A rational design of g-C3N4-based ternary composite for highly efficient H2 generation and 2,4-DCP degradation

Design and Fabrication of Biomass Derived Black Carbon Modified g-C3N4/FeIn2S4 Heterojunction as Highly Efficient Photocatalyst for Wastewater Treatment

The environmental deterioration caused by dye wastewater discharge has received considerable attention in recent decades. One of the most promising approaches to addressing the aforementioned environmental issue is the development of photocatalysts with high solar energy consumption efficiency for the treatment of dye-contaminated water. In this study, a novel low-cost π-π biomass-derived black carbon modified g-C3N4 coupled FeIn2S4 composite (i.e., FeInS/BC-CN) photocatalyst is successfully designed and fabricated that reveals significantly improved photocatalytic performance for the degradation of Eosin Yellow (EY) dye in aqueous solution. Under dark and subsequent visible light irradiation, the amount optimized composite reveals 99% removal performance for EY dye, almost three-fold compared to that of the pristine FeInS and BC-CN counterparts. Further, it is confirmed by means of the electron spin resonance spectrometry, quenching experiments, and density functional theory (DFT) calculations, that the hydroxyl radicals (•OH) and superoxide radicals (•O2 -) are the dominant oxidation species involved in the degradation process of EY dye. In addition, a systematic photocatalytic degradation route is proposed based on the resultant degradation intermediates detectedduring liquid chromatography tandem mass spectrometry (LC-MS/MS) analysis. This work provides an innovative idea for the development of advanced photocatalysts to mitigate water pollution.

Preparation and characterization of sulphur and zinc oxide Co-doped graphitic carbon nitride for photo-assisted removal of Safranin-O dye

Recently, there has been significant interest in photocatalytic reactions involving graphitic carbon nitride (g-C3N4) due to its sp2-hybridized carbon and nitrogen content and it is an ideal candidate for blending with other materials to enhance performance. Here, we have synthesized and analyzed both doped and undoped g-C3N4 nanoparticles. Specifically, we co-doped sulfur (S) into g-C3N4, integrated it with ZnO particles, and investigated the photocatalytic potential of these nanocomposites to remove Safranin-O dye. The initial step involved the preparation of pure g-C3N4 through calcination of urea. Subsequently, S-g-C3N4 was synthesized by calcining a mixture of urea and thiourea with a 3 : 1 ratio. Finally, the ZnO-S-g-C3N4 composite was synthesized using the liquid exfoliation technique, with distilled water serving as the exfoliating solvent. These samples were characterized by advanced techniques, including UV-Vis spectroscopy, Fourier-transform infrared spectroscopy (FTIR), X-ray Diffraction (XRD), energy dispersive X-ray (EDX) and scanning electron microscopy (SEM), to assess their crystallinity, morphology, optical properties, and phase purity. Subsequently, these nanocomposites were employed in catalytic and photocatalytic processes to remove the Safranin-O dye (SO). The results highlighted the formation of Z-scheme junction responsible for ZnO-S-g-C3N4's significant performance improvement. The comparison of results demonstrated that S-g-C3N4 and ZnO-S-g-C3N4 composites revealed an effective removal of Safranin-O dye in the presence of UV-light as compared to pure g-C3N4, as it was attributed to the phenomenon of improved separation of photogenerated charge carriers as a result of heterojunction formation between S-g-C3N4 and ZnO interfaces. In addition to improving photocatalytic performance, this study presents a facile route for producing ZnO-S-g-C3N4 composite with superior adsorption capabilities and selectivity.

Designing State-of-the-Art Gas Sensors: From Fundamentals to Applications

Gas sensors are crucial in environmental monitoring, industrial safety, and medical diagnostics. Due to the rising demand for precise and reliable gas detection, there is a rising demand for cutting-edge gas sensors that possess exceptional sensitivity, selectivity, and stability. Due to their tunable electrical properties, high-density surface-active sites, and significant surface-to-volume ratio, nanomaterials have been extensively investigated in this regard. The traditional gas sensors utilize homogeneous material for sensing where the adsorbed surface oxygen species play a vital role in their sensing activity. However, their performance for selective gas sensing is still unsatisfactory because the employed high temperature leads to the poor stability. The heterostructures nanomaterials can easily tune sensing performance and their different energy band structures, work functions, charge carrier concentration and polarity, and interfacial band alignments can be precisely designed for high-performance selective gas sensing at low temperature. In this review article, we discuss in detail the fundamentals of semiconductor gas sensing along with their mechanisms. Further, we highlight the existed challenges in semiconductor gas sensing. In addition, we review the recent advancements in semiconductor gas sensor design for applications from different perspective. Finally, the conclusion and future perspectives for improvement of the gas sensing performance are discussed.

