Analysis of crystallization and deposition process using electrochemical-quartz crystal microbalance: A review

Electrodeposition of paracetamol oxide for intelligent portable ratiometric detection of nicotine and ethyl vanillin β-D-glucoside

Herein, the electrodeposition of paracetamol oxide (PA ox) for the intelligent portable ratiometric detection of nicotine (NIC) and ethyl vanillin β-D-glucoside (EVG) is reported. PA ox electrodeposited on a screen-printed carbon electrode (SPCE) was used as a new fixed state ratiometric reference probe. A portable electrochemical workstation combined with a smart phone was applied as an intelligent portable electrochemical sensing platform. The sensor was studied by scanning electron microscopy (SEM), Fourier transform infrared spectrophotometry (FT-IR), ultraviolet-visible spectrophotometry (UV-vis), theoretical calculation, chronoamperometry, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and square wave voltammetry (SWV). Under optimized conditions, the detection range of NIC is 10-200 μmol L-1, and the detection limit is 0.256 μmol L-1. The detection range of EVG was 10-180 μmol L-1, and the detection limit was 0.058 μmol L-1. The sensor can realize the real-time detection of NIC and EVG concentration in cigarette samples quickly and accurately, and has good anti-interference, repeatability and stability.

Nanoarchitected graphene/copper oxide nanoparticles/MoS2 ternary thin films as highly efficient electrodes for aqueous sodium-ion batteries

Sodium-ion batteries (SIBs) operating in aqueous electrolyte are an emerging technology that promises to be safer, cheaper, more sustainable and more efficient than their lithium-based counterparts. One of the great challenges associated with this technology is the development of advanced materials with high specific capacity to be used as electrodes. Herein, we describe an ingenious strategy to prepare unprecedented tri-component nanoarchitected thin films with superior performance when applied as anodes in aqueous SIBs. Taking advantage of the broadness and versatility of the liquid-liquid interfacial route, three transparent nanocomposite films comprising graphene, molybdenum sulphide and copper oxide nanoparticles have been prepared. The samples were characterized using several techniques, and the results demonstrated that depending on the specific experimental strategy, different nanoarchitectures are achieved, resulting in different and improved properties. An astonishing capacity of 1377 mA h g-1 at 0.1 A g-1 and a degree of recovery of 100% were observed for the film in which the interactions among the components were optimized. This is among the highest capacity values reported in the literature and demonstrates the potential of these tri-component materials to be used as anodes in aqueous sodium-ion batteries.

Processing tactics for low-cost production of pure nuciferine from lotus leaf

Nuciferine is an important drug candidate for the treatment of many diseases. However, there is no general method for its low - cost production. In this work, a feasible method for the production of nuciferine from lotus leaf, using ultrasonic-assisted extraction-solid phase extraction (UAE-SPE) as extraction and cleanup procedure, was developed. Petroleum ether and silica gel have been successfully used as extraction solvent and adsorbent to integrate UAE with SPE, respectively. Except for filtration, no treatment (e.g. concentration and redissolution, etc) was needed on UAE extract before SPE and the effluents obtained in the loading process of SPE could be used as UAE extraction solvent without purification. No obvious decline in the extraction efficiency of UAE and adsorption capacity of SPE was observed at least for 5 runs, which provides a feasible way for the continuous production of nuciferine in industry, i.e. Cyclic UAE-SPE. Moreover, SPE column could be conveniently regenerated and reused without significant decline in its adsorption capacity at least for 5 cycles, which can be used to reduce the cost of the whole system further. In comparison with other cleanup procedures, Cyclic UAE-SPE showed apparent advantages in energy conservation and emission reduction. LLE and crystallization were applied to separate nuciferine from other impurities further. Under optimum conditions, the total recovery rate of nuciferine with a purity over 90.0% from lotus leaf reached 50.1%. All in all, the developed method has advantages in convenient operation, low cost, and high efficiency, thus, is fitting for the production of high purity nuciferine.

Design of surface nanostructures for chirality sensing based on quartz crystal microbalance

Quartz crystal microbalance (QCM) has been widely used for various sensing applications, including chirality detection due to the high sensitivity to nanogram or picogram mass changes, fast response, real-time detection, easy operation, suitability in different media, and low experimental cost. The sensing performance of QCM is dependent on the surface design of the recognition layers. Various strategies have been employed for studying the relationship between the structural features and the specific detection of chiral isomers. This review provides an overview of the construction of chiral sensing layers by various nanostructures and materials in the QCM system, which include organic molecules, supermolecular assemblies, inorganic nanostructures, and metal surfaces. The sensing mechanisms based on these surface nanostructures and the related potentials for chiral detection by the QCM system are also summarized.