Effects of chitosan modification, cross-linking, and oxidation on the structure, thermal stability, and adsorption properties of porous maize starch

Cross-linking Arenga pinnata starch and chitosan by citric acid: Structure and properties

In order to improve the processing and digestibility of the Arenga pinnata (Wurmb.) Merr. starch (APS), low concentration citric acid (CA) and chitosan (CS) were used for dual modification. The purpose of this study was to prepare APS and CS complexes with CA, the complexes (CA-CS-APS) physicochemical properties were investigated. The short-range ordered structure (DO), double helix structure (DO) and relative crystallinity (RC) were decreased; CA-CS resulted in the surface roughness of APS, but the particle integrity was preserved; the particle size of CA-CS-APS was increased. Compared with APS, the peak viscosity of CA-CS-APS was decreased from 2534 cP to 27 cP; CA-CS reduced the swelling power of APS, CA3%-CS-APS decreased from 19.00 g/g to 8.17 g/g. The gelatinization enthalpy was decreased after CA-CS modification from 3.25 J/g to 0.55 J/g. CA-CS-APS exhibits higher storage modulus and loss modulus (2067 Pa and 80 Pa). CA-CS significantly improved the anti-digestibility of APS, and the resistant starch (RS) content was increased from 32 % to 39 %. This study provided a simple and effective way to prepare modified starch, which had the potential as food additives or used as a base material for film preparation.

Effect of three polysaccharides with different charge characteristics on the properties of highland barley starch gel

Highland barley, a nutritious whole grain, faces limited market utilization due to the poor heating stability of its starch. The aim of this study was to investigate the effects of three differently charged ionic polysaccharides-guar gum (GG), xanthan gum (XG), and carboxymethyl chitosan (CMC)-on the gel properties of highland barley starch (HBS). GG and XG notably increased pasting viscosity, viscoelasticity, hardness, and strength of HBS gels. Conversely, CMC resulted in decreased gel properties. All three polysaccharides enhanced OH tensile vibration (3000-3800 cm-1), with GG and XG promoting denser honeycomb network structures and lower spin-spin relaxation time (T2), indicating improved structural integrity. In contrast, low concentrations of CMC led to disorder and loose structure. Hydrogen bonding and electrostatic interactions were the main forces by which polysaccharides influenced the properties of starch gels. This research contributes to enhancing the properties of HBS gel during heating and expanding its commercial applications. It also provides some insights to understand the interaction between different charged polysaccharides and starch.

Ultrasound and enzyme treatments on morphology, structures, and adsorption properties of cassava starch

Porous starch materials are environmentally friendly and renewable and exhibit high adsorption performances. Ultrasound and compound enzyme (α-amylase and glucoamylase) treatments were applied to prepare modified cassava starch. The granules, crystal morphology, crystal structure, and molecular structure of starch were investigated. The hydrolysis degree, solubility, swelling, and adsorption properties of cassava starch were analyzed. After the cassava starch was modified by ultrasound and enzyme treatments, the granule size of the starch decreased, and the surfaces were eroded to form pits, grooves and cavity structure. The starch spherulites weakened or even disappeared. The functional groups of starch did not change significantly, but the degree of crystal order decreased. The double-helix structure was reduced, and the crystal structure was composed of A + V-type crystals, with a decrease in crystallinity. The gelatinization temperature and thermal degradation temperatures enhanced. The enzymatic hydrolysis degree and solubility of the modified cassava starch increased. The swelling degree decreased, and oil adsorption, water adsorption improved. MB adsorption behavior of modified cassava starch closely followed a pseudo-second-order kinetics model and the Langmuir isotherm equation. These findings could help to understand the relationship between the structure and properties of modified starch, and guide its application in the field of adsorption.

