One-pot synthesis of magnetic iron oxide nanoparticle-multiwalled carbon nanotube composites for enhanced removal of Cr(VI) from aqueous solution

Fe doping enhanced Cr(VI) adsorption efficiency of cerium-based adsorbents: Adsorption behaviors and inner removal mechanisms

Cerium-based adsorbents possessed unique advantages of valence variability and abundant oxygen vacancies in hexavalent chromium (Cr(VI)) adsorption, but high cost and unstable properties restricted their application in Cr(VI) contained wastewater treatment. Herein, a series of bimetallic adsorbents with different cerium/iron ratios (CeFe@C) were prepared by adding inexpensive Fe into Ce-based adsorbents (Ce@C), and the effect of Fe doping on adsorption properties of Ce@C for Cr(VI) was investigated thoroughly. Compared with pristine Ce@C, CeFe@C exhibited excellent removal performance for Cr(VI), and the improved maximum adsorption capacity reached 75.11 mg/g at 25℃. Benefiting from Fe doping, CeFe@C had good regeneration property, with only 25 % decrease after five adsorption-desorption cycles. Contents of trivalent cerium (Ce(III)) and oxygen vacancies (Ov) in bimetallic adsorbents were positively correlated with divalent iron (Fe(II)) doping, indicating that the formation of Ce(III) and surface defects on Ce@C could be effectively regulated by Fe doping. Density functional theory (DFT) calculation results further proved that the doped Fe enhanced the electron transfer effectively and lowered the energy barriers of Cr(VI) adsorption onto Ce@C surface, strengthening the reduction and complexation to Cr(VI). This study provides new insights for improving the Cr(VI) removal performance by modified Ce-based adsorbents, and further promotes the utilization potentiality of low-cost and low-toxicity Ce-based adsorbents in Cr(VI)-containing wastewater treatment.

Effective chromium removal of metal anchored alginate-chitosan binary bio-composites

Water is the most essential resource for the biotic and abiotic components of an ecosystem. Any change in the quality of this water may cause adverse impact on the ecosystem. Hexavalent chromium is one such important pollutant that gets exposed in the water mainly through anthropogenic processes. Adsorption is considered to be an effective, economic and easiest method for remediation of such pollutants. Amongst the innumerable adsorbents available, biopolymers fetch the interest due to its cost effectiveness, efficiency and biocompatibility. But, the mechanical strength and workability of such biopolymers makes it unfit to use as an adsorbent. To improve these drawbacks, synthesis of biopolymeric composites become the need of the hour. So, an attempt was made here to synthesize metal cross-linked binary bio-composites using Alginate and Chitosan polymer matrix. Synthesized bio-composites were characterised with the aid of FTIR, XPS, Thermal analysis, SEM with EDAX and subjected for hexavalent chromium removal from water. Analysis of variance (ANOVA) with 95 % confidence intervals was used to assess the significance of independent variables and their interactions. Adsorption studies were done using batch process and to achieve greater sorption, various influencing parameters were optimized one by one. While investigating one parameter, other parameters were kept unaltered. Optimization was done for the parameters like contact time, dosage of the adsorbent, pH of the medium and presence of co-ions. Contact time and dosage for all the composites was 30 mins and 0.1 g respectively. Amongst the composites, Zirconium loaded binary composite possess high sorption capacity of around 14.8 mg/g. While Calcium and Iron loaded composites exhibit sorption capacity of around 9.8 mg/g and 10.4 mg/g respectively. Presence of other co-ions in the medium doesn't affect the sorption process. Isothermal studies infer the adsorption follows Langmuir model and thermodynamic parameters concludes the endothermic and randomness of the adsorption. The bio-composites can be recycled and used upto three cycles. Field trial was conducted and the composites work well in such conditions.

Design, Synthesis, and Evaluation of Novel Magnetic Nanoparticles Combined with Thiophene Derivatives for the Removal of Cr(VI) from an Aqueous Solution

Most heavy metals are harmful to human health and the environment, even at extremely low concentrations. In natural waters, they are usually found only in trace amounts. Researchers are paying great attention to nanotechnology and nanomaterials as viable solutions to the problem of water pollution. This research focuses on the synthesis of organic thiophene derivatives that can be used as grafted ligands on the surface of silica-coated iron oxide nanoparticles to remove Cr(VI) chromium ions from water. The Vilsmeier-Haack reaction allows the formation of aldehyde groups in thiophene derivatives, and the resulting products were characterized by the FT-IR, NMR, and GC-MS. Schiff base is used as a binder between organic compounds and nanoparticles by the reaction of aldehyde groups in thiophene derivatives and amine groups on the surface of coated iron oxide nanoparticles. Schiff base functionalized Fe3O4 composites (MNPs@SiO2-SB-THCA) and (MNPs@SiO2-SB-THCTA) were successfully synthesized by homogeneous and heterogeneous methods and characterized by a combination of FT-IR, transmission electron microscopy, X-ray photoelectron spectroscopy, and thermogravimetric analysis. The adsorption studies, kinetic modeling, adsorption isotherms, and thermodynamics of the two materials, MNPs@SiO2-SB-THCA and MNPs@SiO2-SB-THCTA, were investigated for the removal of Cr(VI) from water at room temperature and at 50 mg/L. The high adsorption capacity at pH 6 for MNPs@SiO2-SB-THCTA was 15.53 mg/g, and for MNPs@SiO2-SB-THCA, it was 14.31 mg/g.

