Morphology and molecular dynamics investigation of PDMS adsorbed on titania nanoparticles: Effects of polymer molecular weight

A Comparative Study of the Biodurability and Persistence of Gold, Silver and Titanium Dioxide Nanoparticles Using the Continuous Flow through System

The potential for nanoparticles to cause harm to human health and the environment is correlated with their biodurability in the human body and persistence in the environment. Dissolution testing serves to predict biodurability and nanoparticle environmental persistence. In this study, dissolution testing using the continuous flow through system was used to investigate the biodurability and persistence of gold nanoparticles (AuNPs), silver nanoparticles (AgNPs) and titanium dioxide nanoparticles (TiO₂ NPs) in five different simulated biological fluids and two synthetic environmental media to predict their behaviour in real life situations. This study examined the physicochemical properties and agglomeration state of gold, silver and titanium dioxide nanoparticles before and after dissolution tests using three different techniques (UV-vis, XRD and TEM). The UV-vis spectra revealed that all three nanoparticles shifted to higher wavelengths after being exposed to simulated fluids. The titanium powder was found to be mixed with both rutile and anatase, according to XRD examination. The average diameter of gold nanoparticles was 14 nm, silver nanoparticles were 10 nm and titanium dioxide nanoparticles were 25 nm, according to TEM images. The gold and silver nanoparticles were observed to be spherical, but the titanium dioxide nanoparticles were irregular in shape, with some being spherical. The level of dissolved nanoparticles in simulated acidic media was higher in magnitude compared to that dissolved in simulated alkaline media. The results obtained via the continuous flow through dissolution system also displayed very significant dissolution rates. For TiO₂ NPs the calculated half-times were in the range of 13-14 days, followed by AuNPs ranging between 4-12 days, significantly longer if compared to the half-times of AgNPs ranging between 2-7 days. AuNPs and TiO₂ NPs were characterized by low dissolution rates therefore are expected to be (bio)durable in physiological surroundings and persistent in the environment thus, they might impose long-term effects on humans and the environment. In contrast, AgNPs have high dissolution rates and not (bio)durable and hence may cause short-term effects. The results suggest a hierarchy of biodurability and persistence of TiO₂ NPs > AuNPs > AgNPs. It is recommended that nanoparticle product developers should follow the test guidelines stipulated by the OECD to ensure product safety for use before it is taken to the market.

Correlating the Interfacial Polar-Phase Structure to the Local Chemistry in Ferroelectric Polymer Nanocomposites by Combined Scanning Probe Microscopy

Ferroelectric polymer nanocomposites possess exceptional electric properties with respect to the two otherwise uniform phases, which is commonly attributed to the critical role of the matrix-particle interfacial region. However, the structure-property correlation of the interface remains unestablished, and thus, the design of ferroelectric polymer nanocomposite has largely relied on the trial-and-error method. Here, a strategy that combines multi-mode scanning probe microscopy-based electrical characterization and nano-infrared spectroscopy is developed to unveil the local structure-property correlation of the interface in ferroelectric polymer nanocomposites. The results show that the type of surface modifiers decorated on the nanoparticles can significantly influence the local polar-phase content and the piezoelectric effect of the polymer matrix surrounding the nanoparticles. The strongly coupled polar-phase content and piezoelectric effect measured directly in the interfacial region as well as the computed bonding energy suggest that the property enhancement originates from the formation of hydrogen bond between the surface modifiers and the ferroelectric polymer. It is also directly detected that the local domain size of the ferroelectric polymer can impact the energy level and distribution of charge traps in the interfacial region and eventually influence the local dielectric strength.

