Photocatalytic degradation using design of experiments: a review and example of the Congo red degradation

Microfluidic preparation and optimization of (Kollicoat ® IR-b-PCL) polymersome for co-delivery of Nisin-Curcumin in breast cancer application

This work aimed to develop amphiphilic nanocarriers such as polymersome based diblock copolymer of Kollicoat ® IR -block-poly(ε-caprolactone) (Kollicoat ® IR-b-PCL) for potential co-delivery of Nisin (Ni) and Curcumin (CUR) for treatment of breast cancer. To generate multi-layered nanocarriers of uniform size and morphology, microfluidics was used as a new technology. In order to characterise and optimize polymersome, design of experiments (Design-Expert) software with three levels full factorial design (3-FFD) method was used. Finally, the optimized polymersome was produced with a spherical morphology, small particle size (dH < 200 nm), uniform size distribution (PDI < 0.2), and high drug loading efficiency (Ni 78 % and CUR 93 %). Furthermore, the maximum release of Ni and CUR was found to be roughly 60 % and 80 % in PBS, respectively. Cytotoxicity assays showed a slight cytotoxicity of Ni and CUR -loaded polymersome (N- Ni /CUR) towards normal cells while demonstrating inhibitory activity against cancer cells compared to the free drugs. Also, the apoptosis assays and cellular uptake confirmed the obtained results from cytotoxic analysis. In general, this study demonstrated a microfluidic approach for preparation and optimization of polymersome for co-delivery of two drugs into cancer cells.

Congo red dye degradation using Fe-containing mineral as a reactive material derived from waste foundry dust

This study investigated the applicability of industrial waste. The high affinity of Fe-based products is widely used for industrial effluents because of their capability to oxidize contaminants. Waste foundry dust (WFD) is an Fe oxide that has been investigated as a potential reactive material that causes the generation of reactive oxidants. We aimed to investigate the physicochemical properties of WFD and the feasibility in the Fenton oxidation process. The WFD was used as a catalyst for removing Congo red (CR), to evaluate the generation of •OH and dissolution of Fe during the oxidation process. The linkage of •OH generation by WFD with eluted Fe(II) through the Fe dissolution was found. The Fenton oxidation reaction, CR degradation was affected by H2O2 concentration, initial pH, WFD dosage, initial CR concentration, and coexisting anions. The CR degradation efficiency increased with an increase in H2O2 concentration and WFD dosage. In addition, chloride and sulfate in solution promoted CR degradation, whereas carbonate had a negative effect on the Fenton oxidation process. The elution of Fe promotes CR degradation, over three reuse cycles, the degradation performance of the CR decreased from 100 to 81.1%. For the Fenton oxidation process, •OH generation is linked to Fe redox cycling, the surface passivation and Fe complexes interrupted the release of reactive oxidants, which resulted in the degradation of the CR decreased. This study proposed that WFD can serve as catalysts for the removal of CR.

Metal-organic framework heterojunctions for photocatalysis

Heterojunctions combining two photocatalysts of staggered conduction and valence band energy levels can increase the photocatalytic efficiency compared to their individual components. This activity enhancement is due to the minimization of undesirable charge recombination by the occurrence of carrier migration through the heterojunction interface with separated electrons and holes on the reducing and oxidizing junction component, respectively. Metal-organic frameworks (MOFs) are currently among the most researched photocatalysts due to their tunable light absorption, facile charge separation, large surface area and porosity. The present review summarizes the current state-of-the-art in MOF-based heterojunctions, providing critical comments on the construction of these heterostructures. Besides including examples showing the better performance of MOF heterojunctions for three important photocatalytic processes, such as hydrogen evolution reaction, CO2 photoreduction and dye decolorization, the focus of this review is on describing synthetic procedures to form heterojunctions with MOFs and on discussing the experimental techniques that provide evidence for the operation of charge migration between the MOF and the other component. Special attention has been paid to the design of rational MOF heterojunctions with small particle size and controlled morphology for an appropriate interfacial contact. The final section summarizes the achievements of the field and provides our views on future developments.

RSM approach for process optimization of the photodegradation of congo red by a novel NiCo2S4/chitosan photocatalyst

The current study reported a facile co-precipitation technique for synthesizing novel NiCo2S4/chitosan nanocomposite. The photocatalytic activity of the prepared nanocomposite was evaluated using congo red (CR) dye as a target pollutant. The central composite design was employed to examine the impact of different reaction conditions on CR dye degradation. This study selected the pH, photocatalyst loading, initial CR concentration and reaction time as reaction parameters, while the degradation efficiency (%) was selected as the response. A desirability factor of 1 suggested the adequacy of the model. Maximum degradation of 93.46% of 35 ppm dye solution was observed after 60 min of visible light irradiation. The response to surface methodology (RSM) is a helpful technique to predict the optimum reaction conditions of the photodegradation of CR dye. Moreover, NiCo2S4/Ch displayed high recyclability and reusability up to four consecutive cycles. The present study suggests that the prepared NiCo2S4/chitosan nanocomposite could prove to be a viable photocatalyst for the treatment of dye-contaminated wastewater.