Effect of Cyperus esculentus polysaccharide on Cyperus esculentus starch: Pasting, rheology and in vitro digestibility

This study investigated the effects of varying amounts of added Cyperus esculentus polysaccharide (CEP) on the physicochemical and structural properties, as well as in vitro digestibility, of homologous Cyperus esculentus starch (CES). Compared to CES, the CES-CEP complexes showed reduced peak viscosity and breakdown value, and improved thermal paste stability of starch. Rheological properties showed that adding CEP reduced the consistency coefficient and pseudoelasticity of the complexes, thus increasing their resistance to shear thinning. FTIR analysis suggested the absence of covalent binding between CES and CEP. SEM showed a more homogeneous and dense gel structure, particularly in the CES-1.0%CEP sample. During in vitro digestion, the content of resistant starch in the complexes increased after CEP was added. Analysis of the interaction forces showed that the CES-CEP complexes had stronger hydrogen bonding and electrostatic interaction. This study offers valuable insights into the potential applications of CEP in starch-based foods.

Chitosan/teff flour active films incorporated with citric acid and beetroot leaf extract: Physicochemical properties and mathematical modeling of phenolic release

Active compounds are integrated into food packaging films to enhance their food protection capabilities. Understanding the release of these components in films, particularly in crosslinking scenarios, is crucial. This study aimed to mathematically model the release of phenolic compounds from chitosan/teff flour films to understand how active compounds gradually release. Moreover, it was aimed to study the effects of incorporation of beetroot leaf extract and citric acid crosslinking. The collective observations, encompassing increased density and thermal stability, alongside concurrent reductions in moisture content, water solubility, water vapor permeability and swelling index following citric acid addition, strongly suggested the presence of crosslinking. Applying Fick's law and the finite element method revealed a substantial influence of the crosslinking agent on diffusion coefficients. The model exhibited strong agreement with experimental data, as reflected in low root mean square error values ranging from 3.02 to 8.50 mmol/m3 for films. Furthermore, the influence of citric acid crosslinking on the release of TPC was evident, as indicated by a decrease in average diffusion coefficient values from 3.499 × 10-13 m2 s-1 to 1.770 × 10-13 m2 s-1 with the formula with 1.5 % citric acid and 0.5 % beetroot leaf extract. This showcases the impact of various parameters on controlled release in food packaging.

Sustained release, antimicrobial, and antioxidant properties of modified porous starch-based biodegradable polylactic acid/polybutylene adipate-co-terephthalate/thermoplastic starch active packaging film

Porous starch (PS) is a modified starch with commendable biodegradable and adsorption properties. PS exhibits poor thermal stability, and the aqueous solution casting method is conventionally used for PS-activated packaging films. This approach limits the large-scale production of films and makes it difficult to play the functions of porous pores. In this study, PS was prepared by enzymatic digestion combined with freeze-drying and adsorbed with clove essential oil (CEO) after cross-linking with sodium trimetaphosphate. Subsequently, a novel PLA/PBAT/TPS/ScPS-CEO sustained release active packaging film was prepared by blending PLA, PBAT, TPS, and ScPS-CEO using industrial melt extrusion. Compared with PS, ScPS effectively slowed down the release of CEO from the film, with the maximum release of active substances at equilibrium increasing by approximately 100 %, which significantly enhanced the persistence of the antimicrobial and antioxidant properties. The polylactic acid/poly (butylene adipate-co-terephthalate)/thermoplastic starch/trimetaphosphate-crosslinked porous starch incorporated with clove essential oil (PLA/PBAT/TPS/ScPS-CEO) film could reduce the proteolysis, lipid oxidation and microbial growth of salmon, extending its shelf life by approximately 100 % at 4 °C. These results indicate that the ScPS can be used in fresh packaging material in practical applications.

