A new integrated approach for dye removal from wastewater by polyoxometalates functionalized membranes

Surface modification of nanofiltration membrane using polyoxometalates for improved separation and antifouling performance

In this study, polyoxometalates (POMs) as a core-modifying material was used to fabricate the nanofiltration (NF) membrane on the polyvinylidene fluoride (PVDF) microfiltration membrane substrate via a novel interfacial polymerization (IP) method. The formation mechanism of the POMs-modified composite membrane was proposed. The separation and antifouling properties were further investigated. After cross-linking with POMs through the new IP reaction, the modified composite membrane showed improved hydrophilicity, water flux, and salt rejection. In the humic acid fouling experiment, the POMs-modified membrane exhibited the best antifouling performance, with a flux recovery rate of up to 91.3%. Electrochemical impedance spectroscopy was further used to investigate the antifouling performance of the membranes. Nyquist and Bode plots of the POMs-modified membranes showed no significant change before and after fouling compared to the PVDF membrane substrate, indicating reduced fouling attachment on the modified membrane, which was consistent with the fouling index and flux variation observed during the fouling experiment. Our findings provide a simple and valuable route for fabricating POMs-functionalized NF membranes with desirable separation and antifouling performance.

Removal of Methylene Blue from Aqueous Solutions by Surface Modified Talc

In this study, raw talc powder surface modification was conducted, and the powder was modified in two different methods using acid washing and ball milling. Modified talc was characterized by X-ray diffraction (XRD), Fourier transforms infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). In order to investigate the adsorption capacity of modified talc on dyes, adsorption experiments were carried out with methylene blue (MB) in aqueous solutions as the target contaminant. The findings of the characterization revealed that both modifications increased the adsorption capacity of talc, which was attributed to changes in specific surface area and active groups. The influence of process parameters such as contact time, pH, dye concentration, and adsorbent dosage on the adsorption performance was systematically investigated. Modified talc was able to adsorb MB rapidly, reaching equilibrium within 60 min. Additionally, the adsorption performance was improved as the pH of the dye solution increased. The isotherms for MB adsorption by modified talc fitted well with the Langmuir model. The pseudo-second-order model in the adsorption kinetic model properly described the adsorption behavior. The results show that the modified talc can be used as an inexpensive and abundant candidate material for the adsorption of dyes in industrial wastewater.

Adsorption of different anionic and cationic dyes by hybrid nanocomposites of carbon nanotube and graphene materials over UiO-66

Amongst many chemical pollutants that cause environmental pollution, the presence of organic dyes in water resources can cause substantial health issues. Thus, owing to their mutagenicity and their adverse effects on human health, environment, and animals, they must be removed from industrial wastewater. In this study, UiO-66 metal-organic framework, as well as composite nanoparticles with carbonaceous materials such as MWCNTs-COOH and graphene oxide (GO) with different molar ratios (2.9 and 5.8 wt.%), were synthesized through solvothermal method since carbonaceous materials are an emerging material that demonstrates improvement in the properties of adsorbents. Then, the synthesized materials were utilized as a solid adsorbent for removing four different dyes including; anionic methyl red (MR), anionic methyl orange (MO), cationic methylene blue (MB), and cationic malachite green (MG) prepared from distilled water. The properties of prepared adsorbents were characterized via X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), Photoluminescence spectroscopy (PL), Brunauer-Emmett-Teller (BET), as well as surface area analyzer and energy dispersive spectroscopy (EDS-MAP). Further, the influences of various factors including initial concentrations of the dyes and adsorption process time on adsorption of dyes were investigated. Adsorption experiments indicated that synthesized adsorbents exhibited the highest adsorption efficiency towards MR and MO dyes. Moreover, the experimental adsorption results revealed that MWCNTs-UiO-66 nanocomposites could adsorb 98% of MR and MO as well as 72% of MB and 46% of MG. Furthermore, the kinetic and stability of the materials over time were investigated. To reach a clear picture, adsorption experiments demonstrated that the amount of dye uptake on adsorbents was enhanced by increasing the contact time as well as uptake of materials with time were stable for both cationic and anionic dyes. The MR, MO, and MB adsorption isotherms were fitted with the Langmuir and Freundlich models. The Langmuir showed the highest agreement in these dyes and MWCNTs-UiO-66 (2.9 and 5.8 wt.%) exhibited a maximum adsorption capacity of 105.26 mg/g for MR, while the MG isotherm was in line with the Langmuir model.

