Micro-bubbles enhanced removal of diesel oil from the contaminated soil in washing/flushing with surfactant and additives

Bioremediation of Diesel-Contaminated Soil by Fungal Solid-State Fermentation

To address the poor removal of diesel in soil by indigenous microorganisms, we proposed a fungal solid-state fermentation (SSF) method for bioremediation. We screened Pycnoporus sanguineus 5.815, Trametes versicolor 5.996, and Trametes gibbosa 5.952 for their diesel-degrading abilities, with Trametes versicolor 5.996 showing the most promise. The fungal inoculum was obtained through SSF using wood chips and bran. Trametes versicolor 5.996 was applied to two treatments: natural attenuation (NA, diesel-contaminated soil) and bioremediation (BR, 10% SSF added to diesel-contaminated soil). Over 20 days, NA removed 12.9% of the diesel, while BR achieved a significantly higher 38.3% degradation rate. BR also increased CO2 and CH4 emissions but reduced N2O emissions. High-throughput sequencing indicated SSF significantly enriched known diesel-degrading microorganisms like Ascomycota (83.82%), Proteobacteria (46.10%), Actinobacteria (27.88%), Firmicutes (10.35%), and Bacteroidota (4.66%). This study provides theoretical support for the application of fungal remediation technology for diesel and improves understanding of microbiologically mediated diesel degradation and soil greenhouse gas emissions.

Varnish Formation and Removal in Lubrication Systems: A Review

This study presents the current literature regarding the investigation of varnish contamination among the various types of lubricant contaminations. As the duration of use of lubricants increases, the lubricant deteriorates and may become contaminated. Varnish has been known to cause filter plugging, sticking of the hydraulic valves and fuel injection pumps, flow obstruction, clearance reduction, poor heating and cooling performance, and increased friction and wear in various lubrication systems. These problems may also result in mechanical system failures, performance degradation, and increased maintenance and repair costs. To improve the problems caused by varnish contamination, an adequate understanding of varnish is required. Therefore, in this review, the definitions and characteristics, generating machinery, generating mechanisms, causes, measurement methods, and prevention or removal methods of varnish are summarized. Most of the data presented herein are reports from manufacturers related to lubricants and machine maintenance that are included in published works. We expect that this summary will be helpful to those who are engaged in reducing or preventing varnish-related problems.

Removal of mixed contaminants from landfill leachate-contaminated soil by flushing with bio-surfactant: laboratory column tests

Landfill leachate-contaminated soil is widespread all over the world. In order to study the removal of mixed contaminants from landfill leachate-contaminated soil by flushing with bio-surfactant, soil column test was conducted to select an optimum concentration of bio-surfactant saponin (SAP) at first. Then, the removal efficiencies of organic contaminants, ammonia nitrogen, and heavy metals from landfill leachate-contaminated soil by flushing with SAP were studied. At last, the toxicity of contaminated soil before and after flushing was estimated by sequential extraction of heavy metals and plant growth test. The test results showed that the SAP solution with the concentration of 2.5 CMC could effectively remove the mixed contaminants from soil and would not introduce excessive pollutants of SAP in soil. Specifically, the removal efficiencies of organic contaminant and ammonia nitrogen were 47.01% and 90.42%, respectively. And the removal efficiencies of Cu, Zn, and Cd were 29.42%, 22.55%, and 17.68%, respectively. During flushing, hydrophobic organic compounds as well as physisorption and ion-exchange ammonia nitrogen in soil were removed by the solubilization effect of SAP, and heavy metals were removed by the chelation of SAP. After flushing with SAP, the reduced partition index (I_R) value of Cu and Cd increased, and the mobility index (M_F) value of Cu decreased. In addition, flushing with SAP reduced the plant toxicity of contaminated soil, and the residual SAP in soil promoted the plant growth. Therefore, flushing with SAP offered great potentials in remediating the landfill leachate-contaminated soil.

The era of low-permeability sites remediation and corresponding technologies: A review

Rational utilization of soil resources and remediation of contaminated soils are imperative due to the rapidly growing demand for clean soils. Currently, many in-situ remediation technologies are less suitable at low-permeability sites due to the limitations of soil permeability. This work defines a low-permeability site as a site with hydraulic conductivity less than 10^-4 cm/s, and summarizes the migration characteristics of representative contaminants at low-permeability sites, and discusses the principles and practical applications of different technologies suitable for the remediation of low-permeability sites, including electrokinetic remediation technology, polymer flushing technology, fracturing technology, and in-situ thermal remediation technology. Enhanced and combined remediation technologies are further described because one remediation technology cannot remediate all contaminants. The prospects for the application of remediation technologies to low-permeability sites are also proposed. This work highlights the necessity of low-permeability sites remediation and the urgent need for new remediation technologies, with the hope to inspire future research on low-permeability sites.

