Facile formation of metallic bismuth/bismuth oxide heterojunction on porous carbon with enhanced photocatalytic activity

Congregating Ag into γ-Bi2O3 coupled with CoFe2O4 for enhanced visible light photocatalytic degradation of ciprofloxacin, Cr(VI) reduction and genotoxicity studies

The work attempts to construct a highly effective γ-Bi2O3/CoFe2O4/Ag visible active photocatalyst for the enhanced degradation of ciprofloxacin (CIP) and Cr(VI) reduction. γ-Bi2O3/CoFe2O4/Ag photocatalyst was prepared by simple solid phase and co-precipitation methods. The nanosphere shaped CoFe2O4 photocatalyst are embedded on top of γ-Bi2O3 nanotriangle. The addition of Ag into γ-Bi2O3/CoFe2O4 heterojunction primitively facilitates the photocatalytic activity in higher rate. The quantitative analysis of photocatalyst possesses to have lower e-/h+ recombination rate compared to its counterparts. The prepared γ-Bi2O3/CoFe2O4/Ag photocatalyst showed 96.6% degradation of CIP in 220 min and 99.2% reduction of Cr(VI) in 120 min. Additionally, γ-Bi2O3/CoFe2O4/Ag showed outstanding recyclability and long-term stability with a degradation efficiency of 96.5% even after six cycles. The intermediate products formed were identified and the degradation pathway was elucidated by gas chromatography-mass spectrometry analysis. Total organic carbon measurement was carried over to assess the efficiency of complete degradation and the removal percentage was found to be 98%. The end product toxicity study towards bacteria was proven to have less toxicity level when compared to parent compound. Lastly, the genotoxicity of γ-Bi2O3/CoFe2O4/Ag photocatalyst was tested in Allium cepa and the results confirmed to have no cause of toxicity impacts. Overall, the work not only tends to provide a highly visible active γ-Bi2O3/CoFe2O4/Ag photocatalyst, but also attributes to have no further negative imprints in the environment.

Sulfonated Poly Ether Sulfone Membrane Reinforced with Bismuth-Based Organic and Inorganic Additives for Fuel Cells

This research work focuses on developing a robust polymer electrolyte membrane (PEM) with high proton efficiency toward proton exchange membrane fuel cells (PEMFCs). In this study, poly ether sulfone (PES) was sulfonated by chlorosulfonic acid to yield sulfonated poly ether sulfone (SPES) followed by incorporation with bismuth-based additives such as bismuth trimesic acid (BiTMA) and bismuth molybdenum oxide (Bi2MoO6). The composite membrane was thoroughly investigated for its structural and physicochemical properties such as FT-IR, SEM, TGA, contact angle, water uptake, oxidative stability, ion-exchange capacity, and swelling ratio. Incorporation of additives into the polymer was confirmed by XPS and XRD analysis. The proton conductance of the pristine SPES is 4.19 × 10-3 S cm-1, whereas that of the composite membrane SPES/BiTMA-10 is 10 × 10-3 S cm-1 and that of SPES/Bi2MoO6-15 is 7.314 × 10-3 S cm-1; both the composite membranes exhibit higher proton conductivity than the pristine SPES membrane. The physicochemical characteristics and impedance measurements of the electrolyte reported can be viable to the PEM membrane.

Hollow CuFe2O4/MgFe2O4 Heterojunction Boost Photocatalytic Oxidation Activity for Organic Pollutants

P-n heterojunction-structured CuFe2O4/MgFe2O4 hollow spheres with a diameter of 250 nm were synthesized using a template-free solvothermal method, and time-dependent morphological studies were carried out to investigate the hollow formation mechanism. The CuFe2O4/MgFe2O4 with a molar ratio of 1:2 (Cu:Mg) had the highest degradation efficiency with the model organic dye Acid Orange 7, with a degradation rate of 91.96% over 60 min. The synthesized CuFe2O4/MgFe2O4 nanocomposites were characterized by XRD, TEM, HRTEM, UV-vis spectroscopy, Mott–Schottky, and EIS. Due to the synthesis of the p-n heterojunction, CuFe2O4/MgFe2O4 has efficient photogenerated carriers, and the hollow structure has a higher specific surface area and stronger adsorption capacity, which is significantly better than that of CuFe2O4 and MgFe2O4 in terms of photocatalytic performance. The outstanding performance shows that the p-n heterostructure of CuFe2O4/MgFe2O4 has potential for application in wastewater degradation.