Tailoring Vanadium-Based Magnetic Catalyst by In Situ Encapsulation of Tungsten Disulfide and Applications in Abatement of Multiple Pollutants

A magnetic nanocomposite of tungsten and vanadium was employed as a catalyst for the mitigation of water contaminants, including a carcinogenic dye (Congo red, CR), a widely used pesticide (glyphosate), and the bacterial strain Escherichia coli. Additionally, it was subjected to several characterization techniques. X-ray diffraction spectroscopy examination validated the synthesized nanoparticles' crystalline nature, and scanning electron microscopy and energy-dispersive X-ray analysis were employed to examine the morphology and elemental composition of the catalyst. The use of thermogravimetric analysis enabled the elaboration of the thermal behavior of tungsten sulfide-vanadium decorated with Fe2O3 nanoparticles. The experiments were conducted under visible light conditions. The highest levels of photodegradation of 96.24 ± 2.5% for CR and 98 ± 1.8% for glyphosate were observed following a 180 min exposure to visible light at pH values of 6 and 8, respectively. The quantum yields for CR and Gly were calculated to be 9.2 × 10-3 and 4.9 × 10-4 molecules photon-1, respectively. The findings from the scavenger analysis suggest the involvement of hydroxyl radicals in the degradation mechanism. The study evaluated the inhibition of E. coli growth when exposed to a concentration of 0.1 g/10 mL of the photocatalyst, utilizing a 1 mL sample of the bacterial strain. The successful elimination of CR and glyphosate from water-based solutions, along with the subsequent antibacterial experiments, has substantiated the efficacy of the photocatalyst in the field of environmental remediation.

A comprehensive review of bioleaching optimization by statistical approaches: recycling mechanisms, factors affecting, challenges, and sustainability

A serious environmental problem is associated with the accumulation of solid waste on the Earth. Researchers are encouraged to find an efficient and sustainable method to recover highly profitable heavy metals and precious and base metals. Bioleaching is a green method of recovering valuable metals from solid waste. Optimizing the variables and conditions of the bioleaching process is crucial to achieving maximum metal recovery most cost-effectively. The conventional optimization method (one factor at a time) is well-studied. However, it has some drawbacks, such as the necessity of more experiments, the need to spend more time, and the inability to illuminate the synergistic effect of the variables. Optimization studies are increasingly utilizing response surface methodology (RSM) because it provides details about the interaction effects of variables with fewer experiments. This review discusses the application of RSM for bioleaching experiments from other solid wastes. It discusses the Central Composite and Box-Behnken designs as the most commonly used designs for optimizing bioleaching methods. The most influential factors for increasing the heavy metal recovery rate in applying RSM using the bioleaching process are recognized, and some suggestions are made for future research.

Facile Fabrication of Highly Active CeO2@ZnO Nanoheterojunction Photocatalysts

Photocatalyst performance is often limited by the poor separation and rapid recombination of photoinduced charge carriers. A nanoheterojunction structure can facilitate the separation of charge carrier, increase their lifetime, and induce photocatalytic activity. In this study, CeO₂@ZnO nanocomposites were produced by pyrolyzing Ce@Zn metal-organic frameworks prepared from cerium and zinc nitrate precursors. The effects of the Zn:Ce ratio on the microstructure, morphology, and optical properties of the nanocomposites were studied. In addition, the photocatalytic activity of the nanocomposites under light irradiation was assessed using rhodamine B as a model pollutant, and a mechanism for photodegradation was proposed. With the increase in the Zn:Ce ratio, the particle size decreased, and surface area increased. Furthermore, transmission electron microscopy and X-ray photoelectron spectroscopy analyses revealed the formation of a heterojunction interface, which enhanced photocarrier separation. The prepared photocatalysts show a higher photocatalytic activity than CeO₂@ZnO nanocomposites previously reported in the literature. The proposed synthetic method is simple and may produce highly active photocatalysts for environmental remediation.

Removal of the neonicotinoid insecticide acetamiprid from wastewater using heterogeneous photocatalysis

Due to its high solubility in water, a large amount of the neonicotinoid insecticide acetamiprid persisting in the soil of treated crops enters surface water or groundwater. The aim of this study was to investigate the photocatalytic degradation of acetamiprid in an aqueous medium. The experiments were carried out in an annular suspension reactor operating in recirculated batch mode and using a UV-A lamp as the radiation source. An appropriate modification of the commercial TiO₂-P25 photocatalyst was carried out to reduce its band gap energy and electron-hole recombination as well as to extend the visible light range of TiO₂. The photodegradation study was carried out using a three-factor two-stage Box-Behnken experimental design to investigate the main effects and interactions between the operating variables, such as solution pH, initial concentration of acetamiprid, and amount of photocatalyst. The efficiency of the processes was determined by high performance liquid chromatography. The first-order pseudo-reaction kinetic model, as a simplification of the models of Langmuir-Hinshelwood under conditions of relatively low acetamiprid concentration, was applied and the reaction rate constants were estimated. The results of the study showed that the initial concentration of the pollutant was the most influential factor for the photocatalytic degradation process. Using ANOVA analysis, a linear model was established to predict the system behaviour at different operating conditions. The highest conversion and rate constant of acetamiprid degradation were recorded in the experiment with the lowest tested concentration of acetamiprid (2 mg/L), the average concentration of photocatalyst (60 mg) and at pH 8.

