Texture and surface feature-mediated striking improvements on multiple direct compaction properties of Zingiberis Rhizoma extracted powder by coprocessing with nano-silica

Fingerprinting of physical manufacturing properties of different acids for effervescent systems

The study aimed to fingerprint the physical manufacturing properties of five commonly used acid sources in effervescent systems for designing the formulation and process of such systems. The hygroscopicity, texture properties, rheological torque, compressibility, tabletability, etc., were investigated to inspect 'powder direct compression (DC)' and 'wet granulation and compression' properties of citric (CA), tartaric (TA), malic (MA), fumaric (FA), and adipic acid (AA). The DC ability was evaluated by the SeDeM expert system. The results indicated that all acid powders failed to meet flowability requirements for DC, and plastic deformation dominated during compression. Furthermore, CA exhibited strong hygroscopicity and punch sticking, while MA demonstrated the best tabletability. TA had a large wet granulation space and was relatively the most suitable for DC. AA was extremely hygroscopic, and its flowability improved significantly as particle size increased. Finally, FA displayed the lowest hygroscopicity and ejection force as well as great compressibility and wet granulation space, and did not exhibit punch sticking, while the granule fragments dissolved slowly during disintegration. Generally speaking, the formulation or granulation affected the tabletability, indicating that pairing with other acids or suitable fillers could potentially improve its disadvantages. These multidimensional assessments effectively reduce the pre-exploration and enhance the efficiency of the development of effervescent systems.

Application of the SeDeM system for the preparation of antiparasitic tablets from mesquite flour for use in sheep

The use of herbal medicine to treat various diseases is becoming increasingly important as an alternative therapy. Numerous plants have been traditionally used for different purposes, including antiparasitic in humans and animals. Diseases caused by gastrointestinal parasites in ruminants, especially by the nematode Haemonchus contortus, cause large economic losses to the producers, whether by complications of the diseases or the cost of treatment. The main way of handling nematodiasis is by administering anthelmintic drugs, but their excessive use has the disadvantage of causing drug resistance; therefore, an alternative is the use of herbal medicine for this purpose. Mesquite (Prosopis spp.) has been used in Mexico to treat gastrointestinal diseases attributed to helminths. The present study aimed to characterize the rheological properties of mesquite flour using the SeDeM Expert System to determine its suitability for tablet production by direct compression. Direct compression technology facilitates the tableting process by reducing manufacturing costs. The results of the present study indicate that mesquite flour can be processed by direct compression. The latter could allow the manufacturing of economic tablets to treat infections by H. contortus in ruminants.

Study on Improving the Performance of Traditional Medicine Extracts with High Drug Loading Based on Co-spray Drying Technology

The purpose of this study is to develop modified particles with different structures to improve the flowability and compactibility of Liuwei Dihuang (LWDH) powder using co-spray drying technology, and to investigate the preparation mechanism of modified particles and their modified direct compaction (DC) properties. Moreover, tablets with high drug loading contents were also prepared. Particles were designed using polyvinylpyrrolidone (PVP K30) and hydroxypropyl methylcellulose (HPMC E3) as shell materials, and sodium bicarbonate (NaHCO3) and ammonium bicarbonate (NH4HCO3) as pore-forming agents. The porous particles (Ps), core-shell particles (CPs), and porous core-shell particles (PCPs) were prepared by co-spray drying technology. The key DC properties and texture properties of all the particles were measured and compared. The properties of co-spray drying liquid were also determined and analyzed. According to the results, Ps showed the least improvement in DC properties, followed by CPs, and PCPs showed a significant improvement. The modifier, because of its low surface tension, was wrapped in the outer layer to form a shell, and the pore-forming agent was thermally decomposed to produce pores, forming core-shell, porous, and porous core-shell composite structures. The smooth surface of the shell structure enhances fluidity, while the porous structure allows for greater compaction space, thereby improving DC properties during the compaction process.

Advances in Structure Pharmaceutics from Discovery to Evaluation and Design

Drug delivery systems (DDSs) play an important role in delivering active pharmaceutical ingredients (APIs) to targeted sites with a predesigned release pattern. The chemical and biological properties of APIs and excipients have been extensively studied for their contribution to DDS quality and effectiveness; however, the structural characteristics of DDSs have not been adequately explored. Structure pharmaceutics involves the study of the structure of DDSs, especially the three-dimensional (3D) structures, and its interaction with the physiological and pathological structure of organisms, possibly influencing their release kinetics and targeting abilities. A systematic overview of the structures of a variety of dosage forms, such as tablets, granules, pellets, microspheres, powders, and nanoparticles, is presented. Moreover, the influence of structures on the release and targeting capability of DDSs has also been discussed, especially the in vitro and in vivo release correlation and the structure-based organ- and tumor-targeting capabilities of particles with different structures. Additionally, an in-depth discussion is provided regarding the application of structural strategies in the DDSs design and evaluation. Furthermore, some of the most frequently used characterization techniques in structure pharmaceutics are briefly described along with their potential future applications.

