A new way of creating cellular polyurethane materials: NIPU foams

Preparation of Non-Isocyanate Polyurethanes from Mixed Cyclic-Carbonated Compounds: Soybean Oil and CO2-Based Poly(ether carbonate)

This study presents the synthesis and characterization of non-isocyanate polyurethanes (NIPU) derived from the copolymerization of cyclic-carbonated soybean oil (CSBO) and cyclic carbonate (CC)-terminated poly(ether carbonate) (RCC). Using a double-metal cyanide catalyst, poly(ether carbonate) polyol was first synthesized through the copolymerization of carbon dioxide and propylene oxide. The terminal hydroxyl group was then subjected to a substitution reaction with a five-membered CC group using glycerol-1,2-carbonate and oxalyl chloride, yielding RCC. Attempts to prepare NIPU solely using RCC and diamine were unsuccessful, possibly due to the low CC functionality and the aminolysis of RCC's linear carbonate repeating units. However, when combined with CSBO, solid NIPUs were successfully obtained, exhibiting good thermal stability along with enhanced mechanical properties compared to conventional CSBO-based NIPU formulations. Overall, this study underscores the potential of leveraging renewable resources and carbon capture technologies to develop sustainable NIPUs with tailored properties, thereby expanding their range of applications.

Cascade Exotherms for Rapidly Producing Hybrid Nonisocyanate Polyurethane Foams from Room Temperature Formulations

For decades, self-blown polyurethane foams─found in an impressive range of materials─are produced by the toxic isocyanate chemistry and are difficult to recycle. Producing them in existing production plants by a rapid isocyanate-free self-blowing process from room temperature (RT) formulations is a long-lasting challenge. The recent water-induced self-blowing of nonisocyanate polyurethane (NIPU) formulations composed of a CO2-based tricyclic carbonate, diamine, water, and a catalyst successfully addressed the isocyanate issue, however failed to provide foams at RT. Herein, we elaborate a practical solution to empower the NIPU foam formation in record timeframes from RT formulations. We generate cascade exotherms by the addition of a highly reactive triamine and an epoxide to the formulation of the water-induced self-foaming process. These exotherms, combined to a fast cross-linking imparted by the triamine and epoxide, rapidly raise the temperature to the foaming threshold and deliver hybrid NIPU foams in 5 min with KOH as a catalyst. Careful selection of the monomers enables producing foams with a wide range of properties, as well as with an unprecedented high biobased content up to 90 wt %. Moreover, foams can be upcycled into polymer films by hot pressing, offering them a facile reuse scenario. This robust cheap process opens huge perspectives for greener foams of high biobased contents, expectedly responding to the sustainability demands of the foam sector. It is potentially compatible to the retrofitting of industrial foaming infrastructures, which is of paramount importance to accommodate existing foam production plants and address the huge foam market demands.

Synthesis of Bis(cyclic carbonates) from Epoxy Resin under Microwave Irradiation: The Structural Analysis and Evaluation of Thermal Properties

This article describes the use of microwave irradiation in the synthesis of bis(cyclo carbonate) compounds (BCCs) in bulk (without solvent) from carbon dioxide capture using an epoxidized compound-a commercial epoxy resin-and compares this process to the conventional method. CO2 cycloaddition to epoxides is an ecological and efficient method for the formation of bis(cyclic carbonates). Moreover, the introduction of gas into the reaction mixture was carried out at atmospheric pressure with a controlled flow rate, which is advantageous from an economic point of view. Progressive structural changes and the presence of characteristic chemical groups were monitored using attenuated total reflectance infrared spectroscopy with Fourier transform. The obtained crude products were purified to obtain three fractions, which were subjected to detailed structural analysis using FT-IR and 13CNMR. The formation of the main product with two cyclic carbonates was confirmed. The presence of monomers, dimers and trimers in individual fractions as well as their thermal stability were determined, and the molecular masses in individual fractions were determined using gel permeation chromatography (GPC).