Eco-friendly approach for efficient catalytic degradation of organic dyes through peroxymonosulfate activated with pistachio shell-derived biochar and activated carbon

This study introduces a simple method for the preparation of biochar (BCP) and activated carbon using pistachio (ACP) external hull as residual solid waste. Low-cost raw materials, biodegradable, recyclable and organic solid wastes are advantages of this method. Furthermore, complete degradation of methyl orange (MO) and methylene blue (MB) to H₂O and CO₂ as eco-friendly compounds in mild reaction condition occurs at a short time. Also, the effects of crucial parameters (temperature, time, catalyst dosage, initial dye and oxidant concentration, initial reaction pH level and radical scavengers), capability, adaptability, performance and reusability of ACP were also evaluated. The results displayed that dyes could be decomposed effectively by the PMS/ACP-800 system. Furthermore, the sulphate radical (SO4∙-) was a major active role in the degradation process, while hydroxyl radical (^•OH) played a minor role. Overall, ACP had yielded high degradation of MB and MO dyes; therefore, ACP-800 could be effectively and reliably applied in the treatment of industry effluents containing MB and MO dyes.

A Nickel-Containing Polyoxomolybdate as an Efficient Antibacterial Agent for Water Treatment

In view of the water pollution issues caused by pathogenic microorganisms and harmful organic contaminants, nontoxic, environmentally friendly, and efficient antimicrobial agents are urgently required. Herein, a nickel-based Keggin polyoxomolybdate [Ni(L)(HL)]₂H[PMo₁₂O₄₀] 4H₂O (1, HL = 2-acetylpyrazine thiosemicarbazone) was prepared via a facile hydrothermal method and successfully characterized. Compound 1 exhibited high stability in a wide range of pH values from 4 to 10. 1 demonstrated significant antibacterial activity, with minimum inhibitory concentration (MIC) values in the range of 0.0019–0.2400 µg/mL against four types of bacteria, including Staphylococcus aureus (S. aureus), Bacillus subtilis (B. subtilis), Escherichia coli (E. coli), and Agrobacterium tumefaciens (A. tumefaciens). Further time-kill studies indicated that 1 killed almost all (99.9%) of E. coli and S. aureus. Meanwhile, the possible antibacterial mechanism was explored, and the results indicate that the antibacterial properties of 1 originate from the synergistic effect between [Ni(L)(HL)]⁺ and [PMo₁₂O₄₀]³⁻. In addition, 1 presented effective adsorption of basic fuchsin (BF) dyes. The kinetic data fitted a pseudo-second-order kinetic model well, and the maximum adsorption efficiency for the BF dyes (29.81 mg/g) was determined by the data fit of the Freundlich isotherm model. The results show that BF adsorption was dominated by both chemical adsorption and multilayer adsorption. This work provides evidence that 1 has potential to effectively remove dyes and pathogenic bacteria from wastewater.

Fe3O4-doped silk fibroin-polyacrylamide hydrogel for selective and highly efficient absorption of cationic dyes pollution in water

Overuse of organic dyes has caused serious threats to the ecosystem and human health. However, the development of high-efficient, environmentally friendly, selective, and degradable cationic dye adsorbents remains a huge challenge. In this work, a novel Fe₃O₄nanoparticles doped silk fibroin-polyacrylamide magnetic hybrid hydrogel (Fe₃O₄@SF-PAAM) was successfully fabricated by combining free radical polymerization to prepare hydrogels andin situco-precipitation to prepare nanoparticles. The obtained Fe₃O₄@SF-PAAM hydrogel shows strong magnetic performance with saturated magnetic of 10.2 emu mg^-1and excellent swelling properties with a swelling ratio of 55867%. In addition, Fe₃O₄@SF-PAAM can adsorb cationic dyes such as methylene blue (MB), crystal violet, and Rhodamine B, but has no adsorption effect on anionic dyes such as methyl orange, congo red, and carmine, indicating that Fe₃O₄@SF-PAAM has good selective adsorption properties for cationic dyes. Interestingly, the adsorption capacity of Fe₃O₄@SF-PAAM was approached 2025 mg g^-1for MB (MB, a typical cation dye) at 25 °C and neutral. Meanwhile, the hybrid hydrogel is reusable, the removal rate for MB is still over 90% after the five adsorption-desorption cycles. The fabricated magnetic hybrid hydrogel is a kind of a highly-efficiency and eco-friendly adsorbent and presents great potential applications in water purification and environmental protection.

