A critical review on VOCs adsorption by different porous materials: Species, mechanisms and modification methods

Hierarchical porous carbon nanofibrous membranes with elaborated chemical surfaces for efficient adsorptive removal of volatile organic compounds from air

Volatile organic compounds (VOCs) in the air pose great health risks to humans and the environment. Adsorptive separation technology has proven effective in mitigating VOC pollution, with the adsorbent being the critical component. Therefore, the development of highly efficient adsorbent materials is crucial. Carbon nanofibers, known for their physical-chemical stability and rapid adsorption kinetics, are promising candidates for removing VOCs from the air. However, the relatively simple porous structures and inert surface chemical properties of traditional carbon nanofibers present challenges in further enhancing their application performance further. Herein, a hierarchical porous carbon nanofibrous membrane was prepared using electrospinning technology and a one-step carbonization & activation method. Phenolic resin and polyacrylonitrile were used as co-precursors, with silica nanoparticles serving as the dopant. The resulting membrane exhibited a specific surface area of up to 1560.83 m2/g and surfaces rich in functional O-/N- groups. With a synergistic effect of developed micro- and meso-pores and active chemical surfaces, the carbon nanofibrous membrane demonstrated excellent adsorption separation performance for various VOCs, with comparable adsorption capacities and fast kinetics. Moreover, the membrane displayed remarkable reusability and dynamic adsorption performance for different VOCs, indicating its potential for practical applications.

Agri-food waste biosorbents for volatile organic compounds removal from air and industrial gases - A review

Approximately 1.3 billion metric tons of agricultural and food waste is produced annually, highlighting the need for appropriate processing and management strategies. This paper provides an exhaustive overview of the utilization of agri-food waste as a biosorbents for the elimination of volatile organic compounds (VOCs) from gaseous streams. The review paper underscores the critical role of waste management in the context of a circular economy, wherein waste is not viewed as a final product, but rather as a valuable resource for innovative processes. This perspective is consistent with the principles of resource efficiency and sustainability. Various types of waste have been described as effective biosorbents, and methods for biosorbents preparation have been discussed, including thermal treatment, surface activation, and doping with nitrogen, phosphorus, and sulfur atoms. This review further investigates the applications of these biosorbents in adsorbing VOCs from gaseous streams and elucidates the primary mechanisms governing the adsorption process. Additionally, this study sheds light on methods of biosorbents regeneration, which is a key aspect of practical applications. The paper concludes with a critical commentary and discussion of future perspectives in this field, emphasizing the need for more research and innovation in waste management to fully realize the potential of a circular economy. This review serves as a valuable resource for researchers and practitioners interested in the potential use of agri-food waste biosorbents for VOCs removal, marking a significant first step toward considering these aspects together.

Magnetically recoverable Fe3O4@SiO2@SBA-3@2-ATP-Cu: an improved catalyst for the synthesis of 5-substituted 1H-tetrazoles

Functionalization of Fe3O4@SiO2@SBA-3 with double-charged 3-chloropropyltrimethoxysilane (CPTMS) and 2-aminophenol, followed by mechanical mixing of the solid product with copper(i) chloride produces a new, greener and efficient Fe3O4@SiO2@SBA-3@2-ATP-Cu catalyst for the synthesis of 5-substituted 1H-tetrazoles. XRD, SEM, atomic absorption, TGA, N2 adsorption-desorption, and VSM analyses were performed for the characterization of the Fe3O4@SiO2@SBA-3@2-ATP-Cu structure. Nitrogen adsorption-desorption analysis revealed that Fe3O4@SiO2@SBA-3@2-ATP-Cu has a surface area of 242 m2 g-1 and a total pore volume of 55.72 cm3 g-1. In synthesizing 5-substituted 1H-tetrazoles, Fe3O4@SiO2@SBA-3@2-ATP-Cu shows superior yields in short reaction times at 120 °C. This catalyst also showed high thermal stability and recyclability at least for 4 runs without apparent loss of efficiency.

