TiO2 crystal facet-dependent antimony adsorption and photocatalytic oxidation

Facile synthesis of Bi3O(OH)(AsO4)2 and simultaneous photocatalytic oxidation and adsorption of Sb(III) from wastewater

Antimony (Sb) decontamination in water is necessary owing to the worsening pollution which seriously threatens human life safety. Designing bismuth-based photocatalysts with hydroxyls have attracted growing interest because of the broad bandgap and enhanced separation efficiency of photogenerated electron/hole pairs. Until now, the available photocatalysis information regarding bismuth-based photocatalysts with hydroxyls has remained scarce and the contemporary report has been largely limited to Bi3O(OH)(PO4)2 (BOHP). Herein, Bi3O(OH)(AsO4)2 (BOHAs), a novel ultraviolet photocatalyst, was fabricated via the co-precipitation method for the first time, and developed to simultaneous photocatalytic oxidation and adsorption of Sb(III). The rate constant of Sb(III) removal by the BOHAs was 32.4, 3.0, and 4.3 times higher than those of BiAsO4, BOHP, and TiO2, respectively, indicating that the introduction of hydroxyls could increase the removal of Sb(III). Additionally, the crucial operational parameters affecting the adsorption performance (catalyst dosage, concentration, pH, and common anions) were investigated. The BOHAs maintained 85% antimony decontamination of the initial yield after five successive cycles of photocatalysis. The Sb(III) removal involved photocatalytic oxidation of adsorbed Sb(III) and subsequent adsorption of the yielded Sb(V). With the acquired knowledge, we successfully applied the photocatalyst for antimony removal from industrial wastewater. In addition, BOHAs could also be powerful photocatalysts in the photodegradation of organic pollutants studies of which are ongoing. It reveals an effective strategy for synthesizing bismuth-based photocatalysts with hydroxyls and enhancing pollutants' decontamination.

A critical review on adsorptive removal of antimony from waters: Adsorbent species, interface behavior and interaction mechanism

Antimony (Sb) has raised widespread concern because of its negative effects on ecology and human health. The extensive use of antimony-containing products and corresponding Sb mining activities have discharged considerable amounts of anthropogenic Sb into the environment, especially the water environment. Adsorption has been employed as the most effective strategy for Sb sequestration from water; thus, a comprehensive understanding of the adsorption performance, behavior and mechanisms of adsorbents benefits to develop the optimal adsorbent to remove Sb and even drive its practical application. This review presents a holistic analysis of adsorbent species with the ability to remove Sb from water, with a special emphasis on the Sb adsorption behavior of various adsorption materials and their Sb-adsorbent interaction mechanisms. Herein, we summarize research results based on the characteristic properties and Sb affinities of reported adsorbents. Various interactions, including electrostatic interactions, ion exchange, complexation and redox reactions, are fully reviewed. Relevant environmental factors and adsorption models are also discussed to clarify the relevant adsorption processes. Overall, iron-based adsorbents and corresponding composite adsorbents show relatively excellent Sb adsorption performance and have received widespread attention. Sb removal mainly depends on chemical properties of the adsorbent and Sb itself, and complexation is the main driving force for Sb removal, assisted by electrostatic attraction. The future directions of Sb removal by adsorption focus on the shortcomings of current adsorbents; more attention should be given to the practicability of adsorbents and their disposal after use. This review contributes to the development of effective adsorbents for removing Sb and provides an understanding of Sb interfacial processes during Sb transport and the fate of Sb in the water environment.

Construction of an S-scheme TiOF2/HTiOF3 heterostructures with abundant OVs and OH groups: Performance, kinetics and mechanism insight