Simultaneous adsorption for cationic and anionic dyes using chitosan/electrospun sodium alginate nanofiber composite sponges

The coexistence of anionic and cationic dyes in dye wastewater has highlighted a great necessity to develop amphoteric adsorbents for their simultaneous removal. Herein, an amphoteric composite sponge was successfully fabricated by combining chitosan with electrospun sodium alginate nanofiber using lyophilization in acetic acid/water/dioxane mixed solvents, which owned the abundant functional groups and superior microstructure of interconnected pores and nanoscale fibers, beneficial for the adsorption capacity improvement. The optimum adsorption capacities for Acid Blue-113 and Rhodamine B were 926.2 ± 25.7 mg/g and 695.4 ± 17.0 mg/g, respectively, much higher than that of the controlled sample prepared with chitosan and non-spinning sodium alginate in traditional acetic acid/water solvents. Meanwhile, the sponge provided with the superior adsorption performance under various pH environment and cyclic adsorption. Importantly, it had considerable simultaneous adsorption capacity for binary system containing anionic and cationic dyes. Overall, the chitosan/electrospun sodium alginate nanofiber composite sponge shows potential for complex wastewater treatment.

Efficient Removal of Dye from Wastewater without Selectivity Using Activated Carbon-Juncus effusus Porous Fibril Composites

Adsorption techniques have been successfully applied in water purification because of their flexibility, simplicity of design, and effectiveness. Activated carbon is an effective absorbent using for dye adsorption; however, the powder structure is not conducive for practical applications and cannot be used to filter dye solutions which are challenges that still need to be addressed. Herein, a natural cellulose-based absorbent, activated carbon-Juncus effusus fiber (AC-JE fiber), demonstrates the removal of all kinds of dyes without selectivity and humic substances and humic-like organics from wastewater. The combined macroporous structures of JE fibers and the microporous and mesoporous structures of activated carbon particles enhance their adsorption properties. These composite absorbents have excellent adsorption and continuous filtration effect. The rejection rate is approximately 100% not only on acidic and anionic dyes but also on basic and cationic dyes. Moreover, the dye solution adsorbed by AC-JE fibers exhibits an ideal freshwater quality (almost no bacteria), similar to that of the deionized water. The AC-JE fibers prove their potential for dye removal, in both adsorption and filtration. Their sterilization ability substantiates their potential in the field of water purification as they can be used as ideal absorbents based on cellulose for removing dyes and purifying wastewater.

Constructing chiral polyoxometalate assemblies via supramolecular approaches

Polyoxometalates (POMs), as a typical class of discrete metal oxide clusters that are known in inorganic and structural chemistry since long, have displayed more and more interesting applications over recent years. However, in comparison to the chemical synthesis, the photochemical, electrochemical, and magnetic properties, the structural asymmetry, and relative characteristic investigations arising therefrom are far behind even if they are very important for functional materials, especially in solution systems. One of the main reasons is that it is hard to control and maintain a stable chiral state of POMs to carry out further corresponding performances. Aiming to overcome these disadvantages, the main concerns of this review are to discuss the generation of the chirality for discrete metal oxide clusters, chirality transfer via a supramolecular approach, chirality amplification in self-assemblies, and the related functional properties such as photochromism, catalysis, and bioactivities in solutions. Considering that some previous reviews dealt with chiral structures and packing architectures in the crystalline solids of POMs, this article only concentrates on the induced chirality and material properties in solution systems, which have been more active recently but no review article has been involved in this interesting area.

Grafting of Acrylic Membrane Prepared from Fibers Waste for Dyes Removal: Methylene Blue and Congo Red

Dyes are a type of pollutant that have been discharged into water streams by various industries and had harmful effects on the environment and human health. Therefore, present work was directed to recycle acrylic fibers waste to be used as an adsorbent to exclude dyes such as methylene blue (MB) and Congo red (CR) from dyes-polluted wastewater. Acrylic fibers waste was converted into membrane followed by chemical grafting with p-phenylenediamine monomer to form functional modified membranes. Afterwards, some characterization analyses; Fourier transform-infrared, scanning electron microscope, swelling behavior, and porosity properties were performed for the acrylic fiber grafted membrane (AFGM). For obtaining the best conditions that permit the highest adsorption capacity of the AFGM, some preliminary experiments followed by general full factorial design experiments were displayed. Langmuir, Freundlich isotherms and kinetic studies evaluations were applied. Results revealed that, the adsorption capacities of the AFGM were 61% for Methylene blue and 86% for Congo red that stated the high affinity of the AFGM to the anionic dyes. The reusability of the AFGM membranes in different cycles for 3Rs processes “Removal, Recovery, and Re-use” indicated the efficiency of the AFGM to be used in wastewater treatment.

