Surface modification of polylactic acid (PLA) by air atmospheric plasma treatment

Alkaline etching assisted polydopamine coating for enhanced cell-material interactions on 3D printed polylactic acid scaffolds

The implant surface chemistry and topography are primary factors regulating the success and survival of bone scaffold. Surface modification is a promising alternative to enhance the biocompatibility and tissue response to augment the osteogenic functionalities of polyesters like PLA. The study employed the synergistic effect of alkaline hydrolysis and polydopamine (PDA) functionalization to enhance the cell-material interactions on 3D printed polylactic acid (PLA) scaffold. Comprehensive characterization of the modified PLA highlights the improvements in the physical, chemical and cell-material interactions upon two-step surface modification. The X-ray photoelectron spectroscopy (XPS) analysis substantiated enhanced PDA deposition with a ∼8.2% increase in surface N composition after surface etching due to homogeneous PDA deposition compared to the non-etched counterpart. The changes in surface chemistry and morphology upon dual surface modification complemented the human osteoblast (HOS) attachment and proliferation, with distinct cell morphology and spreading on PDA coated etched PLA (Et-PLAPDA) scaffolds. Moreover, substantial improvement in osteogenic differentiation of UMR-106 cells on etched PLA (Et-PLA) and Et-PLAPDA highlights the suitability of alkali etching-mediated PDA deposition to improve mineralization on PLA. Overall, the present work opens insights to modify scaffold surface composition, topography, hydrophilicity and roughness to regulate local cell adhesion to improve the osteogenic potential of PLA.

Highly Porous 3D Nanofibrous Scaffold of Polylactic Acid/Polyethylene Glycol/Calcium Phosphate for Bone Regeneration by a Two-Step Solution Blow Spinning (SBS) Facile Route

This work presents the successful production of highly porous 3D nanofibrous hybrid scaffolds of polylactic acid (PLA)/polyethylene glycol (PEG) blends with the incorporation of calcium phosphate (CaP) bioceramics by a facile two-step process using the solution blow spinning (SBS) technique. CaP nanofibers were obtained at two calcium/phosphorus (Ca/P) ratios, 1.67 and 1.1, by SBS and calcination at 1000 °C. They were incorporated in PLA/PEG blends by SBS at 10 and 20 wt% to form 3D hybrid cotton-wool-like scaffolds. Morphological analysis showed that the fibrous scaffolds obtained had a randomly interconnected and highly porous structure. Also, the mean fiber diameter ranged from 408 ± 141 nm to 893 ± 496 nm. Apatite deposited considerably within 14 days in a simulated body fluid (SBF) test for hybrid scaffolds containing a mix of hydroxyapatite (HAp) and tri-calcium phosphate-β (β-TCP) phases. The scaffolds with 20 wt% CaP and a Ca/P ration of 1.1 showed better in vitro bioactivity to induce calcium mineralization for bone regeneration. Cellular tests evidenced that the developed scaffolds can support the osteogenic differentiation and proliferation of pre-osteoblastic MC3T3-E1 cells into mature osteoblasts. The results showed that the developed 3D scaffolds have potential applications for bone tissue engineering.

Development of Functionalized Polylactide Thin Films Using Poly(methylhydrogenosiloxane) Sol-Gel Process with Improved Antifouling Properties

Biobased polylactide (PLA) films were modified with low reticulate polysiloxane gel acting as a scalable platform for the hydrophilization of polymeric film surface. The PLA thin film was first coated with poly(methylhydrogenosiloxane) (PMHS) by the sol-gel transition via the condensation of diethoxymethylsilane (DH) and triethoxysilane (TH) using trifluoromethanesulfonic acid as a catalyst. Then, hydrosilylation of Si-H bonds in the presence of Karstedt's catalyst allowed the covalent grafting of hydrophilic alkene-containing molecules, i.e., triethylene glycol monomethyl allyl (TEGMEA) and a new zwitterionic allylcarboxybetaine (ACB) synthesized for the first time by the quaternization of dimethyl allyl amine (DMAA) with β-propiolactone. PMHS coating on the PLA film was evidenced by Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The observation by atomic force microscopy (AFM) revealed a homogeneous coating with low roughness (RMS = 0.29 nm). The hydrophilicity of functionalized PLA films was determined by water contact angle (WCA) measurements using the captive bubble method. A large increase in wettability properties was observed for both grafting with TEGMEA (WCA = 38°) and ACB (WCA = 42°) in comparison with the native PLA film (WCA = 80°). Moreover, the biocompatibility and antifouling efficiency of functionalized PLA films were evaluated by protein adsorption, bacterial adhesion, and cytotoxicity tests. The results indicate that the grafting of the two types of hydrophilic compounds does not affect the biocompatibility of PLA while significantly reducing protein adsorption and bacterial adhesion, thus showing the great potential of this surface functionalization strategy for applications in the medical field.

The Deposition of Hydroxyapatite Particles Within an Organic Matrix on the Surface of Poly(lactic acid)

Hydroxyapatite (HAP) is a well-established material in biomedical applications, especially for bone tissue regeneration, dental implants, and drug delivery systems. Recent research emphasizes enhancing the biocompatibility and osteoconductivity of orthopedic implants using HAP. This study explores the potential of combining HAP with a lipid matrix to improve the surface properties and biocompatibility of poly(lactic acid) (PLA)-based, 3D-printed, resorbable bone implants. We utilized the Langmuir-Blodgett method to deposit HAP within a dihexadecyl phosphate (DHP) matrix onto PLA substrates. This study demonstrates that DHP and HAP form stable monolayers at the air/water interface with HAP particles distributed within a homogeneous lipid matrix. The presence of HAP and the resulting changes in surface free energy (SFE) are hypothesized to enhance the biocompatibility of PLA implants. Our findings indicate that films composed of DHP + HAP 5:1 are particularly effective in altering PLA surface characteristics, potentially improving osteointegration, and reducing microbial adherence. Overall, this work highlights that surface modification of PLA with HAP and lipid matrices is the first step towards new, promising, and cost-effective strategies for developing advanced biomaterials for bone regeneration.

Recent approaches in the application of antimicrobial peptides in food preservation

Antimicrobial peptides (AMPs) are small peptides existing in nature as an important part of the innate immune system in various organisms. Notably, the AMPs exhibit inhibitory effects against a wide spectrum of pathogens, showcasing potential applications in different fields such as food, agriculture, medicine. This review explores the application of AMPs in the food industry, emphasizing their crucial role in enhancing the safety and shelf life of food and how they offer a viable substitute for chemical preservatives with their biocompatible and natural attributes. It provides an overview of the recent advancements, ranging from conventional approaches of using natural AMPs derived from bacteria or other sources to the biocomputational design and usage of synthetic AMPs for food preservation. Recent innovations such as structural modifications of AMPs to improve safety and suitability as food preservatives have been discussed. Furthermore, the active packaging and creative fabrication strategies such as nano-formulation, biopolymeric peptides and casting films, for optimizing the efficacy and stability of these peptides in food systems are summarized. The overall focus is on the spectrum of applications, with special attention to potential challenges in the usage of AMPs in the food industry and strategies for their mitigation.

