Evaluation of ammonium removal using a chitosan-g-poly (acrylic acid)/rectorite hydrogel composite

Biopolymer Meets Nanoclay: Rational Fabrication of Superb Adsorption Beads from Green Precursors for Efficient Capture of Pb(II) and Dyes

Renewable, green, and safe natural biopolymer-derived materials are highly desired for the purification of pollutants, but significantly improving their performance without the introduction of additional harmful chemicals remains a huge challenge. Based on the concept of "structure optimization design", environment-friendly composite beads (named SA/PASP/RE) with excellent adsorption performance and recyclability were rationally constructed through a green ionic crosslinking route, using the completely green biopolymer sodium alginate (SA), sodium salt of polyaspartic acid (PASP), and the natural nanoclay rectorite (RE) as starting materials. The nano-layered RE was embedded in the polymer matrix to prevent the polymer chain from becoming over-entangled so that more adsorption sites inside the polymer network were exposed, which effectively improved the mass transfer efficiency of the adsorbent and the removal rate of contaminants. The composite beads embedded with 0.6% RE showed high adsorption capacities of 211.78, 197.13, and 195.69 mg/g for Pb(II) and 643.00, 577.80, and 567.10 mg/g for methylene blue (MB) in Yellow River water, Yangtze River water, and tap water, respectively. And the beads embedded with 43% RE could efficiently adsorb Pb(II) and MB with high capacities of 187.78 mg/g and 586.46 mg/g, respectively. This study provides a new route to design and develop a green, cost-effective, and efficient adsorbent for the decontamination of wastewater.

Novel Grafted Hydrogel for Iron and Ammonia Removal from Groundwater: A Synthesis and Computational Chemistry Study

Current research is moving towards iron and ammonia elimination from groundwater. Here, we are using a poly acrylic-poly acrylamide hydrogel that is grafted with 3-chloroaniline. This copolymer was synthesized by addition polymerization technique. The effects of agitation time, dosage and adsorbent temperature on the removal process sensitivity were investigated. The copolymer was described experientially and theoretically. Isothermal kinetic adsorption models are discussed. This hydrogel could be regenerated efficiently (98.3% removal of iron and 100% removal of ammonia). The density functional theory (DFT) method, using B3LYP/6-311G(d,p), and the LANL2DZ level of the theory were managed to investigate the stationary states of the grafted copolymer and the complexation energy of the hydrogel with the studied cations. DFT has been used to investigate the Natural Bond Orbital (NBO) properties to locate the most negative centers on the hydrogel. The calculated complexation energy showed hydrogel selectivity with regard to the studied cations.

Probing and Manipulating Noncovalent Interactions in Functional Polymeric Systems

Noncovalent interactions, which usually feature tunable strength, reversibility, and environmental adaptability, have been recognized as driving forces in a variety of biological and chemical processes, contributing to the recognition between molecules, the formation of molecule clusters, and the establishment of complex structures of macromolecules. The marriage of noncovalent interactions and conventional covalent polymers offers the systems novel mechanical, physicochemical, and biological properties, which are highly dependent on the binding mechanisms of the noncovalent interactions that can be illuminated via quantification. This review systematically discusses the nanomechanical characterization of typical noncovalent interactions in polymeric systems, mainly through direct force measurements at microscopic, nanoscopic, and molecular levels, which provide quantitative information (e.g., ranges, strengths, and dynamics) on the binding behaviors. The fundamental understandings of intermolecular and interfacial interactions are then correlated to the macroscopic performances of a series of noncovalently bonded polymers, whose functions (e.g., stimuli-responsiveness, self-healing capacity, universal adhesiveness) can be customized through the manipulation of the noncovalent interactions, providing insights into the rational design of advanced materials with applications in biomedical, energy, environmental, and other engineering fields.