Effect of Micro- and Nano-Lignin on the Thermal, Mechanical, and Antioxidant Properties of Biobased PLA-Lignin Composite Films

Bio-based poly(lactic acid) (PLA) composite films were produced using unmodified soda micro- or nano-lignin as a green filler at four different contents, between 0.5 wt% and 5 wt%. The PLA-lignin composite polymers were synthesized by solvent casting to prepare a masterbatch, followed by melt mixing. The composites were then converted into films, to evaluate the effect of lignin content and size on their physicochemical and mechanical properties. Differential scanning calorimetry (DSC), supported by polarized light microscopy (PLM), infrared spectroscopy (FTIR-ATR), X-ray diffraction (XRD), and transmission electron microscopy (TEM) were employed to investigate the PLA crystallization and the interactions with Lignin (L) and Nanolignin (NL). The presence of both fillers (L and NL) had a negligible effect on the glass transition temperature (chain diffusion). However, it resulted in suppression of the corresponding change in heat capacity. This was indicative of a partial immobilization of the PLA chains on the lignin entities, due to interfacial interactions, which was slightly stronger in the case of NL. Lignin was also found to facilitate crystallization, in terms of nucleation; whereas, this was not clear in the crystalline fraction. The addition of L and NL led to systematically larger crystallites compared with neat PLA, which, combined with the higher melting temperature, provided indications of a denser crystal structure in the composites. The mechanical, optical, antioxidant, and surface properties of the composite films were also investigated. The tensile strength and Young's modulus were improved by the addition of L and especially NL. The UV-blocking and antioxidant properties of the composite films were also enhanced, especially at higher filler contents. Importantly, the PLA-NL composite films constantly outperformed their PLA-L counterparts, due to the finer dispersion of NL in the PLA matrix, as verified by the TEM micrographs. These results suggest that bio-based and biodegradable PLA films filled with L, and particularly NL, can be employed as competitive and green alternatives in the food packaging industry.

Polymer Nanocomposite Dielectrics: Understanding the Matrix/Particle Interface

Polymer nanocomposite dielectrics possess exceptional electric properties that are absent in the pristine dielectric polymers. The matrix/particle interface in polymer nanocomposite dielectrics is suggested to play decisive roles on the bulk material performance. Herein, we present a critical overview of recent research advances and important insights in understanding the matrix/particle interfacial characteristics in polymer nanocomposite dielectrics. The primary experimental strategies and state-of-the-art characterization techniques for resolving the local property-structure correlation of the matrix/particle interface are dissected in depth, with a focus on the characterization capabilities of each strategy or technique that other approaches cannot compete with. Limitations to each of the experimental strategy are evaluated as well. In the last section of this Review, we summarize and compare the three experimental strategies from multiple aspects and point out their advantages and disadvantages, critical issues, and possible experimental schemes to be established. Finally, the authors' personal viewpoints regarding the challenges of the existing experimental strategies are presented, and potential directions for the interface study are proposed for future research.

Titanium Dioxide/Polysiloxane Composites: Preparation, Characterization and Study of Their Color Stability Using Thermochromic Pigments

In order to improve thermomechanical, antibacterial and temperature-controlled color-response performance of polydimethylsiloxane (PDMS) in maxillofacial prostheses, the incorporation of titania (TiO2) nanoparticles and thermochromic pigments (TCP) into PDMS was examined. The thermal transitions of TiO2/PDMS nanocomposites, investigated by differential scanning calorimetry (DSC), remain almost unaffected, while an increase of the crystallinity of PDMS was recorded in specimens with higher titania concentrations. The incorporation of titania improves the thermal stability, as it was revealed by thermogravimetric analysis (TGA), as well as the tensile properties of the reinforced elastomer. Nanocomposites with 10 wt% titania presented antibacterial activity against Escherichia Coli, leading to 72% reduction of the bacterial colony after 3 h of exposure. Specimens colored with red TCP (0.2 and 0.6 wt%) showed significant color change at a lower temperature (−20 °C) in comparison with that at an ambient temperature, especially at lower TCP concentration (0.2 wt%). Accelerating aging experiments, consisting of repeated cycles of combined exposure to UV-radiation and damp heating, of PDMS colored with TCP showed poor color stability of the specimens, from the first hours of exposure. The addition of titania to polysiloxane specimens works as an opacifier providing a positive effect on the color stability of the examined thermochromic pigment.

