Characterization of the biosorption and biodegradation properties of Ensifer adhaerens: A potential agent to remove polychlorinated biphenyls from contaminated water

Study on the mechanism and degradation behavior of Encifer adhaerens DNM-S1 capturing dimethyl phthalate

The global concern surrounding pollution caused by phthalates is escalating, with dimethyl phthalate (DMP) emerging as one of the most prevalent contaminants within the phthalates (PAEs) category. Although the biodegradation of DMP is considered both safe and efficient, its underlying degradation mechanism is not yet fully elucidated, and the degradation performance can be somewhat inconsistent. To address this issue, our study isolated a DMP-degrading bacterium (DNM-S1) from a vegetable greenhouse. The resulting data revealed that DNM-S1 exhibited a remarkable degradation performance, successfully degrading 84.98% of a 2000 mg L-1 DMP solution within 72 h. Remarkably, it achieved complete degradation of a 50 mg L-1 DMP solution within just 3 h. DMP degradation by DNM-S1 was also found to be efficient even under low-temperature conditions (10 °C). Our research further indicates that DNM-S1 is capable of capturing DMP through the ester bond in the bacterium's cell wall fatty acids, forming hydrogen bonds through hydrophobic interactions. The DMP was then transported into the DNM-S1 protoplasm using an active transport mechanism. Interestingly, the secondary metabolites of DNM-S1 contained natural carotenoids, which could potentially counteract the damaging effects of PAEs on cell membrane permeability. In summary, these findings highlight the potential of DNM-S1 in addressing PAEs pollution and provide new insights into the metabolic mechanism of PAEs degradation.

The quorum sensing SinI/R system contributes to cadmium immobilization in Ensifer adhaerens NER9 in the cadmium-contaminated solution

In this study, the cadmium (Cd)-tolerant Ensifer adhaerens strain NER9 with quorum sensing (QS) systems (responsible for N-acyl homoserine lactone (AHL) production) was characterized for QS system-mediated Cd immobilization and the underlying mechanisms involved. Whole-genome sequence analysis revealed that strain NER9 contains the QS SinI/R and TraI/R systems. Strains NER9 and the NER9∆sinI/R, NER9∆traI/R, and NER9∆sinI/R-traI/R mutants were constructed and compared for QS SinI/R and TraI/R system-mediated Cd immobilization in the solution and the mechanisms involved. After 24 h of incubation, strain NER9 significantly decreased the Cd concentration in the Cd-contaminated solution compared with the NER9∆sinI/R, NER9∆traI/R, and NER9∆sinI/R-traI/R mutants. The NER9∆sinI/R mutant had a greater impact on Cd immobilization and a lower impact on the activities of AHLs than did the NER9∆traI/R mutant. The NER9∆sinI/R mutant had significantly greater Cd concentrations and lower cell wall- and exopolysaccharide (EPS)-adsorbed Cd contents than did strain NER9. Furthermore, the NER9∆sinI/R mutant presented a decrease in the number of functional groups interacting with Cd, compared with strain NER9. These results suggested that the SinI/R system in strain NER9 contributed to Cd immobilization by mediating cell wall- and EPS-adsorption in Cd-containing solution.

Genome Analysis and Potential Ecological Functions of Members of the Genus Ensifer from Subsurface Environments and Description of Ensifer oleiphilus sp. nov

