Microfluidics-enabled acceleration of Fenton oxidation for degradation of organic dyes with rod-like zero-valent iron nanoassemblies

Fluorescence Study of Pr3+ Doped CdS Nanoparticles and its Applications in Sensors and Detectors

Fluorescence spectra of Pr3+ doped CdS nanoparticles, synthesized by chemical precipitation method, have been recorded at room temperature. The synthesized particles are nearly spherical shaped and the grain size is decreased with the increase in Pr3+ concentration. The chemical identity of the nanoparticles was confirmed by EDAX spectrum, the absorption peaks was confirmed by FTIR spectrum and then the recorded values were compared with the CIE diagram. The oscillator strengths of the 4f ↔ 4I transitions are parameterized in terms of three phenomenological Judd-Ofelt intensity parameters Ωλ (λ = 2, 4 and 6). Using the fluorescence data and these Ωλ parameters, theoretical and experimental study of various radiative properties viz., spontaneous emission probability (A), radiative life time , fluorescence branching ratio and stimulated emission cross-section were evaluated. The values of these parameters indicate that 3P0→ 3H4 transition can be considered to be good laser transition in the visible colour region. Also, excitation with 493 nm, leads to similar blue regions. The synthesized Pr3+ doped CdS nanomaterials could be useful for sensing and detecting devices, particularly for temperature sensing measurement and bio-sensing detection.

A Radiative Chemical Process for the Methylene Blue Degradation by Natural Convective Nanofluid Flow over an Upright Cone

An upstraight cone with nonisothermal surface velocity, temperature, and concentration was investigated using a numerical solution approach to simulate MHD, MB dye, and various nanofluid flows. Numerical evaluation of the flow field equation was carried out using an excellent finite difference method after it has been converted into a dimensionless form. Different heat transfer occurrences were observed depending on temperature, velocity, and concentration when using several types of nanofluids (TiO, Ag, Cu, and Al₂O₃Z₃). The amount of MB dye that was degraded by the synthesized nanofluids under the influence of sunlight irradiation was 81.40 percent as a catalyst (carbon nanodots). The parametric analysis of various features of flow fields has been shown using graphs. It was observed that heat is generated from the cone during the sun light irradiation reaction, heat is transferred to MB dye containing nanofluids, and heat interacts with nanofluids and is involved in the chemical reaction with the assistance of electrons. As MB dye degrades in the absence of catalysts (carbon nanodots), it is only 52 percent effective. MB dye is degraded at 81.40 percent, then becomes stable, and takes 120 minutes to degrade in nanofluids containing MB dye with catalysts (carbon nanodots).

Sustainability insights into the synthesis of engineered nanomaterials - Problem formulation and considerations

Engineered nanomaterials (ENMs) have been introduced into the market for a wide range of applications. As per the literature review, the fabrication of new generations of ENMs is starting to comply with environmental, economic, and social criteria in addition to technical aspects to meet sustainability criteria. At this stage, identification of the appropriate criteria for the synthesis of ENMs is critical because the technologies already developed at the lab scales are being currently transferred to pilot and full scales. Hence, the development of scientific-based methodologies to identify, screen, and prioritize the involved criteria is highly necessary. In the present manuscript, a fuzzy-Delphi methodology is adopted to identify the main criteria and sub-criteria encompassing the sustainable fabrication of ENMs, and to explore the "degree of consensus" among the experts on the relative importance of the mentioned criteria. The "health and safety risks" respecting the equipment and the materials, solvent used, and availability of "green experts" were identified as the most critical criteria. Furthermore, although all the criteria were identified as being important, some criteria, such as "solvent" and "raw materials cost", raised a lower degree of consensus, indicating that various "degrees of uncertainties" still exist regarding the level of importance of the studied criteria.