Formation of iodinated aromatic DBPs at different molar ratios of chlorine and nitrogen in iodide-containing water

Variations in iodinated aromatic disinfection byproducts (DBPs) in the presence of I^- and organic compounds as a function of reaction time in different molar ratios (MRs) of HOCl:NH₃-N were investigated. Up to 17 kinds of iodinated aromatic DBPs were identified in the breakpoint chlorination of iodide (I^-)/organic (phenol, bisphenol S (BPS) and p-nitrophenol (p-NP)) systems, and the possible pathways for the formation of iodinated aromatic DBPs were proposed. The reaction pathways include HOCl/HOI electrophilic substitution and oxidation, while the dominant iodinated DBPs were quantified. In the I^-/phenol system (pH = 7.0), the sum of the concentrations of four iodinated aliphatic DBPs ranged from 0.32 to 1.04 μM (triiodomethane (TIM), dichloroiodomethane (DCIM), diiodochloromethane (DICM) and monoiodoacetic acid (MIAA)), while the concentration of 4-iodophenol ranged from 2.99 to 12.87 μM. The concentration of iodinated aromatic DBPs remained stable with an MR = 1:1. When the MR was 6:1, iodinated aromatic DBPs decreased with increasing reaction time, in which the main disinfectant in the system was active chlorine. This study proposed the formation mechanism of iodinated aromatic DBPs during the breakpoint chlorination of iodide-containing water. These results can be used to control the formation of hazardous iodinated aromatic DBPs in the disinfection of iodine containing water.

Optimization of anti-corrosion performance of novel magnetic polyaniline-Chitosan nanocomposite decorated with silver nanoparticles on Al in simulated acidizing environment using RSM

The suitability of newly synthesized magnetic polyaniline-Chitosan nanocomposite decorated with silver nanoparticles (Ag@PANI-CS-Fe₃O₄) as a robust corrosion inhibitor for Aluminum (Al) in a 5 M HCl environment has been investigated via Weight Loss (WL), Alternating Current (AC)-Impedance Spectroscopy (IS), Potentiontiodynamic polarization (Tafel plots), and Scanning Electron Microscopy (SEM) techniques. The protection efficiency (PE) was mathematically modeled using the Response Surface Methodology (RSM) to fit an empirical relation in terms of temperature, nanocomposite concentration, and time using the face-centered central composite design. The model was accurate with a coefficient of determination (R² = 99.27%). The negative Gibb's free energy of adsorption (ΔG_ads) values confirmed the spontaneity of Freundlich adsorption isotherm process on Al in 5 M HCl solution. The optimization simulation yielded maximum protection efficiency (of 97.88%) at 5 mg/L nanocomposite concentration, 1 h time, and an intermediate temperature of 304.8 K. Furthermore, the sensitivity of PE was evaluated to find that the low temperature 303 K is favorable for PE, whereas higher temperature will act adversely on PE. The results obtained by the RSM model are in agreement with the experimental observations.

A Systematic Study of Ammonia Recovery from Anaerobic Digestate Using Membrane-Based Separation

Ammonia recovery from synthetic and real anaerobic digestates was accomplished using hydrophobic flat sheet membranes operated with H₂SO₄ solutions to convert ammonia into ammonium sulphate. The influence of the membrane material, flow rate (0.007, 0.015, 0.030 and 0.045 m³ h⁻¹) and pH (7.6, 8.9, 10 and 11) of the digestate on ammonia recovery was investigated. The process was carried out with a flat sheet configuration at a temperature of 35 °C and with a 1 M, or 0.005 M, H₂SO₄ solution on the other side of the membrane. Polytetrafluoroethylene membranes with a nominal pore radius of 0.22 µm provided ammonia recoveries from synthetic and real digestates of 84.6% ± 1.0% and 71.6% ± 0.3%, respectively, for a membrane area of 8.6 × 10⁻⁴ m² and a reservoir volume of 0.5 L, in 3.5 h with a 1 M H₂SO₄ solution and a recirculation flow on the feed side of the membrane of 0.030 m³ h⁻¹. NH₃ recovery followed first order kinetics and was faster at higher pHs of the H₂SO₄ solution and recirculation flow rate on the membrane feed side. Fouling resulted in changes in membrane surface morphology and pore size, which were confirmed by Atomic Force Microscopy and Air Displacement Porometry.

