Degradation of dyes by peroxymonosulfate activated by ternary CoFeNi-layered double hydroxide: Catalytic performance, mechanism and kinetic modeling

Super-Stable Mineralization of Metal Ions from Smelting Wastewater by In Situ Synthesis of NiFe-Based Layered Double Hydroxides for Catalytic Phenol Hydroxylation

The super-stable mineralization of metal ions from industrial wastewater by in situ synthesis of layered double hydroxides (LDHs) has been regarded as a sustainable approach from environmental protection and resource utilization perspectives. Herein, the study reports a super-stable mineralization of metal ions including Ni, Fe, Cr, Mn, Cu, Ca, Al, etc. from smelting wastewater by in situ synthesis of NiFe-based LDHs through facile coprecipitation. Such approach exhibits superior mineralization efficiency of metal ions simultaneously that can remove hundreds, thousands, or even tens of thousands mg/L of multiple metal ions to below the values of the Chinese National Emission Standards of Pollutants. Furthermore, the obtained NiFe-based LDHs exhibit excellent catalytic performance of phenol hydroxylation due to the mineralization of multiple metals on the laminates, where 48.24% conversion of phenol and 71.58% selectivity of dihydroxybenzenes are realized under room temperature for 3 h. This work paves a sustainable strategy for hazardous material disposal and resource utilization.

Reusable CS-Ca@PEI/CuMnO2 Hydrogel Beads for Peroxymonosulfate-Activated Degradation of Congo Red

Metal oxides can activate peroxymonosulfate (PMS) for the catalytic degradation of organic dyes. However, achieving high catalytic efficiency, structural stability, ease of recovery, and recyclability remains challenging for both research and practical applications. To address these requirements, a bimetallic oxide, CuMnO2, was synthesized using a simple hydrothermal approach and was encapsulated to create hydrogel beads, CS-Ca@PEI/CuMnO2. Subsequently, CS-Ca@PEI/CuMnO2 was used to activate PMS and establish a solid-liquid heterogeneous oxidation system (CS-Ca@PEI/CuMnO2/PMS) for the degradation of Congo red (CR). The effects of various parameters such as different systems, catalyst dosages, initial pH values, PMS concentrations, temperatures, and anion types on the catalytic degradation properties of CS-Ca@PEI/CuMnO2 for CR were systematically evaluated. The results indicated that CS-Ca@PEI/CuMnO2 has exceptional degradation capacity, achieving 91.0% degradation of CR at pH 7. After three degradation cycles, the catalyst maintained an 86.9% degradation efficiency compared to its original performance, highlighting its robust structural stability. The presence of reactive radicals, specifically 1O2 and •O2-, were confirmed through quenching experiments, X-ray photoelectron spectroscopy (XPS), and electron paramagnetic resonance spectroscopy (EPR). Liquid chromatography-tandem mass spectrometry (LC-MS) revealed ten proposed intermediates in the catalytic degradation process. Due to its exceptional catalytic performance, structural durability, recyclability, and ease of retrieval, the catalyst shows great potential for effectively removing organic pollutants from industrial wastewater.

FeCo@hydrochar nanocomposites as efficient peroxymonosulfate activator for organic pollutant degradation

Sulfate radical-based advanced oxidation processes (SR-AOPs) are renowned for their exceptional capacity to degrade refractory organic pollutants due to their wide applicability, cost-effectiveness, and swift mineralization and oxidation rates. The primary sources of radicals in AOPs are persulfate (PS) and peroxymonosulfate (PMS) ions, sparking significant interest in their mechanistic and catalytic aspects. To develop a novel nanocatalyst for SR-AOPs, particularly for PMS activation, we synthesized carbon-coated FeCo nanoparticles (NPs) using solvothermal methods based on the polyol approach. Various synthesis conditions were investigated, and the NPs were thoroughly characterized regarding their structure, morphology, magnetic properties, and catalytic efficiency. The FeCo phase was primarily obtained at [OH-] / [Metal] = 26 and [Fe] / [Co] = 2 ratios. Moreover, as the [Fe]/[Co] ratio increased, the degree of xylose carbonization to form a carbon coating (hydrochar) on the NPs also increased. The NPs exhibited a spherical morphology with agglomerates of varying sizes. Vibrating-sample magnetometer analysis (VSM) indicated that a higher proportion of iron resulted in NPs with higher saturation magnetization (up to 167.8 emu g-1), attributed to a larger proportion of FeCo bcc phase in the nanocomposite. The best catalytic conditions for degrading 100 ppm Rhodamine B (RhB) included 0.05 g L-1 of NPs, 2 mM PMS, pH 7.0, and a 20-min reaction at 25 °C. Notably, singlet oxygen was the predominant specie formed in the experiments in the SR-AOP, followed by sulfate and hydroxyl radicals. The catalyst could be reused for up to five cycles, retaining over 98% RhB degradation, albeit with increased metal leaching. Even in the first use, dissolved Fe and Co concentrations were 0.8 ± 0.3 and 4.0 ± 0.5 mg L-1, respectively. The FeCo catalyst proved to be effective in dye degradation and offers the potential for further refinement to minimize Co2+ leaching.

Activation of peroxymonosulfate with ZIF-67-derived Co/N-doped porous carbon nanocubes for the degradation of Congo red dye

In this study, porous carbon nanocubes encapsulated magnetic metallic Co nanoparticles (denoted as Co@N-PCNC) was prepared via pyrolyzing ZIF-67 nanocubes precursor at 600 °C and characterized by various technologies. It was used to activate peroxymonosulfate (PMS) to degrade Congo red (CR) dye efficiently. Over 98.45% of 50 mg L-1 CR was degraded using 0.033 mM PMS activated by 75 mg L-1 Co@N-PCNC within 12 min. The free radical quenching experiments were performed to reveal the nature of the reactive oxygen species radicals generated throughout the catalytic oxidation of CR. The effects of common inorganic anions and the water matrix on CR removal were studied. Moreover, the results of the kinetic study revealed the suitability of the pseudo-first-order and Langmuir-Hinshelwood kinetic models for illustrating CR degradation using the Co@N-PCNC/PMS system. Ultimately, the Co@N-PCNC displayed good operational stability, and after five cycles, the CR removal rate can still maintain over 90% after 12 min.

