Immobilization of uranium by biomaterial stabilized FeS nanoparticles: Effects of stabilizer and enrichment mechanism

Green preparation of regenerable biohybrids with xanthan gum-stabilized biogenic mackinawite nanoparticles for efficient treatment from high-concentration uranium wastewater

The high efficiency, economy, sustainability and no secondary pollution of U(VI) removal is an important and challenging topic for U(VI) wastewater treatment. Here, the regenerable biohybrids with xanthan gum (XG) stabilized biogenic mackinawite nanoparticles (BX-FeS) were prepared, where XG acted as carrier facilitated the Fe2+ attachment and induced the low size, high stability and activity of nearly spherical FeS nanoparticles. Results showed that BX-FeS kept high activity after storing two years and good performance for U(VI) removal in broad pH range and co-existence of ions, and had greater removal efficiency (97.9 %) than biogenic B-FeS (67.1 %). Moreover, BX-FeS preformed high adsorption capacity in uranium wastewater (658.0 mg/g), and lower cost compared with zerovalent-iron and silica gel. Importantly, BX-FeS maintained high activity within three regeneration cycles driven by Desulfovibrio desulfuricans, inhibited the secondary pollution (Fe3+, SO42-) of reaction. This study provides a new strategy for sustainable and efficient treatment of U(VI) wastewater.

Desulfovibrio-induced gauzy FeS for efficient hexavalent chromium removal: The influence of SRB metabolism regulated by carbon source and electron carriers

Biosynthetic metal sulfides showed great application prospects in the environmental treatment against high-valence metal pollutants. However, the efficiency of biosynthesis, agglomeration during the reaction process, and the formation of the passivation layer during the reduction process were always the important factors restricting its development. This study explored the composition of the culture medium to promote the growth of highly corrosive sulfate-reducing bacteria (SRB) and its metabolism to produce FeS nanoparticles (NPs). The results showed that reducing the carbon source (CS) and adding electron carriers in the culture medium effectively promoted the production of small, dispersed, and loose FeS NPs in cells. At pH = 7, 24 °C and 10 min reaction time, 0.1 g/L FeS NPs produced by SRB under the conditions of 10 % CS with 10 ppm cytochrome c medium could achieve 100 % removal efficiency of 1 mM hexavalent chromium (Cr(VI)). Under this condition, FeS NPs could be produced by intracellular metabolism in SRB cells, and environmental factors such as pH, metal cations, and Cl- had little effect on the removal of Cr(VI) by this FeS NPs. The surface proteins of FeS NPs significantly enhanced their antioxidant properties. After 7 days of natural environment exposure, the Cr(VI) removal efficiency of FeS NPs was only reduced by 16 % compared with the initial sample. This work provided an in-depth understanding of Cr(VI) removal by SRB biosynthesis of FeS and contributes to the widespread application of FeS in the future.

Removal of toxic metals using iron sulfide particles: A brief overview of modifications and mechanisms

Growing mechanization has released higher concentrations of toxic metals in water and sediment, which is a critical concern for the environment and human health. Recent studies show that naturally occurring and synthetic iron sulfide particles are efficient at removing these hazardous pollutants. This review seeks to provide a concise summary of the evolution in the production of iron sulfide particles, specifically nanoparticles, through the years. This review presents an outline of the synthesis process for the most dominant forms of iron sulfide: mackinawite (FeS), pyrite (FeS2), pyrrhotite (Fe1-x S), and greigite (Fe3S4). The review confirms that both natural forms of iron sulfide and modified forms of iron sulfide are highly effective at removing different heavy metals and metalloids from water. Concurrently, this review reveals the interaction mechanism between toxic metals and iron sulfide, along with the impact of conditions for remedy and rectification. None the less, modifications and future investigations into the synthesis of novel iron sulfides, their use to adsorb diverse environmental pollutants, and their fate after injection into polluted aquifers, remain crucial to maximizing pollution control.

Stable and recyclable FeS-CMC-based peroxydisulfate activation for effective bisphenol A reduction: performance and mechanism

In this study, a novel material, iron sulfide modified by sodium carboxymethyl cellulose (FeS-CMC), was successfully synthetized for peroxydisulfate (PDS) activation to remove bisphenol A (BPA). Characterization results showed that FeS-CMC had more attachment sites for PDS activation due to its higher specific surface area. A stronger negative potential contributed to preventing nanoparticles from reuniting in the reaction and improving the interparticle electrostatic interactions of the materials. Fourier transform infrared spectrometer (FTIR) analysis of FeS-CMC suggested that the coordination of the ligand for combining sodium carboxymethyl cellulose (CMC) with FeS was monodentate. A total of 98.4% BPA was decomposed by the FeS-CMC/PDS system after 20 min under optimized conditions (pH = 3.60, [FeS-CMC] = 0.05 g/L and [PDS] = 0.88 mM). The isoelectric point (pH_pzc) of FeS-CMC is 5.20, and FeS-CMC contributed to reducing BPA under acidic conditions but showed a negative effect under basic conditions. The presence of HCO₃^-, NO₃^- and HA inhibited BPA degradation by FeS-CMC/PDS, while excess Cl^- accelerated the reaction. FeS-CMC exhibited excellent performance in oxidation resistance with a final removal degree of 95.0%, while FeS was only 20.0%. Furthermore, FeS-CMC showed excellent reusability and still reached 90.2% after triple reusability experiments. The study confirmed that the homogeneous reaction was the primary part of the system. Surface-bound Fe(II) and S (-II) were found to be the major electron donors during activation, and the reduction of S (-II) contributed to the cycle of Fe(III)/Fe(II). Sulfate radicals (SO₄^•-), hydroxyl radicals (•OH), superoxide radicals (O₂^•-) and singlet oxygen (¹O₂) were produced at the surface of FeS-CMC and accelerated the decomposition of BPA. This study offered a theoretical basis for improving the oxidation resistance and reusability of iron-based materials in the presence of advanced oxidation processes.