A review on the use of chitosan and chitosan derivatives as the bio-adsorbents for the water treatment: Removal of nitrogen-containing pollutants

Chitosan and its derivatives have been widely used as the adsorbents for different types of water pollutants. This review paper lists various physically and chemically modified chitosan-based adsorbents such as chitosan beads, cross-linked chitosan, chitosan-polymer composites, chitosan-inorganic material composites, and chitosan-metal complexes for the removal of nitrogen-containing pollutants (nitrate, nitrite, ammonia, and ammonium ions) from aqueous solutions. It covers preparation strategies, the effect of modification on adsorbent structure, and the impact of adsorption variables using batch and fixed-bed column studies. In addition to demonstrating the applications of chitosan and its derivatives in the removal of nitrogenous pollutants from water, it helps researchers understand the influence of modification of chitosan on its adsorption capacity as well as physical and chemical properties.

Separation of pollutants from aqueous solution using nanoclay and its nanocomposites: A review

Wastewater is always composed of different pollutants, most of which are toxic to the living being. It is very tough to separate all those diverse groups of contaminants using a single process or single material. Rather a sustainable and environment friendly processes should be adapted to restrict the secondary pollution generation. Nanoclay and its nanocomposites are one of the most used adsorbents that have been modified and used for the separation of almost all types of pollutants, including dyes, heavy metals, fluoride, nitrate, ammonia, emerging pollutants and bacteria. They are relatively inexpensive, easy to exploit and relatively maintenance-free. Thus, recent research bloomed for developing suitable adsorbents, including clay nanocomposites. The advantages and drawbacks of all the clay nanocomposites-based processes have been discussed critically in this article. Nano-clays or other nanoparticles incorporated synthetic and natural polymers-based clay nanocomposites were synthesized, and it was found that they can remove dyes in the range between 48 mg/g and 1994 mg/g. Similarly, they separate a diverse group of heavy metal ions, including As, Cu, Co, Pd, Zn, Cr, Ni, Cd, and Hg, in the range of 0.073-1667 mg/g. The clay nanocomposites also showed fluoride removal efficacy in the range of 0.134-23 mg/g. They are also useful for the separation of emerging pollutants like pesticides, pharmaceuticals, personal care products, trace elements, and particulate matters in the range of 0.1-651 mg/g the clay nanocomposites showed considerable nitrate, ammonia and bacteria removal efficacy too. Though it seems promising, more investigations with real wastewater and pilot-scale studies are recommended to explore large-scale wastewater treatment capabilities.

Incorporation of Layered Rectorite into Biocompatible Core-Sheath Nanofibrous Mats for Sustained Drug Delivery

Searching for drug carries with controlled release and good biocompatibility has always been one of the research hotspots and difficulties. Herein, core-sheath nanofibrous mats (NFs) consisting of biocompatible poly(ethylene oxide) (PEO, core) and poly(l-lactic acid) (PLLA, sheath) for drug delivery were fabricated via coaxial electrospinning strategy. The nontoxic layered silicate rectorite (REC) with 0.5-1 wt % amount was introduced in the sheath for sustained drug delivery. Layered REC could be intercalated with PLLA macromolecule chains, leading to the densified structure for loading and keeping doxorubicin hydrochloride (DOX) while reversibly capturing and releasing DOX to delay the drug migration due to its high cation activity. The addition of REC in NFs could delay the initial burst release of DOX and prolong the residence time from 12 to 96 h. Moreover, DOX-loaded core-sheath NFs had in vitro culture with strong antitumor activity, which was confirmed by cytotoxicity results and live and dead assay. HepG₂ tumor-bearing xenograft further demonstrated the tumor-suppression effect and the excellent safety of the DOX-loaded core-sheath NFs in vivo. The constructed NFs as drug carriers showed great potential in the local treatment of solid tumors.