Highly efficient Cr (VI) removal from electroplating wastewater by regenerable copper sulfides: Mechanism and magical induction effect for Cr resource recovery

The current sorbents used to remove Cr (VI) from electroplating wastewater are faced with some challenges including the difficulty in separating, regenerating, and safely disposing of adsorbed Cr species. To address these challenges, CuSx/TiO2 was developed to recover Cr (VI) from electroplating wastewater. CuSx/TiO2 had superior performance in removing Cr (VI), with the rate and capacity of approximately 9.36 mg g-1 h-1 and 68.8 mg g-1 at initial pH 4.0, respectively. Additionally, Cu2+ released from CuSx/TiO2 during Cr (VI) removal would come back to its external surface as the Cu(OH)2 precipitate at initial pH 4.0, which helped to prevent the generation of secondary pollution. The Cu(OH)2 precipitate would be decomposed into CuOx after calcination, which would then be transformed back into CuSx by re-sulfuration for regeneration. Hence, CuSx showed a magical induction effect on Cr (VI) recovery, and Cr (VI) from electroplating wastewater might be gradually enriched as Cr2O3 in the sandwich between CuSx and TiO2 through multiple regenerations and removals, which could be considered as a chromium ore resource for industrial applications when the amount of enriched Cr2O3 reached more than 30 wt%. Overall, CuSx/TiO2 showed great potential as a promising sorbent for Cr (VI) removal from electroplating wastewater.

A review on adsorption of heavy metals from wastewater using carbon nanotube and graphene-based nanomaterials

The rampant rise in world population, industrialization, and urbanization expedite the contamination of water sources. The presence of the non-biodegradable character of heavy metals in waterways badly affects the ecological balance. In this modern era, the unavailability of getting clear water as well as the downturn in water quality is a major concern. Therefore, the effective removal of heavy metals has become much more important than before. In recent years, the attention to better wastewater remediation was directed towards adsorption techniques with novel adsorbents such as carbon nanomaterials. This review paper primarily emphasizes the fundamental concepts, structures, and unique surface properties of novel adsorbents, the harmful effects of various heavy metals, and the adsorption mechanism. This review will give an insight into the current status of research in the realm of sustainable wastewater treatment, applications of carbon nanomaterials, different types of functionalized carbon nanotubes, graphene, graphene oxide, and their adsorption capacity. The importance of MD simulations and density functional theory (DFT) in the elimination of heavy metals from aqueous media is also discussed. In addition to that, the effect of factors on heavy metal adsorption such as electric field and pressure is addressed.

The role of cGAS-STING signaling in pulmonary fibrosis and its therapeutic potential

Pulmonary fibrosis is a progressive and ultimately fatal lung disease, exhibiting the excessive production of extracellular matrix and aberrant activation of fibroblast. While Pirfenidone and Nintedanib are FDA-approved drugs that can slow down the progression of pulmonary fibrosis, they are unable to reverse the disease. Therefore, there is an urgent demand to develop more efficient therapeutic approaches for pulmonary fibrosis. The intracellular DNA sensor called cyclic guanosine monophosphate-adenosine monophosphate (cGAMP) synthase (cGAS) plays a crucial role in detecting DNA and generating cGAMP, a second messenger. Subsequently, cGAMP triggers the activation of stimulator of interferon genes (STING), initiating a signaling cascade that leads to the stimulation of type I interferons and other signaling molecules involved in immune responses. Recent studies have highlighted the involvement of aberrant activation of cGAS-STING contributes to fibrotic lung diseases. This review aims to provide a comprehensive summary of the current knowledge regarding the role of cGAS-STING pathway in pulmonary fibrosis. Moreover, we discuss the potential therapeutic implications of targeting the cGAS-STING pathway, including the utilization of inhibitors of cGAS and STING.

Enhancing chromium removal and recovery from industrial wastewater using sustainable and efficient nanomaterial: A review

Water contamination can be detrimental to the human health due to higher concentration of carcinogenic heavy metals such as chromium (Cr) in the wastewater. Many traditional methods are being employed in wastewater treatment plants for Cr removal to control the environmental impacts. Such methods include ion exchange, coagulation, membrane filtration, and chemical precipitation and microbial degradation. Recent advances in materials science and green chemistry have led to the development of nanomaterial that possess high specific surface areas and multiple functions, making them suitable for removing metals such as Cr from wastewater. Literature shows that the most efficient, effective, clean, and long-lasting approach for removing heavy metals from wastewater involves adsorbing heavy metals onto the surface of nanomaterial. This review assesses the removal methods of Cr from wastewater, advantages and disadvantages of using nanomaterial to remove Cr from wastewater and potential negative impacts on human health. The latest trends and developments in Cr removal strategies using nanomaterial adsorption are also explored in the present review.

Gentamicin Sulfate Grafted Magnetic GO Nanohybrids with Excellent Antibacterial Properties and Recyclability

In this study, magnetic graphene oxide (MGO) nanohybrids were first prepared by loading Fe₃O₄ NPs onto graphene oxide (GO). Then, GS-MGO nanohybrids were prepared by grafting gentamicin sulfate (GS) onto MGO directly using a simple amidation reaction. The prepared GS-MGO had the same magnetism as MGO. They exhibited excellent antibacterial ability against Gram-negative bacteria and Gram-positive bacteria. The GS-MGO had excellent antibacterial performance against Escherichia coli (E. coli), Staphylococcus aureus (S. aureus), and Listeria monocytogenes (L. monocytogenes). When the addition concentration of GS-MGO was 1.25 mg/mL, the calculated bacteriostatic ratios against E. coli and S. aureus achieved 89.8% and 100%, respectively. For L. monocytogenes, only 0.05 mg/mL of GS-MGO had an antibacterial ratio as high as 99%. In addition, the prepared GS-MGO nanohybrids also exhibited excellent non-leaching activity with good recycling antibacterial ability. After eight times antibacterial tests, GS-MGO nanohybrids still exhibited an excellent inhibition effect on E. coli, S. aureus, and L. monocytogenes. Therefore, as a non-leaching antibacterial agent, the fabricated GS-MGO nanohybrid had dramatic antibacterial properties and also showed great recycling ability. Thus, it displayed great potential in the design of novel recycling antibacterial agents with non-leaching activity.

