Novel Calcium Carbonate-titania nanocomposites for enhanced sun light photo catalytic desulfurization process

Sonochemical synthesis of heterostructured ZnO/Bi2O3 for photocatalytic desulfurization

In this study, metal oxides nanoparticles heterogeneous photocatalysts prepared by coprecipitation and ultrasonic techniques were used for diesel desulfurization. They were characterized by scanning electron microscope, powder X-ray diffraction, energy dispersive analysis, diffused reflectance spectra, photoluminescence analysis and BET surface area. The surface area of catalyst B is larger than catalyst A confirming its higher reactivity. X-ray reflectance spectroscopy was used to analyze the sulfur contents in feed. Thiophene was used as a model fuel to evaluate the photocatalytic activity of catalysts A and B. Using the Scherrer equation, sharp and intense signals suggesting their higher degrees of crystallinity, with average crystal sizes for ZnO, Bi2O3, catalysts A and B, respectively; of 18, 14.3, 29.7, and 23.8 nm. The operational parameters of the desulfurization process were optimized and have been studied and the maximum sulfur removal was achieved via a further solvent extraction step. A diesel fuel with a 24 and 19 ppm sulfur content and hence a total sulfur removal of 94.6% and 95.7% was acquired for catalysts A and B, respectively (sulfur compounds concentration in diesel fuel feedstock was 450 ppm). These findings demonstrated that photocatalysts A and B are good and effective catalysts for desulfurization of diesel fuel.

A novel hydrogel beads based copper-doped Cerastoderma edule shells@Alginate biocomposite for highly fungicide sorption from aqueous medium

The engineering of a novel biocomposite based on Cerastoderma edule shells doped with copper and alginate (Ce-Cu@Alg) forming hydrogel beads was used for batch and dynamic adsorption thiabendazole (TBZ) pesticide from water. The prepared biosorbent was analyzed by various characterization techniques such as scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), Brunauer-Emmett-Teller analysis (BET), and energy dispersive spectroscopy (EDS), thermogravimetric and differential analysis (TGA-DTA). The results of the TBZ batch biosorption by Ce-Cu@Alg composite showed that the Langmuir model was the most adequate to describe the adsorption process, with a maximum adsorption capacity value of 21.98 mg/g. Moreover, the adsorption kinetics were adjusted by the pseudo-second-order model. The optimal conditions determined by the RSM approach coupled with the CCD design were 100 ppm of initial TBZ concentration, a Ce-Cu@Alg beads dose of 6 g/L and a contact time of 180 min for maximum removal of 83.42%. On the other hand, the TBZ sorption on a fixed bed of Ce-Cu@Alg beads was effective at high column height, low effluent flow and low solution concentration. The Thomas model was best fitted to the kinetic data. This study shows the possibility of using this new hybrid biocomposite in the industrial sector to treat large effluent volumes.

Novel photocatalyst system to deep desulfurization of petroleum model and gas condensate by Box–Behnken design

In this research, cobalt (Co)/molybdenum (Mo) and nickel (Ni) doped with titanium dioxide (TiO2) were loaded onto multi-walled carbon nanotubes (MWCNTs). Then, the magnetization catalyst, iron oxide (Fe3O4), was loaded on them, which was used for the deep desulfurization of dibenzothiophene (DBT). These catalysts were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, differential reflectance spectroscopy, and Brunauer–Emmett–Teller, Barrett–Joyner–Halenda, and vibrating sample magnetometer techniques. The photocatalytic activity of these catalysts was experienced under visible light using DBT. The response surface methodology based on the Box–Behnken design was used to evaluate parameters, including catalyst dosage (g), time (min), and concentration of DBT (mg L−1). The highest degradation efficiency under optimal conditions for CoMoNi/TiO2/MWCNTs/Fe3O4 catalysts with a catalyst dosage of 0.3 g, a time of 180 min, and a concentration of 50 mg L−1 was 99.99%. Optimum conditions were studied for desulfurization of the gas condensate. The highest desulfurization efficiency (90.33%) was obtained by the CoMoNi/TiO2/MWCNTs/Fe3O4 catalyst.

Mineral-Supported Photocatalysts: A Review of Materials, Mechanisms and Environmental Applications

Although they are of significant importance for environmental applications, the industrialization of photocatalytic techniques still faces many difficulties, and the most urgent concern is cost control. Natural minerals possess abundant chemical inertia and cost-efficiency, which is suitable for hybridizing with various effective photocatalysts. The use of natural minerals in photocatalytic systems can not only significantly decrease the pure photocatalyst dosage but can also produce a favorable synergistic effect between photocatalyst and mineral substrate. This review article discusses the current progress regarding the use of various mineral classes in photocatalytic applications. Owing to their unique structures, large surface area, and negatively charged surface, silicate minerals could enhance the adsorption capacity, reduce particle aggregation, and promote photogenerated electron-hole pair separation for hybrid photocatalysts. Moreover, controlling the morphology and structure properties of these materials could have a great influence on their light-harvesting ability and photocatalytic activity. Composed of silica and alumina or magnesia, some silicate minerals possess unique orderly organized porous or layered structures, which are proper templates to modify the photocatalyst framework. The non-silicate minerals (referred to carbonate and carbon-based minerals, sulfate, and sulfide minerals and other special minerals) can function not only as catalyst supports but also as photocatalysts after special modification due to their unique chemical formula and impurities. The dye-sensitized minerals, as another natural mineral application in photocatalysis, are proved to be superior photocatalysts for hydrogen evolution and wastewater treatment. This work aims to provide a complete research overview of the mineral-supported photocatalysts and summarizes the common synergistic effects between different mineral substrates and photocatalysts as well as to inspire more possibilities for natural mineral application in photocatalysis.

Recent Breakthrough in Layered Double Hydroxides and Their Applications in Petroleum, Green Energy, and Environmental Remediation

The fast development of the world civilization is continuously based on huge energy consumption. The extra-consumption of fossil fuel (petroleum, coal, and gas) in past decades has caused several political and environmental crises. Accordingly, the world, and especially the scientific community, should discover alternative energy sources to safe-guard our future from severe climate changes. Hydrogen is the ideal energy carrier, where nanomaterials, like layered double hydroxides (LDHs), play a great role in hydrogen production from clean/renewable sources. Here, we review the applications of LDHs in petroleum for the first time, as well as the recent breakthrough in the synthesis of 1D-LDHs and their applications in water splitting to H2. By 1D-LDHs, it is possible to overcome the drawbacks of commercial TiO2, such as its wide bandgap energy (3.2 eV) and working only in the UV-region. Now, we can use TiO2-modified structures for infrared (IR)-induced water splitting to hydrogen. Extending the performance of TiO2 into the IR-region, which includes 53% of sunlight by 1D-LDHs, guarantees high hydrogen evolution rates during the day and night and in cloudy conditions. This is a breakthrough for global hydrogen production and environmental remediation.