Insights on applications of bentonite clays for the removal of dyes and heavy metals from wastewater: a review

In recent decades, increased industrial, agricultural, and domestic activities have resulted in the release of various pollutants into the aquatic systems, which require a reliable and environmentally friendly method to remove them. Adsorption is one of the most cost-effective and sustainable wastewater treatment techniques. A plethora of low-cost bio-based adsorbents have been developed worldwide so far to supplant activated carbon and its high processing costs. Bentonite clays (BCs), whether in natural or modified form, have gained enormous potential in wastewater treatment and have been used successfully as a novel and cost-effective bio-sorbent for removing organic and inorganic pollutants from the liquid suspension. It has become a sustainable solution for wastewater treatment due to its variety of surface and structural properties, superior chemical stability, high capacity for cation exchange, elevated surface area due to its layered structure, non-toxicity, abundance, low cost, and high adsorption capacity compared to other clays. This review encompasses comprehensive literature about various modification techniques and adsorption mechanisms of BCs concerning dyes and heavy metal removal from wastewater. A critical overview of different parameters for optimizing adsorption capacity and regeneration via the desorption technique has also been presented here. Finally, a conclusion has been drawn with some future research recommendations based on technological challenges encountered in industrializing these materials.

Design of biomass-based composite photocatalysts for wastewater treatment: a review over the past decade and future prospects

This investigation applied a systematic review approach on publications covering primary data during 2012-2022 with a focus on photocatalytic degradation of pollutants in aqueous solution by composite materials synthesized with biomass and, at least, TiO₂ and/or ZnO semiconductors to form biomass-based composite photocatalysts (BCPs). After applying a set of eligibility criteria, 107 studies including 832 observations/entries were analyzed. The average removal efficiency and degradation kinetic rate reported for all model pollutants and BCPs were 77.5 ± 21.5% and 0.064 ± 0.174 min^-1, respectively. Principal component analysis (PCA) was applied to analyze BCPs synthesis methods, experimental conditions, and BCPs' characteristics correlated with the removal efficiency and photodegradation kinetics. The relevance of adsorption processes on the pollutants' removal efficiency was highlighted by PCA applied to all categories of pollutants (PCA_pol). The PCA applied to textile dyes (PCA_dyes) and pharmaceutical compounds (PCA_pharma) also indicate the influence of variables related to the composite synthesis (i.e., thermal treatment and time spent on BCPs synthesis) and photocatalytic experimental parameters (catalyst concentration, pollutant concentration, and irradiation time) on the degradation kinetic accomplished by BCPs. Furthermore, the multivariate analysis (PCA_pol) revealed that the specific surface area and the narrow band gap are key characteristics for BCPs to serve as a competitive photocatalyst. The effect of scavengers on pollutants' degradation and the recyclability of BCPs are also discussed, as necessary aspects for scalability trends. Further investigations are recommended to compare the performance of BCPs and commercial catalysts, as well as to assess the costs to treat real wastewater.

Solar photodegradation of irinotecan in water: optimization and robustness studies by experimental design

Irinotecan, a widely prescribed anticancer drug, is an emerging contaminant of concern that has been detected in various aquatic environments due to ineffective removal by traditional wastewater treatment systems. Solar photodegradation is a viable approach that can effectively eradicate the drug from aqueous systems. In this study, we used the design of experiment (DOE) approach to explore the robustness of irinotecan photodegradation under simulated solar irradiation. A full factorial design, including a star design, was applied to study the effects of three parameters: initial concentration of irinotecan (1.0-9.0 mg/L), pH (5.0-9.0), and irradiance (450-750 W/m²). A high-performance liquid chromatography coupled with a high-resolution mass spectrometry (HPLC-HRMS) system was used to determine irinotecan and identify transformation products. The photodegradation of irinotecan followed a pseudo-first order kinetics. In the best-fitted linear model determined by the stepwise model fitting approach, pH was found to have about 100-fold greater effect than either irinotecan concentration or solar irradiance. Under optimal conditions (irradiance of 750 W/m², 1.0 mg/L irinotecan concentration, and pH 9.0), more than 98% of irinotecan was degraded in 60 min. With respect to irradiance and irinotecan concentration, the degradation process was robust in the studied range, implying that it may be effectively applied in locations and/or seasons with solar irradiance as low as 450 W/m². However, pH needs to be strictly controlled and kept between 7.0 and 9.0 to maintain the degradation process robust. Considerations about the behavior of degradation products were also drawn.

