Adsorptive removal of bisphenol A from aqueous solutions using phosphonated levan

Similarities and differences of nano-sized levan synthesized by Bacillus haynesii at low and high temperatures: Characterization and bioactivity

Levan is a biopolymer with many different uses. Temperature is an important parameter in biopolymer synthesis. Herein, levan production was carried out from Bacillus haynesii, a thermophilic microorganism, in the temperature range of 4 °C-95 °C. The highest levan production was measured as 10.9 g/L at 37 °C. The synthesized samples were characterized by FTIR and NMR analysis. The particle size of the levan samples varied between 153 and 824.4 nm at different temperatures. In levan samples produced at high temperatures, the water absorption capacity is higher in accordance with the particle size. Irregularities were observed in the surface pores at temperatures of 60 °C and above. The highest emulsion capacity of 83.4 % was measured in the sample synthesized at 4 °C. The antioxidant activity of all levan samples synthesized at different temperatures was measured as 84 % on average. All synthesized levan samples showed antibacterial effect on pathogenic bacteria. In addition, levan synthesized at 45 °C showed the highest antimicrobial effect on E. coli ATCC 35218 with an inhibition zone of 21.3 ± 1.82 mm. Antimicrobial activity against yeast sample C. albicans, was measured only in levan samples synthesized at 80 °C, 90 °C, 95 °C temperatures. Levan synthesized from Bacillus haynesii at low and high temperatures showed differences in characterization and bioactivity.

Effective adsorption of bisphenol A from aqueous solution using phosphoric acid-assisted hydrochar

Sycamore leaf biochar (PSAC) was prepared by a two-step phosphoric acid-assisted hydrothermal carbonization combined with a short-time activation method. The characterization results showed that the introduction of phosphoric acid molecules and thermal activation resulted in a substantial increase in the specific surface area (994.21 m2/g) and microporous capacity (0.307 cm3/g) of PSAC. The batch adsorption results showed that the adsorption process of PSAC on bisphenol A (BPA) was best described by the pseudo-second-order kinetic model and Sips isothermal model, with a maximum adsorption capacity of 247.42 mg/g. The adsorption of BPA onto PSAC was determined to be a spontaneous endothermic process. The equilibrium adsorption capacity of PSAC exhibited an upward trend with increasing initial BPA concentration and temperature while decreasing with higher adsorbent dosage and pH value. Coexisting cations and humic acids in water have little impact on the adsorption performance of PSAC for BPA. The adsorption mechanism of BPA by PSAC was mainly governed by pore filling and hydrogen bonding interactions, π-π interactions, and intraparticle diffusion. Furthermore, PSAC demonstrated good reusability by its sustained adsorption capacity of BPA, which remained at 82.6% of the initial adsorption capacity even after four adsorption-desorption cycles. These findings highlight the potential of utilizing low-cost sycamore leaf biochar as an effective adsorbent for the removal of the endocrine disruptor BPA.

Review on impacts of micro- and nano-plastic on aquatic ecosystems and mitigation strategies

The rapid proliferation of microplastics (MPs) and nanoplastics (NPs) in our environment presents a formidable hazard to both biotic and abiotic components. These pollutants originate from various sources, including commercial production and the breakdown of larger plastic particles. Widespread contamination of the human body, agroecosystems, and animals occurs through ingestion, entry into the food chain, and inhalation. Consequently, the imperative to devise innovative methods for MPs and NPs remediation has become increasingly apparent. This review explores the current landscape of strategies proposed to mitigate the escalating threats associated with plastic waste. Among the array of methods in use, microbial remediation emerges as a promising avenue for the decomposition and reclamation of MPs and NPs. In response to the growing concern, numerous nations have already implemented or are in the process of adopting regulations to curtail MPs and NPs in aquatic habitats. This paper aims to address this gap by delving into the environmental fate, behaviour, transport, ecotoxicity, and management of MPs and NPs particles within the context of nanoscience, microbial ecology, and remediation technologies. Key findings of this review encompass the intricate interdependencies between MPs and NPs and their ecosystems. The ecological impact, from fate to ecotoxicity, is scrutinized in light of the burgeoning environmental imperative. As a result, this review not only provides an encompassing understanding of the ecological ramifications of MPs and NPs but also highlights the pressing need for further research, innovation, and informed interventions.