Circular economy-driven ammonium recovery from municipal wastewater: State of the art, challenges and solutions forward

In current biological nitrogen removal (BNR) processes, most of ammonium in municipal wastewater is biologically transformed to nitrogen gas, making ammonium recovery impossible. Thus, this article aims to provide a holistic review with in-depth discussions on (i) current BNR processes for municipal wastewater treatment, (ii) environmental and economic costs behind ammonium in municipal wastewater, (iii) state of the art of ammonium recovery from municipal wastewater including anaerobic membrane bioreactor turning municipal wastewater to a liquid fertilizer, capturing ammonium in phototrophic biomass, waste activated sludge for land application, bioelectrochemical systems, biological conversion of ammonium to nitrous oxide as a fuel oxidizer, and adsorption, (iv) feasibility and challenge of adsorption for ammonium recovery from municipal wastewater and (v) innovative municipal wastewater reclamation processes coupled with ammonium recovery. Moving forward, municipal wastewater reclamation and resource recovery should be addressed under the framework of circular economy.

Superabsorbent polymers: A state-of-art review on their classification, synthesis, physicochemical properties, and applications

Superabsorbent polymers (SAP) and modified natural polymer hydrogels are widely and increasingly used in agriculture, health care textiles, effluent treatment, drug delivery, tissue engineering, civil concrete structure, etc. However, not many comprehensive reviews are available on this class of novel polymers. A review covering all the viable applications of SAP will be highly useful for researchers, industry persons, and medical, healthcare, and agricultural purposes. Hence, an attempt has been made to review SAPs with reference to their classifications, synthesis, modification by crosslinking, and physicochemical characterization such as morphology, swellability, thermal and mechanical properties, lifetime prediction, thermodynamics of swelling, absorption, release and transport kinetics, quantification of hydrophilic groups, etc. Besides, the possible methods of fine-tuning their structures for improving their absorption capacity, fast absorption kinetics, mechanical strength, controlled release features, etc. were also addressed to widen their uses. This review has also highlighted the biodegradability, commercial viability and market potential of SAPs, SAP composites, the feasibility of using biomass as raw materials for SAP production, etc. The challenges and future prospects of SAP, their safety, and environmental issues are also discussed.

Modified Poly(acrylic acid)-Based Hydrogels for Enhanced Mainstream Removal of Ammonium from Domestic Wastewater

Rapid and continuous ammonium adsorption from mainstream coupled with side-stream ammonium recovery and adsorbent regeneration could enable ammonium recovery from domestic wastewater. This study describes the use of tailored poly(acrylic acid)-based (NaPAA) hydrogels as effective sorbents for ammonium removal from domestic wastewater. Modified NaPAA hydrogels having 60% ionization and 4.8 mol % N',N'-methylenebisacrylamide as the cross-linker reduced the overall swelling by 92% from 407 to 31 g/g because of higher cross-linking density. At hydrogel loadings of 2.5-7.5 g/L, the NaPAA hydrogels achieved ammonium concentrations of 8.3 ± 0.6 to 10.1 ± 0.1 mg/L NH₄-N, which corresponds to removal efficiencies of 53-77% after 10 min of contact time in real domestic wastewater. At the same hydrogel loadings, the ammonium removal efficiency of NaPAA hydrogels in synthetic wastewater was found to be comparable to that in real sewage (71% vs 69%, respectively), suggesting that the sorption performance is only marginally affected by organic constituents found in domestic wastewater. In addition, the NaPAA hydrogels removed 25-51% ammonium in 10 min from synthetic streams having 200-400% higher ionic strengths than those commonly observed in sewage. Furthermore, simulation studies showed that a discharge concentration of ∼1.9 mg/L NH₄-N, well below the commonly applied discharge limits in most regions, can be achieved using mainstream ammonium removal by NaPAA hydrogels followed by biological assimilation from the growth of ordinary heterotrophic organisms.