Innovations in applications and prospects of non-isocyanate polyurethane bioplastics

Currently, conventional plastics are necessary for a variety of aspects of modern daily life, including applications in the fields of healthcare, technology, and construction. However, they could also contain potentially hazardous compounds like isocyanates, whose degradation has a negative impact on both the environment and human health. Therefore, researchers are exploring alternatives to plastic which is sustainable and environmentally friendly without compromising its mechanical and physical features. This review study highlights the production of highly eco-friendly bioplastic as an efficient alternative to non-biodegradable conventional plastic. Bioplastics are produced from various renewable biomass sources such as plant debris, fatty acids, and oils. Poly-addition of di-isocyanates and polyols is a technique employed over decades to produce polyurethanes (PUs) bioplastics from renewable biomass feedstock. The toxicity of isocyanates is a major concern with the above-mentioned approach. Novel green synthetic approaches for polyurethanes without using isocyanates have been attracting greater interest in recent years to overcome the toxicity of isocyanate-containing raw materials. The polyaddition of cyclic carbonates (CCs) and polyfunctional amines appears to be the most promising method to obtain non-isocyanate polyurethanes (NIPUs). This method results in the creation of polymeric materials with distinctive and adaptable features with the elimination of harmful compounds. Consequently, non-isocyanate polyurethanes represent a new class of green polymeric materials. In this review study, we have discussed the possibility of creating novel NIPUs from renewable feedstocks in the context of the growing demand for efficient and ecologically friendly plastic products.

Exploiting the Use of the Decarboxylative S-Alkylation Reaction to Produce Self-Blowing, Recyclable Polycarbonate Foams

Polymeric foams are widely used in many industrial applications due to their light weight and superior thermal, mechanical, and optical properties. Currently, increasing research efforts is being directed towards the development of greener foam formulations that circumvent the use of isocyanates/blowing agents that are commonly used in the production of foam materials. Here, a straightforward, one-pot method is presented to prepare self-blown polycarbonate (PC) foams by exploiting the (decarboxylative) S-alkylation reaction for in situ generation of the blowing agent (CO2 ). The concomitant formation of a reactive alcohol intermediate promotes a cascade ring-opening polymerization of the cyclic carbonates to yield a cross-linked polymer network. It is shown that these hydroxyl-functionalized polycarbonate-based foams can be easily recycled into films through thermal compression molding. Furthermore, it is demonstrated that complete hydrolytic degradation of the foams is possible, thus offering the potential for zero-waste materials. This straightforward and versatile process broadens the scope of isocyanate-free, self-foaming materials, opening a new pathway for next-generation environmentally friendly foams.

Latest Advancements in the Development of High-Performance Lignin- and Tannin-Based Non-Isocyanate Polyurethane Adhesive for Wood Composites

The depletion of natural resources and increasing environmental apprehension regarding the reduction of harmful isocyanates employed in manufacturing polyurethanes (PUs) have generated significant attention from both industrial and academic sectors. This attention is focused on advancing bio-based non-isocyanate polyurethane (NIPU) resins as viable and sustainable substitutes, possessing satisfactory properties. This review presents a comprehensive analysis of the progress made in developing bio-based NIPU polymers for wood adhesive applications. The main aim of this paper is to conduct a comprehensive analysis of the latest advancements in the production of high-performance bio-based NIPU resins derived from lignin and tannin for wood composites. A comprehensive evaluation was conducted on scholarly publications retrieved from the Scopus database, encompassing the period from January 2010 to April 2023. In NIPU adhesive manufacturing, the exploration of substitute materials for isocyanates is imperative, due to their inherent toxicity, high cost, and limited availability. The process of demethylation and carbonation of lignin and tannin has the potential to produce polyphenolic compounds that possess hydroxyl and carbonyl functional groups. Bio-based NIPUs can be synthesized through the reaction involving diamine molecules. Previous studies have provided evidence indicating that NIPUs derived from lignin and tannin exhibit enhanced mechanical properties, decreased curing temperatures and shortened pressing durations, and are devoid of isocyanates. The characterization of NIPU adhesives based on lignin and tannin was conducted using various analytical techniques, including Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), matrix-assisted laser desorption/ionization with time-of-flight (MALDI-TOF) mass spectrometry, and gel permeation chromatography (GPC). The adhesive performance of tannin-based NIPU resins was shown to be superior to that of lignin-based NIPUs. This paper elucidates the potential of lignin and tannin as alternate sources for polyols in the manufacturing of NIPUs, specifically for their application as wood adhesives.

