A decade development in the application of chitosan-based materials for dye adsorption: A short review

All-weather-available down carbon fiber hydrogel with enhanced mechanical properties for simultaneous efficient clean water generation and dye adsorption from dye wastewater

Solar-driven photothermal conversion can produce clean water from dye wastewater while leaving the dye in the evaporation medium. Herein, a biomass-based composite hydrogel via down-fiber carbon (DFC) aerogel modified with chitosan-polyvinyl alcohol (CS-PVA) hydrogel was designed to address the aforementioned problem. The CS-PVA@DFC hydrogel integrated the capacity of simultaneous clean water production/dye adsorption during the day and continuous dye adsorption during the night. Furthermore, the modification of the CS-PVA hydrogel endowed the composite hydrogel with enhanced compression stress of 190.07 kPa (76.03 times that of DFC aerogel of 2.50 kPa) and impressive resilient recovery. Moreover, the CS-PVA@DFC hydrogel possessed solar light absorption of 99.56 % and strengthened water replenishment capacity due to the high porosity and CS-PVA hydrophilic network structure. The CS-PVA@DFC hydrogel demonstrated a stable, high evaporation rate of 2.34 kg·m-2·h-1 and simultaneous dye adsorption capacity of 70.39 % for treating methyl orange dye solution within 5 h. Additionally, the 24-h outdoor test showed that the CS-PVA@DFC hydrogel possessed excellent clean water production capacity during the daytime (reaching 4.17 kg·m-2·h-1 at 1:00p.m.) and continuous satisfactory dye adsorption capacity all day (89.68 %). These findings will inspire researchers seeking opportunities to improve the mechanical properties of aerogel and its application for treating wastewater, especially wastewater with harmful dyes.

Accessible Eco-Friendly Method for Wastewater Removal of the Azo Dye Reactive Black 5 by Reusable Protonated Chitosan-Deep Eutectic Solvent Beads

A novel approach to enhance the utilization of low-cost and sustainable chitosan for wastewater remediation is presented in this investigation. The study centers around the modification of chitosan beads using a deep eutectic solvent composed of choline chloride and urea at a molar ratio of 1:2, followed by treatment with sulfuric acid using an impregnation accessible methodology. The effectiveness of the modified chitosan beads as an adsorbent was evaluated by studying the removal of the azo dye Reactive Black 5 (RB5) from aqueous solutions. Remarkably, the modified chitosan beads demonstrated a substantial increase in adsorption efficiency, achieving excellent removal of RB5 within the concentration range of 25-250 mg/L, ultimately leading to complete elimination. Several key parameters influencing the adsorption process were investigated, including initial RB5 concentration, adsorbent dosage, contact time, temperature, and pH. Quantitative analysis revealed that the pseudo-second-order kinetic model provided the best fit for the experimental data at lower dye concentrations, while the intraparticle diffusion model showed superior performance at higher RB5 concentration ranges (150-250 mg/L). The experimental data were successfully explained by the Langmuir isotherm model, and the maximum adsorption capacities were found to be 116.78 mg/g at 298 K and 379.90 mg/g at 318 K. Desorption studies demonstrated that approximately 41.7% of the dye could be successfully desorbed in a single cycle. Moreover, the regenerated adsorbent exhibited highly efficient RB5 removal (80.0-87.6%) for at least five consecutive uses. The outstanding adsorption properties of the modified chitosan beads can be attributed to the increased porosity, surface area, and swelling behavior resulting from the acidic treatment in combination with the DES modification. These findings establish the modified chitosan beads as a stable, versatile, and reusable eco-friendly adsorbent with high potential for industrial implementation.

Preparation of magnetic DTPA-modified chitosan composite microspheres for enhanced adsorption of Pb(II) from aqueous solution

In this study, magnetic DTPA-modified chitosan composite microspheres (MDCM) were prepared by reverse emulsion-double crosslinking method (carbodiimide followed by glutaraldehyde) for removal of Pb(II) from aqueous solution. The obtained magnetic adsorbents were characterized by FTIR, SEM, XRD, VSM, BET, and 13C NMR. The effects of the pH, contact time, initial concentration, and competitive metal cations (Na(I), Ca(II), or Mg(II)) on Pb(II) adsorption were investigated. The results revealed that MDCM exhibited high removal performance over a wide pH range and in the presence of competitive metal cations. The maximum adsorption capacity of MDCM for Pb(II) is 214.63 mg g-1 at pH 3, which is higher than most recently reported magnetic adsorbents. Adsorption kinetics and isotherms can be described by the pseudo-second-order model and Langmuir model, respectively. In addition, MDCM is easy to regenerate and can be reused five cycles with high adsorption capacity. Finally, the adsorption mechanism was further revealed by FTIR and XPS analysis. Overall, MDCM has practical application potential in removing Pb(II) from contaminated wastewater due to its high adsorption efficiency, good reusability, and convenient magnetic separation.