Non-Noble Plasmonic Metal-Based Photocatalysts

Solar-to-chemical energy conversion via heterogeneous photocatalysis is one of the sustainable approaches to tackle the growing environmental and energy challenges. Among various promising photocatalytic materials, plasmonic-driven photocatalysts feature prominent solar-driven surface plasmon resonance (SPR). Non-noble plasmonic metals (NNPMs)-based photocatalysts have been identified as a unique alternative to noble metal-based ones due to their advantages like earth-abundance, cost-effectiveness, and large-scale application capability. This review comprehensively summarizes the most recent advances in the synthesis, characterization, and properties of NNPMs-based photocatalysts. After introducing the fundamental principles of SPR, the attributes and functionalities of NNPMs in governing surface/interfacial photocatalytic processes are presented. Next, the utilization of NNPMs-based photocatalytic materials for the removal of pollutants, water splitting, CO₂ reduction, and organic transformations is discussed. The review concludes with current challenges and perspectives in advancing the NNPMs-based photocatalysts, which are timely and important to plasmon-based photocatalysis, a truly interdisciplinary field across materials science, chemistry, and physics.

Facile synthesis of novel Bi0-SBA-15 adsorbents by an improved impregnation reduction method for highly efficient capture of iodine gas

Development of high efficient adsorbents to capture iodine is of great significance for the active development of nuclear power. Herein, Bi⁰-SBA-15 was firstly synthesized and applied for capture of iodine gas. Bi⁰-SBA-15 materials were prepared by an improved impregnation reduction method. The benefit of this method was that the Bi⁰ nanoparticles with flocculent and spherical morphologies were loaded on the surface of SBA-15, which provide abundant active sites for iodine and improve the utilization rate of active sites, so as to attain a record high capture capacity (up to 925 mg/g within 60 min) and high stablitiy (91.2%) at 200 °C. The results demonstrated that the loading of Bi⁰ on the surface showed a significant impact on the structure of Bi⁰-SBA-15 and did greatly enhance the iodine capture. Furthermore, the high iodine capture capacity mainly derived from the chemical adsorption in the stable form of BiI₃. The obtained Bi⁰-SBA-15 materials exhibited excellent aqueous and irradiation stability. Thus, the results indicated that the new and highly efficient Bi⁰-SBA-15 was a potential radioactive iodine gas capture material.

Selective Synthesis of Bismuth or Bismuth Selenide Nanosheets from a Metal Organic Precursor: Investigation of their Catalytic Performance for Water Splitting

The development of cost-effective, functional materials that can be efficiently used for sustainable energy generation is highly desirable. Herein, a new molecular precursor of bismuth (tris(selenobenzoato)bismuth(III), [Bi(SeOCPh)3]), has been used to prepare selectively Bi or Bi2Se3 nanosheets via a colloidal route by the judicious control of the reaction parameters. The Bi formation mechanism was investigated, and it was observed that the trioctylphosphine (TOP) plays a crucial role in the formation of Bi. Employing the vapor deposition method resulted in the formation of exclusively Bi2Se3 films at different temperatures. The synthesized nanomaterials and films were characterized by p-XRD, TEM, Raman, SEM, EDX, AFM, XPS, and UV-vis spectroscopy. A minimum sheet thickness of 3.6 nm (i.e., a thickness of 8-9 layers) was observed for bismuth, whereas a thickness of 4 nm (i.e., a thickness of 4 layers) was observed for Bi2Se3 nanosheets. XPS showed surface oxidation of both materials and indicated an uncapped surface of Bi, whereas Bi2Se3 had a capping layer of oleylamine, resulting in reduced surface oxidation. The potential of Bi and Bi2Se3 nanosheets was tested for overall water-splitting application. The OER and HER catalytic performances of Bi2Se3 indicate overpotentials of 385 mV at 10 mA cm-2 and 220 mV, with Tafel slopes of 122 and 178 mV dec-1, respectively. In comparison, Bi showed a much lower OER activity (506 mV at 10 mA cm-2) but a slightly better HER (214 mV at 10 mA cm-2) performance. Similarly, Bi2Se3 nanosheets were observed to exhibit cathodic photocurrent in photoelectrocatalytic activity, which indicated their p-type behavior.