CO2-Blown Nonisocyanate Polyurethane Foams

Polyurethane (PU) foams are produced from toxic, petrochemical- and phosgene-derived isocyanates. Although nonisocyanate polyurethane (NIPU) has shown promise as a replacement for traditional PU, the synthesis of NIPU foams has not been widely studied due to the difficulties in replicating the foaming process of PU, in situ CO2 production through the hydrolysis of isocyanates. Hereby, we report the synthesis of amine-CO2 adducts and their CO2 adsorption-desorption characteristics under different conditions. The results show that the amine-CO2 adducts can exhibit up to 87% CO2 desorption at 60 °C after aminolysis with cyclic carbonate. The amine-CO2 adduct is used as both a foaming agent and a comonomer to obtain low-density foams (0.203-0.239 g·cm-3) after heating at 50-60 °C for 24-48 h. This marks the successful synthesis of in situ CO2-blown NIPU foams using an amine-CO2 adduct.

Tailor-Made Bio-Based Non-Isocyanate Polyurethanes (NIPUs)

Non-isocyanate polyurethanes (NIPUs) based on biobased polyamines and polycarbonates are a sustainable alternative to conventional polyurethanes (PU). This article discloses a novel method to control the crosslinking density of fully biobased isocyanate-free polyurethanes, synthesized from triglycerides carbonated previously in scCO₂ and different diamines, such as ethylenediamine (EDA), hexamethylenediamine (HMDA) and Priamine^TM-1075 (derived from a dimerized fatty acid). As capping substances, water or bioalcohols are used in such a way that the crosslinking density can be adjusted to suit the requirements of the intended application. An optimization of the NIPU synthesis procedure is firstly carried out, establishing the polymerization kinetics and proposing optimal conditions set for the synthesis of the NIPUs. Then, the influence of the partial blocking of the active polymerization sites of the carbonated soybean oil (CSBO), using monofunctional amines, on the physical properties of the NIPUS is explored. Finally, the synthesis of fully biobased NIPUs with a targeted crosslinking density is achieved using hybrid NIPUs, employing partially carbonated oil and H₂O or ethanol as blockers to achieve the desired physical properties in a very precise manner.

Safer Polyurethane Foams with Cyclic Carbonates

Polyurethanes (PUs) are a class of materials usually synthesized from isocyanates, diols, and water. Water is essential for producing carbon dioxide (CO₂ ) which is used for the self-blowing of the foams. Due to safety concerns with the production of isocyanates, alternative chemistries have been evaluated and cyclic carbonate systems have shown great promise. In a recent advancement by Bourguignon, Grignard, and Detrembleur, a cyclic carbonate and diamine system is capable of generating CO₂ for self-blowing through hydrolysis of the carbonate-based monomer. The authors demonstrate that with a simple variation of the diamine monomer a wide range of physical and thermo-mechanical properties were achievable. This work represents a significant step towards safer and more environmentally friendly PUs.

Influence of Phosphorus Structures and Their Oxidation States on Flame-Retardant Properties of Polyhydroxyurethanes

This article focuses on the synthesis of polyhydroxyurethane (PHU) materials containing novel phosphorus flame retardants (FR). Four different phosphorus compounds were grafted onto cyclic carbonate: 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO), diethyl phosphite (DEP), diphenyl phosphite (DPP) and dibenzo[d,f][1,3,2]dioxaphosphepine 6-oxide (BPPO). Thus, three novel phosphorus reactive cyclic carbonates which have never been reported so far were synthetized. Phosphorus FR containing PHU materials were characterized by FTIR to evidence the total conversion of the cyclic carbonate. Moreover, the gel contents up to 80% confirmed the formation of the polymer network. Then, the thermal stability and the flame-retardant properties were investigated by thermogravimetric analyses, cone calorimeter and pyrolysis combustion flow calorimeter. The mode of action of phosphorus compounds, depending on the oxidation state, was especially highlighted. Phosphonate (+III) provided better action in a condensed phase than phosphinate thanks to a more efficient char formation. Among phosphonates, differences were observed in terms of char-formation rate and expansion. DEP provided the best flame-retardant properties, with a reduction of 76% of pHRR with 2 wt% of phosphorus in cone calorimeter analysis. Therefore, this article highlighted the different modes of action of phosphorus flame retardants, depending on the oxidation state of phosphorus, in PHU materials.