Resistive Gas Sensors Based on 2D TMDs and MXenes

ConspectusGas sensors are used in various applications to sense toxic gases, mainly for enhanced safety. Resistive sensors are particularly popular owing to their ability to detect trace amounts of gases, high stability, fast response times, and affordability. Semiconducting metal oxides are commonly employed in the fabrication of resistive gas sensors. However, these sensors often require high working temperatures, bringing about increased energy consumption and reduced selectivity. Furthermore, they do not have enough flexibility, and their performance is significantly decreased under bending, stretching, or twisting. To address these challenges, alternative materials capable of operating at lower temperatures with high flexibility are needed. Two-dimensional (2D) materials such as MXenes and transition-metal dichalcogenides (TMDs) offer high surface area and conductivity owing to their unique 2D structure, making them promising candidates for realization of resistive gas sensors. Nevertheless, their sensing performance in pristine form is typically weak and unacceptable, particularly in terms of response, selectivity, and recovery time (trec). To overcome these drawbacks, several strategies can be employed to enhance their sensing properties. Noble-metal decoration such as (Au, Pt, Pd, Rh, Ag) is a highly promising method, in which the catalytic effects of noble metals as well as formation of potential barriers with MXenes or TMDs eventually contribute to boosted response. Additionally, bimetallic noble metals such as Pt-Pd and Au/Pd with their synergistic properties can further improve sensor performance. Ion implantation is another feasible approach, involving doping of sensing materials with the desired concentration of dopants through control over the energy and dosage of the irradiation ions as well as creation of structural defects such as oxygen vacancies through high-energy ion-beam irradiation, contributing to enhanced sensing capabilities. The formation of core-shell structures is also effective, creating numerous interfaces between core and shell materials that optimize the sensing characteristics. However, the shell thickness needs to be carefully optimized to achieve the best sensing output. To reduce energy consumption, sensors can operate in a self-heating condition where an external voltage is applied to the electrodes, significantly lowering the power requirements. This enables sensors to function in energy-constrained environments, such as remote or low-energy areas. An important advantage of 2D MXenes and TMDs is their high mechanical flexibility. Unlike semiconducting metal oxides that lack mechanical flexibility, MXenes and TMDs can maintain their sensing performance even when integrated onto flexible substrates and subjected to bending, tilting, or stretching. This flexibility makes them ideal for fabricating flexible and portable gas sensors that rigid sensors cannot achieve.

Naphthalimide Based Fluorophore for the Detection of Hazardous Volatile Organic Compounds (VOCs)

The naphthalimide molecule (NAP) was successfully synthesized and characterized by spectroscopy techniques. The NAP probe was exposed to a solvatochromic and aggregation-induced emission (AIE) probe using UV-visible and PL spectroscopy. In this case, the increased polarity of the solvent shows that it is red-shifted. The probe emission, a sky blue to yellow-green color at hexane to DCM, exhibited an excellent quantum yield. Meanwhile, the high-polar solvents of DMF and DMSO had poor quantum yields. This probe NAP showed the aggregation-induced emission property dramatically enhanced the emissions (at 540 nm) from fw = 80-90%. NAP was conducted with two polar solvent vapors in hexane and chloroform to investigate VOCs in a further solid-state study. A real-life test paper kit NAP probe was prepared and investigated VOCs detection against hexane and chloroform. When exposed to hexane vapors, the NAP probe test kit showed sky blue emission under UV light, which returned to greenish emission upon exposure to chloroform. Therefore, the results show that this NAP probe can be used for gas leak detection applications.

Synergistic energy-efficient capture of VOCs and metal-free catalytic conversion using magneto-inductive Guefoams: Proof-of-concept in n-hexane-enriched nitrogen streams

Addressing contemporary environmental and health concerns requires reducing pollutant emissions and converting them into less harmful or valuable compounds within the framework of the circular economy. Guefoam materials offer a promising solution by enabling the capture and pre-concentration of volatile organic compounds (VOCs), while facilitating the structuring of active phases for heterogeneous catalytic conversions. This study demonstrates the benefits of merging two newly designed electromagnetic induction-assisted ceramic matrix Guefoams into a portable integrated unit, synergizing the pre-concentration and chemical transformation of n-hexane, a VOC with special challenges. One Guefoam serves as an adsorbent, whereas the other plays a catalytic role. These Guefoams host guest phases, which consist of composite materials combining a steel core with magneto-inductive properties encased in a highly porous carbonaceous layer. This carbonaceous material undertakes a dual mission: adsorbing n-hexane from a nitrogen stream within the adsorptive Guefoam and, upon phosphorus doping in the catalytic Guefoam, orchestrating the metal-free selective dehydroaromatization of n-hexane into benzene. The design and integration of these novel Guefoam materials into a unified functional entity prove highly effective in pre-concentrating (enrichment factors up to 275) and catalyzing n-hexane with up to 84 % conversion and 94 % benzene selectivity while remaining energy-efficient and environmentally sustainable.

