Self-assembled monolayers of 6-mercapto-1-hexanol and mercapto-n-hexyl-poly(dT)18-fluorescein on polycrystalline gold surfaces: An electrochemical impedance spectroscopy study

Evaluation of Polytyramine Film and 6-Mercaptohexanol Self-Assembled Monolayers as the Immobilization Layers for a Capacitive DNA Sensor Chip: A Comparison

The performance of a biosensor is associated with the properties of an immobilization layer on a sensor chip. In this study, gold sensor chips were modified with two different immobilization layers, polytyramine film and 6-mercaptohexanol self-assembled monolayer. The physical, electrochemical and analytical properties of polytyramine film and mercaptohexanol self-assembled monolayer modified gold sensor chips were studied and compared. The study was conducted using atomic force microscopy, cyclic voltammetry and a capacitive DNA-sensor system (CapSenze™ Biosystem). The results obtained by atomic force microscopy and cyclic voltammetry indicate that polytyramine film on the sensor chip surface possesses better insulating properties and provides more spaces for the immobilization of the capture probe than a mercaptohexanol self-assembled monolayer. A capacitive DNA sensor hosting a polytyramine single-stranded DNA-modified sensor chip displayed higher sensitivity and larger signal amplitude than that of a mercaptohexanol single-stranded DNA-modified sensor chip. The linearity responses for polytyramine single-stranded DNA- and mercaptohexanol single-stranded DNA-modified sensor chips were obtained at log concentration ranges, equivalent to 10^-12 to 10^-8 M and 10^-10 to 10^-8 M, with detection limits of 4.0 × 10^-13 M and 7.0 × 10^-11 M of target complementary single-stranded DNA, respectively. Mercaptohexanol single-stranded DNA- and polytyramine single-stranded DNA-modified sensor chips exhibited a notable selectivity at an elevated hybridization temperature of 50 °C, albeit the signal amplitudes due to the hybridization of the target complementary single-stranded DNA were reduced by almost 20% and less than 5%, respectively.

The application of DNA polymerases and Cas9 as representative of DNA-modifying enzymes group in DNA sensor design (review)

Rapid detection of nucleic acids (DNA or RNA) by inexpensive, selective, accurate, and highly sensitive methods is very important for biosensors. DNA-sensors based on DNA-modifying enzymes for fast determination and monitoring of pathogenic (Zika, Dengue, SARS-Cov-2 (inducer of COVID-19), human papillomavirus, HIV, etc.) viruses and diagnosis of virus-induced diseases is a key factor of this overview. Recently, DNA-modifying enzymes (Taq DNA polymerase, Phi29 DNA polymerase) have been widely used for the diagnosis of virus or pathogenic disease by gold standard (PCR, qPCR, RT-qPCR) methods, therefore, alternative methods have been reviewed. The main mechanisms of DNA metabolism (replication cycle, amplification) and the genomeediting tool CRISPR-Cas9 are purposefully discussed in order to address strategic possibility to design DNA-sensors based on immobilized DNA-enzymes. However, the immobilization of biologically active proteins on a gold carrier technique with the ability to detect viral or bacterial nucleic acids is individual for each DNA-modifying enzyme group, due to a different number of active sites, C and N terminal locations and arrangement, therefore, individual protocols based on the 'masking' of active sites should be elaborated for each enzyme.

Electroformation of peptide self-assembled monolayers on gold

The application of a potential to deposit a monolayer of 3-mercaptopropionic acid-histidinyl-histidinyl-histidinyl-aspartyl-aspartyl (3-MPA-HHHDD-OH) controls the density and molecular structure of the peptide monolayer, which results in different wettabilities of the surface, surface density, orientation of the molecule (extended or bent), and nonspecific adsorption of serum proteins. 3-MPA-HHHDD-OH must be deposited at 200 mV to maintain an extended configuration, which promoted low biofouling properties.

Biosensing for the environment and defence: aqueous uranyl detection using bacterial surface layer proteins

The fabrication of novel uranyl (UO(2)(2+)) binding protein based sensors is reported. The new biosensor responds to picomolar levels of aqueous uranyl ions within minutes using Lysinibacillus sphaericus JG-A12 S-layer protein tethered to gold electrodes. In comparison to traditional self assembled monolayer based biosensors the porous bioconjugated layer gave greater stability, longer electrode life span and a denser protein layer. Biosensors responded specifically to UO(2)(2+) ions and showed minor interference from Ni(2+), Cs(+), Cd(2+) and Co(2+). Chemical modification of JG-A12 protein phosphate and carboxyl groups prevented UO(2)(2+) binding, showing that both moieties are involved in the recognition to UO(2)(2+).