Impact of Zr-Doped Bi2O3 Radiopacifier by Spray Pyrolysis on Mineral Trioxide Aggregate

Mineral trioxide aggregates (MTA) have been developed as a dental root repair material for a range of endodontics procedures. They contain a small amount of bismuth oxide (Bi₂O₃) as a radiopacifier to differentiate adjacent bone tissue on radiographs for endodontic surgery. However, the addition of Bi₂O₃ to MTA will increase porosity and lead to the deterioration of MTA's mechanical properties. Besides, Bi₂O₃ can also increase the setting time of MTA. To improve upon the undesirable effects caused by Bi₂O₃ additives, we used zirconium ions (Zr) to substitute the bismuth ions (Bi) in the Bi₂O₃ compound. Here we demonstrate a new composition of Zr-doped Bi₂O₃ using spray pyrolysis, a technique for producing fine solid particles. The results showed that Zr ions were doped into the Bi₂O₃ compound, resulting in the phase of Bi_7.38Zr_0.62O_12.31. The results of materials analysis showed Bi₂O₃ with 15 mol % of Zr doping increased its radiopacity (5.16 ± 0.2 mm Al) and mechanical strength, compared to Bi₂O₃ and other ratios of Zr-doped Bi₂O₃. To our knowledge, this is the first study of fabrication and analysis of Zr-doped Bi₂O₃ radiopacifiers through the spray pyrolysis procedure. The study reveals that spray pyrolysis can be a new technique for preparing Zr-doped Bi₂O₃ radiopacifiers for future dental applications.

Hexagonal 2D NiCo-LDO supported on 0D CoWO4 to construct a p–n heterojunction for efficient photocatalytic hydrogen evolution

NiCo-LDO and CoWO4 form a p–n heterojunction, and the synergy between them provides a new hydrogen-producing active center for each.

Phase transformation and room temperature stabilization of various Bi2O3 nano-polymorphs: effect of oxygen-vacancy defects and reduced surface energy due to adsorbed carbon species

We report the grain growth from the nanoscale to microscale and a transformation sequence from Bi →β-Bi₂O₃→γ-Bi₂O₃→α-Bi₂O₃ with the increase of annealing temperature. The room temperature (RT) stabilization of β-Bi₂O₃ nanoparticles (NPs) was attributed to the effect of reduced surface energy due to adsorbed carbon species, and oxygen vacancy defects may have played a significant role in the RT stabilization of γ-Bi₂O₃ NPs. An enhanced red emission band was evident from all the samples attributed to oxygen-vacancy defects formed during the growth process in contrast with the observed white emission band from the air annealed Bi ingots. Based on our experimental findings, the air annealing induced oxidation of Bi NPs and transformation mechanism within various Bi₂O₃ nano-polymorphs are presented. The outcome of this study suggests that oxygen vacancy defects at the nanoscale play a significant role in both structural stabilization and phase transformation within various Bi₂O₃ nano-polymorphs, which is significant from theoretical consideration.

Synthesis, characterization, and visible-light-induced photocatalytic activity of powdered semiconductor oxides of bismuth and zinc toward degradation of Alizarin Red S

Semiconductor oxides of bismuth and zinc have been synthesized using modified sol-gel method and sol-combustion method, respectively. The synthesized catalysts were characterized by X-ray powder diffraction (XRD), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), and UV-vis spectroscopy. The photocatalytic activity of Bi₂ O₃ and ZnO was evaluated for the degradation of Alizarin Red S (ARS), as a model pollutant, at 20 mg/L level in water under visible light irradiation. The percentage of photocatalytic degradation was determined using UV-vis spectrophotometer. The photocatalytic results revealed that Bi₂ O₃ and ZnO could effectively degrade 73% and 53% of ARS, respectively, within 13 hr under visible light illumination, indicating that synthesized Bi₂ O₃ is a better photocatalyst than ZnO. Photodegradation of ARS with Bi₂ O₃ and ZnO is remarkably influenced by change in pH of the dye solution, and pH 8 was found to be the most favorable for maximum removal of ARS in case of both Bi₂ O₃ (75%) and ZnO (58%) photocatalyst. PRACTITIONER POINTS: Photocatalytic degradation of ARS dye depends on pH of the solution. Calcination temperature influences the crystallite size of prepared semiconductor oxides of bismuth and zinc. Bi₂ O₃ shows better photocatalytic degradation efficiency than ZnO under visible light illumination.