The current work deals with genomic analysis, possible ecological functions, and biotechnological potential of two bacterial strains, HO-A22T and SHC 2-14, isolated from unique subsurface environments, the Cheremukhovskoe oil field (Tatarstan, Russia) and nitrate- and radionuclide-contaminated groundwater (Tomsk region, Russia), respectively. New isolates were characterized using polyphasic taxonomy approaches and genomic analysis. The genomes of the strains HO-A22T and SHC 2-14 contain the genes involved in nitrate reduction, hydrocarbon degradation, extracellular polysaccharide synthesis, and heavy metal detoxification, confirming the potential for their application in various environmental biotechnologies. Genomic data were confirmed by cultivation studies. Both strains were found to be neutrophilic, chemoorganotrophic, facultatively anaerobic bacteria, growing at 15-33 °C and 0-1.6% NaCl (w/v). The 16S rRNA gene sequences of the strains were similar to those of the type strains of the genus Ensifer (99.0-100.0%). Nevertheless, genomic characteristics of strain HO-A22T were below the thresholds for species delineation: the calculated average nucleotide identity (ANI) values were 83.7-92.4% (<95%), and digital DNA-DNA hybridization (dDDH) values were within the range of 25.4-45.9% (<70%), which supported our conclusion that HO-A22T (=VKM B-3646T = KCTC 92427T) represented a novel species of the genus Ensifer, with the proposed name Ensifer oleiphilus sp. nov. Strain SHC 2-14 was assigned to the species 'Ensifer canadensis', which has not been validly published. This study expanded the knowledge about the phenotypic diversity among members of the genus Ensifer and its potential for the biotechnologies of oil recovery and radionuclide pollution treatment.

Chemodiversity of soil organic matters determines biodegradation of polychlorinated biphenyls by a graphene oxide-assisted bacterial agent

A promising strategy for degrading persistent organic pollutants (POPs) in soil is amendment with nanomaterial-assisted functional bacteria. However, the influence of soil organic matter chemodiversity on the performance of nanomaterial-assisted bacterial agents remains unclear. Herein, different types of soil (Mollisol soil, MS; Ultisol soil, US; and Inceptisol soil, IS) were inoculated with a graphene oxide (GO)-assisted bacterial agent (Bradyrhizobium diazoefficiens USDA 110, B. diazoefficiens USDA 110) to investigate the association between soil organic matter chemodiversity and stimulation of polychlorinated biphenyl (PCB) degradation. Results indicated that the high-aromatic solid organic matter (SOM) inhibited PCB bioavailability, and lignin-dominant dissolved organic matter (DOM) with high biotransformation potential was a favored substrate for all PCB degraders, which led to no stimulation of PCB degradation in MS. Differently, high-aliphatic SOM in US and IS promoted PCB bioavailability. The high/low biotransformation potential of multiple DOM components (e.g., lignin, condensed hydrocarbon, unsaturated hydrocarbon, etc.) in US/IS further resulted to the enhanced PCB degradation by B. diazoefficiens USDA 110 (up to 30.34%) /all PCB degraders (up to 17.65%), respectively. Overall, the category and biotransformation potential of DOM components and the aromaticity of SOM collaboratively determine the stimulation of GO-assisted bacterial agent on PCB degradation.

Differences in adsorption, transmembrane transport and degradation of pyrene and benzo[a]pyrene by Bacillus sp. strain M1

In a previous study our group identified Bacillus sp. strain M1 as an efficient decomposer of high molecular weight-polycyclic aromatic hydrocarbons (HMW-PAHs). Interestingly, its removal efficiency for benzo[a]pyrene (BaP) was nearly double that of pyrene (Pyr), which was the reverse of what is reported for most other species. Here we compared the differential steps of biosorption, transmembrane transport and biodegradation of Pyr and BaP by strain M1 in order to assist in targeted selection of dominant strains and their degradation efficiency in the remediation of these two HMW-PAHs. The overall biosorption efficiency for BaP was 19% higher than that for Pyr, and the time needed to reach BaP peak adsorption efficiency was 4 days shorter than for Pyr. Transmembrane transport of the PAHs was compared in presence of sodium azide which inhibits ATP synthesis and metabolism. This indicated that both Pyr and BaP entered the cells by the same means of passive transport. Biodegradation of Pyr and BaP did not differ in the early stage of culture, but around days 5-7, the biodegradation efficiency of BaP was significantly (30-61%) higher than that of Pyr. Key enzymes involved in these processes were identified and their activity differed, with intracellular gentisate 1,2-dioxygenase and extracellular polyphenol oxidase as likely candidates to be involved in BaP degradation, while intracellular catechol-1,2- dioxygenase and salicylate hydroxylase are more likely involved in Pyr degradation. These results provide new insights for sustainable environmental remediation of pyrene and benzo(a)pyrene by these bacteria.