Evaluating the Effect of Microcrystalline Cellulose Variations on Tablet Quality of Natural Plant Product Using a Design of Experiment Approach

Microcrystalline cellulose (MCC) of different grades from different manufacturers differ in particulate and powder properties significantly. The choice of MCC is important to the development of a tablet formulation with satisfactory quality. In this study, the effects of five different MCCs (KG 802, Pharmacel 102, MC 302, M 200, and PH 112) that had different compactibility and tablet disintegration on the tablet quality of two different natural plant products (NPPs) were evaluated systematically, including Crataegi Folium ethanol extract (CF-E) and Sarcandrae Herba water extract (SH-W). The result of D-optimal mixture designs demonstrated that KG 802 showed the best ability to improve compression properties and tensile strength, followed by Pharmacel 102, MC 302, and M 200. PH 112 did the weakest. However, MCCs of different grades had no different influence on the disintegration of NPP tablets. Similar results were found in the experiments of the two different NPP powders, suggesting the generalization of the finding. Moreover, KG 802-containing CF-E formulations showed the largest optimum region size, that is, the lowest production risk. The design space sizes of SH-W were hardly sensitive to the change of MCCs, due to the better tabletability. In conclusion, the properties of MCCs could transfer to the high NPP loading (70%) formulations, leading to the variations on the compression properties and tablet quality. The poorer the tabletability of NPP, the more obvious the variation. The result is promising for the use of MCC and the manufacturing of high drug-loading NPP tablets by direct compression.

Study of Diminutive Granules as Feed Powders for Manufacturability of High Drug Load Minitablets

The maximal amount of drug contained in a minitablet is limited. To reduce the total number of minitablets in a single dose, high drug load minitablets can be prepared from high drug load feed powders by various pharmaceutical processing techniques. Few researchers have however examined the influence of pharmaceutical processing techniques on the properties of high drug load feed powders, and consequently the manufacturability of high drug load minitablets. In this study, silicification of the high drug load physical mix feed powders alone did not yield satisfactory quality attributes and compaction parameters to produce good quality minitablets. The abrasive nature of fumed silica increased ejection force and damage to the compaction tools. Granulation of fine paracetamol powder was crucial for the preparation of good quality high drug load minitablets. The diminutive granules had superior powder packing and flow properties for homogenous and consistent filling of the small die cavities when preparing minitablets. Compared to the physical mix feed powders for direct compression, the granules which possessed higher plasticity, lower rearrangement and elastic energies, yielded better quality minitablets with high tensile strength and rapid disintegration time. High shear granulation demonstrated greater process robustness than fluid bed granulation, with less discernment on the quality attributes of feed powder. It could proceed without fumed silica, with the high shear forces reducing interparticulate cohesivity. An in-depth understanding on the properties of high drug load feed powders with inherently poor compactability and poor flowability is important for the manufacturability of high drug load minitablets.

Texture analysis – a versatile tool for pharmaceutical evaluation of solid oral dosage forms

In the past few decades, texture analysis (TA) has gained importance as a valuable method for the characterization of solid oral dosage forms. As a result, an increasing number of scientific publications describe the textural methods that evaluate the extremely diverse category of solid pharmaceutical products. Within the current work, the use of texture analysis in the characterization of solid oral dosage forms is summarised with a focus on the evaluation of intermediate and finished oral pharmaceutical products. Several texture methods are reviewed regarding the applications in mechanical characterization, and mucoadhesion testing, but also in estimating the disintegration time and in vivo specific features of oral dosage forms. As there are no pharmacopoeial standards for pharmaceutical products tested through texture analysis, and there are important differences between reported results due to different experimental conditions, the choice of testing protocol and parameters is challenging. Thereby, this work aims to guide the research scientists and quality assurance professionals involved in different stages of drug development into the selection of optimal texture methodologies depending on the product characteristics and quality control needs.

Surface Modifiers on Composite Particles for Direct Compaction

Direct compaction (DC) is considered to be the most effective method of tablet production. However, only a small number of the active pharmaceutical ingredients (APIs) can be successfully manufactured into tablets using DC since most APIs lack adequate functional properties to meet DC requirements. The use of suitable modifiers and appropriate co-processing technologies can provide a promising approach for the preparation of composite particles with high functional properties. The purpose of this review is to provide an overview and classification of different modifiers and their multiple combinations that may improve API tableting properties or prepare composite excipients with appropriate co-processed technology, as well as discuss the corresponding modification mechanism. Moreover, it provides solutions for selecting appropriate modifiers and co-processing technologies to prepare composite particles with improved properties.