Valorization of guinea grass seed (Megathyrsus maximus): Synthesis and utilization of cellulose microfiber to reinforce esterified and cross-linked guinea starch films

The present study extracts starch from guinea grass seed and fiber from the starch extraction residue. The fibrous residue was chemically converted into cellulose microfiber (CMF) and used to reinforce the native, esterified and crosslinked guinea starch films. The films were developed with 5 % starch, 40 % glycerol and 0, 2.5, 5, and 10 % CMF based on the dry matter of starch. SEM images of all film samples showed good compatibility of CMF with starch molecules, and no fractures or pores were observed. Adding filler materials to modified starch films slightly increased the film thickness (0.24 to 0.30 mm) due to the high dimensions of CMF, which comprise a significant amount of the composite's volume. A synergetic effect of starch modification and CMF in films decreased the moisture content (21.98 to 9.21 %), water solubility (25.65 to 15.47 %), water vapor permeability (6.96×10-7 to 1.65×10-7g∙mm2∙day∙Pa), and elongation at the break (33.51 to 16.79 %) while increasing the tensile strength (1.84 to 3.85 MPa) and Young's modulus (5.49 to 22.93 MPa). The L* and a* values of the films decreased, and the b* and opacity values of the films increased with the addition of CMF. The XRD graph showed that all films have semicrystalline structures with peaks at 18°, 20°, and 22°, and the degree of crystallinity increases (32.3 to 55.1 %) with CMF. All film samples showed good thermal stability up to 315 °C. In conclusion, esterified starch-based films exhibited superior barrier properties and flexibility. On the contrary, cross-linked starch films demonstrated higher tensile strength and lower water solubility.

Formation, influencing factors, and applications of internal channels in starch: A review

Starch, a natural polymer, has a complex internal structure. Some starches, such as corn and wheat starches, have well-developed surface pores and internal channels. These channel structures are considered crucial in connecting surface stomata and internal cavities and have adequate space for loading guest molecules. After processing or modification, the starch-containing channel structures can be used for food and drug encapsulation and delivery. This article reviews the formation and determination of starch internal channels, and the influence of different factors (such as starch species and processing conditions) on the channel structure. It also discusses relevant starch preparation methods (physical, chemical, enzymatic, and synergistic), and the encapsulation effect of starch containing internal channels on different substances. In addition, the role of internal channels in regulating the starch digestion rate and other aspects is also discussed here. This review highlights the significant multifunctional applications of starch with a channel structure.

Physicochemical Characteristics of Porous Starch Obtained by Combined Physical and Enzymatic Methods, Part 1: Structure, Adsorption, and Functional Properties

Porous starch can be applied as an adsorbent and encapsulant for bioactive substances in the food and pharmaceutical industries. By using appropriate modification methods (chemical, physical, enzymatic, or mixed), it is possible to create pores on the surface of the starch granules without disturbing their integrity. This paper aimed to analyze the possibility of obtaining a porous structure for native corn, potato, and pea starches using a combination of ultrasound, enzymatic digestion, and freeze-drying methods. The starch suspensions (30%, w/w) were treated with ultrasound (20 kHz, 30 min, 20 °C), then dried and hydrolyzed with amyloglucosidase (1000 U/g starch, 50 °C, 24 h, 2% starch suspension). After enzyme digestion, the granules were freeze-dried for 72 h. The structure of the native and modified starches were examined using VIS spectroscopy, SEM, ATR-FTIR, and LTNA (low-temperature nitrogen adsorption). Based on the electrophoretic mobility measurements of the starch granules using a laser Doppler velocimeter, zeta potentials were calculated to determine the surface charge level. Additionally, the selected properties such as the water and oil holding capacities, least gelling concentration (LGC), and paste clarity were determined. The results showed that the corn starch was the most susceptible to the combined modification methods and was therefore best suited for the production of porous starch.

Preparation, characterization and in vitro digestion of octenyl succinic anhydride-modified porous starch with different degrees of substitution

Octenyl succinic anhydride modified porous starch (OSA-PS) with degrees of substitution (DS) from 0.0123 to 0.0427 were prepared by aqueous phase method. From SEM, PS had a porous structure which showed a rough and corrosive surface after esterification with OSA. FT-IR revealed the characteristic peaks of OSA-PS at 1725 cm-1 and 1570 cm-1. From 1H NMR spectra, OSA-PS displayed extra chemical signal peaks at 0.85 ppm, 1.25 ppm and 1.96 ppm. These results fully demonstrated that OSA groups were successfully grafted onto PS. Furthermore, as DS increased, the specific surface area (5.6464 m2/g), pore volume (0.9959 × 10-2 cm3/g) and methylene blue adsorption capacity (24.3962 mg/g) of OSA-PS reached the maximum, while its relative crystallinity (26.8112 %) and maximum thermal decomposition temperature (291.96 °C) were the minimum. In vitro digestion studies showed that with the increase of DS, OSA-PS' contents of rapidly digestible starch and slowly digestible starch decreased from 9.06 % to 6.27 % and 28.38 % to 14.61 %, respectively. In contrast, its resistant starch had an increase in content from 62.56 % to 79.12%. The results provided an effective method for obtaining a double-modified starch with high specific surface area and anti-digestibility, thus broadening the industrial application of starch.