Chitosan/functionalized fruit stones as a highly efficient adsorbent biomaterial for adsorption of brilliant green dye: Comprehensive characterization and statistical optimization

In this research, a highly efficient adsorbent biomaterial (hereinafter, CTS/PPS-HS) of chitosan/functionalized fruit stones (peach and plum) with H2SO4 was produced for the adsorption of brilliant green (BG) dye from aquatic systems. The developed biomaterial was characterized by several techniques like SEM-EDX, FTIR, XRD, BET, and pHpzc. To systematically optimize the adsorption performance of CTS/PPS-HS, the Box-Behnken design (BBD) based on response surface methodology (RSM) was attained. The factors considered for optimization included A: CTS/PPS-HS dosage (0.02-0.08 g), B: pH (4-10), and C: removal time (10-60 min). The pseudo-first-order and Langmuir isotherm models exhibited excellent agreement with the experimental results of BG adsorption by CTS/PPS-HS. The outstanding adsorption capacity (409.63 mg/g) of CTS/PPS-HS was obtained. The remarkable adsorption of BG onto CTS/PPS-HS can be primarily attributed to electrostatic forces between the acidic sites of CTS/PPS-HS and the BG cations, accompanied by interactions such as π-π, Yoshida H-bonding, n-π, and H-bond interactions. The current data underscores the significant potential inherent in combining biomass with CTS polymer to create an exceptionally effective adsorbent biomaterial tailored for the elimination of cationic dyes.

Preparation of novel and recyclable chitosan-alumina nanocomposite as superabsorbent to remove diazinon and tetracycline contaminants from aqueous solution

This work presents a novel, strong and efficient adsorbent (CS@TDI@EDTA@γ-AlO(OH)) prepared through the green process using three components, chitosan, BNPs and EDTA using amide and ester bridges. An eco-friendly and easy approach was used for the preparation of this novel adsorbent, the low cost, easy access to the used materials, and the simplicity of the preparation method are some of the interesting advantages of this work. Also, this prepared adsorbent was used as an adsorbent to remove diazinon organophosphate poison and tetracycline antibiotic from aqueous solutions. In order to confirm the prepared adsorbent structure, the CS@TDI@EDTA@γ-AlO(OH) composite was investigated by various analyses including FT-IR, EDX, XRD, FESEM and TGA. The adsorption behavior of the adsorbent prepared for the removal of tetracycline and diazinon was investigated under different conditions by varying the concentration, temperature, the adsorbent dose, pH and contact time. Based on various tests, the highest diazinon adsorption capacity was obtained for 0.12 g/L adsorbent at pH 7 and 60 °C with 40 mg/L initial concentration. Also, the maximum adsorption capacity of the tetracycline was obtained for 0.12 g/L adsorbent at pH 9 and 60 °C with 30 mg/L initial concentration. The equilibrium results for diazinon and for tetracycline were in good accordance with the Langmuir and Freundlich isotherm models, respectively. Also, the highest adsorption capacities for diazinon at pH 7 and tetracycline at pH 9 were 1428.5 and 555.5 mg/g, respectively. Also the kinetic investigations revealed that the correlation factor (R2) of pseudo-second-order model obtained for the adsorption of diazinon and tetracycline was 0.9986 and 0.9988, while the coefficient k (g/mg.min) was 0.000084 and 0.0033, respectively. These results indicate that the adsorption of diazinon and tetracycline is pseudo-second-order kinetics model. Formation of hydrogen bonds between adsorbate and adsorbent as well as the high specific surface area and porosity of the adsorbent are the main mechanisms that contribute to the adsorption process. In addition, thermodynamic studies indicated that the adsorption of diazinon and tetracycline is a spontaneous endothermic process. The adsorbent prepared in this work was expected to have wide range of applications in wastewater treatment thanks to its good reusability in water and strong removal of diazinon and tetracycline compared to other adsorbents.

Chitosan derivatives as dynamic coatings for transferrin glycoform separation in capillary electrophoresis

Chitosan and its derivatives are interesting biopolymers for different field of analytical chemistry, especially in separation techniques. The present study was aimed at testing chitosan water soluble derivatives as dynamic coating agents for application to capillary electrophoresis. In particular, chitosan was modified following three different chemical reactions (nucleophilic substitution, reductive amination, and condensation) to introduce differences in charge and steric hindrance, and to assess the effect of these physico-chemical properties in capillary electrophoresis. The effects were tested on the capillary electrophoretic separation of the glycoforms of human transferrin, an important iron-transporting serum protein, one of which, namely disialo-transferrin (CDT), is a biomarker of alcohol abuse. Chitosan derivatives were characterized by using NMR and 1H NMR, HP-SEC-TDA, DLS, and rheology. The use of these compounds as dynamic coatings in the electrolyte running buffer in capillary electrophoresis was tested assessing the peak resolution of the main glycoforms of human transferrin and particularly of disialo-transferrin. The results showed distinct changes of the peak resolution produced by the different derivatives. The best results in terms of peak resolution were achieved using polyethylene glycol (PEG)-modified chitosan, which, in comparison to a reference analytical approach, provided an almost baseline resolution of disialo-transferrin from the adjacent peaks.

Study on the deacetylation and mechanism of chitin in natural deep eutectic solvent

A large number of hydrogen bonds is the main reason for hindering the dissolution and reaction of chitin, and a mild and green deacetylation method to prepare chitosan for a wider range of applications is urgent. As a non-toxic and degradable green solvent, the deep eutectic solvent can effectively interfere with the hydrogen bond network of chitin, making chitin more susceptible to other solvents. Therefore, a NADES system consisting of betaine and glycerol was proposed for application in the deacetylation reaction of chitin to facilitate further attack of N-acetyl groups by low concentrations of NaOH. After optimizing the reaction conditions, chitosan with 83.77 % deacetylation was prepared, requiring only a concentration of 25 wt% NaOH. The analysis of the product chitosan showed that NADES could not only effectively improve the degree of deacetylation, but also reduce the degree of damage to the molecular weight by alkali. In addition, the potential mechanisms involved in the deacetylation process by NADES were explored. The nature of the reaction was verified by FT-IR, XRD and theoretical calculations as the process of opening intra/intermolecular hydrogen bonds of chitin by NADES. More importantly, experimental and in-depth theoretical studies provide a reference for the green preparation of chitosan.