An integrated approach to remove endocrine-disrupting chemicals bisphenol and its analogues from the aqueous environment: a review

Bisphenol A (BPA) is a well-known endocrine-disrupting chemical (EDC) used as a plastic enhancer in producing polycarbonate resins to manufacture hard plastics. Due to strict limitations on the manufacturing and utilization of BPA, several bisphenol substitutes, bisphenol F (BPF), bisphenol S (BPS), and bisphenol AF (BPAF), have been developed to replace it in various applications. Because of their widespread use in food containers, infant bottles, and reusable water bottles, bisphenols (BPs) have been identified in different environmental circumstances, including drinking water, seawater, industrial effluent, and endocrine systems such as human blood, urine, and breast milk. However, locating and analyzing them in different conditions has proven to be challenging. Therefore, there is a need to reduce the prevalence of BPs in the environment. The significance of advanced treatment options for treating and eliminating BPA and its alternatives from water bodies are reviewed. Also, the research gaps and future scopes are discussed in this review article. According to the literature survey, adsorption and photocatalytic degradation provide synergistic benefits for environmental challenges because of their substantial adsorption Q5 capacity, high oxidation capability, and low cost compared to alternative individual treatment options.

Thermal and bisphenol-A adsorption properties of a zinc ferrite/β-cyclodextrin polymer nanocomposite

The present study investigated the use of a nanocomposite, produced by reinforcing nanosize zinc ferrite (ZnFe₂O₄) in a porous β-CD based polymeric matrix (β-CD-E-T/ZnFe₂O₄), for the removal of Bisphenol A (BPA) from aqueous solutions via adsorption. The thermal stability of the β-CD-based polymer and β-CD-E-T/ZnFe₂O₄ nanocomposite were investigated using simultaneous thermal analysis at four heating rates. Non-isothermal isoconversion methods were employed to study the thermal degradation kinetics of the β-CD based polymer before and after ZnFe₂O₄ nano-filling. The results showed that ZnFe₂O₄ nano-reinforcement increased the activation energy barrier for the thermal degradation of the β-CD-based polymeric matrix. Adsorption experiments showed that the β-CD-E-T/ZnFe₂O₄ nanocomposite exhibited very high BPA adsorption within 5 minutes. Isotherm, kinetics, and thermodynamic investigations revealed that the adsorption of BPA was via multilayer adsorption on a heterogeneous β-CD-E-T/ZnFe₂O₄ surface. The thermodynamic studies indicated that BPA adsorption on β-CD-E-T/ZnFe₂O₄ was spontaneous and exothermic. Overall, the β-CD-E-T/ZnFe₂O₄ nanocomposite showed less thermal degradation and high efficiency for removing BPA from contaminated water, indicating its potential as a promising material for wastewater treatment applications.

Spinel cobalt ferrite-based porous activated carbon in conjunction with UV light irradiation for boosting peroxymonosulfate oxidation of bisphenol A

Developing heterogeneous catalysts with high performance for peroxymonosulfate (PMS) activation to decontaminate organic pollutants from wastewater is of prominent importance. In this study, spinel cobalt ferrite (CoFe₂O₄) materials were coated on the surface of powdered activated carbon (CoFe₂O₄@PAC) via the facile co-precipitation method. The high specific surface area of PAC was beneficial for the adsorption of both bisphenol A (BP-A) and PMS molecules. The CoFe₂O₄@PAC-mediated PMS activation process under UV light could effectively eliminate 99.4% of the BP-A within 60 min of reaction. A significant synergy effect was attained between CoFe₂O₄ and PAC towards PMS activation and subsequent elimination of BP-A. Comparative tests demonstrated that the heterogeneous CoFe₂O₄@PAC catalyst had a better degradation performance in comparison with its components and homogeneous catalysts (Fe, Co, and, Fe + Co ions). The formed by-products and intermediates during BP-A decontamination were evaluated using LC/MS analysis, and then a possible degradation pathway was proposed. Moreover, the prepared catalyst exhibited excellent performance in recyclability with slight leaching amounts of Co and Fe ions. A TOC conversion of 38% was obtained after five consecutive reaction cycles. It can be concluded that the PMS photo-activation process via the CoFe₂O₄@PAC catalyst can be utilized as an effective and promising method for the degradation of organic contaminants from polluted-water resources.