Unveiling the Role of Hydrophobicity on Multilayer Carbon Nanosheets Enriched in sp2-Carbon for Toluene Adsorption under Humid Conditions

Carbon materials are regarded as a promising adsorbent for the adsorption of volatile organic compounds (VOCs). However, their adsorption behaviors are usually compromised at ambient conditions, attributed to the competitive VOCs adsorption with water vapor. In this study, we demonstrated that the selectivity for toluene than water of carbon can be effectively enhanced by introducing more sp2-carbon with two-dimensional nanosheets stacked. The multilayer carbon nanosheets enriched with sp2-carbon (CNS-MCA) exhibit a 151° H2O-contact angle, indicating hydrophobicity. Dynamic adsorption behaviors revealed that CNS-MCA retain 71% of their toluene adsorption capacity (91 mg/g) even at 60% relative humidity. Density functional theory (DFT) calculations, static adsorption studies, in situ Raman spectroscopy, and time-resolved in situ nuclear magnetic resonance (NMR) spectroscopy collectively indicate that toluene exhibits enhanced adsorption and selectivity due to π-π* interactions between its aromatic rings and the sp2-carbon. Conversely, water adsorption is attenuated, attributed to the reduced availability of surface-exposed hydrogen bonds associated with sp2-carbon and the inherent hydrophobic nature of multilayer graphene. This study extends a novel solution for the enhancement of VOCs adsorption under humid conditions.

Carbon based nanocomposites, surface functionalization as a promising material for VOCs (volatile organic compounds) treatment

Urban residential and industrial growth development affects sustainable and healthful indoor environments. Environmental issues are a global problem. The deterioration of indoor air quality has prompted the creation of several air cleansing techniques. This review explains how carbon-based materials have influenced the development of air purification systems using photocatalysis. These carbon-based materials offer unique properties and advantages in VOC removal processes. Biochar, produced from biomass pyrolysis, provides an environmentally sustainable solution with its porous structure and carbon-rich composition. Carbon quantum dots, with their quantum confinement effects and tunable surface properties, show promise in VOC sensing and removal applications. Polymers incorporating reduced graphene oxide demonstrate enhanced adsorption capabilities owing to the synergistic effects of graphene and polymer matrices. Activated carbon fibers, characterized by their high aspect ratio and interconnected porosity, provide efficient VOC removal with rapid kinetics. With their unique electronic and structural properties, graphitic carbon nitrides offer opportunities for photocatalytic degradation of VOCs under visible light. Catalysts integrated with MXene, a two-dimensional nanomaterial, exhibit enhanced catalytic activity for VOC oxidation reactions. Using various carbon-based materials in VOC removal showcases the versatility and effectiveness of carbon-based approaches in addressing environmental challenges associated with indoor air pollution. Metal-organic-framework materials are carbon-based compounds. It examines the correlation between VOC mineralization and specific characteristics of carbon materials, including surface area, adsorption capability, surface functional groups, and optoelectronic properties. Discussions include the basics of PCO, variables influencing how well catalysts degrade, and degradation mechanisms. It explores how technology will improve in the future to advance studies on healthy and sustainable indoor air quality.

Evolution of myoglobin diffusion mechanisms: exploring pore and surface diffusion in a single silica particle

This study elucidates the mass transfer mechanism of myoglobin (Mb) within a single silica particle with a 50 nm pore size at various pH levels (6.0, 6.5, 6.8, and 7.0). Investigation of Mb distribution ratio (R) and distribution kinetics was conducted using absorption microspectroscopy. The highest R was observed at pH 6.8, near the isoelectric point of Mb, as the electrostatic repulsion between Mb molecules on the silica surface decreased. The time-course absorbance of Mb in the silica particle was rigorously analyzed based on a first-order reaction, yielding the intraparticle diffusion coefficient of Mb (Dp). Dp-(1 + R)-1 plots at different pH values were evaluated using the pore and surface diffusion model. Consequently, we found that at pH 6.0, Mb diffused in the silica particle exclusively through surface diffusion, whereas pore diffusion made a more substantial contribution at higher pH. Furthermore, we demonstrated that Mb diffusion was hindered by slow desorption, associated with the electrostatic charge of Mb. This comprehensive analysis provides insights into the diffusion mechanisms of Mb at acidic, neutral, and basic pH conditions.