Preparation of a high-strength, hydrophobic performance starch-based adhesive with oxidative cross-linking via Fenton's reagent

Starch is a highly attractive carbohydrate in the production for the preparation of adhesives in recent years, due to its widespread availability, renewability, and abundance of reactive hydroxyl groups. However, the mechanical properties, hydrophobicity, self-adhesion, and particularly high energy efficiency are generally unsatisfactory for current starch-based adhesives. On this premise, starch was oxidized using Fenton's reagent in a ""one-pot cooking" process. The prepared oxidized starch was chain expanded by polyvinyl alcohol (PVA) and then cross-linked with a 10 % isocyanate (PM-200) to fabricate a starch-based adhesive (SFA) with a network crosslinked structure. SF12A35%/2.5-55 adhesive shows significantly higher wet shear strength (1.18 MPa), a remarkable 94 % increase compared to SF0A35%/2.5-55. The adhesive film also demonstrates both hydrophobicity (99° contact angle) and exceptional energy efficiency, with a DSC test revealing a notable 10 % elevation in energy efficiency. In addition, the crosslinked structure increases its molecular weight, thereby increasing its self-adhesion (Fig. S1). This study opens up new possibilities for the design and manufacture of multifunctional starch-based adhesives.

Adsorption properties of corn starch modified by malt amylases and crosslinking agents: A comparison between sodium trimetaphosphate and organic acids

In order to investigate the effects of different crosslinking agents on physicochemical properties and adsorption properties of porous starch. Native corn starch was hydrolyzed by maltase and crosslinked with different crosslinking agents. Sodium trimetaphosphate crosslinked porous starch (STMP-MPS), malic acid cross-linked porous starch (MA-MPS) and citric acid cross-linked porous starch (CA-MPS) were prepared. After crosslinking, MA-MPS and CA-MPS showed a new CO stretching absorption peak at 1738 cm-1, and the crosslinking degree was much higher than that of STMP-MPS. The surface area of MA-MPS was 36 % higher than that of STMP-MPS. Compared with the average pore size of 12.43 nm of STMP-MPS, CA-MPS (14.02 nm) and MA-MPS (14.79 nm) were increased more significantly. The degradation temperature of MA-MPS and CA-MPS was increased by the introduction of ester bond, which indicates that the organic acid cross-linking strengthens the starch granules and hence more energy is required for disruption. Compared with STMP-MPS, the water absorption of MA-MPS and CA-MPS increased by 64 % and 32 %, respectively. Furthermore, the adsorption capacity of MA-MPS to essential oil was the strongest, about 4 times that of STMP-MPS. Overall, it is feasible to modify porous starch by crosslinking reaction to improve its heat resistance and adsorption properties.

A review of starch swelling behavior: Its mechanism, determination methods, influencing factors, and influence on food quality

Swelling behavior involves the process of starch granules absorbing enough water to swell and increase the viscosity of starch suspension under hydrothermal conditions, making it one of the important aspects in starch research. The changes that starch granules undergo during the swelling process are important factors in predicting their functional properties in food processing. However, the factors that affect starch swelling and how swelling, in turn, affects the texture and digestion characteristics of starch-based foods have not been systematically summarized. Compared to its long chains, the short chains of amylose easily interact with amylopectin chains to inhibit starch swelling. Generally, reducing the swelling of starch could increase the strength of the gel while limiting the accessibility of digestive enzymes to starch chains, resulting in a reduction in starch digestibility. This article aims to conduct a comprehensive review of the mechanism of starch swelling, its influencing factors, and the relationship between swelling and the pasting, gelling, and digestion characteristics of starch. The role of starch swelling in the edible quality and nutritional characteristics of starch-based foods is also discussed, and future research directions for starch swelling are proposed.

