In situ produced Co9S8 nanoclusters/Co/Mn-S, N multi-doped 3D porous carbon derived from eriochrome black T as an effective bifunctional oxygen electrocatalyst for rechargeable Zn-air batteries

Co-doping regulation on Ni-based electrocatalysts to adjust the selectivity of oxygen reduction reaction for Zn-air batteries and H2O2 production

Although Ni-based materials are widely used as electrocatalysts, it remains necessary to further explore their selectivity towards the four- or two-electron oxygen reduction reaction (ORR). Herein, it is proposed to synthesize NiO@NCNTs (NCNTs = N-doped carbon nanotubes) using a metal-organic framework (MOF), [Ni(BZIDA)(H2O)]n (NiMOF, BZIDA = benzimidazole-5,6-dicarboxylic acid), as a precursor after calcination with dicyandiamide (DCDA). Regarding NiO@NCNTs, small NiO particles are distributed in NCNTs derived from DCDA homogeneously. NiO@NCNTs act as a typical two-electron electrocatalyst. The H2O2 production rate of NiO@NCNTs reaches 0.5 mol g-1 h-1 at 0.46 V (vs. RHE). After the doping of Co2+ in NiMOF, Co/NiO@NCNTs were synthesized using a similar method, with the four-electron character shown in ORR. A Zn-air battery was assembled by applying Co/NiO@NCNTs as the cathode material. When discharge occurs at 5 and 10 mA cm-2, its specific capacitance reaches 779.3 and 832.2 mA h g-1 with an energy density of 928.6 and 948.5 W h kg-1, respectively. Theoretical calculations suggest a variation in ORR selectivity between NiO@NCNTs and Co/NiO@NCNTs, which results from their different interactions with OOH*. This study demonstrates the effect of the structure on ORR selectivity for Ni-based electrocatalysts.

Tailoring phases of ferrihydrite/α-Fe2O3@C nanocomposites using syringyl and guaiacyl-rich biomass-derived carbon nanodots for electrochemical application

Biomass-derived carbon nanodots (CNDs) hold promise as effective reducing agents for metal oxide nanoparticles yet understanding the intricate interplay with CND structure remains challenging. This study explores the impact of lignin types, specifically syringyl (S), and guaiacyl (G) units in CNDs on metal oxide phases and their electrochemical activity toward dopamine oxidation. We design phases of ferrihydrite/α-Fe2O3@C nanocomposites, using hazelnut carbon nanodots (HS-CNDs (S-rich)) and beetroot carbon nanodots (BS-CNDs (G-rich)) via a one-pot hydrothermal technique. Our findings show S units in HS-CNDs promote α-FeOOH/α-Fe2O3@CHS, while G units in BS-CNDs favor α (β)-FeOOH/α-Fe2O3@CBS. In contrast to α(β)-FeOOH/α-Fe2O3@CBS, α-FeOOH/α-Fe2O3@CHS exhibits superior electrochemical performance in dopamine oxidation due to its larger electrochemical active surface area, higher absorbance capacity, and shortened electron transfer length. Moreover, α-FeOOH/α-Fe2O3@CHS nanocomposites demonstrate remarkable dopamine selectivity, achieving rapid detection response in 10 s with a low LOD of 4 nM within a broad linear range (0.05-0.3 μM), demonstrating impressive reproducibility (97.5 %), stability (96.4 %), and works in real-time human urine detection with a recovery rate of ranging from 94.57 % and 102.2 %. Therefore, the utilization of biomass-derived CNDs, particularly S and G units-rich CNDs, in tailoring the phases of ferrihydrite/α-Fe2O3@C nanocomposites for electrochemical dopamine detection is promising.

Phosphorus-doped nickel cobalt oxide (NiCo2O4) wrapped in 3D hierarchical hollow N-doped carbon nanoflowers as highly efficient bifunctional electrocatalysts for overall water splitting

Properly design and fabricate capable electrocatalysts with 3D hierarchical hollow framework to realize cost-effective and efficacious overall water splitting (OWS) are particularly meaningful for the large-scale arrangement of pivotal energy technology. In this study, P-doped NiCo2O4 nanoparticles encapsulated in N-doped carbon hierarchical hollow nanoflowers (P-NiCo2O4@NCHHNFs) were constructed using the hydrothermal-pyrolysis-phosphorization approach. This fascinating architecture can not merely serve as a conductive pathway for electron transfer, but at the same time effectively inhibited the aggregation and corrosion of the NiCo2O4 nanoparticles. Additionally, the P doping not only regulates electronic structure configuration to boost the intrinsic activity of the catalyst, but also enhance electrochemical surface areas to reveal more accessible active sites. Attributing to these characteristics, the as-prepared P-NiCo2O4@NCHHNFs exhibit preeminent electrocatalytic performance with low overpotentials of 283 mV and 162 mV for oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) (at 10 mA cm-2), respectively. Specifically, by using the P-NiCo2O4@NCHHNFs as bifunctional catalysts, a low potential of 1.56 V (at 10 mA cm-2) is sufficient to drive overall water splitting with splendid durability. This study proposed an innovative strategy for the conceiving and fabricating high-performance catalysts via heteroatom-doping.