Mitigation of ammonia and hydrogen sulfide emissions during aerobic composting of laying hen waste through NaOH-modified biochar

The impact of NaOH-modified biochar on the release of NH3 and H2S from laying hens' manure was examined for 44 days, using a small-scale simulated aerobic composting system. The findings revealed that the NaOH-modified biochar reduced NH3 and H2S emissions by 40.63% and 77.78%, respectively, compared to the control group. Moreover, the emissions of H2S were significantly lower than those of the unmodified biochar group (p < 0.05). The increased specific surface area and microporous structure of the biochar, as well as the higher content of alkaline and oxygenated functional groups, were found to facilitate the adsorption of NH3 and H2S. This enhanced adsorption capability was the primary reason for the significant reduction in NH3 emissions. Furthermore, during the high-temperature phase of composting, there was a notable alteration in the microbial community. The abundance of Limnochordaceae, Savagea, and IMCC26207 increased significantly which aided in the conversion of H2S to stable sulfate. These microorganisms also influenced the abundance of functional genes involved in sulfur metabolism, thereby inhibiting cysteine synthesis, along with the decomposition and conversion of sulfate to sulfite. This led to a significant decrease in H2S emissions. This study provides valuable data for the selection of deodorizers in the composting process of egg-laying hens. The results have significant implications for the application of NaOH-modified biochar for odor reduction in aerobic composting processes.

Co-regulating the pore structure and surface chemistry of sludge-based biochar for high-performance deodorization of gaseous dimethyl disulfide

A straightforward and eco-friendly preparation method for porous sludge biochar (SBA-3) was developed to deodorize gaseous dimethyl disulfide (DMDS) using ion exchange to adjust micropore structures coupled with carboxyl functionalization. Compared with the unmodified sludge biochar SBA-1 and SBA-2 treated with ion exchange, the pore size of SBA-3 decreased accompanied with increasing specific surface area and micropore volume. The Brunauer-Emmett-Teller (BET) specific surface area and micropore volume were 176.35 and 0.0314 cm³ g-1, which were 2.02 and 1.71-fold larger than those of SBA-2, as well as 20.60 and 78.5-fold larger than those of SBA-1, respectively. Meanwhile, the amount of -COOH on the surface of SBA-3 increased from 0.425 to 1.123 mmol g-1, which was 2.64-fold larger than that of SBA-1. The adsorption behavior between DMDS and SBA-3 could be well described by the quasi-second-order kinetic model and Langmuir isotherm model. The maximum monolayer adsorption capacity was 35.12 mg g-1 at 303 K. Thermodynamic and DFT calculations indicated that the adsorption of DMDS on SBA-3 was exothermic with the deodorization mechanisms involving pore filling and chemisorption.

Enhanced Adsorption of Gaseous Naphthalene by Activated Carbon Fibers at Elevated Temperatures

This study utilized activated carbon fibers (ACFs) as adsorbents to investigate the removal efficiency of naphthalene and toluene at elevated temperatures and their competitive adsorption behavior. Three types of ACFs, inlet concentrations of naphthalene (343, 457, and 572 mg·Nm-3), and toluene (2055, 2877, and 4110 mg·Nm-3) were investigated to determine the adsorption capacities of naphthalene and toluene. To study the reaction mechanisms of naphthalene and toluene on the ACFs, the BET, SEM, FTIR, and TGA methods were used to examine the physical and chemical characteristics of ACFs. Results showed ACF-A's superior adsorption capacity for naphthalene that was attributed to its mesoporous structure and hydrophobicity. Adsorption equilibrium studies indicated multilayer adsorption behavior. Competitive adsorption experiments demonstrated the displacement of toluene by naphthalene on ACF-A, highlighting its higher selectivity for naphthalene. Functional group analysis revealed changes in ACF surfaces after naphthalene adsorption, suggesting π-π dispersion and electron donor-acceptor interactions. Overall, this study underscores the importance of pore structure and surface properties in designing ACFs for the efficient adsorption of high-boiling-point organic pollutants.