Pristine and Poly(Dimethylsiloxane) Modified Multi-Walled Carbon Nanotubes as Supports for Lipase Immobilization

The presented study deals with the fabrication of highly stable and active nanobiocatalysts based on Candida antarctica lipase B (CALB) immobilization onto pristine and poly(dimethylsiloxane) modified MWCNTs. The MWCNTs/PDMS nanocomposites, containing 40 wt.% of the polymer with two molecular weights, were successfully synthesized via adsorption modification. The effect of PDMS chains length on the textural/structural properties of produced materials was studied by means of the nitrogen adsorption–desorption technique, Raman spectroscopy, and attenuated total reflectance Fourier transform infrared spectroscopy. P-MWCNTs and MWCNTs/PDMS nanocomposites were tested as supports for lipase immobilization. Successful deposition of the enzyme onto the surface of P-MWCNTs and MWCNTs/PDMS nanocomposite materials was confirmed mainly using ATR-FTIR spectroscopy. The immobilization efficiency, stability, and catalytic activity of the immobilized enzyme were studied, and the reusability of the produced biocatalytic systems was examined. The presented results demonstrate that the produced novel biocatalysts might be considered as promising materials for biocatalytic applications.

Calorimetric and Dielectric Study of Renewable Poly(hexylene 2,5-furan-dicarboxylate)-Based Nanocomposites In Situ Filled with Small Amounts of Graphene Platelets and Silica Nanoparticles

Poly(hexylene 2,5 furan-dicarboxylate) (PHF) is a relatively new biobased polyester prepared from renewable resources, which is targeted for use in food packaging applications, owing to its great mechanical and gas barrier performance. Since both properties are strongly connected to crystallinity, the latter is enhanced here by the in situ introduction in PHF of graphene nanoplatelets and fumed silica nanoparticles, as well as mixtures of both, at low amounts. For this investigation, we employed Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), X-ray diffraction (XRD) and dielectric spectroscopy (BDS). The fillers were found to improve crystallization in both the rate (increasing Tc) and fraction (CF), which was rationalized via the concept of fillers acting as crystallization agents. This action was found stronger in the case of graphene as compared to silica. BDS allowed the detection of local and segmental dynamics, in particular in PHF for the first time. The glass transition dynamics in both BDS (α relaxation) and DSC (Tg) are mainly dominated by the relatively high CF, whereas in the PHF filled uniquely with silica strong spatial confinement effects due to crystals were revealed. Finally, all samples demonstrated the segmental-like dynamics above Tg, which screens the global chain dynamics (normal mode).

Effects of CNTs on thermal transitions, thermal diffusivity and electrical conductivity in nanocomposites: comparison between an amorphous and a semicrystalline polymer matrix

Two series of polymer nanocomposites (PNCs) based on amorphous styrene-butadiene rubber (SBR) and semicrystalline linear low-density polyethylene (PE) matrices were filled with 2-15 wt% carbon nanotubes (CNT) and were studied by employing calorimetry, dielectric spectroscopy and laser flash analysis. The electrical conductivity, σ, increased with CNT loading and similar values were exhibited for the two matrices, uniquely depending on the concentration of the CNTs, suggesting practically no effects of the crystalline fraction (CF) on σ. For both types of matrix, a fraction of the polymer was found to be immobilized (rigid amorphous fraction, RAF). For the amorphous SBR, the RAF in PNCs originates uniquely from the presence of the filler (RAFfiller up to 0.19 wt). On the other hand, for the semicrystalline PE, the RAF is significantly larger (0.4-0.6 wt) due to the severe contribution of the RAF around the crystals (RAFcrystal). The thermal diffusivity, α, is quite low in both types of PNCs and exhibits higher values in the semicrystalline matrix (PE-based PNCs). Our results suggest that in these PNCs, heat transport mechanisms are activated mainly in the crystalline domains, more so with the additive contribution of the RAFcrystal. In the amorphous SBR-based PNCs, heat transport is facilitated mainly by CNTs, whereas the RAFfiller is found to be a good measure of the thermal resistance behavior of CNT/polymer interphases and consequently, of thermal diffusivity. Direct correlation of the results obtained by the three techniques with each other revealed the systematic dependence of α on the amount of RAF in each matrix; the α(RAF) trends, however, are different for the two matrices. Furthermore, the results suggest that the two RAFs exhibit different structural characteristics, e.g. the RAFcrystal exhibits a more ordered structure than the RAFfiller; this issue is still an open debate in the literature.