The effect of Dunaliella salina extracts on the adhesion of Pseudomonas aeruginosa to 3D printed polyethylene terephthalate and polylactic acid

Polyethylene terephthalate (PET) and polylactic acid (PLA) are among the polymers used in the food industry. In this study, crude extracts of Dunaliella salina were used to treat the surface of 3D printed materials studied, aiming to provide them with an anti-adhesive property against Pseudomonas aeruginosa. The hydrophobicity of treated and untreated surfaces was characterized using the contact angle method. Furthermore, the adhesive behavior of P. aeruginosa toward the substrata surfaces was also studied theoretically and experimentally. The results showed that the untreated PLA was hydrophobic, while the untreated PET was hydrophilic. It was also found that the treated materials became hydrophilic and electron-donating. The total energy of adhesion revealed that P. aeruginosa adhesion was theoretically favorable on untreated materials, while it was unfavorable on treated ones. Moreover, the experimental data proved that the adhesion to untreated substrata was obtained, while there was complete inhibition of adhesion to treated surfaces.

The preparation, resources, applications, and future trends of nanofibers in active food packaging: a review

Active packaging is a novel strategy for maintaining the shelf life of products and ensuring their safety, freshness, and integrity that has emerged with the consumer demand for safer, healthier, and higher quality food. Nanofibers have received a lot of attention for the application in active food packaging due to their high specific surface area, high porosity, and high loading capacity of active substances. Three common methods (electrospinning, solution blow spinning, and centrifugal spinning) for the preparation of nanofibers in active food packaging and their influencing parameters are presented, and advantages and disadvantages between these methods are compared. The main natural and synthetic polymeric substrate materials for the nanofiber preparation are discussed; and the application of nanofibers in active packaging is elaborated. The current limitations and future trends are also discussed. There have been many studies on the preparation of nanofibers using substrate materials from different sources for active food packaging. However, most of these studies are still in the laboratory research stage. Solving the issues of preparation efficiency and cost of nanofibers is the key to their application in commercial food packaging.

Incorporation of Nano-Zinc Oxide as a Strategy to Improve the Barrier Properties of Biopolymer-Suberinic Acid Residues Films: A Preliminary Study

Finishing coatings in the wood-based composites industry not only influence the final appearance of the product but also serve to protect against fungi and molds and reduce the release of harmful substances, particularly formaldehyde and volatile organic compounds (VOCs). Carbon-rich materials, such as those derived from birch bark extraction, specifically suberin acids, can fulfill this role. Previous research has demonstrated that adding suberin acid residues (SAR) at 20% and 50% by weight significantly enhances the gas barrier properties of surface-finishing materials based on poly(lactide) (PLA) and polycaprolactone (PCL), particularly in terms of total VOC (TVOC) and formaldehyde emissions. This study aims to explore whether these properties can be further improved through the incorporation of nano-zinc oxide (nano-ZnO). Previous research has shown that these nanoparticles possess strong resistance to biological factors and can positively affect the characteristics of nanofilms applied as surface protection. The study employed PLA and PCL finishing layers blended with SAR powder at 10% w/w and included 2% and 4% nano-zinc oxide nanoparticles. The resulting blends were milled to create a powder, which was subsequently pressed into 1 mm-thick films. These films were then applied to raw particleboard surfaces. TVOC and formaldehyde emission tests were conducted. Additionally, the fungal resistance of the coated surfaces was assessed. The results showed that PLA/SAR and PCL/SAR composites with the addition of nano-zinc oxide nanoparticles exhibited significantly improved barrier properties, offering a promising avenue for developing biodegradable, formaldehyde-free coatings with enhanced features in the furniture industry. Furthermore, by utilizing SAR as a post-extraction residue, this project aligns perfectly with the concept of upcycling.

3D-printed electrodes using graphite/carbon nitride/polylactic acid composite material: A greener platform for detection of amaranth dye in food samples

The production of sustainable materials with properties aimed at the additive manufacturing of electrochemical sensors has gained prestige in the scientific scenario. Here, a novel lab-made composite material using graphite (G) and carbon nitride (C3N4) embedded into polylactic acid (PLA) biopolymer is proposed to produce 3D-printed electrodes. PLA offers printability and mechanical stability in this composition, while G and C3N4 provide electrical properties and electrocatalytic sites, respectively. Characterizations by Raman and infrared spectroscopies and Energy Dispersive X-rays indicated that the G/C3N4/PLA composite was successfully obtained, while electron microscopy images revealed non-homogeneous rough surfaces. Better electrochemical properties were achieved when the G/C3N4/PLA proportion (35:5:60) was used. As a proof of concept, amaranth (AMR), a synthetic dye, was selected as an analyte, and a fast method using square wave voltammetry was developed. Utilizing the 3D-printed G/C3N4/PLA electrode, a more comprehensive linear range (0.2 to 4.2 μmol/L), a 5-fold increase in sensitivity (9.83 μmol-1 L μA), and better limits of detection (LOD = 0.06 μmol/L) and quantification (LOQ = 0.18 μmol/L) were achieved compared to the G/PLA electrode. Samples of jelly, popsicles, isotonic drinks, and food flavoring samples were analyzed, and similar results to those obtained by UV-vis spectrometry confirmed the method's reliability. Therefore, the described sensor is a simple, cost-effective alternative for assessing AMR in routine food analysis.

Green processing via surface diffuse atmospheric plasma to enhance the dyeing performance on polylactic acid fabric

Poor dyeing performance has been a major defect of polylactic acid (PLA) fibers, which is caused by the lack of active chemical groups in PLA, and hinders the widespread use of this biodegradable material. Most of the existing chemical modification methods are not environmentally friendly and produce effluents. Herein, we report a green, efficient and continuous method to process PLA fibers via surface diffuse atmospheric plasma for the improvement of its hydrophilicity and dyeing performance. PLA fibers were processed via atmospheric plasma for grafting oxygen-containing functional groups, such as carboxyl, to achieve hydrophilicity and, meanwhile, strengthen the binding interactions with various dye molecules via covalent bonds, ionic bonds, or hydrogen bonds. In addition, different mechanisms of improving the dyeing performance on plasma-modified PLA fibers with different kinds of dyes have been discussed. This approach of material modification involves no chemical additives and has high processing efficiency, showing the potential applicability of green treatment to products in various fields.