Exploring the potential of Halomonas levan and its derivatives as active ingredients in cosmeceutical and skin regenerating formulations

Demand on natural products that contain biological ingredients mimicking growth factors and cytokines made natural polysaccharides popular in pharmaceutical and cosmetic industries. Levan is the β-(2-6) linked, nontoxic, biocompatible, water-soluble, film former fructan polymer that has diverse applications in pharmacy and cosmeceutical industries with its moisturizing, whitening, anti-irritant, anti-aging and slimming activities. Driven by the limited reports on few structurally similar levan polymers, this study presents the first systematic investigation on the effects of structurally different extremophilic Halomonas levan polysaccharides on human skin epidermis cells. In-vitro experiments with microbially produced linear Halomonas levan (HL), its hydrolyzed, (hHL) and sulfonated (ShHL) derivatives as well as enzymatically produced branched levan (EL) revealed increased keratinocyte and fibroblast proliferation (113-118 %), improved skin barrier function through induced expressions of involucrin (2.0 and 6.43 fold changes for HL and EL) and filaggrin (1.74 and 3.89 fold changes for hHL and ShHL) genes and increased type I collagen (2.63 for ShHL) and hyaluronan synthase 3 (1.41 for HL) gene expressions together with fast wound healing ability within 24 h (100 %, HL) on 2D wound models clearly showed that HL and its derivatives have high potential to be used as natural active ingredients in cosmeceutical and skin regenerating formulations.

UV and Chemically Induced Halomonas smyrnensis Mutants for Enhanced Levan Productivity

Halomonas smyrnensis AAD6^T is a moderately halophilic bacterium proven to be a powerful biotechnological tool with its ability to accumulate valuable biopolymers such as levan and poly(3-hydroxybutyrate) (PHB). Levan is a fructose homopolymer with β-2,6 fructofuranosidic linkages on the polymer backbone, and its distinctive applications in various industries such as food, pharmaceutical, medical, and chemical have been well-defined. On the other hand, PHB is a promising raw material to produce biodegradable plastics. Although it was shown in our previous studies that H. smyrnensis AAD6^T exhibits one of the highest conversion yields of sucrose to levan reported to date, novel strategies are required to overcome high costs of levan production. In this study, we aimed at increasing levan productivity of H. smyrnensis AAD6^T cultures using random mutagenesis techniques combined (i.e., ethyl methanesulfate treatment and/or ultraviolet irradiation). After several consecutive treatments, mutant strains BAE2, BAE5 and BAE6 were selected as efficient levan producers, as BAE2 standing out as the most efficient one not only in sucrose utilization and levan production rates, but also in final PHB concentrations. The mutants' whole genome sequences were analysed to determine the mutations occurred. Several mutations in genes related to central carbon metabolism and osmoregulation were found. Our results suggest that random mutagenesis can be a facile and efficient strategy to enhance the performance of extremophiles in adverse conditions.

Synthesis of Metal–Organic Frameworks Quantum Dots Composites as Sensors for Endocrine-Disrupting Chemicals

