Laboratory study of creosote removal from sand at elevated temperatures

Heat and mass transfer induced by alternating current during desorption of PAHs from soil using electrical resistance heating

The transfer of heat and contaminants by alternating current (AC) and the removal mechanism of polycyclic aromatic hydrocarbons (PAHs) in electrical resistance heating (ERH) need further study. The main factors affecting heat transfer and water evaporation in the ERH experiment were studied, and the desorption efficiency, temporal and spatial distribution and kinetic behavior under various conditions were analyzed. The results suggested that moisture content was a necessary condition to ensure effective heating of soil, and soil moisture content above 30% was recommended. Higher voltage intensity and/or ion concentration meant stronger input power, resulting in the rapider heating process and the shorter the boiling time. At a low desorption temperature (about 100°C), the Phe desorption mainly depended on the volatilization of surface Phe and the co-boiling of Phe-water. In ERH, the participation of AC would accelerate the diffusion of pollutants from the internal pores of soil particles and their redistribution with water phase, thus improving the Phe removed by co-boiling. It was noteworthy that AC just greatly promoted solid-liquid mass transfer, but it hardly promoted desorption directly, and the removal still depended on Phe-water co-boiling. The Phe desorption efficiency could be significantly improved from 14.0~18.4% to 59.6~70.8% under the combined action of current strengthening Phe diffusion and co-boiling. Thermogravimetric and product analysis confirmed that no new organic matter was generated, but only Phe entered the gas phase through phase change.

Understanding of Co-boiling between Organic Contaminants and Water during Thermal Remediation: Effects of Nonequilibrium Heat and Mass Transport

In situ thermal desorption (ISTD) provides an efficient solution to remediation of soil and groundwater contaminated with nonaqueous phase liquids (NAPLs). Establishing a relationship between the subsurface temperature rise and NAPL removal is significant to reduce energy consumption of ISTD. However, the co-boiling phenomenon between NAPL and water poses a great challenge in developing this relationship due to the nonequilibrium heat and mass transport effects. We performed a systematic experimental investigation into the local temperature rise patterns at different distances from a NAPL pool and under different degrees of superheat by selecting four representative NAPLs (i.e., trichloroethylene, tetrachlorethylene, n-hexane, and n-octane) according to their density and boiling point relative to water. The patterns of temperature rise indicated that the underground temperature field can be divided into three zones: the zone of local thermal equilibrium, the nonequilibrium zone affected by co-boiling, and the zone unaffected by co-boiling. We developed a pattern-recognition-based approach, which considers the effects of local heat and mass transport to establish a qualitative correlation between the temperature rise and NAPL removal. Our results give deeper insights into the understanding of subsurface temperatures in ISTD practice, which can serve as the guideline for more accurate and sustainable remediation.

Propylene glycol-mixed steam enhanced extraction for an efficient and sustainable remediation of PAHs-contaminated soil

An innovative thermal desorption method, propylene glycol (PG)-mixed steam enhanced extraction, is proposed for a highly efficient remediation of polycyclic aromatic hydrocarbons (PAHs)-contaminated soil. It is found that injecting PG-mixed steam into soil column could obtain > 99% removal efficiencies of PAHs either for the pyrene-spiked soil, or for the contaminated field soil with high-molecular-weight PAHs. PG is a safe and low-cost dihydric alcohol with a boiling point higher than water. When the PG-mixed steam penetrated the contaminated soil, the PG vapor preferentially condensed to form a hot liquid with concentrated PG (e.g., from 30 wt% PG in gas phase to 90 wt% PG in the liquid phase), which would significantly solubilize the PAHs and enhance their desorption from soils. The results also revealed that the effluents derived from the PG-mixed steam could be purified by removing the desorbed PAHs using a simple coagulation treatment, and the recovered PG solution could be reused. The plant assay using wheat seeds showed that the remediated soil had a good regreening potential. Our results demonstrate that PG-mixed steam injection is a promising thermal desorption method for an efficient and sustainable remediation of PAHs-contaminated soil.