Fabrication of a PCN/BiOBr 2D hybrid with improved photocatalytic performance of 2,4-dichorophenol degradation

Photocatalysis has received much attention as an environmentally friendly route to manage the emerging organic pollution problems. Herein, BiOBr nanosheets have been synthesized by a hydrothermal method, and then PCN/BiOBr hybrids are designed via a facile wet chemical method. The as-prepared PCN/BiOBr hybrids are characterized by X-ray diffraction (XRD), UV-vis diffuse reflectance spectra (UV-vis DRS), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The PCN/BiOBr composite exhibits remarkable improved activity in the degradation of 2,4-dichlorophenol (2,4-DCP) as compared to the pristine BiOBr. Based on the ·OH amount-related fluorescence spectra fluorescence and the photoelectrochemistry (PEC) tests, it is confirmed that the enhanced photocatalytic performance of PCN/BiOBr is attributed to the promoted charge separation. Moreover, by means of the radical-trapping experiments it is demonstrated that the formed ·O2- species, as the electron-modulated direct products, are the primary active species during the photocatalytic degradation of 2,4-DCP. This work would provide a feasible design strategy to fabricate high-activity photocatalysts for 2,4-DCP degradation.

Bagasse cellulose-based S-type Bi2O3/Zn3In2S6 photocatalyst for efficient and stable degradation of 2,4-dichlorophenol under visible light

The environmental and human health hazards posed by 2,4-dichlorophenol (2,4-DCP) call for effective degradation technologies. This research investigates the design and application of a Bi2O3/Zn3In2S6 heterojunction photocatalyst, a 'S scheme', which was constructed via a simple hydrothermal method. The photocatalyst was then embedded in a sugarcane bagasse cellulose carrier (SBC/BO/ZIS), demonstrating excellent 2,4-DCP degradation capacity. The results show that S-type Bi2O3/Zn3In2S6 promotes the separation of photogenerated carriers. The SBC/BO/ZIS complex, in comparison with Bi2O3 and Zn3In2S6 alone, amplifies specific surface area (91.7880 m2/g) and broadens the light absorption range (570 nm) of materials, showing robust photocatalytic performance. The degradation rate of 50 mg/L 2,4-DCP reached an impressive 97% within 120 min. The encapsulation of BO/ZIS in SBC not only increases the efficiency of material recovery and recycling but also allows for continuous degradation of 2,4-DCP in cyclic manners, maintaining a degradation rate between 90% and 97%. XRD characterization shows that the physical properties of the material are not affected. The degradation of 2,4-DCP was dominantly controlled by active species (·OH and ·O2-) identified by electron paramagnetic resonance analysis and free radical trapping experiments. This innovative design significantly enhances sunlight utilization and effectively curbs charge carrier recombination, while also promoting material recovery and utilization. These attributes establish a foundation for a cost-effective and efficient means of treating actual wastewater containing 2,4-DCP.

Solar light driven enhanced photocatalytic treatment of azo dye contaminated water based on Co-doped ZnO/ g-C3N4 nanocomposite

The current research concentrated on the Co-precipitation synthesis of g-C3N4 (CN), ZnO, ZnO/CN, and Co-doped ZnO/CN nanocomposite, as well as the solar light enhanced photocatalytic treatment of Reactive Red 120 (RR120) from genuine wool textile effluent. The 3D flower-like structure of Co-doped ZnO distributed on the surface of CN thin sheets, according to structural studies employing XRD and SEM examinations Electrochemical experiments exhibited that the Co-doped ZnO/CN nanocomposite has a large electroactive surface area. The optical band-gap values of CN, ZnO, ZnO/CN, and Co-doped ZnO/CN nanocomposites were 2.68, 3.13, 2.38, and 2.23 eV, respectively, according to optical characterizations. The synergistic effects and heterojunction produced by Co-doped ZnO and CN can be linked to the narrow gap in nanocomposites. After 75, 60, 50, and 40 min of exposure to solar light, photocatalytic degradation assays for 250 mL of 20 mg/L RR120 solution in the presence of CN, ZnO, ZnO/CN, and Co-doped ZnO/CN nanocomposites demonstrated 100% dye treatment. The applicability of photocatalysts for decolorization of 250 mL of 10 mg/L RR120 prepared from actual wool textile wastewater was investigated, and the results showed that Co-doped ZnO/CN nanocomposites for treatment of RR120 from actual wool textile wastewater were highly efficient at photocatalytic degradation.