Mechanism insight into the N-C polar bond and Pd-Co heterojunction for improved hydrogen evolution activity

Constructing platinum-like materials with excellent catalytic activity and low cost has great significance for hydrogen evolution reaction (HER) during electrolysis of water. Herein, palladium nanoparticles (NPs) deposition on the surface of Co NPs using nitrogen-doped carbon (NC) as substrate, denoted as N-ZIFC/CoPd-30, are manufactured and served as HER electrocatalysts. Characterization results and density functional theory calculations validate that Pd-Co heterojunctions with NC acting as "electron donators" promote the Pd species transiting to the electron-rich state based on an efficient electron transfer mechanism, namely the N-C polar bonds induced strong metal-support interaction effect. The electron-rich Pd sites are beneficial to HER. Satisfactorily, N-ZIFC/CoPd-30 have only low overpotentials of 16, 162, and 13 mV@-10 mA cm-2 with the small Tafel slopes of 98 mV/decade, 126 mV/decade, and 72 mV/decade in pH of 13, 7, and 0, respectively. The success in fabricating N-ZIFC/CoPd opens a promising path to constructing other platinum-like electrocatalysts with high HER activity.

Highly Efficient Oxygen Reduction N-Doped Carbon Nanosheets Were Prepared by Hydrothermal Carbonization

A metal-free carbon catalyst is a kind of oxygen reduction catalyst with great prospects. It is an important material with potential to replace the traditional Pt catalyst. In this paper, a kind of irregular and ultra-thin carbon nanosheet (K180M-300-900) with high catalytic activity was synthesized by hydrothermal calcination using okra as a biomass and NH4Cl as an N source. The prepared nitrogen-doped metal-free catalyst with high pyridine-N and graphitic-N provides an extremely large number of active sites and has certain lattice defects. Ultra-thin carbon nanosheets promote sufficient contact between the catalyst and electrolyte, promote the diffusion of oxygen, and result in a faster transfer rate of electrons. The initial potential and half-slope potential of K180M-300-900 are 0.99 V and 0.82 V, respectively, which are comparable to those of 20% Pt/C. In addition, the stability and methanol tolerance of this catalyst (K180M-300-900) are better than 20% Pt/C, so it has great development potential and application value. This result provides a new method to prepare metal-free carbon materials that will take the place of traditional Pt catalysts.

Modulating the electronic structures of cobalt-organic frameworks for efficient electrocatalytic oxygen evolution

The oxygen evolution reaction (OER) is a key process in various energy storage/generation technologies. Tuning the electronic structures of catalysts is an effective approach to improve the catalyst's activity. In this work, we synthesized Ce-doped cobalt-organic frameworks with benzene-1, 4-dicarboxylic acid (BDC) as the ligand as efficient OER electrocatalysts (denoted as Co3Ce1 BDC) with excellent stability and improved catalytic performance. The introduced Ce in Co3Ce1 BDC changes the surface configuration and tunes electronic structures of the active Co site, leading to enhanced interaction between intermediates and catalysts. Besides, the specific surface area, reaction kinetics, charge transfer efficiency, and turnover frequency are also improved in the presence of Ce. As a result, the Co3Ce1 BDC demonstrated excellent performance with a low overpotential of 285 mV at a current of 10 mA·cm-2, a preferable Tafel slope of 56.1 mV·dec-1, and an excellent durability in 1 M KOH, indicating the potential for practical applications in water splitting and other energy storage technologies wherein the OER plays a critical role. Comprehensive theoretical calculations and modeling further identified the key role of Ce in modulating the electronic structure and OER activity of cobalt-organic frameworks. Most importantly, this work provides a new strategy to the development of efficient cobalt-organic framework catalysts in OER-related applications.

Interface engineering induced charge rearrangement boosting reversible oxygen electrocatalysis activity of heterogeneous FeCo-MnO@N-doped carbon nanobox

The advancement of bifunctional oxygen catalysts for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) is imperative yet challenging for the optimization of Zn-air batteries. In this study, we reported the successful incorporation of a novel Mott-Schottky catalytic site within a MnO-FeCo heterojunction into an N-doping carbon nanobox, taking into consideration the effects of the intrinsic electric field and hollow/porous support carriers for electrocatalyst design. As expected, the resulting heterogeneous catalyst exhibited an encouraging half-wave potential of 0.88 V and an impressive limiting-current density of 5.62 mA/cm2 for the ORR, as well as a minimal overpotential of 271 mV at 10 mA/cm2 for the OER, both in alkaline conditions. Furthermore, the Zn-air battery constructed with the heterojunction nanobox product displayed a decent potential gap of 0.621 V, an outstanding power density of 253 mW/cm2, a considerable specific capacity of 761 mAh/gZn, and exceptional stability, with up to 336 h of cycling charging and discharging operation. Consequently, this method of modulating the catalyst's surface charge distribution through an internal electric field at the interface and facilitating mass transport offers a novel avenue for the development of robust bifunctional oxygen catalysts.

In situ growth of surface-reconstructed aluminum fluoride nanoparticles on N, F codoped hierarchical porous carbon nanofibers as efficient ORR/OER bifunctional electrocatalysts for rechargeable zinc-air batteries

Modified porous carbon fibers have emerged as crucial electrocatalytic materials for zinc-air battery (ZAB) systems. However, most methods for preparing porous carbon fibers are complex and exhibit single functionality and poor catalytic activity, which hinders the development of ZABs. In this study, we design and synthesize a novel type of N, F codoped hierarchical porous carbon fiber with in situ growth of aluminum fluoride nanoparticles (AlF3@HPCNFs) through electrospinning and high-temperature carbonization. The N, F codoping effectively adjusts the charge density of neighboring carbon atoms and introduces additional active sites. Furthermore, the catalytic process induces surface reconstruction of AlF3 nanoparticles, allowing for their full exposure to the liquid electrolyte and accelerated catalytic reactions. Additionally, this interconnected hierarchical porous structure accelerates mass transfer at the oxygen/carbon-based substrate/electrolyte three-phase interfaces, thereby enhancing reaction kinetics and the accessibility of catalytic active sites, ultimately improving the utilization efficiency of these sites. Consequently, the AlF3@HPCNFs catalyst exhibits excellent bifunctional performance with a narrow potential difference (△E = 0.67 V). Moreover, the obtained bifunctional electrocatalyst is utilized for rechargeable ZABs, surpassing commercially available Pt/C + RuO2 cells in terms of high specific capacity (796 mAh gzn-1) and outstanding cycling stability (over 500 h). This research demonstrates the potential of AlF3@HPCNFs as a bifunctional electrocatalyst and introduces a simplified and effective method for the fabrication of metal fluoride-modified and hierarchically porous carbon nanofibers for rechargeable ZABs.