A Study on the Reaction Kinetics of Anaerobic Microbes Using Batch Anaerobic Sludge Technique for Beverage Industrial Wastewater

In this study, a low-cost, efficient, and environmentally friendly anaerobic sludge process for the treatment of industrial beverage wastewater was investigated to analyze the effect of bacteria growth on the degradation of organic matter (chemical oxygen demand). Additionally, the mechanism, interactions between the microbe’s growth, and operating conditions of an anaerobic batch reactor along with the wastewater treatment efficiency were evaluated via microbial kinetics. The kinetic coefficients based on chemical oxygen demand (COD) by conventional techniques such as kinetic coefficients growth yield (0.46 mg VSS/mg COD), saturation coefficient (3500 mg/L COD), the maximum rate of substrate utilization per unit mass of biomass (0.0066 mg/L COD), growth rate by Monod equation, M (0.03833 L/h), and maximum growth rate, μm (0.03672 L/h) were calculated. The results show a higher rate of substrate degradation (0.54 day−1) due to the high COD removal efficiency (CRE) of 99.31% during 13 days that was achieved, which can be attributed to the active involvement of anaerobic microbes in the process of degradation. Based on these results, it can be concluded that the current study can be used as an effective way to analyze the industrial beverage wastewater at commercial levels.

ZnO-ZnTe hierarchical superstructures as solar-light-activated photocatalysts for azo dye removal

The excessive amount of textile effluents disposed into the water streams is a common source of contamination of the hydrosphere. To efficiently remove pollutants in water bodies, there is growing demand for highly efficient, cost effective, and green remediation techniques. In line with such demand, a heterostructured photocatalyst (ZnO-ZnTe) has been prepared through the assembly of zinc oxide (ZnO) and zinc telluride (ZnTe). A synergistic interaction between surface adsorption and photocatalysis was explored for the removal of azo dye using a hierarchical superstructure under solar-light irradiation. Methylene blue (MB) was bleached by about 91% under visible irradiation for 2 h to support the role of the prepared heterostructures as effective photocatalysts (QY is 3.16 × 10^-7 molecules/photon). Moreover, the kinetic reaction rate of ZnO-ZnTe superstructures was 19.0 μmol g^-1 h^-1, which was 1.54 and 1.97 times higher than those of pristine ZnO and ZnTe, respectively. These results may be ascribed to the presence of a common cation that may have helped in the diffusion of photogenerated electrons between ZnO and ZnTe, while efficiently suppressing the recombination frequency of photogenerated electrons and holes.

Adsorption of Methylene Blue Dye by Calix[6]Arene-Modified Lead Sulphide (Pbs): Optimisation Using Response Surface Methodology

Lead sulphide (PbS) modified with calix[6]arene was synthesised as an alternative and regenerative adsorbent for the adsorption of methylene blue (MB) dye. The prepared calix[6]arene-modified PbS was characterised via Fourier-transform infrared spectroscopy, field emission scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The response surface methodology (RSM) based on the central composite design (CCD) was employed to identify the most significant factors, such as the initial concentration, adsorbent dosage, pH, and temperature, and to optimise the effects of the factors on the adsorptive efficiency as its response. The optimised initial concentration, adsorbent dosage, pH, and temperature were 20.00 mg/L initial concentration, 44.00 mg calix[6]arene-modified PbS, pH 6, and a temperature of 31.00 °C. A good correlation between the values and well-fitted model was observed. The adsorption performance was evaluated based on the percentage removal of MB dye from the water system. The adsorption isotherm best fit the Langmuir isotherm model, and the adsorption rate was followed by a pseudo-second-order kinetic model, a single layer chemical adsorption with a maximum adsorption capacity (q_max) of 5.495 mg/g.

An organic-inorganic hybrid nanomaterial composed of a Dowson-type (NH4)6P2Mo18O62 heteropolyanion and a metal-organic framework: synthesis, characterization, and application as an effective adsorbent for the removal of organic dyes