Recent Progress of Non-Isocyanate Polyurethane Foam and Their Challenges

Polyurethane foams (PUFs) are a significant group of polymeric foam materials. Thanks to their outstanding mechanical, chemical, and physical properties, they are implemented successfully in a wide range of applications. Conventionally, PUFs are obtained in polyaddition reactions between polyols, diisoycyanate, and water to get a CO₂ foaming agent. The toxicity of isocyanate has attracted considerable attention from both scientists and industry professionals to explore cleaner synthesis routes for polyurethanes excluding the use of isocyanate. The polyaddition of cyclic carbonates (CCs) and polyfunctional amines in the presence of an external blowing agent or by self-blowing appears to be the most promising route to substitute the conventional PUFs process and to produce isocyanate-free polyurethane foams (NIPUFs). Especially for polyhydroxyurethane foams (PHUFs), the use of a blowing agent is essential to regenerate the gas responsible for the creation of the cells that are the basis of the foam. In this review, we report on the use of different blowing agents, such as Poly(methylhydrogensiloxane) (PHMS) and liquid fluorohydrocarbons for the preparation of NIPUFs. Furthermore, the preparation of NIPUFs using the self-blowing technique to produce gas without external blowing agents is assessed. Finally, various biologically derived NIPUFs are presented, including self-blown NIPUFs and NIPUFs with an external blowing agent.

Passive Daytime Radiative Cooling by Thermoplastic Polyurethane Wrapping Films with Controlled Hierarchical Porous Structures

Current research has focused on effective solutions to mitigate global warming and the accelerating greenhouse gas emissions. Compared to most cooling methods requiring energy and resources, passive daytime radiative cooling (PDRC) technology offers excellent energy savings as it requires no energy consumption. However, existing PDRC materials encounter unprecedented problems such as complex structures, low flexibility, and performance degradation after stretching. Thus, this study reports a porous structured thermoplastic polyurethane (TPU) film with bimodal pores to produce high-efficiency PDRC with efficient solar scattering using a simple process. The TPU film exhibited an adequately high solar reflectivity of 0.93 and an emissivity of 0.90 in the atmospheric window to achieve an ambient cooling of 5.6 °C at midday under a solar intensity of 800 W m^-2 . Thus, the highly elastic and flexible TPU film was extremely suitable for application on objects with complex shapes. The radiative cooling performance of 3D-printed models covered with these TPU films demonstrated their superior indoor cooling efficiency compared to commercial white paint (8.76 °C). Thus, the proposed design of high-efficiency PDRC materials is applicable in various urban infrastructural objects such as buildings and vehicles.

Water-Induced Self-Blown Non-Isocyanate Polyurethane Foams

For 80 years, polyisocyanates and polyols were central building blocks for the industrial fabrication of polyurethane (PU) foams. By their partial hydrolysis, isocyanates release CO₂ that expands the PU network. Substituting this toxic isocyanate-based chemistry by a more sustainable variant-that in situ forms CO₂ by hydrolysis of a comonomer-is urgently needed for producing greener cellular materials. Herein, we report a facile, up-scalable process, potentially compatible to existing infrastructures, to rapidly prepare water-induced self-blown non-isocyanate polyurethane (NIPU) foams. We show that formulations composed of poly(cyclic carbonate)s and polyamines furnish rigid or flexible NIPU foams by partial hydrolysis of cyclic carbonates in the presence of a catalyst. By utilizing readily available low cost starting materials, this simple but robust process gives access to greener PU foams, expectedly responding to the sustainability demands of many sectors.

Non-Isocyanate Polyurethane Bio-Foam with Inherent Heat and Fire Resistance

Polyurethanes (PUs) are versatile and widespread, particularly as flexible and rigid foams. To avoid isocyanates and other toxic reagents required for synthesis, such as phosgene, alternative synthetic routes have been utilized to produce non-isocyanate polyurethanes (NIPUs). A thermally and flame-resistant rigid NIPU was produced from environmentally benign and bio-sourced ingredients, requiring no catalyst or solvents. A foamed structure was obtained by the addition of glutaraldehyde and four different carboxylic acids: malic acid, maleic acid, citric acid, and aconitic acid. The resulting morphology, thermal degradation, and flame resistance of each foam were compared. The properties vary with each carboxylic acid used, but in each case, peak thermal degradation and peak heat release are postponed by >100 °C compared to commercial rigid PU foam. Furthermore, in a butane torch test, NIPU foams exhibit an 80% higher remaining mass and a 75% reduction in afterburn time, compared to commercial polyurethane. This bio-based polyurethane eliminates the hazards of traditional PUs, while imparting inherent thermal stability and flame resistance uncharacteristic of conventional foams.