Role of biochar in superoxide-dominated dye degradation in catalyst-activated peroxymonosulphate process

In recent times, the application of biochar (BC) as an upcoming catalyst for the elimination of recalcitrant pollutants has been widely explored. Here, an iron loaded bamboo biochar activated peroxymonosulphate (PMS) process was tested for removing Congo red (CR) dye from water medium. The catalyst was synthesized using a green synthesis method using neem extracts and characterized using SEM, FTIR, and XRD. The effects of various operating parameters, including solution pH, catalyst dosage, and pollutant dosage, on dye degradation efficiency were examined. The results showed that at the optimized conditions of 300 mg L-1 PMS concentration, 200 mg L-1 catalyst dosage, and pH 6, about 89.7% of CR dye (initial concentration 10 ppm) was removed at 60 min of operation. Scavenging experiments revealed the significant contribution of O2•-, •OH, and 1O2 for dye degradation, with a major contribution of O2•-. The activation of PMS was mainly done by biochar rather than iron (loaded on biochar). The catalyst was highly active even after four cycles.

Efficient Adsorption of Methylene Blue Using a Hierarchically Structured Metal-Organic Framework Derived from Layered Double Hydroxide

The growing concerns about environmental pollution, particularly water pollution, are causing an increasing alarm in modern society. One promising approach to address this issue involves engineering existing materials to enhance their effectiveness. A one-step solvothermal reconstruction approach was used to build an eco-friendly two-dimensional (2D) AlNiZn-LDH/BDC MOF composite. The characterizations confirm the formation of a metal-organic framework (MOF) at the layered double hydroxide (LDH) surface. The resulting synthesized material, 2D AlNiZn-LDH/BDC MOF, demonstrated remarkable efficacy in decontaminating methylene blue (MB), a model cationic dye found in water systems. The removal performance of 2D AlNiZn-LDH/BDC MOF was significantly higher than that of pristine 2D AlNiZn-LDH. This improvement shows the potential to increase the adsorption capabilities of nanoporous LDH materials by incorporating organic ligands and integrating meso-/microporosity through MOF formation on their surfaces. Furthermore, their kinetic, isothermal, and thermodynamic studies elucidated the adsorption behavior of this composite material. The results of synthesized MOF showed excellent removal efficiency (92.27%) of 10 ppm of MB aqueous solution as compared to pristine LDH. Additionally, the as-synthesized adsorbent could be regenerated for six successive cycles. This method holds promise for the synthesis of novel and highly effective materials to combat water pollution, laying the groundwork for potential advancements in diverse applications.

Effective activation of peroxymonosulfate by CoCr-LDH for removing organic contaminants in water: from lab-scale to practical applications

In this study, CoCr layered double hydroxide material (CoCr-LDH) was prepared and used as an effective catalyst for peroxymonosulfate (PMS) activation to degrade organics in water. The prepared CoCr-LDH material had a crystalline structure and relatively porous structure, as determined by various surface analyses. In Rhodamine B (RhB) removal, the most outstanding PMS activation ability belongs to the material with a Co:Cr molar ratio of 2:1. The removal of RhB follows pseudo-first-order kinetics (R2 > 0.99) with an activation energy of 38.23 kJ/mol and efficiency of 98% after 7 min of treatment, and the total organic carbon of the solution reduced 47.2% after 10 min. The activation and oxidation mechanisms were proposed and the RhB degradation pathways were suggested with the key contribution of O2•- and 1O2. Notably, CoCr-LDH can activate PMS over a wide pH range of 4 - 9, and apply to a wide range of organic pollutants and aqueous environments. The material has high stability and good recovery, which can be reused for 5 cycles with a stable efficiency of above 88%, suggesting a high potential for practical recalcitrant water treatment via PMS activation by heterogeneous catalysts.

Phytoremediative adsorption methodologies to decontaminate water from dyes and organic pollutants

Persistent organic pollutants and dyes cause major problems during ecofriendly wastewater treatment. To overcome this huge problem, several techniques have been considered and in practice for the safe disposal of organic pollutants in recent years; some of them are discussed and compared herein. This review focuses on new trends for wastewater treatment and compares them with certain other techniques alongside their pros and cons; adsorption is considered the safest among them. Adsorbents derived from agri-wastes have good capacity for the removal of these contaminants owing to their great sorption capacity, high reusability, easy operation, etc. Sometimes they need some modifications for the removal of dyes, which are also discussed in this review. This capacity of adsorbents to chelate dye molecules can be affected by factors, such as pH, the concentration of dyes and adsorbents, and temperature of the system. pH has direct influence on the ionization potential and charge on the outer surface of adsorbents. The findings on isotherms, kinetics, and desorption of plant waste-based biomaterials that are safe for the ecosystem and user friendly and are used for hazardous contaminant removal from water are summarized in this review. Finally, conclusions and future perspectives are presented, and some other materials, such as CNTs and MOFs, are also discussed as efficient adsorbents for eliminating dyes from wastewater. Finally, it is predicted that the adsorption of dyes is a more feasible solution for this dye pollution problem.

A co-precipitation route for the preparation of eco-friendly Cu-Al-layered double hydroxides with efficient tetracycline degradation

The construction of novel efficient catalysts for the treatment of organic pollutants in the aqueous environment is essential. The lamellar-like Cu-Al layered double hydroxides (CuAl-LDHs) with various mole ratios were synthesized by a simple route of co-precipitation, and the corresponding degradation characteristic was tested for the removal of tetracycline (TC) using PMS activation. The degradation efficiency of TC over CuAl-LDHs increased up to 93% within 10 min for the Cu/Al mole ratio of 3:1 and almost not changed at a higher mole ratio. For further calcining the optimal catalyst at 300 ℃, the degradation efficiency of TC was found to be increased to 96%. Sulfuric radicals and singlet oxygen were analyzed to be the main reason for the change in degradation characteristics, which was proved by radical quenching experiments and electron paramagnetic resonance technique. The parameters including PMS concentration, catalyst dosage, and reaction temperature on the TC degradation as well as the degradation mechanism for PMS activation were elaborated. The best proportion of CuAl-LDHs owned splendid stability and catalytic activity after reusing, which showed enormous potential in practical application.