Mainstream Ammonium Recovery to Advance Sustainable Urban Wastewater Management

Throughout the 20th century, the prevailing approach toward nitrogen management in municipal wastewater treatment was to remove ammonium by transforming it into dinitrogen (N₂) using biological processes such as conventional activated sludge. While this has been a very successful strategy for safeguarding human health and protecting aquatic ecosystems, the conversion of ammonium into its elemental form is incompatible with the developing circular economy of the 21st century. Equally important, the activated sludge process and other emerging ammonium removal pathways have several environmental and technological limitations. Here, we assess that the theoretical energy embedded in ammonium in domestic wastewater represents roughly 38-48% of the embedded chemical energy available in the whole of the discharged bodily waste. The current routes for ammonium removal not only neglect the energy embedded in ammonium, but they can also produce N₂O, a very strong greenhouse gas, with such emissions comprising the equivalent of 14-26% of the overall carbon footprint of wastewater treatment plants. N₂O emissions often exceed the carbon emissions related to the electricity consumption for the process requirements of WWTPs. Considering these limitations, there is a need to develop alternative ammonium management approaches that center around recovery of ammonium from domestic wastewater rather than deal with its "destruction" into elemental dinitrogen. Current ammonium recovery techniques are applicable only at orders of magnitude above domestic wastewater strength, and so new techniques based on physicochemical adsorption are of particular interest. A new pathway is proposed that allows for mainstream ammonium recovery from wastewater based on physicochemical adsorption through development of polymer-based adsorbents. Provided adequate adsorbents corresponding to characteristics outlined in this paper are designed and brought to industrial production, this adsorption-based approach opens perspectives for mainstream continuous adsorption coupled with side-stream recovery of ammonium with minimal chemical requirements. This proposed pathway can bring forward an effective resource-oriented approach to upgrade the fate of ammonium in urban water management without generating hidden externalized environmental costs.

Cellulose-based hydrogel materials: chemistry, properties and their prospective applications

Hydrogels based on cellulose comprising many organic biopolymers including cellulose, chitin, and chitosan are the hydrophilic material, which can absorb and retain a huge proportion of water in the interstitial sites of their structures. These polymers feature many amazing properties such as responsiveness to pH, time, temperature, chemical species and biological conditions besides a very high-water absorption capacity. Biopolymer hydrogels can be manipulated and crafted for numerous applications leading to a tremendous boom in research during recent times in scientific communities. With the growing environmental concerns and an emergent demand, researchers throughout the globe are concentrating particularly on naturally derived hydrogels due to their biocompatibility, biodegradability and abundance. Cellulose-based hydrogels are considered as useful biocompatible materials to be used in medical devices to treat, augment or replace any tissue, organ, or help function of the body. These hydrogels also hold a great promise for applications in agricultural activity, as smart materials and some other useful industrial purposes. This review offers an overview of the recent and contemporary research regarding physiochemical properties of cellulose-based hydrogels along with their applications in multidisciplinary areas including biomedical fields such as drug delivery, tissue engineering and wound healing, healthcare and hygienic products as well as in agriculture, textiles and industrial applications as smart materials.

A review on acrylic based hydrogels and their applications in wastewater treatment

The acrylic based hydrogels have attracted the attention of many researchers in the field of pollutants adsorption such as dyes and metal cations due to their high swelling and adsorption capacities. This review introduces acrylic based hydrogels and focuses on their adsorption properties. We first described the methods for synthesizing hydrogels. Usual methods of characterization of acrylic based hydrogels such as swelling, adsorption capacity and desorption efficiency of the pollutants have been investigated. In addition, the adsorption isotherm and kinetic models which determine the mechanism of pollutants' adsorption by hydrogels have been introduced and relations that determine the values of thermodynamic parameters which define accomplishment of adsorption process have been investigated. In the following sections, a perfect insight has been provided on natural and synthetic acrylic based hydrogels. The effective parameters of swelling and adsorption by acrylic based hydrogels have been reviewed and the mechanism of pollutant's adsorption by acrylic based hydrogels has been discussed.