A 3D-Printed Scaffold for Repairing Bone Defects

The treatment of bone defects has always posed challenges in the field of orthopedics. Scaffolds, as a vital component of bone tissue engineering, offer significant advantages in the research and treatment of clinical bone defects. This study aims to provide an overview of how 3D printing technology is applied in the production of bone repair scaffolds. Depending on the materials used, the 3D-printed scaffolds can be classified into two types: single-component scaffolds and composite scaffolds. We have conducted a comprehensive analysis of material composition, the characteristics of 3D printing, performance, advantages, disadvantages, and applications for each scaffold type. Furthermore, based on the current research status and progress, we offer suggestions for future research in this area. In conclusion, this review acts as a valuable reference for advancing the research in the field of bone repair scaffolds.

Characterization of Natural and Synthetic Fabrics for the Treatment of Complex Wastes

In the present study, nine fabrics have been tested for brackish water treatment with the aim of industrial application under the concept of zero liquid discharge (ZLD). Moisture content was determined, where it was observed that the lignocellulosic fabrics had a moisture content ranging from 2.5 to 8.5%. The wetting contact angle showed that the flax with polylactic acid (LPLA) was the most hydrophobic. The determination of the liquid absorption capacity showed that, of the synthetic fabrics, the one with the highest absorption, both in distilled water and in brackish water, was the polyester (PES) fabric with an absorption of 816% compared to its initial weight. In the natural fabrics, the highest absorption capacity was shown by the wet-laid without treatment (WL-WT) fabric for both distilled water and brackish water, although it required several cycles of operation to maintain this stable absorption. Exposure to brackish water improved the absorption capacity of all samples. Mechanical and thermal characterization showed that the synthetic fabrics were more resistant than the natural fabrics, although they may compete in terms of applicability. The capillarity study showed that the most hydrophilic fabrics completed the test the fastest. Finally, the composting degradation test showed that those fabrics with polylactic acid (PLA) content degraded faster in the first 14 days and thereafter the degradation of the lignocellulosic content showed a slower degradation until 112 days. The Bam fabric did not degrade during the course of the experiment.

Microbial colonization patterns and biodegradation of petrochemical and biodegradable plastics in lake waters: insights from a field experiment

Introduction

Once dispersed in water, plastic materials become promptly colonized by biofilm-forming microorganisms, commonly known as plastisphere.

Methods

By combining DNA sequencing and Confocal Laser Scanning Microscopy (CLSM), we investigated the plastisphere colonization patterns following exposure to natural lake waters (up to 77 days) of either petrochemical or biodegradable plastic materials (low density polyethylene - LDPE, polyethylene terephthalate - PET, polylactic acid - PLA, and the starch-based MaterBi® - Mb) in comparison to planktonic community composition. Chemical composition, water wettability, and morphology of plastic surfaces were evaluated, through Transform Infrared Spectroscopy (ATR-FTIR), Scanning Electron Microscopy (SEM), and static contact angle analysis, to assess the possible effects of microbial colonization and biodegradation activity.

Results and Discussion

The phylogenetic composition of plastisphere and planktonic communities was notably different. Pioneering microbial colonisers, likely selected from lake waters, were found associated with all plastic materials, along with a core of more than 30 abundant bacterial families associated with all polymers. The different plastic materials, either derived from petrochemical hydrocarbons (i.e., LDPE and PET) or biodegradable (PLA and Mb), were used by opportunistic aquatic microorganisms as adhesion surfaces rather than carbon sources. The Mb-associated microorganisms (i.e. mostly members of the family Burkholderiaceae) were likely able to degrade the starch residues on the polymer surfaces, although the Mb matrix maintained its original chemical structure and morphology. Overall, our findings provide insights into the complex interactions between aquatic microorganisms and plastic materials found in lake waters, highlighting the importance of understanding the plastisphere dynamics to better manage the fate of plastic debris in the environment.

Osseointegration enhancement by controlling dispersion state of carbonate apatite in polylactic acid implant

Osteoconductive ceramics (OCs) are often used to endow polylactic acid (PLA) with osseointegration ability. Conventionally, OC powder is dispersed in PLA. However, considering cell attachment to the implant, OCs may be more favorable when they exist in the form of aggregations, such as granules, and are larger than the cells rather than being dispersed like a powder. In this study, to clarify the effects of the dispersion state of OCs on the osseointegration ability, carbonate apatite (CAp), a bone mineral analog that is osteoconductive and bioresorbable, powder-PLA (P-PLA), and CAp granule-PLA (G-PLA) composite implants were fabricated via thermal pressing. The powder and granule sizes of CAp were approximately 1 and 300-600 µm, respectively. G-PLA exhibited a higher water wettability and released calcium and phosphate ions faster than P-PLA. When cylindrical G-PLA, P-PLA, and PLA were implanted in rabbit tibial bone defects, G-PLA promoted bone maturation compared to P-PLA and pure PLA. Furthermore, G-PLA bonded directly to the host bone, whereas P-PLA bonded across the osteoid layers. Consequently, the bone-to-implant contact of G-PLA was 1.8- and 5.6-fold higher than those of P-PLA and PLA, respectively. Furthermore, the adhesive shear strength of G-PLA was 1.9- and 3.0-fold higher than those of P-PLA and PLA, respectively. Thus, G-PLA achieved earlier and stronger osseointegration than P-PLA or PLA. The findings of this study highlight the significance of the state of dispersion of OCs in implants as a novel strategy for material development.

Improvement of the Ductility of Environmentally Friendly Poly(lactide) Composites with Posidonia oceanica Wastes Plasticized with an Ester of Cinnamic Acid

New composite materials were developed with poly(lactide) (PLA) and Posidonia oceanica fibers through reactive extrusion in the presence of dicumyl peroxide (DCP) and subsequent injection molding. The effect of different amounts of methyl trans-cinnamate (MTC) on the mechanical, thermal, thermomechanical, and wettability properties was studied. The results showed that the presence of Posidonia oceanica fibers generated disruptions in the PLA matrix, causing a decrease in the tensile mechanical properties and causing an impact on the strength due to the stress concentration phenomenon. Reactive extrusion with DCP improved the PO/PLA interaction, diminishing the gap between the fibers and the surrounding matrix, as corroborated by field emission scanning electron microscopy (FESEM). It was observed that 20 phr (parts by weight of the MTC, per one hundred parts by weight of the PO/PLA composite) led to a noticeable plasticizing effect, significantly increasing the elongation at break from 7.1% of neat PLA to 31.1%, which means an improvement of 338%. A considerable decrease in the glass transition temperature, from 61.1 °C of neat PLA to 41.6 °C, was also observed. Thermogravimetric analysis (TGA) showed a loss of thermal stability of the plasticized composites, mainly due to the volatility of the cinnamate ester, leading to a decrease in the onset degradation temperature above 10 phr MTC.

