Atomic-scale insight into adsorption of sterically hindered dibenzothiophenes on MoS2 and Co–Mo–S hydrotreating catalysts

Hydrodesulfurization of methanethiol over Co-promoted MoS2 model catalysts

The process of hydrodesulfurization is one of the most important heterogeneous catalytic reactions in industry as it helps with reducing global SOx emissions by selectively removing the sulfur contaminants from commercial fuel. In this work, we successfully combine high-pressure scanning tunneling microscopy and reaction modeling using density functional theory to observe the hydrodesulfurization of methanethiol (CH3SH) on the Co-substituted S edges of a Co-promoted MoS2 model catalyst in situ at near-industrial conditions and investigate the plausible reaction pathways. The active sites on the Co-substituted S edges show a time-varying atomic structure influenced by the hydrodesulfurization reaction rate. The involvement of the edge Co site allows for the C-S bond scission to occur at appreciable rates, and is the critical step in the hydrodesulfurization of CH3SH. The atomic structures of the S-edge active sites from our reaction models match excellently with those observed in situ in the experiments.

Theoretical study of the catalytic hydrodeoxygenation of furan, methylfuran and benzofurane on MoS2

Herein, we have studied the direct deoxygenation (DDO) (without prior hydrogenation) of furan, 2-methylfuran and benzofuran on the metal edge of MoS2 with a vacancy created under pressure of dihydrogen. For the three molecules, we found that the desorption of the water molecule for the regeneration of the vacancy is the most endothermic. Based on the thermodynamic and kinetic aspects, the reactivity order of the oxygenated compounds is furan ≈ 2-methylfuran > benzofuran, which is in agreement with literature. We present the key stages of the mechanisms and highlight the effects of substituents.

Roles of the Comproportionation Reaction in SO2 Reduction Using Methane for the Flexible Recovery of Elemental Sulfur or Sulfides

SO2 reduction with CH4 to produce elemental sulfur (S8) or other sulfides is typically challenging due to high energy barriers and catalyst poisoning by SO2. Herein, we report that a comproportionation reaction (CR) induced by H2S recirculating significantly accelerates the reactions, altering reaction pathways and enabling flexible adjustment of the products from S8 to sulfides. Results show that SO2 can be fully reduced to H2S at a lower temperature of 650 °C, compared to the 800 °C required for the direct reduction (DR), effectively eliminating catalyst poisoning. The kinetic rate constant is significantly improved, with CR at 650 °C exhibiting about 3-fold higher value than DR at 750 °C. Additionally, the apparent activation energy decreases from 128 to 37 kJ/mol with H2S, altering the reaction route. This CR resolves the challenges related to robust sulfur-oxygen bond activation and enhances CH4 dissociation. During the process, the well-dispersed lamellar MoS2 crystallites with Co promoters (CoMoS) act as active species. H2S facilitates the comproportionation reaction, reducing SO2 to a nascent sulfur (Sx*). Subsequently, CH4 efficiently activates CoMoS in the absence of SO2, forming H2S. This shifts the mechanism from Mars-van Krevelen (MvK) in DR to sequential Langmuir-Hinshelwood (L-H) and MvK in CR. Additionally, it mitigates sulfation poisoning through this rapid activation reaction pathway. This unique comproportionation reaction provides a novel strategy for efficient sulfur resource utilization.

Review of Molybdenum Disulfide Research in Slurry Bed Heavy Oil Hydrogenation

With the growing demand for gasoline and diesel fuel and the shortage of conventional oil reserves, there has been extensive interest in upgrading technologies for unconventional feedstocks such as heavy oil. Slurry bed reactors with high tolerance to heavy oil have been extensively investigated. Among them, dispersive MoS₂ is favored for its excellent hydrogenation ability for heavy oil even under harsh reaction conditions such as high pressure and high temperature, its ability to effectively prevent damage to equipment from deposited coke, and its ability to meet the requirement of high catalyst dispersion for slurry bed reactors. This paper reviews the relationship between the structure and hydrogenation effectiveness of dispersive molybdenum disulfide, the hydrogenation mechanism, and the improvement of its hydrogenation performance by adding defects and compares the application of molybdenum disulfide in heavy oil hydrogenation, desulfurization, deoxygenation, and denitrification. It is found that the current research on dispersive molybdenum disulfide catalysts focuses mostly on the reduction of stacking layers and catalytic performance, and there is a lack of research on the lateral dimensions, microdomain regions, and defect sites of MoS₂ catalysts. The relationship between catalyst structure and hydrogenation effect also lags far behind the application of MoS₂ in the precipitation of hydrogen, etc. Oil-soluble and water-soluble MoS₂ catalysts eventually need to be converted to a solid sulfide state to have hydrogenation activity. The conversion history of soluble catalysts to solid-type catalysts and the key to their improved catalytic effectiveness remain unclear.