MOF-coated upconversion nanoconstructs for synergetic photo-chemodynamic/oxygen-elevated photodynamic therapy

Excessive production of intracellular reactive oxygen species (ROS) can induce apoptosis of cancer cells; however, it is often limited by severe triggering conditions and hypoxic microenvironments of solid tumors. To address these issues, herein, we have designed a MOF-coated upconversion nanoconstruct (UCTSCF, referring to UC@Ce6/TFS@mSiO₂@MIL-100(Cu/Fe)) for synergetic photochemodynamic therapy (PCT)/oxygen-elevated photodynamic therapy (PDT). The MOF (MIL-100(Fe)) coating with Cu-doping was designed to catalyze H₂O₂ overexpression in cancer cells to generate the most cytotoxic ˙OH via chemodynamic therapy (CDT). It is noted that UC, representing 808 nm driven upconversion nanoparticles with high tissue penetration depth/low over-heating effects, was designed to provide intense blue light which can relieve the severe triggering conditions of CDT via PCT. Furthermore, the functional layer of the photosensitizer chlorin e6 (Ce6) and O₂-carrying triethoxy(1H,1H,2H,2H-nonafluorohexyl)silane (TFS) co-doped mesoporous silicon (Ce6/TFS@mSiO₂) can cause oxygen-elevated ¹O₂ production upon 671 nm light irradiation. In such a simple ROS generation nanoplatform, we heighten the antitumor effect via oxygen-elevated synergetic tumor PCT/PDT.

Ammonia quantum tunneling in cold rare-gas He and Ar clusters and factorial design approach for methodology evaluation

Quantum tunneling of the ammonia inversion motion and energy level splittings in He and Ar clusters were investigated. It was found that the double well potential (DWP) in He clusters is symmetrical and that the first layer of He atoms is able to model the system. The calculated tunneling splitting was in good agreement with the experimental, 36.4 and 24.6 cm[Formula: see text] respectively. For NH[Formula: see text] in Ar clusters, the DWP becomes slightly asymmetric, which is enough to decrease the resonance and make the symmetric DWP unable to model the system. An asymmetric potential was used and the result was in excellent agreement with the experimental splitting, of 9.0 and 10.6 cm[Formula: see text] respectively. Non-covalent interactions revealed that the asymmetry is caused by dissimilar interactions in each minimum of the double well potential. The effects of different methodologies were analyzed via a design of experiments approach. For the gas-phase NH[Formula: see text] molecule, only diffuse functions were statistically significant while for the NH[Formula: see text] embedded in He cluster both the MP2 method and polarization functions were significant. This tendency suggests higher order polarization functions may be essential to generate accurate barrier heights.

Recent developments in hydrogels containing copper and palladium for the catalytic reduction/degradation of organic pollutants

The elimination of toxic and hazardous contaminants from different environmental media has become a global challenge, causing researchers to focus on the treatment of pollutants. Accordingly, the elimination of inorganic and organic pollutants using sustainable, effective, and low-cost heterogeneous catalysts is considered as one of the most essential routes for this aim. Thus, many efforts have been devoted to the synthesis of novel compounds and improving their catalytic performance. Recently, palladium- and copper-based hydrogels have been used as catalysts for reduction, degradation, and decomposition reactions because they have significant features such as high mechanical strength, thermal stability, and high surface area. Herein, we summarize the progress achieved in this field, including the various methods for the synthesis of copper- and palladium-based hydrogel catalysts and their applications for environmental remediation. Moreover, palladium- and copper-based hydrogel catalysts, which have certain advantages, including high catalytic ability, reusability, easy work-up, and simple synthesis, are proposed as a new group of effective catalysts.

The elimination of toxic and hazardous contaminants from different environmental media has become a global challenge, causing researchers to focus on the treatment of pollutants.

Bi-functional water-purification materials derived from natural wood modified TiO2 by photothermal effect and photocatalysis

As one of the sustainable and renewable materials, the carbonization of natural wood is generally considered as a low-cost, environmentally friendly method to fabricate carbon materials. Natural wood, by surficial carbonization, can possess an excellent photothermal effect, low heat loss, and easy water transportation in the solar water desalination process based on the unique structures, leading to high solar water desalination performance. Here, we design and construct a composite of commercial P25 nanocrystal-loaded semi-spherical wood with surficial carbonization at the semi-spherical end (P25/wC-s-s), which is beneficial for light harvesting and water evaporation due to the semi-spherical structure-induced large surface area. The composite displays bi-functions of high solar-to-vapour energy efficiency and an intriguing photo-degradation efficiency for organic pollutants in the solar water purification process. The research provides a novel approach to engineering an efficient, stable, and low-cost bi-functional device for the photothermal/photoelectronic conversion of water treatment.

A bifunctional water-purification material is designed by surficial carbonization of the semi-spherical end of a natural wood block and loading of P25 on the lateral surfaces of wood domains.