Developing efficient photocatalysts is of crucial significance for the development of photocatalysis techniques. In this work, an S-scheme alkaline-washed TiOF₂/HTiOF₃(OHTOF) heterostructures with abundant Oxygen vacancies (Ovs) and OH groups was successfully constructed and used to remedy antibiotic wastewater under simulated sunlight. The generation of HTiOF₃ was induced by g-C₃N₄ regulation. The results displayed that OHTOF15 composite possessed the best photocatalytic performance, which could degrade 94.2% tetracyclinehydrochloride (TCH) at a rate speed constant of 1.077 min^-1 in 2.5 h. The after-alkali-washing process increased the concentration of OH groups and Ovs defects, and greatly enlarged the surface area. The abundant Ovs and OH groups were conducive to the formation of free radicals' and the transport of charge carriers. Compared with the pristine TiOF₂, the absorption sidebands of OHTOF series were greatly red-shifted, which indicated that the increase of OH groups and the etching of the morphology of OHTOF further enhanced its visible-light harvesting ability. Furthermore, the metal cycle of the variable state of Ti⁴⁺/Ti³⁺ in OHTOF15 compensated for the charge balance and promoted the efficient separation of the carriers. Additionally, the apparent quantum efficiency (AQE) of the TCH photodegradation system based on Chemical Oxygen Demand (COD) removal efficiency was calculated to be 0.32%. It was confirmed that the electron transport path in TiOF₂/HTiOF₃ nanocomposites system followed the S-scheme type, which increased the charge carriers' separation rate and maintained a strong redox capacity. This work could provide some enlightenment for the construction of the semiconducting heterojunction and controllable surface defects engineering.

Insights into Chlorobenzene Catalytic Oxidation over Noble Metal Loading {001}-TiO2: The Role of NaBH4 and Subnanometer Ru Undergoing Stable Ru0Ru4+ Circulation

Catalytic combustion of ubiquitous chlorinated volatile organic compounds (CVOCs) encounters bottlenecks regarding catalyst deactivation by chlorine poisoning and generation of toxic polychlorinated byproducts. Herein, Ru, Pd, and Rh were loaded on {001}-TiO₂ for thermal catalytic oxidation of chlorobenzene (CB), with Ru/{001}-TiO₂ representing superior reactivity, CO₂ selectivity, and stability in the 1000 min on-stream test. Interestingly, both acid sites and reactive active oxygen species (ROS) were remarkably promoted via adding NaBH₄. But merely enhancing these active sites of the catalyst in CVOC treatment is insufficient. Continuous deep oxidation of CB with effective Cl desorption is also a core issue successfully tackled through the steady Ru⁰↔Ru⁴⁺ circulation. This circulation was facilitated by the observed higher subnanometer Ru dispersion on {001}-TiO₂ than the other two noble metals that was supported by single atom stability DFT calculation. Nearly 88 degradation products in off-gas were detected, with Ru/{001}-TiO₂ producing the lowest polychlorinated benzene byproducts. An effective and sustainable CB degradation mechanism boosted by the cooperation of NaBH₄ enhanced active sites and Ru circulation was proposed accordingly. Insights gained from this study open a new avenue to the rational design of promising catalysts for the treatment of CVOCs.

Electrocatalytic Removal of Low-Concentration Uranium Using TiO2 Nanotube Arrays/Ti Mesh Electrodes

Groundwater containing naturally occurring uranium is a conventional drinking water source in many countries. Removal of low concentrations of uranium complexes in groundwater is a challenging task. Here, we demonstrated that the TiO₂ nanotube arrays/Ti (TNTAs/Ti) mesh electrode could break through the concentration limit and efficiently remove low concentrations of uranium complexes from both simulated and real groundwater. U(VI) complexes in groundwater were electro-reduced to UO₂ and deposited on the TNTAs/Ti mesh electrode surface. The adsorption rate and electron transfer rate of the anatase TNTAs/Ti mesh electrode were twice that of the rutile TNTAs/Ti mesh electrode. Therefore, the anatase TNTAs/Ti mesh electrode exhibited excellent electrocatalytic activity toward the electrochemical removal of U(VI), which could work at a higher potential and significantly reduce the energy consumption of U(VI) removal. The U(VI) adsorption capacity on the anatase TNTAs/Ti mesh electrode was limited due to the low U(VI) concentration. However, the anatase TNTAs/Ti mesh electrode displayed a huge U(VI) removal capacity using the electroreduction method, where adsorption and reduction of U(VI) were mutually promoted and induced continuous accumulation of UO₂ on the electrode. The accumulated UO₂ can be easily recovered in dilute HNO₃, and the electrode can be used repeatedly.