Quantitative structure-activity relationship(QSAR) models for color and COD removal for some dyes subjected to electrochemical oxidation

Electrochemical oxidation is an efficient method for the destruction of dyes in wastewater streams. The experimental conditions during electrochemical oxidation (EO) and molecular structure of a dye greatly influence the extent of degradation. The extent of degradation for a variety of dyes by EO can be predicted conveniently by the use of Quantitative structure-activity Relationship (QSAR) models. An abundant amount of published data on dye degradation by EO using highly variable experimental conditions lies unutilized to prepare QSAR models. In this study, an effort is made to use published experimental data on EO of aqueous dyes after applying an easy method of normalization, to prepare QSAR models for percent color and COD removal. Normalized color and COD removal were obtained by multiplying the reported removal by volume of reactor and concentration of dye; and divided by total current passed and the time of electrolysis. More than 15 molecular descriptors were computed using Schrodinger-suit 2018-3. The multiple linear regression (MLR) approach was used to develop normalized color and COD removal models. The quantum chemical descriptors: highest occupied molecular orbital energy (HOMO) and lowest unoccupied molecular orbital energy (LUMO), polar surface area (PSA), hydrogen bond donor count (HBD), and number of atoms were found significant. The statistical indices: goodness-of-fit, R² > 0.75, and internal and external validations, Q²_LOOCV and Q²_ext, > 0.5, satisfied the criteria for predictive models and indicated that the method of normalization used in this study is adequate. Developed QSAR models are quite simple, interpretable, and transparent.

Metal-carbon hybrid materials induced persulfate activation: Application, mechanism, and tunable reaction pathways

Proper wastewater treatment has always been the focus of human society, and many researchers have been working to find efficient and stable wastewater treatment technologies. Persulfate-based advanced oxidation processes (PS-AOPs) mainly rely on persulfate activation to form reactive species for pollutants degradation and are considered to be one of the most effective wastewater treatment technologies. Recently, metal-carbon hybrid materials have been diffusely used for PS activation because of their high stability, abundant active sites, and easy applicability. Metal-carbon hybrid materials can successfully overcome the shortcomings of onefold metal catalysts and carbon catalysts by combing the complementary advantages of the two components. This article reviews recent studies about metal-carbon hybrid materials-mediated PS-AOPs for wastewater decontamination. The interactions of metal and carbon materials, as well as the active sites of metal-carbon hybrid materials, are introduced first. Then, the application and mechanism of metal-carbon hybrid materials-mediated PS activation are presented in detail. Lastly, the modulation methods of metal-carbon hybrid materials and their tunable reaction pathways were discussed. The prospect of future development directions and challenges is proposed to facilitate metal-carbon hybrid materials-mediated PS-AOPs to take a step further for practical application.

Dispersed cobalt embedded nitrogen-rich carbon framework activates peroxymonosulfate for carbamazepine degradation: cobalt leaching restriction and mechanism investigation

Metal leaching is a key issue in cobalt-based catalysts/PMS systems, which results in the decline of catalytic ability and serious secondary pollution. Hence, a nitrogen-rich carbon framework with cobalt node (Co-NC-920) with low cobalt leaching was synthesized based on zeolite imidazole framework (ZIF) and g-C₃N₄ to activate peroxymonosulfate (PMS) for the degradation of carbamazepine (CBZ). With the restriction of nitrogen-rich carbon framework, cobalt can disperse better and form stable cobalt-nitrogen bonds, thus only 0.09 mg/L cobalt ions were leached in the solution. More than 99.9% of CBZ can be removed within 30 min of PMS addition. Further investigation revealed that ¹O₂, SO₄^•- and high-valent cobalt species were primarily responsible for CBZ degradation in the Co-NC-920/PMS system and different reactive oxygen species (ROS) were distinguished and quantified, finding ¹O₂ was predominant. The degradation process was realized by the coexistence of free radicals and non-free radicals. Moreover, CBZ degradation capacity of the catalyst was evaluated under the influence of common anions and in actual waterbody. Finally, the possible degradation pathways of CBZ were proposed and the toxicity of the intermediates was analyzed. This work provides a new approach for the synthesis of cobalt-based nitrogen-rich carbon catalysts with low leaching and high efficient.

Activation of peroxymonosulfate by Co-Mg-Fe layered doubled hydroxide for efficient degradation of Rhodamine B

Reactive species serve as a key to remediate the contamination of refractory organic contaminants in advanced oxidation processes. In this study, a novel heterogeneous catalyst, CoMgFe-LDH layered doubled hydroxide (CoMgFe-LDH), was prepared for an efficient activation of peroxymonosulfate (PMS) to oxidize Rhodamine B (RhB). The characterization results showed that CoMgFe-LDH had a good crystallographic structure. Correspondingly, the CoMgFe-LDH/PMS process exhibited good capacity to remove RhB, which was equivalent to degradation performance as homogeneous Co(II)/PMS process. The RhB oxidation in the CoMgFe-LDH/PMS process was well described with pseudo-first-order kinetic model. Additionally, the oxidation process presented an excellent stability, and only 0.9% leaching rate was detected after six sequential reaction cycles at pH 5.0. The effects of initial pH, CoMgFe-LDH dosage, PMS concentration, RhB concentration, and inorganic anions on the RhB degradation were discussed in detail. Quenching experiments showed that sulfate radicals (SO₄^•-) acted as the dominant reactive species. Further, the removal of RhB from simulated wastewater was explored. The removal efficiency of RhB (90 μM) could reach 94.3% with 0.8 g/L of catalyst and 1.2 mM of PMS addition at pH 5.0, which indicated the CoMgFe-LDH/PMS process was also effective in degrading RhB in wastewater.

Enhanced Heterogeneous Catalytic Activity of Peroxymonosulfate for Rhodamine B Degradation via a CoII-Based Metal-Organic Framework

A stable metal-organic framework with the formula {[Co(BBZB)(IPA)]·H₂O}_n (JXUST-23, BBZB = 4,7-bis(1H-benzimidazole-1-yl)-2,1,3-benzothiadiazole and H₂IPA = isophthalic acid) was constructed by incorporating Co²⁺ ions and two conjugated ligands under solvothermal conditions. JXUST-23 takes a dinuclear cluster-based layer structure with a porosity of 2.7%. In this work, JXUST-23 was used to activate peroxymonosulfate (PMS) to degrade rhodamine B (RhB), a difficult-to-degrade pollutant in water. Compared with pure PMS or JXUST-23, the JXUST-23/PMS system displays the best degradation ability of RhB in neutral solution. When the mass ratio of JXUST-23 to PMS was 2:3, 99.72% of RhB (50 ppm) was removed within 60 min, and the reaction rate was 0.1 min^-1. Furthermore, free radical quenching experiments show that SO₄^•- was the main free radical during the process of RhB degradation. In addition, JXUST-23 exhibits good reusability for the degradation of the organic dye RhB, making it a potential candidate for environmental remediation.