Coagulative removal of microplastics from aqueous matrices: Recent progresses and future perspectives

Coagulation-flocculation-sedimentation (CFS) system has been identified as one of the favored treatment technique in water/wastewater treatment systems and hence, it is crucial to comprehend the efficacy of different coagulants used in removing microplastics (MPs) from aqueous matrices. Henceforth, this study critically reviews the recent progress and efficacy of different coagulants used to date for MPs removal. This includes laboratory and field-scale studies on inorganic and organic coagulants, as well as laboratory-scale studies on natural coagulants. Inorganic and organic coagulants have varying MPs removal efficiencies such as: Fe/Al-salts (30 %-95 %), alum (99 %), and poly aluminum chloride (13 %-97 %), magnesium hydroxide (84 %), polyamine (99 %), organosilanes (>95 %), and polyacrylamide (85 %-98 %). Moreover, studies have highlighted the use of natural coagulants, such as chitosan, protein amyloid fibrils, and starch has shown promising results in MPs removal with sevral advantages over traditional coagulants. These natural coagulants have demonstrated high MPs removal efficiencies with chitosan-tannic acid (95 %), protein amyloid fibrils (98 %), and starch (>90 %). Moreover, the MPs removal efficiencies of natural coagulants are compared and their predominant removal mechanisms are determined. Plant-based natural coagulants can potentially remove MPs through mechanisms such as polymer bridging and charge neutralization. Further, a systematic analysis on the effect of operational parameters highlights that the pH affects particle surface charge and coagulation efficiency, while mixing speed affects particle aggregation and sedimentation. Also, the optimal mixing speed for effective MPs removal depends on coagulant type and concentration, water composition, and MPs characteristics. Moreover, this work highlights the advantages and limitations of using different coagulants for MPs removal and discusses the challenges and future prospects in scaling up these laboratory studies for real-time applications.

Process optimization of adsorptive phytoremediation of mutagenic brilliant green dye for health risk management using chemically activated Symplocos racemosa agro-waste

Textile industries use large amounts of water as well as dyes. These dyes containing water are then discharged into the water bodies causing a significant role in water pollution. Brilliant Green dye contributes to many harmful diseases related to the respiratory and gastrointestinal tract. In this study, Symplocos racemosa (SR) agro-waste was chemically treated with acid (SR-HCl) and base (SR-NaOH) and then used for removing Brilliant Green Dye (BGD) on the batch scale. They were characterized by SEM, EDX, FTIR, XRD, TGA and DSC. Optimized conditions were 30 °C temperature, pH 6, adsorbent dose of 0.10 g/25 ml dye solution, shaking speed of 100 revolutions per minute, initial dye concentration of 50 ppm and 35 min time for shaking adsorbent and dye solution. Adsorption data obtained were analyzed using isotherms. The experimental data was found to fit well with the Langmuir model and the maximum adsorption capacity (qmax) of BGD on the SR, SR-HCl, and SR-NaOH was revealed to be 62.90, 65.40, and 71 mg/g respectively. Kinetic data (pseudo-first-order and pseudo-second-order) were evaluated and adsorption tends to follow the pseudo-2nd-order, which indicated the chemisorption mechanism. The results revealed that Symplocos racemosa agro-waste can be considered as the potential biosorbent.

Chitosan/carboxymethylcellulose polyelectrolyte complexes (PECs) are an effective material for dye and heavy metal adsorption from water

Granular macroscopic chitosan/carboxymethylcellulose polyelectrolytic complexes (CHS/CMC macro-PECs) were produced and tested as adsorbents for six pollutants often present in wastewaters: sunset yellow (YS), methylene blue (MB), Congo red (CR) and safranin (S), cadmium (Cd²⁺) and lead (Pb²⁺). The optimum adsorption pH values at 25 °C were 3.0, 11.0, 2.0, 9.0, 10.0, and 9.0 for YS, MB, CR, S, Cd²⁺, and Pb²⁺, respectively. Kinetic studies indicated that the pseudos-econd order model best represented the adsorption kinetics of YS, MB, CR, and Cd²⁺, whereas the pseudo-first order model was the most suitable for S and Pb²⁺ adsorption. The Langmuir, Freundlich, and Redlich-Peterson isotherms were fitted to experimental adsorption data, with the Langmuir model providing the best fit. The maximum adsorption capacity (q_máx) of CHS/CMC macro-PECs for the removal of YS, MB, CR, S, Cd²⁺, and Pb²⁺ was 37.81, 36.44, 70.86, 72.50, 75.43, and 74.42 mg/g, respectively (corresponding to 98.91 %, 94.71 %, 85.73 %, 94.66 %, 98.46 %, and 97.14 %). Desorption assays showed that CHS/CMC macro-PECs can be regenerated after adsorbing any of the six pollutants studied, with possibility of reuse. These results provide an accurate quantitative characterization of the adsorption of organic and inorganic pollutants on CHS/CMC macro-PECs, indicating a novel technological applicability of these two inexpensive, easy-to-obtain polysaccharides for water decontamination.