Remediation of Cr(VI) contaminated soil by chitosan stabilized FeS composite and the changes in microorganism community

In-suit immobilization is one of the major strategies to remediate heavy metals contaminated soil with the effectiveness largely depends on the characteristics of the added chemical reagents/materials. In this study, chitosan stabilized FeS composite (CS-FeS) was prepared to evaluate the performance of remediating the high and toxic hexavalent chromium contaminated soil from the effectiveness and microbial response aspects. The characterization analysis confirmed the successful preparation of composite, and the introduction of chitosan successfully stabilized FeS to protect it from rapid oxidation as compared to bare FeS particles. With the addition dosage at 0.1%, about 85.6% and 81.3% of Cr(VI) was reduced in 3 d based on toxicity characteristic leaching procedure (TCLP) and CaCl₂ extraction, and the reduction efficiency increased to 96.6% and 94.8% in 7 d, respectively. The Cr(VI) was non-detected in the TCLP leachates with increase the CS-FeS composites to 0.5%. The percentages of HOAc-extractable Cr decreased from 25.17% to 6.12% accompanied with the increase in the residual Cr from 4.26% to 13.77% and improvement of soil enzyme activity under CS-FeS composites addition. Cr(VI) contamination reduced the diversity of microbial community in soil. Three dominate prokaryotic microorganisms, namely Proteobacteria, Actinobacteria and Firmicutes, were observed in Cr-contaminated soil. The addition of CS-FeS composites increased the microbial diversity especially for that in relative lower abundance. The relative abundance of Proteobacteria and Firmicute related to Cr-tolerance and reduction increased in CS-FeS composites added soils. Taking together, these results demonstrated the potential and promising of using the CS-FeS composites for Cr(VI) polluted soil remediation.

High efficiency electrochemical separation of uranium(VI) from uranium-containing wastewater by microbial fuel cells with different cathodes

As an emerging versatile technology for separating uranium from uranium-containing wastewater (UCW), microbial fuel cell (MFC) offers a novel approach to UCW treatment. Its cathode is essential for the treatment of UCW. To thoroughly investigate the efficacy of MFC in treating UCW, investigations were conducted using MFCs with five materials (containing iron sheet (IP), stainless steel mesh (SSM), carbon cloth (CC), carbon brush (CB), and nickel foam (NF)) as cathodes. The results revealed that each MFC system performed differently in terms of carbon source degradation, uranium removal, and electricity production. In terms of carbon source degradation, CB-MFC showed the best performance. The best uranium removal method was NF-MFC, and the best electricity production method was carbon-based cathode MFC. Five MFC systems demonstrated stable performance and consistent difference over five cycles, with CC-MFC outperforming the others. Furthermore, SEM and XPS characterization of the cathode materials before and after the experiment revealed that a significant amount of U(IV) was generated during the uranium removal process, indicating that uranium ions were primarily removed by electrochemical reduction precipitation. This study confirmed that abiotic cathode MFC had a high UCW removal potential and served as a good guideline for obtaining the best cathode for MFC.

Surface Engineering Design of Nano FeS@Stenotrophomonas sp. by Ultrasonic Chemical Method for Efficient U(VI) and Th(IV) Extraction

Nano-FeS has great potential for use in the management of radioactive contaminants. In this paper, we prepared a FeS@Stenotrophomonas sp. composite material by ultrasonic chemistry, and it showed excellent removal of uranium and thorium from the solution. Through optimization of the experimental conditions, it was found that the maximum adsorption capacities for uranium and thorium reached 481.9 and 407.5 mg/g for a composite made with a synthetic ratio of 1:1, pH 5 and 3.5, respectively, for U and Th, and sonication for 20 min. Compared with those of FeS or Stenotrophomonas alone, the removal capacity was greatly improved. The results of a mechanistic study indicated that efficient removal of the uranium and thorium was due to ion exchange, reduction, and microbial surface adsorption. FeS@Stenotrophomonas sp. could be applied to U(VI) and Th(IV) extraction for radioactive water.