Construction of efficient Ni-FeLDH@MWCNT@Cellulose acetate floatable microbeads for Cr(VI) removal: Performance and mechanism

Water pollution is an aggravating dilemma that is extending around the world, threatening human survival. Strikingly, the notorious heavy metals like hexavalent chromium ions (Cr⁶⁺) cause environmental problems raising awareness of the essentials for finding feasible solutions. For this purpose, the self-floating Ni-FeLDH@MWCNT@CA microbeads were prepared for removing Cr⁶⁺. The morphological, thermal, and composition characteristics of Ni-FeLDH@MWCNT@CA microbeads were analyzed using XRD, FTIR, TGA, SEM, XPS, and zeta potential. Notably, the adsorption aptitude of Cr⁶⁺ was enhanced by raising the MWCNTs proportion to 5 wt% in microbeads. The Cr⁶⁺ adsorption onto Ni-FeLDH@MWCNT@CA fitted Langmuir and Freundlich isotherm models with q_m of 384.62 mg/g at pH 3 and 298 K. The adsorption process was described kinetically by the pseudo-2nd order model. More importantly, the adsorption of Cr⁶⁺ onto Ni-FeLDH@MWCNT@CA occurred via electrostatic interactions, inner/outer sphere complexations, ion exchange, and reduction mechanisms. Besides, the cycling test showed the remarkable reusability of Ni-FeLDH@MWCNT@CA floatable microbeads for five subsequent cycles. The self-floating Ni-FeLDH@MWCNT@CA microbeads in this work provide essential support for the potential applications for the remediation of heavy metals-containing wastewater.

Toward Efficient Bactericidal and Dye Degradation Performance of Strontium- and Starch-Doped Fe2O3 Nanostructures: In Silico Molecular Docking Studies

In this study, various concentrations of strontium (Sr) into a fixed amount of starch (St) and Fe₂O₃ nanostructures (NSs) were synthesized with the co-precipitation approach to evaluate the antibacterial and photocatalytic properties of the concerned NSs. The study aimed to synthesize nanorods of Fe₂O₃ with co-precipitation to enhance the bactericidal behavior with dopant-dependent Fe₂O₃. Advanced techniques were utilized to investigate the structural characteristics, morphological properties, optical absorption and emission, and elemental composition properties of synthesized samples. Measurements via X-ray diffraction confirmed the rhombohedral structure for Fe₂O₃. Fourier-transform infrared analysis explored the vibrational and rotational modes of the O-H functional group and the C=C and Fe-O functional groups. The energy band gap of the synthesized samples was observed in the range of 2.78-3.15 eV, which indicates that the blue shift in the absorption spectra of Fe₂O₃ and Sr/St-Fe₂O₃ was identified with UV-vis spectroscopy. The emission spectra were obtained through photoluminescence spectroscopy, and the elements in the materials were determined using energy-dispersive X-ray spectroscopy analysis. High-resolution transmission electron microscopy micrographs showed NSs that exhibit nanorods (NRs), and upon doping, agglomeration of NRs and nanoparticles was observed. Efficient degradations of methylene blue increased the photocatalytic activity in the implantation of Sr/St on Fe₂O₃ NRs. The antibacterial potential for Escherichia coli and Staphylococcus aureus was measured against ciprofloxacin. E. coli bacteria exhibit inhibition zones of 3.55 and 4.60 mm at low and high doses, respectively. S. aureus shows the measurement of inhibition zones for low and high doses of prepared samples at 0.47 and 2.40 mm, respectively. The prepared nanocatalyst showed remarkable antibacterial action against E. coli bacteria rather than S. aureus at high and low doses compared to ciprofloxacin. The best-docked conformation of the dihydrofolate reductase enzyme against E. coli for Sr/St-Fe₂O₃ showed H-bonding interactions with Ile-94, Tyr-100, Tyr-111, Trp-30, ASP-27, Thr-113, and Ala-6.

Excellent removal performance of 4,4'-biphenyldicarboxaldehyde m-phenylenediamine Schiff base magnetic polymer towards phenanthrene and 9-phenanthrol: Experimental, modeling and DFT calculations studies

Phenanthrene (PTH) and 9-phenanthrol (9-PTH) exhibited severe health threats and ecological hazards, for this reason, exploring a high-efficient removing strategy for PTH and 9-PTH could be considered of great urgency. Herein the 4,4'-biphenyldicarboxaldehyde m-phenylenediamine Schiff base magnetic polymer (magnetic BIPH-PHEN) was successfully fabricated via Schiff base polycondensation reaction and the subsequently one-pot embedded method. The mutual aromatic nucleus of BIPH-PHEN polymer and PTH/9-PTH could form π-π interaction, thus improving the capture ability, the embedded Fe₃O₄ nanoparticles provided the possibility for rapid separation. The physical and chemical properties of the magnetic BIPH-PHEN were systematically characterized. The removal rate of magnetic BIPH-PHEN towards PTH and 9-PTH was 85.65 % and 98.52 %, respectively (PTH or 9-PTH: 8 mg/L; Adsorbent: 0.2 g/L). The DFT calculations including energy calculations and electrostatic potential distribution analyzed the different bonding modes and proposed the most possible bonding modes in the adsorbent/adsorbate system. Moreover, the LUMO and HOMO orbits combined with energy gaps analysis proved the existence and specific types of the π-π interaction. The monolayer adsorption occurred on the homogeneous magnetic BIPH-PHEN surface, simultaneously the chemisorption was dominant. This work not only proposed new sights on assembling magnetic Schiff base polymer for removing polycyclic aromatic hydrocarbons, but also provided a deeper understanding of intramolecular interactions.

One-Pot Environmentally Friendly Synthesis of Nanomaterials Based on Phytate-Coated Fe3O4 Nanoparticles for Efficient Removal of the Radioactive Metal Ions 90Sr, 90Y and (UO2)2+ from Water

We report the fast (three minutes) synthesis of green nanoparticles based on nanoparticles coated with the natural organic receptor phytate for the recognition and capture of ⁹⁰Sr, ⁹⁰Y, and (UO₂₎²⁺. The new material shows excellent retention for (UO₂)²⁺, 97%; these values were 73% and 100% for ⁹⁰Sr and ⁹⁰Y, respectively. Recovery of the three radioactive metal ions occurs through a non-competitive process. The new hybrid material is harmless, easy to prepare, and immobilizes these radioactive contaminants in water with great efficiency.