Metal-Support Interactions in Molecular Single-Site Cluster Catalysts

This study provides atomistic insights into the interface between a single-site catalyst and a transition metal chalcogenide support and reveals that peak catalytic activity occurs when edge/support redox cooperativity is maximized. A molecular platform MCo₆Se₈(PEt₃)₄(L)₂ (1-M, M = Cr, Mn, Fe, Co, Cu, and Zn) was designed in which the active site (M)/support (Co₆Se₈) interactions are interrogated by systematically probing the electronic and structural changes that occur as the identity of the metal varies. All 3d transition metal 1-M clusters display remarkable catalytic activity for coupling tosyl azide and tert-butyl isocyanide, with Mn and Co derivatives showing the fastest turnover in the series. Structural, electronic, and magnetic characterization of the clusters was performed using single crystal X-ray diffraction, ¹H and ³¹P nuclear magnetic resonance spectroscopy, electronic absorption spectroscopy, cyclic voltammetry, and computational methods. Distinct metal/support redox regimes can be accessed in 1-M based on the energy of the edge metal's frontier orbitals with respect to those of the cluster support. As the degree of electronic interaction between the edge and the support increases, a cooperative regime is reached wherein the support can deliver electrons to the catalytic site, increasing the reactivity of key metal-nitrenoid intermediates.

Monolayer CoMoS Catalysts on Hierarchically Porous Alumina Spheres as Bifunctional Nanomaterials for Hydrodesulfurization and Energy Storage Applications

In this work, CoMoS catalysts were synthesized onto porous alumina spheres obtained using Pluronic P-123 (PS) or urea (US) and used as bifunctional nanomaterials for two energy applications: hydrodesulfurization and energy storage. For the first application, the catalysts were assessed in a hydrodesulfurization reactor using two model sulfur molecules, dibenzothiophene and 4,6-dimethyl dibenzothiophene, as well as feeding a heavy oil fraction. The results indicated that the spheres obtained by Pluronic P-123 allowed a greater dispersion degree of MoS2 slabs than US, indicating that the size and hierarchically porous structure of alumina spheres played a principal role as a booster of the HDS catalytic efficiency of DBT, 4,6 DMDBT and diesel fuel. Then, these catalysts were used for the electrocatalysis of the oxygen reduction and oxygen evolution reactions (ORR/OER), which take place in rechargeable Zn-air batteries. For the ORR, the CoMoS catalyst on PS in the presence of a conductive support (N-doped carbon nanotubes + graphene) displayed an overpotential of only 90 mV in comparison with Pt/C. Importantly, the chalcogenide enabled an increase in the stability, maintaining almost two times higher current retention than Pt/C for the ORR and IrO2/C for the OER. These results suggest that expended chalcogenides from the hydrodesulfurization industry can have a second life as co-catalysts for renewable energy storage systems, enabling a circular economy.

Quantitatively Deciphering Electronic Properties of Defects at Atomically Thin Transition-Metal Dichalcogenides

Defects can locally tailor the electronic properties of 2D materials, including the band gap and electron density, and possess the merit for optical and electronic applications. However, it is still a great challenge to realize rational defect engineering, which requires quantitative study of the effect of defects on electronic properties under ambient conditions. In this work, we employed tip-enhanced photoluminescence (TEPL) spectroscopy to obtain the PL spectra of different defects (wrinkle and edge) in mechanically exfoliated thin-layer transition metal dichalcogenides (TMDCs) with nanometer spatial resolution. We quantitatively obtained the band gap and electron density at defects by analyzing the wavelength and intensity ratio of excitons and trions. We further visualized the strain distribution across a wrinkle and the edge-induced reconstructive regions of the band gap and electron density by TEPL line scans. The doping effect on the Fermi level and optical performance was unveiled through comparative studies of edges on TMDC monolayers of different doping types. These quantitative results are vital to guide defect engineering and design and fabrication of TMDC-based optoelectronics devices.

