Adsorption isotherms and kinetics studies of malachite green on chitin hydrogels

Preparation of chitin/MXene/poly(L-arginine) composite aerogel spheres for specific adsorption of bilirubin

Currently, hemoperfusion is clinically the most rapid and effective treatment for removing toxins from the blood. The core of hemoperfusion is the sorbent inside the hemoperfusion device. Due to the complex composition of the blood, adsorbents tend to adsorb substances such as proteins in the blood (non-specific adsorption) while adsorbing toxins. Hyperbilirubinemia is caused by excessive levels of bilirubin in the human blood, causing irreversible damage to the patient's brain and nervous system, and even leading to death. High adsorption and high biocompatibility adsorbents with specific bilirubin adsorption are urgently needed to treat hyperbilirubinemia. Herein, poly(L-arginine) (PLA) which can specifically adsorb bilirubin, was introduced into chitin/MXene (Ch/MX) composite aerogel spheres. Ch/MX/PLA prepared by supercritical CO₂ technology had higher mechanical properties than Ch/MX and can withstand 50,000 times its own weight. The in vitro simulated hemoperfusion test showed that the adsorption capacity of Ch/MX/PLA was as high as 596.31 mg/g, which was 15.38 % higher than that of Ch/MX. Binary and ternary competitive adsorption tests showed that Ch/MX/PLA also had good adsorption capacity in the presence of a variety of interfering molecules. In addition, hemolysis rate testing and CCK-8 testing confirmed that Ch/MX/PLA had better biocompatibility and hemocompatibility. Ch/MX/PLA can meet the required properties of clinical hemoperfusion sorbents and has the ability to produce mass production. It has good application potential in the clinical treatment of hyperbilirubinemia.

Reactive Green 19 dye-ligand immobilized on the aminated nanofiber membranes for efficient adsorption of lysozyme: Process development and optimization in batch and flow systems

The performance of lysozyme adsorption by the aminated nanofiber membrane immobilized with Reactive Green 19 (RG19) dyes was evaluated in batch and flow systems. The physicochemical properties of the dye-immobilized nanofiber membrane were characterized. The parameters of batch-mode adsorption of lysozyme (e.g., pH, initial dye concentration, and lysozyme concentration) were optimized using the Taguchi method. In a flow process, the factors influencing the dynamic binding performance for lysozyme adsorption in the chicken egg white (CEW) solution include immobilized dye concentration, adsorption pH value, feed flow rate, and feed CEW concentration. The impact of these operating conditions on the lysozyme purification process was investigated. Under optimal conditions, the recovery yield and purification factor of lysozyme achieved from the one-step adsorption process were 98.52% and 143 folds, respectively. The dye-affinity nanofiber membrane also did not exhibit any significant loss in its binding capacity and purification performance after five consecutive uses.

Bilirubin Removal by Polymeric Adsorbents for Hyperbilirubinemia Therapy

Hyperbilirubinemia, presenting as jaundice, is a life-threatening critical illness in newborn babies and acute severe hepatic failure patients. Over the past few decades, extracorporeal hemoadsorption by adsorbent therapy has been widely applied in the treatment of hyperbilirubinemia. The capability of hemoadsorption depends on the adsorbents. Most of the clinically used bilirubin adsorbents are made up of styrene/divinylbenzene copolymer and quaternary ammonium salt, which usually have poor biocompatibility and weak mechanical strength. To overcome the drawbacks of commercial polymer adsorbents, advanced synthetic and natural polymers with/without nanomaterials have been designed, and novel adsorbent fabrication technologies have also been developed. In this review, the adsorption mechanism of bilirubin adsorbents has been summarized, which is the basic criterion in adsorbent development. Furthermore, the preparation method, adsorption mechanism, relative merits and practicability of the emerging bilirubin adsorbents have been evaluated. Based on the existing studies, this work highlights the future direction of the efforts on how to design and develop bilirubin adsorbents with good overall clinical performance. Perhaps this study can change traditional perspectives and propose new strategies for bilirubin clearance from the aspects of pathogenic mechanisms, metabolic pathways, and material-based innovation.

Removal of As(V) from aqueous solution using modified Fe3O4 nanoparticles

The removal of arsenic contamination from the aqueous environment is of great importance in the conservation of the Earth's water resources, and surfactants are a promising material used to modify magnetic nanoparticles to improve adsorption properties. Therefore, it is important to develop efficient and selective adsorbents for arsenic. Surface modification of Fe₃O₄ was carried out using anionic, cationic and zwitterionic surfactants to obtain composite Fe₃O₄@SDS, Fe₃O₄@CTAB, Fe₃O₄@SNC 16 and Fe₃O₄@NPC 16 (collectively referred to as Fe₃O₄@surfactants). The synthesized composite Fe₃O₄@surfactants magnetic nanoparticles were characterized by XRD, TEM and FTIR. The As(V) removal characteristics of the composite magnetic nanoparticles from the aqueous solution were evaluated by adsorption batch experiments which indicated the possibility of effective application of the surfactant-modified Fe₃O₄ magnetic nanoparticles for the removal of As(V) from aqueous solution. The adsorption equilibrium of the composites was reached in 30 min and the kinetic data followed the pseudo-second-order model. Langmuir equation could represent the adsorption isotherm data very well. Moreover, under the identical conditions, Fe₃O₄@CTAB showed maximum capacity of adsorption for As(V) (55.671 mg g^-1), with its removal efficiency being much higher than that of the other composites. In addition, the Fe₃O₄@surfactants composite magnetic nanoparticles retained 93.5% of its initial arsenic removal efficiency even after re-using it five times. The mechanism of arsenic adsorption by Fe₃O₄@surfactants composite magnetic nanoparticles was proved to be complexation via electrostatic attraction, which was mainly innersphere in nature.

