Grafting of polystyrene onto reduced graphene oxide by emulsion polymerization for dielectric polymer composites: High dielectric constant and low dielectric loss tuned by varied grafting amount of polystyrene

From waste to energy storage: post-consumer waste expanded polystyrene/rGO composite as a high performance self-standing electrode for coin cell supercapacitors

This research work aims to explore the potential usage of post-consumer waste expanded polystyrene (EPS) for the fabrication of self-standing electrodes by incorporating reduced graphene oxide (rGO) into it via a facile cost-effective mechanical mixing process. The π-π interaction between the expanded polystyrene and rGO is evidenced from FT-IR and Raman analysis. The elevated thermal stability of the EPS/rGO composite from thermogravimetric analysis (TGA) further confirms the interconnection between the rGO and EPS. This π-π stacking interaction between the rGO and the polystyrene molecules present in the polymer matrix enable the composite material to be interconnected throughout which is beneficial for the charge transport process. The symmetric coin cell supercapacitor fabricated using the EPS/rGO composite electrode can be operated with a high operating voltage of 1.6 V in aqueous KOH and Na2SO4 electrolytes. The devices fabricated with KOH and Na2SO4 electrolytes deliver an areal capacitance of 11.9 mF cm-2 and 10 mF cm-2 at the discharge current density of 0.1 mA cm-2. Further, the devices fabricated with the KOH and Na2SO4 electrolytes demonstrated remarkable rate capability of 87.1% and 99.5% after 10 000 continuous charge discharge cycles. This facile method of preparation without consuming energy or polluting the environment is a novel approach which can be scaled-up to large-scale fabrication of self-standing plastic electrodes for low-cost energy storage applications.

Energy Storage Performance of Polymer-Based Dielectric Composites with Two-Dimensional Fillers

Dielectric capacitors have garnered significant attention in recent decades for their wide range of uses in contemporary electronic and electrical power systems. The integration of a high breakdown field polymer matrix with various types of fillers in dielectric polymer nanocomposites has attracted significant attention from both academic and commercial sectors. The energy storage performance is influenced by various essential factors, such as the choice of the polymer matrix, the filler type, the filler morphologies, the interfacial engineering, and the composite structure. However, their application is limited by their large amount of filler content, low energy densities, and low-temperature tolerance. Very recently, the utilization of two-dimensional (2D) materials has become prevalent across several disciplines due to their exceptional thermal, electrical, and mechanical characteristics. Compared with zero-dimensional (0D) and one-dimensional (1D) fillers, two-dimensional fillers are more effective in enhancing the dielectric and energy storage properties of polymer-based composites. The present review provides a comprehensive overview of 2D filler-based composites, encompassing a wide range of materials such as ceramics, metal oxides, carbon compounds, MXenes, clays, boron nitride, and others. In a general sense, the incorporation of 2D fillers into polymer nanocomposite dielectrics can result in a significant enhancement in the energy storage capability, even at low filler concentrations. The current challenges and future perspectives are also discussed.

Facile fabrication of polystyrene particles/graphene composites for improved dielectric and thermal properties

In this paper, polystyrene (PS)-based reduced graphene oxide (rGO) composites were prepared by mixing PS latex particles with graphene oxide (GO) and the following in-situ reduction. The structure and morphology of PS/rGO composites were characterized, and the effects of rGO content on the dielectric properties as well as thermal stability of PS/rGO composites were investigated. Results showed that rGO sheets armoured on the surface of PS particles and exhibited well dispersion in the PS matrix after hot compression. The introduction of rGO improved the dielectric properties of the composites remarkably. When rGO content was 0.12 vol%, the dielectric permittivity and breakdown strength of PS/rGO arrived at 6.3 at10² Hz and 107 kV/mm, with 50% and 35.4% enhancement compared to the pristine PS. Furthermore, PS/rGO presented better thermal stability than the pristine PS, but the overlapping of rGO sheets in PS matrix induced the instability of dielectric loss with frequency.