Pretreatment of membrane dye wastewater by CoFe-LDH-activated peroxymonosulfate: Performance, degradation pathway, and mechanism

When a membrane is used to treat dye wastewater, dye molecules are continually concentrated at the membrane surface over time, resulting in a dramatic decrease in membrane flux. Aside from routine membrane cleaning, the pretreatment of dye wastewater to degrade organic pollutants into tiny molecules is a facile solution to the problem. In this study, the use of layered double hydroxide (LDH) to activate peroxymonosulfate (PMS) for efficient degradation of organic pollutant has been thoroughly investigated. We utilized a simple two-drop co-precipitation process to prepare CoFe-LDH. The transition metal components in CoFe-LDH effectively activate PMS to create oxidative free radicals, and the layered structure of LDH increases the number of active sites, and thereby considerably enhancing the reaction rate. It was found that the reaction process produced non-free and free radicals, including singlet oxygen (¹O₂), sulfate radicals (SO₄^•-), and hydroxyl radicals (•OH), with ¹O₂ being the dominant reactive species. Under the optimal conditions (pH 6.7, PMS dosage 0.2 g/L, catalyst loading 0.1 g/L), the degradation of Acid Red 27 dye in the CoFe-LDH/PMS system reached 96.7% within 15 min at an initial concentration of 200 mg/L. The CoFe-LDH/PMS system also exhibited strong resistance to inorganic ions and pH during the degradation of organic pollutants. This study presents a novel strategy for the synergistic treatment of dye wastewater with free and non-free radicals produced by LDH-activated PMS in a natural environment.

Mechanistic insights into efficient peroxymonosulfate activation by NiCo layered double hydroxides

The efficient removal of organic refractory pollutants such as dyes and antibiotics in wastewater is crucial for protecting the environment and human health. In this work, a NiCo-layered double hydroxide (NiCo-LDH) with a uniform microspherical, hierarchical structure and a high surface area was successfully synthesized as an effective peroxymonosulfate (PMS) activator for the degradation of various organic dyes and antibiotics. The influence of various parameters on the catalytic activity of the NiCo-LDH was determined. Radical scavenger studies unveiled the major reactive oxygen species (ROSs) generated in the NiCo-LDH/PSM system to be ¹O₂, SO₄^•-, and O₂^•-. Ex-situ X-ray photoelectron spectroscopy (XPS) analysis uncovered the role of Co sites and oxygen vacancy as active sites and revealed the reversible redox properties of NiCo-LDH based on Co²⁺/Co³⁺ cycles. The activation mechanism and Rhodamine B (RhB) degradation pathways were experimentally studied and proposed. The NiCo-LDH is highly versatile, reusable and stable as shown by post-catalysis characterizations. This work shows the excellent catalysis performances and provides insights into the activation mechanism of PMS by NiCo-LDH for organic pollutant remediation.

Synthesis of MgNiCo LDH hollow structure derived from ZIF-67 as superb adsorbent for Congo red

Adsorption materials with large specific surface area and porous structures exert a beneficial impact on improving the adsorption performance. In this work, MgNiCo LDH hollow structure (MNC HS) is fabricated through a simple one-step solvothermal method using ZIF-67 as the sacrificial template. Electron microscopy shows that the MNC HS retains the dodecahedral shape of ZIF-67. The as-prepared sample exhibits efficient adsorption for Congo red (CR) in water, which is due to the hierarchical structure and large specific surface area that provides more adsorption sites and electrostatic interaction. The CR adsorption process fits the pseudo-second-order model better by kinetics simulation; while Langmuir model is more accurate than Freundlich model in describing the adsorption isotherms of CR. The maximum adsorption capacity calculated by the Langmuir model can reach 1194.7 mg g^-1, which is much higher than that of the sample MgNiCo LDH (MNC) synthesized by conventional methods. The cycle tests also show that the as-prepared adsorbent has good stability and recycling ability.

Enhancement strategies for efficient activation of persulfate by heterogeneous cobalt-containing catalysts: A review

As a clean and efficient technology for the degradation of organic contaminants, sulfate radical based advanced oxidation processes (SR-AOPs) have attracted more and more attention in the past decades. Cobalt is regarded as the most reactive and efficient non-noble metal catalyst for the activation of persulfate including peroxymonosulfate (PMS) and peroxydisulfate (PDS) to produce sulfate radicals. Due to the limitations of homogeneous catalytic systems, the heterogeneous cobalt-containing catalysts have been emerged and rapidly developed. Various strategies have been schemed to further enhance the activation ability of persulfate by heterogeneous cobalt-containing catalysts. This paper provides an overview on the recent progress in enhancement strategies for the highly efficient activation of persulfate by heterogeneous cobalt-containing catalysts. With a brief introduction on the chemistry and feature of sulfate radical reactions catalyzed by homogeneous Co²⁺/Co³⁺ species, the main strategies for enhancing persulfate activation by heterogeneous cobalt-containing catalysts are summarized, such as surface and morphology design, multiple reactive centers design, organic-inorganic hybrids and heterostructure composites. Future perspectives of heterogeneous SR-AOPs systems catalyzed by cobalt-containing catalysts are outlined.

Layered double hydroxide based materials applied in persulfate based advanced oxidation processes: Property, mechanism, application and perspectives

Recently, persulfate-based advanced oxidation processes (persulfate-AOPs) are booming rapidly due to their promising potential in treating refractory contaminants. As a type of popular two-dimensional material, layered double hydroxides (LDHs) are widely used in energy conversion, medicine, environment remediation and other fields for the advantages of high specific surface area (SSA), good tunability, biocompatibility and facile fabrication. These excellent physicochemical characteristics may enable LDH-based materials to be promising catalysts in persulfate-AOPs. In this work, we make a summary of LDHs and their composites in persulfate-AOPs from different aspects. Firstly, we introduce different structure and important properties of LDH-based materials briefly. Secondly, various LDH-based materials are classified according to the type of foreign materials (metal or carbonaceous materials, mainly). Latterly, we discuss the mechanisms of persulfate activation (including radical pathway and nonradical pathway) by these catalysts in detail, which involve (i) bimetallic synergism for radical generation, (ii) the role of carbonaceous materials in radical generation, (iii) singlet oxygen (¹O₂) production and several special nonradical mechanisms. In addition, the catalytic performance of LDH-based catalysts for contaminants are also summarized. Finally, challenges and future prospects of LDH-based composites in environmental remediation are proposed. We expect this review could bring new insights for the development of LDH-based catalyst and exploration of reaction mechanism.

