Remediation of malachite green in wastewater by ZIF-8@Fe/Ni nanoparticles based on adsorption and reduction

Anisotropic Chitosan-nanocellulose/Zeolite imidazolate frameworks-8 aerogel for sustainable dye removal

Assembling microscopic metal-organic frameworks into macroscopic polymeric scaffolds to develop highly renewable materials has been a promising yet challenging area of research. Herein, chitosan (CS) blended with nano-cellulose (NC) was unidirectionally transformed into an aerogel with oriented macropores and then biomineralized with zeolite imidazolate frameworks-8 (ZIF-8) to form a hierarchical structured chitosan-nanocellulose/zeolite imidazolate frameworks-8 (CS-NC-ZIF-8) hybrid aerogel. Incorporating ZIF-8 significantly increases the versatility and mechanical strength with a Young's modulus of 14.18 MPa of the CS-NC aerogel. The incorporation of ZIF-8 into the aerogel not only enhances its adsorption capacity for methylene blue, rhodamine B, acid fuchsin, and methyl orange, but also facilitates the generation of electrons from water that can be transferred to degrade > 90 % of malachite green within 90 min in each catalytic cycle, and this capability was maintained for at least 10 consecutive cycles. Remarkably, the hybrid aerogel was highly renewable after the adsorption of cationic dyes and catalytic removal of malachite green. With its facile production process, high removal efficiency, affordable and green nature, and excellent regeneration feasibility, the CS-NC-ZIF-8 aerogel stands as a promising solution for addressing challenges associated with dye-contaminated water treatment.

Study on the Performance of Coal Gangue-Loaded Hydroxyapatite (CG@HAP) for the Adsorption of Malachite Green

In response to the issues of dye wastewater pollution and coal gangue accumulation, a novel adsorbent, coal gangue-loaded hydroxyapatite (CG@HAP) was prepared using coal gangue as the raw material for the adsorption of malachite green dye wastewater. Based on batch experiments, combined with adsorption kinetics and isotherm models, as well as XRF, FTIR, XRD, and SEM analysis, the characteristics of CG@HAP in adsorbing malachite green were investigated. The results show that CG@HAP can be prepared by adding 150 mL of 0.15 mol/L (NH4)2HPO4 solution and 150 mL of 0.25 mol/L CaCl2 solution to 10 g coal gangue under the condition of pH = 10, allowing it to stand at room temperature for 24 h. When the dosage of CG@HAP was 0.10 g and the adsorption time was 180 min, the adsorption removal rate and adsorption capacity of CG@HAP for 400 mg/L malachite green reached 92.62% and 370.49 mg/g, respectively. The adsorption of malachite green by CG@HAP followed the pseudo-second-order kinetic model and the Langmuir isotherm model. The adsorption of malachite green by CG@HAP was primarily governed by chemical reactions, adhering to the Langmuir monolayer adsorption principle. The maximum adsorption capacity of CG@HAP for malachite green was 386 mg/g. CG@HAP exhibited sustained and efficient dynamic adsorption of malachite green, maintaining a removal rate between 83.52% and 99.96%. CG@HAP proved to be an efficient adsorbent for malachite green, with great potential for application.

Carboxymethyl cellulose assisted morphology controlled synthesis of Mn3O4 nanostructures for adsorptive removal of malachite green from water

The physicochemical properties of manganese oxides and their different applications mainly depend upon their crystallite size, morphology, phase structure, and surface properties, which are again dependent on the preparation methods. So, a simple, cost-effective, and versatile synthesis method for such materials is highly desirable. Intending to accomplish this, herein we report the synthesis of Mn3O4 nanostructures by alkaline hydrolysis of the corresponding metal ions in an aqueous medium. The addition of a biodegradable polymer, sodium salt of carboxymethyl cellulose (Na-CMC) assisted the development of specific morphology, which is tunable by varying the concentration of the biopolymer. The spectroscopic, microscopic, and diffractometric analyses of the synthesized Mn3O4 nanostructures confirm that this particular simple technique is very effective in controlling the morphology of the formed nanostructures. These Mn3O4 nanostructures exhibit excellent adsorption capacity in the removal of malachite green (MG) from its aqueous solution under ambient conditions. The adsorption process is exothermic following pseudo-second-order kinetics with a maximum dye adsorption capacity of 489.68 mg g-1 according to the Sips isotherm model. The Mn3O4 nanostructures can be reused for up to five cycles of dye adsorption without significant loss of their adsorption performance.

rGO/ZIF-8 Aerogel for Effective Removal of Malachite Green from Wastewater

In this study, dopamine-modified graphene aerogel (DGA) is synthesized through a one-step hydrothermal method using graphene oxide as the precursor and dopamine as the reducing agent. Subsequently, in situ immersion synthesis is conducted to obtain ZIF-8 loaded on a dopamine-modified graphene aerogel skeleton (ZDGA), featuring a regular honeycomb interconnected mesoporosity and a high specific surface area of 532.8 m2/g. The synthesized ZDGA exhibited exceptional adsorption performance for the cationic dye malachite green. At room temperature, ZDGA achieved an impressive equilibrium adsorption capacity of 6578.34 mg/g. The adsorption process followed pseudo-secondary kinetics and adhered to the Langmuir model, indicating chemically dominated adsorption on a monomolecular layer. Intraparticle diffusion was the primary rate determinant, with π-π stacking, electrostatic adsorption, hydrogen bonding, and Lewis acid-base interactions serving as the key driving forces. It has an ideal specific surface area and good cycling performance, which highlights its potential application in dye wastewater treatment.