Facile fabrication of chitosan Schiff bases from giant tiger prawn shells (Penaeus monodon) via solvent-free mechanochemical grafting

Fabrication of chitosan Schiff bases (ChSB) from giant tiger prawn shells (Penaeus monodon) using an environmentally friendly method has been conducted successfully. Transformation of Prawn Shells (PS) as raw material into chitin then chitosan was executed under ambient temperature. Later, three Ch Schiff bases (ChSB-A, ChSB-S, and ChSB-V) were successfully synthesized for the first time via solvent-free mechanochemical grafting with 2-hydroxy benzaldehyde, 4-methoxy benzaldehyde, and 3-methoxy-4-hydroxy benzaldehyde, respectively. Synthesis was carried out with Shaker Mill-Ultimate Gravity equipped with a Teflon jar with zirconia balls; then the product was characterized. FTIR analysis proved the conversion of free amine to imine groups. The degree of substitution (DS) and crystallinity index (CrI) were determined by elemental analysis and X-ray diffraction. The DS values obtained were about 0.343, 0.795, and 0.055 for ChSB-A, ChSB-S, and ChSB-V, respectively. The CrI of ChSB-A, ChSB-S, and ChSB-V was 53.3, 51.7, and 46.9 %, respectively. The thermal gravimetric analysis showed that the mechanochemical grafting of Ch improves the thermal stability of ChSB. This developed method provides a novel potential technique to convert PS into ChSB products by solvent-free mechanochemical grafting.

Enhanced Adsorption Performance Cross-Linked Chitosan/Citrus reticulata Peel Waste Composites as Low-Cost and Green Bio-Adsorbents: Kinetic, Equilibrium Isotherm, and Thermodynamic Studies

This study revealed the synthesis of cross-linked chitosan/Citrus reticulata peel waste (C/CRPW) composites that could be used as low-cost and green bio-adsorbents for the removal of Congo red (CR) dye from aqueous solutions. C/CRPW composites containing different amounts of Citrus reticulata peel waste (CRPW) and chitosan were prepared and cross-linked with glutaraldehyde. The composites were characterized by FESEM, EDS, FTIR, XRD, BET, and zeta potential measurements. The C/CRPW composites as a new type of bio-adsorbents displayed superior adsorption capability toward anionic CR molecules, and the adsorption capacities increased with the incorporation of CRPW. Effects of different ambient conditions, such as contact time, pH, adsorbent dosage, initial adsorbate concentration, and temperature, were fully studied. The conditions which obtained 43.57 mg/g of the highest adsorption capacity were conducted at pH 4 with an initial concentration of 100 mg/L, adsorbent dosage of 2.0 g/L, and contact time of 24 h at 328 K. The adsorption data was found to follow the pseudo-second-order kinetic model and the Freundlich isotherm model. According to the findings of this investigation, it was observed that the C/CRWP composites could be used as adsorbents due to their advantages, including the simple preparation process, being environmentally friendly, renewable, efficient, and low-cost.

Chitosan-Silica Composites for Adsorption Application in the Treatment of Water and Wastewater from Anionic Dyes

A series of new types of composites (biopolymer-silica materials) are proposed as selective and effective adsorbents. A new procedure for the synthesis of chitosan-nanosilica composites (ChNS) and chitosan-silica gel composites (ChSG) using geometrical modification of silica and mechanosorption of chitosan is applied. The highest adsorption efficiency was achieved at pH = 2, hence the desirability of modifications aimed at stabilizing chitosan in such conditions. The amount of chitosan in the synthesis grew to 1.8 times the adsorption capacity for the nanosilica-supported materials and 1.6 times for the silica gel-based composites. The adsorption kinetics of anionic dyes (acid red AR88) was faster for ChNS than for ChSG, which results from a silica-type effect. The various structural, textural, and physicochemical aspects of the chitosan-silica adsorbents were analyzed via small-angle X-ray scattering, scanning electron microscopy, low-temperature gas (nitrogen) adsorption, and potentiometric titration, as well as their adsorption effectiveness towards selected dyes. This indicates the synergistic effect of the presence of dye-binding groups of the chitosan component, and the developed interfacial surface of the silica component in composites.

The use of chitosan-based composites for environmental remediation: A review

The presence of hazardous pollutants in water sources as a result of industrial activities is a major environmental challenge that impedes the availability of safe drinking water. Adsorptive and photocatalytic degradative removal of various pollutants in wastewater have been recognized as cost-effective and energy-efficient strategies. In addition to its biological activity, chitosan and its derivatives are considered as promising materials for the removal of various pollutants. The abundance of hydroxyl and amino groups in the chitosan macromolecular structure results in a variety of concurrent pollutant's adsorption mechanisms. Furthermore, adding chitosan to photocatalysts increases the mass transfer while decreasing both the band gap energy and the amount of intermediates produced during photocatalytic processes, improving the overall photocatalytic efficiency. Herein, we have reviewed the current design and preparation of chitosan and its composites, as well as their applications for the removal of various pollutants by adsorption and photocatalysis processes. Effects of operating variables such as the pH, catalyst mass, contact time, light wavelength, initial pollutant's concentration, and catalyst recyclability, are discussed. Various kinetic and isotherm models are presented to elucidate the rates, and mechanisms of pollutant's removal, onto chitosan-based composites, and several case studies are presented. Additionally, the antibacterial activity of chitosan-based composites has been discussed. This review aims to provide a comprehensive and up-to-date overview of the applications of chitosan-based composites in wastewater treatment and put forward new insights for the development of highly effective chitosan-based adsorbents and photocatalysts. Finally, the main challenges and future directions in the field are discussed.