Colloid synthesis of AgGa(S1-xSex)2 solid solution nanocrystals with composition-dependent crystal phase for efficient photocatalytic degradation of methyl violet

A series of homogeneous AgGa(S1-xSex)2 solid solutions nanocrystals with controllable composition (0 ≤ x ≤ 1) have been successfully prepared through a facile colloidal synthesis approach. Remarkably, they exhibit an...

Application of response surface method in the separation of radioactive material: a review

Response Surface Method (RSM) is one of the most popular and powerful tools for experimental design and optimization. This paper first reviewed the research progress of RSM in the separation and recovery of various radioactive materials, and verified the application of RSM in adsorption isotherm analysis and thermodynamic calculation. The main advantage of RSM in radioactive material separation is the reduction in the number of experiments required, resulting in considerably less radioactive material consumption, secondary waste generation, workload and radiation dose, which is valuable for the research of radioactive material separation.

Experimental Design in Polymer Chemistry-A Guide towards True Optimization of a RAFT Polymerization Using Design of Experiments (DoE)

Despite the great potential of design of experiments (DoE) for efficiency and plannability in academic research, it remains a method predominantly used in industrial processes. From our perspective though, DoE additionally provides greater information gain than conventional experimentation approaches, even for more complex systems such as chemical reactions. Hence, this work presents a comprehensive DoE investigation on thermally initiated reversible addition–fragmentation chain transfer (RAFT) polymerization of methacrylamide (MAAm). To facilitate the adaptation of DoE for virtually every other polymerization, this work provides a step-by-step application guide emphasizing the biggest challenges along the way. Optimization of the RAFT system was achieved via response surface methodology utilizing a face-centered central composite design (FC-CCD). Highly accurate prediction models for the responses of monomer conversion, theoretical and apparent number averaged molecular weights, and dispersity are presented. The obtained equations not only facilitate thorough understanding of the observed system but also allow selection of synthetic targets for each individual response by prediction of the respective optimal factor settings. This work successfully demonstrates the great capability of DoE in academic research and aims to encourage fellow scientists to incorporate the technique into their repertoire of experimental strategies.

Honeycomb-like activated carbon with microporous nanosheets structure prepared from waste biomass cork for highly efficient dye wastewater treatment

Cork, a porous biomass material, is consist of thin-walled hollow prismatic cells arranged into a compact and orderly honeycomb-like structure and could be applied as an adsorption material. Here, cork-activated carbons (CACs) with a fluffy honeycomb-like structure were synthesized by two-step pyrolysis with solid KOH chemical activation to rapidly and efficiently adsorb methylene blue (MB) (maximum wavelength: 664 nm). The structure, morphology and surface functional groups of the CACs were characterized using BET, SEM, and FTIR analysis. The results show that the CACs have a well-developed hierarchical porous structure and an ultra-high specific surface area of 2864.9 m²/g, which would facilitate the efficient diffusion and adsorption of MB molecules onto CACs. MB adsorption performance results show that the CACs have an outstanding maximum MB adsorption capacity (1103.68 mg/g) and fast adsorption kinetics (800 mg/L, 99.8% in 10 min), indicating that CACs possess significant advantages compared with most other adsorbents previously reported. The adsorption mechanism was studied by various kinetic models, isothermal models and thermodynamic models. Langmuir model is the most adapted to describe the adsorption process, indicating that the MB molecules are uniformly adsorbed on CAC's surface in a single layer. Moreover, MB adsorption by the CACs was an endothermic, spontaneous and randomly increasing adsorption. The regeneration test showed that the uptake of MB onto CACs can still reached 580 mg/g after three adsorption-desorption cycles, demonstrating the excellent reusability of CACs. The continuous adsorption performance of MB onto CACs was evaluated by a packed column test, which further confirmed its potential as an adsorbent for dye wastewater purification.

Anionic surfactant assisted copper hydroxide for toxic dye removal from wastewater

Wastewater treatment is the most important criteria that will deliberately reduce the water scarcity and to remove the organic pollutants from water. In this study, pure copper hydroxide (Cu(OH)₂), 1% sodium dodecyl sulphate (SDS) and 2% sodium dodecyl sulphate (SDS) assisted Cu(OH)₂ was prepared through co-precipitation technique. The prepared samples was investigated employing standard characterization studies. The X-Ray diffraction (XRD) pattern was confirmed with JCPDS card # 80-0656 with crystallite size of 25, 23 and 21 nm for pure Cu(OH)₂, 1% SDS and 2% SDS assisted Cu(OH)₂. The bandgap energy obtained for Cu(OH)₂, 1% SDS and 2% SDS assisted Cu(OH)₂ were 2.86 eV, 2.81 eV and 2.72 eV. The narrow bandgap of 2% SDS assisted Cu(OH)₂ enhanced the photocatalytic activity than other two samples. The formation of nanoclusters and nanosheets were confirmed with Scanning Electron Microscopic (SEM) analysis. The thick clumsy nanosheets are formed as large nanoclusters in pure Cu(OH)₂. Addition of SDS reduced the thickness of nanosheets and formed a little cluster. The prepared product photocatalytic performance was examined employing degradation of Methylene Blue (MB) dye. 2% SDS assisted Cu(OH)₂ added MB dye solution was completely degraded with 98% efficiency. The reduce in particle size, high recombination of electron-hole pair with narrow bandgap made the 2% SDS assisted Cu(OH)₂ candidate to give out potential output in eliminating the organic pollutants.