Synthesis and properties of high performance thermoplastic polycarbonate polyurethane elastomers through a non-isocyanate route

Thermoplastic polycarbonate polyurethane elastomers (TPCUEs) are synthesized through a solvent-free non-isocyanate melt polycondensation route. The route starts with the synthesis of 1,6-bis(hydroxyethyloxycarbonylamino)hexane (BHCH) from ethylene carbonate and 1,6-hexanediamine, and then the TPCUEs are prepared by the melt polycondensation of BHCH and polycarbonate diols (PCDLs). The TPCUEs are characterized by GPC, FT-IR, ¹H NMR, XRD, AFM, DSC, TGA and tensile testing. The TPCUEs prepared have linear structures and high molecular weights, with Mn over 3.0 × 10⁴ g mol^-1. And these TPCUEs exhibit excellent thermal and mechanical properties, with T _g ranging from -18 to -1 °C, T _m ranging from 93 to 122 °C, T _d,5% over 240 °C, tensile strength between 28.1-47.3 Mpa, elongation at break above 1000%, Young's modulus between 13.8-32.7 Mpa and resilience at 200% fixed-length between 70-90%, which makes them a promising alternative to products synthesized through the isocyanate route. In addition, the effects of the hard segment contents and the molecular weights of soft segment on the properties of TPCUEs are researched.

Synthesis and properties of foams from a blend of vegetable oil based polyhydroxyurethane and epoxy resin

This article aims to highlight the synthesis of foams from a blend of hydroxyurethane of castor oil and epoxy resin. An epoxidized castor oil of 4% oxirane oxygen was first converted to cyclic carbonate of castor oil at 120°C, 1 atm CO2 pressure and then it was reacted with three different aliphatic diamines to yield amine terminated Polyhydroxyurethane (PHU). Foams were prepared in a metal mould from the blend of PHU, epoxy resin, epoxy hardener and polymethylhydrogensiloxane blowing agent which releases hydrogen gas upon reaction with amine. FTIR and 1H NMR of cyclic carbonate of castor oil and PHU of castor oil were done to confirm their chemical structures. Optical microscopy and scanning electron microscopy of foams was done to assess their cellular morphology along with DSC and TGA to evaluate their thermal properties. Both flexible and rigid type of foams were synthesised in this study. Resilience of flexible foams was inspected using a ball rebound test and compression-recovery test while thermal insulation property was checked by measuring thermal conductivity, thermal diffusivity and R-values of rigid foams from heat transfer study using a heat transfer apparatus.

Nanocomposites of Polyhydroxyurethane with POSS Microdomains: Synthesis via Non-Isocyanate Approach, Morphologies and Reprocessing Properties

In this contribution, we reported the synthesis of a novel trifunctional POSS cyclic carbonate [POSS-3(5CC)]. With a difunctional five-member cyclic carbonate and a trifunctional polyetheramine as the precursor, the nanocomposites of polyhydroxyurethane (PHU) with POSS were synthesized. Transmission electron microscopy (TEM) showed that the nanocomposites of PHUs with POSS were microphase-separated; the spherical POSS microdomains via POSS-POSS interactions were generated with the size of 20~40 nm in diameter. After the introduction of POSS microdomains, the nanocomposites displayed improved thermal and mechanical properties. More importantly, the nanocomposites still displayed the reprocessing properties of vitrimers.

Divergent Aminolysis Approach for Constructing Recyclable Self-Blown Nonisocyanate Polyurethane Foams

We report an approach to fabricate self-blown nonisocyanate polyurethane (NIPU) foams by capitalizing on the divergent chemistries of amines with cyclic carbonates─creating the polymer network─and thiolactone─delivering in situ a thiol that generates the blowing agent (CO₂) by reaction with a cyclic carbonate. Multiple linkages (hydroxyurethanes, thioethers, and amides) are created within the polymer network by this domino process. This one-pot methodology furnishes flexible to rigid foams with open-cell morphology at moderate temperature. The foams are easily repurposed into films or structural composites by thermal treatment, showing the first example of recyclable NIPU foams. Remarkably, both the formation and the recycling of the thermoset foams do not necessarily require the use of a catalyst. This facile and robust process is opening new avenues for designing more sustainable PU foams and offers new end-of-life options by facile material repurposing.