Enhanced semi-volatile DNAPL accessibility at sub-boiling temperature during electrical resistance heating in heterogeneous porous media

Successful remediation of semi-volatile contaminants using electrical resistance heating (ERH) coupled technologies requires a deep understanding of contaminant migration and accessibility, especially with stratigraphic heterogeneity and dense nonaqueous phase liquid (DNAPL) occurrence. Here, we chose nitrobenzene (NB) as a model contaminant of semi-volatile DNAPL and uniquely demonstrated that temperature variation during ERH could induce NB DNAPL migration out of the low permeability zone (LPZ) even below water boiling temperature. When heating the system using alternating current (AC) of 140 V to a temperature range of 50-79 °C, obvious DNAPL migration was visually observed. The upward migration of DNAPL would considerably increase the mass of accessible contaminant by other remediation measures. The downstream cumulative NB mass of 1092 mg in 140 V system raised 56-folds compared to that of 19 mg in the control experiment with only groundwater flow. This migration was mainly attributed to a complex natural convection caused by temperature gradient. Comparing with traditional AC heating, ERH powered by pulsed direct current (PDC-ERH) showed a higher and more uneven heating pattern, resulting in a stronger convection at the same voltage that enhanced the DNAPL migration out of LPZ. These results revealed the importance of natural convection in the ERH process, which could be further optimized to improve the energy efficiency of remediation.

Ebullition-facilitated mobilization of trapped dense non-aqueous phase liquid at residual saturation from sandy sediments

Gas ebullition can mobilize dense non-aqueous phase liquids (DNAPLs) from sediments to the overlying water column, increasing the DNAPL-impacted area and posing serious challenges to the remediation and management of contaminated sediments. Despite this, there have been few laboratory studies focused on gas ebullition-facilitated transport of DNAPL. In this study, bubble-facilitated transport was investigated by injecting gas (air or nitrogen) at 1 mL/min through a creosote source zone (∼25% saturation) capped with sand layers of different thicknesses. Three short-term experiments (8.3-8.7 h) were capped with 11.4, 7.0 or 4.5 cm of sand to estimate DNAPL flux. One long-term experiment (30 days) was capped with 8 cm of sand to investigate DNAPL removal. Heptane placed on a layer of water above the sand was used as a solvent trap and analyzed for petroleum hydrocarbons (PHCs). Results showed that creosote travelled as thin coatings and films surrounding gas bubbles migrating out of the source zone. Gas invasion was dominated by capillarity in the 11.4 cm-thick sand layer and by fracturing in the 7.0 and 4.5 cm-thick sand layers. Migration through these fractures often led to the formation of creosote tails on mobilized bubbles that drained towards the rear end of the bubble. The mass released decreased exponentially with sand cap thickness. In the long-term experiment, images showed significant depletion of the source zone in 30 days. Linear regression analysis showed that relationships with high predictive capabilities for ebullition-facilitated fluxes of hydrophobic organic contaminants can be obtained by incorporating gas ebullition flux and source strength, based on results from this study along with others from the field and laboratory. To our knowledge, this is the first study to compile and integrate data collected from laboratory and field studies to develop an assessment tool to facilitate the management of contaminated sediments affected by gas ebullition.

Experimentally and spectroscopically evidenced mechanistic study of butyl peroxyacid oxidative degradation of benzo[a]pyrene in soil

Benzo[a]pyrene (BaP) is a major indicator of soil contamination and categorized as a highly persistent, carcinogenic, and mutagenic polycyclic aromatic hydrocarbon. An advanced peroxyacid oxidation process was developed to reduce soil pollution caused by BaP originating from creosote spills from railroad sleepers. The pH, organic matter, particle size distribution of soil, and concentrations of BaP and heavy metals (Cd, Cu, Zn, Pb, and As) in the BaP-contaminated soils were estimated. A batch experiment was conducted to determine the effects of organic acid type, soil particle size, stirring speed, and reaction time on the peroxyacid oxidation of BaP in the soil samples. Additionally, the effect of the organic acid concentration on the peroxyacid degradation of BaP was investigated using an oxidizing agent in spiked soil with and without hydrogen peroxide. The results of the oxidation process indicated that BaP and heavy metal residuals were below acceptable Korean standards. A significant difference in the oxidative degradation of BaP was observed between the spiked and natural soil samples. The formation of a peroxyacid intermediate was primarily responsible for the enhanced BaP oxidation. Further, butyric acid could be reused thrice without losing the efficacy (<90%). The systematic peroxyacid oxidative degradation mechanism of BaP was also discussed. A qualitative analysis of the by-products of the BaP reaction was conducted, and their corresponding toxicities were determined for possible field applications. The findings conclude that the developed peroxyacid oxidation method has potential applications in the treatment of BaP-contaminated soils.