Enhanced dye adsorption with conductive polyaniline doped chitosan nanofibrous membranes

Polyaniline is widely used in the field of electrochemistry due to its excellent electrical conductivity. However, its effectiveness and mechanism of enhancing adsorption property are unclear. Herein, chitosan/polyaniline nanofibrous composite membranes with average diameter ranging from 200 to 300 nm were fabricated by electrospinning technology. The as-prepared nanofibrous membranes exhibited significantly improved adsorption capacity of 814.9 mg/g and 618.0 mg/g towards acid blue 113 and reactive orange dyes, which were 121.8 % and 99.4 % higher than that of pure chitosan membrane. The doped polyaniline promoted the dye transfer rate and capacity due to the enhanced conductivity of the composite membrane. Kinetic data showed that chemisorption was the rate-limiting step, and thermodynamic data indicated the adsorption of the two anionic dyes was spontaneous monolayer adsorption. This study provides a feasible strategy to introduce conductive polymer into adsorbent to construct high performance adsorbents for wastewater treatment.

Methylene blue removal from aqueous solutions using a biochar/gellan gum hydrogel composite: Effect of agitation mode on sorption kinetics

Hydrogel membranes are prepared by casting a mixture of gellan gum (associated with PVA) and biochar produced from a local Egyptian plant. The mesoporous material is characterized by a specific surface area close to 134 m² g^-1, a residue of 28 % (at 800 °C), and a pH_PZC close to 6.43. After grinding, the material is tested for Methylene Blue sorption at pH 10.5: sorption capacity reaches 1.70 mmol MB g^-1 (synergistic effect of the precursors). The sorption isotherms are fitted by both Langmuir and Sips eqs. MB sorption increases with temperature: the sorption is endothermic (∆H°: 12.9 kJ mol^-1), with positive entropy (∆S°: 125 J mol^-1 K^-1). Uptake kinetics are controlled by agitation speed (optimum ≈200 rpm) and resistance to intraparticle diffusion. The profiles are strongly affected by the mode of agitation: the equilibrium time (≈180 min) is reduced to 20-30 min under sonication (especially at frequency: 80 kHz). The mode of agitation controls the best fitting equation: pseudo-first order rate agitation for mechanical agitation contrary to pseudo-second order rate under sonication. The sorption of MB is poorly affected by ionic strength (loss <6 % in 45 g L^-1 NaCl solution). Desorption (faster than sorption) is completely achieved using 0.7 M HCl solution. At the sixth recycling, the loss in sorption is close to 5 % (≈ decrease in desorption efficiency). The process is successfully applied for the treatment of MB-spiked industrial solution: the color index decreases by >97 % with a sorbent dose close to 1 g L^-1; a higher dose is required for maximum reduction of the COD (60 % at 3 g L^-1).

A Critical Review of Snail Shell Material Modification for Applications in Wastewater Treatment

Sea material is becoming increasingly popular and widely used as an adsorbent in wastewater treatment. Snail shell, a low-cost and natural animal waste material, has been shown to have a high calcium content (>99%) and a large potential surface area for the development of sustainable adsorbents. This paper presents a novel synthesis of methods for using snail shell absorbent materials in the treatment of wastewater containing heavy metals, textile dyes, and other organic substances. Modified biochar made from snail shells has gained popularity in recent years due to its numerous benefits. This paper discusses and analyzes modification methods, including impregnating with supplements, combining other adsorbents, synthesis of hydroxyapatite, co-precipitation, and the sol-gel method. The analysis of factors influencing adsorption efficiency revealed that pH, contact time, temperature, initial concentration, and adsorbent dose all have a significant impact on the adsorption process. Future research directions are also discussed in this paper as a result of presenting challenges for current snail adsorbents.

Trichoderma asperellum as a novel source to prepare chitooligosaccharides by enzymatic hydrolysis and its antimicrobial activity

Chitooligosaccharides (COS), an important biological functional component, are mainly extracted from marine products, but its raw materials are currently facing challenges such as marine resources pollution and demineralization. This study aimed to explore Trichoderma asperellum as a novel source to prepare COS. The COS were prepared by the enzymatic degradation of chitosan from T. asperellum, and single factor experiment and orthogonal designs were used to optimize the enzymatic conditions for the preparation of COS. The composition of COS was performed by thin-layer chromatography, high-performance liquid chromatography, and matrix-assisted laser desorption ionization time-of-flight mass spectrometry. The results showed that the degree of deacetylation of T. asperellum chitosan was 87.59%, and its enzymatic hydrolysis yield was 89.37 % under optimized extraction conditions. Moreover, the composition of COS in T. asperellum included chitotriose, chitopentaose, and chitohexaose. Compared with shrimp shells, COS prepared from T. asperellum showed stronger antibacterial properties against Escherichia coli, Staphylococcus aureus, Bacillus subtilis, and Salmonella bacilli.

Preparation of polyethyleneimine-modified chitosan/Ce-UIO-66 composite hydrogel for the adsorption of methyl orange

In this work, a polyethyleneimine-modified chitosan/Ce-UIO-66 composite hydrogel (PEI-CS/Ce-UIO-66) was prepared using the ex-situ blend method. The synthesized composite hydrogel was characterized by SEM, EDS, XRD, FTIR, BET, XPS, and TG techniques, while the zeta potential was recorded for sample analysis. The adsorbent performance was studied by conducting adsorption experiments using methyl orange (MO), which showed that PEI-CS/Ce-UIO-66 exhibited excellent MO adsorption properties (900.5 ± 19.09 mg/g). The adsorption kinetics of PEI-CS/Ce-UIO-66 could be explained by the pseudo-second-order kinetic model, and its isothermal adsorption followed the Langmuir model. Thermodynamics showed that the adsorption was spontaneous and exothermic at low temperatures. MO could interact with PEI-CS/Ce-UIO-66 via electrostatic interaction, π-π stacking, and hydrogen bonding. The results indicated that the PEI-CS/Ce-UIO-66 composite hydrogel could potentially be used for the adsorption of anionic dyes.