Cascade (Dithio)Carbonate Ring Opening Reactions for Self-Blowing Polyhydroxythiourethane Foams

Polyurethane (PU) foams are very common materials that have found many applications over the years. Their use is constantly improving due to their unique physical properties and easy blowing which does not require the addition of a blowing agent. Greener routes have been explored in the recent years to replace isocyanates. One of the most promising routes is leading to Polyhydroxyurethanes (PHU). However, with PHUs, external blowing agent are usually required to obtain a foam. Thus, our work focuses on PHU foam synthesis using in situ reaction to produce NIPU foam. Hence, the aminolysis of thiocyclic carbonate triggers Pearson reaction between released thiols and cyclic carbonates which serves as a chemical blowing agent. This article is protected by copyright. All rights reserved.

Recent Advances in Fabrication of Non-Isocyanate Polyurethane-Based Composite Materials

Polyurethanes (PUs) are a significant group of polymeric materials that, due to their outstanding mechanical, chemical, and physical properties, are used in a wide range of applications. Conventionally, PUs are obtained in polyaddition reactions between diisocyanates and polyols. Due to the toxicity of isocyanate raw materials and their synthesis method utilizing phosgene, new cleaner synthetic routes for polyurethanes without using isocyanates have attracted increasing attention in recent years. Among different attempts to replace the conventional process, polyaddition of cyclic carbonates (CCs) and polyfunctional amines seems to be the most promising way to obtain non-isocyanate polyurethanes (NIPUs) or, more precisely, polyhydroxyurethanes (PHUs), while primary and secondary –OH groups are being formed alongside urethane linkages. Such an approach eliminates hazardous chemical compounds from the synthesis and leads to the fabrication of polymeric materials with unique and tunable properties. The main advantages include better chemical, mechanical, and thermal resistance, and the process itself is invulnerable to moisture, which is an essential technological feature. NIPUs can be modified via copolymerization or used as matrices to fabricate polymer composites with different additives, similar to their conventional counterparts. Hence, non-isocyanate polyurethanes are a new class of environmentally friendly polymeric materials. Many papers on the matter above have been published, including both original research and extensive reviews. However, they do not provide collected information on NIPU composites fabrication and processing. Hence, this review describes the latest progress in non-isocyanate polyurethane synthesis, modification, and finally processing. While focusing primarily on the carbonate/amine route, methods of obtaining NIPU are described, and their properties are presented. Ways of incorporating various compounds into NIPU matrices are characterized by the role of PHU materials in copolymeric materials or as an additive. Finally, diverse processing methods of non-isocyanate polyurethanes are presented, including electrospinning or 3D printing.

Recent Developments in Lignin- and Tannin-Based Non-Isocyanate Polyurethane Resins for Wood Adhesives—A Review

This review article aims to summarize the potential of using renewable natural resources, such as lignin and tannin, in the preparation of NIPUs for wood adhesives. Polyurethanes (PUs) are extremely versatile polymeric materials, which have been widely used in numerous applications, e.g., packaging, footwear, construction, the automotive industry, the lighting industry, insulation panels, bedding, furniture, metallurgy, sealants, coatings, foams, and wood adhesives. The isocyanate-based PUs exhibit strong adhesion properties, excellent flexibility, and durability, but they lack renewability. Therefore, this study focused on the development of non-isocyanate polyurethane lignin and tannin resins for wood adhesives. PUs are commercially synthesized using polyols and polyisocyanates. Isocyanates are toxic, costly, and not renewable; thus, a search of suitable alternatives in the synthesis of polyurethane resins is needed. The reaction with diamine compounds could result in NIPUs based on lignin and tannin. The research on bio-based components for PU synthesis confirmed that they have good characteristics as an alternative for the petroleum-based adhesives. The advantages of improved strength, low curing temperatures, shorter pressing times, and isocyanate-free properties were demonstrated by lignin- and tannin-based NIPUs. The elimination of isocyanate, associated with environmental and human health hazards, NIPU synthesis, and its properties and applications, including wood adhesives, are reported comprehensively in this paper. The future perspectives of NIPUs’ production and application were also outlined.