Update of the list of QPS-recommended microbiological agents intentionally added to food or feed as notified to EFSA 16: suitability of taxonomic units notified to EFSA until March 2022

The qualified presumption of safety (QPS) approach was developed to provide a regularly updated generic pre-evaluation of the safety of microorganisms, intended for use in the food or feed chains, to support the work of EFSA's Scientific Panels. The QPS approach is based on an assessment of published data for each agent, with respect to its taxonomic identity, the body of relevant knowledge, safety concerns and occurrence of antimicrobial resistance. Safety concerns identified for a taxonomic unit (TU) are, where possible, confirmed at the species/strain or product level and reflected by 'qualifications'. In the period covered by this statement, no new information was found that would change the status of previously recommended QPS TUs. Of the 50 microorganisms notified to EFSA in October 2021 to March 2022 (inclusive), 41 were not evaluated: 10 filamentous fungi, 1 Enterococcus faecium, 1 Clostridium butyricum, 3 Escherichia coli and 1 Streptomyces spp. because are excluded from QPS evaluation, and 25 TUs that have already a QPS status. Nine notifications, corresponding to seven TUs were evaluated: four of these, Streptococcus salivarius, Companilactobacillus formosensis, Pseudonocardia autotrophica and Papiliotrema terrestris, being evaluated for the first time. The other three, Microbacterium foliorum, Pseudomonas fluorescens and Ensifer adhaerens were re-assessed. None of these TUs were recommended for QPS status: Ensifer adhaerens, Microbacterium foliorum, Companilactobacillus formosensis and Papiliotrema terrestris due to a limited body of knowledge, Streptococcus salivarius due to its ability to cause bacteraemia and systemic infection that results in a variety of morbidities, Pseudonocardia autotrophica due to lack of body of knowledge and uncertainty on the safety of biologically active compounds which can be produced, and Pseudomonas fluorescens due to possible safety concerns.

Biosorption of LMW PAHs on activated sludge aerobic granules under varying BOD loading rate conditions

Polycyclic aromatic hydrocarbons belong to the main priority substances for the aquatic environment. One of the emission sources of these compounds to environment is wastewater discharged from conventional wastewater treatment systems, which are not designed to cope with this type of pollution. Thus, due to the widely discussed properties of aerobic granular activated sludge in the literature - a conducted study has proven its ability to remove LMW PAHs (naphthalene (Nap), acenaphthylene (Acy), acenaphthene (Ace), fluorene (Flu), phenanthrene (Phe) and anthracene (Ant)) from wastewater by biosorption process at varying loadings of organic compounds expressed as BOD (kg/kg·d) on the activated sludge mass. The maximum biosorption of Nap was 605 µg/kg_d.m., Acy equals to 134 µg/kg_d.m., Ace equals to 355 µg/kg_d.m. Flu equals to 104 µg/kg_d.m. Phe equal to 204 µg/kg_d.m. and Ant equal to 173 µg/kg_d.m. The study showed that the BOD loading rate is one of the factors affecting the biosorption process of LMW PAHs. However, as the amount of adsorbed LMW PAHs increased, the condition of aerobic granular activated sludge deteriorated, which was evidenced by gradual increase in the values of technological parameters of activated sludge (SVI, HRT, SRT) and a smaller increase in activated sludge dry mass.