FeCo alloy entrapped in N-doped graphitic carbon nanotubes-on-nanosheets prepared by coordination-induced pyrolysis for oxygen reduction reaction and rechargeable Zn-air battery

Oxygen reduction reaction (ORR) on cathode severely suffers from sluggish kinetics in zinc-air batteries. Therefore, substantial efforts have been made to prepare advanced electrocatalysts for facilitating the ORR. Herein, we synthesized FeCo alloyed nanocrystals entrapped in N-doped graphitic carbon nanotubes on nanosheets (FeCo-N-GCTSs) by 8-aminoquinoline coordination-induced pyrolysis, whose morphology, structures, and property were characterized in details. Impressively, the obtained FeCo-N-GCTSs catalyst showed a positive onset potential (E_onset = 1.06 V) and half-wave potential (E_1/2 = 0.88 V), revealing excellent ORR activity. Further, the FeCo-N-GCTSs assembled zinc-air battery displayed the maximum power density of 133 mW cm^-2 and negligible gap change in the discharge-charge voltage plot over 288 h (ca. 864 cycles) at 5 mA cm^-2, outperforming the Pt/C + RuO₂ based counterpart. This work provides a facile route for construction of high-efficiency, durable and low-cost nanocatalysts for the ORR in fuel cells and rechargeable Zn-air batteries.

N-Doped Carbon Nanotubes Supported Fe-Mn Dual-Single-Atoms Nanozyme with Synergistically Enhanced Peroxidase Activity for Sensitive Colorimetric Detection of Acetylcholinesterase and Its Inhibitor

Monitoring acetylcholinesterase (AChE) and its inhibitors is of importance for early diagnosis and therapy of neurological diseases. Herein, N-doped carbon nanotubes supported Fe-Mn dual-single-atoms (FeMn DSAs/N-CNTs) were fabricated by a simple pyrolysis, as thoroughly figured out by a series of the characterization techniques. The peroxidase-like activity of FeMn DSAs/N-CNTs was investigated by catalytic oxidation of 3,3',5,5'-tetramethylbenzidine (TMB) to generate rich hydroxyl radicals (·OH) in the H₂O₂ system, which effectively catalyzed colorless TMB oxidation to blue oxidized TMB (ox-TMB). Besides, the peroxidase-like activity was greatly weakened by thiocholine (derived from AChE), accompanied by making blue ox-TMB fade. Impressively, the highly improved peroxidase-like property is further evidenced by density functional theory (DFT) calculations, where the dual-single atoms show a lower energy barrier (0.079 eV) and their interactions with the N-CNTs played critical roles for producing the oxygen radicals. By virtue of the nanozyme, a low-cost, specific, and sensitive colorimetric sensor was built for detection of AChE with a broader linear range of 0.1-30 U L^-1 and a lower limit of detection (LOD, 0.066 U L^-1), combined with its feasible analysis in human serum samples. Also, this platform was applied for measuring huperzine A inhibitor with a wide linear scope of 5-500 nM and a LOD down to 4.17 nM. This strategy provides a low-cost and convenient approach for early clinical diagnosis and drug development.

Lignin-derived iron carbide/Mn, N, S-codoped carbon nanotubes as a high-efficiency catalyst for synergistically enhanced oxygen reduction reaction and rechargeable zinc-air battery

Design of efficient and durable oxygen reduction reaction (ORR) electrocatalysts still remains challenge in sustainable energy storage and conversion devices. To achieve sustainable development, it is of importance to prepare high-quality carbon-derived ORR catalysts from biomass. Herein, Fe₅C₂ nanoparticles (NPs) were facilely entrapped in Mn, N, S-codoped carbon nanotubes (Fe₅C₂/Mn, N, S-CNTs) by a one-step pyrolysis of the mixed lignin, metal precursors and dicyandiamide. The resulting Fe₅C₂/Mn, N, S-CNTs had open and tubular structures, which exhibited positive shifts in the onset potential (E_onset = 1.04 V) and high half-wave potential (E_1/2 = 0.85 V), showing excellent ORR characteristics. Further, the typical catalyst-assembled Zn-air battery showed a high power density (153.19 mW cm^-2) and good cycling performance as well as obvious cost advantage. The research provides some valuable insights for rational construction of low-cost and environmentally sustainable ORR catalysts in clean energy field, coupled by offering some valuable insights for reusing biomass wastes.

Ni3S2/Co9S8 embedded poor crystallinity NiCo layered double hydroxides hierarchical nanostructures for efficient overall water splitting

Nickel-cobalt bimetallic layered double hydroxides (NiCo LDHs) are potential electrocatalysts with high performance and stability for overall water-splitting. However, its weak conductivity limits its practical applications. Herein, a simple hydrothermal in-situ conversion strategy is employed for constructing the novel heterogeneous electrocatalyst of Ni₃S₂/Co₉S₈ embedded poor crystallinity (Pc) NiCo LDH nanosheet arrays grown on the Ni foam (Pc-NiCo LDH/ Ni₃S₂/Co₉S₈), which can improve the conductivity via regulating the crystallinity. The crystallinity of NiCo LDH is well regulated by adjusting the amount of sulfur source, and the construction of Ni₃S₂/Co₉S₈ heterostructure exposes more active sites, improves the electrical conductivity, enhances the electronic interaction between NiCo LDH and Ni₃S₂/Co₉S₈, and significantly promotes the kinetics of water splitting. The optimized Pc-NiCo LDH/Ni₃S₂/Co₉S₈ hierarchical structure as both the anode and cathode exhibit the overall water splitting performance with the cell voltage of only 1.744 V to achieve the current density of 50 mA cm^-2 in the alkaline media and shows the competitive H₂ and O₂ production rate of 6.4 and 3.1 μL s^-1, respectively, suggesting its potential practical applications. This work provides a novel idea for the design of multiphase composite electrocatalysts applied in water splitting.