Surface Functionalization of Poly(lactic acid) via Deposition of Hydroxyapatite Monolayers for Biomedical Applications

The surface modification of poly(lactic acid) (PLA) using hydroxyapatite (HAP) particles via Langmuir-Blodgett (LB) and Langmuir-Schaefer (LS) approaches has been reported. The HAP monolayer was characterized at the air/water interface and deposited on three-dimensional (3D) printed poly(lactic acid). The deposition of HAP particles using the LS approach led to a larger surface coverage in comparison to the LB method, which produces a less uniform coating because of the aggregation of the particles. After the transfer of HAP on the PLA surface, the wettability values remained within the desired range. The presence of HAP on the surface of the polymer altered the topography and roughness in the nanoscale, as evidenced by the atomic force microscopy (AFM) images. This effect can be beneficial for the osteointegration of polymeric implants at an early stage, as well as for the reduction of the adherence of the microbial biofilm. Overall, the results suggest that the LS technique could be a promising approach for surface modification of PLA by hydroxyapatite with respective advantages in the biomedical field.

Simple Non-Equilibrium Atmospheric Plasma Post-Treatment Strategy for Surface Coating of Digital Light Processed 3D-Printed Vanillin-Based Schiff-Base Thermosets

A simple non-equilibrium atmospheric plasma post-treatment strategy was developed for the surface coating of three-dimensional (3D) structures produced by digital light processing 3D printing. The influence of non-equilibrium atmospheric plasma on the chemical and physical properties of vanillin-derived Schiff-base thermosets and the dip-coating process was investigated and compared to the influence of traditional post-treatment with UV-light. As a comparison, thermosets without post-treatment were also subjected to the coating procedure. The results document that UV post-treatment can induce the completion of the curing of the printed thermosets if complete curing is not reached during printing. Conversely, the plasma post-treatment does not contribute to the curing of the thermoset but causes some opening of the imine bonds and the regeneration of aldehyde functions. As a consequence, no great differences are observed between the not post-treated and plasma post-treated samples in terms of mechanical, thermal, and solvent-resistant properties. In contrast to the UV post-treatment, the plasma post-treatment of the thermosets induces a noticeable increase of the thermoset hydrophilicity ascribed to the reformation of amines on the thermoset surface. The successful coating process and the greatest uniformity of the lignosulfonate coating on the surface of plasma post-treated samples are considered to be due to the presence of these amines and aldehydes. The investigation of the UV shielding properties and antioxidant activities documents the increase of both properties with the increasing amount and uniformity of the formed coating. Interestingly, evident antioxidant properties are also shown by the noncoated thermosets, which are deduced to their chemical structures.

Non-thermal plasma disinfecting procedure is harmless to delicate items of everyday use

Non-thermal plasma (NTP) is a well-known decontamination tool applicable for a wide range of microorganisms and viruses. Since the recent COVID-19 pandemic highlighted the need to decontaminate all daily used items, it is highly desirable to address the applicability of NTP, including its possible harmful effects. To the best of our knowledge, a comprehensive characterization of NTP effects on sensitive materials is still lacking. We investigated the potential damage to common materials of daily use inflicted by air atmospheric NTP generated in Plasmatico v1.0. The materials tested were paper, various metals, and passive and active electronic components modelling sensitive parts of commonly used small electronic devices. The NTP-exposed paper remained fully usable with only slight changes in its properties, such as whitening, pH change, and degree of polymerization. NTP caused mild oxidation of copper, tinned copper, brass, and a very mild oxidation of stainless steel. However, these changes do not affect the normal functionality of these materials. No significant changes were observed for passive electronic components; active components displayed a very slight shift of the measured values observed for the humidity sensor. In conclusion, NTP can be considered a gentle tool suitable for decontamination of various sensitive materials.

Chitosan-Based High-Intensity Modification of the Biodegradable Substitutes for Cancellous Bone

An innovative approach to treating bone defects is using synthetic bone substitutes made of biomaterials. The proposed method to obtain polylactide scaffolds using the phase inversion technique with a freeze extraction variant enables the production of substitutes with morphology similar to cancellous bone (pore size 100-400 µm, open porosity 94%). The high absorbability of the implants will enable their use as platelet-rich plasma (PRP) carriers in future medical devices. Surface modification by dipping enabled the deposition of the hydrophilic chitosan (CS) layer, maintaining good bone tissue properties and high absorbability (850% dry weight). Introducing CS increases surface roughness and causes local changes in surface free energy, promoting bone cell adhesion. Through this research, we have developed a new and original method of low-temperature modification of PLA substitutes with chitosan. This method uses non-toxic reagents that do not cause changes in the structure of the PLA matrix. The obtained bone substitutes are characterised by exceptionally high hydrophilicity and morphology similar to spongy bone. In vitro studies were performed to analyse the effect of morphology and chitosan on cellular viability. Substitutes with properties similar to those of cancellous bone and which promote bone cell growth were obtained.

Inflammation Responses to Bone Scaffolds under Mechanical Stimuli in Bone Regeneration

Physical stimuli play an important role in one tissue engineering. Mechanical stimuli, such as ultrasound with cyclic loading, are widely used to promote bone osteogenesis; however, the inflammatory response under physical stimuli has not been well studied. In this paper, the signaling pathways related to inflammatory responses in bone tissue engineering are evaluated, and the application of physical stimulation to promote osteogenesis and its related mechanisms are reviewed in detail; in particular, how physical stimulation alleviates inflammatory responses during transplantation when employing a bone scaffolding strategy is discussed. It is concluded that physical stimulation (e.g., ultrasound and cyclic stress) helps to promote osteogenesis while reducing the inflammatory response. In addition, apart from 2D cell culture, more consideration should be given to the mechanical stimuli applied to 3D scaffolds and the effects of different force moduli while evaluating inflammatory responses. This will facilitate the application of physiotherapy in bone tissue engineering.

Effect of cold plasma treatment on polylactic acid and polylactic acid/poly (ethylene glycol) films developed as a drug delivery system for streptomycin sulfate

Polylactic acid (PLA) being a renewable polyester have extensively researched in the biomedical field due to its non-toxicity, high biocompatibility, and easy processing properties. However, low functionalization ability and hydrophobicity limit its applications and hence demands physical and chemical modifications to overcome these limitations. Cold plasma treatment (CPT) is frequently used to improve the hydrophilic properties of PLA-based biomaterials. This provides an advantage to obtain a controlled drug release profile in drug delivery systems. The rapid drug release profile may be advantageous in some applications such as wound application. The main objective of this study is to determine the effects of CPT on PLA or PLA@polyethylene glycol (PLA@PEG) porous films fabricated by solution casting method for use as a drug delivery system with a rapid release profile. The physical, chemical, morphological and drug release properties of PLA and PLA@PEG films, such as surface topography, thickness, porosity, water contact angle (WCA), chemical structure, and streptomycin sulfate release properties, after CPT were systematically investigated. XRD, XPS and FTIR results showed that oxygen-containing functional groups were formed on the film surface with CPT without changing the bulk properties. Along with the changes in the surface morphology such as surface roughness and porosity, the new functional groups provide the films hydrophilic properties by reducing the water contact angle. The improved surface properties enabled the selected model drug, streptomycin sulfate, to exhibit a faster release profile with drug-released mechanism fitted by first order kinetic model. Considering all the results, the prepared films showed an enormous potential for future drug delivery applications, especially in wound application where rapid drug release profile is an advantage.