Enhanced Photocatalytic H2 Evolution Performance of the Type-II FeTPPCl/Porous g-C3N4 Heterojunction: Experimental and Density Functional Theory Studies

It is of great significance to improve the photocatalytic performance of g-C3N4 by promoting its surface-active sites and engineering more suitable and stable redox couples. Herein, first of all, we fabricated porous g-C3N4 (PCN) via the sulfuric acid-assisted chemical exfoliation method. Then, we modified the porous g-C3N4 with iron(III) meso-tetraphenylporphine chloride (FeTPPCl) porphyrin via the wet-chemical method. The as-fabricated FeTPPCl-PCN composite revealed exceptional performance for photocatalytic water reduction by evolving 253.36 and 8301 μmol g-1 of H2 after visible and UV-visible irradiation for 4 h, respectively. The performance of the FeTPPCl-PCN composite is ∼2.45 and 4.75-fold improved compared to that of the pristine PCN photocatalyst under the same experimental conditions. The calculated quantum efficiencies of the FeTPPCl-PCN composite for H2 evolution at 365 and 420 nm wavelengths are 4.81 and 2.68%, respectively. This exceptional H2 evolution performance is because of improved surface-active sites due to porous architecture and remarkably improved charge carrier separation via the well-aligned type-II band heterostructure. Besides, we also reported the correct theoretical model of our catalyst through density functional theory (DFT) simulations. It is found that the hydrogen evolution reaction (HER) activity of FeTPPCl-PCN arises from the electron transfer from PCN via Cl atom(s) to Fe of the FeTPPCl, which forms a strong electrostatic interaction, leading to a decreased local work function on the surface of the catalyst. We suggest that the resultant composite would be a perfect model for the design and fabrication of high-efficiency heterostructure photocatalysts for energy applications.

A novel approach to redox active polymers: Decolorization of methylene blue by heterogeneous reduction with redox active azo polymer

The existing reducing agents used in the literature to decolorization of methylene blue are soluble in water and the reduction process is carried out in a homogeneous redox reaction medium. After the decolorization process, the reducing agents and its by-products remain in a homogeneous redox reaction medium. Many of these reducing agents are toxic and cause chemical pollution of textile wastewater. Therefore, there is a need for reducing agents that can be mixed heterogeneously with water from which the reducing agent can be easily removed from a redox reaction medium. For this purpose, water-insoluble redox active azo polymer was synthesized from redox active 1,4-dihydroxybenzene and p-phenylenediamine. The synthesized redox active azo polymer was used for decolorization of methylene blue by heterogeneous reduction and various kinetic parameters were investigated for this redox reaction. At the same time, the investigated results of azo polymer and monomer (1,4-dihydroxybenzene) were compared.

Graphitic-C3N4/chitosan-doped NiO nanostructure to treat the polluted water and their bactericidal with in silico molecular docking analysis

Different concentrations (2 and 4 wt%) of graphite carbon nitride (g-C3N4) was doped into fixed amount of chitosan (CS) and nickel oxide (NiO) nanoparticles (NPs) via a co-precipitation route. The aim of study is to remove the pollutants from wastewater through catalytic activity (CA) and determine the bactericidal activities of synthesized products. X-ray diffraction pattern confirmed the cubic structure of NiO NPs and peak shifted to higher angle upon g-C3N4 doping. Fourier transform infrared spectroscopy revealed the existence of bending and stretching vibration mode. The absorption decreased gradually accompanied blue-shift and assessed bandgap energy increased upon doping. The high resolution transmission electron microscopy micrographs confirmed the formation of cubic-shaped NPs and elongated nanorods were seen for NiO and co-doped NiO. The catalytic efficiency of samples was examined using methylene blue (MB) in the presence of reducing agent. A remarkable dye de-colorization was confirmed with a g-C3N4 and CS doping; moreover, the bactericidal efficacy compared to Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) was observed as 3.15 and 13.8 mm, respectively. In silico, molecular docking investigations targeting against b-lactamaseS. aureus and FabHE. coli enzymes assisted to elaborate the mechanism underlying microbicidal action of the NPs.