Design of experiments applied to stress testing of pharmaceutical products: A case study of Albendazole

Forced degradation tests are studies used to assess the stability of active pharmaceutical ingredients (APIs) and their formulations. These tests are performed submitting the API under extreme conditions in order to know the main degradation products in a short period of time. The results of these studies are used to assess the degradation susceptibility of APIs and to validate chromatographic analytical methods. However, most of degradation studies are performed using one-factor-at-the-time (OFAT) which does not consider the interactions between degradation variables. This work proposes the use of Design of Experiment (DoE) approach in forced degradation of albendazole (ABZ). It was used a central composite design (CCD) to evaluate the forced degradation in a multivariate way. Experiments were performed taking into account the variables pH, temperature, oxidizing agent (H₂O₂) and UV radiation. It was verified the influence of the variables and their interactions on the ABZ degradation. The ABZ oxidation showed to be the main degradation route for ABZ, which is strongly influenced by the temperature. The hydrolysis was relevant at alkaline medium and high temperature. LC-IT-MSⁿ was used to identify the degradation products. It was found three known degradation products (albendazole-2-amino, albendazole sulfoxide and albendazole sulfone) and a new derivate of albendazole molecule (albendazole sulfoxide with a chlorine). This last one was isolated and characterized by UPLC-QToF-MS and NMR analyses.

A novel electrocatalytic filtration system with carbon nanotube supported nanoscale zerovalent copper toward ultrafast oxidation of organic pollutants

In this study, we designed an integrated electrochemical filtration system for catalytic activation of peroxymonosulfate (PMS) and degradation of aqueous microcontaminants. Composites of carbon nanotube (CNT) and nanoscale zero valence copper (nZVC) were developed to serve as high-performance catalysts, electrode and filtration media simultaneously. We observed both radical and nonradical reaction pathways, which collectively contributed to the degradation of model pollutants. Congo red was completely removed via a single-pass through the nZVCCNT filter (τ <2 s) at neutral pH. The rapid kinetics of Congo red degradation were maintained across a wide pH range (from 3.0-7.0), in complicated matrixes (e.g., tap water and lake water), and for the degradation of a wide array of persistent organic contaminants. The superior activity of nZVCCNT stems from the boosted redox cycles of Cu²⁺/Cu⁺ in the presence of an external electric field. The flow-through design remarkably outperformed the conventional batch system due to the convection-enhanced mass transport. Mechanism studies suggested that the carbonyl group and electrophilic oxygen of CNT served as electron donor and electron acceptor, respectively, to activate PMS to generate •OH and ¹O₂via one-electron transport. The electron-deficient Cu atoms are prone to react with PMS via surface hydroxyl group to produce reactive intermediates (Cu²⁺-O-O-SO₃^-), and then ¹O₂ will be generated by breaking the coordination bond of the metastable intermediate. The study will provide a green strategy for the remediation of organic pollution by a highly efficient and integrated system based on catalytic oxidation, electrochemistry, and nano-filtration techniques.

Mesoporous ferromagnetic manganese ferrite nanoparticles for enhanced visible light mineralization of azoic dye into nontoxic by-products

In this study, a one pot facile synthesis of ferromagnetic manganese ferrite nanoparticles (MnFe₂O₄) was carried out using chemical co-precipitation method for mineralization of azo dye (Congo red (CR)) in aqueous solution under visible light irradiation. The synthesized MnFe₂O₄ nanoparticles were highly crystalline and showed face-centred cubic (FCC) structure with average particle size of 58 ± 4 nm. The BET analysis of the MnFe₂O₄ nanoparticles revealed the mesoporous distribution of material with high surface area can provide large electro active sites and short diffusion paths for the transport of ions which plays a vital role in the photocatalytic degradation of CR. The point of zero charge (pH_PZC) was observed to be 6.7 indicating favourable condition for material-anionic dye interaction. The XPS studies revealed that the large amounts of oxygen vacancies were produced due to the defects in the lattice oxygen. The MnFe₂O₄ nanoparticles mineralised 98.3 ± 0.2% of 50 mg/L CR within 30 min when tested in photocatalytic reactor under 565 nm. The particles were recoverable under the influence of an external magnet after the photocatalytic reaction and were reusable. The recovered nanoparticles showed 96% of CR degradation efficiency even after five cycles of reuse. The by-product analysis with GC-MS indicated mineralization of CR into simple alcohols and acids. The aqueous solution containing mineralised CR was nontoxic to Trigonella foenumgraecum and Vigna mungo seeds and favoured increased germination, plumule and radicle length when compared to untreated CR.

