An insight into powder entrainment and drug delivery mechanisms from a modified Rotahaler®

Predicting in vitro lung deposition behavior of combined dry powder inhaler via rheological properties

Dry powder inhaler (DPI) for pulmonary delivery is currently the primary treatment for asthma and COPD (chronic obstructive pulmonary disease), an increasing number of combined DPIs (containing two or more drugs in one inhaler) have been developed to complement the effect of single DPIs. Based on our previous studies, the rheological properties can be a potential tool used to predict the in vitro lung deposition behavior of DPI formulations. However, it is unknown whether such a prediction model is suitable for combination systems. Therefore, this study aimed to verify the applicability of using powder rheological properties to predict in vitro drug deposition behavior in combined DPI formulations. Two drugs (fluticasone propionate and salmeterol xinafoate) and their combination of DPI formulations were prepared using fine lactose content (in the range of 1%-20%) as a variable. The physicochemical properties of the powder mixtures such as particle size and content uniformity were characterized. The rheological properties of the powder mixtures were measured by FT4 rheometer, the aerodynamic behavior of the DPI formulations was evaluated by a new generation impactor (NGI), and the effect of flowability and adhesion on the deposition of the fine particle fraction (FPF) was investigated by principal component analysis (PCA). The results showed that the combined DPI formulations with larger particle interaction forces have certain differences from the aerodynamic behavior of the single DPI formulations. The regularity of rheological properties affecting FPF revealed in single DPI is still applicable to combined DPI, the parameters basic flowability energy (BFE), representing flowability, and flow factor (ff), Cohesion representing adhesion, can be well linearly related to the FPF. The results of the principal component analysis showed that better flowability and suitable adhesion contributed to higher in vitro deposition of the drug in the formulation, and the contribution of adhesion (75.42%) was greater than that of flowability (24.58%). In conclusion, rheological properties is an effective tool for predicting the deposition behavior of DPI not only in single but also in combined DPIs.

A Quality by Design Framework for Capsule-Based Dry Powder Inhalers

Capsule-based dry powder inhalers (cDPIs) are widely utilized in the delivery of pharmaceutical powders to the lungs. In these systems, the fundamental nature of the interactions between the drug/formulation powder, the capsules, the inhaler device, and the patient must be fully elucidated in order to develop robust manufacturing procedures and provide reproducible lung deposition of the drug payload. Though many commercially available DPIs utilize a capsule-based dose metering system, an in-depth analysis of the critical factors associated with the use of the capsule component has not yet been performed. This review is intended to provide information on critical factors to be considered for the application of a quality by design (QbD) approach for cDPI development. The quality target product profile (QTPP) defines the critical quality attributes (CQAs) which need to be understood to define the critical material attributes (CMA) and critical process parameters (CPP) for cDPI development as well as manufacturing and control.

Exploring the potential influence of drug charge on downstream deposition behaviour of DPI powders

Dry powder inhaler (DPI) development is limited by the time- and labor-consuming in vitro lung deposition test. It's highly desirable to find an easy tool for DPI formulation screening. Dynamic powder rheological properties seem to present many advantages, however, the adoptability needs to be verified. Drug charge is an important parameter especially for DPI formulation design but how it affects the process of pulmonary drug delivery is unavailable. Therefore, the objective of this study is to explore the influence of drug charge on DPI powders, further testing the potentials of powder properties for downstream deposition behavior prediction. Taking five differently charged drugs as model, influence of drug charge on uniformity, rheological and aerodynamic properties of the mixtures were investigated systemically. It was found that mometasone furoate with near neutral charge presented better content homogeneity, while significantly decreased recovery was noted for charged drugs, such as positively charged drug (salbutamol sulphate and indacaterol maleate) mixtures and negatively charged drug (budesonide and fluticasone propionate) mixtures. Moreover, drug charge also influenced flowability and cohesion of their admixture with lactose. As for the downstream deposition, neutral drugs presented higher fine particle fraction (FPF), followed by positively charged drugs and negatively charged drugs. Good correlations between basic flowability energy, aeration energy, Permeability and FPF were established irrespective of different drugs. Principal component analysis results suggested flowability had a greater influence on FPF when mixtures were less cohesive. In conclusion, this study demonstrated drug charge can influence physicochemical, rheological and aerodynamic properties of the admixture, and DPIs' dynamic properties could be used as potential tools to predict downstream deposition with good accuracy.