In this work, an inorganic-organic hybrid nanomaterial, P2Mo18/MIL-101(Cr), based on Wells-Dawson-type (NH4)6P2Mo18O62 polyoxometalate (abbreviated as P2Mo18) and the MIL-101(Cr) metal-organic framework was fabricated by the reaction of (NH4)6P2Mo18O62, Cr(NO3)3·9H2O and terephthalic acid under hydrothermal conditions. The as-prepared recyclable nanohybrid was fully characterized using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR) equipped with energy dispersive X-ray microanalysis (EDX), field emission scanning electron microscopy (FE-SEM), Raman spectroscopy and Brunauer-Emmett-Teller (BET) specific surface area studies. All the analyses confirmed the successful insertion of P2Mo18O62 6- heteropolyanion within the cavities of MIL-101(Cr). The encapsulated MIL-101(Cr) showed a considerable decrease in both pore volume and surface area compared with MIL-101(Cr) due to incorporation of the very large Dowson-type polyoxometalate into the three-dimensional porous MIL-101(Cr). The nanohybrid had a specific surface area of 800.42 m2 g-1. The adsorption efficiency of this nanohybrid for removal of methylene blue (MB), rhodamine B (RhB), and methyl orange (MO) from aqueous solutions was evaluated. Surprisingly, the composite not only presented a high adsorption capacity of 312.5 mg g-1 for MB, but also has the ability to rapidly remove 100% MB from a dye solution of 50 mg L-1 within 3 min. These results confirmed that this adsorbent is applicable in a wide pH range of 2-10. The nanohybrid showed rapid and selective adsorption for cationic MB and RhB dyes from MB/MO, MB/RhB, MO/RhB and MB/MO/RhB mixed dye solutions. The equilibrium adsorption data were better fitted by the Langmuir isotherm. Kinetics data indicate that the adsorption of the dye follows a pseudo-second order kinetics model. Also, this material could be effortlessly separated and recycled without any structural modification. Accordingly, it is an efficient adsorbent for removing cationic dyes.

Preparation and characterization of novel polyoxometalate/CoFe2O4/metal-organic framework magnetic core-shell nanocomposites for the rapid removal of organic dyes from water

In this study, the MIL-101(Cr) metal–organic framework was functionalized with a Dowson-type polyoxometalate (P₂W₁₈O₆₂⁶⁻; POM) and magnetic spinel cobalt ferrite (CoFe₂O₄; CFO) through a hydrothermal route and was characterized by means of FT-IR, XRD, FE-SEM, EDX, BET, and VSM measurements. All analyses confirmed the successful encapsulation of POM (∼32.2 wt%) into the magnetic MIL-101(Cr) framework. Compared to the pristine MIL-101(Cr) MOF, the as-prepared magnetic ternary nanocomposite (abbreviated as POM/CFO/MIL-101(Cr)) demonstrated a notable decrease in both the surface area and pore volume because of the incorporation of CoFe₂O₄ nanoparticles and huge P₂W₁₈O₆₂⁶⁻ polyanions into the cages of the MIL-101(Cr) framework. The POM/CFO/MIL-101(Cr) was then applied as a magnetically separable adsorbent for the rapid elimination of rhodamine B (RhB), methyl orange (MO), and methylene blue (MB) dye pollutants from aqueous solutions. For achieving the optimized conditions, the effects of initial pH, initial dye concentration, temperature, salt effect, and adsorbent dose on MB and RhB elimination were investigated. The dye adsorption isotherms followed the Langmuir model and pseudo-second-order kinetic model. The POM/CFO/MIL-101(Cr) composite material not only exhibited a fast adsorption rate towards dye molecules, but also demonstrated the selective adsorption of the cationic dyes in wastewater. The recycling experiments also demonstrated that the POM/CFO/MIL-101(Cr) adsorbent was highly stable and could be quickly recovered under a magnetic field without any alteration in the structure. The high adsorption capacity, simple fabrication method, rapid separation by a magnet and supreme reusability of the POM/CFO/MIL-101(Cr) nanocomposite make it an attractive adsorbent for the elimination of cationic dyes from wastewater.

The magnetic CoFe₂O₄/MIL-101 (Cr) metal–organic framework nanocomposite containing P₂W₁₈O₆₂⁶⁻ polyoxometalate was fabricated and applied as an ultrafast adsorbent to remove organic dyes from water.

Uniformly coating ZnAl layered double oxide nanosheets with ultra-thin carbon by ligand and phase transformation for enhanced adsorption of anionic pollutants

The increasing severity of water pollution has strongly urged to develop green and efficient adsorbents for waste-water treatment. In this work, ZnAl layered double oxide nanosheets uniformly coated with ultra-thin amorphous carbon shells (ZnAl-LDO@C) were fabricated by modifying ZnAl layered double hydroxides (LDHs) with molecular ligands followed by calcination. Compared with their counterparts derived from the pristine ZnAl-LDH, ZnAl-LDO@C nanosheets exhibit higher specific surface area with abundant and highly accessible active sites. The adsorption performance of the ZnAl-LDO@C nanosheets for methyl orange (MO) and hexavalent chromium [Cr(VI)] ions was investigated in detail. It is found that the channel-like hydrophilic carbon shells facilitate the diffusion of water molecules and ions, leading to the fast adsorption rate. In addition, the rich oxygen-containing functional groups in the amorphous carbon shells can efficiently improve the adsorption capacity through multiple interactions. As a result, ZnAl-LDO@C nanosheets exhibit superior adsorption performance for MO and Cr(VI), outperforming most LDH- or LDO-based adsorbents reported previously. Meanwhile, a new oriented overlapping intercalation mechanism for MO adsorption was proposed for the first time to clarify how MO molecules arrange at the interlayer space.