A bioinspired polydopamine-FeS nanocomposite with high antimicrobial efficiency via NIR-mediated Fenton reaction

Ferrous and sulfur ions are essential elements for the human body, which play an active role in maintaining the body's normal physiology. Meanwhile, mussel-inspired polydopamine (PDA) possesses good hydrophilicity and biocompatibility. In the present work, ferrous sulfide embedded into polydopamine nanoparticles (PDA@FeS NPs) was designed and synthesized via a simple predoping polymerization-coprecipitation strategy and the intelligent PDA matrix successfully prevented the oxidation and agglomeration of FeS nanoparticles. Importantly, there was an obvious synergistic enhancement of the photothermal effect between polydopamine and ferrous sulfide. The PDA@FeS NPs exhibited excellent photothermal antibacterial effects against both E. coli and S. aureus. The near-infrared (NIR) light-mediated release of ferrous ions could reach about 26.5% under weakly acidic conditions, further triggering the Fenton reaction to produce toxic hydroxyl radicals (·OH) in the presence of hydrogen peroxide. The antibacterial mechanism could be attributed to cell membrane damage and cellular content leakage with the synergistic effect of PTT and CDT. This study highlighted the germicidal efficacy of PDA@FeS NPs and provided a new strategy for designing and developing next-generation antibacterial platforms.

High-efficiency Hg(II) adsorbent: FeS loaded on a carbon black from pyrolysis of waste tires and sequential reutilization as a photocatalyst

Iron-sulfur nano compounds have been proven to be effective in mercury removal, but the agglomeration, poor dispersion and mobility, and easy oxidation challenges limit their application. Herein, carbon black originating from pyrolysis of waste tires was used as a carrier of nano-FeS to obtain an efficient adsorbent (C@PDA-FeS). It is found that the C@PDA-FeS shows outstanding adsorption ability, excellent selectivity, and high removal rate. A maximum adsorption capacity of 1754 mg/g is obtained, and the residual Hg(II) ion concentration is as low as 3.2 μg/L in the simulated industrial wastewater, which meets the industrial discharge standard under the optimal conditions. Meanwhile, the removal rate of Hg(II) ion can reach 99.8% after up to 10 cycles. More importantly, the C@PDA-FeS still shows good adsorption efficiency, and the removal rate of Hg(II) ion is over 99% (25 mg/L Hg(II) concentration) after 90 days of storage, demonstrating the long-term stability and promising future of the adsorbent. In addition, the waste adsorbent (C@PDA-FeS/HgS) is reused as a photocatalyst to degrade methylene blue, and the corresponding degradation rate is 92.9% (10 mg/L).

Efficient charge separation in sulfur doped AgFeO2 photocatalyst for enhanced photocatalytic U(VI) reduction: The role of doping and mechanism insights

Photocatalytic reduction of U(VI) in aqueous solutions has been considered as an efficient and promising technology to solve radioactive U pollution. In this work, density functional theory (DFT) calculations were firstly employed to optimize and compare the adsorption configurations combined uranium with four given photocatalysts, then their adsorption energies were - 0.97 eV for AgFeO₂, - 1.15 eV for Zn doped AgFeO₂, - 1.73 eV for Cu doped AgFeO₂ and - 2.66 eV for S doped AgFeO₂, respectively, indicating the sulfur doping plays a major role in U(VI) photoreduction. Herein, a visible light responsive efficient sulfur doped AgFeO₂ photocatalyst (S doped AgFeO₂) was synthesized and utilized to photocatalytic reduction of U(VI) in aqueous solutions. According to XRD, XPS and TEM analysis, the sulfur was successfully doped in AgFeO₂ via the hydrothermal method. The batch experimental showed that S doping enhanced the U(VI) photoreduction activity of AgFeO₂, and the S-AFO-3 photocatalyst exhibited the highest photocatalytic activity (92.57%), which was 1.5 times than that of pure AgFeO₂. ESR, PL and DFT results demonstrated that the enhancement of adsorbed U(VI) photoreduction was attributed to the own unique effect of oxygen vacancy defects and efficient charge separation of S doped AgFeO₂ photocatalyst. Due to its higher adsorption energies, fast-U(VI) photoreduction rate and superior chemical stability, the sulfur doped AgFeO₂ photocatalyst is hoped for water remediation containing U(VI) wastewater.

Valence regulation investigation of key factors on the electrochemical immobilization uranyl from wastewater

Electrochemical techniques are considered promising applications to immobilize uranium in alkaline wastewater in order to prevent its migration into groundwater and soil. In this work, the results of electrochemical and Atomic Force Microscope (AFM) demonstrate a successful immobilization of uranyl in the carbonate system by U(VI)-U(V), U(V)-U(IV) reduction, and U(V) disproportionation reactions. The results indicated that the electrochemical fixation rate in alkaline system could reach more than 99%. The valence state of uranium is the key factor affecting its migration in the working system. Where, the analysis of the immobilized samples by X-ray photoelectron spectroscopy (XPS) revealed that pHs, current density, and the presence of foreign cations significantly affect the valence state of uranium in the immobilized samples. Under same conditions, the reduction reactions of U(VI)-U(V) and U(V)-U(IV) occurred easily. Where, at pH higher than 3.4 or the current density in the range of 0.5-20 mA/cm², high content of U(V) and U(IV) in the immobilized products was obtained. Other conditions favored the occurrence of the electrolytic water reaction, and the immobilized samples were dominated by U(VI). It was found that the temperature showed the greatest effect on the electrochemical immobilization rate. Where, the electrochemical immobilization rate increased by about 1.8 times when the ambient temperature increased from 293.15 to 328.15 K. This study provides a new idea for the immobilization of uranium in alkaline wastewater and demonstrates the feasibility of electrochemical immobilization of uranium in alkaline systems.