Diesel removal and recovery from heavily diesel-contaminated soil based on three-liquid-phase equilibria of diesel + 2-butyloxyethanol + water

Diesel contamination poses a serious threat to ecosystem and human health. This study proposes a novel method for simultaneous diesel removal and recovery from heavily diesel-contaminated soil by washing based on three-liquid-phase equilibria of diesel+2-butoxyethanol+water. This work covers both theoretical-cum-experimental explorations. For this brand-new ternary three-liquid-phase system (TPS), Ternary-Gibbs and Fish-Shaped phase diagrams were constructed through the phase behavior investigation to provide theoretical support for diesel removal/recovery. As the experiment demonstrated, the removal efficiency was up to 87.5 % for the contaminated soil with diesel content of 226,723 mg/kg, and the recovery rate reached 73.8 %. In addition, the TPS could also be used continuously during the washing process while avoiding solution purification, and the detached diesel would automatically float into the top phase without complicated separation. The mechanism of diesel removal was determined as the surface "stripping" effect based on ultralow interfacial tension, and the enhanced process involved "stripping+dissolution". The treated soil contained almost negligible organic solvent residue and was therefore appropriate for plant cultivation. The recovered diesel exhibited less variation from commercial diesel in composition and properties, possessing a higher potential for reuse. Moreover, this study also provided key insights into the residual mechanisms of recalcitrant hydrocarbons in the soil.

Potential for selective oxidation of aniline in soil washing effluent by active chlorine and testing its practicality

Recovery of surfactants in the soil washing effluent (SWE) can significantly reduce the cost of the soil washing (SW) technology. This paper consists of two parts experiments. The first part constructed a selective oxidation system of active chlorine by electrochemical technology to treat SWE. Three factors, current density, NaCl concentration and TW 80 to aniline concentration ratio (T/A), were set up for a total of nine sets of experiments after orthogonal design. The results of ANOVA analysis and visual analysis showed that the NaCl concentration greatly affected the aniline removal efficiency (ARE) and the TW 80 retention efficiency (TW 80 RE), and the effects were in opposite directions. The biotoxicity of the SWE decreased as the experiment progressed, and at the end of the experiment, 30%-45% of TW 80 was still present in each set. And the oxidation group quenching experiments determined that the degradation of aniline was mainly contributed by active chlorine. Because active chlorine slowed the loss rate of TW 80, the electrochemical treatment of SWE + soil in-situ sequential batch recirculation washing method was designed, and 50% of aniline in the soil was washed out after 125h. At the end of the experiment, the less biotoxic SWE was collected where no aniline and TW 80 were present, and only small organic acids were present after the GC-MS test. The method has a great potential to be applied as it shows good results in the treatment of soil pollution incidents.

Utilization of a biosurfactant foam/nanoparticle mixture for treatment of oil pollutants in soil

Oil contamination has become a primary environmental concern due to increased exploration, production, and use. When oil enters the soil, it may attach or adsorb to soil particles and stay in the soil for an extended period, contaminating the soil and surrounding areas. Nanoparticles have been widely used for the treatment of organic pollutants in the soil. Surfactant foam has effectively been employed to remediate various soil contaminants or recover oil compounds. In this research, a mixture of biosurfactant foam/nanoparticle was utilized for remediation of oil-contaminated soil. The results demonstrated that the biosurfactant/nanoparticle mixture and nitrogen gas formed high-quality and stable foams. The foam stability depended on the foam quality, biosurfactant concentration, and nanoparticle dosage. The pressure gradient change in the soil column relied on the flowrate (N₂ gas + surfactant/nanoparticle mixture), foam quality, and biosurfactant concentration. The optimal conditions to obtain good quality and stable foams and high oil removal efficiency involved 1 vol% rhamnolipid, 1 wt% nanoparticle, and 1 mL/min flowrate. Biosurfactant foam/nanoparticle mixture was effectively used to remediate oil-contaminated soil, whereas the highest treatment efficiency was 67%, 59%, and 52% for rhamnolipid biosurfactant foam/nanoparticle, rhamnolipid biosurfactant/nanoparticle, and only rhamnolipid biosurfactant, respectively. The oil removal productivity decreased with the increase of flowrate due to the shorter contact time between the foam mixture and oil droplets. The breakthrough curves of oil pollutants in the soil column also suggested that the foam mixture's maximum oil treatment efficiency was higher than biosurfactant/nanoparticle suspension and only biosurfactant.