Hazardous chemical compounds such as endocrine-disrupting chemicals (EDCs) are widespread and part of the materials we use daily. Among these compounds, bisphenol A (BPA) is the most common endocrine-disrupting chemical and is prevalent due to the chemical raw materials used to manufacture thermoplastic polymers, rigid foams, and industrial coatings. General exposure to endocrine-disrupting chemicals constitutes a serious health hazard, especially to reproductive systems, and can lead to transgenerational diseases in adults due to exposure to these chemicals over several years. Thus, it is necessary to develop sensors for early detection of endocrine-disrupting chemicals. In recent years, the use of metal–organic frameworks (MOFs) as sensors for EDCs has been explored due to their distinctive characteristics, such as wide surface area, outstanding chemical fastness, structural tuneability, gas storage, molecular separation, proton conductivity, and catalyst activity, among others which can be modified to sense hazardous environmental pollutants such as EDCs. In order to improve the versatility of MOFs as sensors, semiconductor quantum dots have been introduced into the MOF pores to form metal–organic frameworks/quantum dots composites. These composites possess a large optical absorption coefficient, low toxicity, direct bandgap, formidable sensing capacity, high resistance to change under light and tunable visual qualities by varying the size and compositions, which make them useful for applications as sensors for probing of dangerous and risky environmental contaminants such as EDCs and more. In this review, we explore various synthetic strategies of (MOFs), quantum dots (QDs), and metal–organic framework quantum dots composites (MOFs@QDs) as efficient compounds for the sensing of ecological pollutants, contaminants, and toxicants such as EDCs. We also summarize various compounds or materials used in the detection of BPA as well as the sensing ability and capability of MOFs, QDs, and MOFs@QDs composites that can be used as sensors for EDCs and BPA.

Graphene oxide functionalized with cobalt ferrites applied to the removal of bisphenol A: ionic study, reuse capacity and desorption kinetics

A new adsorbent material based on graphene oxide (GO) functionalized with magnetic cobalt ferrite nanoparticles (γCoFe₂O₄) was synthesized via ultrasonication to remove the endocrine-disrupting-chemical bisphenol A (BPA) from aqueous solutions. The synthesized material (GO-γCoFe₂O₄) was characterized by TEM, SEM, DRX and FTIR analysis. Magnetization measures proved that the adsorbent had superparamagnetic characteristics that facilitated its separation from the aqueous solution. The maximum adsorption capacity obtained was 30 mg g^-1 with adsorbent concentration of 1 g L^-1, temperature of 55°C and natural pH of the solution. The experimental data were better adjusted to the kinetic models of pseudo-second-order and Langmuir isotherm. The thermodynamic parameters showed that the BPA adsorption on GO-γCoFe₂O₄ was spontaneous, exothermic and thermodynamically favourable. Desorption kinetics was performed using 50% ethanol as solvent, resulting in an equilibrium time of 4 h with better adjustment to the pseudo-second order kinetic model. The adsorbent showed a high regeneration capacity maintaining adsorptive capacity above 75% after 6 cycles of reuse.

Synthesis of new composite based on TiO2 immobilized in glass fibers for photo-catalytic degradation of chlorobenzene in aqueous solutions

In this study photo-catalytic degradation of chlorobenzene from aqueous solutions using CQD decorated Fe-doped TiO₂ immobilized in Glass Fibers (GF) was investigated. Characteristics of the synthesized photo-catalyst were determined by EF-SEM, EDX, BET, XRD, FTIR, and DRS analysis. Additionally, DRS analysis demonstrated adding CQD to the TiO₂-Fe reduced its band gap energy from 2.96 eV to 2.91eV, while that was 3.10 eV for undoped TiO₂. Among that three photo-catalysts, GF/CQD_(4.5 wt%) decorated Fe-TiO₂ composite had performance nearly 100.0%, when pH was 5 and low concentration of chlorobenzene. In addition, GF/CQD_(4.5 wt%) decorated Fe-TiO₂ composite show it could be well applied for five times and with a little reduction on the performance. Also, no detectable Fe found to be released from the composite. Minimum inhibitory concentration (MIC) for E. coli bacteria was 12.2 mg L^-1 of chlorobenzene residual. Our findings show the catalyst was successful for chlorobenzene removal in the wastewater effluent. In conclusion, present hybrid composite could successfully and safely remove chlorobenzene from synthetic aqueous solution.