Removal of heavy metal(loid)s from aqueous solution by biogenic FeS-kaolin composite: Behaviors and mechanisms

In this work, a green adsorbent, biogenic FeS-kaolin composite (KL-FeS) was synthesized by sulfate-reducing bacteria (SRB) mediation, and its potential for Cd(II), Pb(II), Cu(II), Zn(II), As(III) and Sb(III) removal was evaluated. Among prepared composites, the KL-FeS synthesized at a concentration of 2 g/L kaolin performed a better removal efficiency on heavy metal(loid)s and the adsorption results followed the pseudo-second-order and Redlich-Peterson models, indicating that the adsorption was a hybrid chemical reaction-adsorption process. Additionally, the maximum adsorption capacities of Cd(II), Pb(II), Cu(II), Zn(II), As(III) and Sb(III) on KL-FeS in monocomponent system were 71.71, 133.54, 51.90, 54.41, 38.71 and 96.38 mg/g, respectively (pH = 5.0 ± 0.1, T = 25 °C). In addition, the increase of pH and ionic strength promoted the adsorption capacities of KL-FeS for metal-(loid)s. Moreover, FTIR, XPS and XRD analyses supported that surface complexation, hydrogen bonding, ion exchange, electrostatic interaction and chemical precipitation were predominately mechanisms involved in the adsorption process. Furthermore, KL-FeS displayed higher affinity for Pb(II), Sb(III) and Cu(II) in the multi-component system. This work highlighted the potential of biogenic FeS-kaolin composite for simultaneous removal of multiple heavy metal(loid)s under aerobic conditions.

Cellulose Structures as a Support or Template for Inorganic Nanostructures and Their Assemblies

Cellulose is the most abundant natural polymer and deserves the special attention of the scientific community because it represents a sustainable source of carbon and plays an important role as a sustainable energent for replacing crude oil, coal, and natural gas in the future. Intense research and studies over the past few decades on cellulose structures have mainly focused on cellulose as a biomass for exploitation as an alternative energent or as a reinforcing material in polymer matrices. However, studies on cellulose structures have revealed more diverse potential applications by exploiting the functionalities of cellulose such as biomedical materials, biomimetic optical materials, bio-inspired mechanically adaptive materials, selective nanostructured membranes, and as a growth template for inorganic nanostructures. This article comprehensively reviews the potential of cellulose structures as a support, biotemplate, and growing vector in the formation of various complex hybrid hierarchical inorganic nanostructures with a wide scope of applications. We focus on the preparation of inorganic nanostructures by exploiting the unique properties and performances of cellulose structures. The advantages, physicochemical properties, and chemical modifications of the cellulose structures are comparatively discussed from the aspect of materials development and processing. Finally, the perspective and potential applications of cellulose-based bioinspired hierarchical functional nanomaterials in the future are outlined.

Carboxymethyl cellulose stabilized ferrous sulfide@extracellular polymeric substance for Cr(VI) removal: Characterization, performance, and mechanism

Iron-based materials, especially ferrous sulfide (FeS), effectively remediate chromium pollution. However, the agglomeration of FeS reduces its reactivity to chromium. Herein, carboxymethyl cellulose stabilized ferrous sulfide@extracellular polymeric substance (CMC-FeS@EPS) was developed to remove hexavalent chromium (Cr(VI)) from water. CMC-FeS@EPS (98.00%) exhibited excellent removal efficiency of 40 mg/L Cr(VI) than those of FeS (57.35%) and CMC-FeS (68.60%). CMC-FeS@EPS showed good removal efficiency of Cr(VI) in wide pH range (from 4 to 9) and the co-existence of ions. FTIR and XPS results demonstrated that EPS functional group accelerated the process of adsorption and precipitation. Electrochemical results showed that CMC-FeS@EPS transferred electrons to Cr(VI) faster than CMC-FeS. In total, this study started from a new idea of using EPS to improve the performance of CMC-FeS, and provided a simple and effective way to remediate chromium pollution without secondary pollution.

Biochar-supported starch/chitosan-stabilized nano-iron sulfide composites for the removal of lead ions and nitrogen from aqueous solutions

Novel materials that nano-FeS and starch (or chitosan) loaded on peanut shells biochar(Starch-FeS@PSB and Chitosan-FeS@PSB) were prepared and applied for removal of Pb(II) and nitrogen(NO₃-N and NH₄-N) in wastewater. It showed that Starch-FeS@PSB and Chitosan-FeS@PSB had excellent absorptive effects compared with PSB. The maximum adsorption capacity of Pb(II) by Starch-FeS@PSB and Chitosan-FeS@PSB reached 91.74 mg/g, 98.04 mg/g, respectively. Absorption of Pb(II) by Starch-FeS@PSB and Chitosan-FeS@PSB were controlled by monolayer chemisorption. Mechanism studies showed that complexation, electrostatic attraction, REDOX and physical absorption happened on the adsorbent surface. In addition, the maximum adsorption capacity of NO₃-N and NH₄-N by Starch-FeS@PSB and Chitosan-FeS@PSB reached 16.89 mg/g, 15.65 mg/g, and 18.45 mg/g, 18.28 mg/g, respectively. Absorption of N by Starch-FeS@PSB and Chitosan-FeS@PSB were controlled by multilayer chemisorption. Mechanism studies showed that complexation, electrostatic attraction and physical absorption happened on the adsorbent surface. Starch-FeS@PSB and Chitosan-FeS@PSB can be utilized in Pb(II) and N wastewater treatment.