Microbial and enzymatic degradation of PCBs from e-waste-contaminated sites: a review

Electronic waste is termed as e-waste and on recycling it produces environmental pollution. Among these e-waste pollutants, polychlorinated biphenyls (PCBs) are significantly important due to ubiquitous, organic in nature and serious health and environmental hazards. PCBs are used in different electrical equipment such as in transformers and capacitors for the purposes of exchange of heat and hydraulic fluids. Bioremediation is a reassuring technology for the elimination of the PCBs from the environment. In spite of their chemical stability, there are several microbes which can bio-transform or mineralize the PCBs aerobically or anaerobically. In this review paper, our objective was to summarize the information regarding PCB-degrading enzymes and microbes. The review suggested that the most proficient PCB degraders during anaerobic condition are Dehalobacter, Dehalococcoides, and Desulfitobacterium and in aerobic condition are Burkholderia, Achromobacter, Comamonas, Ralstonia, Pseudomonas, Bacillus, and Alcaligenes etc., showing the broadest substrate among bacterial strains. Enzymes found in soil such as dehydrogenases and fluorescein diacetate (FDA) esterases have the capability to breakdown PCBs. Biphenyl upper pathway involves four enzymes: dehydrogenase (bphB), multicomponent dioxygenase (bphA, E, F, and G), second dioxygenase (bphC), hydrolase, and (bphD). Biphenyl dioxygenase is considered as the foremost enzyme used for aerobic degradation of PCBs in metabolic pathway. It has been proved that several micro-organisms are responsible for the PCB metabolization. The review provides novel strategies for e-waste-contaminated soil management.

Understanding the role of bacterial cellular adsorption, accumulation and bioavailability regulation by biosurfactant in affecting biodegradation efficacy of polybrominated diphenyl ethers

Microbiological degradation is often considered as an important strategy to reduce the risks of polybrominated diphenyl ethers (PBDEs), which are environmentally widespread and harmful to human health and wildlife. With the well-identified aerobic bacteria, i.e. B. xenovorans LB400, the biodegradation of 2,2',4,4'-tetrabrominated diphenyl ether (BDE-47) occurred efficiently in conformity to the first-order kinetics and showed the strong dependence on initial concentration of pollutant and bioavailability regulation by biosurfactant. The mild increase of initial concentration of BDE-47 would enhance biodegradation whereas the excessive increase failed due to the oxidative stress or cytotoxicity to bacteria. Rather than the bacterial extracellular adsorption that was bioactively-mediated in thermodynamics, the intracellular accumulations at different time gradients showed the negative correlation with biodegradation efficiency of BDE-47. The spontaneous biodegradation of pollutant should be sourced from the gradual reduction of intracellular accumulation. Though the improved bioavailability of BDE-47 by sucrose fatty acid ester (SFAE) hardly altered the extracellular adsorption, the bacterial intracellular accumulation was indicated to increase continuously with used amount of biosurfactant and then decrease for the cellular morphological damage, and interestingly it appeared to be temporary reservoir for prompt delivery to biodegradation in light of the opposite variation tendency with time.

Effective adsorption of nickel (II) with Ulva lactuca dried biomass: isotherms, kinetics and mechanisms

This study aimed to evaluate the Ni²⁺ ions adsorption capability of Ulva lactuca. The isotherms, kinetics and mechanisms for the adsorption of Ni²⁺ from aqueous solution by Ulva lactuca were also investigated. Influencing factors including initial pH, initial Ni²⁺ concentration, biomass, contact time were examined. The results indicate that the maximum Ni²⁺ adsorption capacity of 38.28 mg/g was obtained at pH 5, initial Ni²⁺ concentration 250 mg/L, biomass dosage 0.5 g/L and contact time 30 min. The adsorption can be well fitted with Langmuir isotherm, and the kinetics were well described by the pseudo-second-order model. The parameters of thermodynamics verified that Ni²⁺ adsorption on Ulva lactuca was a spontaneous and endothermic process. Analyses of FT-IR, SEM-EDS and XPS indicate that carboxyl and hydroxyl groups on the surface of biomass are involved in Ni²⁺ adsorption. The dried biomass of Ulva lactuca can be a cost-effective and eco-friendly adsorbent for the removal of Ni²⁺ from wastewater.