Adsorption and photodegradation of reactive red 120 with nickel-iron-layered double hydroxide/biochar composites

Layered double hydroxide (LDH) materials were widely applied for adsorption and photodegradation of pollutants for wastewater treatment. New efficient LDH materials with adsorption and photodegradation abilities will be promising candidates for pollutants removal. Hence, a series of NiFe-LDH/biochar (NiFe/BC) were fabricated by the coprecipitation method for synergistic adsorption and photodegradation anionic dyes of reactive red 120 (RR120). The removal experiment showed that the addition of an appropriate amount of biochar into NiFe-LDH enhanced the adsorption capacity and its photocatalytic ability. The optimized NiFe/BC2 composite can remove 88.5 % of RR120 under visible light by adsorption and photocatalysis, which was much better than NiFe-LDH (63.3 %) and biochar (2.6 %). The photodegradation kinetic constant of the NiFe/BC2 composite was 3.1 and 104.8 times that of NiFe-LDH and BC. In addition, active species capture experiments and electron spin resonance (ESR) tests revealed the removal mechanisms of NiFe/BC composites for RR120 removal. This work affords a feasible strategy for preparing LDH-based photocatalyst with excellent adsorption and photocatalytic performance for wastewater treatment.

High-performance photocatalytic membranes for water purification in relation to environmental and operational parameters

Growing technologies, increasing population and environmental pollution lead to severe contamination of water and require advanced water treatment technologies. These aspects lead to the need to purify water with advanced smart materials. This paper reviews the recent advances (during the last 5 years) in photocatalytic composite membranes used for water treatment. For this purpose, the authors have reviewed the main materials used in the development of (photocatalytic membranes) PMs, environmental and operational factors affecting the performance of photocatalytic membranes, and the latest developments and applications of PMs in water purifications. The composite photocatalytic membranes show good performance in the removal and degradation of pollutants from water.

Advanced oxidation processes in microreactors for water and wastewater treatment: Development, challenges, and opportunities

The miniaturization of reaction processes by microreactors offers many significant advantages over the use of larger, conventional reactors. Microreactors' interior structures exhibit comparatively higher surface area-to-volume ratios, which reduce reactant diffusion distances, enable faster and more efficient heat and mass transfer, and better control over process conditions. These advantages can be exploited to significantly enhance the performance of advanced oxidation processes (AOPs) commonly used for the removal of water pollutants. This comprehensive review of the rapidly emerging area of environmental microfluidics describes recent advances in the development and application of microreactors to AOPs for water and wastewater treatment. Consideration is given to the hydrodynamic properties, construction materials, fabrication techniques, designs, process features, and upscaling of microreactors used for AOPs. The use of microreactors for various AOP types, including photocatalytic, electrochemical, Fenton, ozonation, and plasma-phase processes, showcases how microfluidic technology enhances mass transfer, improves treatment efficiency, and decreases the consumption of energy and chemicals. Despite significant advancements of microreactor technology, organic pollutant degradation mechanisms that operate during microscale AOPs remain poorly understood. Moreover, limited throughput capacity of microreactor systems significantly restrains their industrial-scale applicability. Since large microreactor-inspired AOP systems are needed to meet the high-throughput requirements of the water treatment sector, scale-up strategies and recommendations are suggested as priority research opportunities. While microstructured reactor technology remains in an early stage of development, this work offers valuable insight for future research and development of AOPs in microreactors for environmental purposes.