Application of activated carbon functionalized with graphene oxide for efficient removal of COVID-19 treatment-related pharmaceuticals from water

Currently, the COVID-19 pandemic has been increasing the consumption of some drugs, such as chloroquine (CQN) and dipyrone (DIP), which are continuously discharged into water resources through domestic sewage treatment systems. The presence of these drugs in water bodies is worrisome due to their high toxicity, which makes crucial their monitoring and removal, especially by means of advanced technologies. Given this scenario, a new adsorbent material was synthesized through the combination of babassu coconut activated carbon and graphene oxide (GAC-GO). This study was evaluated in batch adsorption processes, aiming at the treatment of water contaminated with CQN and DIP. Characterization analyzes using physicochemical and spectroscopic techniques indicated that the GAC-GO functionalization was successfully performed. The equilibrium time of the adsorption process was 18 and 12 h for CQN and DIP, respectively. Kinetic and isothermal data better fitted to pseudo-second-order and Langmuir models for both drugs. Thermodynamic parameters showed that the process is endothermic and the maximum adsorption capacities of CQN and DIP were 37.65 and 62.43 mg g-1, respectively, both at 318 K. The study of the effect of ionic strength, which simulates a real effluent, demonstrated that the synthesized adsorbent has potential application for the treatment of effluents. Furthermore, satisfactory removal rates were verified for the removal of other contaminants in both simple solutions and synthetic mixtures, evidencing the versatile profile of the adsorbent.

Bisfenol A adsorption using a low-cost adsorbent prepared from residues of babassu coconut peels

Nowadays, the occurrence of microcontaminants in water resources has become a worldwide concern. Among them, it can be mentioned Bisphenol A, a substance widely used in the chemical composition of plastic such as manufacture of packages, bottles, toiletries, among others. Its use may cause adverse effects on human health and the environment. Thus, a treatment is necessary to remove this compound and adsorption is an interesting alternative due to its low cost, operation and high efficiency. The objective of the present study was to evaluate the adsorption capacity of bisphenol in babassu activated carbon. The obtained results were satisfactory and the best experimental conditions were at 318 K temperature, 1 g L^-1 adsorbent concentration and 720 min equilibrium time, resulting in the maximum adsorptive capacity of 49.61 mg g^-1. The experimental data fit best with the pseudo-second order and Langmuir models for the kinetic and equilibrium studies, respectively. Thermodynamic parameters indicated endothermic, spontaneous and reversible process. The main adsorption mechanisms were hydrogen bonds and π-π interactions. In addition, the material regeneration study allowed to verify its possibility of reuse. Therefore, it was noticed that babassu activated carbon has high potential applicability in the treatment of contaminated water.

Photo-catalytic degradation of bisphenol-a from aqueous solutions using GF/Fe-TiO2-CQD hybrid composite

In this photocatalytic study, removal of bisphenol-A from aqueous solution was studied using the GF/Fe-TiO2-CQD composite. Due to its health and environmental effects, this compound should be disposed of sources that are mainly industrial wastewater. The phis-chemical properties of the composite were determined by traditional analyzes of EF-SEM, EDX, BET, XRD, FTIR and DRS. In this study, different ratios of CQD in the composite (1.5, 4.5 and 7.5 wt%), pH, and bisphenol-A concentration as variable parameters were investigated. All analyzes, EF-SEM, EDX, BET, XRD, FTIR, show that the GF/Fe-TiO2-CQD composite is well coated on glass fibers (GF) and all the elements in the catalyst are present. On the other hand, DRS analysis showed that CQD reduces the band gap of Fe-TiO2 from 2.96 eV to 2.91 eV, it was 3.10 eV for TiO2. Among different catalysts, GF/Fe-TiO2-CQD4.5wt% has the best performance. The results showed that for GF/Fe-TiO2-CQD4.5wt%, optimum for the process was at pH = 6 in low concentration of bisphenol-A. The first order model for the photocatalytic degradation process were well studied. In addition, GF/Fe-TiO2-CQD4.5wt% showed that it can be used many times with a minimal reduction in performance. As a result, the GF/Fe-TiO2-CQD4.5wt% composite can successfully remove bisphenol-A form in synthetic aqueous solution. However, it is necessary to further studies to applied that for real water source in water and wastewater treatment plants.