Synthesis and structural characterization of bio-based bis(cyclic carbonate)s for the preparation of non-isocyanate polyurethanes

Full chemical structure characterization of cyclic carbonates from diepoxides synthesized using sustainable bio-based polyols with different molecular weights and carbon dioxide.

Surface Properties of Poly(Hydroxyurethane)s Based on Five-Membered Bis-Cyclic Carbonate of Diglycidyl Ether of Bisphenol A

Poly(hydroxyurethane)s (PHU) are alternatives for conventional polyurethanes due to the use of bis-cyclic dicarbonates and diamines instead of harmful and toxic isocyanates. However, the surface properties of poly(hydroxyurethane)s are not well known. In this work, we focus on the analysis of the surface properties of poly(hydroxyurethane) coatings. Poly(hydroxyurethane)s were obtained by a catalyst-free method from commercially available carbonated diglycidyl ether of bisphenol A (Epidian 6 epoxy resins) and various diamines: ethylenediamine, trimethylenediamine, putrescine, hexamethylenediamine, 2,2,4(2,4,4)-trimethyl-1,6-hexanediamine, m-xylylenediamine, 1,8-diamino-3,6-dioxaoctane, 4,7,10-trioxa-1,13-tridecanediamine, and isophorone diamine, using a non-isocyanate route. The structures of the obtained polymers were confirmed by FT-IR, ¹H NMR and ¹³C NMR spectroscopy, and thermogravimetric (TGA) and differential scanning calorimetry (DSC) analyses were performed. The rheological characteristic of the obtained polymers is presented. The static contact angles of water, diidomethane, and formamide, deposited on PHU coatings, were measured. From the measured contact angles, the surface free energy was calculated using two different approaches: Owens-Wendt and van Oss-Chaudhury-Good. Moreover, the wetting envelopes of PHU coatings were plotted, which enables the prediction of the wetting effect of various solvents. The results show that in the investigated coatings, a mainly dispersive interaction occurs.

Water-Borne Isocyanate-Free Polyurethane Hydrogels with Adaptable Functionality and Behavior

Polyurethane hydrogels are attractive materials finding multiple applications in various sectors of prime importance; however, they are still prepared by the toxic isocyanate chemistry. Herein the facile and direct preparation in water at room temperature of a large palette of anionic, cationic, or neutral polyurethane hydrogels by a non-isocyanate route from readily available diamines and new hydrosoluble polymers bearing cyclic carbonates is reported. The latter are synthesized by free radical polymerization of glycerin carbonated methacrylate with water-soluble comonomers. The hydrogel formation is studied at different pH and its influence on the gel time and storage modulus is investigated. Reinforced hydrogels are also constructed by adding CaCl₂ to the formulation that in-situ generates CaCO₃ particles. Thermoresponsive hydrogels are also prepared from new thermoresponsive cyclic carbonate bearing polymers. This work demonstrates that a multitude of non-isocyanate polyurethane hydrogels are easily accessible under mild conditions without any catalyst, opening new perspectives in the field.

Chemo- and Regioselective Additions of Nucleophiles to Cyclic Carbonates for the Preparation of Self-Blowing Non-Isocyanate Polyurethane Foams

Polyurethane (PU) foams are indisputably daily essential materials found in many applications, notably for comfort (for example, matrasses) or energy saving (for example, thermal insulation). Today, greener routes for their production are intensively searched for to avoid the use of toxic isocyanates. An easily scalable process for the simple construction of self-blown isocyanate-free PU foams by exploiting the organocatalyzed chemo- and regioselective additions of amines and thiols to easily accessible cyclic carbonates is described. These reactions are first validated on model compounds and rationalized by DFT calculations. Various foams are then prepared and characterized in terms of morphology and mechanical properties, and the scope of the process is illustrated by modulating the composition of the reactive formulation. With impressive diversity and accessibility of the main components of the formulations, this new robust and solvent-free process could open avenues for construction of more sustainable PU foams, and offers the first realistic alternative to the traditional isocyanate route.