Oxygen-rich bismuth oxybromide nanosheets coupled with Ag2O as Z-scheme nano-heterostructured plasmonic photocatalyst: Solar light-activated photodegradation of dye pollutants

In this research to enhance the photocatalytic activity of Bi₂₄O₃₁Br₁₀, precipitation fabrication of the Z-scheme heterojunction with Ag-Ag₂O has been investigated. The characterizations were carried out by XRD, FESEM, TEM, EDX, BET-BJH, DRS and pH_pzc analyzes. The Ag-Ag₂O/Bi₂₄O₃₁Br₁₀ Z-scheme heterojunction nanophotocatalyst with weighted ratio of 3:1 exhibited the wide absorption in the visible light region and displayed the high photocatalytic activity for the photodegradation of acid orange 7 (96.5%, 94.1% and 90% for 10, 20 and 60 mg/L, respectively after 120 min) and eosin yellow (for 10 mg/L: 81.5%) compared to the other composites and pure Bi₂₄O₃₁Br₁₀ and Ag-Ag₂O samples. The highly enhanced photocatalytic activity of Ag-Ag₂O/Bi₂₄O₃₁Br₁₀ (3:1) was assigned to the surface plasmon resonance effect of silver nanoparticles, high solar-light-response and the structure of Z-scheme heterojunction, which effectively reduces the recombination of the photogenerated charge carriers. Moreover Ag-Ag₂O/Bi₂₄O₃₁Br₁₀(3:1) Z-scheme heterojunction nanophotocatalyst exhibited the good photocatalytic activity even after 4 runs.

State-of-the-art and current challenges for TiO2/UV-LED photocatalytic degradation of emerging organic micropollutants

The development of ultraviolet light-emitting diodes (UV-LED) opens new possibilities for water treatment and photoreactor design. TiO₂ photocatalysis, a technology that has been continuously drawing attention, can potentially benefit from LEDs to become a sustainable alternative for the abatement of organic micropollutants (OMPs). Recently reported data on photocatalytic degradation of OMPs and their parameters of influence are here critically evaluated. The literature on OMP degradation in real water matrices, and at environmentally relevant concentrations, is largely missing, as well as the investigations of the impact of photoreactor design in pollutant degradation kinetics. The key factors for reducing UV-LED treatment technology costs are pointed out, like the increase in external quantum and wall-plug efficiencies of UV-LEDs compared to other technologies, as well as the need for an appropriate design optimizing light homogeneity in the reactor. Controlled periodic illumination, wavelength coupling and H₂O₂ addition are presented as efficiency enhancement options. Although electrical energy per order (E_EO) values for UV-LED photocatalysis have decreased to the range of traditional mercury lamps, values are still not low enough for practical employment. Moreover, due to the adoption of high initial OMP concentration in most experiments, it is likely that most literature E_EO values are overestimated. Given the process characteristics, which are favoured by translucent matrices and small diameters for more homogenous light distribution and better transportation of radicals, innovative reactor designs should explore the potential of point-of-use applications to increase photocatalysis applicability at large scale.

Landfill leachate wastewater treatment to facilitate resource recovery by a coagulation-flocculation process via hydrogen bond

Recent trend to recover value-added products from wastewater calls for more effective pre-treatment technology. Conventional landfill leachate treatment is often complex and thus causes negative environmental impacts and financial burden. In order to facilitate downstream processing of leachate wastewater for production of energy or value-added products, it is pertinent to maximize leachate treatment performance by using simple yet effective technology that removes pollutants with minimum chemical added into the wastewater that could potentially affect downstream processing. Hence, the optimization of coagulation-flocculation leachate treatment using multivariate approach is crucial. Central composite design was applied to optimize operating parameters viz. Alum dosage, pH and mixing speed. Quadratic model indicated that the optimum COD removal of 54% is achieved with low alum dosage, pH and mixing speed of 750 mgL^-1, 8.5 and 100 rpm, respectively. Optimization result showed that natural pH of the mature landfill leachate sample is optimum for alum coagulation process. Hence, the cost of pH adjustment could be reduced for industrial application by adopting optimized parameters. The inherent mechanism of pollutant removal was elucidated by FTIR peaks at 3853 cm^-1 which indicated that hydrogen bonds play a major role in leachate removal by forming well aggregated flocs. This is concordance with SEM image that the floc was well aggregated with the porous linkages and amorphous surface structure. The optimization of leachate treatment has been achieved by minimizing the usage of alum under optimized condition.

Current developments and future trends in photocatalytic glycerol valorization: process analysis

Challenges and opportunities in photocatalytic glycerol valorization to hydrogen and value-added liquid products: process analysis and parametric study.