Cu-doped Ni-LDH with abundant oxygen vacancies for enhanced methyl 4-hydroxybenzoate degradation via peroxymonosulfate activation: key role of superoxide radicals

Oxygen vacancies (OVs) were introduced into Ni-based layered double hydroxides (LDHs) through Cu doping, and the catalytic performance of the resulting Ni_xCu-LDHs were investigated for peroxymonosulfate (PMS) activation and methyl 4-hydroxybenzoate (MeP) degradation. Compared with that of Ni-LDH, the catalytic performance of Ni_xCu-LDHs were significantly enhanced and increased with increasing OV content in the catalysts, indicating that Cu doping introduced OVs into Ni_xCu-LDHs and greatly improved their catalytic activity with PMS. Quenching experiments and EPR analyses confirmed that oxidation processes dominated by superoxide radicals (O₂^•-) and singlet oxygen (¹O₂), rather than sulfate radicals (SO₄^•-) or hydroxyl radicals (•OH) used by traditional LDH catalysts, were responsible for MeP degradation by Ni₁₅Cu-LDHs. In addition, quenching experiments with different systems showed the fate of reduced SO₄^•-and •OH, and demonstrated that O₂^•- and ¹O₂ concentrations grew with increasing OV content, confirming that the presence of OVs affected the process of PMS activation. Notably, O₂^•- mainly originated from adsorbed oxygen or dissolved oxygen (DO) by acquiring electrons from OVs in Ni₁₅Cu-LDHs, since OVs possess abundant localized electrons. Consequently, an OV-mediated oxidative mechanism was proposed for Ni₁₅Cu-LDHs/PMS. This study provides new clues for enhancing the catalytic performance of LDH catalysts by introducing OVs via metal doping in PMS-based AOPs systems.

Efficient degradation of Rhodamine B by magnetically recoverable Fe3O4-modified ternary CoFeCu-layered double hydroxides via activating peroxymonosulfate

Environment-friendly nano-catalysts capable of activating peroxymonosulfate (PMS) have received increasing attention recently. Nevertheless, traditional nano-catalysts are generally well dispersed and difficult to be separated from reaction system, so it is particularly important to develop nano-catalysts with both good catalytic activity and excellent recycling efficiency. In this work, magnetically recoverable Fe₃O₄-modified ternary CoFeCu-layered double hydroxides (Fe₃O₄/CoFeCu-LDHs) was prepared by a simple co-precipitation method and initially applied to activate PMS for the degradation of Rhodamine B (RhB). X-ray diffraction (XRD), fourier transform infrared spectrometer (FT-IR), scanning electron microscope (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller method (BET), and vibrating sample magnetometer (VSM) were applied to characterize morphology, structure, specific surface area and magnetism. In addition, the effects of several key parameters were evaluated. The Fe₃O₄/CoFeCu-LDHs exhibited high catalytic activity, and RhB degradation efficiency could reach 100% within 20 min by adding 0.2 g/L of catalyst and 1 mmol/L of PMS into 50 mg/L of RhB solution under a wide pH condition (3.0-7.0). Notably, the Fe₃O₄/CoFeCu-LDHs showed good super-paramagnetism and excellent stability, which could be effectively and quickly recovered under magnetic condition, and the degradation efficiency after ten cycles could still maintain 98.95%. Both radicals quenching tests and electron spin resonance (ESR) identified both HO• and SO₄^•- were involved and SO₄^•- played a dominant role on the RhB degradation. Finally, the chemical states of the sample's surface elements were measured by X-ray photoelectron spectroscopy (XPS), and the possible activation mechanism in Fe₃O₄/CoFeCu-LDHs/PMS system was proposed according to comprehensive analysis.

MgCr-LDH Nanoplatelets as Effective Oxidation Catalysts for Visible Light-Triggered Rhodamine B Degradation

In this work, we successfully exfoliated MgCr-(NO3−) LDH with large purity by a simple formamide method followed by post-hydrothermal treatment and characterized by different physico-chemical techniques. The UV-DRS study persuades the red-shifted absorption band and suitable band gap of MgCr-(NO3−) LDH for optimum light harvestation ability related to the optical properties. Alternatively, the production of elevated photocurrent density of MgCr-(NO3−) LDH (3:1, 80 °C) in the anodic direction was verified by the LSV study, which further revealed their effective charge separation efficacy. These MgCr-LDH nanosheets (3:1, 80 °C) displayed the superior Rhodamine B (RhB) degradation efficiency of 95.0% at 0.80 kW/m2 solar light intensity in 2 h. The tremendous catalytic performances of MgCr-LDH (3:1, 80 °C) were typically linked with the formation of surface-active sites for the charge trapping process due to the presence of uncoordinated metallocenters during the exfoliation process. Furthermore, the maximum amount of the active free atoms at the edges of the hexagonal platelet of MgCr-LDH causes severance of the nanosheets, which generates house of platelets of particle size ~20–50 nm for light harvestation, promoting easy charge separation and catalytic efficiency. In addition, radical quenching tests revealed that h+ and •OH play as major active species responsible for the RhB degradation.

Recent advances in cobalt-activated sulfate radical-based advanced oxidation processes for water remediation: A review

Sulfate radical-based advanced oxidation processes (SR-AOPs) have attracted increasing attention for the degradation of organic contaminants in water. The oxidants of SR-AOPs could be activated to generate different kinds of reactive oxygen species (ROS, e.g., hydroxyl radicals (OH), sulfate radicals (SO₄^-), singlet oxygen (¹O₂), and superoxide radicals (O₂^-)) by various catalysts. As one of the promising catalysts, cobalt-based catalysts have been extensively investigated in catalytic activity and stability during water remediation. This article mainly summarizes recent advances in preparation and applications of cobalt-based catalysts on peroxydisulfate (PDS)/peroxymonosulfate (PMS) activation since 2016. The review covers the development of homogeneous cobalt ions, cobalt oxides, supported cobalt composites, and cobalt-based mixed metal oxides for PDS/PMS activation, especially for the latest nanocomposites such as cobalt-based metal-organic frameworks and single-atom catalysts. This article also discussed the activation mechanisms and the influencing factors of different cobalt-based catalysts for activating PDS/PMS. Finally, the future perspectives on the challenges and applications of cobalt-based catalysts are presented at the end of this paper.