Photocatalysis for arsenic removal from water: considerations for solar photocatalytic reactors

The following work provides a perspective on the potential application of solar heterogeneous photocatalysis, which is a nonselective advanced oxidation process considered as a sustainable technology, to assist in arsenic removal from water, which is a global threat to human health. Heterogeneous photocatalysis can oxidize trivalent arsenic to pentavalent arsenic, decreasing its toxicity and easing its removal with other technologies, such as chemical precipitation and adsorption. Several lab-scale arsenic photocatalytic oxidation and diverse solar heterogeneous photocatalytic operations carried out in different reactor designs are analyzed. It was found out that this technology has not been translated to operational pilot plant scale prototypes. General research on reactors is scarce, comprising a small percentage of the photocatalysis related scientific literature. It was possible to elucidate some operational parameters that a reactor must comply to operate efficiently. Reports on small-scale application shed light that in areas where other water purification technologies are economically and/or technically not suitable, and the solar energy is available, shed light on the fact that solar heterogeneous photocatalysis is highly promissory within a water purification process for removal of arsenic from water.

Insights into adsorptive removal of antimony contaminants: Functional materials, evaluation and prospective

The application of antimony containing compounds in the industry has generated considerable antimony contaminants, which requires to develop methods that are as efficient as possible to remove antimony from water in the view of human health. The adsorption is among the most high-efficiency and reliable purification methods for hazardous materials due to the simple operation, convenient recycling and low cost. Herein, this review systematically summarizes the functional materials that are used to adsorb antimony from water, including metal (oxides) based materials, carbon-based materials, MOFs and molecular sieves, layered double hydroxides, natural materials, and organic-inorganic hybrids. The iron-based adsorbents stand out among these adsorbents because of their excellent performance. Moreover, the interaction between antimony and different functional materials is discussed in detail, while the inner-sphere complexation, hydrogen bond as well as ligand exchange are the main impetus during antimony adsorption. In addition, the desorption methods in adsorbents recycling are also comprehensively summarized. Furthermore, we propose an adsorption capacity balanced evaluation function (ABEF) based on the reported results to evaluate the performance of the antimony adsorption materials for both Sb(III) and Sb(V), as antimony usually has two valence forms of Sb(III) and Sb(V) in wastewater. Another original insight in this review is that we put forward a potential application prospect for the antimony-containing waste adsorbents. The feasible future development includes the utilization of the recycled antimony-containing waste adsorbents in catalysis and energy storage, and this will provide a green and sustainable pathway for both antimony removal and resourization.

Antimonate removal by diatomite modified with Fe-Mn oxides: application and mechanism study

In this study, diatomite coated with Fe-Mn oxides (DFMO) was synthesized through calcination. The adsorption of antimonate (Sb(V)) by DFMO was studied, and environmental factors affecting the adsorption were investigated. The components of DFMO were identified as γ-Fe₂O₃, γ-MnO₂, and SiO₂, in the presence of diatomite covered with nanoscale metal oxides. Batch experiments were carried out to evaluate the antimonate adsorption performance in aqueous solution. Results showed that maximum Sb(V) adsorption capacity of DFMO reached 10.7 mg/g at pH 4, corresponding to 22.2 mg/g per unit metal oxides. Antimonate adsorption occurred on heterogenous surface, following the Freundlich and Pseudo-second order model. Overall, antimonate adsorption was favored at acidic condition due to low point of zero charge. However, when treating electroplating wastewater, neutral pH condition exhibited a higher efficiency than acidic pH, because co-existing ions in electroplating wastewater significantly affects antimony adsorption. Further investigation showed that among different potential co-existing ions, fluoride can strongly inhibit the adsorption of antimonate at 5 mg/L under pH 4. Density functional theory (DFT) analysis confirmed that adsorption energy on DFMO follows: HF < F^- < Sb(OH)₆^-, indicating that fluoride is easier to bind with DFMO compared to antimonate, especially under pH 3.5 at which fluoride exists as HF. Moreover, the competitive adsorption of fluoride toward antimonate indicated the necessity of pre-treatment like neutralization and precipitation before adsorption process.