Effects of surfactants on mechanical and thermal properties of soy-based polyurethane foams

Polyurethane foams are widely used for insulation applications due to their high insulation properties as compared to conventional materials such as extruded polystyrene foam and mineral wool. In this study, soy-based polyurethane foams were prepared using five different surfactants while keeping other components such as soy-based polyol, diisocyanate, catalyst, and blowing agent (water) constant. Prepared samples were tested for mechanical and thermal properties to evaluate the effect of different surfactants used in varying quantities. The morphology of the foam samples was observed using a scanning electron microscope. Seventeen fold reduction in the cell size was observed with an increase in the amount of surfactant from 0.5 to 5.0 g. Samples with higher amounts of surfactant also exhibited a higher number of closed cells. Better thermal insulation was observed for samples with 2.0 and 5.0 g of surfactant as compared to samples with 0.5 g of surfactant. A similar trend was observed in the mechanical strength, moisture absorbance, and density of the fabricated foam samples.

Hybrid Poly(hydroxy urethane)s: Folded-Sheet Morphology and Thermoreversible Adhesion

Hybrid poly(hydroxy urethane)s (PHUs) are synthesized by copolymerizing aromatic/alicyclic cyclic carbonates with a polyether amine via addition polymerization. They result into polymers with an average molecular weight of 10 kDa and exhibit solubility in common organic solvents. The hybrid PHUs display T g up to 18 °C. PHUs are enriched with multiple H-bonded interactions and they are assessed using temperature-dependent 1H NMR and Fourier-transform infrared studies. PHUs possess folded-sheet morphology with nanogap between folds and nanowidth between chains. The secondary interactions bestow thermoreversible property to PHUs, and they display good adhesion to both polar (Al-Al) and nonpolar (HDPE-HDPE) substrates. Hybrid PHUs show improved optical transparency compared to homo PHUs. The PHUs are thermally stable up to 250 °C.

Non-isocyanate urethane linkage formation using l-lysine residues as amine sources

Bio-based polyurethane materials are broadly applied in medicine as drug delivery systems. Nevertheless, their synthesis comprises the use of petroleum-based toxic amines, isocyanates and polyols, and their biocompatibility or functionalization is limited. Therefore, the use of lysine residues as amine sources to create non-isocyanate urethane (NIU) linkages was investigated. Therefore, a five-membered biscyclic carbonate (BCC) was firstly synthetized and reacted with a protected lysine, a tripeptide and a heptapeptide to confirm the urethane linkage formation with lysine moiety and to optimize reaction conditions. Afterwards, the reactions between BCC and a model protein, elastin-like protein (ELP), and β-Lactoglobulin (BLG) obtained from whey protein, respectively, were performed. The synthesized protein materials were structural, thermally and morphologically characterized to confirm the urethane linkage formation. The results demonstrate that using both simple and more complex source of amines (lysine), urethane linkages were effectively achieved. This pioneering approach opens the possibility of using proteins to develop non-isocyanate polyurethanes (NIPUs) with tailored properties.

Polymers Based on Cyclic Carbonates as Trait d'Union Between Polymer Chemistry and Sustainable CO2 Utilization

Given the large amount of anthropogenic CO₂ emissions, it is advantageous to use CO₂ as feedstock for the fabrication of everyday products, such as fuels and materials. An attractive way to use CO₂ in the synthesis of polymers is by the formation of five-membered cyclic organic carbonate monomers (5CCs). The sustainability of this synthetic approach is increased by using scaffolds prepared from renewable resources. Indeed, recent years have seen the rise of various types of carbonate syntheses and applications. 5CC monomers are often polymerized with diamines to yield polyhydroxyurethanes (PHU). Foams are developed from this type of polymers; moreover, the additional hydroxyl groups in PHU, absent in classical polyurethanes, lead to coatings with excellent adhesive properties. Furthermore, carbonate groups in polymers offer the possibility of post-functionalization, such as curing reactions under mild conditions. Finally, the polarity of carbonate groups is remarkably high, so polymers with carbonates side-chains can be used as polymer electrolytes in batteries or as conductive membranes. The target of this Review is to highlight the multiple opportunities offered by polymers prepared from and/or containing 5CCs. Firstly, the preparation of several classes of 5CCs is discussed with special focus on the sustainability of the synthetic routes. Thereafter, specific classes of polymers are discussed for which the use and/or presence of carbonate moieties is crucial to impart the targeted properties (foams, adhesives, polymers for energy applications, and other functional materials).

En route to CO2-containing renewable materials: catalytic synthesis of polycarbonates and non-isocyanate polyhydroxyurethanes derived from cyclic carbonates

The strategies and challenges in the preparation of fully renewable materials prepared from CO₂ and biomass enabled by catalysis are presented.