Chitin-Based Magnesium Oxide Biocomposite for the Removal of Methyl Orange from Water

In this work, a cost-effective chitin-based magnesium oxide (CHt@MgO) biocomposite with excellent anionic methyl orange (MO) dye removal efficiency from water was developed. The CHt@MgO biocomposite was characterized by FT-IR, XRD, SEM-EDX, and TGA/DTG. Results proved the successful synthesis of CHt@MgO biocomposite. Adsorption of MO on the CHt@MgO biocomposite was optimized by varying experimental conditions such as pH, amount of adsorbent (m), contact time (t), temperature (T), and initial MO concentration (C_o). The optimized parameters for MO removal by CHt@MgO biocomposite were as follows: pH, 6; m, 2 g/L; t, 120 min. Two common isotherm models (Langmuir and Freundlich) and three kinetic models (pseudo-first-order (PFO), pseudo-second-order (PSO), and intraparticle diffusion (IPD)) were tested for experimental data fitting. Results showed that Langmuir and PFO were the most suitable to respectively describe equilibrium and kinetic results on the adsorption of MO adsorption on CHt@MgO biocomposite. The maximum Langmuir monolayer adsorption capacity (q_m) on CHt@MgO biocomposite toward MO dye was 252 mg/g at 60 °C. The reusability tests revealed that CHt@MgO biocomposite possessed high (90.7%) removal efficiency after the fifth regeneration cycle.

Insight into the removal of vanadium ions from model and real wastewaters using surface grafted zirconia-based adsorbents: Batch experiments, equilibrium and mechanism study

This study concerns the fabrication of CTAB- and N,N-dimethyltetradecylamine-grafted zirconia and evaluation of their ability to adsorb vanadium ions. The effectiveness of ZrO₂ functionalization and the different nature of the modifiers used were confirmed by differences in the porosity (ZrO₂: S_BET = 347 m²/g; ZrO₂-CTAB: S_BET = 375 m²/g, ZrO₂-NH⁺: S_BET = 155 m²/g), types of functional groups, and isoelectric points (the ZrO₂ and CTAB-modified samples have IEPs = 3.8 and 3.9, ZrO₂-NH⁺ has IEP = 7.1) of the prepared adsorbents. The designed materials were tested in batch adsorption experiments involving the removal of vanadium ions from model wastewaters at various process parameters, among which pH proved to be the most important. Based on equilibrium and kinetic evaluations, it was proved that the sorption of V(V) ions followed pseudo-second-order and intraparticle diffusion models, and the data were better fitted to the Langmuir model, suggesting the following order of the sorbents in terms of favorability for V(V) ion adsorption: ZrO₂-NH⁺ > ZrO₂ > ZrO₂-CTAB. The estimated maximum monolayer capacity of ZrO₂-NH⁺ for V(V) (87.72 mg/g) was the highest among the tested materials. Additionally, it was confirmed that adsorption of V(V) ions onto synthesized materials is a heterogeneous, exothermic, and spontaneous reaction, as evidenced by the calculated values of thermodynamic parameters. The key goals included the transfer of experimental findings obtained using model solutions to the adsorption of V(V) ions from solutions arising from the leaching process of spent catalysts. The highest adsorption efficiencies of 70.8% and 47.5% were recorded for the ZrO₂-NH⁺ material in acidic solution; this may be related to the protonization of -NH⁺ groups, which favors the sorption of V(V) ions. Based on desorption tests as well as the results of infrared and X-ray photoelectron spectroscopy, irrespective of the process conditions, the physical nature of the adsorbent/adsorbate interaction was confirmed.

Green synthesis of Mn3O4 nanoparticles using Costus woodsonii flowers extract for effective removal of malachite green dye

The pollution of organic dyes such as malachite green is one of the globally critical issues, calling for efficient mitigation methods. Herein, we developed green Mn₃O₄ nanoparticles synthesized using natural compounds extracted from Costus woodsonii flowers under an ultrasound-assisted mode. The materials were characterized using several physicochemical techniques such as Fourier-transform infrared spectroscopy, X-ray diffraction, Energy-dispersive X-ray spectroscopy, scanning electron microscopy, Raman spectroscopy, and N₂ adsorption desorption isotherm measurement. The X-ray diffraction and N₂ isotherm plots confirmed the presence of tetragonal γ-Mn₃O₄ phase and mesoporous structure, respectively. Carbonyl groups derived from flavonoids or carboxylic compounds were found in the surface of green Mn₃O₄ nanoparticles. The effect of pH, contact time, dose, and concentration on the adsorption of malachite green over green Mn₃O₄ was carried out. The maximum malachite green adsorption capacity for green Mn₃O₄ nanoparticles was 101-162 mg g^-1. Moreover, kinetic and isotherm adsorption of malachite green obeyed Langmuir (R_adj.² = 0.980-0.995) and pseudo first-order models (R_adj.² = 0.996-1.00), respectively. Adsorption of malachite green over green Mn₃O₄ was a thermodynamically spontaneous process due to negative Gibbs free energy values (ΔG^ο < 0). Green Mn₃O₄ nanoparticles offered a high stability through the FR-IR spectra analysis. With a good recyclability of 4 cycles, green Mn₃O₄ nanoparticles can be used as potential adsorbent for removing malachite green dye from water.