Plasmonic nanosensors for point-of-care biomarker detection

Advancement of materials along with their fascinating properties play increasingly important role in facilitating the rapid progress in medicine. An excellent example is the recent development of biosensors based on nanomaterials that induce surface plasmon effect for screening biomarkers of various diseases ranging from cancer to Covid-19. The recent global pandemic re-confirmed the trend of real-time diagnosis in public health to be in point-of-care (POC) settings that can screen interested biomarkers at home, or literally anywhere else, at any time. Plasmonic biosensors, thanks to its versatile designs and extraordinary sensitivities, can be scaled into small and portable devices for POC diagnostic tools. In the meantime, efforts are being made to speed up, simplify and lower the cost of the signal readout process including converting the conventional heavy laboratory instruments into lightweight handheld devices. This article reviews the recent progress on the design of plasmonic nanomaterial-based biosensors for biomarker detection with a perspective of POC applications. After briefly introducing the plasmonic detection working mechanisms and devices, the selected highlights in the field focusing on the technology's design including nanomaterials development, structure assembly, and target applications are presented and analyzed. In parallel, discussions on the sensor's current or potential applicability in POC diagnosis are provided. Finally, challenges and opportunities in plasmonic biosensor for biomarker detection, such as the current Covid-19 pandemic and its testing using plasmonic biosensor and incorporation of machine learning algorithms are discussed.

Preparation, characterization, and applications of Fe-based catalysts in advanced oxidation processes for organics removal: A review

Fe-based catalysts as low-cost, high-efficiency, and non-toxic materials display superior catalytic performances in activating hydrogen peroxide, persulfate (PS), peracetic acid (PAA), percarbonate (PC), and ozone to degrade organic contaminants in aqueous solutions. They mainly include ferrous salts, zero-valent iron, iron-metal composites, iron sulfides, iron oxyhydroxides, iron oxides, and supported iron-based catalysts, which have been widely applied in advanced oxidation processes (AOPs). However, there is lack of a comprehensive review systematically reporting their synthesis, characterization, and applications. It is imperative to evaluate the catalytic performances of various Fe-based catalysts in diverse AOPs systems and reveal the activation mechanisms of different oxidants by Fe-based catalysts. This work detailedly summarizes the synthesis methods and characterization technologies of Fe-based catalysts. This paper critically evaluates the catalytic performances of Fe-based catalysts in diverse AOPs systems. The effects of solution pH, reaction temperature, coexisting ions, oxidant concentration, catalyst dosage, and external energy on the degradation of organic contaminants in the Fe-based catalyst/oxidant systems and the stability of Fe-based catalysts are also discussed. The activation mechanisms of various oxidants and the degradation pathways of organic contaminants in the Fe-based catalyst/oxidant systems are revealed by a series of novel detection methods and characterization technologies. Future research prospects on the potential preparation means of Fe-based catalysts, practical applications, assistive technologies, and impact in AOPs are proposed.

Adsorption Behavior of Crystal Violet and Congo Red Dyes on Heat-Treated Brazilian Palygorskite: Kinetic, Isothermal and Thermodynamic Studies

The effect of heat treatment on the adsorptive capacity of a Brazilian palygorskite to remove the dyes crystal violet (CV) and congo red (CR) was investigated. The natural palygorskite was calcined at different temperatures (300, 500 and 700 °C) for 4 h. Changes in the palygorskite structure were evaluated using X-ray diffraction, X-ray fluorescence, thermogravimetric and differential thermal analysis, N₂ adsorption/desorption and Fourier transform infrared spectroscopy. The adsorption efficiency of CV and CR was investigated through the effect of initial concentration, contact time, temperature, pH and dosage of adsorbent. The calcination increased the adsorption capacity of palygorskite, and the greatest adsorption capacity of CV and CR dyes occurred in the sample calcined at 700 °C (Pal-700T). The natural and calcined samples at 300 and 500 °C followed the Freundlich isothermal model, while the Pal-700T followed the Langmuir isothermal model. Adsorption kinetics results were well described by the Elovich model. Pal-700T showed better adsorption performance at basic pH, with removal greater than 98%, for both dyes. Pal-700T proved to be a great candidate for removing cationic and anionic dyes present in water.