Effective lead passivation in soil by bone char/CMC-stabilized FeS composite loading with phosphate-solubilizing bacteria

Bioremediation by phosphate-solubilizing bacteria (PSB) has attracted extensive attentions due to its economical and eco-friendly properties for lead (Pb) passivation in soil. Herein, bone char (BC) supported biochemical composite (CFB₁-P) carrying advantages of BC, PSB, iron sulfide (FeS) and carboxymethyl cellulose (CMC) was designed and applied to Pb passivation. The composite at a mass ratio of BC:CMC:FeS = 1:1:1 possessed high passivation efficiency (65.47%), and has been demonstrated to offer appropriate habitat environment for PSB to defend against Pb(II) toxicity, thus enhancing the phosphate-solubilizing amount of PSB to 140.72 mg/L for passivating Pb(II). Batch experiments showed that the CFB₁-P possessed excellent adsorption properties with maximal monolayer Pb(II) uptake of 452.99 mg/g during an extensive pH range of 2.0-6.0. Furthermore, by applying CFB₁-P dosage of 3% into Pb-contaminated soil, the labile Pb fractions were reduced from 29.05% to 6.47% after simulated remediation of 10 days, and converted into steady fractions. The CFB₁-P was demonstrated to achieve high Pb(II) passivation through combined functions of chemical precipitation, complexation, electrostatic attraction and biomineralization, accompanied by the formation of more stable crystal structures, for instance, Pb₅(PO₄)₃OH, Pb₃(PO₄)₂ and PbS. These results suggested CFB₁-P as a potential alternative for efficient remediation of Pb-contaminated soil.

Inhibitory effect and mechanism of gelatin stabilized ferrous sulfide nanoparticles on porcine reproductive and respiratory syndrome virus

Background

The infection and spread of porcine reproductive and respiratory syndrome virus (PRRSV) pose a serious threat to the global pig industry, and inhibiting the viral infection process is a promising treatment strategy. Nanomaterials can interact with viruses and have attracted much attention due to their large specific surface area and unique physicochemical properties. Ferrous sulfide nanoparticles (FeS NPs) with the characteristics of high reactivity, large specific surface area, and low cost are widely applied to environmental remediation, catalysis, energy storage and medicine. However, there is no report on the application of FeS NPs in the antiviral field. In this study, gelatin stabilized FeS nanoparticles (Gel-FeS NPs) were large-scale synthesized rapidly by the one-pot method of co-precipitation of Fe²⁺ and S^2‒.

Results

The prepared Gel-FeS NPs exhibited good stability and dispersibility with an average diameter of 47.3 nm. Additionally, they were characterized with good biocompatibility and high antiviral activity against PRRSV proliferation in the stages of adsorption, invasion, and replication.

Conclusions

We reported for the first time the virucidal and antiviral activity of Gel-FeS NPs. The synthesized Gel-FeS NPs exhibited good dispersibility and biocompatibility as well as effective inhibition on PRRSV proliferation. Moreover, the Fe²⁺ released from degraded Gel-FeS NPs still displayed an antiviral effect, demonstrating the advantage of Gel-FeS NPs as an antiviral nanomaterial compared to other nanomaterials. This work highlighted the antiviral effect of Gel-FeS NPs and provided a new strategy for ferrous-based nanoparticles against PRRSV.

Graphical Abstract

Supplementary Information

The online version contains supplementary material available at 10.1186/s12951-022-01281-4.

Cr(VI) immobilization by FeS-coated alumina and silica: Effects of pH and surface coating density

We investigated the feasibility of using FeS-coated alumina and silica for permeable reactive barrier (PRB) applications. By both coated materials, Cr(VI) was reduced to Cr(III), which was immobilized via surface complexation/precipitation at acidic pH, and bulk precipitation at neutral to basic pH. Both pH and surface coating density (the amount of FeS deposits per unit surface area of a supporting matrix) controlled Cr(VI) reduction capacity and [Cr,Fe](OH)₃ composition. The reduction was higher at acidic pH due to lower passivation, as evidenced by the increased production of Fe(III) (oxyhydr)oxides over Fe(II)-Fe(III) phases. The coated alumina, despite the lower amount of FeS deposits than the coated silica, showed greater reduction capacities due to its higher surface coating density, which made Fe(III) closer together to favor Fe(III) (oxyhydr)oxide formation. Since Cr(III) was preferentially substituted for Fe(III) in Fe(III) (oxyhydr)oxides, lower pH and higher surface coating density led to lower Cr fractions in [Cr,Fe](OH)₃ because of the increased production of Fe(III) (oxyhydr)oxides. Given that Cr-poor [Cr,Fe](OH)₃ is more resistant to re-oxidation, FeS-coated alumina is better for PRB applications. This study reveals the significance of the surface coating density when evaluating the effectiveness of coated materials in redox-based treatments.