Progressive Insights into Metal-Organic Frameworks and Metal-Organic Framework-Membrane Composite Systems for Wastewater Management

The sustainable management of wastewater through recycling and utilization stands as a pressing concern in the trajectory of societal advancement. Prioritizing the elimination of diverse organic contaminants is paramount in wastewater treatment, garnering significant attention from researchers worldwide. Emerging metal-organic framework materials (MOFs), bridging organic and inorganic attributes, have surfaced as novel adsorbents, showcasing pivotal potential in wastewater remediation. Nevertheless, challenges like limited water stability, elevated dissolution rates, and inadequate hydrophobicity persist in the context of wastewater treatment. To enhance the performance of MOFs, they can be modified through chemical or physical methods, and combined with membrane materials as additives to create membrane composite materials. These membrane composites, derived from MOFs, exhibit remarkable characteristics including enhanced porosity, adjustable pore dimensions, superior permeability, optimal conductivity, and robust water stability. Their ability to effectively sequester organic compounds has spurred significant research in this field. This paper introduces methods for enhancing the performance of MOFs and explores their potential applications in water treatment. It delves into the detailed design, synthesis strategies, and fabrication of composite membranes using MOFs. Furthermore, it focuses on the application prospects, challenges, and opportunities associated with MOF composite membranes in water treatment.

Bionanocomposite based on immobilization of Burkholderia cepacian on GO/MOF and its removal of malachite green from river water

Bio-nanocomposites have attracted increasing research attention because they are able to integrate bio- and nano-related functions, and subsequently demonstrate potentially beneficial environmental applications. Here, a functional bionanomaterial based on Burkholderia cepacian (FZ) immobilized on GO/ZIF-8 was developed and used to remove malachite green (MG), with functions based on both biodegradation and adsorption. XRD and FTIR results showed that in situ production of GO/ZIF-8 by combining Zn2+ in ZIF-8 with the carboxyl group on the GO surface, led to FZ immobilized in GO/ZIF-8 through covalent bonding. Zeta analysis showed that the surface of FZ and GO/ZIF-8 had different charges under pH = 9.12, suggesting immobilization also occurred via electrostatic action. BET results confirmed that the specific surface area of GO/ZIF-8 was much larger than that of GO and ZIF-8, but the reduced specific surface area of FZ@GO/ZIF-8 could be due to FZ loading on its surface. The efficiency of FZ@GO/ZIF-8 in the removal of MG reached 99% and furthermore retained good stability after five cycles. The efficiency in removing multiple ions in river water reached more than 80%, which is evidence strongly suggesting that FZ@GO/ZIF-8 is an environmental bionanomaterial with effective application potential.

Efficient removal of cationic dye using ZIF-8 based sodium alginate composite beads: Performance evaluation in batch and column systems

The environmental and health risks associated with dye contamination in water sources are alarming. Recently, researchers have been focusing on developing an innovative and susceptible solution using composite beads that effectively combat this issue. In this paper, beads were synthesized using a sodium alginate (SA) and zeolitic imidazolate framework-8 (ZIF-8) through a simple dipping process. Several characterization tests were performed including XRD, FTIR, BET, TGA, and SEM-EDX. The SEM images confirmed that SA effectively coated the cubical structure of the ZIF-8, ensuring optimal performance. The efficiency of the resulting SA@ZIF-8 composite beads was tested on both synthetic malachite green dye and real industrial wastewater samples using batch and fixed bed column reactors. The findings revealed that maximum adsorption of 95.5% was achieved at pH 6 in 120 min of reaction time. FTIR and SEM analysis also confirmed the adsorption of MG dye onto the beads. The Freundlich isotherm model (R2 > 0.99) has a better fit than the Langmuir (R2 > 0.96) for describing the adsorption process. The PSO model predicted the kinetics of the system, whereas the intraparticle diffusion study supported the system's mechanistic analysis. Furthermore, the study also investigated the efficacy of the beads in treating real wastewater effluent samples collected from the dye industry. Overall, using sodium alginate-coated ZIF-8 beads was found to have many advantages over powdered ZIF-8, including higher selectivity, stability, reusability, and practicality, making them a promising alternative for adsorption applications. Therefore, these composite beads have the potential for the removal of the dye from wastewater, which could be widely applied in various industries.