Rapid removal of ammonium from domestic wastewater using polymer hydrogels

To date, technologies to recover ammonium from domestic wastewater from the mainstream have not found widespread application. This is largely due to the low ammonium concentrations in these wastewater streams. This paper reports on the use of polymer hydrogels for rapid sorption of ammonium from domestic wastewater coupled with efficient regeneration by mild acid washing. The sorption capacity of the hydrogel was 8.8–32.2 mg NH₄–N/g, which corresponds to removal efficiencies ranging from 68% to 80% NH₄–N, increasing proportionally with the initial ammonium concentration. It was, however, unaffected by changes in pH, as the sorption capacity remained constant from pH 5.0–8.0. Importantly, effective regeneration of the hydrogels under mildly acidic conditions (i.e. pH 4.0) was demonstrated with minimal loss in sorption performance following multiple sorption/desorption cycles. Overall, this study highlights the potential of low-cost polymer hydrogels for achieving mainstream ammonium recovery from domestic wastewater.

A microscopic view of graphene-oxide/poly(acrylic acid) physical hydrogels: effects of polymer charge and graphene oxide loading

In this work we have examined in detail by means of fully atomistic molecular dynamics simulations, physical hydrogels formed by a polymer electrolyte, poly(acrylic acid), and graphene oxide, at two different charging states of the polymer and two different graphene oxide concentrations. It was found that variations of these parameters incurred drastic changes in general morphological characteristics of the composite materials, the degree of physical adsorption of polyelectrolyte chains onto the graphene oxide surface, the polymer dynamic response at local and global length scales, in the charge distributions around the components, and in the mobility of the counterions. All these microscopic features are expected to significantly affect macroscopic physical properties of the hydrogels, such as their mechanical responses and their electrical behaviors.

Removing ammonium from water and wastewater using cost-effective adsorbents: A review

Ammonium is an important nutrient in primary production; however, high ammonium loads can cause eutrophication of natural waterways, contributing to undesirable changes in water quality and ecosystem structure. While ammonium pollution comes from diffuse agricultural sources, making control difficult, industrial or municipal point sources such as wastewater treatment plants also contribute significantly to overall ammonium pollution. These latter sources can be targeted more readily to control ammonium release into water systems. To assist policy makers and researchers in understanding the diversity of treatment options and the best option for their circumstance, this paper produces a comprehensive review of existing treatment options for ammonium removal with a particular focus on those technologies which offer the highest rates of removal and cost-effectiveness. Ion exchange and adsorption material methods are simple to apply, cost-effective, environmentally friendly technologies which are quite efficient at removing ammonium from treated water. The review presents a list of adsorbents from the literature, their adsorption capacities and other parameters needed for ammonium removal. Further, the preparation of adsorbents with high ammonium removal capacities and new adsorbents is discussed in the context of their relative cost, removal efficiencies, and limitations. Efficient, cost-effective, and environmental friendly adsorbents for the removal of ammonium on a large scale for commercial or water treatment plants are provided. In addition, future perspectives on removing ammonium using adsorbents are presented.

Hydrogels Synthesized by Electron Beam Irradiation for Heavy Metal Adsorption

Poly(acrylamide co-acrylic acid) hydrogels were prepared by free-radical copolymerization of acrylamide and acrylic acid in aqueous solutions using electron beam irradiation in the dose range of 2.5 kGy to 6 kGy in atmospheric conditions and at room temperature. The influence of the absorbed dose, the amount of cross-linker (trimethylolpropane trimethacrylate) and initiator (potassium persulfate) on the swelling properties and the diffusion coefficient and network parameters of hydrogels were investigated. The structure and morphology of hydrogels were characterized by Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). The use of the obtained hydrogels by the removal of Cu²⁺ and Cr⁶⁺ from aqueous solutions was investigated at room temperature. During the adsorption of metal ions on hydrogels, the residual metal ion concentration in the solution was measured by an atomic absorption spectrophotometer (AAS). It has been established that the use of a relatively small amount of trimethylolpropane trimethacrylate for hydrogel preparation has led to the increasing of swelling up to 8500%.