Influence of molecular weight on molecular dynamics and dynamic rheology of polypropylene glycol filled with silica

Molecular weight strongly influences the molecular dynamics and rheological responses of nanocomposites, which is far from being well understood. Herein molecular dynamics and rheological behaviors of hydrophilic fumed silica filled unentangled polypropylene glycol (PPG) were investigated as a function of weight averaged molecular weight (M w) of PPG and volume fraction (∅) of silica. It is shown that M w does not affect the glassy layers surrounding the nanoparticles and the segmental dynamics of the mobile PPG phase. On the other hand, the mobile PPG phase in the highly filled nanocomposites exhibits an abnormal "more fragile" to "stronger" transition with increasing M w. The reinforcement and thinning behaviors are stronger in lower-M w nanocomposites with the "more fragile" mobile PPG phase. The results suggest that reinforcement of nanocomposites affects the dynamic fragility of the mobile phase of the matrix.

Nanosilica modified by polydimethylsiloxane depolymerized and chemically bound to nanoparticles or physically bound to unmodified or modified surfaces: Structure and interfacial phenomena

Three polydimethylsiloxanes (PDMS200, PDMS1000, and PDMS12500 with numbers showing the viscosity values dependent on the molecular weight) were used for adsorption (14-95 wt% PDMS) onto unmodified and PDMS-modified (16.7 wt% PDMS using dimethyl carbonate (DMC) as a siloxane bond breaking reagent) nanosilica A-300. The materials were studied using microscopy, infrared spectroscopy, thermodesorption, calorimetry, ethanol and water/ethanol evaporation, nitrogen adsorption-desorption, and quantum chemical methods. The interfacial and temperature behaviors of a PDMS layer at a silica surface depend strongly on the type of bonding to silica particles, molecular weight and content of PDMS. Upon chemical bonding, shorter PDMS200 forms a denser coverage of the silica surface since S_BET diminution is larger and residual free silanols are practically absent (the degree of free silanol substitution Θ > 0.95) in contrast to the reactions with PDMS1000/DMC or PDMS12500/DMC providing Θ = 0.60-0.63 at larger S_BET values. Upon thermal decomposition of the PDMS layer, oxidation/depolymerization desorption gives a greater contribution than pure depolymerization destruction. An increase in the PDMS adsorption layer thickness leads to enhancement of the depolymerization contribution because the oxidation mainly occurs at the top of the layer, but the depolymerization can occur in the total PDMS layer. The adsorption, desorption, and evaporation processes of low-molecular weight probes at a surface of PDMS-modified nanosilica depend strongly on the type of bonding and content of PDMS. Thus, the most effective hydrophobization of nanosilica by PDMS/DMC could be carried out using the shortest polymer giving the shortest PDMS fragments upon the interaction with DMC that is of interest from a practical point of view.

