A facile and cost-effective impregnation method is used for enhanced removal from aqueous solutions. The new adsorbent is characterized by SEM, FTIR, PXRD, and BET. The composite displays excellent uptake of Cr (VI) when compared to un-impregnated AC with a maximum monolayer adsorption capacity of 100 mg·g−1. The experimental data shows a high correlation to the Langmuir adsorption model. The adsorption kinetic study reveals that the adsorption of Cr (VI) to Fe-BDC@AC obeys the pseudo-first-order equation. The composite shows high reusability after five cycles and high adsorption rates reaching equilibrium in just 50 min. Such properties make the nanocomposite promising for water decontamination on larger scales compared to powder-based alternatives, such as individual MOF crystals.

Modelling and optimization of hexavalent chromium removal from aqueous solution by adsorption on low-cost agricultural waste biomass using response surface methodological approach

In this study, a response surface methodology (RSM) approach using central composite design (CCD) was investigated to develop a mathematical model and to optimize the effects of pH, adsorbent amount and temperature related to the hexavalent chromium removal by biosorption on peanut shells (PSh). The highest removal percentage of 30.28% was found by the predicted model under the optimum conditions (pH of 2.11, 0.73 g of PSh and 37.2 °C) for a 100 mg/L initial Cr(VI) concentration, which was very near to the experimental value (29.92%). The PSh was characterized by SEM, EDX, FTIR, BET, XRD analyses. Moreover, a Langmuir isotherm fitted well (R² = 0.992) with the experimental data, and the maximum adsorption capacity was discovered to be 2.48 and 3.49 mg/g respectively at 25 and 45 °C. Kinetic data were well foreseen by pseudo second order. Thermodynamic study depicted that biosorption of Cr(VI) onto PSh was spontaneous and endothermic. Regeneration of the PSh using NaOH showed a loss <5% in the Cr(VI) removal efficiency up to three recycle runs. In summary, the Cr(VI) removal onto economic, sensitive and selective biosorbent (PSh) was optimized using CCD to study biosorption behaviors.

Enhanced aqueous Cr(VI) removal using chitosan-modified magnetic biochars derived from bamboo residues

The purpose of this study was to fabricate a chitosan modified magnetic bamboo biochar (CMBB) for Cr(VI) detoxification from aqueous solution. Results showed that chitosan modification provided more active adsorption sites on the surface of magnetic bamboo biochar (MBB), and hence enhanced Cr(VI) removal from aqueous solution. The maximum adsorption capacities of MBB and CMBB for Cr(VI) at 25 °C were 75.8 and 127 mg g^-1, respectively. Increasing solution pH inbibited Cr(VI) adsorption by adsorbents. However, CMBB maintained a high Cr(VI) removal efficiencies over a broader pH range (2-10), and could attain 36% of the maximum adsorption (40 mg g^-1) even at a high pH of 10.0. Rising temperature enhanced the Cr(VI) removal by two adsorbents. The escalating ionic strength and coexist substances, including Na⁺, Ca²⁺, Fe³⁺, Cl^-, SO₄^2-, PO₄^3- and humate, inhibited the adsorption efficiency of Cr(VI) on adsorbents. After the fifth adsorption-desorption cycle, the adsorption efficiencies of CMBB and MBB for Cr(VI) remained above 90% and less than 50%, respectively. All these results indicated that CMBB could be a practical adsorbent that can be utilized for the detoxification of Cr(VI) ions from wastewater.

A review of chromite mining in Sukinda Valley of India: impact and potential remediation measures

Sukinda Valley, one of the highly polluted areas of the world is generating tons of mining waste and causing serious health and environmental issues in its surroundings. Several reports are available reporting the severity of hexavalent chromium, yet little efforts have been made to address the pollution and its remediation due to a lack of proper remedial measures. The review highlights the pros and cons of various physical, chemical and biological techniques used worldwide for the treatment of chromium waste and also suggests better and reliable bioremediation measures. Microbes such as Acidophilium and Acidithiobacillus caldus (Bioleaching), Pseudomonas, Micrococcus and Bacillus (Bioreduction), Aereobacterium and Saccharomyces (Biosorption), are widely used for bioremediation of hexavalent chromium owing to their unique metabolic activities, ionic movement through an extracellular membrane, and other cellular adsorptions and reduction properties. The use of native and hybrid combinations of microbes supported by organic supplements is projected as a fast and efficient technique that not only reduces chromium quantity but also maintains the integrity of the microbial sources. Innovation and emphasis on nano-based products like nanocomposite, nano adsorbent, nanoscale zerovalent iron (nZVI) particles and multifunctional plant-growth-promoting bacteria (PGPB) will serve as the next generation environmental remediation technologies in the near future.

Adsorption of hexavalent chromium using modified walnut shell from solution

Modified walnut shell (MWS) was obtained using diethylenetriamine through a grafting reaction and its adsorption capacity toward Cr(VI) was enhanced. The adsorbent was characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), and elemental analysis and the results showed that the modification was effective. To optimize experimental conditions, the effect of temperature, solution pH, salinity, contact time, and Cr(VI) concentration on adsorption quantity were performed in batch mode. It showed that the adsorption ability for Cr(VI) onto MWH can reach 50.1 mg·g^-1 at 303 K with solution pH 3. Both the solution pH and salinity had a great impact on the adsorption capacity. The Langmuir model can predict the equilibrium process while the pseudo-second-order model can describe the kinetic process. The Yan model can be used to predict the column process. Additionally, there was also some regeneration ability for Cr-loaded MWH. Consequently, MWS is effective for removing Cr(VI) from solution.