Mechanism of efficient remediation of U(VI) using biogenic CMC-FeS complex produced by sulfate-reducing bacteria

Uranium in groundwater during uranium mining activities urgently needs to be remediated through effective and environmental-friendly approaches. The reduction and immobilization of soluble U(VI) using biogenic carboxymethyl cellulose modified iron sulfide complex (biogenic CMC-FeS complex) is one of the emerging and innovative methods. However, its removal mechanism is largely unknown. Here, biogenic CMC-FeS complex with extracellular polymeric substances (EPS) and CMC was successfully synthesized by sulfate-reducing bacteria (SRB) and showed highly dispersible capacity. The tryptophan and tyrosine, which were the main components in EPS produced by SRB on CMC-FeS surface, significantly increased the U(VI) removal capacity of the biogenic CMC-FeS complex compared with chemically synthesized CMC-FeS. U(VI) removal was attributed to the adsorption of soluble U(VI) by ≡FeO⁺, CMC, tryptophan, and tyrosine on the biogenic CMC-FeS complex, following its reduction by S^2-, S₂^2- and Fe²⁺. Moreover, biogenic CMC-FeS complex with CMC-to-FeS molar ratio of 0.0005 performed well in the presence of bicarbonate (5 mM), humic acid (10 mg/L), or co-existing cations such as Pb²⁺, Ni²⁺, Cd²⁺, Mn^2+, and Cu²⁺ (200 ug/L) at pH 7.0, and displayed relatively high oxidation resistance and stability ability. This work provides an in-depth understanding of the biogenic CMC-FeS complex for the U(VI) removal and contributes to the development of cost-effective U(VI) remediation technologies.

A non-polluting method for rapidly purifying uranium-containing wastewater and efficiently recovering uranium through electrochemical mineralization and oxidative roasting

Iron-based materials have been widely used for treating uranium-containing wastewater. However, the iron-uranium solids originating by treating radioactive water through pollutant transfer methods has become a new uncontrolled source of persistent radioactive pollution. The safe disposal of such hazardous waste is not yet well-resolved. The electrochemical mineralization method was developed to rapidly purify uranium-containing wastewater through lattice doping in magnetite and recover uranium without generating any pollutants. An unexpected isolation of U₃O₈ from uranium-doped magnetite was discovered through in-situ XRD with a temperature variation from 300 °C to 700 °C. Through HRTEM and DFT calculation, it was confirmed that the destruction of the inverse spinel crystal structure during the gradual transformation of magnetite into γ-Fe₂O₃ and α-Fe₂O₃ promoted the migration, aggregation, and isolation of uranium atoms. Uniquely generated U₃O₈ and Fe₂O₃ were easily separated and over 80% uranium and 99.5% iron could be recovered. These results demonstrate a new strategy for uranium utilization and the environmentally friendly treatment of uranium-containing wastewater.

In situ prepared algae-supported iron sulfide to remove hexavalent chromium

The effects of algae on the removal of contaminant by iron sulfide (FeS) are still unknown. Chlorella vulgaris (CV), a remarkable algal specie, was used to prepare the CV-supported FeS (CV-FeS) and to investigate the role that CV plays in the removal of a heavy metal (i.e., hexavalent chromium (Cr(VI)) by FeS. The stabilized effect from algal extracellular polymeric substance (EPS) enhanced the reactivity of FeS due to the decrease of FeS aggregation, thus increasing Cr(VI) removal rate from 0.21 min^-1 to 0.79 min^-1. Furthermore, the strong buffering induced by the algal functional groups could effectively prevent the solution pH from increasing, which improved Cr(VI) removal because acidic solution facilitated Cr(VI) reduction by FeS. However, the complexing capacity from algal EPS made Fe(II) unavailable for Cr(VI) reduction, which led to 35% decrease of Cr(VI) removal. The Fe(II) was oxidized to α-FeOOH by Cr(VI) in the absence of CV, while the unreacted Fe(II) was detected as in the form of Fe(OH)₂ in CV-FeS. Cr(VI) was reduced to Cr(III) and S(-II) was oxidized to elemental sulfur (S₈) regardless of the CV. This work showed the different roles of algae in the removal of Cr(VI) by FeS and provided value information for the application of FeS in the polluted algae-containing water system.

Facile preparation and adsorption performance of low-cost MOF@cotton fibre composite for uranium removal

A novel composite MOF@cotton fibre (HCF) was prepared and characterized by FTIR, SEM, XPS and TGA. The effect of various parameters on the adsorption efficiency, such as the solution pH, contact time, initial U(VI) concentration and temperature, was studied. The maximal sorption capacity (Qm) is 241.28 mg g-1 at pH 3.0 for U(VI) according to the Langmuir isotherm adsorption model, and the kinetic and thermodynamic data reveal a relatively fast entropy-driven process (ΔH0 = 13.47 kJ mol-1 and ΔS0 = 75.47 J K-1 mol-1). The removal efficiency of U(VI) by HCF is comparable with that of pure cotton fibre and as-prepared MOF (noted as HST). However, the HST composite with cotton fibre significantly improved the treatment process of U(VI) from aqueous solutions in view of higher removal efficiency, lower cost and faster solid-liquid separation. Recycling experiments showed that HCF can be used up to five times with less than 10% efficiency loss.