Starch chain-length distributions determine cooked foxtail millet texture and starch physicochemical properties

Starch chain-length distributions play an important role in controlling cereal product texture and starch physicochemical properties. Cooked foxtail millet texture and starch physicochemical properties were investigated and correlated with starch chain-length distributions in eight foxtail millet varieties. The average chain lengths of amylopectin and amylose were in the range of DP 24-25 and DP 878-1128, respectively. The percentage of short amylopectin chains (Ap1) was negatively correlated with hardness but positively correlated with adhesiveness and cohesion. Conversely, the amount of amylose intermediate chains was positively correlated with hardness but negatively correlated with adhesiveness and cohesion. Additionally, the amount of amylose long chains was negatively correlated with adhesiveness and chewiness. The relative crystallinity (RC) of starch decreased with reductions in the length of amylopectin short chains in foxtail millet. Pasting properties were mainly influenced by the relative length of amylopectin side chains and the percentage of long amylopectin branches (Ap2). Longer amylopectin long chains resulted in lower gelatinization temperature and enthalpy (ΔH). The amount of starch branched chains had important effects on the gelatinization temperature range (ΔT). These results can provide guidance for breeders and food scientists in the selection of foxtail millet with improved quality properties.

Cytotoxicity Enhancement of α-Mangostin with Folate-Conjugated Chitosan Nanoparticles in MCF-7 Breast Cancer Cells

α-mangostin (AM) is a promising natural anticancer agent that can be used in cancer research. However, its effectiveness can be limited by poor solubility and bioavailability. To address this issue, chitosan-based nanoparticles (CSNPs) have been investigated as a potential delivery system to enhance the cytotoxicity to cancer cells and improve selectivity against normal cells. In this study, we developed folate-conjugated chitosan nanoparticles (F-CS-NPs) using a carbodiimide-based conjugation method to attach folate to chitosan (CS), which have different molecular weights. The NPs were crosslinked using tripolyphosphate (TPP) via ionic gelation. To characterize the F-CS-NPs, we utilized various analytical techniques, including transmission electron microscopy (TEM) to evaluate the particle size and morphology, Fourier-transform infrared spectroscopy (FTIR) to confirm the presence of functional groups, and ultraviolet-visible spectroscopy (UV-Vis) to measure the absorption spectrum and confirm the presence of folate. The particle size of AM-F-CS-NPs ranged from 180 nm to 250 nm, with many having favorable charges ranging from +40.33 ± 3.4 to 10.69 ± 1.3 mV. All NPs exhibited the same spherical morphology. The use of F-CS-NPs increased drug release, followed by a sustained release pattern. We evaluated the cytotoxicity of AM, AM-F-CS-HMW, and AM-F-CS-LMW NPs against MCF-7 cells and found IC50 values of 8.47 ± 0.49, 5.3 ± 0.01, and 4.70 ± 0.11 µg/mL, respectively. These results confirm the improved cytotoxicity of AM in MCF-7 cells when delivered via F-CS-NPs. Overall, our in vitro study demonstrated that the properties of F-CS-NPs greatly influence the cytotoxicity of AM in MCF-7 breast cancer cells (significantly different (p < 0.05)). The use of F-CS-NPs as a drug-delivery system for AM may have the potential to develop novel therapies for breast cancer.

Modified porous starch for enhanced properties: Synthesis, characterization and applications

Native starches have low water solubility at room temperature and poor stability, which demand modifications to overcome. Porous starch as a modified one shows enhanced adsorptive efficiency and solubility compared with its native starch. In contrast, some inherent disadvantages exist, such as weak mechanical strength and low thermal resistance. Fortunately, modified porous starches have been developed to perform well in adsorption capacity and stability. Modified porous starch can be prepared by esterification, crosslinking, oxidation and multiple modifications to the porous starch. The characterization of modified porous starch can be achieved through various analytical techniques. Modified porous starch can be utilized as highly efficient adsorbents and encapsulants for various compounds and applied in various fields. This review dealt with the progress in the preparation, structural characterization and application of modified porous starch. The objective is to provide a reference for its development, utilization, and future research directions.