DFT insights into the hydrodenitrogenation mechanism of quinoline catalyzed by different Ni-promoted MoS2 edge sites: Effect of the active phase morphology

Density functional theory calculations are performed to investigate the hydrodenitrogenation (HDN) mechanism of quinoline over different Ni-promoted MoS₂ edges. Based on the calculations, the hydrogenation and ring-opening reaction pathways are explored systematically, and the structure-activity relationship of different active sites is discussed in detail. In the hydrogenation reaction process, the 100% Ni-promoted M-edge and 50% Ni-promoted S-edge are favorable for the formations of 5,6,7,8-tetrahydroquinoline and 1,2,3,4-tetrahydroquinoline, respectively. Furthermore, the 100% Ni-promoted M-edge is more preferable for the generation of decahydroquinoline rather than the 50% Ni-promoted S-edge. In the denitrogenation reaction step, the 100% Ni-promoted M-edge is beneficial for the formation of ortho-propylaniline and 2-propylcyclohexylamine, while 50% Ni-promoted S-edge is only conducive to the formation of 2-propylcyclohexylamine. Therefore, it can be concluded that both hydrogenation derivatives and denitrogenation products exhibit strong dependence on the active phase morphology, meaning that multiple active sites can be involved in one catalytic HDN cycle.

Ni-modified MoS2 nanoflake arrays with stepped sites on carbon nanotubes for efficient hydrodesulfurization of coal-to-liquid fuel

Carbon nanotube (CNT)-supported Ni-modified MoS₂ catalysts with ultra-high loading were synthesized with the assistance of citric acid. The morphology of the nanoflake arrays could be controlled to give abundant stepped sites, which favored the hydrogenation desulfurization pathway of dibenzothiophene. The catalyst exhibited excellent performance and stability for hydrodesulfurization of model oil and coal-to-liquid fuel.

Robust Hot Electron and Multiple Topological Insulator States in PtBi2

A two-dimensional topological insulator features (only) one bulk gap with nontrivial topology, which protects one-dimensional boundary states at the Fermi level. We find a quantum phase of matter beyond this category: a multiple topological insulator. It possesses a ladder of topological gaps; each gap protects a robust edge state. We prove a monolayer of van der Waals material PtBi₂ as a two-dimensional multiple topological insulator. By means of scanning tunneling spectroscopy, we directly visualize the one-dimensional hot electron (and hole) channels with nanometer size on the samples. Furthermore, we confirm the topological protection of these channels by directly demonstrating their robustness to variations of crystal orientation, edge geometry, and sample temperature. The discovered topological hot electron materials may be applied as efficient photocatalysts in the future.

In situ observations of an active MoS2 model hydrodesulfurization catalyst

The hydrodesulfurization process is one of the cornerstones of the chemical industry, removing harmful sulfur from oil to produce clean hydrocarbons. The reaction is catalyzed by the edges of MoS₂ nanoislands and is operated in hydrogen-oil mixtures at 5-160 bar and 260-380 °C. Until now, it has remained unclear how these harsh conditions affect the structure of the catalyst. Using a special-purpose high-pressure scanning tunneling microscope, we provide direct observations of an active MoS₂ model catalyst under reaction conditions. We show that the active edge sites adapt their sulfur, hydrogen, and hydrocarbon coverages depending on the gas environment. By comparing these observations to density functional theory calculations, we propose that the dominant edge structure during the desulfurization of CH₃SH contains a mixture of adsorbed sulfur and CH₃SH.

How Catalysts and Experimental Conditions Determine the Selective Hydroconversion of Furfural and 5-Hydroxymethylfurfural