Fabrication of a Nanoporous Silica Hydrogel by Cross-Linking of SiO2-H3BO3-Hexadecyltrimethoxysilane for Excellent Adsorption of Azo Dyes from Wastewater

This study reports a novel cross-linking approach to fabricate the hydrothermally neutralized silica hydrogel of SiO₂-H₃BO₃-hexadecyltrimethoxysilane by grafting alkylsilane groups onto the nanoporous silica. The synthesized silica hydrogel possessed a large specific surface area of 51.3 m²g^-1 and showed excellent dye adsorption capability of cationic dyes in neutral (pH 7) and alkaline (pH 9) medium from wastewater. The colloidal electrokinetic potential analysis revealed that the outstanding adsorption efficiency of cationic dyes over anionic dyes strongly relies on the surface charge of the hydrogels. Moreover, the hydrophobic interactions between the dye molecules and the hydrogels were studied, and it was found that the dye adsorption performance can be tuned by altering the concentration of hydrophobic reagents of the hydrogel. The dye adsorption mechanism was established, and the kinetic study suggested that the adsorption is a pseudo-second-order reaction. Adsorption isotherms at various equilibrium conditions fitted well with the Langmuir isotherm. Therefore, this strongly supports the promising and practical application of the prepared silica hydrogel. The recyclability of the hydrogel was studied, and it showed 90% adsorption efficiency by the regenerated gel up to 6 cycles, which has a high potential in wastewater treatment.

Amine-rich quartz nanoparticles for Cu(II) chelation and their application as an efficient catalyst for oxidative degradation of Rhodamine B dye

The study describes the loading of the quartz SiO₂ nanoparticles (NPs) with (3-aminopropyl)triethoxysilane (APTES) linker with simultaneous lengthening of the linker through the terminal amine group by glutaraldehyde (GA). The reactive polyethylenimine (PEI) was introduced to the surface to increase the ability to capture Cu(II) ions. The composite got the abbreviation SiO₂/PEI-Cu(II). The Cu(II) ions were the active center with a peroxo-complex activation state. The composite characterization included scanning electron microscopy (SEM), transmission electron microscopy (TEM), electron-dispersive X-ray analysis (EDX), Fourier transform infrared spectroscopy (FT-IR), X-ray powder diffraction (XRD), thermogravimetric analysis (TGA), and Brunauer-Emmett-Teller (BET) surface analyzer. The kinetics of the oxidative degradation of Rhodamine B (RhB) dye obeyed the pseudo-first order under flooding conditions. The reaction parameters including the catalyst dose, solution pH, initial concentration of reactants, and temperature got some attention. The obtained results showed that more than 91.7 ± 1% of RhB dye was degraded to CO₂, NH₄⁺, NO₃^-, H₂O, and some inorganic acids after 30 min as confirmed by gas chromatography mass spectrometry and total organic carbon (TOC) measurements. Also, GC-MS spectra for water samples drawn from the reaction in successive periods had suggested a conceivable degradation pathway for RhB by hydroxyl radicals. Degradation starts with de-alkylation then carboxyphenyl removal followed by two successive ring-opening stages. Both the effects of the catalyst recycling and treated water reusability on the reaction rate were studied. The catalyst provided noticeable stability over three consecutive cycles.

Cyan color-emitting nitrogen-functionalized carbon nanodots (NFCNDs) from Indigofera tinctoria and their catalytic reduction of organic dyes and fluorescent ink applications

The present study reports the synthesis of nitrogen-functionalized carbon nanodots (NFCNDs) by a low-cost hydrothermal method using the leaf extract of Indigofera tinctoria as a novel carbon precursor.

Microfluidic High-Throughput Platforms for Discovery of Novel Materials

High-throughput screening is a potent technique to accelerate the discovery and development of new materials. By performing massive synthesis and characterization processes in parallel, it can rapidly discover materials with desired components, structures and functions. Among the various approaches for high-throughput screening, microfluidic platforms have attracted increasing attention. Compared with many current strategies that are generally based on robotic dispensers and automatic microplates, microfluidic platforms can significantly increase the throughput and reduce the consumption of reagents by several orders of magnitude. In this review, we first introduce current advances of the two types of microfluidic high-throughput platforms based on microarrays and microdroplets, respectively. Then the utilization of these platforms for screening different types of materials, including inorganic metals, metal alloys and organic polymers are described in detail. Finally, the challenges and opportunities in this promising field are critically discussed.