Caffeine derived graphene-wrapped Fe3C nanoparticles entrapped in hierarchically porous FeNC nanosheets for boosting oxygen reduction reaction

It is a vital requirement to explore high-efficiency and stable electrocatalysts for oxygen reduction reaction (ORR) to further relieve energy depletion. However, it is a critical challenge to develop low cost and high-quality carbon-based catalysts. Herein, a caffeine chelation-triggered pyrolysis approach was developed to construct graphene-wrapped Fe₃C nanoparticles incorporated in hierarchically porous FeNC nanosheets (G-Fe₃C/FeNC). The present Fe salt and its content as well as the pyrolysis temperature were carefully investigated in the control groups. The G-Fe₃C/FeNC catalyst showed a more positive onset potential (E_onset = 1.09 V) and half-wave potential (E_1/2 = 0.88 V) in a 0.1 M KOH solution, which outperformed commercial Pt/C (E_1/2 = 0.83 V, E_onset = 0.95 V), showing the excellent catalytic performance for the ORR activity, coupled with remarkable stability (only 0.18 mV negative shift in E_1/2 after 2000 cycles). This work provides some valuable insights for developing advanced electrocatalysts for energy storage and conversion related research.

Transition metal chalcogenides carbon-based as bifunctional cathode electrocatalysts for rechargeable zinc-air battery: An updated review

The rechargeable alkaline aqueous zinc-air batteries (ZABs) are prospective candidates to supply the energy demand for their high theoretical energy density, inherent safety, and environmental friendliness. However, their practical application is mainly restricted by the unsatisfactory efficiency of the air electrode, leading to an intense search for high-efficient oxygen electrocatalysts. In recent years, the composites of carbon materials and transition metal chalcogenides (TMC/C) have emerged as promising alternatives because of the unique properties of these single compounds and the synergistic effect between them. In this sense, this review presented the electrochemical properties of these composites and their effects on the ZAB performance. The operational fundamentals of the ZABs were described. After elucidating the role of the carbon matrix in the hybrid material, the latest developments in the ZAB performance of the monometallic structure and spinel of TMC/C were detailed. In addition, we report topics on doping and heterostructure due to the large number of studies involving these specific defects. Finally, a critical conclusion and a brief overview sought to contribute to the advancement of TMC/C in the ZABs.

Plasmon-Mediated Oxidase-like Activity on Ag@ZnS Heterostructured Hollow Nanowires for Rapid Visual Detection of Nitrite

Rational design of fast and sensitive determination of nitrite (NO₂^-) from a complicated actual sample overtakes a crucial role in constructing a high-efficiency sensing platform. Herein, a visual NO₂^- sensing platform with outstanding selectivity, sensitivity, and stability based on a surface plasmon resonance (SPR)-enhanced oxidase-like activity has been proposed. Benefiting from the intrinsic photocatalytic activity and limited light penetration of ZnS, the oxidase-like activity based on ZnS decorated on Ag nanowires (Ag@ZnS) is determined. It is demonstrated that the electrons are generated efficiently on the surface of ZnS and then transferred into the hot electrons of Ag with the help of localized SPR excitation, thus greatly oxidating the colorless 3,3',5,5'-tetramethylbenzidine (TMB) to produce dark blue oxidized TMB (oxTMB). When nitrite is added into the reaction system, the oxTMB will selectively react with NO₂^- to generate diazotized oxTMB, leading to a visual color change from dark blue to light green and subsequently to dark yellow. Owing to the specific recognition between nitrite and oxTMB, the recovery of catalytic activity induced an enhanced colorimetric test with a wider linear range for NO₂^- determination, an ultralow detection limit of 0.1 μM, excellent selectivity, and practicability for application in real samples. This plasmon-enhanced oxidase-like activity not only provides a smart approach to realize a colorimetric assay with high sensitivity and simplicity but also modulates oxidase-like activities.

Research Progress of Bifunctional Oxygen Reactive Electrocatalysts for Zinc-Air Batteries

Zinc-air batteries (ZABs) have several advantages, including high energy density, cheap price and stable performances with good application prospects in the field of power batteries. The charging and discharging reactions for the air cathode of ZABs are the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER), respectively, which play an important role in the whole performance of ZAB. Due to the cost and limited reserves of highly active precious metal catalysts, it is crucial to design alternative efficient and stable dual-functional non-precious metal catalysts. In the present review, we present a systematic summary of the recent progress in the use of transition metal-based electrocatalysts as alternatives to precious metals for the positive poles of ZAB air. Combined with state-of-the-art in situ characterization technologies, a deep understanding of the catalytic mechanism of OER/ORR provided unique insights into the precise design of excellent synthetic non-precious metal catalysts from the perspective of atomic structure. This review further shows that the hybrid electric battery is a new strategy to improve the efficiency of the hybrid electric battery, which could be available to alleviate the problem of resource shortage. Finally, the challenges and research trends for the future development of ZABs were clearly proposed.