High-activity daisy-like zeolitic imidazolate framework-67/reduced grapheme oxide-based colorimetric biosensor for sensitive detection of hydrogen peroxide

Colorimetric biosensors, based on enzyme-like nanomaterials, have come into the spotlight in virtue of their visual detection. Herein, a daisy-like zeolitic imidazolate framework-67/reduced grapheme oxide (ZIF-67/rGO) nanozyme with unique 3D hierarchical structures has been designed to realize visual detection of hydrogen peroxide (H₂O₂) that is recognized as a strong oxidizing agent or reactive oxygen species associated with oxidative stress in biological systems. The daisy-like ZIF-67/rGO is prepared by a facile one-step liquid-phase method conducted under room temperature. The successful introduction of rGO endows the daisy-like ZIF-67/rGO nanozyme with abundant porous structure, high specific surface area, and good charge transfer capability, which significantly accelerates the adsorbability and recognition towards the substrates and the oxidation rate of TMB-H₂O₂ reaction, and thus improving the nanozyme activity observably. It is conductive to nanozyme-modulated H₂O₂ determination. The established colorimetric biosensor platform based on ZIF-67/rGO nanozyme exhibits remarkable sensitivity and high specificity for the application in visual detection of H₂O₂. The detection limit of ZIF-67/rGO-based biosensor platform is as low as 3.81 μM, which is nearly 8 times lower than that of ZIF-67-based biosensor platform. Moreover, its potential applicability as an ideal platform for colorimetric biosensors is demonstrated by testing the concentration of H₂O₂ in milk samples, which sheds light on the promising application of the proposed biosensing system in point-of-care detection.

Bipyridine containing poly(amic-acid)s: Synthesis, characterization, and sorption behavior toward the Ni (II) ions

New poly(amic-acid)s sorbents, bearing bipyridine chelating groups, were synthesized by reaction of benzophenonetetracarboxylic dianhydride (BTDA) with different percentages of 4,6-bis(4-aminophenyl)-2,2′-bipyridine (BAPB), and 1,4-phenylene diamine (PPD) and were characterized by FTIR and 1HNMR spectroscopies. Because of the imidization of these poly(amic-acid)s after about 10% weight loss, their thermal stability was raised to about 500°C. The glass transition temperatures of these polymers were in the range of 154–166°C. The sorption of Ni(II) by these sorbents from the aqueous solutions was investigated by varying different parameters such as the contact time, pH, and sorbent dosage. Results indicated that the optimum efficiencies of these sorbents toward Ni(II) were at 25°C, at pH = 4 and after about 75 min. According to the Langmuir equation, the maximum uptake capacity ( qm) of PAA30/70 as a best sorbent for nickel was 14.66 mg.g−1. The modeling results confirmed the pseudo-second-order sorption for the metal ion. The morphology of these sorbents before and after sorption of Ni(II) was investigated using Scanning Electron Microscopy and the results confirmed the porous structure of these sorbents.

[Formula: see text]

Engineered Magnetic Carbon-Based Adsorbents for the Removal of Water Priority Pollutants: An Overview

This review covers the preparation, characterization, and application of magnetic adsorbents obtained from carbon-based sources and their application in the adsorption of both inorganic and organic pollutants from water. Different preparation routes to obtain magnetic adsorbents from activated carbon, biochar, hydrochar, graphene, carbon dots, carbon nanotubes, and carbon nanocages, including the magnetic phase incorporated on the solid surface, are described and discussed. The performance of these adsorbents is analyzed for the removal of fluoride, arsenic, heavy metals, dyes, pesticides, pharmaceuticals, and other emerging and relevant water pollutants. Properties of these adsorbents and the corresponding adsorption mechanisms have been included in this review. Overall, this type of magnetic adsorbents offers an alternative for facing the operational problems associated to adsorption process in water treatment. However, some gaps have been identified in the proper physicochemical characterization of these adsorbents, the development of green and low-cost preparation methods for their industrial production and commercialization, the regeneration and final disposal of spent adsorbents, and their application in the multicomponent adsorption of water pollutants.

Magnetic solid-phase extraction using polydopamine-coated magnetic multiwalled carbon nanotube composites coupled with high performance liquid chromatography for the determination of chlorophenols

Polydopamine (PDA)-coated magnetic multiwalled carbon nanotube (M-MWCNT) composites were synthesized in two facile preparation steps, and were used as adsorbents for magnetic solid-phase extraction (MSPE) coupled with high-performance liquid chromatography (HPLC) for simultaneous extraction, enrichment and determination of five kinds of typical chlorophenols (CPs) in water samples. The as-prepared magnetic composites showed excellent magnetic properties and high thermal stability. Various main parameters influencing the extraction efficiency of MSPE were systematically investigated. Under the optimized MSPE-HPLC conditions, a high enrichment factor (EF) was obtained in the range of 85-112 for 2-chlorophenol (2-CP), 4-chlorophenol (4-CP), 2,6-dichlorophenol (2,6-DCP), 2,4-dichlorophenol (2,4-DCP) and 2,4,6-trichlorophenol (2,4,6-TCP). Good linearity was obtained in the range of 2.0-200 μg L^-1 for 2-CP and 4-CP and 1.0-200 μg L^-1 for 2,6-DCP, 2,4-DCP and 2,4,6-TCP, with a correlation coefficient (R²) higher than 0.9964. The limits of detection (LODs) and the limits of quantification (LOQs) were in the range of 0.10-0.31 μg L^-1 and 0.35-1.03 μg L^-1, respectively. The intraday and interday precisions evaluated using relative standard deviation (RSD) values were in the range of 1.05-2.25% and 1.88-2.83%, respectively. The validated MSPE-HPLC method was also successfully applied to analyze five kinds of CPs in tap water, lake water, river water and seawater samples, and satisfactory recoveries were obtained in the range of 76.87-106.5% with RSDs of 1.64-6.78%.