Nanooxide/Polymer Composites with Silica@PDMS and Ceria-Zirconia-Silica@PDMS: Textural, Morphological, and Hydrophilic/Hydrophobic Features

SiO₂@PDMS and CeO₂-ZrO₂-SiO₂@PDMS nanocomposites were prepared and studied using nitrogen adsorption-desorption, Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), measurements of advancing and receding contact angles with water, and microcalorimetry. The pore size distributions indicate that the textural characteristics change after oxide modification by poly(dimethylsiloxane) (PDMS). Composites are characterized by mainly mesoporosity and macroporosity of aggregates of oxide nanoparticles or oxide@PDMS nanoparticles and their agglomerates. The FT-IR spectra show that PDMS molecules cover well the oxide surface, since the intensity of the band of free silanols at 3748 cm^-1 decreases with increasing PDMS concentration and it is absent in the IR spectrum at C _PDMS ≥ 20 wt% that occurs due to the hydrogen bonding of the PDMS molecules to the surface hydroxyls. SEM images reveal that the inter-particle voids are gradually filled and aggregates are re-arranged and increase from 20 to 200 nm in size with the increasing polymer concentration. The highest hydrophobicity (contact angle θ = 140° at C _PDMS = 20-40 wt%) is obtained for the CeO₂-ZrO₂-SiO₂@PDMS nanocomposites. The heat of composite immersion in water shows a tendency to decrease with increasing PDMS concentration.

Dynamic glass transition of the rigid amorphous fraction in polyurethane-urea/SiO2 nanocomposites

We report molecular dynamics in the rigid amorphous fraction (RAF) of the polymer bound at the interfaces with nanoparticles in polymer nanocomposites and calculate the glass transition temperature, T_g, for this bound layer of polymer. We follow the '3-phase-model' for semicrystalline polymers where the polymer matrix consists of the crystalline fraction (CF), the mobile amorphous fraction (MAF) and the RAF. While the amorphous polymer bound by crystallites is completely rigid, neither contributing to the glass transition, nor displaying molecular dynamics, the amorphous polymer bound at the interfaces with filler displays decelerated dynamics, as compared to the bulk polymer. Reports in the literature suggest a discrepancy between T_g values obtained by Differential Scanning Calorimetry (DSC) and by Dielectric Relaxation Spectroscopy (DRS). As a plausible explanation we suggest that DRS results in T_g values taking into account the bound polymer, whereas DSC does not. For this investigation we use semicrystalline polyurethane-urea/SiO₂ nanocomposites and employ, next to DSC and DRS, SEM, SAXS and WAXS for morphological characterization. It is our intention to use DRS as a tool for investigating the RAF.

Filler's impact on structure and physical properties in polyester resin–oxide nanocomposites

Impact of nanosized oxide particles of titania (titanium dioxide, rutile) and silica–titania fumed compound on structure relaxation processes in nanocomposites of an orthophtalic unsaturated styrene cross-linked polyester resin has been experimentally studied using the thermal desorption mass spectroscopy, the dielectric spectroscopy, and the positron annihilation lifetime spectroscopy. All the nanocomposites showed unmonotonous variations in the thermal resistance, the dielectric permittivity and losses, and the annihilation rates for both positrons and ortho-positronium atoms with increasing filler’s loading. The nanoparticle-loading effects can be explained on the assumption that the oxide particles embedded into a cross-linked polyester resin induce rearrangements in its structure. Several mechanisms of particle–polymer interface interaction compete simultaneously and thus promote the alterations in molecular structure of the nanocomposites. The mechanisms may include both chemical and electrostatic fastening of polyester chains and styrene cross-links to the active surface sites, the destruction of the styrene cross-links, and redistribution of electron density in polymers. The features of the loading effects observed in the different nanocomposites can be ascribed to distinctions in both of active surface sites and intrinsic dielectric properties of the filling oxide particles.

Preparation and characterization of core-shell oil absorption materials stabilized by modified fumed silica

The core-shell oil absorption material (OAM) with fumed silica shell was achieved from Pickering polymerization. The modified fumed silica wall could well stabilize both Pickering emulsion and Pickering polymerization. The particle size of encapsulated OAMs decreased with the increasing concentration of fumed silica and remained unchanged when the concentration was more than 1 wt.%. This fumed silica shell had little effect on the oil absorption rate of OAM. The importance was that the shell reversed the surface property and improved the alkali resistance of OAM. We believe that our core-shell OAMs could reach the self-healing ability of the oil well cement.