Promising Agromaterials Based on Biodegradable Polymers: Polylactide and Poly-3-Hydroxybutyrate

Electrospun fabrics have unique properties due to their uniform morphology and high surface area to volume ratio. Ultrathin nonwoven fabrics are produced for many applications: biomedical, nanosensors, tissue engineering and filtration systems. In this work, nonwoven polylactide, polylactide/natural rubber, poly-3-hydroxybutyrate, and poly-3-hydroxybutyrate/nitrile butadiene rubber fabrics were prepared by electrospinning methods. The obtained fabric samples were used as substrates for the growth of winter wheat seeds "Yubileinaya 100" (Triticum aestivum L.). The stimulating effect of polymer substrates on seed germination and plant growth was shown. The structure and properties of nonwoven agromaterials were controlled by differential scanning calorimetry, IR-spectroscopy, and optical microscopy. The mechanical properties of the obtained fabrics before and after their utilization as substrates were studied. After the wheat growing experiment, the degree of crystallinity of PHB and PHB/NBR samples decreased by 12% and they completely lost their mechanical properties. It is shown that the main factors providing the efficiency of seed growth technology on polymer substrates are the chemical nature and structure of the biodegradable matrix.

Covalent Grafting of 5-Aminolevulinic Acid onto Polylactic Acid Films and Their Photodynamic Potency in Preserving Salmon

A novel photodynamic inactivation (PDI)-mediated antimicrobial film of polylactic acid/5-aminolevulinic acid (PLA/ALA) was successfully fabricated by a covalent grafting method using low-temperature plasma. The chemical structure, surface morphology, hydrophilic ability, and mechanical and barrier properties of the films were characterized, and their antibacterial, anti-biofilm potency and preservation effects on ready-to-eat salmon were investigated during storage. Results showed that the amino group of ALA was covalently grafted with the carboxyl group on the surface of PLA after the plasma treatment, with the highest grafting rate reaching ∼50%. The fabricated PLA/ALA films displayed an enhanced barrier ability against water vapor and oxygen. Under blue light-emitting diode illumination, the PLA/ALA films generated massive reactive oxygen species from the endogenous porphyrins in cells induced by ALA and then fatally destroyed the cell wall of planktonic cells and the architectural structures of sessile biofilms of the pathogens (Listeria monocytogenes and Vibrio parahaemolyticus) and spoilage bacterium (Shewanella putrefaciens). More importantly, the PDI-mediated PLA/ALA films potently inhibited 99.9% native bacteria on ready-to-eat salmon and significantly suppressed the changes of its drip loss, pH, and lipid oxidation (MDA) during storage, and on this basis, the shelf life of salmon was extended by 4 days compared with that of the commercial polyethylene film. Therefore, the PDI-mediated PLA/ALA films are valid in inactivating harmful bacterial and preserving the quality of seafood.

Effect of Non-Thermal Food Processing Techniques on Selected Packaging Materials

In the last decade both scientific and industrial community focuses on food with the highest nutritional and organoleptic quality, together with appropriate safety. Accordingly, strong efforts have been made in finding appropriate emerging technologies for food processing and packaging. Parallel to this, an enormous effort is also made to decrease the negative impact of synthetic polymers not only on food products (migration issues) but on the entire environment (pollution). The science of packaging is also subjected to changes, resulting in development of novel biomaterials, biodegradable or not, with active, smart, edible and intelligent properties. Combining non-thermal processing with new materials opens completely new interdisciplinary area of interest for both food and material scientists. The aim of this review article is to give an insight in the latest research data about synergies between non-thermal processing technologies and selected packaging materials/concepts.

Additive Manufacturing of Biomaterials-Design Principles and Their Implementation

Additive manufacturing (AM, also known as 3D printing) is an advanced manufacturing technique that has enabled progress in the design and fabrication of customised or patient-specific (meta-)biomaterials and biomedical devices (e.g., implants, prosthetics, and orthotics) with complex internal microstructures and tuneable properties. In the past few decades, several design guidelines have been proposed for creating porous lattice structures, particularly for biomedical applications. Meanwhile, the capabilities of AM to fabricate a wide range of biomaterials, including metals and their alloys, polymers, and ceramics, have been exploited, offering unprecedented benefits to medical professionals and patients alike. In this review article, we provide an overview of the design principles that have been developed and used for the AM of biomaterials as well as those dealing with three major categories of biomaterials, i.e., metals (and their alloys), polymers, and ceramics. The design strategies can be categorised as: library-based design, topology optimisation, bio-inspired design, and meta-biomaterials. Recent developments related to the biomedical applications and fabrication methods of AM aimed at enhancing the quality of final 3D-printed biomaterials and improving their physical, mechanical, and biological characteristics are also highlighted. Finally, examples of 3D-printed biomaterials with tuned properties and functionalities are presented.

A Sustainable and Antimicrobial Food Packaging Film for Potential Application in Fresh Produce Packaging

N-halamines are a group of compounds containing one or more nitrogen-halogen covalent bond(s). This high-energy halide bond provides a strong oxidative state so that it is able to inactivate microorganisms effectively. In this study, a sustainable film was developed based on polylactic acid (PLA) with incorporated N-halamine compound 1-chloro-2,2,5,5-tetramethyl-4-imidazolidinone (MC), as a promising antimicrobial food packaging material. Results showed that the incorporation of MC prevented the crystallization of PLA and improved the physical properties of the films. In addition, both the moisture barrier and the oxygen permeability were improved with the presence of MC. Importantly, the antimicrobial film was able to inactivate inoculated microorganisms by a factor of seven log cycles in as little as 5 min of contact. Films that contained higher levels of MC further enhanced the antimicrobial efficacy. Fresh strawberries packed with the fabricated films maintained the quality for up to 5 days. Due to the ease of fabrication and the effective biocidal property, these films have a wide range of potential applications in the field of food packaging to extend the shelf life of fresh produce.

Reactive Magnetron Plasma Modification of Electrospun PLLA Scaffolds with Incorporated Chloramphenicol for Controlled Drug Release

Surface modification with the plasma of the direct current reactive magnetron sputtering has demonstrated its efficacy as a tool for enhancing the biocompatibility of polymeric electrospun scaffolds. Improvement of the surface wettability of materials with water, as well as the formation of active chemical bonds in the near-surface layers, are the main reasons for the described effect. These surface effects are also known to increase the release rate of drugs incorporated in fibers. Herein, we investigated the effect of plasma modification on the chloramphenicol release from electrospun poly (lactic acid) fibrous scaffolds. Scaffolds with high-50 wt./wt.%-drug content were obtained. It was shown that plasma modification leads to an increase in the drug release rate and drug diffusion coefficient, while not deteriorating surface morphology and mechanical properties of scaffolds. The materials' antibacterial activity was observed to increase in the first day of the experiment, while remaining on the same level as the unmodified group during the next six days. The proposed technique for modifying the surface of scaffolds will be useful for obtaining drug delivery systems with controlled accelerated release, which can expand the possibilities of local applications of antibiotics and other drugs.