Construction of g-C3N4/WO3/MoS2 ternary nanocomposite with enhanced charge separation and collection for efficient wastewater treatment under visible light

Graphitic carbon nitride (g-C₃N₄) has enormous potentials for photocatalysis, yet it only possesses moderate activity because of excitonic effects and sluggish charge transfer. Here, we develop a novel two-dimensional g-C₃N₄/WO₃/MoS₂ (CWM) ternary nanocomposite through a facile co-calcination and a hydrothermal process to reach a highly-efficient photocatalyst for organic pollutant elimination under visible light. The WO₃ and MoS₂ nanoparticles were dispersed on the ultra-thin g-C₃N₄ nanosheets, in which the electronegative g-C₃N₄ facilitates formation of oxygen vacancies in WO₃. Compared to pure g-C₃N₄, WO₃, and binary composites, CWM exhibited higher photocatalytic activities for various organic pollutants removal under visible light irradiation. For instance, the CWM showed a removal ratio of ∼99% for RhB after only 10 min irradiation of visible light (λ > 420 nm) and nearly 100% for ciprofloxacin after 2 h of operation. The results showed that OH radicals are the main active species for organic degradation, which suggests a direct Z-scheme heterojunction in CWM that improved spatial separation of charge carries. Furthermore, the collection of electrons is significantly enhanced by MoS₂ for oxygen reduction reaction, and the increased oxygen vacancies of WO₃ further enhanced the separation of electron-hole pairs; therefore, it led to an effective suppression of charge carriers recombination. The above synergistic effects of ternary photocatalyst result in higher photocatalytic oxidation performance for wastewater treatment compared with pure WO₃, g-C₃N₄ and their binary composites.

Enhanced UV-Vis Photodegradation of Nanocomposite Reduced Graphene Oxide/Ferrite Nanofiber Films Prepared by Laser-Assisted Evaporation

Nanocomposite films of rGO/MFeO3 (M = Bi, La) nanofibers were grown by matrix-assisted pulsed laser evaporation of frozen target dispersions containing GO platelets and MFeO3 nanofibers. Electron microscopy investigations confirmed the successful fabrication of MFeO3 nanofibers by electrospinning Part of nanofibers were broken into shorter units, and spherical nanoparticles were formed during laser processing. Numerical simulations were performed in order to estimate the maximum temperature values reached by the nanofibers during laser irradiation. X-ray diffraction analyses revealed the formation of perovskite MFeO3 phase, whereas secondary phases of BiFeO3 could not be completely avoided, due to the high volatility of bismuth. XPS measurements disclosed the presence of metallic bismuth and Fe2+ for BiFeO3, whereas La2(CO3)3 and Fe2+ were observed in case of LaFeO3 nanofibers. High photocatalytic efficiencies for the degradation of methyl orange were achieved for nanocomposite films, both under UV and visible light irradiation conditions. Degradation values of up to 70% after 400 min irradiation were obtained for rGO/LaFeO3 nanocomposite thin layers, with weights below 10 µg, rGO platelets acting as reservoirs for photoelectrons generated at the surface of MFeO3.

Facile one-pot synthesis of novel hierarchical Bi2O3/Bi2S3 nanoflower photocatalyst with intrinsic p-n junction for efficient photocatalytic removals of RhB and Cr(VI)

The construction of heterojunction system can promote the separation and transfer of photogenerated electron-hole pairs, which is conducive to the degradation of sewage. In this paper, heterostructured Bi₂O₃/Bi₂S₃ nanoflowers are fabricated by a one-step hydrothermal method. The microstructure and optical absorption properties are studied through the detailed characterization of this heterojunction. The visible light photocatalytic ability of as-prepared Bi₂O₃/Bi₂S₃ heterojunctions are investigated by photocatalytic removals of RhB and Cr(VI). The results of photocatalysis indicate that removal efficiencies of RhB and Cr(VI) over Bi₂O₃/Bi₂S₃ heterojunction are higher than those of pure Bi₂O₃ and Bi₂S₃. The improved photocatalytic performance of the Bi₂O₃/Bi₂S₃ heterojunctions could be attributed to a combination of the p-n junction between the p-type Bi₂S₃ and n-type Bi₂O₃, and large specific surface areas (46.31 m² g^-1). Moreover, the probable photocatalytic mechanism of composite photocatalysts is explored in detail by active species trapping experiments, N₂ adsorption-desorption, the transient photovoltage electrochemical impedance spectroscopy and photoluminescence measurements. This work provides new insights into building of the efficient and novel heterogeneous photocatalysts and other energy-related devices.