Effective Disposal of Methylene Blue and Bactericidal Benefits of Using GO-Doped MnO2 Nanorods Synthesized through One-Pot Synthesis

Graphene oxide (GO)-doped MnO2 nanorods loaded with 2, 4, and 6% GO were synthesized via the chemical precipitation route at room temperature. The aim of this work was to determine the catalytic and bactericidal activities of prepared nanocomposites. Structural, optical, and morphological properties as well as elemental composition of samples were investigated with advanced techniques such as X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, UV-visible (vis) spectroscopy, photoluminescence (PL), energy-dispersive spectrometry (EDS), and high-resolution transmission electron microscopy (HR-TEM). XRD measurements confirmed the monoclinic structure of MnO2. Vibrational mode and rotational mode of functional groups (O-H, C=C, C-O, and Mn-O) were evaluated using FTIR results. Band gap energy and blueshift in the absorption spectra of MnO2 and GO-doped MnO2 were identified with UV-vis spectroscopy. Emission spectra were attained using PL spectroscopy, whereas elemental composition of prepared materials was recorded with scanning electron microscopy (SEM)-EDS. Moreover, HR-TEM micrographs of doped and undoped MnO2 revealed elongated nanorod-like structure. Efficient degradation of methylene blue enhanced the catalytic activity in the presence of a reducing agent (NaBH4); this was attributed to the implantation of GO on MnO2 nanorods. Furthermore, substantial inhibition areas were measured for Escherichia coli (EC) ranging 2.10-2.85 mm and 2.50-3.15 mm at decreased and increased levels for doped MnO2 nanorods and 3.05-4.25 mm and 4.20-5.15 mm for both attentions against SA, respectively. In silico molecular docking studies suggested the inhibition of FabH and DNA gyrase of E. coli and Staphylococcus aureus as a possible mechanism behind the bactericidal activity of MnO2 and MnO2-doped GO nanoparticles (NPs).

Active and passive adsorption of 47 trace atmospheric volatile organic compounds onto carbon nanotubes

Carbon nanotubes (CNTs) of varying sizes and CNTs functionalised with carboxylic acids were examined by thermal desorption gas chromatography mass spectrometry (TD-GCMS) to determine the degree of surface contamination of atmospheric volatile organic compounds (VOCs). The CNTs could be purged of physisorbed VOCs by heating to 380 °C under a stream of purified nitrogen gas. As soon as the cleaned CNTs were exposed to atmospheric air they spontaneously adsorbed trace VOCs. As well as passive adsorption of VOCs, active sampling was carried out by pumping atmospheric air through the CNTs and comparing the results with the standard multisorbent materials Carbopack X and Tenax that are used widely for VOC trapping and analysis. The CNTs were found to trap many VOCs at a comparable level to the standard sorbent materials. Therefore, to maintain the CNTs in a pristine condition, it is recommended that they are first heated under vacuum to remove residual physisorbed VOCs, and then stored under vacuum or in a purified inert gas atmosphere.

CNTs need to be cleaned at high temperature under vacuum and stored in an inert gas environment to prevent immediate contamination by adsorbed trace atmospheric VOCs.

Pulmonary inflammatory and fibrogenic response induced by graphitized multi-walled carbon nanotube involved in cGAS-STING signaling pathway

Graphitized multi-walled carbon nanotubes (GMWCNTs) are a new type of nanomaterial. Recently, their production and application in biological medicine have grown rapidly. However, GMWCNTs may cause adverse health effects, including the common occupational disease of pulmonary fibrosis. Pulmonary fibrosis is a serious progressive disease that often leads to lung failure, high mortality, and disability, and there is no effective therapy currently available. Therefore, identifying new biomarkers of the disease is important to better understand the disease mechanisms and explore new therapeutic strategies. In this study, 40 μg of GMWCNTs was used to treat mice in vivo by pharyngeal aspiration, and different genes were screened by transcriptome sequencing. Activation of the cyclic GMP-AMP synthase (cGAS)-stimulator of interferon gene (STING) signal pathway had an important effect on the development of pulmonary inflammation and fibrosis. GMWCNTs were then administered to the mice with a STING inhibitor (C-176). Inhibition of STING effectively decreased pulmonary inflammation and fibrosis in mice induced by GMWCNTs. Collectively, activation of the cGAS-STING signaling pathway is involved in GMWCNT-induced pulmonary inflammation and fibrosis in mice.

Luminescent cellulose-based porous binary metal-organic gels in an adsorption bed for effective adsorption and sensitive detection of chlortetracycline hydrochloride

Three novel (Fe-Eu) JLUE-MOGs were successfully fabricated through a solvothermal method and employed to construct the double-effect system for antibiotics adsorption and detection. The characterizations highlighted the properties of ample active sites, large surface areas and hierarchical porous structures, which did contribute to superb and rapid chlortetracycline hydrochloride (CTC) adsorption by JLUE-MOGs. Besides, the effects of initial pH values, JLUE-MOG dosages and co-existing inorganic ions on the CTC adsorption could be explained by pore filling, π-π EDA interaction, electrostatic interaction, water affinity as well as hydrogen bonding. Moreover, the optimized condition was cross-explored by response surface methodology (RSM) with tiny differences compared to actual experiments. In addition, fluorescent JLUE-MOG-7 was implemented for sensitive recognition of CTC and reflecting adsorption processes. Furthermore, shaping JLUE-MOG-7@cellulose aerogels were fabricated as filter materials for applying into an adsorption bed. The breakthrough process was fitted well by Bohart-Adams model and Thomas model, along with recognizable fluorescence changes of immobilized adsorbents. This work develops efficient and luminescent powder-like JLUE-MOGs for antibiotics adsorptive enrichment and sensitive detection. More importantly, immobilized JLUE-MOG@cellulose aerogels, as promising and alternative adsorbents with real-time fluorescence changes, can be utilized for continuously pollutants removal in real wastewater treatment.