Treatment and Resource Utilization of Gaseous Pollutants in Functionalized Ionic Liquids

With the rapid development of science, technology, and the economy of human society, the emission problem of gas pollutants is becoming more and more serious, which brings great pressure to the global ecological environment. At the same time, the natural resources that can be exploited and utilized on Earth are also showing a trend of exhaustion. As an innovative and environmentally friendly material, functionalized ionic liquids (FILs) have shown great application potential in the capture, separation, and resource utilization of gaseous pollutants. In this paper, the synthesis and characterization methods of FILs are introduced, and the application of FILs in the treatment and recycling of gaseous pollutants is discussed. The future development of FILs in this field is also anticipated, which will provide new ideas and methods for the treatment and recycling of gaseous pollutants and promote the process of environmental protection and sustainable development.

Electrospinning and Partial Etching Behaviors of Core-Shell Nanofibers Directly Electrospun on Mesh Substrates for Application in a Cover-Free Compact Air Filter

The exposure of workers to propylene glycol monomethyl ether acetate (PGMEA) in manufacturing environments can result in potential health risks. Therefore, systems for PGMEA removal are required for indoor air quality control. In this study, core-shell zeolite socony mobil-5 (ZSM-5)/polyvinylpyrrolidone-polyvinylidene fluoride nanofibers were directly electrospun and partially wet-etched on a mesh substrate to develop a cover-free compact PGMEA air filter. The electrospinning behaviors of the core-shell nanofibers were investigated to optimize the electrospinning time and humidity and to enable the manufacture of thin and light air-filter layers. The partial wet etching of the nanofibers was undertaken using different etching solvents and times to ensure the exposure of the active sites of ZSM-5. The performances of the ZSM-5/PVDF nanofiber air filters were assessed by measuring five consecutive PGMEA adsorption-desorption cycles at different desorption temperatures. The synthesized material remained stable upon repeated adsorption-desorption cycles and could be regenerated at a low desorption temperature (80 °C), demonstrating a consistent adsorption performance upon prolonged adsorption-desorption cycling and low energy consumption during regeneration. The results of this study provide new insights into the design of industrial air filters using functional ceramic/polymer nanofibers and the application of these filters.

Silica-supported ionic liquid for efficient gaseous arsenic oxide removal through hydrogen bonding

The emission of highly-toxic gaseous As2O3 (As2O3 (g)) from nonferrous metal smelting poses environmental concerns. In this study, we prepared an adsorbent (SMIL-X) by loading an ionic liquid (IL) ([HOEtMI]NTf2) into MCM-41 through an impregnation-evaporation process and then applied it to adsorb As2O3 (g). SMIL-20% exhibited an As2O3 (g) adsorption capacity of 35.48 mg/g at 400 °C, which was 490% times higher than that of neat MCM-41. Characterization of SMIL-X indicated that the IL was mainly supported on MCM-41 through O-H…O bonds formed between the hydroxyl groups (-OH) and the silanol groups (Si-OH) and the O-H…F bonds formed between the C-F groups and the Si-OH groups. The hydrogen bonds significantly contributed to the adsorption of As2O3 (g), with -NH and -OH groups forming hydrogen bonds with As-O species (i.e., N-H…O and O-H…O). This showed superior performance to traditional adsorbents that rely on van der Waals forces and chemisorption. Moreover, after exposure to high concentrations of SO2, the adsorption capacities remained at 76% of their initial values, demonstrating some sulfur resistance. This study presents an excellent adsorbent for the purification of As2O3 (g) and shows promising application potential for treating flue gas emitted by nonferrous metal smelting processes.