Synthetic and Natural Surfactants for Potential Application in Mobilization of Organic Contaminants: Characterization and Batch Study

In this paper, we investigated the abilities of five sugar-based synthetic surfactants and biosurfactants from three different families (i.e., alkyl polyglycoside (APG), sophorolipid (SL), and rhamnolipid (RL)) to dissolve and mobilize non-aqueous phase liquid (NAPL) components, i.e., toluene and perchloroethylene (PCE), adsorbed on porous matrices. The objective of this study was to establish a benchmark for the selection of suitable surfactants for the flushing aquifer remediation technique. The study involved a physicochemical characterization of the surfactants to determine the critical micelle concentration (CMCs) and interfacial properties. Subsequently, a batch study, through the construction of adsorption isotherms, made it possible to evaluate the surfactants’ capacities in contaminant mobilization via the reduction of their adsorptions onto a reference adsorbent material, a pine wood biochar (PWB). The results indicate that a synthetic surfactant from the APG family with a long fatty acid chain and a di-rhamnolipid biosurfactant with a shorter hydrophobic group offered the highest efficiency values; they reduced water surface tension by up to 54.7% and 52%, respectively. These two surfactants had very low critical micelle concentrations (CMCs), 0.0071 wt% and 0.0173 wt%, respectively; this is critical from an economical point of view. The batch experiments showed that these two surfactants, at concentrations just five times their CMCs, were able to reduce the adsorption of toluene on PWB by up to 74% and 65%, and of PCE with APG and RL by up to 65% and 86%, respectively. In general, these results clearly suggest the possibility of using these two surfactants in surfactant-enhanced aquifer remediation technology.

Augmentation of an Engineered Bacterial Strain Potentially Improves the Cleanup of PCB Water Pollution

Polychlorinated biphenyls (PCBs) are recalcitrant organohalide pollutants, consisting of 209 congeners. PCB cleanup in natural landscapes is expected to be achieved by the metabolic activity of microorganisms, but aerobic PCB-degrading bacteria that inhabit sites polluted by PCBs cannot degrade all PCB congeners due to the specificity of their enzymes. In this study, we investigated the degradability of PCBs when a genetically modified PCB-degrading bacterium was compounded with wild-type PCB-degrading bacteria. We used two bacterial strains, Comamonas testosteroni YAZ2 isolated from a PCB-uncontaminated natural landscape and Escherichia coli BL21(DE3) transformed with a biphenyl dioxygenase (BphA) gene from a well-known PCB degrader, Burkholderia xenovorans LB400. The enzymatic specificities of BphA were 2,3-dioxygenation in the YAZ2 and 2,3- and 3,4-dioxygenations in the recombinant E. coli. For the PCB-degrading experiment, a dedicated bioreactor capable of generating oxygen microbubbles was prototyped and used. The combined cells of the recombinant and the wild-type strains with an appropriate composite ratio degraded 40 mg/L of Kaneclor KC-300 to 0.3 ± 0.1 mg/L within 24 h. All of the health-toxic coplanar PCB congeners in KC-300 were degraded. This study suggested that the augmentation of an engineered bacterial strain could improve the cleanup of PCB water pollution. It also revealed the importance of the ratio of the strains with different PCB-degrading profiles to efficient degradation and that the application of oxygen microbubbles could rapidly accelerate the cleanup. IMPORTANCE PCB cleanup technique in a natural environment relies on the use of enzymes from microorganisms, primarily biphenyl dioxygenase and dehalogenase. Herein, we focused on biphenyl dioxygenase and created a recombinant PCB-degrading E. coli strain. Despite the development of environments for the field use of transgenic microbial strains around the world, verification of the applicability of transgenic microbial strains for PCB cleanup in the field has not yet been reported. We tentatively verified the extent to which degradability could be obtained by an augmentation model of a transgenic strain, the enzyme expression of which is easily regulated in rivers and lakes with PCB pollution. Our experiments used a dedicated bioreactor to model the natural landscape and produced results superior to those of bioremediation or biostimulation methods. The application of micro-nano bubbles, which has recently been discussed, to the cleanup of environmental pollution was also found to be useful in this study.