One-Pot Preparation of Hydrophilic Polylactide Porous Scaffolds by Using Safe Solvent and Choline Taurinate Ionic Liquid

Polylactides (PLAs) are a class of polymers that are very appealing in biomedical applications due to their degradability in nontoxic products, tunable structural, and mechanical properties. However, they have some drawbacks related to their high hydrophobicity, lack of functional groups able to graft bioactive molecules, and solubility in unsafe solvents. To circumvent these shortcomings, porous scaffolds for tissue engineering were prepared by vigorously mixing a solution of isotactic and atactic PLA in nontoxic ethyl acetate at 70 °C with a water solution of choline taurinate. The partial aminolysis of the polymer ester bonds by taurine -NH2 brought about the formation of PLA oligomers with surfactant activity that stabilized the water-in-oil emulsion. Upon drying, a negligible shrinking occurred, and mechanically stable porous scaffolds were obtained. By varying the polymer composition and choline taurinate concentration, it was possible to modulate the pore dimensions (30-50 µm) and mechanical properties (Young's moduli: 1-6 MPa) of the samples. Furthermore, the grafted choline taurinate made the surface of the PLA films hydrophilic, as observed by contact angle measurements (advancing contact angle: 76°; receding contact angle: 40°-13°). The preparation method was very simple because it was based on a one-pot mild reaction that did not require an additional purification step, as all the employed chemicals were nontoxic.

Deposition of Biocompatible Polymers by 3D Printing (FDM) on Titanium Alloy

Nowadays, the replacement of a hip joint is a standard surgical procedure. However, researchers have continuingly been trying to upgrade endoprostheses and make them more similar to natural joints. The use of 3D printing could be helpful in such cases, since 3D-printed elements could mimic the natural lubrication mechanism of the meniscus. In this paper, we propose a method to deposit plastics directly on titanium alloy using 3D printing (FDM). This procedure allows one to obtain endoprostheses that are more similar to natural joints, easier to manufacture and have fewer components. During the research, biocompatible polymers suitable for 3D FDM printing were used, namely polylactide (PLA) and polyamide (PA). The research included tensile and shear tests of metal–polymer bonds, friction coefficient measurements and microscopic observations. The friction coefficient measurements revealed that only PA was promising for endoprostheses (the friction coefficient for PLA was too high). The strength tests and microscopic observations showed that PLA and PA deposition by 3D FDM printing directly on Ti6Al4V titanium alloy is possible; however, the achieved bonding strength and repeatability of the process were unsatisfactory. Nevertheless, the benefits arising from application of this method mean that it is worthwhile to continue working on this issue.

Surface Modification of Commingled Flax/PP and Flax/PLA Fibres by Silane or Atmospheric Argon Plasma Exposure to Improve Fibre–Matrix Adhesion in Composites

Challenges faced by natural fibre-reinforced composites include poor compatibility between hydrophilic fibres such as flax and hydrophobic polymeric matrices such as polypropylene (PP) or poly(lactic acid) (PLA), and their inherent flammability. The former promotes weak interfacial adhesion between fibre and matrix, which may be further compromised by the addition of a flame retardant. This paper investigates the effect that the added flame retardant (FR), guanylurea methylphosphonate (GUP) and selected surface treatments of commingled flax and either PP or PLA fabrics have on the fibre/matrix interfacial cohesive forces in derived composites. Surface treatments included silanisation and atmospheric plasma flame exposure undertaken both individually and in sequence. 1-, 2- and 8-layered composite laminates were examined for their tensile, peeling and flexural properties, respectively, all of which yield measures of fibre-matrix cohesion. For FR-treated Flax/PP composites, maximum improvement was obtained with the combination of silane (using vinyltriethoxysilane) and plasma (150 W) treatments, with the highest peeling strength and flexural properties. However, for FR-treated Flax/PLA composites, maximum improvement in both properties occurred following 150 W plasma exposure only. The improvements in physical properties were matched by increased fibre-matrix adhesion as shown in SEM images of fractured laminates in which fibre-pullout had been eliminated.

Surface Modification of Poly(lactic acid) Film via Cold Plasma Assisted Grafting of Fumaric and Ascorbic Acid

Plant-based materials have found their application in the packaging with a yearly growing production rate. These naturally biodegradable polymers are obtained from renewable and sustainable natural resources with reduced environmental impact and affordable cost. These materials have found their utilization in fully-renewable plant-based packaging products, such as Tetra Pak^®-like containers, by replacing commonly-used polyethylene as the polymer component. Poly(lactic acid) (PLA) is one of the representative plant-based polymers because of its eco-friendliness and excellent chemical and mechanical properties. In this work, a PLA surface was modified by various food additives, namely ascorbic acid (ASA) and fumaric acid (FA), using plasma-initiated grafting reactions in order to improve the surface and adhesion properties of PLA. Various analytical and microscopic techniques were employed to prove the grafting process. Moreover, the improved adhesion of the modified PLA foil to aluminum (Al) foil in a laminate configuration was proven by peel resistance measurements. The peel resistance of modified PLA increased by 74% and 184% for samples modified by ASA and FA, respectively, compared with untreated PLA.

Improvement in the Filtration Performance of an Ultraporous Nanofiber Membrane by Atmospheric Pressure Plasma-Induced Surface Modification

Nanofiber membranes have outstanding potential for filtration applications due to their great specific surface area, high porosity, and modifiable structure. Compared to conventional membranes, nanofiber membranes offer substantial high flux and high rejection ratios. This paper provides a comprehensive analysis on the filtration performance of plasma treatment on the polyacrylonitrile nanofiber membrane. The pores in the original membrane were utilized about a mere 10%, while those of the plasma-irradiated membrane were utilized nearly 60%. The membrane modification was performed using N2, O2, and Ar plasma. It was found that Ar plasma was most effective for etching the membrane structure. Fourier transform infrared spectroscopy was applied to detect the chemical changes on the membranes. The contact angle of the water droplets on the original membrane was 96.1°; however, after the Ar plasma treatment, it declined to 0°. Finally, the particle retention details in different cross sections of the filtered membranes were observed via a scanning electron microscope. The main innovation is to clarify the changes in the mechanism of the nanofiber membrane trapping particles before and after plasma treatment. In the filtration test after plasma treatment, the internal space of the membrane was fully and effectively utilized, and the flux was also improved. The obtained results suggest a potential application of the plasma-treated nanofiber membrane in water treatment.