Unveiling the exceptional synergism-induced design of Co-Mg-Al layered triple hydroxides (LTHs) for boosting catalytic activity toward the green synthesis of indol-3-yl derivatives under mild conditions

The current study provides a novel insight into the role of synergism of the changes in Mg²⁺/ Al³⁺ in the best catalytic activity of indol-3-yl derivatives. A series of Co-Mg-Al layered triple hydroxides (LTHs) catalysts were produced by altering the Al³⁺/Mg²⁺ ratio with respect to Co²⁺. The physicochemical properties of LTHs were well characterized by ICP-AES, XRD, FTIR, FE-SEM, BET, Zeta-sizer, and VSM. The results show that the sample CMA4 (Co²⁺:Mg²⁺:Al³⁺ 2:4:4) is an exception to the physicochemical characteristics of the produced Co-Mg-Al LTHs, which is due to the synergism between the changes in Mg²⁺ and Al³⁺. To the best of our knowledge, this is the first study to report the synthesis of indol-3-yl derivatives from indole-3-carbaldehyde using Co-Mg-Al LTHs as highly efficient heterogeneous catalysts, which is an extremely appealing path. The selectivity of the synthesis was studied by condensing various nucleophiles through the one-pot method that established superior reactivity under mild conditions. Notably, the results show that the Co-Mg-Al LTHs system exhibited an extraordinarily catalytic activity, with the highest yield (98%) being obtained under the following optimal conditions: the concentration of Co-Mg-Al LTHs = 5 mol%, 30 min., water/ethanol as solvent. Furthermore, the reusable studies exhibited that the catalysts were found to be stable and reusable for up to six cycles without substantial loss of catalytic activity. Finally, a plausible reaction mechanism of the Co-Mg-Al LTHs system for indol-3-yl derivatives was put forward according to our comprehensive analysis. Our work illuminates a cheap and flexible strategy for the synthesis of indol-3-yl derivatives using Co-Mg-Al LTHs.

Dual radicals-enhanced wet chemical oxidation of non-biodegradable chemicals

Total organic carbon (TOC) has been suggested and utilized as an index of organic matter in aqueous phases. The overall performance of TOC is highly dependent on the method of oxidation of organic matter to carbon dioxide, such as high-temperature combustion (HTC) and wet chemical oxidation (WCO). HTC requires more energy and maintenance cost, it is a major barrier to the field application. In contrast, WCO is more suitable for the application of on-line monitoring systems due to requiring lower energy and easy maintenance. However, WCO shows lower oxidation than HTC, thus, oxidation performance should be improved for the application to the field. In this study, a dual radical system (DRS), including sulfate and hydroxyl radicals, was proposed to enhance oxidation ability. The DRS uses alkaline pH and persulfate to generate sulfate radicals, which have been used to activate hydroxyl radicals and oxidize organic matter. The oxidation mechanism for the DRS has been verified using model chemicals with different reaction rate constants. The applicability of the DRS has been confirmed using authentic wastewater with a high concentration of chloride. In this study, the DRS showed similar performance compared to the HTC within 10 % error range. The DRS shows similar oxidation performance with HTC even at a high concentration of chloride. DRS did not show interference by the presence of chloride up to 30,000 mg/L of chloride. Results of this study indicate that the DRS can enhance overall oxidation performance compared to the conventional WCO system.

Sonophotocatalytic activities of FeCuMg and CrCuMg LDHs: Influencing factors, antibacterial effects, and intermediate determination

Herein, FeCuMg and CrCuMg layered double hydroxides (LDHs) were synthesized and their sonophotocatalytic activities toward Acid blue 113 (AB113) were compared. Sonolysis alone (only ultrasound) led to the decolorization efficiency of 13.0 %. A similar result was obtained in the case of the utilization of photolysis alone using a 10-W LED lamp (13.5 %). The adsorption process of AB113 onto both compounds was not efficient to significantly remove the target contaminant. The bandgap energy of 2.54 eV and 2.41 eV was calculated for FeCuMg and CrCuMg LDHs, respectively, indicating relatively higher photocatalytic activity of Cr-incorporated LDH than FeCuMg LDH. The sonophotocatalysis of AB113 (50 mg L^-1) over CrCuMg LDH (81.1 %) was more efficient than that of FeCuMg LDH (57.3 %) within the reaction time of 60 min. Intermediate byproducts of the sonophotocatalytic decomposition of organic dye over the as-synthesized tri-metal layered sonophotocatalysts were also identified. Furthermore, the antibacterial activity of both LDHs was evaluated by the CFU technique and the MBC and MIC values were determined. The antibacterial assessment confirmed the higher antibacterial activity of CrCuMg LDH than that of FeCuMg LDH against Staphylococcus aureus (S. aureus).

Efficient degradation of lomefloxacin by Co-Cu-LDH activating peroxymonosulfate process: Optimization, dynamics, degradation pathway and mechanism

In this study, bimetal layered double hydroxides (Co_xCu_y-LDHs) containing a carbonate interlayer were synthesized using coprecipitation with a variety of Co/Cu mole ratios. Meanwhile, the corresponding layered double oxides (Co_xCu_y-LDOs) were prepared as controls. In this study, Electrical energy per order was performed to evaluate economic analysis. Correspondingly, we found that Co_xCu_y-LDHs possessed a significantly better PMS activation capability than the corresponding metal oxide composite (Co₃O₄/CuO). Compared with other Co_xCu_y-LDHs, Co₂Cu₁ LDH possessed the best PMS activation capability for LOM degradation and the lowest electrical energy per order (EE/O) value during the reaction. Additionally, Co₂Cu₁ LDH presented an excellent stability and worked over a wide pH range. The hydroxide states of Co(III), Co(II), Cu(I) and Cu(II) were all able to activate PMS, indicating that there were many active sites on the surface of Co₂Cu₁ LDH. The involvement of radicals in this reaction system was determined via scavenger experiments and electron paramagnetic resonance (EPR). Meanwhile, it's worth noting that a mathematical model was developed to quantify the involvement of SO₄^- and OH. Subsequently, we determined PMS activation mechanism and LOM decomposition pathway for the PMS/Co₂Cu₁ LDH system.

Efficient degradation of tetracycline by CoFeLa-layered double hydroxides catalyzed peroxymonosulfate: Synergistic effect of radical and nonradical pathways

Advanced oxidation technologies based on peroxymonosulfate (PMS) have attracted increasing attention because of their high reactivity and selectivity. Herein, we reported a novel CoFeLa-LDH catalyst, which exhibited excellent performance to activate PMS for tetracycline (TC) elimination. The influence of extra addition, simulation wastewater tests and the reusability experiments were investigated in detail. Remarkably, the quenching experiments and the results of EPR demonstrated the synergistic effect of radical and nonradical pathways in the TC degradation. Free radicals (SO₄- and HO) played predominant roles in the first 1 min, and then both free and non-free radicals (¹O₂) interacted with TC. The possible TC degradation pathways were proposed on basis of the intermediates, which were analyzed by UPLC-QTOF-MS/MS. Finally, the reaction mechanisms of TC degradation in CoFeLa-LDH₂/PMS system were proposed according to the comprehensive analysis.