Effective removal of malachite green from local dyeing wastewater using zinc-tungstate based materials

The frequent use of an industrial dye such as malachite green (MG) has caused major water body deterioration and is one of the most pressing global challenges, demanding effective treatment techniques. To solve these issues, a simplistic method was developed to synthesize zinc-tungstate (ZnWO4) nanoparticles and also dope the surface matrix of the ZnWO4 nanoparticles using nonmetals of boron (B), carbon (C), and nitrogen (N) at different ratios for enhanced MG removal from wastewater. The prepared nanomaterials were characterized by different methods for crystal structure composition, surface properties, surface morphology, microstructures, functional groups, and elemental oxidation states. The BET analysis revealed a mesoporous structure with surface areas of 30.740 m2/g for ZnWO4, 38.513 m2/g for ZnWO4@BCN, 37.368 m2/g for ZnWO4@BCN/B, 39.325 m2/g for ZnWO4@BCN/C, and 45.436 m2/g for ZnWO4@BCN/N nanocomposites. The best removal of MG was accomplished at pH (8), contact period (50 min), nanoadsorbent dose (0.8 g/L), initial MG concentration (20 mg/L), and temperature (303 K). The maximum adsorption capacities of ZnWO4 and ZnWO4@BCN/N towards MG were 218.645 and 251.758 mg/g, respectively. At equilibrium, the Freundlich isotherm and pseudo-second-order kinetic models were the best fits for the experimental data of MG adsorption on both nanoadsorbents. After eight cycles of adsorption and desorption, both ZnWO4 and ZnWO4@BCN/N were found to be good at removing MG, with efficiencies of 71.00 and 74.20%, respectively. Thermodynamic investigations further validated the spontaneity and endothermic nature of the adsorption process. All study findings confirm the nanoadsorbents exceptional capability and economic feasibility for removing MG dye.

Versatile CO2-responsive Sponges Decorated with ZIF-8 for Bidirectional Separation of Oil/Water and Controllable Removal of Dyes

The complex wastewater containing water-soluble dyes and water-insoluble oils has given rise to significant environmental concerns that demand urgent remediation. Herein, a novel "smart" multifunctional sponge (ZIF-8@PMS) stepwise decorated with ZIF-8 nanoparticles and CO2-responsive copolymer (poly(2-(diethylamino) ethyl methacrylate-co-3-(trimethoxysilyl)propyl acrylate-co-stearyl methacrylate) was successfully prepared for CO2 controllable oil/water separation and dyes removal. The results revealed that the sponge coated with CO2-responsive copolymer for three cycles (ZIF-8@PMS-3) exhibited optimal comprehensive properties. The ZIF-8@PMS-3 had excellent compressive-resilient characteristics and chemical stability. As expected, it displayed tunable wettability and charged state under the regulation of CO2. Based on these features, ZIF-8@PMS-3 presented highly efficient removal of oil and dyes, even for the dye-containing oil/water emulsions, via a synergistic combination of adsorption and separation methods. The adsorption capacity for oil and various organic solvents ranged from 21.3 to 50 g g-1. The maximum adsorption capacities toward anionic dyes: methyl orange with 1205.89 mg g-1 and methyl blue with 880.00 mg g-1 in the presence of CO2 through electrostatic interaction. In the absence of CO2, it achieved maximum adsorption capacities for cationic dyes, including malachite green with 1246.15 mg g-1 and rhodamine B with 203 mg g-1, primarily driven by π-π interactions. According to distinct adsorption mechanisms, ZIF-8@PMS-3 could selectively adsorb either anionic or cationic dyes by exploiting CO2 as a trigger. Furthermore, the separation efficiencies for both types of oil/water emulsions surpassed 99.9%, with respective fluxes of 1566.99 L m-2 h-1 (water-in-oil emulsion) and 310.37 L m-2 h-1 (oil-in-water emulsion). Additionally, the as-prepared sponges exhibited remarkable antibacterial properties and exceptional recyclability. Therefore, the ZIF-8@PMS-3 holds substantial promise for potential applications in practical industrial wastewater treatment.

New insights into engineering the core size and carbon shell thickness of Co@C core-shell catalysts for efficient and stable Fenton-like catalysis

Herein, we engineered the cobalt core size and carbon shell thickness of Co@C by molten salt electrolysis (MSE) to investigate the enhanced essence of decreasing core size as well as the shell thickness dependence-mediated transition of catalytic mechanisms. We found that the reaction activation energy (RAE) of Co@C/peroxymonosulfate (PMS) systems was intimately dependent on the core sizes for sulfamethoxazole (SMX) degradation. The smaller core size of 26 nm provided a lower RAE of 13.39 kJ mol^-1. In addition, increasing carbon shell thicknesses of Co@C altered the catalytic mechanisms from a radical pathway of SO₄^•- and •OH to to a non-radical pathway of ¹O₂ and electron-transfer process (ETP), which were verified by experimental results and density functional theory (DFT) calculations. Interestingly, increasing carbon shell thicknesses promoted the charge transfer between Co metal slab and carbon shell, increased the adsorption energy of PMS molecule on the Co@C slab, and decreased the length of OO, which favoured the occurrence of non-free radical processes.