Removal of trichloroethene from thin clay lenses by electrical resistance heating: Laboratory experiments and the effects of gas saturation

The removal of dissolved volatile organic compounds (VOCs) from low-permeability lenses is important to limit back diffusion at sites impacted by dense non-aqueous phase liquids (DNAPLs). In situ thermal treatment (ISTT) technologies have the potential to treat DNAPL-impacted sites by enhancing diffusion from low-permeability lenses during heating. A series of two-dimensional laboratory tank experiments was conducted to investigate heating, gas formation, and trichloroethene (TCE) removal from a clay lens surrounded by sand. Results showed preferential heating of the clay and substantial TCE removal, with post-heating relative concentrations less than 0.06. The extent of TCE removal was not explained by only an increase in the aqueous TCE diffusion coefficient with increased temperature. Modelling estimates based on 1D diffusion from the lens showed that diffusion through both gas and water phases was required to match observations. Gas formation in the interior of the lens was also indicated by measured changes in bulk electrical conductivity of the clay during cool down, with gas saturations estimated to be greater than 0.21 at the end of heating. These estimates were larger than those needed to match the observed removal by diffusion, and suggest that connected gas pathways were created in the lens during heating, but that not all of the gas produced was part of those pathways. These results suggest that ISTT technologies may be effective in removing dissolved VOCs from thin clay lenses, and that gas formation within the clay should be considered when predicting the extent and rate of removal.

Modification of the Bacterial Cell Wall—Is the Bioavailability Important in Creosote Biodegradation?

Creosote oil, widely used as a wood preservative, is a complex mixture of different polycyclic aromatic compounds. The soil contamination result in the presence of a specific microcosm. The presented study focuses on the most active strains involved in bioremediation of long-term creosote-contaminated soil. In three soil samples from different boreholes, two Sphingomonas maltophilia (S. maltophilia) and one Paenibacillus ulginis (P. ulginis) strain were isolated. The conducted experiments showed the differences and similarities between the bacteria strains capable of degrading creosote from the same contaminated area. Both S. maltophilia strains exhibit higher biodegradation efficiency (over 50% after 28 days) and greater increase in glutathione S-transferase activity than P. ulginis ODW 5.9. However, S. maltophilia ODW 3.7 and P. ulginis ODW 5.9 were different from the third of the tested strains. The growth of the former two on creosote resulted in an increase in cell adhesion to Congo red and in the total membrane permeability. Nevertheless, all three strains have shown a decrease in the permeability of the inner cell membrane. That suggests the complex relationship between the cell surface modifications and bioavailability of the creosote to microorganisms. The conducted research allowed us to broaden the current knowledge about the creosote bioremediation and the properties of microorganisms involved in the process.

A numerical model for estimating the removal of volatile organic compounds in laboratory-scale treatability tests for thermal treatment of NAPL-impacted soils

Treatability tests can be carried out to assess the potential effectiveness of thermal treatment technologies under different site conditions and are important for specific technology selection and design. In order to reduce the costs for laboratory tests and expand the insights from previous treatability studies, a one-dimensional (1D) radial finite difference model was developed to simulate the removal of volatile organic compounds (VOCs) in laboratory thermal treatability tests. The processes considered in the model include heat conduction, co-boiling of single-component or multi-component NAPLs with water, and water boiling. An explicit approach is used to simulate the evolution of NAPL composition for multi-component NAPLs during heating. The developed model adopts only two fitting parameters and was calibrated and validated using previous laboratory experiments. In this paper, the developed model was first calibrated to three laboratory experiments using temperature measurements, which resulted in matches to the NAPL and gas saturations. After calibration, the model was able to predict the temperature, NAPL and gas saturations for the remaining seven experiments, including those with single and multi-component NAPLs, using the average value of each fitting parameter.