Novel zero-valent Co-Fe encapsulated in nitrogen-doped porous carbon nanocomposites derived from CoFe2O4@ZIF-67 for boosting 4-chlorophenol removal via coupling peroxymonosulfate

Environment-friendly treatment process relies on the robustness, durability, and performance of catalysts to drive the development of cutting-edge sustainable technologies for the elimination of refractory contaminants. Herein, nanocomposites prepared from zero-valent Co-Fe encapsulated in nitrogen-containing carbon (NC) nanoparticles (CFNC-30 NPs) derived from CoFe₂O₄@zeolitic imidazolate frameworks-67 were successfully prepared through pyrolysis integrated with self-reduction, and further utilized as the novel catalysts to degrade 4-chlorophenol (4-CP) by coupling with peroxymonosulfate (PMS). Three optimized parameters (CFNC-30 NPs dosage of 0.089 g L^-1, PMS concentration of 1.1 g L^-1, and initial pH of 6.6) were obtained via response surface methodology by using the Box-Behnken design model. Benefiting from the larger specific surface area, pore-volume, and existence of abundant hydroxyl groups, CFNC-30 NPs with more available active sites exhibited an excellent efficiency of 99.1% toward catalytic degradation of 4-CP within 30 min under the optimal conditions. Moreover, CFNC-30 NPs demonstrated durability and long-term stability even during the five consecutive cycle tests without a significant drop in its catalytic performance. The scavenging experiments and electron paramagnetic resonance technologies revealed that non-radical singlet oxygen (¹O₂), sulfate radicals (SO₄^-), and hydroxyl radicals (HO) were involved as active species in the CFNC-30/PMS system, contributing 46.8, 35.6, and 17.6% efficiency toward 4-CP degradation, respectively. Besides, the reaction mechanism on the CFNC-30 NPs and degradation pathways toward 4-CP were speculated under PMS activation. The results indicated that the synergistic effects between zero-valent Co-Fe and NC structures not only significantly boosted the removal efficiency and long-term stability of CFNC-30 NPs, but also facilitated the redox cycles of Co³⁺/Co²⁺ and Fe³⁺/Fe²⁺. This proof-of-concept approach to develop such high-efficient zero-valent Co-Fe encapsulated in NC structures opens up novel avenues for wastewater decontamination via PMS activation.

Fabrication and Characterization of Novel ZnAl-Layered Double Hydroxide for the Superadsorption of Organic Contaminants from Wastewater

An imidazole ester skeleton (zeolitic imidazolate framework (ZIF)) was grown on the surface of a ZnAl-layered double hydroxide (ZnAl-LDH) material to form a porous composite (ZIF-ZnAl-LDH). To understand the adsorption characteristics of the two materials, the effects of pH, adsorption time, and adsorption concentration on the adsorption of Congo red (CR) solution were investigated comprehensively. In addition, ZnAl-LDH and ZIF-ZnAl-LDH were characterized by Fourier transform infrared (FTIR), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), and X-ray photoelectron spectroscopy (XPS). The results clearly showed that ZnAl-LDH had a lamellar structure with a diameter of approximately 200-500 nm and ZIF-ZnAl-LDH had a regular three-dimensional hexagonal structure. The kinetics and thermodynamics of the CR adsorption by ZnAl-LDH and ZIF-ZnAl-LDH can be described using pseudo-second-order (PSO) and Langmuir models, respectively. The highest value of adsorption capacity obtained from the Langmuir equation was equal to 625.00 and 909.09 mg/g for these two compounds, respectively. The values of the standard Gibbs free energy (ΔG°), entropy (ΔS°), and enthalpy (ΔH°) obtained for these adsorption processes prove that the adsorption of CR by ZnAl-LDH and ZIF-ZnAl-LDH is a spontaneous endothermic process. Furthermore, through the analysis of the characterization results, it is concluded that the adsorption mechanisms of ZnAl-LDH and ZIF-ZnAl-LDH on CR are mainly dominated by electrostatic action, functional group action, surface pore adsorption, and anion exchange.

Yolk-shell ZIFs@SiO2 and its derived carbon composite as robust catalyst for peroxymonosulfate activation

Cobalt-based Zeolitic imidazolate frameworks (ZIFs) have shown a great potential for radical production by activating peroxymonosulfate (PMS). However, improve the stability of ZIFs in the reaction remains a significant challenge. In this work, ZIF-67 was synthesized and protected by coating with a layer of silica, furthermore, the yolk-shell ZIFs@SiO₂ was carbonized under inner gas to obtain the Co containing carbon. When the above samples were applied for catalytic degradation of Rhodamine B (RhB) in the presence of PMS, both of them shows similar performance, with higher RhB removal efficiency and stability than that of pure ZIF-67. Additionally, factors affecting the PMS activation such as catalyst and PMS dosage and solution pH were also investigated. Radical quenching tests and electron paramagnetic resonance (EPR) revealed that ¹O₂ was the dominant active species involving in the degradation process. Finally, the reusability of the catalysts was studied and the spent catalysts were analyzed. Overall, the results provide insights into synthesis of yolk-shell ZIFs@SiO₂ catalyst with enhanced performance for the degradation of organic pollutants from effluent.

Facilely synthesized cobalt doped hydroxyapatite as hydroxyl promoted peroxymonosulfate activator for degradation of Rhodamine B

Hydroxyapatite (HAP) is a promising supporter of catalyst due to its potential in immobilizing metals stably. HAP supported cobalt-based catalyst (Co-HAP) was synthesized via a facile ion exchange-calcination method to reduce the Co leaching. The synthesized Co-HAP was characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Transmission electron microscope (TEM), Brunauer-Emmett-Teller (BET) analysis and X-ray photoelectron spectroscopy (XPS). Cobalt ions were incorporated into HAP structure and Co₃O₄ on HAP surface. Co-HAP showed satisfactory performance in peroxymonosulfate (PMS) activation for eliminating Rhodamine B (RhB) in aqueous solution. Co-HAP even revealed a better activity than that of CoFe₂O₄. •OH, SO₄^•- and ¹O₂ were all involved in RhB degradation and ¹O₂ played a leading role. High content of surface oxygen groups could be found on Co-HAP after RhB degradation, which might be resulted from the high amounts of hydroxyl groups. The presence of hydroxyl groups performed the co-catalytic activity of PMS activation in Co-HAP/PMS system.