Fabrication of nano-biocomposite for the removal of Eriochrome Black T and malachite green from aqueous solution: isotherm and kinetic studies

The increasing generation of toxic dye wastewater from various enterprises continues to be a serious public health issue and happens to be of environmental concern, posing a significant challenge to existing conventional water treatment facilities. Malachite green (MG) and Eriochrome Black T (EBT) are extremely hazardous and carcinogenic substances; hence it is crucial to remove them from water bodies. A well-known cleaner, more economical, and environmentally friendly treatment method is adsorption. The kind of adsorbent material employed determines how well the treatment procedure works. A physiologically compatible nanocomposite adsorbent (HAP@CT@MNP) was fabricated from laboratory synthesized hydroxyapatite (HAP) and magnetite (MNP) for its application in the wastewater remediation process. The ability of the fabricated nanocomposite to remove the harmful dyes EBT and MG from a simulated wastewater was evaluated. The impact of operational parameters including pH, adsorbate concentration, adsorbent dose, contact time, and temperature was examined to gauge the maximum adsorption capacity of the developed nanocomposite. The optimum pH for the eradication of EBT and MG were found to be 3 and 7.4, respectively. The maximum capacity evaluated was 222 mg/g and 500 mg/g at room temperature and at contact time of 50 and 40 min respectively. The binding of either EBT or MG followed the monolayer Langmuir model and kinetic studies revealed the suitability of pseudo-second-order model. Studies using spectroscopy and isotherm modeling showed that the main mechanism controlling the adsorption of EBT and MG onto HAP@CT@MNP is physisorption. The efficacy of the adsorbent to be reused with 8% loss in its efficiency reveals the economic viability of HAP@CT@MNP. The current work showed that a biocompatible nanocomposite could be successfully fabricated and used as an enhanced adsorbent for the quick and effective removal of the toxic dyes EBT and MG from wastewater.

A portable architectonics of Al/carbon nitride/metal-organic frameworks anchored Ag nanoparticles for SERS detection and photocatalytic degradation of fungicide

In recent years, it is urgent to develop bi-functional materials for highly sensitive SERS detection and photocatalytic degradation of contaminants in water of fish pond. Herein, using 5-mercapto-1-methyltetrazole as the ligand, the tree-trunk like zeolitic imidazolate framework (ZIF-8) is induced and in-situ grown on the surface of aluminum/flower carbon nitride (Al/f-C₃N₄). Then, AgNPs are tightly anchored in ZIF-8 of Al/f-C₃N₄/ZIF-8 by strong Ag-N and Ag-S bonds, and a portable architecture of Al/f-C₃N₄/ZIF-8/Ag is successfully prepared. Results indicate that the Al/f-C₃N₄/ZIF-8/Ag architecture exhibits excellent SERS activity and the detection limit can as low as 2.15 × 10^-11 mol⋅L^-1 for crystal violet (CV, a typical fungicide). Also, the Al/f-C₃N₄/ZIF-8/Ag substrate presents good photocatalytic activity for CV molecule, and the degradation efficiency reaches 98.58% after illumination for 90 min. This is mainly due to the good adsorption capacity of ZIF-8 which can enrich more CV molecules and pull them to "hot spots" generated by Ag in Al/f-C₃N₄/ZIF-8/Ag, and thus SERS response are enhanced significantly. Besides, the strong synergistic effect of f-C₃N₄, ZIF-8 and AgNPs is also important which facilitates the separation of photogenerated electrons and holes. Thus, the designed portable and bi-functional substrate could be used as a potential material for the detection and removal of CV in practical application.

Fe, Ni-modified ZIF-8 as a tensive precursor to derive N-doped carbon as Na and Li-ion batteries anodes

Carbon materials derived from metal-organic frameworks have attracted increasing attention as anodes for energy storage. In this study, Fe, Ni-doped ZIF-8 is carbonized at high temperature to obtain bimetallic Fe and Ni modified tension -relaxed carbon (FeNi@trC). Fe and Ni have opposite structural modification effects when the metal ions are doped into the ZIF-8 dodecahedron. The obtained carbon material maintains the regular dodecahedron morphology, which means the relaxation of tension and strong thermal stability during annealing. Moreover, the presence of nickel enhances the carbonization degree and electrochemical stability of FeNi@trC, while the calcination of the tensive ZIF-8 precursor offers more defect sites. The discharge capacities of FeNi@trC materials are stable at 182.9 mAh·g^-1and 567.9 mAh·g^-1for sodium-ion batterie (SIB) and lithium-ion batterie (LIB) at 0.05 A·g^-1. Compared with the current density of 0.05 A·g^-1, the discharge capacity of SIB and LIB attenuates by 29.4% and 55.9% at 1 A·g^-1, respectively, and the FeNi@trC shows good performance stability in the following cycles.

Waste Valorization of a Recycled ZnCoFe Mixed Metal Oxide/Ceftriaxone Waste Layered Nanoadsorbent for Further Dye Removal

Waste valorization of spent wastewater nanoadsorbents is a promising technique to support the circular economy strategies. The terrible rise of heavy metal pollution in the environment is considered a serious threat to the terrestrial and aquatic environment. This led to the necessity of developing cost-effective, operation-convenient, and recyclable adsorbents. ZnCoFe mixed metal oxide (MMO) was synthesized using co-precipitation. The sample was characterized using X-ray powder diffraction, Fourier transform infrared spectroscopy, and scanning electron microscopy. Factors affecting the adsorption process such as pH, the dose of adsorbent, and time were investigated. ZnCoFe MMO showed the maximum adsorption capacity of 118.45 mg/g for ceftriaxone sodium. The spent MMO was recycled as an adsorbent for malachite green (MG) removal. Interestingly, the spent adsorbent showed 94% removal percent for MG as compared to the fresh MMO (90%). The kinetic investigation of the adsorption process was performed and discussed. In addition, ZnCoFe MMO was tested as an antimicrobial agent. The proposed approach opens up a new avenue for recycling wastes after adsorption into value-added materials for utilization in adsorbent production with excellent performance as antimicrobial agents.