Magnetic Nanoparticle Composites: Synergistic Effects and Applications

Composite materials are made from two or more constituent materials with distinct physical or chemical properties that, when combined, produce a material with characteristics which are at least to some degree different from its individual components. Nanocomposite materials are composed of different materials of which at least one has nanoscale dimensions. Common types of nanocomposites consist of a combination of two different elements, with a nanoparticle that is linked to, or surrounded by, another organic or inorganic material, for example in a core-shell or heterostructure configuration. A general family of nanoparticle composites concerns the coating of a nanoscale material by a polymer, SiO2 or carbon. Other materials, such as graphene or graphene oxide (GO), are used as supports forming composites when nanoscale materials are deposited onto them. In this Review we focus on magnetic nanocomposites, describing their synthetic methods, physical properties and applications. Several types of nanocomposites are presented, according to their composition, morphology or surface functionalization. Their applications are largely due to the synergistic effects that appear thanks to the co-existence of two different materials and to their interface, resulting in properties often better than those of their single-phase components. Applications discussed concern magnetically separable catalysts, water treatment, diagnostics-sensing and biomedicine.

Functionalized Carbon Nanotubes (CNTs) for Water and Wastewater Treatment: Preparation to Application

As the world human population and industrialization keep growing, the water availability issue has forced scientists, engineers, and legislators of water supply industries to better manage water resources. Pollutant removals from wastewaters are crucial to ensure qualities of available water resources (including natural water bodies or reclaimed waters). Diverse techniques have been developed to deal with water quality concerns. Carbon based nanomaterials, especially carbon nanotubes (CNTs) with their high specific surface area and associated adsorption sites, have drawn a special focus in environmental applications, especially water and wastewater treatment. This critical review summarizes recent developments and adsorption behaviors of CNTs used to remove organics or heavy metal ions from contaminated waters via adsorption and inactivation of biological species associated with CNTs. Foci include CNTs synthesis, purification, and surface modifications or functionalization, followed by their characterization methods and the effect of water chemistry on adsorption capacities and removal mechanisms. Functionalized CNTs have been proven to be promising nanomaterials for the decontamination of waters due to their high adsorption capacity. However, most of the functional CNT applications are limited to lab-scale experiments only. Feasibility of their large-scale/industrial applications with cost-effective ways of synthesis and assessments of their toxicity with better simulating adsorption mechanisms still need to be studied.

Decorating graphene oxide with zeolitic imidazolate framework (ZIF-8) and pseudo-boehmite offers ultra-high adsorption capacity of diclofenac in hospital effluents

This study reports on an easy and scalable synthesis method of a novel magnetic nanocomposite (GO/ZIF-8/γ-AlOOH) based on graphene oxide (GO) nanosheets decorated with zeolitic imidazolate framework-8 (ZIF-8), pseudo-boehmite (γ-AlOOH), and iron oxide (Fe₃O₄) nanoparticles by combining solvothermal and solid-state dispersion (SSD) methods. The nanocomposite was successfully applied to remove of diclofenac sodium (DCF) - a widely used pharmaceutical - from water. Response Surface Methodology (RSM) was used to optimize the adsorption process and assess the interactions among the influencing factors on DCF removal efficiency; including contact time, adsorbent dosage, initial pH, solution temperature, and DCF concentration. Adsorption isotherm results showed a good fitting with the Langmuir isotherm model with an exceptional adsorption capacity value of 2594 mg g^-1 at 30 °C, which was highly superior to the previously reported adsorbents. In addition, kinetic and thermodynamic investigations further illustrated that the adsorption process was fast (equilibrium time = 50 min) and endothermic. The regeneration of GO/ZIF-8/γ-AlOOH nanocomposite using acetic acid solution (10% v/v) after a simple magnetic separation was confirmed in five consecutive cycles, which eliminate the usage of organic solvents. The nanocomposite has also shown a superior performance in treating a simulated hospital effluent that contained various pharmaceuticals as well as other organic, and inorganic constituents.

Ultrasensitive detection of cytotoxic food preservative tert-butylhydroquinone using 3D cupric oxide nanoflowers embedded functionalized carbon nanotubes

Accurate detection of cytotoxic food preservative tert-butylhydroquinone (TBHQ) has significant importance in maintaining food quality and safety. TBHQ is a chronic hazard to aquatic life and its use in applications involving direct human exposure and frequent release to environment makes its quantification critical to maintain safety. Hence, we report development of a sensitive electrochemical sensor for TBHQ determination at nanomolar level in commonly used edible oils and water sample. Novel cupric oxide (CuO) decorated amine functionalized carbon nanotubes (NH₂-CNTs) were prepared for development of TBHQ sensor. 3D CuO nanoflowers and NH₂-CNTs were synthesized using hydrothermal and ultrasound-assisted method respectively. Techniques such as SEM, elemental mapping, XRD, FTIR, micro Raman, XPS, EIS, and UV-Visible spectroscopy were taken to affirm significant characterizations of synthesized materials. We have observed outstanding electrocatalytic activity towards TBHQ detection using the sonochemically prepared nanocomposite modified screen printed carbon electrode (SPCE). The proposed sensor exhibited ultra-low detection limit at 3 nM and exceptional sensitivity at 37.7 μA μM^-1 cm^-2. Furthermore, TBHQ sensor showcased outstanding anti-interference, stability, reproducibility, and repeatability. The practical feasibility of TBHQ detection was validated using real sample analysis resulting in excellent recovery in the range 95.90-104.87% and a maximum RSD of mere 2.71%.