Green and Superior Adsorbents Derived from Natural Plant Gums for Removal of Contaminants: A Review

The ubiquitous presence of contaminants in water poses a major threat to the safety of ecosystems and human health, and so more materials or technologies are urgently needed to eliminate pollutants. Polymer materials have shown significant advantages over most other adsorption materials in the decontamination of wastewater by virtue of their relatively high adsorption capacity and fast adsorption rate. In recent years, "green development" has become the focus of global attention, and the environmental friendliness of materials themselves has been concerned. Therefore, natural polymers-derived materials are favored in the purification of wastewater due to their unique advantages of being renewable, low cost and environmentally friendly. Among them, natural plant gums show great potential in the synthesis of environmentally friendly polymer adsorption materials due to their rich sources, diverse structures and properties, as well as their renewable, non-toxic and biocompatible advantages. Natural plant gums can be easily modified by facile derivatization or a graft polymerization reaction to enhance the inherent properties or introduce new functions, thus obtaining new adsorption materials for the efficient purification of wastewater. This paper summarized the research progress on the fabrication of various gums-based adsorbents and their application in the decontamination of different types of pollutants. The general synthesis mechanism of gums-based adsorbents, and the adsorption mechanism of the adsorbent for different types of pollutants were also discussed. This paper was aimed at providing a reference for the design and development of more cost-effective and environmentally friendly water purification materials.

Role of emerging chitosan and zeolite-modified adsorbents in the removal of nitrate and phosphate from an aqueous medium: A comprehensive perspective

Due to industrialization and population growth, freshwater supplies are diminishing and becoming impure with high organic pollutant concentrations such as nitrate and phosphate, which shows a high adverse impact on aquatic and human lives. In drinking water sources, particularly groundwater, nitrate is considered as one of the major pollutants which causes methemoglobinemia (in newborn infants), carcinogenic activities and diabetes. Excess concentration of phosphate leads to eutrophication and death of aquatic species due to reduced dissolved oxygen content. Therefore, all countries must implement highly effective technologies for treating wastewater. Chitosan and zeolite are naturally occurring and cost-effective adsorbent materials with a higher surface area that exhibit greater nitrate and phosphate adsorption. Surface modification of chitosan and zeolite increases the adsorption capacity of adsorbents for the removal of both anions selectively. This paper reviews the current development of modified chitosan and zeolite adsorbents for anion adsorption, with an emphasis on modification by zero and multivalent metals and metal oxides, different surfactants, biomass-derived carbon, and natural and synthetic polymers. Multiple adsorption parameters, optimum adsorption condition, adsorption mechanism, regeneration study, research gap and future aspects have been explained for further research work.

Bimetallic Fe/Al-MOF for the adsorptive removal of multiple dyes: optimization and modeling of batch and hybrid adsorbent-river sand column study and its application in textile industry wastewater

Bimetallic metal organic framework (MOF) has garnered interest over the years with its applications in industrial wastewater treatment. In this work, Fe-Al-1,4-benzene-dicarboxylic acid (FeAl(BDC)) MOF was synthesized, and adsorptive removal of Rhodamine B dye in batch and unique hybrid FeAl (BDC)-river sand fixed-bed column was studied. The experimental data from the batch studies corroborated well with the pseudo-second-order (PSO) (R²: 0.97) and Freundlich adsorption isotherm models (R²: 0.98) and achieved a maximum adsorption capacity of 48.59 mg/g in 90 min. Furthermore, a fixed-bed column study was conducted to assess the effect of varying flow rate (2, 5, 8 mL/min), bed height (5, 9, 13 cm), and feed concentration (10, 20, 30 mg/L) on the adsorption performance of FeAl(BDC) in continuous mode of operation. A uniform mixture of river sand and FeAl(BDC) by weight ratio (9:1) was packed into the column. The sand-FeAl(BDC) fixed-bed column could achieve the maximum adsorption capacity (q_exp) of 113.05 mg/g at a 5 mL/min flow rate, feed concentration of 20 mg/L, and a bed height of 13 cm. The experimental data of the column study were successfully fitted well with BDST, Thomas (q_cal: 114.94 mg/g), Yoon-Nelson, and dose-response models (q_cal: 113.41 mg/g) and R²: 0.97-0.99. The fitting parameter values from the BDST model raise the scope of viable upscaling of the fixed-bed column. In all, it is proposed that these river sand-FeAl(BDC)-based filters can be widely used in areas facing critical contamination and in poor communities with a high demand for water.