Adsorption of methylene blue by using novel chitosan-g-itaconic acid/bentonite nanocomposite - equilibrium and kinetic study

In this study, novel chitosan-g-itaconic acid/bentonite (CTS-g-IA/BT) and chitosan/bentonite (CTS/BT) nanocomposites were synthesized for adsorption of methylene blue (MB) from aqueous solution. The process was pH-sensitive and maximum sorption was obtained at pH 6 (CTS-g-IA/BT) and 7 (CTS/BT) in 76 h agitation time using 0.03 g of nanocomposites for 50 mL of MB solution. The results showed that in pH less than 6, the adsorption capacity of CTS-g-IA/BT nanocomposite due to the existence of IA monomer is less than that of CTS/BT nanocomposite. The Fourier transform infrared spectroscopy (FTIR) spectrum of CTS-g-IA/BT revealed that both itaconic acid and BT present in the nanocomposite structure, and also the -OH groups of BT, -NH₂ and -OH of CTS participated in nanocomposite formation. According to the FTIR results, a schematic diagram of the nanocomposite synthesis was presented. The kinetic results indicated that the adsorption of MB fitted well with the pseudo-second-order kinetic model. The equilibrium data followed Langmuir isotherm with the maximum adsorption capacity of 500 and 181.818 mg/g for CTS-g-IA/BT and CTS/BT nanocomposites, respectively. The negative values of Gibbs free energy change (ΔG⁰) and the positive values of ΔH⁰ confirmed that the adsorption process is spontaneous and endothermic. The positive values of ΔS⁰ suggested the randomness of adsorption at interface.

Investigation of ammonium adsorption on Algerian natural bentonite

Adsorption of several chemical contaminants onto clay minerals is the most recommended technique applied in the wastewater treatment field, owing to its low economic cost, efficiency, and low power consumption. In this context, natural bentonite particles with 80-μm diameter were investigated for the ammonium adsorption in aqueous solution using an incubator that kept the constant temperature and stirring speed at 200 RPM. The study of different experimental parameters effect on the adsorption process revealed that the raw bentonite have adsorbed approximately 53.36 % of the initial ammonium concentration at pH 7 and temperature of 30 °C. This percentage has been improved by increasing the adsorbent dosage in solution, which could reach up to 81.2 % at 40 g/L of bentonite with an initial ammonium concentration of 10 mg-NH₄⁺/L. Moreover, experimental data modeling allowed us to conclude that the adsorption isotherm obeys to both models of Langmuir and Freundlich.

Highly cost-effective and high-strength hydrogels as dye adsorbents from natural polymers: chitosan and cellulose

Cost-effective chitosan/REC/cellulose hydrogels with high-strength are used for highly efficient dye adsorption.

Study on the Effect of the Three-Dimensional Electrode in Degradation of Methylene Blue by Lithium Modified Rectorite

This study presents the electrochemical degradation of methylene blue (MB) wastewater in a synthetic solution using three-dimensional particle electrodes. The novel particle electrodes were fabricated in this work using the lithium modified rectorite (Li-REC). The adsorption property of the fabricated particle electrodes was studied in a series of experiments. The optimum electrochemical operating conditions of plate distance, cell voltage, and concentration of electrolyte were 2 cm, 9 V, and 0.06 mol L^-1, respectively. It was also found that microwave irradiation can effectively improve the adsorption property and electrical property of the fabricated electrodes. In addition, the scanning electron microscope (SEM) of the fabricated electrodes was investigated. The experimental results revealed the order of adsorption property and electrical property of the fabricated electrodes. So, fabricated electrodes are not only of low cost and mass produced, but also efficient to achieve decolorization of MB solution.