Cytotoxic aquatic pollutants and their removal by nanocomposite-based sorbents

Water is an extremely essential compound for human life and, hence, accessing drinking water is very important all over the world. Nowadays, due to the urbanization and industrialization, several noxious pollutants are discharged into water. Water pollution by various cytotoxic contaminants, e.g. heavy metal ions, drugs, pesticides, dyes, residues a drastic public health issue for human beings; hence, this topic has been receiving much attention for the specific approaches and technologies to remove hazardous contaminants from water and wastewater. In the current review, the cytotoxicity of different sorts of aquatic pollutants for mammalian is presented. In addition, we will overview the recent advances in various nanocomposite-based adsorbents and different approaches of pollutants removal from water/wastewater with several examples to provide a backdrop for future research.

Magnetic nanoparticle decorated anodic alumina nanotubes for fluorescent detection of cathepsin B

In this work, we present the process to provide anodic alumina nanotubes with magnetic responsivity based on magnetic nanoparticles. We demonstrate the possibility to cause the motion of these composite nanotubes under magnetic field, providing them with guided mobility. The obtained magnetic anodic alumina nanotubes are completely characterized and their potential to undergo selective and effective functionalization, and stimuli-responsive load release is demonstrated. For this purpose, protease-triggered release of fluorescent molecules loaded inside the magnetic anodic alumina nanotubes (MAANTs) by selective functionalization is performed. The inner walls of the MAANTs were selectively covered with protein padding of albumin-fluorescein isothiocyanate conjugate (FITC-BSA) through means of silanization. Protein functionalization was designed to undergo proteolytic hydrolysis in presence of cathepsin B- protease highly expressed during growth and initial stages of tumor metastasis - in order to cleave peptide bond of albumin and release fluorescent fragments of the protein. Proteolytic reaction with the enzyme is performed under acidic conditions. Presented arrangement is an exemplary combination of functionalities - which are vast - and of value for applications like drug delivery and biosensing applications.

Adsorption of As(V) and Ni(II) by Fe-Biochar composite fabricated by co-pyrolysis of orange peel and red mud

This study aimed to compare the adsorption performance of Fe-biochar composites (Fe-C-N₂ and Fe-C-CO₂), fabricated by co-pyrolysis of red mud and orange peel in N₂ and CO₂, for As(V) and Ni(II). By the syngas production comparison test, it was confirmed that CO₂ was more advantageous than N₂ as a pyrolytic medium gas to produce more CO. The resulting Fe-biochar composite showed the aggregate morphology consisting of different Fe phases (magnetite or metal Fe) from the inherent hematite phase in red mud and carbonized carbon matrix, and there was no distinct difference between the structural shapes of two Fe-biochar composites. Adsorption experiments showed that the adsorption capacities for As(V) and Ni(II) in single mode were almost similar with 7.5 and 16.2 mg g^-1 for Fe-C-N₂ and 5.6 and 15.1 mg g^-1 for Fe-C-CO₂, respectively. The adsorption ability of Fe-C-CO₂ for both As(V) and Ni(II) was further enhanced in binary adsorption mode (As(V): 13.4 mg g^-1, Ni(II):17.6 mg g^-1) through additional removal of those ions by Ni(II)-As(V) complexation. The overall results demonstrated CO₂-assisted pyrolysis can provide a viable platform to convert waste materials into fuel gases and environmental media for co-adsorption of cationic and anionic heavy metals.

Exploring the Mechanisms of Selectivity for Environmentally Significant Oxo-Anion Removal during Water Treatment: A Review of Common Competing Oxo-Anions and Tools for Quantifying Selective Adsorption

Development of novel adsorbents often neglects the competitive adsorption between co-occurring oxo-anions, overestimating realistic pollutant removal potentials, and overlooking the need to improve selectivity of materials. This critical review focuses on adsorptive competition between commonly co-occurring oxo-anions in water and mechanistic approaches for the design and development of selective adsorbents. Six "target" oxo-anion pollutants (arsenate, arsenite, selenate, selenite, chromate, and perchlorate) were selected for study. Five "competing" co-occurring oxo-anions (phosphate, sulfate, bicarbonate, silicate, and nitrate) were selected due to their potential to compete with target oxo-anions for sorption sites resulting in decreased removal of the target oxo-anions. First, a comprehensive review of competition between target and competitor oxo-anions to sorb on commonly used, nonselective, metal (hydr)oxide materials is presented, and the strength of competition between each target and competitive oxo-anion pair is classified. This is followed by a critical discussion of the different equations and models used to quantify selectivity. Next, four mechanisms that have been successfully utilized in the development of selective adsorbents are reviewed: variation in surface complexation, Lewis acid/base hardness, steric hindrance, and electrostatic interactions. For each mechanism, the oxo-anions, both target and competitors, are ranked in terms of adsorptive attraction and technologies that exploit this mechanism are reviewed. Third, given the significant effort to evaluate these systems empirically, the potential to use computational quantum techniques, such as density functional theory (DFT), for modeling and prediction is explored. Finally, areas within the field of selective adsorption requiring further research are detailed with guidance on priorities for screening and defining selective adsorbents.

The role of kaolin and kaolin/ZnO nanoadsorbents in adsorption studies for tannery wastewater treatment