Microstructural characterization of carrier-based dry powder inhalation excipients: Insights and guidance

The growing interest in development of dry powder inhalation (DPI) products raises a need for development of standard testing methods and specifications for DPI excipients. The pharmaceutical industry, meanwhile, yet lacks compendial guidance on this topic. Despite of the complexity of interactions taking place in DPI systems and the large number and variety of interplaying factors, understanding of key determinants of performance (critical quality attributes) of DPI excipients have considerably developed over the past years. In light of the current knowledge in this area, this article provides technical guidance and insights on testing and quality control of carrier-based-DPI excipients. These excipients are, typically, blends of coarse, carrier particles and fine, performance-modulating particles. The article explores techniques used for measurement of key microstructural attributes, namely the particle size distribution, the porosity and the particle surface roughness, the particle shape, rheological properties, and the permeability, of these excipients. The technical relevance of each measurement to the functionality of the excipients is critically discussed. In this regard, caveats concerning use of some measurements and data analysis procedures are raised. The guidance lends itself for compendial adoption.

Optical diagnostics studies of air flow and powder fluidisation in Nexthaler®. Part II: Use of fluorescent imaging to characterise transient release of fines from a dry powder inhaler

The fine particle fraction is a key indicator of therapeutic effectiveness of inhaled pharmaceutical aerosols. This paper presents a fluorescence imaging technique to visualise and characterise the emission of active pharmaceutical ingredient (API) fines in model formulations containing coarse lactose carrier and 1.5-2 μm diameter fluorescent microspheres (model API fines). A two-camera arrangement was used to acquire simultaneous images of spatial and temporal distribution of model API fines and fluidised powder formulation near the mouthpiece exit of a DPI. Digital image analysis showed that the model API fines were released along with the bulk of the powder dose. More rapidly accelerating airflows were found to cause earlier release of API fines. The fluorescence imaging technique analyses a substantial fraction of the aerosol plume and was found to provide effective time-resolved characterisation of the de-aggregation and release of API fines with consistent results across a wide range of model API concentrations. Future studies should demonstrate the usefulness of the fluorescence imaging technique across different formulations and DPI devices.

Relationships between surface coverage ratio and powder mechanics of binary adhesive mixtures for dry powder inhalers

The aim of this paper was to study relationships between the content of fine particles and the powder mechanics of binary adhesive mixtures and link these relationships to the blend state. Mixtures with increasing amounts of fine particles (increasing surface coverage ratios (SCR)) were prepared using Lactopress SD as carrier and micro particles of lactose as fines (2.7 µm). Indicators of unsettled bulk density, compressibility and flowability were derived and the blend state was visually examined by imaging. The powder properties studied showed relationships to the SCR characterised by stages. At low SCR, the fine particles predominantly gathered in cavities of the carriers, giving increased bulk density and unchanged or improved flow. Thereafter, increased SCR gave a deposition of particles at the enveloped carrier surface with a gradually more irregular adhesion layer leading to a reduced bulk density and a step-wise reduced flowability. The mechanics of the mixtures at a certain stage were dependent on the structure and the dynamics of the adhesion layer and transitions between the stages were controlled by the evolution of the adhesion layer. It is advisable to use techniques based on different types of flow in order to comprehensively study the mechanics of adhesive mixtures.