Insight into the role of Fe in the synergetic effect of persulfate/sulfite and Fe2O3@g-C3N4 for carbamazepine degradation

In this work, the role of Fe in the synergetic effect of persulfate/sulfite and Fe₂O₃@g-C₃N₄ (FCN) for carbamazepine (CBZ) degradation was studied. Unexpectedly, Fe₂O₃ in FCN plays very different roles for sulfite [S(IV)] and persulfate (PS) activation. Specifically, since photo-generated holes (h⁺) can transform S(IV) into SO₄^-, and photo-generated electrons (e^-) can accelerate Fe(III) reduction which promotes transition metal based S(IV) activation, a synergetic effect of photocatalysis and Fe is observed in FCN/S(IV)/vis system. In contrast, in FCN/PS/vis system, both Fe(III)/Fe(II) cycle and PS activation compete for e^-. Since PS is a stronger electron acceptor, Fe(III) reduction by e^- is limited. Therefore, the contribution of Fe₂O₃ in FCN/S(IV)/vis system is 3 times higher than that in FCN/PS/vis system. Initial pH affects CBZ removal by changing surface charge of catalysts and oxidants species, while the effect varies for different catalysts and oxidants. This study provides new insight into the synergetic effect of photocatalysis and transition metal for SO₄^- generation, which contributes to catalyst design for environmental application.

Recent Progress in the Synthesis and Applications of Composite Photocatalysts: A Critical Review

Photocatalysis is an advanced technique that transforms solar energy into sustainable fuels and oxidizes pollutants via the aid of semiconductor photocatalysts. The main scientific and technological challenges for effective photocatalysis are the stability, robustness, and efficiency of semiconductor photocatalysts. For practical applications, researchers are trying to develop highly efficient and stable photocatalysts. Since the literature is highly scattered, it is urgent to write a critical review that summarizes the state-of-the-art progress in the design of a variety of semiconductor composite photocatalysts for energy and environmental applications. Herein, a comprehensive review is presented that summarizes an overview, history, mechanism, advantages, and challenges of semiconductor photocatalysis. Further, the recent advancements in the design of heterostructure photocatalysts including alloy quantum dots based composites, carbon based composites including carbon nanotubes, carbon quantum dots, graphitic carbon nitride, and graphene, covalent-organic frameworks based composites, metal based composites including metal carbides, metal halide perovskites, metal nitrides, metal oxides, metal phosphides, and metal sulfides, metal-organic frameworks based composites, plasmonic materials based composites and single atom based composites for CO₂ conversion, H₂ evolution, and pollutants oxidation are discussed elaborately. Finally, perspectives for further improvement in the design of composite materials for efficient photocatalysis are provided.

Preparation of Bi3Fe0.5Nb1.5O9/g-C3N4 heterojunction photocatalysts and applications in the photocatalytic degradation of 2,4-dichlorophenol in environment

The energy band relationship and the active substances were studied to determine photocatalyst accords with the Z-type transfer mechanism.

Plasmon Assisted Highly Efficient Visible Light Catalytic CO2 Reduction Over the Noble Metal Decorated Sr-Incorporated g-C3N4

The photocatalytic performance of g-C₃N₄ for CO₂ conversion is still inadequate by several shortfalls including the instability, insufficient solar light absorption and rapid charge carrier's recombination rate. To solve these problems, herein, noble metals (Pt and Au) decorated Sr-incorporated g-C₃N₄ photocatalysts are fabricated via the simple calcination and photo-deposition methods. The Sr-incorporation remarkably reduced the g-C₃N₄ band gap from 2.7 to 2.54 eV, as evidenced by the UV-visible absorption spectra and the density functional theory results. The CO₂ conversion performance of the catalysts was evaluated under visible light irradiation. The Pt/0.15Sr-CN sample produced 48.55 and 74.54 µmol h^-1 g^-1 of CH₄ and CO, respectively. These amounts are far greater than that produced by the Au/0.15Sr-CN, 0.15Sr-CN, and CN samples. A high quantum efficiency of 2.92% is predicted for the Pt/0.15Sr-CN sample. Further, the stability of the photocatalyst is confirmed via the photocatalytic recyclable test. The improved CO₂ conversion performance of the catalyst is accredited to the promoted light absorption and remarkably enhanced charge separation via the Sr-incorporated mid gap states and the localized surface plasmon resonance effect induced by noble metal nanoparticles. This work will provide a new approach for promoting the catalytic efficiency of g-C₃N₄ for efficient solar fuel production.