Treatment of fluorinated wastewater with chitosan modified activated sludge lysis ash

Preparation of a novel environmentally friendly and cost-effective composite adsorbent for fluoride removal is presented in this work. An activated sludge lysis ash/chitosan (ASLA/C) composite adsorbent was synthesised using an in situ coprecipitation method, and the removal effect of the material was analysed by static adsorption, isothermal adsorption and kinetic adsorption tests. Langmuir model could better describe the adsorption process and the adsorption was in accordance with the kinetic equation of the pseudo-second-order kinetics reaction. The values of adsorption thermodynamic and kinetic parameters were indicated that the adsorption of fluoride ions is a spontaneous, heat-absorbing entropic process, and the reaction was carried out by a combination of mechanisms, such as electrostatic adsorption, ion exchange, surface complexation and hydrogen bonding. The experimental results indicated that ASLA/C can be used as a cheap and readily available alternative efficient adsorbent where the maximum fluorinate absorption was observed with 7.714 mg g^-1, while solving the problem of waste from activated sludge lysis disposal and realizing the environmental benefits of waste.

Multiple cobalt active sites evenly embedded in mesoporous carbon nanospheres derived from a polymer-metal-organic framework: efficient removal and photodegradation of malachite green

A series of robust photocatalysts of mesoporous carbon nanospheres embedded with multiple cobalt active sites (Co/Co x O y @mC) have been constructed for efficient removal and photodegradation of malachite green (MG). Here, a cobalt-based polymeric-metal-organic framework (polyMOF(Co)) was constructed by using a polyether ligand containing 1,4-benzenedicarboxylic acid units. Afterward, polyMOF(Co) was calcined into a series of Co/Co x O y @mC hybrids at diverse high temperatures (400, 600, and 800 °C) under a N2 atmosphere. Therefore, Co coordination centers were transformed into various active sites such as Co, CoO, and Co3O4, which were embedded within the mesoporous carbon network derived from the polymeric skeleton. Considering the even distribution of Co-related active species and high porosity inherited from polyMOF(Co), the constructed Co/Co x O y @mC hybrid obtained at 600 °C illustrated higher removal ability (79%) with a maximum adsorption capacity of 314 mg g-1 within 120 min and better photodegradation performance (degradation rate of 95%) toward MG than those of the other photocatalysts obtained at 400 and 800 °C. Moreover, the possible photocatalytic reaction mechanisms, including the transfer behavior of charge carriers, generation of reactive species, and intermediate degradation of products, were provided. The present work showed an alternative strategy for the feasible and efficient preparation of photocatalysts based on MOFs.

Adsorption and fenton-like oxidation of ofloxacin in wastewater using hybrid MOF bimetallic Fe/Ni nanoparticles

Since ofloxacin (OFX) is one of many common antibiotics, which effluxes into aquatic environment in relatively high concentration, it has become of significant environmental concern due to the potential for increased antibiotic resistance. In this study, an innovative functional Fe/Ni@ZIF-8 composite was successfully used for the Fenton-like oxidation of OFX, with a OFX removal efficiency >98% under optimal conditions. FTIR analysis confirmed that OFX removal occurred via adsorption to Fe/Ni@ZIF-8 by a combination of π-π bond intercalation and electrostatic interaction, while XPS revealed that the Fe/Ni NPs in Fe/Ni@ZIF-8 were also involved in oxidation. Furthermore, LC-MS analysis identified the presence of several OFX degradation products post exposure, which indicted that Fe/Ni NPs in Fe/Ni@ZIF-8 reacted with H₂O₂ to form •OH, leading to Fenton-like oxidation of OFX. Thus overall, OFX removal by Fe/Ni@ZIF-8 involved both adsorption to ZIF-8 and Fenton-like oxidation by Fe/Ni NPs. A synergistic mechanism for OFX removal by Fe/Ni@ZIF-8 was thus proposed. The removal efficiency of the synthesized catalysts remained high (above 65%) even after a 5th reuse cycle, which reflected the high stability of Fe/Ni@ZIF-8. Overall, this study demonstrated that Fe/Ni@ZIF-8 had significant potential for the removal of OFX from wastewaters with a removal efficiency >90%.

Green synthesis of Mn3O4 nanoparticles using Costus woodsonii flowers extract for effective removal of malachite green dye

The pollution of organic dyes such as malachite green is one of the globally critical issues, calling for efficient mitigation methods. Herein, we developed green Mn₃O₄ nanoparticles synthesized using natural compounds extracted from Costus woodsonii flowers under an ultrasound-assisted mode. The materials were characterized using several physicochemical techniques such as Fourier-transform infrared spectroscopy, X-ray diffraction, Energy-dispersive X-ray spectroscopy, scanning electron microscopy, Raman spectroscopy, and N₂ adsorption desorption isotherm measurement. The X-ray diffraction and N₂ isotherm plots confirmed the presence of tetragonal γ-Mn₃O₄ phase and mesoporous structure, respectively. Carbonyl groups derived from flavonoids or carboxylic compounds were found in the surface of green Mn₃O₄ nanoparticles. The effect of pH, contact time, dose, and concentration on the adsorption of malachite green over green Mn₃O₄ was carried out. The maximum malachite green adsorption capacity for green Mn₃O₄ nanoparticles was 101-162 mg g^-1. Moreover, kinetic and isotherm adsorption of malachite green obeyed Langmuir (R_adj.² = 0.980-0.995) and pseudo first-order models (R_adj.² = 0.996-1.00), respectively. Adsorption of malachite green over green Mn₃O₄ was a thermodynamically spontaneous process due to negative Gibbs free energy values (ΔG^ο < 0). Green Mn₃O₄ nanoparticles offered a high stability through the FR-IR spectra analysis. With a good recyclability of 4 cycles, green Mn₃O₄ nanoparticles can be used as potential adsorbent for removing malachite green dye from water.