Adsorption and removal of direct red 31 by Cu-MOF: optimization by response surface

Cu(PABA) is a Cu-based MOF material assembled from Cu²⁺ and the organic ligand p-aminobenzoic acid (PABA). Cu (PABA) was synthesized by a solvothermal method, characterized and applied to the adsorption of direct red 31 dye (DR-31). The effects of pH, DR-31 concentration and temperature on the adsorption performance of Cu(PABA) were investigated. The adsorption kinetics were analyzed by pseudo-first-order, pseudo-second-order and intra-particle diffusion models, and the adsorption equilibrium data was fitted by Langmuir and Freundlich isotherm models. The pseudo-first-order kinetics and Langmuir model satisfactorily described the adsorption kinetics and adsorption equilibrium, respectively. The maximum adsorption capacity of Cu(PABA) for DR-31 dye at room temperature was 1,244.8 mg/g, as calculated using the Langmuir adsorption isotherm model. By response surface methodology (RSM), the optimal adsorption was found at pH value of 10.9, DR-31 dye concentration of 216.6 mg/L, and temperature of 27 °C, and the removal rate was as high as 99.4%. Therefore, Cu(PABA) can be used as an efficient adsorbent for removing DR-31 dye from aqueous solution.

Comparative Evaluation of the Adsorption Performance of Citric Acid-Treated Peels of Trapa natans and Citrullus lanatus for Cationic Dyes Degradation from Water

Various chemicals were explored in chemical combinations with two selected agrowastes in order to optimize, enhance, and improve their biosorption potential for the optimal and effective eradication of noxious, carcinogenic, and malignant cationic and basic dyes from wastewater. In this project, environmentally safe, economic, inexpensive, and widely available peels of Trapa natans (TP) and Citrullus lanatus (CP) were collected, dried, and pretreated with citric acid, revealing promising results. FT-IR and SEM characterizations of chemically changed biosorbents (C-TP and C-CP) have evidenced the presence of more secondary adsorption sites on their surfaces. These acid-modified biosorbents were employed to eliminate the hazardous and toxic basic dyes such as Rhodamine B (RAD) and Brilliant Green Dye (BLG) in batch mode processing. The Langmuir model was best fitted to equilibrium experimental data as compared to Freundlich and Temkin isothermal mathematical models with Qmax of 15.63 and 27.55 mg/g for RAD using C-TP and C-CP, respectively, whereas, for BLG on C-TP and C-CP, it was 128 and 189 mg/g, respectively. Therefore, the mechanism is related to chelation and ion exchange modes between adsorbate molecules and adsorbent surfaces, leading to homogeneous and monolayer adsorption and following pseudo-2nd-order kinetics in the best way. Thermodynamic parameters such as ΔG0, ΔS0, ΔH0, and ΔE0 are determined statistically for the adsorption performance of both novel chemically mutant biosorbents, which reflect that biosorption mechanisms are exothermic as well as spontaneous.

Protective, Biostimulating, and Eliciting Effects of Chitosan and Its Derivatives on Crop Plants

Chitosan is a biodegradable and biocompatible polysaccharide obtained by partial deacetylation of chitin. This polymer has been gaining increasing popularity due to its natural origin, favorable physicochemical properties, and multidirectional bioactivity. In agriculture, the greatest hopes are raised by the possibility of using chitosan as a biostimulant, a plant protection product, an elicitor, or an agent to increase the storage stability of plant raw materials. The most important properties of chitosan include induction of plant defense mechanisms and regulation of metabolic processes. Additionally, it has antifungal, antibacterial, antiviral, and antioxidant activity. The effectiveness of chitosan interactions is determined by its origin, deacetylation degree and acetylation pattern, molecular weight, type of chemical modifications, pH, concentration, and solubility. There is a need to conduct research on alternative sources of chitosan, extraction methods, optimization of physicochemical properties, and commercial implementation of scientific progress outcomes in this field. Moreover, studies are necessary to assess the bioactivity and toxicity of chitosan nanoparticles and chitosan conjugates with other substances and to evaluate the consequences of the large-scale use thereof. This review presents the unique properties of chitosan and its derivatives that have the greatest importance for plant production and yield quality as well as the benefits and limitations of their application.

Optimization of chitosan/tannic acid@ ZnFe layered double hydroxide bionanocomposite film for removal of reactive blue 4 using a response surface methodology

Layered double hydroxides (LDH) are great adsorbents for anionic pollutants, but are in a powder form that leads to challenges in solid-liquid separation, low hydraulic conductivity, and handling. Herein, novel bionanocomposite films containing chitosan (Cs), tannic acid (TA), and LDH were fabricated and applied for the removal of reactive blue 4 (RB4). A response surface methodology with Box-Behnken design was applied to study the effect of operating parameters (TA%: 0-20, LDH%: 0-20, pH: 5-9, adsorbent dosage: 0.5-1.5 g L^-1, time: 30-90 min) on RB4 dye removal (DR%). A quadratic regression equation was successfully developed to predict the response (R²: 0.95). The obtained optimized condition was TA%: 10, LDH%: 20, pH: 5, adsorbent dosage: 1.5 g L^-1, and time: 71 min that resulted in DR%: 98.2. The best-fitted adsorption isotherm and kinetic models were linear Langmuir and nonlinear pseudo-second-order models, respectively. The maximum capacity of adsorption for the optimized film was 406 mg g^-1. The obtained thermodynamic parameters implied that the process of adsorption was exothermic and spontaneous. The reusability studies showed that the DR% was decreased from 93% for the first cycle to 69%, 57%, and 56% for the second, third and fourth cycle, respectively.