Property Characterization and Mechanism Analysis of Polyoxometalates-Functionalized PVDF Membranes by Electrochemical Impedance Spectroscopy

Polyoxometalates (POMs) has proved its advantage in constructing high-performance nanocomposite membranes such as catalytic membranes, adsorptive membranes, and forward osmosis membranes. However, it is challenging or tedious to characterize its distribution and effect on the membrane structures due to the equipment resolution limitation, discrete nano-scaled structures of POMs, and limited doping amount compared to the polymeric membrane matrix. In this paper, POMs-functionalized polyvinylidene fluoride (PVDF) membranes were fabricated by phase inversion combined with the sol-gel method, and electrochemical impedance spectroscopy (EIS) was utilized to analyze the nanocomposite membrane intrinsic properties. Through adjusting the additives in the sol-forming process, a set of membranes with varied intrinsic properties were developed accordingly. The wetting degree of the membranes related to the hydrophilic nature of the membrane surfaces had a crucial influence on the impedance measurements at the early stage. Through EIS analysis, it was demonstrated that the amination of the membrane matrix through (3-aminopropyl)trimethoxysilane (APTMS) treatment and the immobilization of POMs through electrostatic attraction would not generate new pore structures into the membrane and only alter the membrane surface roughness and composition. To my knowledge, it is the first time that EIS was utilized to characterize the hydrophilicity of the membranes and pore structures of the POMs-modified membranes. Our findings indicate that EIS can provide valuable information for probing the structures of other nano-materials-incorporated membranes.

Fe3O4/PVDF catalytic membrane treatment organic wastewater with simultaneously improved permeability, catalytic property and anti-fouling

Fe₃O₄/Polyvinylidene fluoride (PVDF) three-channel hollow fiber catalytic membrane was successfully fabricated via non-solvent induced phase inversion and used for organic wastewater degradation in this work. The effects of Fe₃O₄ nanoparticles addition on the surface and cross-section morphologies, hydrophilicity and thermal properties of the catalytic membrane were characterized by the field emission scanning electron microscopy (SEM), water contact angle and thermogravimetric analysis (TGA), respectively. The obtained catalytic membrane exhibited good hydrophilicity, a high pure water flux of 175.8 L m^-2 h^-1 and a high removal of methylene blue (up to 97.6%) with Fenton catalytic reaction. Meanwhile, the catalytic membrane shows excellent anti-fouling property due to the presence of Fenton reaction. Our results show that Fe₃O₄/PVDF three-channel hollow fiber catalytic membrane was a promising alternative for the degradation of organic contaminants.

Congo red filtration by polyacrylonitrile-based copolymer membranes

In this study, Congo red removal from wastewater by a filtration method was studied via membranes obtained from polyacrylonitrile-co-poly(2-ethylhexylacrylate) copolymers having various monomer ratios and polyacrylonitrile-co-poly(2-ethylhexylacrylate)/polyaniline blends with various polyaniline contents. It was found that the dye rejection value increased with acrylonitrile content in polyacrylonitrile-co-poly(2-ethylhexylacrylate) membranes. Also, blending copolymers with polyaniline enhanced the dye rejection rate. The performance of membranes showed incremental increase with increase in the polyaniline content. Both pH and concentration effects on the dye rejection rate of membranes were evaluated. The performance of polyacrylonitrile-co-poly(2-ethylhexylacrylate) membranes did not change significantly, whereas polyaniline-containing membranes had higher dye rejection rates at acidic pH levels. PAN(92)-co-P2EHA(8)-PANI(15%) demonstrated the highest dye rejection value of 99.7% at pH 3 when the feed concentration was 50 ppm. It also showed good resistance to increase in feed concentration. It had dye rejection values of 97.2% and 88.5% for 100 and 200 ppm feed concentrations, respectively.

Sorption of ionized dyes on high-salinity microalgal residue derived biochar: Electron acceptor-donor and metal-organic bridging mechanisms