Synthesis of Bi2O3-MnO2 Nanocomposite Electrode for Wide-Potential Window High Performance Supercapacitor

In this work, we report the synthesis of a Bi2O3-MnO2 nanocomposite as an electrochemical supercapacitor (ES) electrode via a simple, low-cost, eco-friendly, and low-temperature solid-state chemical process followed by air annealing. This as-synthesized nanocomposite was initially examined in terms of its structure, morphology, phase purity, and surface area using different analytical techniques and thereafter subjected to electrochemical measurements. Its electrochemical performance demonstrated excellent supercapacitive properties in a wide potential window. Its specific capacitance was able to reach 161 F g−1 at a current density of 1A g−1 and then showed a superior rate capability up to 10 A g−1. Furthermore, it demonstrated promising cycling stability at 5 A g−1 with 95% retention even after 10,000 charge–discharge cycles in a wide potential window of 1.3 V, evidencing the synergistic impact of both Bi2O3 and MnO2 in the Bi2O3-MnO2 ES electrode. Additionally, the practical reliability of the envisioned electrode was ascertained by the fabrication of a symmetric Bi2O3-MnO2//Bi2O3-MnO2 pencil-type supercapacitor device that displayed an energy density of 18.4 Wh kg−1 at a power density of 600 W kg−1 and a substantial cyclic stability up to 5000 cycles. Subsequently, an LED was also powered at its full brightness using three of these devices connected in series in order to demonstrate the real-time application of the Bi2O3-MnO2 ES electrode.

Enhanced performance of alkali-modified Bi2WO6/Bi0.15Ti0.85O2 toward photocatalytic oxidation of HCHO under visible light

Photocatalytic oxidation of formaldehyde (HCHO) is considered as one of the promising ways to resolve indoor air HCHO pollution. TiO₂ has been well known as the most extended application in photocatalysis due to its strong oxidizing ability and stability. Owing to high activity under visible light irradiation, TiO₂ and Bi₂O₃ doping mixed with Bi₂WO₆ was analyzed in this study. The formation of two kinds of heterojunction caused efficient charge separation, leading to the effective reduction in the recombination of photo-generated electron and hole. The special structure and enhanced performance of these catalysts were analyzed. For the first time, the loading of alkali salts was researched for photocatalytic oxidation. In order to understand the reaction mechanism of alkali salts enhanced effects, the catalysts were investigated by using BET, XRD, UV-Vis, FT-IR, SEM, and XPS. The results found more than 2 wt% of Na₂SO₄ loading and the mixed methods with different solutions were key factors affecting the performance of catalysts. Nearly 92% HCHO conversion could be completed over Bi₂WO₆/Bi_0.15Ti_0.85O₂ (Na₂SO₄), and the concentration of HCHO was only 0.07 mg/m³ for 24 h, which was below the limit of specification in China. The results also indicated that the solution mixing method was more favorable to increase the HCHO conversion due to decrease the size of Bi_0.15T_i0.85O₂ particles. The catalysts with Na₂SO₄ loading provided more surface-adsorbed oxygen that facilitated the desorption of CO₂ and markedly increased the photocatalytic oxidation of HCHO. Graphical abstract Plausible mechanism over W-Bi2WO6/ Bi0.15Ti0.85O2-Na2SO4 (1:4) catalysts.

Characterization of semiconductor photocatalysts

The long-standing popularity of semiconductor photocatalysts stimulated their characterization, which is the subject of this review aiming to help materials chemists and physicists, particularly students, to select suitable characterization methods.

Time-dependent synthesis of BiO2-x/Bi composites with efficient visible-light induced photocatalytic activity

A series of BiO_2-x/Bi nanocomposites were prepared via a time-dependent aqueous method, with the induction of lactic acid. The interaction of Bi³⁺ and C₃H₆O₃ in stock solution determined the formation of nonstoichiometric BiO_2-x as the precursor, subsequent reduction reaction at acid circumstance (pH = 3) produced combined composition of BiO_2-x nanosheets and Bi particles. Multiple valence states of Bi element (Bi⁰, Bi³⁺ and Bi⁵⁺) in the composite sample make it possible to manipulate the band structures of photocatalysts. The BiO_2-x/Bi composites with appropriate composition exhibited superior photocatalytic performance in the degradation of colorless bisphenol A (BPA) under visible-light irradiation. The O₂^- and OH radicals were detected as valid active species in the degradation process from ESR analysis. The photocatalytic mechanism over BiO_2-x/Bi composites was proposed on the consideration of electron-hole separation and the interfacial charge transfer.