Improved direct compression properties of Gardeniae Fructus water extract powders via fluid bed-mediated surface engineering

Direct compression (DC) attracts increasing attention for tablet manufacturing; however, its application in medicinal plant tablets is still extremely limited. In this work, eight kinds of the Gardeniae Fructus water extract powder (GF)-based composite particles (CPs) were prepared with different cohesive surface engineering materials, including dextran, inulin, hypromellose, and povidone, alone or in combination with mannitol and colloidal silica. Their physical properties and compacting parameters were characterized comprehensively. All the CPs showed marked improvement in tabletability, which is about 2-4 times higher than that of GF and physical mixtures (PMs). Specifically, the CPs showed a 7.45-26.48 times higher hardness value and a 1.26-2.74 times higher cohesiveness value than PMs. In addition, all the CPs (angle of repose being from 34.27° to 38.46°) showed better flowability than PMs (35.49° to 53.53°) and GF (51.86°). These results demonstrated that (i) fluid-bed coating was not a simple process of superposition and transmission of the physical properties of raw materials; and (ii) all the surface engineering materials studied could improve the DC properties of problematic GF to some degree. As a whole, through the design of fluid-bed coating CPs, qualified tablets with high GF loadings (up to 93%) were produced via DC.

The effect of granules characters on mechanical properties of press-coated tablets: A comparative study

The aim of this study was to investigate the correlation between critical granules characters (including particle size, surface roughness, and apparent porosity) and mechanical properties of press-coated tablets. Granules of a model formulation were prepared through Roll Compaction Granulation (RCG), High Shear Granulation (HSG), and Fluidized Bed Granulation (FBG) to prepare granules with different surface roughness and apparent porosity. The surface roughness and porosity of granules had a significantly greater effect on mechanical properties than the particle size of granules. Whether for brittle or plastic materials, FBG granules with the roughest surface and the greatest apparent porosity exhibited the best compression properties. The elastic recovery test, the interlayer adhesion forces study, the break pattern test, and the X-ray microcomputed tomography investigation suggested that granules with great apparent porosity and rough surfaces could contribute to the production of stable press-coated structures. Moreover, for press-coated tablets prepared using granules, the proper granules in the coat layer could eliminate the side effect of the rigid core on the mechanical strength. The above understandings will be conducive to the selection of compatible and appropriate granules characters, which can enhance mechanical properties and extend the application of press-coated tablets.

Improvements on multiple direct compaction properties of three powders prepared from Puerariae Lobatae Radix using surface and texture modification: comparison of microcrystalline cellulose and two nano-silicas

It has been reported that hydrophilic nano-silica (N) markedly improved direct compaction (DC) properties of Zingiberis Rhizoma alcoholic extract. This study aims to examine the broader scope and generality of the previous work by investigating (i) three powders, i.e., the directly pulverized product, ethanol extract, and water extract prepared from the same medicinal herb-Puerariae Lobatae Radix (named DP, EE, and WE) and (ii) the effects on their DC properties of co-processing with N, hydrophobic nano-silica (BN), or microcrystalline cellulose (C). Unexpectedly, C provided the best improvement on tabletability for WE, while N for both DP and EE. More importantly, only N could move all parent powders to a regime suitable for DC, and BN rather than C enabled parent WE to be directly compressed. Typically, 6/9 N-modified powders simultaneously met the requirements of DC on bulk density, flowability, and tablet tensile strength (σ_t). Principal component analysis indicated that DC properties were mainly governed by flowability and texture properties. The partial least-squares regression model revealed that flowability, texture parameters, and deformation behavior of powders were dominating factors impacting tablet σ_t and solid fraction. Overall, the findings are promising for the manufacture of high drug loading tablets of herbs by DC.

Multifunctional Role of Silica in Pharmaceutical Formulations

Due to the high surface area, adjustable surface and pore structures, and excellent biocompatibility, nano- and micro-sized silica have certainly attracted the attention of many researchers in the medical fields. This review focuses on the multifunctional roles of silica in different pharmaceutical formulations including solid preparations, liquid drugs, and advanced drug delivery systems. For traditional solid preparations, it can improve compactibility and flowability, promote disintegration, adjust hygroscopicity, and prevent excessive adhesion. As for liquid drugs and preparations, like volatile oil, ethers, vitamins, and self-emulsifying drug delivery systems, silica with adjustable pore structures is a good adsorbent for solidification. Also, silica with various particle sizes, surface characteristics, pore structure, and surface modification controlled by different synthesis methods has gained wide attention owing to its unparalleled advantages for drug delivery and disease diagnosis. We also collate the latest pharmaceutical applications of silica sorted out by formulations. Finally, we point out the thorny issues for application and survey future trends pertaining to silica in an effort to provide a comprehensive overview of its future development in the medical fields. Graphical Abstract.