Indole Facilitates Antimicrobial Uptake in Bacteria

Indole signaling in bacteria plays an important role in antibiotic resistance, persistence, and tolerance. Here, we used the nonlinear optical technique, second-harmonic light scattering (SHS), to examine the influence of exogenous indole on the bacterial uptake of the antimicrobial quaternary ammonium cation (qac), malachite green. The transport rates of the antimicrobial qac across the individual membranes of Escherichia coli and Pseudomonas aeruginosa, as well as liposomes composed of the polar lipid extract of E. coli, were directly measured using time-resolved SHS. Whereas exogenous indole was shown to induce a 2-fold increase in the transport rate of the qac across the cytoplasmic membranes of the wild-type bacteria, it had no influence on a knockout strain of E. coli lacking the tryptophan-specific transport protein (Δmtr). Likewise, indole did not affect the transport rate of the qac diffusing across the liposome membrane. Our findings suggest that indole increases the bacterial uptake of antimicrobials through an interaction with the Mtr permease.

Chitin/egg shell membrane@Fe3O4 nanocomposite hydrogel for efficient removal of Pb2+ from aqueous solution

The development of adsorbents by using the byproducts or waste from large-scale industrial and agricultural production is of great significance, and is considered to be an economic and efficient strategy to remove the heavy metals from polluted water. In this work, a novel chitin/EM@Fe₃O₄ nanocomposite hydrogel was obtained from a NaOH/urea aqueous system, where the proteins of egg shell membrane and Fe₃O₄ nanoparticles were chemically bonded to chitin polymer chains with the help of epichlorohydrin. Due to the existence of a large number of –NH₂, –OH, –CONH–, –COOH and hemiacetal groups, the adsorption efficiency for Pb²⁺ into the absorbent was dramatically enhanced. The experimental results revealed that the adsorption behavior strongly depends on various factors, such as initial pH, initial Pb²⁺ concentration, incubation temperature and contact time. The kinetic experiments indicated that the adsorption process for Pb²⁺ in water solution agreed with the pseudo-second-order kinetic equation. The film diffusion or chemical reaction is the rate limiting process in the initial adsorption stage, and the adsorption of Pb²⁺ into the nanocomposite hydrogel can well fit the Langmuir isotherm. Thermodynamic analysis demonstrated that such adsorption behaviors were dominated by an endothermic (ΔH° > 0) and spontaneous (ΔG° < 0) process.

A novel kind of chitin/EM@Fe₃O₄ nanocomposite hydrogel derived from the biowastes of egg shell membrane and chitin was successfully prepared for efficient removal of Pb²⁺ from wastewater solution.

Biocompatible Composite Microspheres of Chitin/Ordered Mesoporous Carbon CMK3 for Bilirubin Adsorption and Cell Microcarrier Culture

Extra bilirubin in the blood can provoke serious illness in patients with severe liver disease. Hemoperfusion is an effective method to remove the extra bilirubin, but its application is limited by the low adsorption efficiency and poor biocompatibility of available adsorbent materials. In this study, chitin/ordered mesoporous carbon CMK3 (Ch/CMK3) microspheres were successfully prepared. Results of characterization experiments indicated that these composite microspheres possess a multilayered porous nanofibrous structure with an extremely large specific surface area (300.19 m² g^-1 ) and large pore size. Notably, the Ch/CMK3 microspheres demonstrated a high bilirubin adsorption capacity (228.19 mg g^-1 ) in phosphate buffer solution, and an outstanding bilirubin removal ratio (76.78%±4.40%) in the plasma of rabbits with hyperbilirubinemia without affecting the protein components. More importantly, the Ch/CMK3 microspheres showed no effect on other blood components, no cytotoxicity, and no systemic toxicity to mice. Cell coculture experiments revealed that the microspheres could provide a three-dimensional (3D) space to promote cell adhesion, proliferation, and nutrient exchange. These Ch/CMK3 microspheres featuring a strong ability for bilirubin adsorption and good biocompatibility could be a promising candidate in biomedical applications such as hemoperfusion, cell microcarrier, and 3D tissue engineering. This article is protected by copyright. All rights reserved.

Optimization of the spontaneous adsorption of food colors from aqueous medium using functionalized Chitosan/Cinnamaldehyde hydrogel

Hydrogels are considered as practical and proficient materials in adsorption and removal of soluble lethal molecules from aqueous system. They are also rapid-decomposable and economical materials besides their diverse preventive claims. In current study, Cinnamaldehyde (C), a natural defensive compound and Chitosan (Ch), natural occurring bio-macromolecule are considered to develop bio-inspired hydrogel (ChC). The structural and surface characteristics of ChC (¹³C solid state NMR, FT-IR, UV-Vis and SEM) are investigated to confirm the successful grafting. The origami of gelation in ChC performs an excellent adsorption activity towards food dyes, Carmoisine (CA) and Tartrazine (TA), which are contaminated by the accumulation during excess release from catering and chemical industries in aqueous system. The adsorption performance is thoroughly screened by varying the pH, ChC dosage, dye concentration, contact time and temperature in aqueous system. Thermodynamic and Kinetics study suggest the natural tendency of adsorption with a good reusability up to 3 cycles. The main mechanism for spontaneous adsorption is initiated by capturing of TA/CA in porous surface followed by the ionic interactions and formation of H-bondings. ChC based adsorption is an excellent and potential approach to control the toxicants for the water-pollution and water-preservation.