Adsorption Process and Properties Analyses of a Pure Magadiite and a Modified Magadiite on Rhodamine-B from an Aqueous Solution

The result of an adsorption experiment indicated that the pure magadiite (MAG) and the modified MAG via cetyltrimethylammonium-bromide (CTAB-MAG) possessed pronounced affinity to the Rhodamine-B (Rh-B) dye molecules. CTAB-MAG was synthesized with an ion-exchange method between MAG and cetyltrimethylammonium-bromide (CTAB) in an aqueous solution. The adsorption capacities of CTAB-MAG and MAG on Rh-B were 67.19 mg/g and 48.13 mg/g, respectively; while the pH and the time were 7 and 60 min, respectively; however, the initial concentration of Rh-B was 100 mg/L, and adsorbent dosage was 1 g/L. Whereas, the adsorption capacity of CTAB-MAG was increased by 40% over MAG which indicated that CTAB-MAG can be used as an efficient low-cost adsorbent. Adsorption kinetics were consistent with the pseudo-second-order kinetic equation; the adsorption processes were dominated by film diffusion process which belonged to monomolecular layer adsorption.

Oxidation Mechanisms of the UV/Free Chlorine Process: Kinetic Modeling and Quantitative Structure Activity Relationships

Recently, the UV/free chlorine process has gained attention as a promising technology for destroying refractory organic contaminants in the aqueous phase. We have developed a kinetic model based on first-principles to describe the kinetics and mechanisms of the oxidation of organic contaminants in the UV/free chlorine process. Substituted benzoic acid compounds (SBACs) were chosen as the target parent contaminants. We determined the second-order rate constants between SBACs and reactive chlorine species (RCS; including [Formula: see text], [Formula: see text] and [Formula: see text]) by fitting our model to the experimental results. We then predicted the concentration profiles of SBACs under various operational conditions. We analyzed the kinetic data and predicted concentration profiles of reactive radicals ([Formula: see text] and RCS), we found that [Formula: see text] was the dominant radicals for SBACs destruction. In addition, we established quantitative structure activity relationships (QSARs) that can help predict the second-order rate constants for SBACs destruction by each type of reactive radicals using SBACs Hammett constants. Our first-principles-based kinetic model has been verified using experimental data. Our model can facilitate a design for the most cost-effective application of the UV/free chlorine process. For example, our model can determine the optimum chlorine dosage and UV light intensity that result in the lowest energy consumption.

Rate constants of sulfate radical anion reactions with organic molecules: A review

The rate constants of sulfate radical anion reaction (k_SO4-) with about 230 organic molecules of environmental interest are tabulated and discussed, together with both the methods of rate constant determinations and the reaction mechanisms. k_SO4-'s were collected from the original publications. The highest values in the ∼10⁹ M^-1 s^-1 range are published for aromatic molecules. There is a tendency that electron donating substituents increase and electron withdrawing substituents decrease these values. There are just a few compounds with rate constants established using different techniques in different laboratories. k_SO4-'s determined in different laboratories by the direct techniques, pulse radiolysis or laser flash photolysis, in most cases agree reasonably. The values determined by competitive experimental techniques, by complex kinetics calculations, or by modelling show a large scatter. Some of these techniques seem to be questionable for k_SO4- determination. The sulfate radical anion reacts with ketone and amine moieties of molecules by electron transfer. The same mechanism is also suggested for the reaction with aromatic rings. However, in a few cases addition to the double bond and sulfate anion elimination reactions were distinguished. A typical reaction with the aliphatic parts of the molecule is H-abstraction.

Co3O4 nanocrystals/3D nitrogen-doped graphene aerogel: A synergistic hybrid for peroxymonosulfate activation toward the degradation of organic pollutants

3D porous Co₃O₄/nitrogen-doped graphene aerogel (NGA) hybrid for heterogeneous activation of peroxymonosulfate (PMS) was prepared by feasible hydrothermal and freeze-drying methods. The morphology, crystal structure and chemical composition of the catalyst were investigated by scanning electron microscopy, X-ray diffractometer, X-ray photoelectron spectroscopy, Raman spectra and Fourier transform infrared spectroscopy. Co₃O₄/NGA at a high N doping level of 7.6% (in atomic percentage) exhibited excellent catalytic performance for acid orange 7 (AO7) degradation, with almost complete removal within 30 min. Moderate PMS content, higher temperature and lower solution pH conditions would facilitate the decomposition of AO7. The catalyst possesses excellent long-term stability and recycling performance with simple separation and post-treatment approaches. Kinetic model was developed to simulate the transformation of main active radical species and the AO7 oxidation profiles, considering effects of coexisting ions (Cl^- and HCO₃^-). Based on results of electron spin resonance, typical quenching tests and kinetic calculation, sulfate radicals play dominate role in AO7 degradation. Co₃O₄ nanocrystals and the new active sites created by nitrogen doping into graphene honeycomb network should synergistically contribute to the high degradation efficiency. This work has expanded the possibility of recyclable catalysts design for heterogeneous activation of PMS, with a dual catalytically active center and desirable stability.

Room-temperature synthesis of OMS-2 hybrids as highly efficient catalysts for pollutant degradation via peroxymonosulfate activation

Due to low cost and low toxicity, manganese oxides have been extensively explored to reduce organic pollutants in wastewater via peroxymonosulfate (PMS) activation; but the development of manganese-based catalysts with facile synthesis process at low temperatures and high efficiency is still of significant practical interest. In this paper, a simple room temperature method has been successfully developed to synthesize cryptomelane-type manganese octahedral molecular sieves (OMS-2) from KMnO₄ and MnSO₄ in the presence of carbon nanotubes (CNTs). The redox reaction between amorphous manganese oxide and CNTs results the decrease of manganese valences and the formation of OMS-2 phase at a low temperature of 25 °C. The changes of synthesis time, temperature and CNTs dosage altered the characteristics of the prepared materials. Compared with CNTs, OMS-2 and other manganese oxides hybrids, the synthesized catalysts demonstrated a remarkable efficiency for PMS activation to degrade organic dyes and a superior reusability during ten successive cycles. Sulfate radicals were formed as the active species in the system from the oxidation of low valent Mn species by PMS. This study not only provides a simple method to synthesize OMS-2 at room temperature, but also improves the understanding of PMS activation on manganese-based catalysts for pollutants degradation.