Chitosan as a Tool for Sustainable Development: A Mini Review

New developments require innovative ecofriendly materials defined by their biocompatibility, biodegradability, and versatility. For that reason, the scientific society is focused on biopolymers such as chitosan, which is the second most abundant in the world after cellulose. These new materials should show good properties in terms of sustainability, circularity, and energy consumption during industrial applications. The idea is to replace traditional raw materials with new ecofriendly materials which contribute to keeping a high production rate but also reducing its environmental impact and the costs. The chitosan shows interesting and unique properties, thus it can be used for different purposes which contributes to the design and development of sustainable novel materials. This helps in promoting sustainability through the use of chitosan and diverse materials based on it. For example, it is a good sustainable alternative for food packaging or it can be used for sustainable agriculture. The chitosan can also reduce the pollution of other industrial processes such as paper production. This mini review collects some of the most important advances for the sustainable use of chitosan for promoting circular economy. Hence, the present review focuses on different aspects of chitosan from its synthesis to multiple applications.

Removal of Acidic Organic Ionic Dyes from Water by Electrospinning a Polyacrylonitrile Composite MIL101(Fe)-NH2 Nanofiber Membrane

A nanofiber metal–organic framework filter, a polyacrylonitrile (PAN) nanofiber membrane composite with an iron/2-amino-terephthalic acid-based metal–organic framework (MIL101(Fe)-NH₂), was prepared by one-step electrospinning. MIL101(Fe)-NH₂ was combined into the polymer nanofibers in situ. PAN-MIL101(Fe)-NH₂ composite nanofiber membranes (NFMs) were prepared from a homogeneous spinning stock containing MIL101(Fe)-NH₂ prebody fluid and PAN. Crystallization of MIL101(Fe)-NH₂ and solidification of the polymer occurred simultaneously during electrospinning. The PAN-MIL101(Fe)-NH₂ composite NFM showed that MIL101(Fe)-NH₂ was uniformly distributed throughout the nanofiber and was used to adsorb and separate acidic organic ionic dyes from the aqueous solution. The results of Fourier transform infrared spectroscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction analysis showed that MIL101(Fe)-NH₂ crystals were effectively bonded in the PAN nanofiber matrix, and the crystallinity of MIL101(Fe)-NH₂ crystals remained good, while the distribution was uniform. Owing to the synergistic effect of PAN and the MIL101(Fe)-NH₂ crystal, the PAN-MIL101(Fe)-NH₂ composite NFM showed a fast adsorption rate for acidic ionic dyes. This study provides a reference for the rapid separation and purification of organic ionic dyes from wastewater.

Preparation of Needleless Electrospinning Polyvinyl Alcohol/Water-Soluble Chitosan Nanofibrous Membranes: Antibacterial Property and Filter Efficiency

Electrospinning is an efficient method of producing nanofibers out of polymers that shows a great potential for the filtration territory. Featuring water-soluble chitosan (WS-CS), a low-pollution process and a self-made needleless machine, PVA/WS-CS nanofibrous membranes were prepared and evaluated for nanofiber diameter, bacteriostatic property, filtration efficiency, pressure drop, and quality factor. Test results indicate that the minimal fiber diameter was 216.58 ± 58.15 nm. Regardless of the WS-CS concentration, all of the PVA/WS-CS nanofibrous membranes attained a high porosity and a high water vapor transmission rate (WVTR), with a pore size of 12.06–22.48 nm. Moreover, the membranes also exhibit bacteriostatic efficacy against Staphylococcus aureus, an optimal quality factor of 0.0825 Pa⁻¹, and a filtration efficiency as high as 97.0%, that is 72.5% higher than that of common masks.

Superamphiphilic Chitosan Cryogels for Continuous Flow Separation of Oil-In-Water Emulsions

Chitosan is a typical hydrophilic biomass building block widely used in material science and engineering. However, its intrinsic amphiphilicity has been seldom noted so far. Herein, a series of glutaraldehyde-crosslinked chitosan cryogels with superamphiphilicity are fabricated at moderately frozen conditions through a freezing-thawing process. The micron-sized porous cryogel samples display a 0° contact angle toward both water and oil, 0° water contact angle under oil, and over 120° oil contact angle underwater. By comparing the wetting behavior of the tablet compressed by pure chitosan powders, the superamphiphilicity of the chitosan sample is proven to be independent on crosslinkers. This special wettability endows the chitosan cryogels with high separation efficiency for various surfactant-stabilized oil-in-water emulsions under continuous flow mode driven by gravity as well as a peristaltic pump.

Chitosan functionalized with N,N-(2-aminoethyl)pyridinedicarboxamide for selective adsorption of gold ions from wastewater

The recovery of gold from wastewater has always been a research hotspot. Here, a novel chitosan-based adsorbent (CS-DPDM) was successfully synthesized by functionalizing chitosan with (N, N-(2-aminoethyl))-2,6-pyridinedicarboxamide. The adsorbent was analyzed by fourier transform infrared spectroscopy (FT-IR), nuclear magnetic resonance spectroscopy (¹H NMR), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD) and zeta potential method (Zeta). To investigate the adsorption performance of CS-DPDM for Au(III), the effects of pH, temperature, adsorption time and initial concentration were discussed. The maximum adsorption capacity of CS-DPDM for Au(III) at pH 5.0 is 659.02 mg/g at 318 K. The adsorption is a spontaneous endothermic behavior, and the adsorption process follows the quasi-second-order kinetic and Langmuir isotherm models, indicating that a single layer of chemical adsorption may have occurred on the surface of the adsorbent. The competitive adsorption and repetitive experiments show that CS-DPDM has considerable selectivity and reusability for Au(III). X-ray photoelectron spectroscopy (XPS) results show that N and O functional groups adsorb Au(III) on the surface of CS-DPDM through electrostatic, chelation and reduction. These results indicate that CS-DPDM has broad application prospects in recovering gold ions from aqueous solutions.