In the present study, comparative studies of kaolin and kaolin/ZnO nanocomposites for the adsorption of Cr(VI), Fe(III), COD, BOD, and chloride from tannery wastewater were investigated. ZnO nanoparticles and kaolin/ZnO nanocomposites were prepared by sol-gel followed by wet-impregnation methods. The prepared adsorbents were characterized using different analytical tools such as X-ray diffraction, Fourier transforms infrared, high-resolution transmission electron microscopy, energy dispersive spectroscopy, selective area electron diffraction and Brunauer Emmett-Teller (BET) and X-ray Photoelectron Spectroscopy (XPS). The HRSEM/EDS/XPS analysis confirmed successful immobilization of clay structural network on the lattice layers of zincite hexagonal structure of ZnO nanoparticles. BET measurement showed an increase in the surface area of kaolin/ZnO nanocomposites (31.8 m²/g) when compared to kaolin (17 m²/g). Batch adsorption studies were carried out by varying the parameters such as contact time, adsorbent dosage and temperature. The maximum removal of Cr(VI) (100%), Fe(III) (98%), COD (95%), BOD (94%) and Chloride (78%) was obtained at 15 min by kaolin/ZnO composites. While 78% Cr(VI), 91% Fe(III), 91% COD, 89% BOD and 73% Chloride were removed by kaolin under the same conditions. The kaolin/ZnO nanocomposites exhibited better adsorption performance than kaolin due to higher surface area of the former than the latter. It was found that the Jovanovic isotherm model fitted the adsorption experimental data most with the highest correlation (R² > 0.99) for both nanoadsorbents and indicate the occurrence of adsorption on monolayer and heterogeneous surfaces. The mechanism for the adsorption of metal ions in tannery wastewater onto the nano-adsorbents was examined using Weber Morris intra-particle diffusion model and Boyd plot which showed that the adsorption process was both intra-particle and film diffusion controlled. The thermodynamic parameters such as enthalpy change showed that that adsorption of metal ions and other parameters was feasible, spontaneous and endothermic. The ZnO/clay nanocomposites exhibited excellent recyclable and re-useable properties even after six repeated applications and can, therefore, be applied in wastewater treatment for removal of heavy metals and other physicochemical parameters.

Study on the adsorption mechanism of benzoylurea insecticides onto modified hyperbranched polysilicon materials

Several hyperbranched polysilicon (HBPS) materials with different end group modifications were designed and synthesized and the structures were characterized. The modified HBPS polymers were applied to the adsorption of benzoylurea insecticides (BUs). The binding mode and binding energy between the HBPS and BUs were quantified and the results of an adsorption kinetics study and an adsorption thermodynamics experiment were verified by calculation and mutual verification. The adsorption mechanism of BUs onto HBPS was also discussed. The theoretical results show that the most effective way to combine the adsorbent and BUs is via hydrogen bonding when the end group is an amino group. Moreover, the most effective combination when the end group is β-cyclodextrin is the interaction of the BUs with the interior of the cavity to form a host–guest coating. The theoretical results of other end group-modified HBPS materials were also obtained and verified by adsorption experiments. In this work, an experimental method for obtaining the binding mode by theoretical calculations and then verifying it according to adsorption experiments was established.

Several hyperbranched polysilicon with different end group modifications were prepared, and the adsorption mechanism of benzoylureas onto the obtained materials were investigated based on the density functional theory and adsorption studies.

Cationic metal-organic frameworks as an efficient adsorbent for the removal of 2,4-dichlorophenoxyacetic acid from aqueous solutions

Metal-organic frameworks (MOFs) material with high surface area, good chemical stability and multi-functionality, has become an emerging adsorbent for water treatment. A novel kind of quaternary amine anionic-exchange MOFs UiO-66 namely UiO-66-NMe₃⁺ was firstly synthesized for adsorptive removal of a widely used toxic herbicide 2,4-dichlorophenoxyacetic acid (2,4-D) from aqueous solutions. The well-prepared UiO-66-NMe₃⁺ MOFs were fully characterized, and then the main parameters affecting the adsorption process including solution pH, adsorbent dosage and coexisting anions were systematically investigated. The maximum adsorption capacity of UiO-66-NMe₃⁺ toward 2,4-D reached as high as 279 mg g^-1, much higher than that of pristine UiO-66 and aminated UiO-66. The adsorption mechanism could be attributed to the electrostatic interactions efficiently enhanced by the functionalization of quaternary amine groups, combining with the π-π conjugations between the linkers in MOFs and 2,4-D molecules, leading to the better adsorption performance of UiO-66-NMe₃⁺. Additionally, the UiO-66-NMe₃⁺ could be well regenerated by simple solvent washing and exhibited a slight decline of adsorption capacity after seven successive recycle. Furthermore, satisfactory adsorption capacity and reusability of the MOFs in environmental water samples were attained. Comparing with reported activated carbon and resin materials, the UiO-66-NMe₃⁺ MOFs possessed higher adsorption capacity and shorter equilibrium time, as well as good reusability and practicality. The developed ion-exchange functionalized MOFs provided an ideal alternative for efficient adsorptive-removal of 2,4-D from complicated aqueous environment.

Facile fabrication of nanocomposites by modified carbon black loading with magnetite nanoparticles for fast removal of cadmium ions

Magnetic nanomaterials have unique advantages in heavy metal ions absorption because of their large specific surface area and easy magnetic manipulation. Carbon nanotube or graphene loaded with magnetite nanoparticles (MNPs) have been utilized to fabricate absorbents with both high absorption capacity and fast magnetic capture. Herein, cheap commercial carbon black was used as a substitute for expensive carbon nanotube or graphene to fabricate nanocomposites (CB-MNP) by modified carbon black loaded with superparamagnetic MNPs. The fabrication process is accomplished by two steps. Carbon blacks (CB) were modified by nitric acid to produce a large number of carboxyl groups on the surface and make stable aqueous dispersion. Subsequently, CB-MNPs with high water stability and fast magnetic response were facilely prepared by iron precursors (the ratio of ferrous to ferric is 1:2) added into the above CB dispersion and tuned pH = 10, finally added polyacrylic acid solution under sonication. Modified CB and CB-MNPs were characterized by transmission electron microscope (TEM), dynamic laser scattering (DLS), thermogravimetric analysis and so on. Water stability and magnetic response can be controlled by changing the proportion of CB and iron precursor. As a proof-of-concept, CB-MNPs were used for absorption removal of cadmium ions. Excellent performance was demonstrated with the removal efficiency of 71.41% and removal capacity of 39.99 mg · g−1 at the initial concentration of Cd2+ as 5 × 10−5 mol · l−1. The effects of initial concentration of Cd2+, pH value and interfering anion ions were also investigated and the results indicate the potential application of CB-MNP in fast removal of heavy metal ions.