3D porous carbon conductive network with highly dispersed Fe-Nxsites catalysts for oxygen reduction reaction

Intrinsic activity and reactive numbers are considered two important factors in oxygen reduction reaction (ORR) catalysts. Herein, we report the rational design and synthesis of a strongly coupled hybrid material comprising of FeZn nanoparticles (FeZn NPs) supported by a three-dimensional carbon conductive network (FeZn NPs@3D-CN) for increased ORR performance. Fe-N-C sites can offer high intrinsic activity owing to the unique bonding and oxygen vacancies, and the carbon conductive network facilitating the exposure to active sites, and increasing electron transport. Because of the synergetic effect of the conductive networks containing Fe-N-C and polyaniline, the catalysts exhibited ORR activity in an alkaline medium via a four-electron transfer process. FeZn NPs@3D-CN exhibited outstanding performance with a limited current density (6.2 mA cm^-2), the Tafel slope (81.19 mV dec^-1), and stability (23 mV negative shift after 2000 cycles), which were superior to those of 20% Pt/C (5.7 mA cm^-2, 75.1 mV dec^-1, 36 mV negative shift after 2000 cycles). This research highlights the effect of conductive networks expanding pathways and reducing the resistance of mass transport, which is a facile method to generate superior ORR electrocatalysts.

Cobalt phosphide nanoparticles encapsulated in manganese, nitrogen co-doped porous carbon nanosheets with rich nanoholes for high-efficiency oxygen reduction reaction

It is a challenging task to research oxygen reduction electrocatalysts with cost-effectiveness, high-performance and ultra-stability to replace traditional noble metal catalysts in renewable energy conversion/storage devices. Herein, cobalt phosphide (Co₂P) nanoparticles encapsulated in Mn, N co-doped porous carbon nanosheets with abundant nanoholes (Co₂P/Mn,N-PCNS) were prepared by a alizarin complexone coordination regulated pyrolysis at 800 °C. In the controlled experiments, the pyrolysis temperature and metal types were investigated in details. The resultant catalyst exhibited rapid mass/charge transfer and superior oxygen reduction reaction (ORR) performance (E_onset = 0.96 V; E_1/2 = 0.86 V vs RHE), surpassing commercial Pt/C. This work presents some constructive guidelines for synthesis of appealing ORR electrocatalysts in renewable energy technology.

Enhancing the bifunctional activity of CoSe2 nanocubes by surface decoration of CeO2 for advanced zinc-air batteries

The coupling of oxygen evolution and reduction reactions (OER and ORR) plays a key role in rechargeable Zn-air batteries (ZABs). However, both OER and ORR still suffer from sluggish kinetics, even when using the mainstream precious metal-based catalysts. Herein, oxygen vacancies-rich CeO₂ decorated CoSe₂ nanocubes are proposed as a novel air electrode to drive OER and ORR for ZABs. The resultant CeO₂ coupled CoSe₂ nanocubes (CeO₂@CoSe₂-NCs) catalyst exhibits a significantly enhanced bifunctional activity relative to the pristine CoSe₂-NCs and the pristine CeO₂. Moreover, an assembled ZABs using this CeO₂@CoSe₂-NCs electrode delivers a high output power density of 153 mW cm^-2 and a long-life stability over 400 cycles, superior to the benchmark Pt/C-IrO₂ electrode. Theoretical calculations reveal that the electronic interaction and oxygen vacancies in CeO₂@CoSe₂-NCs contribute to efficient oxygen electrocatalysis. This protocol provides a promising approach of constructing oxygen vacancies in hybrid catalysts for energy conversion and storage devices.

ZnS modified N, S dual-doped interconnected porous carbon derived from dye sludge waste as high-efficient ORR/OER catalyst for rechargeable zinc-air battery

Facile and rational design of high-efficient oxygen reduction reaction (ORR)/oxygen evolution reaction (OER) bifunctional electrocatalysts is significant for rechargeable Zinc-air batteries. In this study, ZnS modified N, S dual-doped interconnected porous carbon (ZnS/NSC) derived from the dye sludge waste is successfully fabricated via a facile ZnCl₂-assisted pyrolysis process. The effect of ZnCl₂ and carbonization temperature on the microstructure and electrocatalytic performance is systematically investigated. By virtue of the synergistic effect between ZnS nanoparticles and N, S dual-doped porous carbon network, the obtained catalyst ZnS/NSC calcined at 1000 °C exhibits a decent bifunctional electrocatalytic performance with potential gap (ΔE=E_OER,10-E_ORR,1/2) of 0.76 V comparable with commercial electrocatalysts (Pt/C and RuO₂). In addition, a rechargeable zinc-air battery employed ZnS/NSC-1000 as the air cathode also displays the favorable electrochemical performance, in which the power density is 125 mW cm^-2, the specific capacity is 763.27 mAh g^-1 and the cycling stability at 10 mA cm^-2 is more than 85 h, indicating a promising application prospect in rechargeable Zinc-air batteries.

Metal organic framework derived perovskite/spinel heterojunction as efficient bifunctional oxygen electrocatalyst for rechargeable and flexible Zn-air batteries

Interface engineering strategy has been developed to design efficient catalysts for boosting electrocatalytic performance in past few decades. Herein, heterojunctions of PrCoO₃/Co₃O₄ nanocages (PCO/Co₃O₄ NCs) with atomic-level engineered interfaces and rich oxygen vacancies are proposed for Zn-air batteries. The synthesized product shows exceptional bifunctional activity and robust stability towards oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). The enhanced catalytic capacity is primary attributed to the synergistic effect of PCO/Co₃O₄, evidenced by the experimental results and theoretical calculations. More importantly, the PCO/Co₃O₄ NCs assembled liquid Zn-air battery exhibits a power density of 182 mW cm^-2 and a long-term operation of 185 h. When assembled into solid-state cable type battery, this newly designed catalyst also reaches a stable open circuit voltage (1.359 V) and a peak power density of 85 mW cm^-3. Our findings provide essential guidelines of engineering heterostructured electrocatalysts for future wearable electronic devices.