Furfural and 5-hydroxymethylfurfural stand out as bridges connecting biomass raw materials to the biorefinery industry. Their reductive transformations by hydroconversion are key routes toward a wide variety of chemicals and biofuels, and heterogeneous catalysis plays a central role in these reactions. The catalyst efficiency highly depends on the nature of metals, supports, and additives, on the catalyst preparation procedure, and obviously on reaction conditions to which catalyst and reactants are exposed: solvent, pressure, and temperature. The present review focuses on the roles played by the catalyst at the molecular level in the hydroconversion of furfural and 5-hydroxymethylfurfural in the gas or liquid phases, including catalytic hydrogen transfer routes and electro/photoreduction, into oxygenates or hydrocarbons (e.g., furfuryl alcohol, 2,5-bis(hydroxymethyl)furan, cyclopentanone, 1,5-pentanediol, 2-methylfuran, 2,5-dimethylfuran, furan, furfuryl ethers, etc.). The mechanism of adsorption of the reactant and the mechanism of the reaction of hydroconversion are correlated to the specificities of each active metal, both noble (Pt, Pd, Ru, Au, Rh, and Ir) and non-noble (Ni, Cu, Co, Mo, and Fe), with an emphasis on the role of the support and of additives on catalytic performances (conversion, yield, and stability). The reusability of catalytic systems (deactivation mechanism, protection, and regeneration methods) is also discussed.

Exploring the electron density localization in MoS2 nanoparticles using a localized-electron detector: Unraveling the origin of the one-dimensional metallic sites on MoS2 catalysts

The nature of the electron density localization in two MoS2 nanoclusters containing eight rows of Mo atoms, one with 100% sulphur coverage at the Mo edges (n8_100S) and the other with 50% coverage (n8_50S) was studied using a localized-electron detector function defined in the local moment representation. For n8_100S, pairs of neighboring S2 dimers cover the edges and the electron density localization function analysis shows the presence of a local triangular-shaped ring zone of highly delocalized electrons along these edges, which corresponds to a good metallic conductor zone. The optimized geometry analysis shows that the Mo-S2 bond length is much longer than that of the Mo-S bonds inside the cluster. The removal of one S atom from each sulphur dimer to create a cluster with 50% coverage produces a general compressive stress on the cluster optimized geometry, which shortens the Mo-S bond length, particularly at the edge. The electron density location function analysis shows that close to the cluster corners, a zone of highly delocalized electron zones with a characteristic semiconductor pattern and broken one-dimensional metallic ring was generated. These results suggest that the Mo-S2 bond elongation produced by the sulphur dimers is similar to a MoS2 monolayer under tensile strain and is the origin of the one-dimensional metallic sites at the Mo-edges. In general, the present findings show excellent agreement with the key features of the reported ambient pressure X-ray photoemission spectra and the corresponding simulated scanning tunneling microscopy images.

Topotactic Growth of Edge-Terminated MoS2 from MoO2 Nanocrystals

Layered transition metal dichalcogenides have distinct physicochemical properties at their edge-terminations. The production of an abundant density of edge structures is, however, impeded by the excess surface energy of edges compared to basal planes and would benefit from insight into the atomic growth mechanisms. Here, we show that edge-terminated MoS₂ nanostructures can form during sulfidation of MoO₂ nanocrystals by using in situ transmission electron microscopy (TEM). Time-resolved TEM image series reveal that the MoO₂ surface can sulfide by inward progression of MoO₂(202̅):MoS₂(002) interfaces, resulting in upright-oriented and edge-exposing MoS₂ sheets. This topotactic growth is rationalized in the interplay with density functional theory calculations by successive O-S exchange and Mo sublattice restructuring steps. The analysis shows that formation of edge-terminated MoS₂ is energetically favorable at MoO₂(110) surfaces and provides a necessary requirement for the propensity of a specific MoO₂ surface termination to form edge-terminated MoS₂. Thus, the present findings should benefit the rational development of transition metal dichalcogenide nanomaterials with abundant edge terminations.

Molecular recognition with cyclodextrin polymer: a novel method for removing sulfides efficiently

A series of cyclodextrin polymers (CDPs) were synthesized and they were used for removing different sulfides by molecular recognition. It's showed that β-CDP has a more suitable cavity size for removing DBT.

Temperature sensitive synthesis of γ-Al2O3support with different morphologies for CoMo/γ-Al2O3catalysts for hydrodesulfurization of thiophene and 4,6-dimethyldibenzothiophene

Two different kinds of γ-Al₂O₃precursors: stick-like ammonium aluminum carbonate hydroxide and willow leaf-like boehmite could be selectively synthesizedviaa facile hydrothermal method by just adjusting reaction temperature.

Synthesis of a Co–Mo sulfide catalyst with a hollow structure for highly efficient hydrodesulfurization of dibenzothiophene

Co–Mo sulfides with tube-like structures exhibit super high activity for HDS of DBT.