Simultaneous removal of arsenite and arsenate from mining wastewater using ZIF-8 embedded with iron nanoparticles

Arsenic contamination is an increasing global environmental problem, especially in mining industry wastewater where both arsenite (As(III)) and arsenate (As(V)) have been routinely detected. In this paper, a novel porous metal-organic framework material (ZIF-8) was composited with iron nanoparticles (FeNPs) to form a functional material (ZIF-8@FeNPs) for the simultaneous removal of As(III)/(V) from wastewater. The material effectively removed both As(III) and As(V) with removal efficiencies of 99.9 and 71.2%, respectively. Advanced characterization techniques including X-ray photoelectron spectroscopy (XPS) and Fourier infrared (FTIR) indicated that removal of As(III) and As(V) involved complex formation. Adsorption kinetics followed a pseudo-second order kinetics indicating adsorption involved chemisorption. After four cycles of reuse the he removal rate of As species was still relatively high at > 60% When ZIF-8@FeNPs were used to remove As from real wastewater from acid mines the removal efficiency was 94.27%. Finally, a As(III) and As(V) removal mechanism was proposed.

Fabrication and characterization of magnetic nanomaterials for the removal of toxic pollutants from water environment: A review

The success of any sustainable growth represents an advancement of novel approaches and new methodologies for managing any ecological concern. Magnetic nanoparticles have gained recent interest owing to their versatile properties such as controlled size, shape, quantum and surface effect, etc, and outcome in wastewater treatment and pollutant removal. Developments have progressed in synthesizing magnetic nanoparticles with the required size, shape and morphology, surface and chemical composition. Magnetic nanoparticles are target specific and inexpensive compared to conventional treatment techniques. This review insight into the synthesis of magnetic nanoparticles using physical, chemical, and biological methods. The biological method of synthesizing magnetic nanoparticles serves to be cost-effective, green process, and eco-friendly for various applications. Characterization studies of synthesized nanoparticles using TEM, XRD, SARS, SANS, DLS, etc are discussed in detail. Magnetic nanoparticles are widely utilized in recent research for removing organic and inorganic contaminants. It was found that the magnetic nanosorption approach together with redox reactions proves to be an effective and flexible mechanism for the removal of pollutants from waste effluents.

Evaluation of In Vitro Cytotoxic, Genotoxic, Apoptotic, and Cell Cycle Arrest Potential of Iron-Nickel Alloy Nanoparticles

The use of iron-nickel alloy nanoparticles (Fe-Ni ANPs) is increasing daily in various fields. People are increasingly exposed to these nanoparticles for occupational and environmental reasons. Our study determined some of the effects of Fe-Ni ANP exposure and impacts on human health at the cellular level. The cytotoxic and genotoxic potentials of Fe-Ni ANPs were investigated by XTT, clonogenic, comet, and GammaH2AX analyses using Beas-2B cells. Annexin V, multicaspase, and cell cycle arrest methods were used to understand the apoptotic mechanism of action. The intracellular ROS method was used to determine the primary mechanism that leads to cytotoxic and genotoxic activity. The Fe-Ni ANPs showed cytotoxic activity with the XTT and clonogenic methods: they had genotoxic potential, as demonstrated via genotoxicity methods. It was determined that the cytotoxic effect was realized by the caspase-dependent apoptotic pathway, and the cells were stopped at the G0/G1 stage by Fe-Ni ANPs. Increased intracellular ROS due to Fe-Ni ANPs led to cytotoxic, genotoxic, and apoptotic activity. Potential risks to human health due to Fe-Ni ANPs were then demonstrated at the cellular level.

Mechanistic insights into carbo-catalyzed persulfate treatment for simultaneous degradation of cationic and anionic dye in multicomponent mixture using plastic waste-derived carbon

Upcycling waste into value-added products for utilization in wastewater abatements has been explored in a number of treatment technologies. One such waste, single-use plastic, which poses significant adverse environmental and economic impact, has been chosen and converted into graphitic carbon to reduce the waste burden sustainably and economically. The sorptive and catalytic performance of synthesized plastic waste-derived carbon (PWC) was evaluated using brilliant green (BG) and eosin yellow (EY) as target pollutants. The adsorption capacity of PWC was very low for BG (7.41 mg/g) and EY (4.93 mg/g). The coupling of PWC with peroxymonosulfate (PMS) promoted dye degradation. Complete degradation of the dye, with ~61% reduction in TOC and ~95% reduction in toxicity, was achieved by oxidative treatment (initial concentration: 10 mg/L). The functionalities of PWC facilitated better electron transfer to PMS for its effective activation, which led to the production of SO₄^•- and OH^•. The quenching study confirmed that the degradation of dyes was primarily due to SO₄^•-. Additionally, the pathways of dye degradation were proposed based on the intermediates identified. Thus, this study established the high potential of PWC as a metal-free catalyst in PMS activation for the abatement of organic pollutants.