Three-dimensional self-supporting superstructured double-sided nanoneedles arrays of iron carbide nanoclusters embedded in manganese, nitrogen co-doped carbon for highly efficient oxygen reduction reaction

Nitrogen- and transition metal-dual doped carbon materials with low cost and high catalytic performances are considered as one of promising alternatives for noble metal catalysts in acceleration of oxygen reduction reaction (ORR). In this work, three-dimensional (3D) self-supporting superstructures of iron carbide (Fe₃C) nanoclusters entrapped in manganese (Mn)- and nitrogen (N)-dual doped carbon nanosheets covered with double-sided nanoneedles carbon arrays (Fe₃C/Mn,N-NCAs) are simply synthesized by a coordination pyrolysis method, in which dicyandiamide mainly behaves as nitrogen source and 1-(2-pyridylazo)-2-naphthol (PAN) as carbon source. Integration of the unique 3D self-supporting superstructures and synergistic effects of the multi-compositions, the as-obtained catalyst displays appealing ORR performance such as the much positive onset potential (E_onset = 0.98 V vs. RHE) and half-wave potential (E_1/2 = 0.88 V vs. RHE), as well as a just 10 mV negative shift in E_1/2 after 2000 cycles, surpassing commercial Pt/C. This work provides some valuable perspectives for preparation of high-efficiency and low-cost non-noble metal ORR electrocatalysts in energy transformation and storage correlated systems.

Integrating Bimetal Alloy into N-Doped Carbon Nanotubes@Nanowires Superstructure for Zn-Air Batteries

Exploring bifunctional oxygen electrocatalysts with low cost and high performance is critical to the development of rechargeable zinc-air batteries, but it still remains a huge challenge. In this work, a "coordination construction-pyrolysis/self-catalyzed growth" approach was employed to fabricate branches@trunks-like, N-doped carbon nanotubes@nanowires superstructure with uniformly incorporated CoFe alloy nanoparticles (CoFe@CNTs-NWs). The rational design of such hierarchical architecture could effectively enlarge the exposure of active sites, modulate their electronic structure, and assist the electron transfer and mass diffusion, thus benefiting both ORR and OER. The resultant CoFe@CNTs-NWs displayed prominent bifunctional electrocatalytic activity and stability with a minimized oxygen overpotential of 0.71 V. When used as a cathode for zinc-air batteries, it provided a high peak power density of 131 mW cm^-2 and remarkable charge-discharge stability for at least 400 cycles (130 h). This study presents a successful demonstration for optimizing the electrocatalytic performance by elaborate nanostructure and carbon matrix hybridization with simultaneous modulation of electronic structure, thus providing a new avenue to the rational design of transition metal-based oxygen electrocatalysts.

Well entrapped platinum-iron nanoparticles on three-dimensional nitrogen-doped ordered mesoporous carbon as highly efficient and durable catalyst for oxygen reduction and zinc-air battery

The high-performance and durable oxygen reduction reaction (ORR) catalyst on air cathode is a key component in assembly of Zn-air batteries. Herein, three-dimensional N-doped ordered mesoporous carbon (3D N-OMC) was first prepared with silica as a template via pyrolysis with assistance of dicyandiamide as a N-doping agent, combined by full adsorption of platinum (II) acetylacetonate (Pt(acac)₂) and iron (II) phthalocyanine (FePc) via π-π interactions. After further pyrolysis of the resulting mixture, many PtFe nanoparticles were efficiently incorporated in 3D N-OMC (termed as PtFe@3D N-OMC for simplicity). Control experiments were certificated the important role of the pyrolysis temperature played in this synthesis. The resultant composite synergistically combines advantages of hierarchically accessible surfaces, highly open structure, and well-dispersed PtFe particles, which endow the PtFe@3D N-OMC with onset and half-wave potentials of 0.98 and 0.86 V in alkaline media, respectively, showing appealing catalytic activity for the ORR. Most significantly, the PtFe@3D N-OMC based Zn-air battery has a high power density of 80.57 mW cm^-2 and long-term durability (220 h, 660 cycles). This work opens a new avenue for design of high-efficiency and durable ORR electrocatalysts in energy conversion and storage systems.

Electronic Regulation of ZnCo Dual-Atomic Active Sites Entrapped in 1D@2D Hierarchical N-Doped Carbon for Efficient Synergistic Catalysis of Oxygen Reduction in Zn-Air Battery

Transition metal-based nitrogen-doped carbon (M-N_x -C) is considered as a promising catalyst for the oxygen reduction reaction (ORR) in clean energy storage and conversion devices. Herein, ZnCo dual-atomic sites are incorporated in hierarchical N-doped carbon (HNC), with 1D nanotubes wrapped in 2D nanosheets structure (termed as 1D@2D ZnCo-HNC), via a one-step bio-inspired pyrolysis. The feeding ratio of Zn to Co precursor and pyrolytic temperature are critically modulated to achieve well-defined morphologies of the products, endowing them with the integrated merits of nanotubes and nanosheets as efficient ORR catalysts. Benefiting from the particular structure and electronic regulation of Zn on Co, the ZnCo-N_x dual-atomic system exhibits excellent ORR catalytic characteristics with an onset potential of 1.05 V and a half-wave potential of 0.82 V. Density functional theory calculations further explain the regulating role of Zn, such that the adjusted Co in ZnCo-N_x sites significantly reduces the energy cost to ultimately facilitate the ORR. Moreover, the Zn-air battery assembled with ZnCo-HNC is capable of delivering the maximum power density of 123.7 mW cm^-2 and robust stability for 110 h (330 cycles). This method provides a promising strategy for fabricating efficient transition metal-based carbon catalysts for green energy devices.