Biochar (BC) has attracted much attention owing to its superior sorption capacity towards ionized organic contaminants. However, the mechanism of ionized organics sorption occurring within BC containing large amounts of minerals is still controversial. In this study, we demonstrate the physicochemical structure of high-salinity microalgal residue derived biochar (HSBC) and elucidate the corresponding sorption mechanisms for four ionized dyes along with determining the crucial role of involved minerals. The results indicate that sodium and calcium minerals mainly exist within HSBCs, and the pyrolysis temperature can dramatically regulate the phases and interfacial property of both carbon matrix and minerals. As a result, the HSBC shows a higher sorption potential, benefiting from abundant functional groups and high content of inorganic minerals. Using theoretical calculations, the activities of electron donor-acceptor interaction between HSBCs and different dyes are clearly illustrated, thereby identifying the critical role of Ca²⁺ in enhancing the removal of ionized dyes in HSBCs. In addition, Ca-containing minerals facilitate the sorption of ionized dyes in HSBCs by forming ternary complexes through metal-bridging mechanism. These results of mineral-induced dye sorption mechanisms help to better understand the sorption of ionized organics in high-salt containing BC and provide a new disposal strategy for hazardous microalgal residue, as well as provide a breakthrough in making the remediation of ionized organic contaminated microalgal residue derived absorbent feasible.

Construction of an Aminated MIL-53(Al)-Functionalized Carbon Nanotube for the Efficient Removal of Bisphenol AF and Metribuzin

A versatile organic-inorganic hybrid structure makes a metal-organic framework (MOF) an outstanding host for different kinds of guests; in addition, its easy pyrolysis nature has been proven to be useful as precursors in the construction of carbon-based materials with a special porous structure. Herein, a novel porous composite nanostructure of an aminated MIL-53(Al)@carbon nanotube (CNT) has been successfully constructed for the first time based on in situ synthesis combining the pyrolysis of ZIF-67. The resulting composite nanostructure was performed by the means of scanning electron microscopy, Brunauer-Emmett-Teller analysis, typical and high-resolution transmission electronic microscopy, X-ray photoelectron spectroscopy, etc. The results showed that a compact heterostructure has been formed between an aminated MIL-53(Al) and a CNT. The resulting composites, named N-MIL@CNT, represent distinct promoted activities in the removal of Bisphenol AF (BPAF) and Metribuzin from wastewater, and the maximum adsorption values were 274 mg/g (BPAF) and 213 mg/g (Metribuzin), which are larger than the results obtained by other MOF-based nanomaterials. The adsorption isotherm, kinetics, and thermodynamics were studied in detail, and the selective adsorption mechanism was also suggested. The excellent selectivity, reusability, and structure stability suggest the potential application of this composite nanostructure in the selective removal of BPAF or Metribuzin from the practical wastewater.

Synthesis of polyaluminium chloride/papermaking sludge-based organic polymer composites for removal of disperse yellow and reactive blue by flocculation

In this study, a series of polyaluminium chloride/papermaking sludge-based organic polymer (PAC-PSBF) composites with different PAC basicity and PAC/PSBF mass ratios were prepared from papermaking sludge. The basic properties of the aforementioned composites were characterized, and their flocculation efficiencies were studied in the disperse yellow (DY) and reactive blue (RB) dye removals. The results of the flocculation experiments demonstrated that PAC-PSBF composites performed better than PAC regardless of the PAC basicity or PAC/PSBF mass ratios. The composites with low PAC basicity were effective in DY and RB dye removals. PAC-PSBF composites with the same PAC basicity but higher PAC/PSBF mass ratios exerted more satisfactory color removals and floc properties in both DY and RB dye removals. PAC-PSBF composites were more pH-independent than PAC, and the excellent flocculation efficiencies of the composites was achieved at pH 4.0 to 8.0 in DY/RB dye removals. In brief, desirable flocculation efficiencies of the PAC-PSBF composites were obtained when PAC and PSBF were appropriately combined together.

Performance Evaluation of Pilot-scale Hybrid Anaerobic Baffled Reactor (HABR) to Process Dyeing Wastewater Based on Grey Relational Analysis

A pilot-scale six-compartment hybrid anaerobic baffled reactor (HABR) with effective volume of 18 m3 was used to treat dyeing wastewater. The HABR system was able to treat the wastewater efficiently after FeSO4 pretreatment, as indicated by removal efficiencies of 33.7% for chemical oxygen demand (COD), 39.9% for suspended solid (SS), and 22.5% for sulfate (SO42−) during steadily operational period. Gas chromatography–mass spectrometry (GC-MS) showed that the concentrations of alkanes, amides, organic acids, ketones, phenols, and esters were much lower in the effluent than those in the influent; many high-molecular-weight compounds such as cyclanes, quinolines, and phenols were successfully transformed to low-molecular-weight ones. As illustrated from the results of generalized grey relational analysis (GGRA), COD removal efficiency was more closely associated with flow rate, organic loading rate (OLR), water temperature, and influent SS among the whole selected possible factors. Based on the overall treating effectiveness and the GGRA study, the optimized operation strategy of the dyeing wastewater treatment by HABR was obtained as the hydraulic retention time (HRT) of 12 h for steady-state operation with an up-flow velocity of 1.7 m/h as well as OLR of 1.5–2.0 kg COD/(m3·d).