Toward Informed Design of Nanomaterials: A Mechanistic Analysis of Structure-Property-Function Relationships for Faceted Nanoscale Metal Oxides

Nanoscale metal oxides (NMOs) have found wide-scale applicability in a variety of environmental fields, particularly catalysis, gas sensing, and sorption. Facet engineering, or controlled exposure of a particular crystal plane, has been established as an advantageous approach to enabling enhanced functionality of NMOs. However, the underlying mechanisms that give rise to this improved performance are often not systematically examined, leading to an insufficient understanding of NMO facet reactivity. This critical review details the unique electronic and structural characteristics of commonly studied NMO facets and further correlates these characteristics to the principal mechanisms that govern performance in various catalytic, gas sensing, and contaminant removal applications. General trends of facet-dependent behavior are established for each of the NMO compositions, and selected case studies for extensions of facet-dependent behavior, such as mixed metals, mixed-metal oxides, and mixed facets, are discussed. Key conclusions about facet reactivity, confounding variables that tend to obfuscate them, and opportunities to deepen structure-property-function understanding are detailed to encourage rational, informed design of NMOs for the intended application.

Removal of aqueous As(III) Sb(III) by potassium ferrate (K2FeO4): The function of oxidation and flocculation

This study investigated the effects of potassium ferrate (K₂FeO₄) dosage, pH, and reaction time on the removal of aqueous As(III) and Sb(III), and revealed the oxidation and flocculation mechanism of K₂FeO₄. The results show that the removal efficiencies of As(III) and Sb(III) were highly related to the hydrolysate of K₂FeO₄ under acidic conditions, while the efficiencies were low under alkaline condition, owning to the electrostatic repulsion between iron nanoparticles and charged As/Sb species. The increased dosage and reaction time improved the adsorption performance. Based on the comparative experiments with FeCl₃, the simultaneous removal of As(III) and Sb(III) by K₂FeO₄ suggested that As(III) was eliminated due to the processes of oxidation, flocculation, and chemical precipitation, while Sb(III) was removed mostly by oxidation and flocculation. The generated precipitates were characterized with surface analysis and the results support that the oxidization property of K₂FeO₄ was essential during the removal of As(III) and Sb(III), and removal mechanisms between both elements were different.

Simultaneous oxidation and sorption of highly toxic Sb(III) using a dual-functional electroactive filter

One of the topics gaining lots of recent attention is the antimony (Sb) pollution. We have designed a dual-functional electroactive filter consisting of one-dimensional (1-D) titanate nanowires and carbon nanotubes for simultaneous oxidation and sorption of Sb(III). Applying an external limited DC voltage assist the in-situ conversion of highly toxic Sb(III) to less toxic Sb(V). The Sb(III) removal kinetics and efficiency were enhanced with flow rate and applied voltage (e.g., the Sb(III) removal efficiency increased from 87.5% at 0 V to 96.2% at 2 V). This enhancement in kinetics and efficiency are originated from the flow-through design, more exposed sorption sites, electrochemical reactivity, and limited pore size on the filter. The titanate-CNT hybrid filters perform effectively across a wide pH range of 3-11. Only negligible inhibition was observed in the presence of nitrate, chloride, and carbonate at varying concentrations. Our analyses using STEM, XPS, or AFS demonstrate that Sb were mainly adsorbed by Ti. DFT calculations suggest that the Sb(III) oxidation kinetics can be accelerated by the applied electric field. Exhausted titanate-CNT filters can be effectively regenerated by using NaOH solution. Moreover, the Sb(III)-spiked tap water generated ∼2400 bed volumes with a >90% removal efficiency. This study provides new insights for rational design of continuous-flow filters for the decontamination of Sb and other similar heavy metal ions.