Kinetic and Thermodynamic Studies of Lysozyme Adsorption on Cibacron Blue F3GA Dye-Ligand Immobilized on Aminated Nanofiber Membrane

The polyacrylonitrile (PAN) nanofiber membrane was prepared by the electrospinning technique. The nitrile group on the PAN nanofiber surface was oxidized to carboxyl group by alkaline hydrolysis. The carboxylic group on the membrane surface was then converted to dye affinity membrane through reaction with ethylenediamine (EDA) and Cibacron Blue F3GA, sequentially. The adsorption characteristics of lysozyme onto the dye ligand affinity nanofiber membrane (namely P-EDA-Dye) were investigated under various conditions (e.g., adsorption pH, EDA coupling concentration, lysozyme concentration, ionic strength, and temperature). Optimum experimental parameters were determined to be pH 7.5, a coupling concentration of EDA 40 μmol/mL, and an immobilization density of dye 267.19 mg/g membrane. To understand the mechanism of adsorption and possible rate controlling steps, a pseudo first-order, a pseudo second-order, and the Elovich models were first used to describe the experimental kinetic data. Equilibrium isotherms for the adsorption of lysozyme onto P-EDA-Dye nanofiber membrane were determined experimentally in this work. Our kinetic analysis on the adsorption of lysozyme onto P-EDA-Dye nanofiber membranes revealed that the pseudo second-order rate equation was favorable. The experimental data were satisfactorily fitted by the Langmuir isotherm model, and the thermodynamic parameters including the free energy change, enthalpy change, and entropy change of adsorption were also determined accordingly. Our results indicated that the free energy change had a negative value, suggesting that the adsorption process occurred spontaneously. Moreover, after five cycles of reuse, P-EDA-Dye nanofiber membranes still showed promising efficiency of lysozyme adsorption.

Applications of chitin and chitosan based biomaterials for the adsorptive removal of textile dyes from water - A comprehensive review

The presence of pollutants in the water bodies deteriorate the water quality and make it unfit for use. From an environmental perspective, it is essential to develop new technologies for the wastewater treatment and recycling of dye contaminated water. The surface modified chitin and chitosan biopolymeric composites based adsorbents, have an important role in the toxic organic dyes from removal wastewater. The surface modification of biopolymers with various organics and inorganics produces more active sites at the surface of the adsorbent, which enhances dye and adsorbent interaction more reliable. Herein, the work brought in the thought of the application of various chitin and chitosan composites in wastewater remediation and suggested the versatility in composites for the development of rapid, selective and effective removal processes for the detoxification of a variety of organic dyes. It further emphasizes the existing obstruction and impending prediction for the deprivation of dyes via adsorption techniques.

Integrated experimental and theoretical insights for Malachite Green Dye adsorption from wastewater using low cost adsorbent

Water pollution is one of the problems that threaten humanity, and to confront it with only experimental procedures is not enough. It is necessary to integrate both practical methods and theoretical calculations to achieve decontamination with the most accurate interpretation. Hence, discussing the experimental mechanism study of Malachite Green (MG) dye adsorption with the help of the application of density functional theory (DFT) calculations is the main goal of this article. The experimental results affirmed that the preparation of γ-Al₂O₃ by precipitation method using (NH₄)₂CO₃ improved the porosity, the surface capability, and the adsorbent capacities (q_max = 210 mg/g) at optimum condition compared with the previous studies. Kinetic and equilibrium studies showed that the adsorption follows the pseudo-second-order model and Freundlich isotherm model, respectively. Also, the calculated and observed thermodynamic parameters exerted positive values of ΔH° and ΔS°, which translates into an endothermic process with increasing disorder of the system. Theoretical calculations at DFT- B3LYP/6-31G (d,P) level of theory were calculated to show the selectivity of using the cationic form of MG in the experimental measurements to find the interaction mechanism. The electronic structure and intramolecular charge transfer of MG, its cationic form and the complex of MG-Al were investigated theoretically at the B3LYP/6-31 G (d,p) level of theory. The equilibrium geometries of MG, its cationic form and the complex of MG-Al were determined, and it was found that these geometries are non-planar. The E_HOMO and E_LUMO energies can be used to calculate the global properties; chemical hardness (η), softness (S) and electronegativity (χ). The calculated non-linear optical parameters (NLO) of the studied compounds, the electronic dipole moment (μ), first-order hyperpolarizability (β), the hyper-Rayleigh scattering (β_HRS) and the depolarization ratio (DR), showed promising optical properties. Finally, the computational and the experimental results indicated that the adsorption efficiency of MG from wastewater was directly associated with the dye electrophilicity power.