Gravity-driven catalytic nanofibrous membrane with microsphere and nanofiber coordinated structure for ultrafast continuous reduction of 4-nitrophenol

Silver loaded nanofibrous membrane with high catalytic performance for 4-nitrophenol under continuous gravity-driven filtration was developed in this study. A polydopamine (PDA) microsphere and nanofiber coordinated composite structure was fabricated through an in situ PDA synthesis to achieve a high catalyst loading and controllable residence time of 4-nitrophenol. The incorporated PDA microspheres played an important role for the enhancement of catalytic performance due to the increased surface area (23% increase compared with PAN and PAN-PDAs-Ag) and reduced membrane porosity. Silver loading amount and the residence time of 4-nitrophenol was increased by more than 108% (from 1.2 wt% to 2.5 wt%) and 45% (from 0.79 s to 1.15 s) when comparing with PAN-PDAc-Ag and PAN-PDAs-Ag nanofibrous membrane. The conversion rate of 4-nitrophenol in a gravity-driven filtration process was as high as 97% when PAN-PDAs-Ag nanofibrous membrane was used, which was much higher than the PAN-PDAc-Ag membrane (80%). In addition, the PAN-PDAs-Ag nanofibrous membrane exhibited excellent recycle performance, the conversion rate was maintained as high as 93% after five times of reuse. The microsphere and nanofiber coordinated structure with enhanced surface area and controllable residence time of contaminants proposed in this study might advance the real applications of electrospun nanofibrous membrane for catalytic removal of contaminants.

Polyethylene Glycol-Modified Layered Double Hydroxides: Synthesis, Characterization, and Study on Adsorption Characteristics for Removal of Acid Orange II from Aqueous Solution

The present study aimed to improve the adsorption characteristics of the pristine layered double hydroxide (LDH) by physicochemical modification using polyethylene glycol (PEG400), a nontoxic hydrophilic polymer. With this objective, LDH was synthesized and modified with different concentrations of PEG400. The PEG-modified LDHs (LDH/PEGs) were characterized using X-ray diffraction, thermogravimetric analysis, Brunauer-Emmett-Teller surface area and porosity measurement, scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, and zeta potential measurements. The adsorption properties of the pristine LDH (PLDH) and the LDH/PEGs were studied for the removal of Acid Orange II from water, and the results were compared. The PLDH treated with 15% PEG solution showed ∼30% increase in adsorption capacity as compared to the PLDH. The adsorption isotherm data were analyzed using Langmuir, Freundlich, and Temkin isotherm models. The values of thermodynamic parameters such as ΔS and ΔH showed the spontaneous and endothermic nature of the adsorption process. The adsorption kinetics data for both PLDH and the LDH/PEG adsorbents presented a good fit to the pseudo-second-order kinetic model.

Application of response surface methodology in physicochemical removal of dyes from wastewater: A critical review

Response surface methodology (RSM) is a powerful tool in designing the experiments and optimizing different environmental processes. However, when it comes to wastewater treatment and specifically dye-containing wastewater, two questions arise; "Is RSM being used correctly?" and "Are all capabilities of RSM being exploited properly?". The current review paper aims to answer these questions by scrutinizing different physicochemical processes that utilized RSM in dye removal. The literature that applied RSM to adsorption, advanced oxidation processes, coagulation/flocculation and electrocoagulation processes were critically reviewed in this paper. The common errors in applying RSM to physicochemical removal of dyes are identified and some suggestions are made for future studies.

Visible-light-assisted photocatalytic activity of bismuth-TiO2 nanotube composites for chromium reduction and dye degradation

TiO₂ nanotubes (TNTs) were synthesized on a Ti sheet using the electrochemical anodization method. Bismuth (Bi) was coupled on the anodized TNTs via hydrothermal process. We verified the effect of different Bi concentrations on the photocatalytic properties of Bi-TNT composites. The obtained samples were characterized using field emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, Raman spectroscopy, UV-Vis diffuse reflectance spectra, and photoluminescence spectra. The Bi-TNT photocatalysts exhibited higher activities by factors of 6.6 and 3.6 toward chromium reduction and methylene blue degradation, respectively, under visible light than the pure TNTs. The Bi-TNT material was recycled to examine the stability of the catalyst. The quantum efficiency of the photocatalytic system was calculated, and the synergistic effects of bismuth modification were discussed. The Bi-TNT composites were observed to be promising for separation of photoinduced e^- and h⁺ by decreasing charge recombination, and helped the formation of the hydroxyl radicals, h⁺, and superoxides used in the photocatalytic process.