Dimethylsilanone Generation from Pyrolysis of Polysiloxanes Filled with Nanosized Silica and Ceria/Silica

Temperature-programmed desorption mass spectrometry (TPD MS) was used to study the pyrolysis of PDMS and its composites with nanosized silica and ceria/silica. The results suggest that the elusive organosilicon compound, dimethylsilanone, is generated from PDMS over a broad temperature range (in some cases starting at 70 °C). The presence of nano-oxides catalyzes this process. Ions characteristic of the fragmentation of dimethylsilanone under electron ionization are assigned with the aid of DFT structure calculations. Possible reaction mechanisms for dimethylsilanone generation are discussed in the context of the calculated kinetic parameters. Observed accompanying products of PDMS pyrolysis, such as tetramethylcyclodisiloxane and hexamethylcyclotrisiloxane, indicate that multiple channels are involved in the dimethylsilanone release.

Interfacial phenomena at a surface of individual and complex fumed nanooxides

Investigations of interfacial and temperature behaviors of nonpolar and polar adsorbates interacting with individual and complex fumed metal or metalloid oxides (FMO), initial and subjected to various treatments or chemical functionalization and compared to such porous adsorbents as silica gels, precipitated silica, mesoporous ordered silicas, filled polymeric composites, were analyzed. Complex nanooxides include core-shell nanoparticles, CSNP (50-200nm in size) with titania or alumina cores and silica or alumina shells in contrast to simple and smaller nanoparticles of individual FMO. CSNP could be destroyed under high-pressure cryogelation (HPCG) or mechanochemical activation (MCA). These treatments affect the structure of aggregates of nanoparticles and agglomerates of aggregates, resulting in their becoming more compacted. The analysis shows that complex FMO could be more sensitive to external actions than simple nanooxides such as fumed silica. Any treatment of 'soft' FMO affects the interfacial and temperature behaviors of polar and nonpolar adsorbates. Rearrangement of secondary particles and surface functionalization affects the freezing-melting point depression of adsorbates. For some adsorbates, open hysteresis loops became readily apparent in adsorption-desorption isotherms. Clustering of adsorbates bound in textural pores in aggregates of nanoparticles (i.e., voids between nanoparticles in secondary structures) causes reduced changes in enthalpy during phase transitions (freezing, fusion, evaporation). Freezing point depression and melting point elevation cause significant hysteresis freezing-melting effects for adsorbates bound to FMO in the textural pores. Relaxation phenomena for both low- and high-molecular weight adsorbates or filled polymeric composites are affected by the morphology of primary particles, structural organization of secondary particles of differently treated or functionalized FMO, content of adsorbates, co-adsorption order, and temperature.

Network dynamics in nanofilled polymers

It is well accepted that adding nanoparticles (NPs) to polymer melts can result in significant property improvements. Here we focus on the causes of mechanical reinforcement and present rheological measurements on favourably interacting mixtures of spherical silica NPs and poly(2-vinylpyridine), complemented by several dynamic and structural probes. While the system dynamics are polymer-like with increased friction for low silica loadings, they turn network-like when the mean face-to-face separation between NPs becomes smaller than the entanglement tube diameter. Gel-like dynamics with a Williams-Landel-Ferry temperature dependence then result. This dependence turns particle dominated, that is, Arrhenius-like, when the silica loading increases to ∼31 vol%, namely, when the average nearest distance between NP faces becomes comparable to the polymer's Kuhn length. Our results demonstrate that the flow properties of nanocomposites are complex and can be tuned via changes in filler loading, that is, the character of polymer bridges which 'tie' NPs together into a network.