Multilayer Films Based on Poly(lactic acid)/Gelatin Supplemented with Cellulose Nanocrystals and Antioxidant Extract from Almond Shell By-Product and Its Application on Hass Avocado Preservation

In this work, poly(lactic acid) (PLA)/gelatin/PLA multilayer films supplemented with cellulose nanocrystals and antioxidant extract from almond shell (AS) by-products were developed by solvent casting technique for active food packaging. The almond shell antioxidant extract (ASE) was obtained by microwave-assisted extraction, while cellulose nanocrystals (CNCs) were extracted from AS by a sequential process of alkalization, acetylation and acid hydrolysis. Four formulations were obtained by adding 0 (control), 6 wt.% of ASE (FG/ASE), 4.5 wt.% of CNCs (FG/CNC) and 6 wt.% + 4.5 wt.% of ASE + CNCs, respectively, (FG/ASE + CNC) into fish gelatin (FG). PLA/FG/PLA multilayer films were prepared by stacking two outer PLA layers into a middle FG film. A surface modification of PLA by air atmospheric plasma treatment was optimized before multilayer development to improve PLA adhesion. Complete characterization of the multilayers underlined the FG/ASE + CNC formulation as a promising active reinforced packaging system for food preservation, with low values of transparency, lightness and whiteness index. A good adhesion and homogeneity of the multilayer system was obtained by SEM, and they also demonstrated low oxygen permeability (40.87 ± 5.20 cm³ mm m^-2 day) and solubility (39.19 ± 0.16%) values, while mechanical properties were comparable with commercial plastic films. The developed multilayer films were applied to Hass avocado preservation. The initial degradation temperature (T_ini), DSC parameters and in vitro antioxidant capacity of the films were in accordance with the low peroxide and anisidine values obtained from avocado pulp after packaging for 14 days at 4 °C. The developed PLA/FG/PLA films supplemented with 6 wt.% ASE+ 4.5 wt.% CNCs may be potential bioactive packaging systems for fat food preservation.

Application of Vegetal Oils in Developing Bioactive Paper-Based Materials for Food Packaging

A major disadvantage of conventional food packaging materials is the difficulty in disposal and recycling, due to their high stability to environmental and thermal stress. The trend now is to develop new eco-friendly food packaging that can substitute fossil fuel derived materials. Cellulose, the main constituent of paper-based food packages, is a favorable starting material for such purpose. In this study we present a new method to obtain bioactive paper based materials suitable for food packaging applications. By combining eco-friendly activation processes (cold plasma or gamma irradiation) and bioactive plant oils (clove essential oil and rosehip seeds vegetal oil) for modification of kraft paper, new materials with antioxidant and antibacterial activity were obtained. The oil-loaded bioactive paper based materials presented increased hydrophobicity (from 97° contact angle in the case of kraft paper to 115° for oil-loaded sample) and decreased water adsorption (a one-quarter decrease). Due to various interactions with the functional groups of plant oils, the modified kraft paper presents different antibacterial and antioxidant properties. Essential clove oil imprinted higher antioxidant activity (owing to the high content in eugenol and eugenol acetate phenolic compounds) and was more efficient in reducing the bacterial growth on fresh beef meat and on fresh curd cheese. The cold pressed rosehip seeds oil acted as aslightly better antibacterial agent against Listeria monocytogenes (+), Salmonella enteritidis (−) and Escherichia coli (−) bacterial strains. Thus, the newly developed bioactive paper could be used as effective packaging material that can help preserving food quality for longer time.

Effect of Plasma Surface Modification on Print Quality of Biodegradable PLA Films

PLA films, as non-absorbent materials, require modification of the surface before the printing process in order to improve the wettability of the substrate and to obtain proper ink adhesion to the substrate. In this paper, the surfaces of two kinds of PLA films were modified using plasma activation with parameters enabling high surface free energy (SFE) values, and then the films were printed on using different kinds of flexographic inks. Two gases, oxygen and argon, were used for activation, as these make it possible to obtain good hydrophilicity and high SFE values while having different effects on the roughness, or the degree of surface etching. Plasma-activated films were subsequently subjected to the measurements of: contact angle with water, diiodomethane and three printing inks, roughness, weight change, strength properties, color and gloss change, and SFE was determined. Unmodified and activated films were flexographically printed in laboratory conditions and then the quality of obtained prints was analyzed. The results showed a strong effect of activation with both oxygen and argon plasma on the SFE value of the films and the contact angles of water and inks, with the gas used for plasma activation and the type of film significantly influencing the thickness of the fused ink layer and the resultant color. Moreover, plasma activation had a especially favorable and significant effect on the quality of prints made with water-based inks, while it had little effect when printing with solvent-based inks.

The Effect of Molecular Weight on the Antimicrobial Activity of Chitosan from Loligo opalescens for Food Packaging Applications

The growing requirement for sustainable processes has boosted the development of biodegradable plastic-based materials incorporating bioactive compounds obtained from waste, adding value to these products. Chitosan (Ch) is a biopolymer that can be obtained by deacetylation of chitin (found abundantly in waste from the fishery industry) and has valuable properties such as biocompatibility, biodegradability, antimicrobial activity, and easy film-forming ability. This study aimed to produce and characterize poly(lactic acid) (PLA) surfaces coated with β-chitosan and β-chitooligosaccharides from a Loligo opalescens pen with different molecular weights for application in the food industry. The PLA films with native and depolymerized Ch were functionalized through plasma oxygen treatment followed by dip-coating, and their physicochemical properties were assessed by Fourier-transform infrared spectroscopy, X-ray diffraction, water contact angle, and scanning electron microscopy. Their antimicrobial properties were assessed against Escherichia coli and Pseudomonas putida, where Ch-based surfaces reduced the number of biofilm viable, viable but nonculturable, and culturable cells by up to 73%, 74%, and 87%, respectively, compared to PLA. Biofilm growth inhibition was confirmed by confocal laser scanning microscopy. Results suggest that Ch films of higher molecular weight had higher antibiofilm activity under the food storage conditions mimicked in this work, contributing simultaneously to the reuse of marine waste.

Surface Modification of Poly(l-lactic acid) through Stereocomplexation with Enantiomeric Poly(d-lactic acid) and Its Copolymer

Poly(l-lactic acid) with high molecular weight was used to prepare PLLA films by means of the solvent casting technique. Poly(d-lactic acid) (PDLA) and poly(d-lactic acid-co-glucose) copolymer (PDLAG) with a low molecular weight were synthesized from d-lactic acid and glucose through melt polycondensation. PLLA films were immersed in PDLA or PDLAG solution to prepare surface-modified PLLA films. The modified PLLA film presented stereocomplex crystal (SC) on its surface and homogeneous crystals (HC) in its bulk. The HC structure and surface morphology of modified PLLA films were obviously damaged by PDLA or PDLAG solution. With increasing immersion time, the PLLA films modified by PDLA decreased both the HC and SC structure, while the PLLA films modified by PDLAG increased the SC structure and decreased the HC structure. Hydrophilic glucose residues of PDLAG on the surface would improve the hydrophilicity of surface-modified PLLA films. Moreover, the hydrophilicity of glucose residues and the interaction of glucose residues with lactic acid units could retard HC destruction and SC crystallization, so that PLLA films modified by PDLAG possessed lower melting temperatures of HC and SC, the crystallinity of SC and the water contact angle, compared with PDLAG-modified PLLA films. The SC structure could improve the heat resistance of modified PLLA film, but glucose residues could block crystallization to promote the thermal degradation of PLA materials. The surface modification of PLLA films will improve the thermal stability, hydrophilicity and crystallization properties of PLA materials, which is essential in order to obtain PLA-based biomaterials.

