Influence of cellulose nanocrystal addition on the production and characterization of bacterial nanocellulose

Enhancing the dispersibility of Gelidium amansii-derived microfibrillated cellulose through centrifugal fractionation

Hydrothermal pretreatment is useful for microfibrillated cellulose (MFC) preparation due to its safety, but the remaining hemicellulose might affect MFC properties. This study aimed to investigate the effect of centrifugation time on hemicellulose removal and the physicochemical properties of MFC obtained after hydrothermal pretreatment and micro-fibrillation. In this study, centrifugation was applied to the MFC suspension at varying duration times. Composition analysis and Fourier transform infrared spectra indicated that fractionated MFC has no hemicellulose content after 10, 20, and 30 min centrifugation. It also showed an approximately 5 times higher than 0.5 % g/g of initial solid concentration, indicated by a lower gel concentration point, than unfractionated MFC. Scanning electron microscope images of the fractionated MFC for 30 min (MFC2C) presented thin, long cellulose fibrils of 517 nm in average diameter and 635-10,000 nm in length that induced a slower sedimentation rate. MFC2C dispersion was also improved by autoclave sterilization by regulating cellulose structure, rheology, and crystallinity. As a result, MFC dispersibility can be enhanced by removing hemicellulose through simple centrifugation.

Upcycling Food By-products: Characteristics and Applications of Nanocellulose

Rising global food prices and the increasing prevalence of food insecurity highlight the imprudence of food waste and the inefficiencies of the current food system. Upcycling food by-products holds significant potential for mitigating food loss and waste within the food supply chain. Food by-products can be utilized to extract nanocellulose, a material that has obtained substantial attention recently due to its renewability, biocompatibility, bioavailability, and a multitude of remarkable properties. Cellulose nanomaterials have been the subject of extensive research and have shown promise across a wide array of applications, including the food industry. Notably, nanocellulose possesses unique attributes such as a surface area, aspect ratio, rheological behavior, water absorption capabilities, crystallinity, surface modification, as well as low possibilities of cytotoxicity and genotoxicity. These qualities make nanocellulose suitable for diverse applications spanning the realms of food production, biomedicine, packaging, and beyond. This review aims to provide an overview of the outcomes and potential applications of cellulose nanomaterials derived from food by-products. Nanocellulose can be produced through both top-down and bottom-up approaches, yielding various types of nanocellulose. Each of these variants possesses distinctive characteristics that have the potential to significantly enhance multiple sectors within the commercial market.

Current advances of nanocellulose application in biomedical field

Nanocellulose (NC) is a natural fiber that can be extracted in fibrils or crystals form from different natural sources, including plants, bacteria, and algae. In recent years, nanocellulose has emerged as a sustainable biomaterial for various medicinal applications including drug delivery systems, wound healing, tissue engineering, and antimicrobial treatment due to its biocompatibility, low cytotoxicity, and exceptional water holding capacity for cell immobilization. Many antimicrobial products can be produced due to the chemical functionality of nanocellulose, such disposable antibacterial smart masks for healthcare use. This article discusses comprehensively three types of nanocellulose: cellulose nanocrystals (CNC), cellulose nanofibrils (CNF), and bacterial nanocellulose (BNC) in view of their structural and functional properties, extraction methods, and the distinctive biomedical applications based on the recently published work. On top of that, the biosafety profile and the future perspectives of nanocellulose-based biomaterials have been further discussed in this review.

Efficient microbial cellulose/Fe3O4 nanocomposite for photocatalytic degradation by advanced oxidation process of textile dyes