Effect of extracellular polymeric substance components on the sorption behavior of 2,2',4,4'-tetrabromodiphenyl ether to soils: Kinetics and isotherms

Microbial extracellular polymeric substances (EPS) and persistent organic pollutants (POPs) commonly exist in the soil environment. Currently, there is a knowledge gap regarding the effect of EPS on the fate of POPs in soil. In the present study, 2,2',4,4'-tetrabromodiphenyl ether (BDE-47) was used as a model compound to investigate the effects of bovine serum albumin (BSA) and sodium alginate (SA) - mimicking the main components of EPS - on sorption of POPs to soils, through batch experiments. Irrespective of the concentration of BSA: the addition of BSA did enhance the sorption capacity of BDE-47 to soils, due to generation of more sorption sites. For SA, it increased the sorption capacity of BDE-47 at low BDE-47 concentrations, while the presence of SA negatively affected sorption of BDE-47 at high BDE-47 concentrations. The partition effect dominates the sorption of BDE-47 to soils, but after adding either BSA or SA, the sorption of BDE-47 to soils is dominated by surface sorption. Film diffusion and intra-particle diffusion were also involved in the sorption process with and without BSA or SA, with the latter being the rate-limiting step. The heterogeneous surface and nonlinear sorption behavior of BDE-47 to soils increased in the presence of either BSA or SA. The FTIR spectra indicated that the aromatic CC, H-bonds and OH groups may be involved in the sorption process. Therefore, BSA enhanced the retention of BDE-47 to soil, while SA's influence on BDE-47 sorption to soil depended on the concentration of BDE-47.

Hypersensitive Response of Plasmid-Encoded AHL Synthase Gene to Lifestyle and Nutrient by Ensifer adhaerens X097

It is known that some bacteria, especially members of the family Rhizobiaceae, have multiple N-acyl homoserine lactones (AHL) synthase genes and produce multiple AHL signals. However, how bacteria selectively utilize these multiple genes and signals to cope with changing environments is poorly understood. Ensifer adhaerens is an important microorganism in terms of biotechnology, ecology and evolutionary. In this study, we investigated the AHL-based QS system of E. adhaerens X097 and its response to different lifestyles or nutrients. Draft genome sequence data indicated that X097 harbored three distinct AHL synthase genes (ensI1, 2, 3) and seven luxR homologs, which was different from other E. adhaerens strains. In vitro expression indicated that plasmid-encoded ensI1 and ensI2 directed production of multiple AHLs, while chromosome-encoded ensI3 only directed production of C14-HSL. Predicted three dimensional structure of EnsI3 was quite different from that of EnsI1 and EnsI2. X097 produced different AHL profiles in Luria-Bertani (LB) and NFB medium, under biofilm and planktonic lifestyle, respectively. Notably, expression of ensI1 and ensI2 but not ensI3 is hypersensitive to different lifestyles and nutrients. The hypersensitive response of plasmid-encoded AHL synthase genes to different culture conditions may shed a light on the phylogenetic development of AHL synthase genes in Rhizobiaceae family.

Single-Cell Real-Time Visualization and Quantification of Perylene Bioaccumulation in Microorganisms

Bioaccumulation of perylene in Escherichia coli and Staphylococcus aureus was visualized and quantified in real time with high sensitivity at high temporal resolution. For the first time, single-molecule fluorescence microscopy (SMFM) with a microfluidic flow chamber and temperature control has enabled us to record the dynamic process of perylene bioaccumulation in single bacterial cells and examine the cell-to-cell heterogeneity. Although with identical genomes, individual E. coli cells exhibited a high degree of heterogeneity in perylene accumulation dynamics, as shown by the high coefficient of variation (C.V = 1.40). This remarkable heterogeneity was exhibited only in live E. coli cells. However, the bioaccumulation of perylene in live and dead S. aureus cells showed similar patterns with a low degree of heterogeneity (C.V = 0.36). We found that the efflux systems associated with Tol C played an essential role in perylene bioaccumulation in E. coli, which caused a significantly lower accumulation and a high cell-to-cell heterogeneity. In comparison with E. coli, the Gram-positive bacteria S. aureus lacked an efficient efflux system against perylene. Therefore, perylene bioaccumulation in S. aureus was simply a passive diffusion process across the cell membrane.