The Relationship Between the Permeability and the Performance of Carrier-Based Dry Powder Inhalation Mixtures: New Insights and Practical Guidance

The permeability of a powder bed reflects its particle size distribution, shape, packing, porosity, cohesivity, and tensile strength in a manner relevant to powder fluidization. The relationship between the permeability and the performance of carrier-based dry powder inhalation (DPI) mixtures has, however, aroused controversy. The current study sought to gain new insights into the relationship and to explore its potential applications. We studied eight lactose materials as DPI carriers. The carriers covered a broad permeability range of 0.42-13.53 D and moreover differed in particle size distribution, particle shape, crystal form, and/or porosity. We evaluated the performance of inhalation mixtures of each of these carriers and fluticasone propionate after aerosolization from an Aerolizer®, a model turbulent-shear inhaler, at a flow rate of 60 L/min. Starting from the high permeability side, the inhalation mixture performance increased as the carrier permeability decreased until optimum performance was reached at permeability of ~ 3.2 D. Increased resistance to air flow strengthens aerodynamic dispersion forces. The inhalation mixture performance then decreased as the carrier permeability further decreased. Very high resistance to air flow restricts powder dispersion. The permeability accounted for effects of carrier size, shape, and macroporosity on the performance. We confirmed the relationship by analysis of two literature permeability-performance datasets, representing measurements that differ from ours in terms of carrier grades, drug, technique used to determine permeability, turbulent-shear inhaler, and/or aerosolization flow rate. Permeability provides useful information that can aid development of DPI mixtures for turbulent-shear inhalers. A practical guidance is provided.

The Effects of Relative Humidity on the Flowability and Dispersion Performance of Lactose Mixtures

The flowability and dispersion behavior are two important physicochemical properties of pharmaceutical formulations for dry powder inhalers (DPIs). They are usually affected by the environmental conditions, such as temperature and relative humidity (RH). However, very few studies have been focused on the relationship between the two properties and their dependence on RH during storage. In this research, model pharmaceutical formulations were prepared using mixtures of coarse and fine lactose. The fractions of fines in the mixtures were 0%, 5%, 10%, and 20%, respectively. These blends were stored at four different RH levels, 0%, 30%, 58%, and 85%, for 48 h. The FT4 Powder Rheometer was used to evaluate the powder flowability, and the Malvern Spraytec^® laser diffraction system was employed to assess the powder dispersion performance. The results indicated that both the flow and dispersion properties of lactose blends deteriorate after being stored at 85% RH, but improved after being conditioned at 58% RH. The fine particle fractions (FPFs) of the blends with 5% and 10% fine fractions and the as-received coarse lactose decreased when they were conditioned at 30% RH. For the blend with 20% fine fraction, a high RH during storage (i.e., 85% RH) affected the dispersion property, but had a limited influence on its flowability, while, for the coarse lactose powder, the different RH conditions affected its flowability, but not the dispersion results. A strong correlation between the powder flowability and its dispersion performance was found.

Optimizing the Entrainment Geometry of a Dry Powder Inhaler: Methodology and Preliminary Results

PURPOSE

For passive dry powder inhalers (DPIs) entrainment and emission of the aerosolized drug dose depends strongly on device geometry and the patient's inhalation manoeuvre. We propose a computational method for optimizing the entrainment part of a DPI. The approach assumes that the pulmonary delivery location of aerosol can be determined by the timing of dose emission into the tidal airstream.

METHODS

An optimization algorithm was used to iteratively perform computational fluid dynamic (CFD) simulations of the drug emission of a DPI. The algorithm seeks to improve performance by changing the device geometry. Objectives were to achieve drug emission that was: A) independent of inhalation manoeuvre; B) similar to a target profile. The simulations used complete inhalation flow-rate profiles generated dependent on the device resistance. The CFD solver was OpenFOAM with drug/air flow simulated by the Eulerian-Eulerian method.

RESULTS

To demonstrate the method, a 2D geometry was optimized for inhalation independence (comparing two breath profiles) and an early-bolus delivery. Entrainment was both shear-driven and gas-assisted. Optimization for a delay in the bolus delivery was not possible with the chosen geometry.

CONCLUSIONS

Computational optimization of a DPI geometry for most similar drug delivery has been accomplished for an example entrainment geometry.