Electroactive Modified Carbon Nanotube Filter for Simultaneous Detoxification and Sequestration of Sb(III)

Herein, we rationally designed a dual-functional electroactive filter system for simultaneous detoxification and sequestration of Sb(III). Binder-free and nanoscale TiO₂-modified carbon nanotube (CNT) filters were fabricated. Upon application of an external electrical field, in situ transformation of Sb(III) to less toxic Sb(V) can be achieved, which is further sequestered by TiO₂. Sb(III) removal kinetics and capacity increase with applied voltage and flow rate. This can be explained by the synergistic effects of the filter's flow-through design, electrochemical reactivity, small pore size, and increased number of exposed sorption sites. STEM characterization confirms that Sb were mainly sequestered by TiO₂. XPS, AFS, and XAFS results verify that the Sb(III) conversion process was accelerated by the electrical field. The proposed electroactive filter technology works effectively across a wide pH range. The presence of sulfate, chloride, and carbonate ions negligibly inhibited Sb(III) removal. Exhausted TiO₂-CNT filters can be effectively regenerated using NaOH solution. At 2 V, 100 μg/L Sb(III)-spiked tap water generated ∼1600 bed volumes of effluent with >90% efficiency. Density functional theory calculations suggest that the adsorption energy of Sb(III) onto TiO₂ increases (from -3.81 eV to -4.18 eV) and Sb(III) becomes more positively charged upon application of an electrical field.

Antimony speciation in the environment: Recent advances in understanding the biogeochemical processes and ecological effects

Antimony (Sb) is a toxic metalloid, and its pollution has become a global environmental problem as a result of its extensive use and corresponding Sb-mining activities. The toxicity and mobility of Sb strongly depend on its chemical speciation. In this review, we summarize the current knowledge on the biogeochemical processes (including emission, distribution, speciation, redox, metabolism and toxicity) that trigger the mobilization and transformation of Sb from pollution sources to the surrounding environment. Natural phenomena such as weathering, biological activity and volcanic activity, together with anthropogenic inputs, are responsible for the emission of Sb into the environment. Sb emitted in the environment can adsorb and undergo redox reactions on organic or inorganic environmental media, thus changing its existing form and exerting toxic effects on the ecosystem. This review is based on a careful and systematic collection of the latest papers during 2010-2017 and our research results, and it illustrates the fate and ecological effects of Sb in the environment.

Molecular-Level Understanding of Selectively Photocatalytic Degradation of Ammonia via Copper Ferrite/N-Doped Graphene Catalyst under Visible Near-Infrared Irradiation

Developing photocatalysts with molecular recognition function is very interesting and desired for specific applications in the environmental field. Copper ferrite/N-doped graphene (CuFe2O4/NG) hybrid catalyst was synthesized and characterized by surface photovoltage spectroscopy, X-ray powder diffraction, transmission electron microscopy, Raman spectroscopy, UV–Vis near-infrared diffuse reflectance spectroscopy and X-ray photoelectron spectroscopy. The CuFe2O4/NG catalyst can recognize ammonia from rhodamine B (RhB) in ammonia-RhB mixed solution and selectively degrade ammonia under visible near-infrared irradiation. The degradation ratio for ammonia reached 92.6% at 6 h while the degradation ratio for RhB was only 39.3% in a mixed solution containing 100.0 mg/L NH3-N and 50 mg/L RhB. Raman spectra and X-ray photoelectron spectra indicated ammonia adsorbed on CuFe2O4 while RhB was adsorbed on NG. The products of oxidized ammonia were detected by gas chromatography, and results showed that N2 was formed during photocatalytic oxidization. Mechanism studies showed that photo-generated electrons flow to N-doped graphene following the Z-scheme configuration to reduce O2 dissolved in solution, while photo-generated holes oxidize directly ammonia to nitrogen gas.

Effect of organic matter on mobilization of antimony from nanocrystalline titanium dioxide

Antimony (Sb) is of increasing environmental concern worldwide. The sorption behavior of Sb was investigated. Both Sb(III) and Sb(V) were likely to be sorbed onto nanocrystalline titanium dioxide (TiO₂). Sorption studies showed that the Sb(V) sorption capacity and rate for TiO₂ were greater than those of Sb(III). The highest Sb(III) and Sb(V) sorption on TiO₂, on the basis of the Langmuir equation, were 333 and 588 mmol kg^-1, respectively. The study suggested that TiO₂ is an effective adsorbent for Sb removal. In addition, Sb mobilization in the presence of humic acid (HA) was found to be highly pH-dependent. For pH values of 9-11, the addition of HA enhanced Sb mobilization significantly. The results highlight the importance of organic matter in the mobilization of Sb in alkaline-contaminated environments.