Fenton-type advanced oxidative processes (AOP) have been employed to treat textile dyes in aqueous solution and industrial effluent. The work focused on assisting the limitations still presented by the Fenton process regarding the use of suspended iron catalysts. Soon, a nanocomposite of bacterial cellulose (BC) and magnetite (Fe₃O₄) was developed. It has proven to be superior to those available in the literature, exhibiting purely catalytic properties and high reusability. Its successful production was verified through analytical characterization, while its catalytic potential was investigated in the treatment of different textile matrices. In initial tests, the photo-Fenton process irradiated and catalyzed by sunlight and BC/Fe₃O₄ discolored 92.19% of an aqueous mixture of four textile dyes. To improve the efficiency, the design of experiments technique evaluated the influence of the variables pH, [H₂O₂], and the number of BC/Fe₃O₄ membranes. 99.82% of degradation was obtained under optimized conditions using pH 5, 150 mg L^-1 of H₂O₂, and 11 composite membranes. Reaction kinetics followed a pseudo-first-order model, effectively reducing the organic matter (COD = 83.24% and BOD = 88.13%). The composite showed low iron leaching (1.60 ± 0.08 mg L^-1) and high stability. It was recovered and reused for 15 consecutive cycles, keeping the treatment efficiency at over 90%. As for the industrial wastewater, the photo-Fenton/sunlight/BC/Fe₃O₄ system showed better results when combined with the physical-chemical coagulation/flocculation process previously used in the industry's WWTP. Together they reduced COD by 77.77%, also meeting the color standards (DFZ scale) for the wavelengths of 476 nm (<3 m^-1), 525 nm (<5 m^-1), and 620 nm (<7 m^-1). Thus, the results obtained demonstrated that employing the BC/Fe₃O₄ composite as an iron catalyst is a suitable alternative to materials employed in suspension. This is mainly due to the high catalytic activity and power of reuse, which will reduce treatment costs.

Original nanostructured bacterial cellulose/pyrite composite: Photocatalytic application in advanced oxidation processes

The development of an original catalytic composite of bacterial cellulose (BC) and pyrite (FeS₂) for environmental application was the objective of this study. Nanoparticles of the FeS₂ were synthesized from the hydrothermal method and immobilized on the BC structure using ex situ methodology. In the BC, the FTIR and XRD analyzes showed the absorption band associated with the Fe-S bond and crystalline peaks attributed to the pyrite. Thus, the immobilization of the iron particles on the biopolymer was proven, producing the composite BC/FeS₂. The use of the SEM technique also ratifies the composite production by identifying the fibrillar structure morphology of the cellulose covered by FeS₂ particles. The total iron concentration was 54.76 ± 1.69 mg L^-1, determined by flame atomic absorption analysis. TG analysis and degradation tests showed respectively the thermal stability of the new material and its high catalytic potential. A multi-component solution of textile dyes was used as the matrix to be treated via advanced oxidative processes. The composite acted as the catalyst for the Fenton and photo-Fenton processes, with degradations of 52.87 and 96.82%, respectively. The material proved stability by showing low iron leaching (2.02 ± 0.09 and 2.11 ± 0.11 mg L^-1 for the respective processes). Thus, its high potential for reuse is presumed, given the remaining concentration of this metal in the BC. The results showed that the BC/FeS₂ composite is suitable to solve the problems associated with using catalysts in suspension form.

Enhancing thermal conductivity and chemical protection of bacterial cellulose/silver nanowires thin-film for high flexible electronic skin

Silver nanowires (AgNWs) thin films have emerged as a promising next-generation flexible electronic device. However, the current AgNWs thin films are often plagued by high AgNWs-AgNWs contact resistance and poor long-term stability. Here, to enhance the AgNWs stability on the surface of bacterial cellulose (BC), a novel flexible high conductivity thin-film was prepared by spin-coating a layer of polyvinyl alcohol (PVA) on the BC/AgNWs (BA) film. Firstly, BC film with high uniformity to better fit the AgNWs was obtained. It is observed that inadequately protected AgNWs can be corroded when AgNWs together with PVA were attached to the BC surface (BAP film), Yet, a layer of PVA was spin-coated on the surface of BA film, the BC/AgNWs/spin-coated 0.5 % PVA (BASP) thin-film (10.1 μm) exhibits that the PVA interfacial protective layer effectively mitigated the intrinsic incompatibility of BC with AgNWs as well as external corrosion (Na₂S for 3 h) and immobilization of AgNWs, thus having a low conductive sheet resistance of 0.42 Ω/sq., which was better than most of the AgNWs-containing conductive materials reported so far. In addition, the resistance of the BASP thin-film changed little after 10,000 bending cycles, and the conductivity remained stable over BC directly immersed in 0.5 % PVA/AgNWs. This "soft" conductive material can be used to manufacture a new generation of electronic skin.