Synergistic mediation of metallic bismuth and oxygen vacancy in Bi/Bi2WO6-x to promote 1O2 production for the photodegradation of bisphenol A and its analogues in water matrix

Bi/Bi₂WO_6-x heterostructures has been successfully prepared by a facile one-step hydrothermal method. By maneuvering reaction time and Bi/W molar ratio of the precursors, we have been able to selectively introduce oxygen vacancy and metallic Bi into Bi₂WO₆ nanostructures. The obtained Bi/Bi₂WO_6-x heterostructures with more oxygen vacancy and moderate metallic Bi exhibit significantly improved photocatalytic activity for the photodegradation of bisphenol A (BPA) and its analogues due to its great ability for the generation of singlet oxygen (¹O₂), which has proven to work as the main reactive oxygen species during photocatalysis. It is also found the ¹O₂ concentration is highly depended on and modulated by the content of oxygen vacancy and metallic bismuth. Besides, we also demonstrate that the obtained Bi/Bi₂WO_6-x products display efficient photocatalytic performance toward BPA derivatives degradation and enhanced stability to resist the interferences in the water matrix.

Conversion of tannery solid waste to an adsorbent for high-efficiency dye removal from tannery wastewater: A road to circular utilization

The high value-added use of tannery solid waste and elimination of tannery liquid waste in the leather-making industry have attracted widespread attention. In this study, a MgO-doped biochar (MgO/BC) adsorbent was successfully prepared by utilizing tannery solid waste (i.e., non-tanned hide wastes) as the biomass material for dye removal from tannery wastewater. Characterization results indicated that MgO was uniformly embedded into the porous BC structure. The adsorption capacity of acid orange II by MgO/BC reached up to 448.4 mg g^-1, which drastically exceeded the pure BC and other reported adsorbents. The adsorption behavior of acid orange II by MgO/BC matched nicely with Langmuir isotherm and pseudo-second-order kinetic model. This satisfactory adsorption capacity of MgO/BC for acid orange II was mainly due to the large specific surface area and the enhanced electrostatic interaction. According to the BET, zeta potential and XPS analysis, the possible mechanism towards acid orange II removal was attributed to the pore filling, surface complexation, electrostatic attraction and π-π interaction. In addition, MgO/BC showed the efficient removal towards anionic dyes from actual tannery wastewater. This work could provide guidance for the value-added utilization of tannery solid waste and a practical way to remove dyes from tannery wastewater.

Microbial remediation of micro-nano plastics: Current knowledge and future trends

An alarming rise of micro-nano plastics (MNPs) in environment is currently causing the biggest threat to biotic and abiotic components around the globe. These pollutants, apart from being formed through fragmentation of larger plastic pieces and are also manufactured for commercial usage. MNPs enter agro-ecosystem, wildlife, and human body through the food chain, ingestion or through inhalation, causing blockage in the blood-brain barrier, lower fertility, and behavioural abnormalities among other problems. Hence, it becomes essential to develop novel procedures for remediation of MNPs. Among the numerous existing methods, microbial remediation promises to degrade/recover MNPs via a green route. Since microbial remediation processes mostly depend upon biotic and abiotic factors such as (temperature, pH, oxidative stress, etc.), it becomes easy to influence changes in the plastic pollutants. Hence, with the help of recent technologies, a complete degradation/removal of MNPs can be expected by utilizing the respective carbon content as energy sources for growth of microorganisms. In this review, considering the urgent environmental need, the impact of micro-nano plastics on ecosystem along with its corresponding degradation mechanisms has been brought out. Also, importance of the various recent research approaches in MNPs remediation is highlighted. Finally, the role of enzyme and membrane technology, nanoparticle technology, and metagenomics in remediation of MNPs are discussed for the first time in detail to bring out a novel remedy for the environment.

One-pot fabrication of antibacterial β-cyclodextrin-based nanoparticles and their superfast, broad-spectrum adsorption towards pollutants

The current water treatment technology is still based on low energy efficient processes due to the complex composition of wastewater. To achieve high energy efficiency, many micro-porous materials with complex functional groups have been fabricated because of their high pollutant adsorption capabilities. In this work, antibacterial β-cyclodextrin-based nanoparticles (E-β-CDN) were prepared via one-pot method to explore their adsorption performance to pollutants in wastewater. The resulting nanoparticles exhibited superfast adsorption kinetics to pollutants with removal efficiency of over 95% within 10 s. The nanoparticles also presented broad-spectrum adsorption to organic pollutants and heavy metal ions, and their maximum adsorption capacity was 3289.6 mg g^-1 towards methyl orange (MO) and 970.8 mg g^-1 towards Pb(II), much higher than that of many other adsorbents. Easy cyclic adsorption-desorption was another distinguishing feature of the nanoparticles, whose removal efficiency to these pollutants hardly varied after 10 cycles of regeneration. Interestingly, the resulting nanoparticles showed prominent antibacterial activity of 99.99% bacterial inhibitive rate against both gram-negative bacteria Escherichia coli (E. coli) and gram-positive bacteria Staphylococcus aureus (S. aureus). These results suggest that the resulting nanoparticles have great potential in the purification of the wastewater.