Carbon quantum dots with blue/near infrared emissions for ratiometric fluorescent lornoxicam sensing and bio-imaging

An economical and eco-friendly hydrothermal method for the preparation of nitrogen-doped carbon quantum dots (N-CQDs) was studied with rambutan peel and lysine. The morphology, structure, and optical properties of N-CQDs were characterized by transmission electron microscopy, Fourier transform infrared spectrometry, X-ray powder diffractometer, X-ray photoelectron spectrometry, and UV spectrophotometry. The synthesized N-CQDs have excellent characteristics such as strong fluorescence, good dispersion, high stability, and excellent water solubility. The absolute fluorescence quantum yield is 1.02%, the average particle size is 1.63 nm, and the maximum excitation wavelength is 340 nm. The maximum emission wavelengths are 430 nm and 800 nm. As a quencher, lornoxicam (LNX) was used to quench the fluorescence of N-CQDs with the mechanism of inner filter effect. The fluorescence ratio of N-CQDs (F₄₃₀/F₈₀₀) shows a good linear relationship to the concentration of LNX. The linear range and the detection limit of LNX are 0.01‒100 and 0.003 μmol/L, respectively. An effective ratiometric fluorescence probe for the detection of LNX was constructed. The method has the advantages of low detection limit, high sensitivity, wide linear range, and can be applied to the determination of LNX in real samples. Moreover, according to the excitation-dependent fluorescence behavior, dual-wavelength emission, and biocompatibility of N-CQDs, it has been applied to cell imaging.

Label-free electrochemical biosensor for determination of procalcitonin based on graphene-wrapped Co nanoparticles encapsulated in carbon nanobrushes coupled with AuPtCu nanodendrites

A new label-free electrochemical immunosensor was constructed for quantitative detection of procalcitonin (PCT), by employing AuPtCu nanodendrites (AuPtCu NDs, prepared by a one-pot solvothermal method) and graphene-wrapped Co nanoparticles encapsulated in 3D N-doped carbon nanobrushes (G-Co@ NCNBs), obtained by self-catalyzed chemical vapor deposition as immune-sensing platform. Impressively, the home-made nanocomposite enlarged the highly accessible active sites and promoted the mass/electron transport, in turn showing the efficient synergistic catalysis towards H₂O₂ reduction, combined by greatly increasing the loading capacity of the PCT antibody (Ab). The as-constructed sensor displayed a dynamic linear range of 0.0001 ~ 100 ng mL^-1 along with an ultra-low limit of detection (LOD = 0.011 pg mL^-1, S/N = 3) and was further explored for determination of PCT in a diluted serum sample with acceptable results. The sensor provides some valuable guidelines for bioassay and early diagnosis of sepsis.

Novel Aggregation-Enhanced PEC Photosensitizer Based on Electrostatic Linkage of Ionic Liquid with Protoporphyrin IX for Ultrasensitive Detection of Molt-4 Cells

Nowadays, aggregation quenching of most organic photosensitizers in aqueous media seriously restricts analytical and biomedical applications of photoelectrochemical (PEC) sensors. In this work, an aggregation-enhanced PEC photosensitizer was prepared by electrostatically bonding protoporphyrin IX (PPIX) with an ionic liquid of 1-butyl-3-methylimidazole tetrafluoroborate ([BMIm][BF₄]), termed as PPIX-[BMIm] for clarity. The resultant PPIX-[BMIm] showed weak photocurrent in pure dimethyl sulfoxide (DMSO, good solvent), while the PEC signals displayed a 44.1-fold enhancement in a water (poor solvent)/DMSO binary solvent with a water fraction (f_w) of 90%. Such PEC-enhanced mechanism was critically studied by electrochemistry and density functional theory (DFT) calculation in some detail. Afterward, a label-free PEC cytosensor was built for ultrasensitive bioassay of acute lymphoblastic leukemia (molt-4) cells by electrodepositing Au nanoparticles (Au NPs) on the PPIX-[BMIm] aggregates and sequential assembly of protein tyrosine kinase (PTK) aptamer DNA (aptDNA). The resultant cytosensor showed a wide linear range (300 to 3 × 10⁵ cells mL^-1) with a limit of detection (LOD) as low as 63 cells mL^-1. The aggregation-enhanced PEC performance offers a valuable and practical pathway for synthesis of advanced organic photosensitizer to explore its PEC applications in early diagnosis of tumors.

Ultrasensitive photoelectrochemical aptasensor for detecting telomerase activity based on Ag2S/Ag decorated ZnIn2S4/C3N4 3D/2D Z-scheme heterostructures and amplified by Au/Cu2+-boron-nitride nanozyme

Enzyme-mediated signal amplification strategies have gained substantial attention in photoelectrochemical (PEC) biosensing, while natural enzyme on the photoelectrode inevitably obstructs the interfacial electron transfer, in turn deteriorating the photocurrent responses. Herein, Au nanoparticles and Cu²⁺-modified boron nitride nanosheets (AuNPs/Cu²⁺-BNNS) behaved as nanozyme to achieve remarkable magnification in the PEC signals from a novel signal-off aptasensor for ultra-sensitive assay of telomerase (TE) activity based on Ag₂S/Ag nanoparticles decorated ZnIn₂S₄/C₃N₄ Z-scheme heterostructures (termed as Ag₂S/Ag/ZnIn₂S₄/C₃N₄, synthesized by hydrothermal treatment). Specifically, telomerase primer sequences (TS) were extended by TE in the presence of deoxyribonucleoside triphosphates (dNTPs), which was directly bond with the thiol modified complementary DNA (cDNA), achieving efficient linkage with the nanozyme via Au-S bond. The immobilized nanoenzyme catalyzed the oxidation between 4-chloro-1-naphthol (4-CN) and H₂O₂ to generate insoluble precipitation on the photo-electrode. By virtue of the inhibited PEC signals with the TE-enabled TS extension, an aptasensor for assay of TE activity was developed, showing the wide linear range of 50-5×10⁵ cell mL^-1 and a low detection limit of 19 cell mL^-1. This work provides some valuable guidelines for developing advanced nanozyme-based PEC bioanalysis of diverse cancer cells.