Ca2+ mediated mechanism of octa-brominated dioxin/furan formation via BDE-209 thermolysis: Introducing the Mayer bond order difference

Polybrominated dibenzo-p-dioxins/dibenzofurans (PBDD/Fs) that form during industrial thermal processes, such as the cement kiln co-processing of BDE-209, are highly toxic contaminants. Nevertheless, the formation mechanisms of octa-brominated dioxins/furans (OBDD/Fs), most PBDD/F congeners, and one precursor of the more toxic lower PBDD/Fs from BDE-209 have received little attention. In cement kiln co-processes, the Ca²⁺-mediated regulation of OBDD/F formation is still debated. In this study, simulation experiments revealed that the average brominating degree of PBDD/Fs was 7.8, indicating that OBDD/Fs are dominant congeners (93.6 % median). Density functional theory (DFT) calculations found a new transition state (TS1) with a lower energy barrier than that found in a previous study. Three major OBDD/F formation reactions suggested that the presence of Ca²⁺ was thermodynamically beneficial to the formation of OBDD/Fs. This promotion effect can be attributed to the transfer of electron density leading to a change in the Mayer bond order (MBO) among elements when Ca²⁺ was bound. Intriguingly, in the transition state structures of the Ca²⁺-bound and Ca²⁺-free systems, the MBO difference among the old and new bonds can reveal the difficulty of Ca²⁺-mediated OBDD/F formation reactions from BDE-209.

Pathways and influential factors study on the formation of PBDD/Fs during co-processing BDE-209 in cement kiln simulation system

The thermal processes of cement kilns are sources of polybrominated dibenzofurans and dioxins (PBDD/Fs); however, when co-processing decabromodiphenyl ether (BDE-209) soil in cement kilns, very few reports have investigated the mechanism of PBDD/Fs formation from BDE-209. Therefore, the pathways and factors that influence the formation of PBDD/Fs were investigated using Box-Behnken design (BBD) of the response surface methodology (RSM) at lab-scale. The PBDEs, HBr/Br₂ and PBDD/Fs emissions in flue gas from the simulated thermal process were analyzed using gas chromatography/mass spectroscopy (GC/MS), high-resolution gas chromatography/high-resolution mass spectrometry (HRGC/HRMS), and ion chromatography (IC). Density functional theory (DFT) was also used to further discuss the formation of PBDD/Fs. The major products of BDE-209 thermal decomposition in flue gas were 97.1% HBr/Br₂ (a.v. 26.6%/70.6%) > 2.7% PBDEs >0.2% PBDD/Fs. Formation of precursors were the main pathways for PBDD/Fs, and those precursors were dominated by higher-brominated PBDEs (heptã deca-BDEs); debromination of BDE-209 was also a crucial pathway for the formation of PBDD/Fs throughout the thermal process. Interestingly, it was easier to form HpBDD/Fs from OBDD/Fs than from PBDEs. The O₂ percentage and interaction factors of O₂ percentage, temperature, and CaCO₃ percentage have the largest influence on PBDD/Fs emissions and formation.

Degradation of 1,2-dichloroethane by photocatalysis using immobilized PAni-TiO2 nano-photocatalyst

1,2-Dichloroethane is one of the most hazardous environmental pollutants in wastewaters. It is mainly used to produce vinyl chloride monomer, the major precursor for PVC production. It is determined to be a probable human carcinogen and has been listed as a priority pollutant by the United States Environmental Protection Agency. Due to high chemical stability and low biodegradability of 1,2-dichloroethane, heterogeneous photocatalysis was used for degradation of this chlorinated hydrocarbon. PAni-TiO₂ nanocomposite was synthesized by in situ deposition oxidative polymerization method and immobilized on glass beads by a modified dip coating and heat attachment method. The characteristics of synthesized PAni-TiO₂ nanoparticles were confirmed using the results of morphology tests including Fourier-transform infrared spectra, X-ray diffraction patterns, particle size analysis, UV-Visible spectrophotometer, scanning electron microscope, and energy-dispersive X-ray spectroscopy. The performance of photocatalytic degradation of 1,2-dichloroethane using synthesized PAni-TiO₂ nanocomposite in a designed and constructed pilot scale packed bed recirculating photocatalytic reactor under xenon light irradiation was investigated. The response surface methodology based on the central composite design was used to evaluate and optimize the effect of 1,2-dichloroethane concentration, residence time, pH, and coating mass as independent variables on the photocatalytic degradation of 1,2-dichloroethane as the response function. Results showed that actual and predicted results were well fitted with R² of 0.9870, adjusted R² of 0.9718, and predicted R² of 0.9422. The optimum conditions for 1,2-dichloroethane photocatalytic degradation were the 1,2-dichloroethane concentration of 250 mg/L, the residence time of 240 min, pH of 5, and coating mass of 0.5 mg/cm², which resulted in 88.84% photocatalytic degradation. Kinetic of the photocatalytic degradation at optimal condition follows the Langmuir-Hinshelwood first-order reaction with k = 0.0095 min^-1 with R² = 0.9455. Complete photocatalytic degradation of 1,2-DCE was achieved after 360 min.