Graphene oxide enhances thermal stability and microwave absorption/regeneration of a porous polymer

Microwave regeneration of adsorbents offers several advantages over conventional regeneration methods; however, its application for microwave transparent adsorbents such as polymers is challenging. In this study, hypercrosslinked polymer/graphene oxide (GO) nanocomposites with large surface area and enhanced microwave absorption ability were synthesized. Polymers of 4, 4´-bis ((chloromethyl)-1, 1´-biphenyl- benzyl chloride) were hypercrosslinked through the Friedel-Crafts reactions. GO sheets were synthesized through the Hummer's method. Nanocomposites with different GO contents (1-8 wt%) were synthesized by solution mixing method. Thermogravimetry analysis revealed a large enhancement in the thermal stability of GO-filled nanocomposites compared to pristine polymer. N₂ adsorption isotherm analysis showed 7% and 10% reduction in BET surface area and total pore volume of the nanocomposite with 8 wt% GO. Compared to the pristine polymer, the dielectric constant and dielectric loss factor increased from 5 to 17 and 0.05-1.6, respectively, for the nanocomposites with 8 wt% GO. Microwave-assisted desorption of toluene from samples revealed more than 160 ºC and 4 times improvement in the desorption temperature and desorption efficiency, respectively, by addition of 4 wt% GO to the polymer. This study showed the important role of GO addition for efficient microwave-assisted regeneration of polymer adsorbents.

Hydroxyl-Terminated Triazine Derivatives Grafted Graphene Oxide for Epoxy Composites: Enhancement of Interfacial and Mechanical Properties

An effective approach to the fabrication of progressive epoxy nanocomposites by the incorporation of hydroxyl-terminated dendrimers functionalized graphene oxide (GO-TCT-Tris) is reported. The relationship between surface grafting, chemical construction, morphology, dispersion, and interfacial interaction as well as the corresponding mechanical properties of the composites were studied in detail. It was shown that hydroxyl-terminated triazine derivatives have been resoundingly bonded onto the GO surface through covalent bonding, which effectively improved the dispersion and compatibility of GO sheets in epoxy resin. The tensile and flexural tests manifested that the GO-TCT-Tris/epoxy composites exhibited greater tensile/flexural strength and modulus than either the pure epoxy or the GO/epoxy composites. For GO-TCT-Tris (0.10 wt%)/epoxy composite, the tensile strength and elastic modulus increased from 63 ± 4 to 89 ± 6 MPa (41.27%) and from 2.8 ± 0.1 to 3.6 ± 0.2 GPa (28.57%), and the flexural strength and modulus increased from 106 ± 5 to 158 ± 6 MPa (49.06%) and from 3.0 ± 0.1 to 3.5 ± 0.2 GPa (16.67%), respectively, compared to the pure epoxy matrix. Moreover, the fractographic analysis also illustrated the ameliorative interfacial interaction between GO-TCT-Tris and epoxy matrix.

Characterization of Reduced and Surface-Modified Graphene Oxide in Poly(Ethylene-co-Butyl Acrylate) Composites for Electrical Applications

Promising electrical field grading materials (FGMs) for high-voltage direct-current (HVDC) applications have been designed by dispersing reduced graphene oxide (rGO) grafted with relatively short chains of poly (n-butyl methacrylate) (PBMA) in a poly(ethylene-co-butyl acrylate) (EBA) matrix. All rGO-PBMA composites with a filler fraction above 3 vol.% exhibited a distinct non-linear resistivity with increasing electric field; and it was confirmed that the resistivity could be tailored by changing the PBMA graft length or the rGO filler fraction. A combined image analysis- and Monte-Carlo simulation strategy revealed that the addition of PBMA grafts improved the enthalpic solubility of rGO in EBA; resulting in improved particle dispersion and more controlled flake-to-flake distances. The addition of rGO and rGO-PBMAs increased the modulus of the materials up to 200% and the strain did not vary significantly as compared to that of the reference matrix for the rGO-PBMA-2 vol.% composites; indicating that the interphase between the rGO and EBA was subsequently improved. The new composites have comparable electrical properties as today's commercial FGMs; but are lighter and less brittle due to a lower filler fraction of semi-conductive particles (3 vol.% instead of 30-40 vol.%).