Direct Synthesis of Magnetic CoFe2O4 Nanoparticles as Recyclable Photo-Fenton Catalysts for Removing Organic Dyes

Herein, CoFe₂O₄ nanoparticles were directly synthesized through a solution combustion method using ferric nitrate, cobalt nitrate, and glycine as raw materials. The effects of glycine on the phase composition and magnetic properties of the CoFe₂O₄ products were investigated. When the fuel/ferric nitrate ratio was 0.8, the obtained product was pure CoFe₂O₄ with an average particle size of 25 nm. Furthermore, the saturation magnetization is 77.3 emu/g, which is about 95.7% that of CoFe₂O₄ bulk materials at room temperature and good for recycling. The photo-Fenton catalytic properties of CoFe₂O₄ were investigated for assessing its efficacy in removing dyes. It could degrade the 20 ppm MB in 75 min. To improve the photo-Fenton catalytic performance, NH₄HCO₃ and glucose were employed as additives. Due to the pores formed by NH₄HCO₃ and glucose, the G-CoFe₂O₄ and N-CoFe₂O₄ could degrade the 20 ppm MB in 40 and 25 min, respectively. The results indicated that these additives can effectively improve the catalytic activity of CoFe₂O₄. The modified CoFe₂O₄ is a promising alternative recyclable photo-Fenton catalyst for removing organic dyes.

Integrated Membrane-Electrocoagulation System for Removal of Celestine Blue Dyes in Wastewater

The textile industry provides for the needs of people especially in apparel and household items. The industry also discharges dye-containing wastewater that is typically challenging to treat. Despite the application of the biological and chemical treatments for the treatment of textile wastewater, these methods have their own drawbacks such as non-environment friendly, high cost and energy intensive. This research investigates the efficiency of the celestine blue dye removal from simulated textile wastewater by electrocoagulation (EC) method using iron (Fe) electrodes through an electrolytic cell, integrated with nylon 6,6 nanofiber (NF) membrane filtration for the separation of the flocculants from aqueous water. Based on the results, the integrated system achieves a high dye removal efficiency of 79.4%, by using 1000 ppm of sodium chloride as the electrolyte and 2 V of voltage at a constant pH of 7 and 10 ppm celestine blue dye solution, compared to the standalone EC method in which only 43.2% removal was achieved. Atomic absorption spectroscopy analysis was used to identify the traces of iron in the residual EC solution confirming the absence of iron. The EC-integrated membrane system thus shows superior performance compared to the conventional method whereby an additional 10–30% of dye was removed at 1 V and 2 V using similar energy consumptions.

Microfluidics for ZnO micro-/nanomaterials development: rational design, controllable synthesis, and on-chip bioapplications

Zinc oxide (ZnO) materials hold great promise in diverse applications due to their attractive physicochemical features. Recent years, especially the last decade, have witnessed considerable progress toward rational design and bioapplications of multiscale ZnO materials through microfluidic techniques. Design of a microfluidic device that allows for precise control over reaction conditions could not only yield ZnO particles with a fast production rate and high quality, but also permit downstream applications with desirable and superior performance. This review summarizes microfluidic approaches for the synthesis and applications of ZnO micro-/nanomaterials. In particular, we discuss the recent achievement of using microfluidic reactors in the controllable synthesis of ZnO structures (wire, rod, sphere, flower, sheet, flake, spindle, and ellipsoid), and highlight the unprecedented opportunities for applying them in biosensing, biological separation, and molecular catalysis applications through microfluidic chips. Finally, major challenges and potential opportunities are explored to guide future studies in this area.