A signal-off photoelectrochemical aptasensor for ultrasensitive 17β-estradiol detection based on rose-like CdS@C nanostructure and enzymatic amplification

Carbon-coated cadmium sulfide rose-like nanostructures (CdS@C NRs) were prepared via a facile solvothermal approach and used as the photoelectrochemical (PEC) sensing platform for the integration of functional biomolecules. Based on this, a novel "signal-off" PEC aptasensor mediated by enzymatic amplification was proposed for the sensitive and selective detection of 17β-estradiol (E2). In the presence of E2, alkaline phosphatase-modified aptamer (ALP-apta) were released from the electrode surface through the specific recognition with E2, which caused the negative effect on PEC response due to the decrease of ascorbic acid (AA) produced by the ALP in situ enzymatic catalysis. The developed PEC aptasensor for detection of E2 exhibited a wide linear range of 1.0-250 nM, with the low detection limit of 0.37 nM. This work provides novel insight into the design of potential phoelectroactive materials and the application of signal amplification strategy in environmental analysis field.

Catalytic oxidation of VOCs over 3D@2D Pd/CoMn2O4 nanosheets supported on hollow Al2O3 microspheres

Catalytic oxidation is a promising method for removing harmful volatile organic compounds (VOCs). Therefore, exploring high-efficiency catalysts for catalyzing VOCs is of great significance to the realization of an environment-friendly and sustainable society. Here, a series of 3D@2D constructed Al₂O₃@CoMn₂O₄ microspheres with a hollow hierarchical structure supporting Pd nanoparticles was successfully synthesized. The introduction of hollow Al₂O₃ for the in situ vertical growth of 2D CMO spinel materials constructs a well-defined core - shell hollow hierarchical structure, leading to larger specific surface area, more accessible active sites and promoted catalytic activity of support material. Additionally, theoretical calculations also indicate that the addition of Al₂O₃ as the support material strengthens the adsorption of toluene and oxygen on CoMn₂O₄, which promotes their activation. The dispersion of Pd further strengthens the low-temperature reducibility along with more active surface oxygen species and lower apparent activation energy. The optimum 1 wt% Pd/h-Al@4CMO catalyst possesses the lowest apparent activation energy for toluene of 77.4 kJ mol^-1, showing the relatively best catalytic activity for VOC oxidation, reaching 100% toluene, benzene, and ethyl acetate conversion at 165, 160, and 155 °C, respectively. Meanwhile, the 1 wt% Pd/h-Al@4CMO sample possesses excellent catalytic stability, outstanding selectivity, and good moisture tolerance, which is an effective candidate for eliminating VOCs contaminants.

Shape-controlled Mn–Fe PBA derived micromotors for organic pollutant removal

A new strategy is employed to prepare Mn–Fe PBA derived oxide micromotors with excellent motion performances through co-precipitation and heat treatment, which can be used for organic pollutant degradation with recycling and reusing advantages.

N, S-doped hollow carbon nanosheet encapsulated Co9S8 nanoparticles as high-efficient bifunctional electrocatalyst for rechargeable zinc-air battery

The development of non-noble metal-based oxygen reduction/evolution reaction (ORR/OER) bifunctional electrocatalyst with reasonably designed structure and inexpensive component is of practical significance for commercialization of rechargeable zinc-air batteries. Here, we...

Hydrogen Bond Organic Frameworks as a Novel Electrochemiluminescence Luminophore: Simple Synthesis and Ultrasensitive Biosensing

Nowadays, continuous efforts have been devoted to searching highly efficient electrochemiluminescence (ECL) emitters for applications in clinical diagnosis and food safety. In this work, triazinyl-based hydrogen bond organic frameworks (Tr-HOFs) were synthesized by N···H hydrogen bond self-assembly aggregation, where 6,6'-(1,4-phenylene)bis(1,3,5-triazine-2,4-diamine) (phenyDAT) was prepared via the cyclization reaction and behaved as a novel ligand. Impressively, the resulting Tr-HOFs showed strong ECL responses with highly enhanced ECL efficiency (21.3%) relative to the Ru(bpy)₃²⁺ standard, while phenyDAT hardly showed any ECL emission in aqueous phase. The Tr-HOFs innovatively worked as a new ECL luminophore to construct a label-free biosensor for assay of kanamycin (Kana). Specifically, the ECL response greatly weakened upon assembly of captured DNA with ferrocene (cDNA-Fc) onto the Tr-HOFs-modified electrode, while the ECL signals were adversely recovered by releasing linked DNA (L-DNA) from double-stranded DNA (dsDNA, hybridization of aptamer DNA (aptDNA) with L-DNA) due to the specific recognition of Kana with the aptDNA combined by the linkage of L-DNA and cDNA-Fc on the electrode. The as-built sensor showed a broadened linear range (1 nM-10 μM) and a limit of detection (LOD) down to 0.28 nM, which also displayed satisfactory results in the analysis of Kana in the milk and diluted human serum samples. This work offers a novel pathway to design an ECL emitter with organic molecules, holding great promise in biomedical analysis and food detection.