Recent development in the application of immobilized oxidative enzymes for bioremediation of hazardous micropollutants - A review

During the past several years, abundant progresses has been made in the development of immobilized oxidative enzymes with focus on finding new support materials, improving the immobilization methods and their applications. Nowadays, immobilized oxidative enzymes are broadly accepted as a green way to face the challenge of high amounts of micropollutants in nature. Among all oxidative enzymes, laccases and horseradish peroxidase were used frequently in recent years as they are general oxidative enzymes with ability to oxidize various types of compounds. Immobilized laccase or horseradish peroxidase are showed better stability, and reusability as well as easy separation from reaction mixture that make them more favorable and economic in compared to free enzymes. However, additional improvements are still essential such as: development of the new materials for immobilization with higher capacity, easy preparation, and cheaper price. Moreover, immobilization methods are still need improving to become more efficient and avoid enzyme wasting during immobilization and enzyme leakage through working cycles.

Adsorptive removal of endocrine disrupting compounds from aqueous solutions using magnetic multi-wall carbon nanotubes modified with chitosan biopolymer based on response surface methodology: Functionalization, kinetics, and isotherms studies

Recently, the presence of endocrine disrupting compounds in the environment has emerged as a global and ubiquitous problem. In this study, a novel synthesis of magnetically carbon nanotube modified with biological polymeric was successfully prepared. The effect of different parameters on the Bisphenol A (BPA) adsorption was studied. A prediction model for BPA adsorption was extended based on the Central Composite Design. Also, the prepared biopolymeric nanotubes were characterized by FT-IR, XRD, TEM, FE-SEM. The surface morphology of nanocomposite was observed, increased carbon nano tube size, and the levels after surface deposition were completely covered by chitosan proteins. The results of our experiments showed that optimum adsorption conditions was achieved at t = 76 min, BPA concentration 6.5 mg/L, adsorbent dosage 1 g/L and pH = 6.2.The data obtained in this study followed the Langmuir isotherm model and the pseudo-second order model. The maximum monolayer adsorption capacity of nanocomposite for BPA was 46.2 mg/g at 20 °C. This study showed that the adsorption of BPA onto nanocomposite was spontaneous and thermodynamically desirable.

Enhancement of cadmium removal by oxygen-doped carbon nitride with molybdenum and sulphur hybridization

Graphitic carbon nitride, as a popular material in the field of environmental remediation, still suffers from unsatisfactory performance for heavy metals adsorption owing to lack of specific adsorption sites. In this study, molybdenum (Mo) and sulphur (S) were simultaneously introduced onto the surface of oxygen-doped graphitic carbon nitride (OCN) for the enhancement of Cd²⁺ adsorption. The synthesized MOS/OCN-1 exhibited substantially increased maximum adsorption capacity of 293.8 mg/g, calculated from Sips isotherm model, which was 8.7 times higher than that for pristine OCN (33.9 mg/g). The adsorption efficiency of MOS/OCN-1 was >94% even under high concentration of coexisting ions (i.e., Ca²⁺, Mg²⁺ and Zn²⁺). MoO₃ and MoS₂ on the surface of OCN were proven to interact with Cd²⁺ by forming CdMoO₄ and CdS species. OCN provided a stable matrix with a large surface area making more active sites exposed, which greatly facilitated Mo(IV) oxidation and Cd²⁺ precipitation. Our findings revealed that as well as the well-known Cd-S interaction, Mo atoms in the hybrid composites also played an important role in Cd²⁺ removal, which opened up the application possibility of OCN with Mo and S hybridization for in-situ Cd²⁺ remediation.