Biomimetic Hydrogel Composites for Soil Stabilization and Contaminant Mitigation

We have developed a novel method to synthesize a hyper-branched biomimetic hydrogel network across a soil matrix to improve the mechanical strength of the loose soil and simultaneously mitigate potential contamination due to excessive ammonium. This method successfully yielded a hierarchical structure that possesses the water retention, ion absorption, and soil aggregation capabilities of plant root systems in a chemically controllable manner. Inspired by the robust organic-inorganic composites found in many living organisms, we have combined this hydrogel network with a calcite biomineralization process to stabilize soil. Our experiments demonstrate that poly(acrylic acid) (PAA) can work synergistically with enzyme-induced carbonate precipitation (EICP) to render a versatile, high-performance soil stabilization method. PAA-enhanced EICP provides multiple benefits including lengthening of water supply time, localization of cementation reactions, reduction of harmful byproduct ammonium, and achievement of ultrahigh soil strength. Soil crusts we have obtained can sustain up to 4.8 × 10³ kPa pressure, a level comparable to cementitious materials. An ammonium removal rate of 96% has also been achieved. These results demonstrate the potential for hydrogel-assisted EICP to provide effective soil improvement and ammonium mitigation for wind erosion control and other applications.

Evaluation of ammonia-nitrogen removal efficiency from aqueous solutions by ultrasonic irradiation in short sonication periods

In this study, mechanisms and efficiency of ammonia-nitrogen removal from aqueous solutions by ultrasonic irradiation were investigated. Depending on the factors affecting the sonication (initial concentration, initial pH, ultrasonic power density and sonication period), sonication tests were carried out and ammonium-nitrogen removal efficiency by ultrasonic irradiation was determined. In these experiments, ammonia-nitrogen removal efficiency was achieved in the range of 8-64%. In short sonication periods, the best ammonia-nitrogen removal efficiency was achieved at pH 8.2-11. Lower ammonia-nitrogen removal efficiency was observed in high initial ammonia-nitrogen concentration of solutions. It was observed that high initial ammonia-nitrogen concentrations may led to decreased ammonia-nitrogen removal efficiency however quantity of ammonia-nitrogen removal was higher. Because high initial concentration had a negative impact on the sonochemical reactions the heat of cavitation bubbles was reduced. Ammonia-nitrogen removal efficiency was increased with ultrasonic density and sonication period. This study showed that effective ammonia-nitrogen removal could be achieved by the ultrasonic irradiation in short sonication periods (as 60-600 s). Specific cost of ammonia-nitrogen removal by the ultrasonic irradiation from simulated ground water, surface water, wastewater and landfill leachate was also calculated. The specific removal cost was varied between 0.01 and 0.25$/g ammonia-nitrogen.

Eco-friendly superabsorbent composite based on sodium alginate and organo-loess with high swelling properties

A novel superabsorbent composite with high swelling properties was synthesized by the grafted co-polymerization of partially neutralized acrylic acid (AA) onto a sodium alginate (NaAlg) backbone in the presence of organo-loess.

Fabrication of interfacial functionalized porous polymer monolith and its adsorption properties of copper ions

The interfacial functionalized poly (glycidyl methacrylate) (PGMA) porous monolith was fabricated and applied as a novel porous adsorbent for copper ions (Cu(2+)). PGMA porous material with highly interconnected pore network was prepared by concentrated emulsion polymerization template. Then polyacrylic acid (PAA) was grafted onto the interface of the porous monolith by the reaction between the epoxy group on PGMA and a carboxyl group on PAA. Finally, the porous monolith was interfacial functionalized by rich amount of carboxyl groups and could adsorb copper ions effectively. The chemical structure and porous morphology of the porous monolith were measured by Fourier transform infrared spectroscopy and scanning electron microscopy. Moreover, the effects of pore size distribution, pH value, co-existing ions, contacting time, and initial concentrations of copper ions on the adsorption capacity of the porous adsorbents were studied.