Ultrahigh sorption and reduction of Cr(VI) by two novel core-shell composites combined with Fe3O4 and MoS2

In this investigation, two novel magnetic core-shell Fe₃O₄@MoS₂ (F@M) and MoS₂@Fe₃O₄ (M@F) composites were synthesized and exploited for Cr(VI) elimination. Eco-friendly preparation methods were applied for the synthesis of Fe₃O₄ and MoS₂ composites. The experimental results showed that both F@M and M@F have high saturation magnetization values (43.2 emu/g for F@M and 49.9 emu/g for M@F), excellent maximum sorption capacities of Cr(VI) at pH 5.0 and 298 K (324.3 mg/g for F@M, 290.2 mg/g for M@F), remarkable Cr(VI) removal efficiencies (Cr(VI) sorption equilibrium by both F@M and M@F can be reached in 90 min) and nice regeneration properties (the sorption capabilities of F@M and M@F decreased slightly after five consecutive sorption/desorption cycles). Chemical reduction of Cr(VI) to Cr(III) occurred on the surface of F@M and M@F, and the synergetic reduction of sulfur and ferrous ions made F@M an outstanding material for Cr(VI) removal. This paper highlights F@M and M@F as potential, eco-friendly and ultrahigh-efficiency materials for Cr(VI) pollution cleanup.

Two-dimensional MAX-derived titanate nanostructures for efficient removal of Pb(ii)

Two-dimensional (2D) nanomaterials have been identified as one of the promising materials due to their great promise for waste treatment.

In Situ Anchoring of Pyrrhotite on Graphitic Carbon Nitride Nanosheet for Efficient Immobilization of Uranium

Enrichment of U^VI is an urgent project for nuclear energy development. Herein, magnetic graphitic carbon nitride nanosheets were successfully prepared by in situ anchoring of pyrrhotite (Fe₇ S₈ ) on the graphitic carbon nitride nanosheet (CNNS), which were used for capturing U^VI . The structural characterizations of Fe₇ S₈ /CNNS-1 indicated that the CNNS could prevent the aggregation of Fe₇ S₈ and the saturation magnetization was 4.69 emu g^-1 , which meant that it was easy to separate the adsorbent from the solution. Adsorption experiments were performed to investigate the sorption properties. The results disclosed that the sorption data conformed to the Langmuir isotherm model with the maximum adsorption capacity of 572.78 mg g^-1 at 298 K. The results of X-ray photoelectron spectroscopy (XPS) demonstrated that the main adsorption mechanism are as follows: U^VI is adsorbed on the surface of Fe₇ S₈ /CNNS-1 through surface complexation initially, then it was reduced to insoluble U^IV . Thereby, this work provided an efficient and easy to handle sorbent material for extraction of U^VI .

N, P, and S Codoped Graphene-Like Carbon Nanosheets for Ultrafast Uranium (VI) Capture with High Capacity

The development of functional materials for the highly efficient capture of radionuclides, such as uranium from nuclear waste solutions, is an important and challenging topic. Here, few-layered N, P, and S codoped graphene-like carbon nanosheets (NPS-GLCs) that are fabricated in the 2D confined spacing of silicate RUB-15 and applied as sorbents to remove U(VI)ions from aqueous solutions are presented. The NPS-GLCs exhibit a large capacity, wide pH suitability, an ultrafast removal rate, stability at high ionic strengths, and excellent selectivity for U(VI) as compared to multiple competing metal ions. The 2D ultrathin structure of NPS-GLCs with large spacing of 1 nm not only assures the rapid mass diffusion, but also exposes a sufficient active site for the adsorption. Strong covalent bonds such as P-O-U and S-O-U are generated between the heteroatom (N, P, S) with UO2 2+ according to X-ray photoelectron spectroscopy analysis and density functional theory theoretical calculations. This work highlights the interaction mechanism of low oxidation state heteroatoms with UO2 2+, thereby shedding light on the material design of uranium immobilization in the pollution cleanup of radionuclides.

Efficient U(VI) Reduction and Sequestration by Ti2CT x MXene

Although reduction of highly mobile U(VI) to less soluble U(IV) has been long considered an effective approach to in situ environmental remediation of uranium, candidate reducing agents are largely limited to Fe-based materials and microbials. The importance of titanium-containing compounds in natural uranium ore deposits suggests a role for titanium in uranium migration. Herein, for the first time, a two-dimensional transition metal carbide, Ti₂CT _x, is shown to efficiently remove uranium via a sorption-reduction strategy. Batch experiments demonstrate that TiC₂T _x exhibits excellent U(VI) removal over a wide pH range, with an uptake capacity of 470 mg g^-1 at pH 3.0. The mechanism for U(VI) to U(IV) reduction by Ti₂CT _x was deciphered by X-ray absorption spectroscopy and diffraction and photoelectron spectroscopy. The reduced U(IV) species at low pH is identified as mononuclear with bidendate binding to the MXene substrate. At near-neutral pH, nanoparticles of the UO_{2+ x} phase adsorb to the substrate with some Ti₂CT _x transformed to amorphous TiO₂. A subsequent in-depth study suggests Ti₂CT _x materials may be potential candidates for permeable reactive barriers in the treatment of wastewaters from uranium mining. This work highlights reduction-induced immobilization of U(VI) by Ti₂CT _x MXene including a pH-dependent reduction mechanism that might promote applications of titanium-based materials in the elimination of other oxidized contaminants.