On the Effectiveness of Oxygen Plasma and Alkali Surface Treatments to Modify the Properties of Polylactic Acid Scaffolds

Surface modification of 3D-printed PLA structures is a major issue in terms of increasing the biofunctionality and expanding the tissue engineering applications of these parts. In this paper, different exposure times were used for low-pressure oxygen plasma applied to PLA 3D-printed scaffolds. Alkali surface treatments were also evaluated, aiming to compare the modifications introduced on the surface properties by each strategy. Surface-treated samples were characterized through the quantification of carboxyl groups, energy-dispersive X-ray spectroscopy, water contact angle measurements, and differential scanning calorimetry analysis. The change in the surface properties was studied over a two-week period. In addition, an enzymatic degradation analysis was carried out to evaluate the effect of the surface treatments on the degradation profile of the 3D structures. The physicochemical characterization results suggest different mechanism pathways for each type of treatment. Alkali-treated scaffolds showed a higher concentration of carboxyl groups on their surface, which enhanced the enzymatic degradation rate, but were also proven to be more aggressive towards 3D-printed structures. In contrast, the application of the plasma treatments led to an increased hydrophilicity of the PLA surface without affecting the bulk properties. However, the changes on the properties were less steady over time.

Effect of Sanding and Plasma Treatment of 3D-Printed Parts on Bonding to Wood with PVAc Adhesive

Additive manufacturing is becoming increasingly important for manufacturing end products, not just prototyping. However, the size of 3D-printed products is limited due to available printer sizes and other technological limitations. For example, making furniture from 3D-printed parts and wooden elements requires adequate adhesive joints. Since materials for 3D printing usually do not bond very well with adhesives designed for woodworking, they require special surface preparation to improve adhesion. In this study, fused deposition modelling (FDM) 3D-printed parts made of polylactic acid (PLA), polylactic acid with wood flour additive (Wood-PLA), and acrylonitrile-butadiene-styrene (ABS) polymers were bonded to wood with polyvinyl acetate (PVAc) adhesive. The surfaces of the samples were bonded as either non-treated, sanded, plasma treated, or sanded and plasma treated to evaluate the effect of each surface preparation on the bondability of the 3D-printed surfaces. Different surface preparations affected the bond shear strength in different ways. The plasma treatment significantly reduced water contact angles on all tested printing materials and increased the bond tensile shear strength of the adhesive used. The increase in bond strength was highest for the surfaces that had been both sanded and plasma treated. The highest increase was found for the ABS material (untreated 0.05 MPa; sanded and plasma treated 4.83 MPa) followed by Wood-PLA (from 0.45 MPa to 3.96 MPa) and PLA (from 0.55 MPa to 3.72 MPa). Analysis with a scanning electron microscope showed the smooth surfaces of the 3D-printed parts, which became rougher with sanding with more protruded particles, but plasma treatment partially melted the surface structures on the thermoplastic polymer surfaces.

Recyclable and degradable nonwoven-based double-network composite hydrogel adsorbent for efficient removal of Pb(II) and Ni(II) from aqueous solution

This study reports a novel adsorbent structure and shows the satisfactory removal performance of Pb(II) and Ni(II). The fabric structure increases the strength of the hydrogel. The hydrogel plays a major role in the composite structure as a matrix, while the fabric bears the applied load and protects the structure from mechanical damage. The double-network composite hydrogel is reinforced by plasma grafted polylactic acid melt-blown non-woven fabric and polyethylene glycol dimaleate, and its compressive strength reaches 40.6 kPa at 60% strain. The interface substantially improves the compression strength by 42.9%. Through the adsorption isotherm model, the adsorption capacity of the hydrogel for Pb(II) and Ni(II) reaches 233.12 and 165.06 mg/g, respectively, and the removal rate of heavy metal ions in water at low concentrations exceeds 95%, showing the excellent removal rate of heavy metals. Even after the fifth cycle, the removal efficiency barely declines, indicating the feasibility of repeatedly use. Cost analysis reveals that the adsorbent is relatively low cost, solving the problems of difficult recovery, low strength, and easy damage of hydrogel adsorbents, and promoting the industrial application of hydrogels as adsorbents.

Modification of PLA Scaffold Surface for Medical Applications

Materials used for medical applications (e.g., the cellular scaffold) should have not only the specific chemical composition, but the surface layer properties as well. For this reason, a method which enables an increase in the number of pores, wettability of the surface, and improvement the conditions of nutrient transportation into the membrane is being studied. The plasma of a dielectric barrier discharge was applied for the surface modification of polylactide obtained by dry or wet phase inversion. The plasma-modified surface was analyzed by contact angle measurements with water and diiodomethane. The surface free energy (SFE) was calculated by the Owens–Wendt method. The highest SFE and its polar component (67.6 mJ/m2 and 39.5 mJ/m2, respectively) were received when the process was conducted in an Ar + CO2 gas mixture with a discharge power of 20 W. The purpose of this research was to increase the wettability and porosity of the membrane’s surface. It can be concluded that the dielectric barrier discharge can effectively change the surface of the polylactide membranes, and that the structure of the modified membranes was not damaged during modification. The process of modification was easier for the membranes made by dry phase inversion. These materials had higher SFE values after the modification.

Functionalization Strategies and Fabrication of Solvent-Cast PLLA for Bioresorbable Stents

Actual polymer bioresorbable stents (BRS) generate a risk of device thrombosis as a consequence of the incomplete endothelialization after stent implantation. The material-tissue interactions are not fully controlled and stent fabrication techniques do not allow personalized medical solutions. This work investigates the effect of different functionalization strategies onto solvent-cast poly(l-lactic acid) (PLLA) surfaces with the capacity to enhance surface endothelial adhesion and the fabrication of 3D printed BRS. PLLA films were obtained by solvent casting and treated thermally to increase mechanical properties. Surface functionalization was performed by oxygen plasma (OP), sodium hydroxide (SH) etching, or cutinase enzyme (ET) hydrolysis, generating hydroxyl and carboxyl groups. A higher amount of carboxyl and hydroxyl groups was determined on OP and ET compared to the SH surfaces, as determined by contact angle and X-ray photoelectron spectroscopy (XPS). Endothelial cells (ECs) adhesion and spreading was higher on OP and ET functionalized surfaces correlated with the increase of functional groups without affecting the degradation. To verify the feasibility of the approach proposed, 3D printed PLLA BRS stents were produced by the solvent-cast direct writing technique.