Adsorption of azo dyes by a novel bio-nanocomposite based on whey protein nanofibrils and nano-clay: Equilibrium isotherm and kinetic modeling

Excessive discharge of synthetic azo dyes into the aquatic ecosystem is a global concern. Here, we develop a green approach to remediate dye pollutants by fabricating an easily separable bio-nanocomposite, based on nanofibrils from whey protein concentrate together with montmorillonite. The nanocomposite was characterized using scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction and surface area analysis. Nanofibrils lead to a uniform dispersion of montmorillonite in the matrix and also reinforce the nanocomposite. The adsorption efficacy was monitored using cationic (Chrysoidine-G, Bismarck brown-R), reactive (reactive black-5, reactive orange-16), acidic (acid red-88, acid red-114) and direct (direct violet-51, Congo red) dyes. The nanocomposite adsorbed different dyes with different kinetics, cationic dyes quicker and reactive dyes slower. Greater than 93% of Chrysoidine-G was adsorbed over a wide range of dye concentration and pH. Acidic pH and higher temperature are more favorable for the process. Equilibrium adsorption data were reasonably fitted with a linear (Nernst) isotherm model indicating the existence of an unlimited number of adsorption sites which is consistent with the high experimental uptake of 731 mg/g. Kinetic data were well-described by pseudo-second-order and intra-particle diffusion models. We conclude that this environmentally friendly nanocomposite has good potential for use in wastewater treatment and related purposes.

Modification of Enteromorpha prolifera with dielectric barrier discharge plasma to enhance malachite green adsorption

Dyes, a kind of visible chemical, have severe deleterious effects on human health and ecological environment. In this work, batch biosorption experiments were carried out under various experimental conditions such as pH value and agitation time to optimize the potentiality of Enteromorpha prolifera for the removal of malachite green (MG) dye from aqueous solution (70·7%). Then, the algal biomass was treated with a dielectric barrier discharge (DBD) in helium for 4 and 10 min to enhance MG removal efficiency (84·7 and 96·6%). In addition, Fourier-transform infrared spectroscopy in combination with scanning electron microscopy was employed to monitor the chemical and physical changes of algal cells treated by DBD. This study illustrates that DBD may serve as an effective tool to activate the functional groups on the cell wall surface for dye binding, and it even offers an alternative new technique to improve the adsorption properties of native biosorbents for the removal of toxic dyes from wastewater.

Adsorption of Cationic Dyes on a Magnetic 3D Spongin Scaffold with Nano-Sized Fe3O4 Cores

The renewable, proteinaceous, marine biopolymer spongin is yet the focus of modern research. The preparation of a magnetic three-dimensional (3D) spongin scaffold with nano-sized Fe3O4 cores is reported here for the first time. The formation of this magnetic spongin-Fe3O4 composite was characterized by X-ray diffraction (XRD), thermogravimetric analysis (TGA), differential thermal analysis (DTA) (TGA-DTA), vibrating sample magnetometer (VSM), Fourier-transform infrared spectroscopy (FTIR), and zeta potential analyses. Field emission scanning electron microscopy (FE-SEM) confirmed the formation of well-dispersed spherical nanoparticles tightly bound to the spongin scaffold. The magnetic spongin-Fe3O4 composite showed significant removal efficiency for two cationic dyes (i.e., crystal violet (CV) and methylene blue (MB)). Adsorption experiments revealed that the prepared material is a fast, high-capacity (77 mg/g), yet selective adsorbent for MB. This behavior was attributed to the creation of strong electrostatic interactions between the spongin-Fe3O4 and MB or CV, which was reflected by adsorption mechanism evaluations. The adsorption of MB and CV was found to be a function of pH, with maximum removal performance being observed over a wide pH range (pH = 5.5-11). In this work, we combined Fe3O4 nanoparticles and spongin scaffold properties into one unique composite, named magnetic spongin scaffold, in our attempt to create a sustainable absorbent for organic wastewater treatment. The appropriative mechanism of adsorption of the cationic dyes on a magnetic 3D spongin scaffold is proposed. Removal of organic dyes and other contaminants is essential to ensure healthy water and prevent various diseases. On the other hand, in many cases, dyes are used as models to demonstrate the adsorption properties of nanostructures. Due to the good absorption properties of magnetic spongin, it can be proposed as a green and uncomplicated adsorbent for the removal of different organic contaminants and, furthermore, as a carrier in drug delivery applications.

Adsorptional-photocatalytic removal of fast sulphon black dye by using chitin-cl-poly(itaconic acid-co-acrylamide)/zirconium tungstate nanocomposite hydrogel

In the present work, the removal of fast sulphon black (FSB) dye from water was executed by using chitin-cl-poly(itaconic acid-co-acrylamide)/zirconium tungstate nanocomposite hydrogel (Ch-cl-poly(IA-co-AAm)-ZrW NCH). The Ch-cl-poly(IA-co-AAm)-ZrW NCH was fabricated proficiently by microwave-induced sol-gel/copolymrization method. The zirconium tungstate (ZrW) photocatalyst was prepared by co-precipitation method using sodium tungstate and zirconium oxychloride in ratio (2:1). The polymeric hydrogel part has been used to support the ZrW, and it acted as an adsorbent for adsorptive removal of FSB dye. The band gap for nanocomposite hydrogel was found about 4.18 eV by using Tauc equation. The Ch-cl-poly(IA-co-AAm)-ZrW NCH was characterized by various techniques as FTIR (Fourier-transform infrared spectroscopy), X-ray diffraction (XRD), transmittance electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS) and scanning electron microscopy (SEM). The adsorptional-photocatalytic remediation experiment of FSB dye was optimized for reaction parameters as FSB dye and Ch-cl-poly(IA-co-AAm)-ZrW NCH concentration, and pH. The maximum percentage removal for FSB dye was observed at 92.66% in 120 min under adsorptional-photocatalysis condition.