Significantly Promoting the Photogenerated Charge Separation by Introducing an Oxygen Vacancy Regulation Strategy on the FeNiOOH Co-Catalyst

Semiconductor/co-catalyst coupling is considered as a promising strategy to enhance the photoelectrochemical (PEC) conversion efficiency. Unfortunately, this model system is faced with a serious interface recombination problem, which limits the further improvement of PEC performances. Here, a FeNiOOH co-catalyst with abundant oxygen vacancies on BiVO₄ is fabricated through simple and economical NaBH₄ reduction to accelerate hole transfer and achieve efficient electron-hole pair separation. The photocurrent of the BV (BiVO₄ )/Vo-FeNiOOH system is more than four times that of pure BV. Importantly, the charge transfer kinetics and charge carrier recombination process are studied by scanning photoelectrochemical microscopy and intensity modulated photocurrent spectroscopy in detail. In addition, the oxygen vacancy regulation proposed is also applied successfully to other semiconductors (Fe₂ O₃ ), demonstrating the applicability of this strategy.

New insights into iron/nickel-carbon ternary micro-electrolysis toward 4-nitrochlorobenzene removal: Enhancing reduction and unveiling removal mechanisms

The ternary micro-electrolysis material iron/nickel-carbon (Fe/Ni-AC) with enhanced reducibility was constructed by introducing the trace transition metal Ni based on the iron/carbon (Fe/AC) system and used for the removal of 4-nitrochlorobenzene (4-NCB) in solution. The composition and structures of the Fe/Ni-AC were analyzed by various characterizations to estimate its feasibility as reductants for pollutants. The removal efficiency of 4-NCB by Fe/Ni-AC was considerably greater than that of Fe/AC and iron/nickel (Fe/Ni) binary systems. This was mainly due to the enhanced reducibility of 4-NCB by the synergism between anode and double-cathode in the ternary micro-electrolysis system (MES). In the Fe/Ni-AC ternary MES, zero-iron (Fe⁰) served as anode involved in the formation of galvanic couples with activated carbon (AC) and zero-nickel (Ni⁰), respectively, where AC and Ni⁰ functioned as double-cathode, thereby promoting the electron transfer and the corrosion of Fe⁰. The cathodic and catalytic effects of Ni⁰ that existed simultaneously could not only facilitate the corrosion of Fe⁰ but also catalyze H₂ to form active hydrogen (H*), which was responsible for 4-NCB transformation. Besides, AC acted as a supporter which could offer the reaction interface for in-situ reduction, and at the same time provide interconnection space for electrons and H₂ to transfer from Fe⁰ to the surface of Ni⁰. The results suggest that a double-cathode of Ni⁰ and AC could drive much more electrons, Fe²⁺ and H*, thus serving as effective reductants for 4-NCB reduction.

Cu-coupled Fe/Fe3C covered with thin carbon as stable win-win catalysts to boost electro-Fenton reaction for brewing leachate treatment

The electro-Fenton oxidation is one of the powerful approaches for achieving the complete mineralization of organic pollutants in water. The key dilemma for efficient industrial application of electro-Fenton oxidation is the complicated post-processing of iron sludge, and the cost and risk associated with H₂O₂ transportation and storage. Herein, Cu-coupled Fe/Fe₃C covered with carbon layer on carbon felt (Cu-Fe/Fe₃C@C), engineered by a hydrothermal reaction followed by the consequent thermal-treatment in N₂ atmosphere, as a self-supported integrated cathode were used for an onsite oxygen reduction reaction and a Fenton oxidation reaction. Experimental evidences demonstrate that, at the operating potential of -1.1 V, Fe₃C can selectively catalyze O₂ into H₂O₂ by 2e reduction pathways with assistance of metal Cu. Meanwhile, metal Fe and Cu incorporated into Cu-Fe/Fe₃C@C simultaneously motivate the onsite Fenton oxidation arose by H₂O₂. Such a win-win catalyst presented high activity in the electro-Fenton process. In acidic environment, the efficient mineralization rate of methylene blue, nitrobenzene, phenol, and bisphenol A can reach more than 70% in 60 min, as well as the excellent stability and durability due to the protection of graphited carbon layer. Compared with tradition electrochemical degrade system, the prepared Cu-Fe/Fe₃C@C electrode as cathode for practical refractory brewing leachate treatment reveal more efficient decolorization and mineralization, saving 14.3% of electricity.