Preparation of High-Solid Microfibrillated Cellulose from Gelidium amansii and Characterization of Its Physiochemical and Biological Properties

Microfibrillated cellulose (MFC) is a valuable material with wide industrial applications, particularly for the food and cosmetics industries, owing to its excellent physiochemical properties. Here, we prepared high-solid microfibrillated cellulose (HMFC) from the centrifugation of Gelidium amansii-derived MFC right after fibrillation. Dispersion properties, morphology, and structural changes were monitored during processing. HMFC has a five-fold higher solid concentration than MFC without significant changes to dispersion properties. SEM images and FTIR spectra of HMFC revealed a stable surface and structure against centrifugal forces. HMFC exhibited 2,2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) radical scavenging activity, although it could not scavenge 2,2-diphenyl-1-picrylhydrazyl (DPPH). Moreover, HMFC inhibited the generation of LPS-induced excessive nitrite and radial oxygen species in murine macrophage RAW264.7 cells. Additionally, HMFC suppressed LPS-induced Keap-1 expression in the cytosol but did not alter iNOS expression. HMFC also attenuated the UVB-induced phosphorylation of p38, c-Jun N-terminal kinase (JNK) 1/2, and extracellular-signal-regulated kinase (ERK) 1/2, as well as the phosphorylation of c-Jun in the immortalized human skin keratinocyte HaCaT cells. Therefore, the application of centrifugation is suitable for producing high-solid MFC as a candidate material for anti-inflammatory and anti-oxidative marine cosmeceuticals.

Diverse Pathways of Engineered Nanoparticle-Induced NLRP3 Inflammasome Activation

With the rapid development of engineered nanomaterials (ENMs) in biomedical applications, their biocompatibility and cytotoxicity need to be evaluated properly. Recently, it has been demonstrated that inflammasome activation may be a vital contributing factor for the development of biological responses induced by ENMs. Among the inflammasome family, NLRP3 inflammasome has received the most attention because it directly interacts with ENMs to cause the inflammatory effects. However, the pathways that link ENMs to NLRP3 inflammasome have not been thoroughly summarized. Thus, we reviewed recent findings on the role of major ENMs properties in modulating NLRP3 inflammasome activation, both in vitro and in vivo, to provide a better understanding of the underlying mechanisms. In addition, the interactions between ENMs and NLRP3 inflammasome activation are summarized, which may advance our understanding of safer designs of nanomaterials and ENM-induced adverse health effects.

Exploration of a novel and efficient source for production of bacterial nanocellulose, bioprocess optimization and characterization

The demand for bacterial nanocellulose is expected to rise in the coming years due to its wide usability in many applications. Hence, there is a continuing need to screen soil samples from various sources to isolate a strain with a high capacity for bacterial nanocellulose production. Bacillus sp. strain SEE-12, which was isolated from a soil sample collected from Barhiem, Menoufia governorate, Egypt, displayed high BNC production under submerged fermentation. Bacillus sp. strain SEE-12 was identified as Bacillus tequilensis strain SEE-12. In static cultures, BNC was obtained as a layer grown in the air liquid interface of the fermentation medium. The response surface methodology was used to optimise the process parameters. The highest BNC production (22.8 g/L) was obtained using 5 g/L peptone, 5 g/L yeast extract, 50%, v/v Cantaloupe juice, 5 g/L Na₂HPO₄, 1.5 g/L citric acid, pH 5, medium volume of 100 mL/250 mL conical flask, inoculum size 5%, v/v, temperature 37 °C and incubation time 6 days. The BNC was purified and characterized by scanning electron microscopy (SEM), Energy-dispersive X-ray (EDX) spectroscopy, differential scanning calorimetry (DSC), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and transmission electron microscopy (TEM).