Construction of hydrogels based on the homogeneous carboxymethylated chitin from Hericium erinaceus residue: Role of carboxymethylation degree

Carboxymethyl chitin hydrogels with different degree of substitution (DS) were prepared by the homogeneous carboxymethylation of chitin extracted from Hericium erinaceus residue. The effect of DS on gel structure and property were studied. Results showed that the DS of carboxymethyl chitin hydrogels can be increased by increasing the amount of sodium chloroacetate. The equilibrium swelling degree and pH swelling sensitivity of the hydrogels were enhanced as the increase of DS. Zeta potential, low-field nuclear magnetic resonance, contact angle and molecular dynamics simulation results suggested that the introduction of carboxymethyl functional group enhanced the negative charge, water mobility, surface hydrophilicity and the ability to form hydrogen bonds with water of the hydrogels, resulting in an increased swelling degree of the hydrogels. Moreover, the prepared hydrogels showed different adsorption capability to various dyes, and the adsorption performance of the prepared hydrogels for cationic dyes could be enhanced as the increase of DS.

Water stable graphene oxide metal-organic frameworks composite (ZIF-67@GO) for efficient removal of malachite green from water

Malachite green (MG) is extensively applied in aquaculture worldwide as a therapeutic agent. MG and its primary metabolite leucomalachite green (LMG) are commonly detected in aquaculture products. MG can cause serious health concerns (in vivo carcinogenic/genotoxic). The extensive water solubility of MG leads to water pollution and hence it is mandatory to remove MG from water. The current study explores adsorptive removal of MG from water using highly water stable Zeolitic Imidazolate framework/graphene oxide composites (ZIF-67@GO). Adsorption performance of newly synthesized composites is justified for MG removal with excellent results of pseudo second order (R² = 0.99955) which is well-fitted in this case. ZIF-67@GO data of adsorption isotherm for MG is observed using Freundlich Model (R² = 0.99999) and with adsorption capacity value observed (134.79 mg/g) with removal efficiency of 99.18%, indicates π-staking and electrostatic association between ZIF-67@GO and MG molecules. Synthesized material has retained reusability while removal efficiency reduced only by 6% after many cycles. Furthermore, factors effecting absorption like contact time, pH, adsorbent dose and quantity and temperature are also determined.

Removal of Disperse Blue 56 from synthetic textile effluent using ionic flocculation

The textile industry is one of the main generators of industrial effluent due to the large volumes of water containing a wide variety of pollutants, including dyes. Thus, the present study aimed to remove the Disperse Blue 56 dye present in synthetic textile effluent using ionic flocculation through surfactant flocs produced from animal/vegetable fat, assessing the system at different surfactant concentrations and temperatures. The process kinetics, adsorption mechanism and equilibrium were evaluated. The results show that the kinetics was better described by the Elovich model when compared to pseudo-first order and pseudo-second order models, indicating that chemical adsorption occurs during the process. The study of the adsorption mechanism obtained lower outer layer diffusivities than their intra-particle counterparts, demonstrating that the dye transport to the surfactant floc is controlled through the outer layer. The Langmuir isotherm was suitable for equilibrium data and the separation factor calculated showed that the isotherm is classified as favorable. Dye removal efficiency reached 87% after 360 minutes of contact between the effluent and the surfactant flocs, indicating that ionic flocculation is an efficient alternative in the treatment of textile effluent containing disperse dye.

Hollow cellulose-carbon nanotubes composite beads with aligned porous structure for fast methylene blue adsorption

Polysaccharide based beads with unique porous structure have gained considerable interests due to their specific adsorption behaviors and biodegradability. The purpose of this paper was to develop hollow cellulose/carbon nanotubes composite beads with aligned porous structure which have potential applications in fast adsorption field. The composite beads were fabricated by ice template and freeze-drying technology. Different characterizations have proved that the carbon nanotubes and magnetic nanoparticles have been incorporated into the cellulose beads. Higher concentration of carbon nanotubes and cellulose would result in a larger diameter of the composite beads. The composite beads can effectively adsorb the methylene blue (MB). The pseudo-second-order model and Langmuir isotherm were best fitted to the adsorption. The composite beads showed a fast adsorption behavior towards MB with a t_1/2 of 1.07 min obtained from pseudo-second-order model. The maximum adsorption capacity was 285.71 mg g^-1 at pH 7.0. The composite beads also showed good reusability and biodegradability. We anticipate that different polysaccharides based composite beads with aligned porous structure can be obtained through the similar methods and applied in adsorption fields.

Mg-Al/Biochar Composite with Stable Structure for Malachite Green Adsorption from Aqueous Solutions

Mg-Al-layered double hydroxide (LDH) was fabricated using a coprecipitation method at pH 10. Thereafter, Mg-Al-LDH was impregnated with biochar to manufacture a Mg-Al/Biochar composite. The composite was characterized using powder X-ray diffraction (XRD), Fourier-transform infrared (FTIR) spectroscopy, N2 adsorption—desorption, thermogravimetry-differential thermal analysis (TG-DTA), and scanning electron microscopy (SEM) experiments, and was subsequently used for malachite green (MG) adsorption. MG adsorption experiments were performed in a batch system, and the effects of temperature and adsorption kinetic and isotherm parameters on the adsorption process were analyzed. The stability of Mg-Al/Biochar was evaluated using regeneration experiments over three cycles. The peaks at 11.47° (003), 22.86° (002), 34.69° (012), and 61.62° (116), in the XRD profile of Mg-Al/Biochar suggested that Mg-Al/Biochar was successfully fabricated. The surface area of Mg-Al/Biochar was up to five times larger than that of pristine Mg-Al-LDH. The adsorption of MG on Mg-Al/Biochar was dominated by interactions at the surface of the adsorbent and was classified as physical adsorption; moreover the maximum adsorption capacity ofMg-Al/Biochar was 70.922 mg/g. Furthermore, the MG removal of Mg-Al/Biochar during three successive adsorption cycles (i.e. 66.73%, 65.57%, and 65.77% for the first, second, and third adsorption cycle) did not change significantly, which indicated the stable structure of the adsorbent. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