Enhanced Sonocatalytic Performance of Non-Metal Graphitic Carbon Nitride (g-C3N4)/Coconut Shell Husk Derived-Carbon Composite

This study focused on the modification of graphitic carbon nitride (g-C3N4) using carbon which was obtained from the pyrolysis of coconut shell husk. The sonocatalytic performance of the synthesized samples was then studied through the degradation of malachite green. In this work, pure g-C3N4, pure carbon and carbon/g-C3N4 composites (C/g-C3N4) at different weight percentages were prepared and characterized by using XRD, SEM-EDX, FTIR, TGA and surface analysis. The effect of carbon amount in the C/g-C3N4 composites on the sonocatalytic performance was studied and 10 wt% C/g-C3N4 showed the best catalytic activity. The optimization study was conducted by using response surface methodology (RSM) with a central composite design (CCD) model. Three experimental parameters were selected in RSM including initial dye concentration (20 to 25 ppm), initial catalyst loading (0.3 to 0.5 g/L), and solution pH (4 to 8). The model obtained was found to be significant and reliable with R2 value (0.9862) close to unity. The degradation efficiency of malachite green was optimized at 97.11% under the conditions with initial dye concentration = 20 ppm, initial catalyst loading = 0.5 g/L, solution pH = 8 after 10 min. The reusability study revealed the high stability of 10 wt% C/g-C3N4 as sonocatalyst. In short, 10 wt% C/g-C3N4 has a high potential for industrial application since it is cost effective, reusable, sustainable, and provides good sonocatalytic performance.

Research progress of metal organic frameworks and their derivatives for adsorption of anions in water: A review

Anion pollution in water has become a problem that cannot be ignored. The anion concentration should be controlled below the national emission standard to meet the demand for clean water. Among the methods for removing excess anions in water, the adsorption method has a unique removal performance, and the core of the adsorption method is the adsorbent. In recent years, the emerging metal-organic frameworks (MOFs) have the advantages of adjustable porosity, high specific surface area, diverse functions, and easy modification. They are very competitive in the field of adsorption of liquid anions. This article focuses on the adsorption of fluoride, arsenate, chromate, radioactive anions (ReO₄^-, TcO₄^-, SeO₄^2-/SeO₃^2-), phosphate ion, chloride ion, and other anions by MOFs and their derivatives. The preparation methods of MOFs are introduced in turn, the application of different types of metal-based MOFs to adsorb various anions were discussed in categories with their crystal structure and functional groups. The influence on the adsorption of anions is analyzed, including the more common and special adsorption mechanisms, adsorption kinetics and thermodynamics, and regeneration performance are briefly described. Finally, the current situation of MOFs adsorption of anions is summarized, and the outlook for future development is summarized to provide my own opinions for the practical application of MOFs.

Performance of 2D MXene as an adsorbent for malachite green removal

The utilization of novel materials is one of the reliable solutions for wastewater remediation processes, where they could be applied as adsorbents. Among these materials, MXenes are increasingly used composites in different applications, including water treatment techniques, due to their exceptional properties that enhance the total performance. In this work, we used Ti₃C₂T_x MXene as an adsorbent for the Malachite Green dye removal, considering the dye's chromatic and leuco forms. Effects of adsorbent dose, pH, contact time, and dye's initial concentration on the removal efficiency were studied. Three adsorption isotherms, namely Freundlich, Langmuir, and Temkin, were studied to find the best fitting model with the practical results, where the Freundlich model had the highest R², 0.974. Furthermore, five kinetics models were used to study the adsorption kinetics; these are zero-order, pseudo-first-order, pseudo-second-order, Elovich, and intraparticle diffusion. However, the pseudo-second-order model showed the highest R² value of 0.999. It was found that as the adsorbent dose increases, the removal efficiency increases and reaches 94.1% when the dose was 0.09 g in a 50 ml solution. Interestingly, it was noticed that the removal efficiency increases as the pH increases or decreases; the minimum efficiency was noticed at pH = 6. This was attributed to the leuco nature of the dye; whereas the pH increases, the dye turns colorless and becomes hard to detect. This finding shows that the removal is high when the pH is low, and it is low as the pH gets high but cannot be detected because of the color loss. The removal efficiency dramatically increased as the contact time increased at first; however, at 60 min, it almost reached the study state and the follwoing change was marginal. Finally, the removal efficiency decreased as the dye's initial concentration increased.

Facile and scalable preparation of ZIF-67 decorated cotton fibers as recoverable and efficient adsorbents for removal of malachite green

Recently, metal–organic frameworks (MOFs) have received considerable attention as highly efficient adsorbents for dye wastewater remediation. However, the immobilization of MOFs on the substrate surfaces to fabricate easy recyclable adsorbents via a facile route is still a challenge. In this work, ZIF-67/cotton fibers as adsorbents for dye removal were prepared in a large-scale using a simple coordination replication method. The successful fabrication of the ZIF-67/cotton fibers was confirmed by FTIR, XRD, XPS, SEM and BET analysis, respectively. As expected, the as-prepared ZIF-67/cotton fibers exhibited high adsorption capacity of 3787 mg/g towards malachite green (MG). Meanwhile, the adsorption kinetics and isotherm obeyed the pseudo-second-order kinetics and Langmuir model, respectively. Moreover, its removal efficiency towards MG was not significantly influenced by the pH and ionic strength of aqueous solution. Most importantly, the ZIF-67/cotton fibers can remove MG from synthetic effluents, and it can be easily regenerated without filtration or centrifugation processes, with the regeneration efficiency remaining over 90% even after 10 cycles. Additionally, the ZIF-67/cotton fibers presented excellent antimicrobial performance against E. coli and S. aureus. Hence, the distinctive features of the as-prepared ZIF-67/cotton fibers make it promisingly applicable for the colored wastewater treatment.