Modified porous starches loading curcumin and improving the free radical scavenging ability and release properties of curcumin

Maize porous starch-curcumin microspheres were prepared by encapsulating curcumin into cross-linked porous starch and oxidized porous starch to investigate the effect of modified porous starch in embedding and protecting curcumin. The morphology and physicochemical properties of microspheres were analyzed using scanning electron microscopy, Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction, Zeta/DLS, Thermal stability, and antioxidant activity; the release of curcumin was evaluated with a simulated gastric-intestine model. The FT-IR results revealed that curcumin was amorphously encapsulated in the composite and hydrogen bond formation between starch and curcumin was one of the major driving forces for encapsulation. Microspheres increased the initial decomposition temperature of curcumin, which has a protective effect on curcumin. Modification improved the encapsulation efficiency and the scavenging free radical ability of porous starch. The release mechanism of curcumin from microspheres fits first-order and Higuchi models well in gastric and intestinal models, respectively, indicating that encapsulation of curcumin within different porous starches microspheres enables controlled release of curcumin. To recapitulate, two different modified porous starch microspheres improved the drug loading, slow release and free radical scavenging effects of curcumin. Among them, the cross-linked porous starch microspheres had higher encapsulation and slow release ability for curcumin than the oxidized porous starch microspheres. It provides theoretical significance and data basis for the encapsulation of active substances by modified porous starch.

Preparation and characterization of functionalized chitosan/polyvinyl alcohol composite films incorporated with cinnamon essential oil as an active packaging material

In this study, amphiphilic chitosan (NPCS-CA) was synthesized by grafting quaternary phosphonium salt and cholic acid onto the chain of chitosan, aiming to develop an active edible film based on NPCS-CA and polyvinyl alcohol (PVA) incorporated with cinnamon essential oil (CEO) by the casting method. The chemical structure of the chitosan derivative was characterized by FT-IR, ¹H NMR and XRD. Through the characterization of FT-IR, TGA, mechanical and barrier properties of the composite films, the optimal proportion of NPCS-CA/PVA was determined as 5/5. And, the tensile strength and elongation at break of the NPCS-CA/PVA (5/5) film with 0.4 % CEO were 20.32 MPa and 65.73 %, respectively. The results revealed that the NPCS-CA/PVA-CEO composite films exhibited an excellent ultraviolet barrier property at 200-300 nm and significantly reduced oxygen permeability, carbon dioxide permeability and water vapor permeability. Furthermore, the antibacterial property of film-forming solutions against E. coli, S. aureus, and C. lagenarium was distinctly improved with the increase of NPCS-CA/PVA proportion. And, the multifunctional films effectively extended the shelf-life of mangoes at 25 °C based on the characterization of surface changes and quality indexes. The NPCS-CA/PVA-CEO films could be developed as biocomposite food packaging material.

Amylose content and pre-freezing regulate the structure and oil absorption of polyelectrolytes-based starch cryogel

Starch cryogel is a potential material for oil absorption. This study provided a facile and convenient polyelectrolyte-based preparation strategy of starch cryogel, in which the structural properties of the cryogel were regulated by amylose content and pre-freezing without long-time retrogradation. Sodium laurate was used as a guest model to form starch-fatty acid salt complex (polyelectrolyte). The amount of amylose content and sodium laurate added led more polyelectrolytes, significantly increased V-type crystallinity from 3.72 % to 22.40 % and complexing index from 4.32 % to 28.48 %. As the uniform pore structure improved the oil absorption ability of starch cryogel, the starch cryogel prepared by waxy maize starch followed by quick pre-freezing showed the highest specific surface area (9.87 m²/g) and oil absorption capacity (32.94 g/g). Our findings suggest that polyelectrolyte properties have great potential in the preparation of starch-based cryogels, which could be applied in the design of novel starch-based porous materials.