Kinetic and Isotherm Studies of Ni2+ and Pb2+ Adsorption from Synthetic Wastewater Using Eucalyptus camdulensis—Derived Biochar

The production of biosorbents by waste biomass has attracted considerable attention due to the low cost and abundance of the raw materials. Here biochar produced from Eucalyptus camdulensis sawdust (EU-biochar) via pyrolysis at 600 °C was used as a potential biosorbent for Ni2+ and Pb2+ metal ions from wastewater. Characterization experiments indicated the formation of C- and O-bearing functional groups on the EU-biochar surface, while shifts and changes in the shape of C–H bands suggested the adsorption of Ni2+ and Pb2+ onto EU-biochar by interacting with surface carboxylic groups. Pb2+ was adsorbed more quickly than Ni2+, indicating a faster and stronger interaction of Pb2+ with EU-biochar compared to Ni2+. As the initial concentrations of both metal ions increased, the percentage removal decreased, whereas increasing the EU-biochar dose improved the percentage removal but impaired the adsorption capacity for Ni2+ and Pb2+. The adsorption capacity could only be improved without affecting the percentage removal of both ions by increasing the pH of the metal solutions. The sorption efficiency of EU-biochar and the removal mechanism of Ni2+ and Pb2+ were further explored using non-linear and linear forms of kinetic and isotherm models.

Successful Application of Eucalyptus Camdulensis Biochar in the Batch Adsorption of Crystal Violet and Methylene Blue Dyes from Aqueous Solution

Eucalyptus camdulensis biochar (Ec-bio) was used to adsorb crystal violet (CV) and methylene blue (MB) dyes, which was optimized and further evaluated using different isotherm and kinetic models. Microscopy and spectroscopy techniques showed the interactions of the dyes with the surface functional groups of the Ec-bio, resulting in the removal of the dyes from aqueous solution. Both dyes were immediately uptaken, with equilibrium reached in 60 min, with a higher sorption efficiency of CV compared to MB. Thermodynamic parameters showed endothermic adsorption and the nonspontaneous adsorption of both dyes onto the Ec-bio. Both the adsorption capacity and percentage removal increased with the increasing solution pH from 2.0 to 4.0 and to 10 for CV and MB. An increase in adsorption capacity was observed upon increasing the initial concentrations, with a corresponding decrease in the percentage removal. The pseudo-second-order (PSO) and Elovich kinetic models (nonlinear approach) were a good fit to the data of both dyes, confirming a chemisorptive adsorption process. The Langmuir isotherm fitted well to the CV data, supporting its monolayer adsorption onto the Ec-bio, while the Freundlich isotherm was a good fit to the MB dye data, suggesting the surface heterogeneity of the Ec-bio. The Dubinin–Radushkevich isotherm was a good fit to the adsorption CV data compared with the MB dye, suggesting the physisorption of both dyes onto the Ec-bio due to its mean free energy of adsorption of <8 kJ mol−1.

Adsorption and Desorption Properties of Polyethylenimine/Polyvinyl Chloride Cross-Linked Fiber for the Treatment of Azo Dye Reactive Yellow 2

In this study, the optimal conditions for the fabrication of polyethylenimine/polyvinyl chloride cross-linked fiber (PEI/PVC-CF) were determined by comparing the adsorption capacity of synthesized PEI/PVC-CFs for Reactive Yellow 2 (RY2). The PEI/PVC-CF prepared through the optimal conditions was characterized using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and Brunauer–Emmett–Teller (BET) analyses. Several batch adsorption and desorption experiments were carried out to evaluate the sorption performance and reusability of PEI/PVC-CF for RY2. As a result, the adsorption of RY2 by PEI/PVC-CF was most effective at pH 2.0. A pseudo-second-order model fit better with the kinetics adsorption data. The adsorption isotherm process was described well by the Langmuir model, and the maximum dye uptake was predicted to be 820.6 mg/g at pH 2.0 and 25 °C. Thermodynamic analysis showed that the adsorption process was spontaneous and endothermic. In addition, 1.0 M NaHCO₃ was an efficient eluent for the regeneration of RY2-loaded PEI/PVC-CF. Finally, the repeated adsorption–desorption experiments showed that the PEI/PVC-CF remained at high adsorption and desorption efficiencies for RY2, even in 17 cycles.