Carbon-based polymer nanocomposites as dielectric energy storage materials

Nanostructured polymeric materials based on conductive nanofillers have promising applications in the energy storage field owing to the extraordinary characteristics of the nanofillers. Conductive nanofillers, such as graphene nanoplatelets, are characterized by small size, extraordinary surface area to volume ratio, high aspect-ratio and extremely low electrical resistivity. In this work, the dielectric behaviors and the corresponding energy storage capabilities of high aspect-ratio carbon nanofiller/polymer composites were reviewed. At the electrical percolation point, a conductive composite exhibits a sudden and remarkable enhancement in dielectric constant and dielectric loss. The challenge is to maintain the increase in dielectric constant while preventing the increase in dielectric loss. Various physical and chemical methodologies have been followed to overcome this challenge including surface chemistry modifications, physical alignment of nanofillers and utilizing of hybrid mixtures. Promising results were reported to minimize the energy loss due to the conductive network formation. Nanocomposites with a dielectric constant of 10³ and dielectric loss of only 0.08 were successfully fabricated. However, more work is still needed for a further enhancement in dielectric constant and reduction in the energy loss and to improve the storage capabilities of the nanocomposites.

High dielectric permittivity and low loss of polyvinylidene fluoride filled with carbon additives: Expanded graphite versus reduced graphene oxide

Polymer dielectric composites with high dielectric permittivity and low dielectric loss play an increasing important role for modern electronic and electric industry. In this study, polyvinylidene fluoride (PVDF) incorporated with expanded graphite (EG) or reduced graphene oxide (rGO) was prepared by solution casting and the following hot pressing. The structure, morphology, and properties of the obtained products were characterized. In comparison with EG, rGO exhibits well dispersion and strong interaction with PVDF matrix. With the increasing content of conductive fillers, the dielectric permittivity of both PVDF/EG and PVDF/rGO composites shows an increasing trend whereas the dielectric loss keeps at a low level. The dielectric permittivity of PVDF filled with 4 wt% EG and 8 wt% rGO reaches 420 and 38 at 100 Hz, respectively. Moreover, the introduction of EG and rGO improves the mechanical strength and the thermal stability of PVDF matrix.

Ultralight Microcellular Polymer-Graphene Nanoplatelet Foams with Enhanced Dielectric Performance

Dielectric polymer nanocomposites with high dielectric constant (ε') and low dielectric loss (tan δ) are extremely desirable in the electronics industry. Percolative polymer-graphene nanoplatelet (GnP) composites have shown great promise as dielectric materials for high-performance capacitors. Herein, an industrially-viable technique for manufacturing a new class of ultralight polymer composite foams using commercial GnPs with excellent dielectric performance is presented. Using this method, the high-density polyethylene (HDPE)-GnPs composites with a microcellular structure were fabricated by melt-mixing. This was followed by supercritical fluid (SCF) treatment and physical foaming in an extrusion process, which added an extra layer of design flexibility. The SCF treatment effectively in situ exfoliated the GnPs in the polymer matrix. Moreover, the generation of a microcellular structure produced numerous parallel-plate nanocapacitors consisting of GnP pairs as electrodes with insulating polymer as nanodielectrics. This significantly increased the real permittivity and decreased the dielectric loss. The ultralight extruded HDPE-1.08 vol % GnP composite foams, with a 0.15 g·cm^-3 density, had an excellent combination of dielectric properties (ε' = 77.5, tan δ = 0.003 at 1 × 10⁵ Hz), which were superior to their compression-molded counterparts (ε' = 19.9, tan δ = 0.15 and density of = 1.2 g·cm^-3) and to those reported in the literature. This dramatic improvement resulted from in situ GnP's exfoliation and dispersion, as well as a unique GnP parallel-plate arrangement around the cells. Thus, this facile method provides a scalable method to produce ultralight dielectric polymer nanocomposites, with a microscopically tailored microstructure for use in electronic devices.