A novel lotus seed cross-linked resistant starch: Structural, physicochemical and digestive properties

The structural properties and physicochemical characteristics of lotus seed cross-linked resistant starches (LSCSs; LS-0CS, LS-1CS, LS-2CS, LS-4CS, LS-6CS, LS-8CS, LS-10CS, and LS-12CS) with different concentrations of cross-linking agents were investigated. The degrees of cross-linking of LSCSs increased along with the amount of cross-linking agent. The higher the degree of cross-linking, the greater the degree of LSCSs granule agglomeration. The occurrence of the cross-linking reaction was confirmed by the appearance of P = O at 1,250 cm^–1 as assessed by FT-IR, and the covalent bonds formed by the phosphate group in LSCSs were mainly composed of distarch monophosphate (DMSP) as determined by ³¹P NMR. As the crosslinking degree increased, the peak strength of DMSP in starch was stronger and the specific gravity of DMSP was larger. Among the samples, LS-12CS had the highest cross-linking degree, with a greater specific gravity of DMSP. Moreover, the solubility levels of LSCSs decreased and the thermal stability and anti-digestive properties improved as the cross-linking degree increased, which was correlated with the degree of agglomeration and DMSP in LSCSs. The RS content of LS-12CS was 48.95 ± 0.86%.

Preparation and characterization of chitosan derivatives modified with quaternary ammonium salt and quaternary phosphate salt and its effect on tropical fruit preservation

In this paper, HACC modified with (5-Carboxypentyl) (triphenyl) phosphonium bromide (HA-CS-NP) was synthesized. Then, a multifunctional food packaging composite film with good thermal stability and antibacterial functions was fabricated by HA-CS-NP and poly (vinyl alcohol) (PVA). The tensile strength and elongation at break of HA-CS-NP/PVA composite film at the weight ratio of 3/7 were 20.32 ± 1.02 MPa and 65.73 ± 3.29%, respectively. And, the inhibition rates of HA-CS-NP (0.5%) on Mango C. lagenarium and Papaya C. gloeosporioides on day 6 were up to 80.92 ± 4.12%. Compared with CK group, the weight loss of experimental groups were 23.96 ± 2.46 g/206 ± 7.25 g (mangoes) and 59.45 ± 3.06 g/496 ± 6.37 g (papaya), reduced by 35.76 ± 1.15%. Moreover, the final hardness value of the fruits coated with composite films was 4.94 ± 0.23 kg/cm³ and increased by 20.79 ± 1.04%, and the rot index was reduced by 71.43 ± 3.24%. The multifunctional HA-CS-NP/PVA coating has broad prospects in the application of food packaging.

Temperature of plasma-activated water and its effect on the thermal and chemical surface properties of cereal and tuber starches

High amylose and waxy starches from maize and potato were incubated with plasma-activated water (PAW) at 25 °C, 60 °C, and 80 °C temperatures to investigate PAW treatment effects on the starches' properties. At 60 °C incubation temperature, the starches were basically annealed with PAW. Annealing starches with PAW significantly increased (p < 0.05) the gelatinization parameters except for the enthalpy of gelatinization of waxy potato starch. Furthermore, starch swelling power significantly decreased while the water absorption capacity and solubility increased significantly when incubated at 80 °C. X-ray photoelectron spectroscopy (XPS) analysis showed the oxidation of C–C/C–H and C–O into carboxyl groups in waxy and high amylose maize starches incubated with PAW at 60 °C and 80 °C, respectively. In addition, cross-linking was observed in waxy maize and high amylose potato incubated with PAW at 80 °C and 25 °C, respectively. Overall, the results indicated PAW temperature is an important factor in modifying cereals and tuber starches with PAW.

•

Maize and potato starches were treated with plasma-activated water (PAW).

•

Increasing the temperature of PAW improves the hydration properties of starch.

•

Gelatinization temperatures increased with an increase in the temperature of PAW.