Comparative Removal of Lead and Nickel Ions onto Nanofibrous Sheet of Activated Polyacrylonitrile in Batch Adsorption and Application of Conventional Kinetic and Isotherm Models

We investigated the adsorption of lead (Pb²⁺) and nickel (Ni²⁺) ions by electrospun membranes of polyacrylonitrile (PAN) nanofiber activated with NaHCO₃ (PANmod). Analysis by Fourier-transform infrared spectrometry (FTIR), field emission scanning electron microscopy (FE-SEM), and energy dispersive X-ray spectroscopy (EDX) validated the functionalization of PAN nanofibers with NaHCO₃, and the successful agglomeration of Pb²⁺ and Ni²⁺ onto PANmod. After a rapid uptake of the heavy metal ions (15 min), the equilibrium contact time was attained (60 min) following a linear increase of both adsorption capacity and removal efficiency. PANmod showed a better affinity for Ni²⁺ than Pb²⁺. The adsorption on PANmod was best described by the pseudo-second-order kinetic model for both studied models, supporting chemisorption. By varying the solution pH from 2.0 to 9.0, we found that the adsorption capacity followed an increasing trend, reaching a maximum at the pH of 7.0. Despite increasing adsorption capacities, the removal efficiency of both heavy metal ions exhibited a decreasing trend with increase in initial concentrations. The amount of PANmod directly affects the removal efficiency, with 0.7 and 0.2 g being the optimum dose for maximum uptake of Pb²⁺ and Ni²⁺, respectively. The Langmuir model fitted well the Pb²⁺ adsorption data suggesting monolayer adsorption, and the Freundlich model perfectly fitted the Ni²⁺ adsorption data, indicating heterogeneous adsorption. The estimated values of the mean free energy of adsorption in the D–R isotherm indicated a physical adsorption of both heavy metal ions into the surface of the PANmod.

Graphene oxide decorated with cellulose and copper nanoparticle as an efficient adsorbent for the removal of malachite green

In this study, the graphene oxide surface was modified by grafting of nanocellulose and copper nanoparticles to promote the surface charge and adsorption efficiency for malachite green (MG). The structural and configurational properties of GO-CEL-Cu were verified by UV/Vis, SEM, TEM, EDX and FTIR spectroscopy and confirmed the electrostatic interaction and hydrogen bonding between GO, CEL and Cu-NPs. TEM images confirmed the deposition of Cu-NPs size between 24 and 37 nm on the GO surface. The uniform fine particles size makes strong interfacial interaction with GO sheets result in efficient load transfer from the matrix to the hybrid. The variable parameters such as adsorbent amount, MG concentration, pH, time and temperature were investigated to achieve optimum experimental condition. The experimental data was justified by Langmuir isotherm model with adsorption capacity for GO, GO-Cu, GO-CEL, GO-CEL-Cu as 127.3, 149.2, 156.8 and 207.1 mg/g, respectively. The spontaneity and endothermic nature of the process were confirmed by negative Gibbs free energy and followed the pseudo-second-order rate equation. Additionally, positive values of enthalpy and entropy suggesting endothermic process and increase randomness during process, respectively. In conclusion, nanocomposite is capable to adsorb the toxic dye due to its well economic, eco-friendly, well adsorption rate and regeneration ability.

Assessment of cancer risk of microplastics enriched with polycyclic aromatic hydrocarbons

Abundance of microplastics in aquatic and marine ecosystems is contaminating the seafood and it is leading to transfer of toxic pollutants to human beings. In this article, we report the hazardous nature and cancer risk of microplastics which originate from e-waste. Capture of carcinogenic polycyclic aromatic hydrocarbons (PAHs) onto microplastics by adsorption phenomena and an assessment of probable cancer risk of ingested PAHs enriched microplastics by human beings have been investigated. The adsorption equilibrium was well fit for the Freundlich isotherm model. The adsorption capacity of carcinogenic PAHs on microplastics was ranged from 46 to 236 μg g^-1 and the maximum binding was achieved within 45 min in water. The leachate derived from microplastics of e-waste were highly hazardous in nature, for example, the sum of PAHs was 3.17 mg L^-1 which is about 1000 times higher than the standard for benzo[a]pyrene, a congener of PAHs. The calculated cancer risk in terms of lifetime of microplastic ingestion would be 1.13 × 10^-5 for children and 1.28 × 10^-5 for adults and these values are higher than the recommended value of 10⁶. The abundance of microplastics could transfer hazardous pollutants to seafood (e.g., fishes and prawns) leading to cancer risk in human beings.

Carbon dot cross-linked polyvinylpyrrolidone hybrid hydrogel for simultaneous dye adsorption, photodegradation and bacterial elimination from waste water

The creation of a polymeric hydrogel from polyvinylpyrrolidone (PVP) cross-linked by Carbon Quantum Dots (CD) for the adsorption and photocatalytic degradation of both cationic and anionic dyes. PVP, an important biocompatible constituent and often surplus in cosmetic industry, was carboxylated through NaOH refluxing and covalently conjugated to surface amine functionality of CD derived from lemon juice and Cysteamine. The hybrid hydrogel was obtained from PVP-CD covalent conjugate by careful manipulation of pH and found to possess better rheological properties than only carboxylate-PVP. The monolayer physisorption of the dyes on the hydrogel was affected by hydrogen bonding, dispersion or inductive effect, and π-π interaction with the polymer backbone as well as the CD that followed pseudo-second-order kinetics. Degradation of the adsorbed dyes was instated by the unique Reactive Oxygen Species (ROS) generating ability of the CD embedded in the hydrogel matrix upon exposure to sunlight, the mechanism of which is also unveiled. The same CD-induced ROS was found to effectively annihilate both gram-positive and gram-negative bacteria in real polluted water in less than 10 min of photoexcitation of the hydrogel. The hydrogel was restored by mild acid wash that is able to perform dye adsorption and photo-degradation upto four cycles.