Hierarchically structured layered-double-hydroxides derived by ZIF-67 for uranium recovery from simulated seawater

Under the background of increasing and sustainable development of nuclear industry, it is significant to develop materials with high adsorption capacity and high selectivity of uranium as adsorbents. In this work, novel Mg-Co layered-double-hydroxide (LDH) with hierarchical structure was synthesized successfully via self-sacrifice template by ZIF-67. X-ray diffraction (XRD) technique, scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FT-IR), Brunauer-Emmett-Teller surface area measurement (BET) and X-ray photoelectron spectroscopy (XPS) characterization were conducted, which confirmed the specifically hollow structured material possesses high surface area and abundant mesopores that makes uranium ions diffuse into it more easily. In typical batch adsorption experiments, varieties of parameters were investigated in details. In addition, adsorption of trace concentration of uranium (ppb level) in simulated seawater was also studied. The results showed as-prepared Mg-Co LDHs are promising adsorbents for extraction of uranium from simulated seawater.

Phosphate-Functionalized Polyethylene with High Adsorption of Uranium(VI)

For uranium extraction from seawater, development of new stable and reusable sorbents with high affinity and good selectivity for U(VI) is required. Herein, a new phosphate-functionalized polyethylene (denoted PO₄/PE) was synthesized via a simple Ar-jet plasma treatment of PE in concentrated H₃PO₄ and was employed in U(VI) extraction from seawater. The prepared PO₄/PE shows superior performance in the extraction of trace U(VI) from seawater. The adsorption process followed the second-order kinetics model and the Langmuir model. The maximum adsorption capacity of PO₄/PE for U(VI) reaches 173.8 mg/g at pH 8.2 and 298 K. PO₄/PE can be effectively regenerated by 0.1 mol/L Na₂CO₃ and reused well even after eight cycles. Experimental results offer a new approach for U(VI) uptake from seawater.

Reactivity enhancement of iron sulfide nanoparticles stabilized by sodium alginate: Taking Cr (VI) removal as an example

The widespread distribution of chromium(VI) in the environment leads to groundwater contamination. The use of iron sulfide (FeS) to remove Cr(VI) has therefore been proposed. However, aggregation is one of the main problems associated with the use of FeS nanoparticles prepared by traditional methods In this study, we used sodium alginate (SA) to stabilize FeS nanoparticles (FeS-SA). SA could prevent aggregation of FeS by the concurrent electrostatic repulsion and steric hindrance. Homogeneously dispersed FeS-SA nanoparticles 100nm in diameter were observed. FeS-SA showed high efficiency in Cr(VI) removal, corresponding to an enhancement of efficiency from 65% (7.50mmol Cr(VI) per g FeS) to 100% (11.54mmol Cr per g FeS) relative to that achieved with naked FeS. Analysis of reaction products by X-ray diffraction and X-ray photoelectron spectroscopy revealed the co-existence of α-FeOOH, S₈, and Cr(OH)₃ that apparently were introduced by Fe(II), S(-II), and Cr(VI), respectively. In-depth analysis of the removal mechanism revealed that reduction and adsorption respectively account for 82% and 18% of the Cr removal. In addition, higher pH and CaCl₂ concentration resulted in lower removal efficiency. This study provides a promising application of SA in enhancing FeS reactivity for the remediation of groundwater pollution.

Hormetic effect induced by depleted uranium in zebrafish embryos

The present work studied the hormetic effect induced by uranium (U) in embryos of zebrafish (Danio rerio) using apoptosis as the biological endpoint. Hormetic effect is characterized by biphasic dose-response relationships showing a low-dose stimulation and a high-dose inhibition. Embryos were dechorionated at 4h post fertilization (hpf), and were then exposed to 10 or 100μg/l depleted uranium (DU) in uranyl acetate solutions from 5 to 6 hpf. For exposures to 10μg/l DU, the amounts of apoptotic signals in the embryos were significantly increased at 20 hpf but were significantly decreased at 24 hpf, which demonstrated the presence of U-induced hormesis. For exposures to 100μg/l DU, the amounts of apoptotic signals in the embryos were significantly increased at 20, 24 and 30 hpf. Hormetic effect was not shown but its occurrence between 30 and 48 hpf could not be ruled out. In conclusion, hormetic effect could be induced in zebrafish embryos in a concentration- and time-dependent manner.

Synthesis of activated carbon/polyaniline nanocomposites for enhanced CO2 adsorption

A new insight to investigate the potential applicability of different nanostructures of a PANI composite with activated carbon for CO₂ adsorption.

New insights into the uranium adsorption behavior of mesoporous SBA-15 silicas decorated with alkylphosphine oxide ligands

Alkylphosphine oxide functionalized mesoporous silicas were prepared by co-condensation and further addition reaction with secondary n-propylphosphine oxide and are promising candidates for the preconcentration and adsorption of uranium from acidic aqueous solutions.