Fluorination modification enhanced the water resistance of Universitetet i Oslo-67 for multiple volatile organic compounds adsorption under high humidity conditions: Mechanism study

The construction of metal-organic frameworks (MOFs) with highly efficient capture for volatile organic compounds (VOCs) adsorption under humid conditions is a significant yet formidable task. Herein, series of fluorinated UiO-67 modified with trifluoroacetic acid (TFA) and 4-fluorobenzoic acid were successfully synthesized for VOCs adsorption under high humidity conditions. Experiments results showed that UiO-67 modified with 4-fluorobenzoic acid (67-F) presented excellent adsorption capacity of 345 mg/g for toluene adsorption and exhibited great water resistance (10.0 vol% H2O, 374 mg/g toluene adsorption capacity). Characterization results indicated that the introduction of 4-fluorobenzoic acid induced the competitive coordination between 4-fluorobenzoic acid and 4,4-biphenyl dicarboxylic acid (BPDC) with Zr4+, causing the formation of abundant defects to provide extra adsorption sites. Meanwhile, the benzene ring in 4-fluorobenzoic acid enhanced the π-π conjugation, causing the further promotion of VOCs adsorption capacity. More importantly, the water resistance mechanism was investigated and elucidated that the introduction of F decreased the surface energy of 67-F and its affinity with water. Meanwhile, the metal complex induced by the fluorinated modification produced an electron-dense pore environment, which greatly improved its chemical and water stability. This work provided a strategy for preparing an adsorbent with high water resistance for real-world VOCs adsorption at high humidity conditions.

Data-driven, explainable machine learning model for predicting volatile organic compounds' standard vaporization enthalpy

The accurate prediction of standard vaporization enthalpy (ΔvapHm°) for volatile organic compounds (VOCs) is of paramount importance in environmental chemistry, industrial applications and regulatory compliance. To overcome traditional experimental methods for predicting ΔvapHm° of VOCs, machine learning (ML) models enable a high-throughput, cost-effective property estimation. But despite a rising momentum, existing ML algorithms still present limitations in prediction accuracy and broad chemical applications. In this work, we present a data driven, explainable supervised ML model to predict ΔvapHm° of VOCs. The model was built on an established experimental database of 2410 unique molecules and 223 VOCs categorized by chemical groups. Using supervised ML regression algorithms, the Random Forest successfully predicted VOCs' ΔvapHm° with a mean absolute error of 3.02 kJ mol-1 and a 95% test score. The model was successfully validated through the prediction of ΔvapHm° for a known database of VOCs and through molecular group hold-out tests. Through chemical feature importance analysis, this explainable model revealed that VOC polarizability, connectivity indexes and electrotopological state are key for the model's prediction accuracy. We thus present a replicable and explainable model, which can be further expanded towards the prediction of other thermodynamic properties of VOCs.

A comprehensive review and perspective research in technology integration for the treatment of gaseous volatile organic compounds

Volatile organic compounds (VOCs) are harmful pollutants emitted from industrial processes. They pose a risk to human health and ecosystems, even at low concentrations. Controlling VOCs is crucial for good air quality. This review aims to provide a comprehensive understanding of the various methods used for controlling VOC abatement. The advancement of mono-functional treatment techniques, including recovery such as absorption, adsorption, condensation, and membrane separation, and destruction-based methods such as natural degradation methods, advanced oxidation processes, and reduction methods were discussed. Among these methods, advanced oxidation processes are considered the most effective for removing toxic VOCs, despite some drawbacks such as costly chemicals, rigorous reaction conditions, and the formation of secondary chemicals. Standalone technologies are generally not sufficient and do not perform satisfactorily for the removal of hazardous air pollutants due to the generation of innocuous end products. However, every integration technique complements superiority and overcomes the challenges of standalone technologies. For instance, by using catalytic oxidation, catalytic ozonation, non-thermal plasma, and photocatalysis pretreatments, the amount of bioaerosols released from the bioreactor can be significantly reduced, leading to effective conversion rates for non-polar compounds, and opening new perspectives towards promising techniques with countless benefits. Interestingly, the three-stage processes have shown efficient decomposition performance for polar VOCs, excellent recoverability for nonpolar VOCs, and promising potential applications in atmospheric purification. Furthermore, the review also reports on the evolution of mathematical and artificial neural network modeling for VOC removal performance. The article critically analyzes the synergistic effects and advantages of integration. The authors hope that this article will be helpful in deciding on the appropriate strategy for controlling interested VOCs.

Ethylene Elimination Using Activated Carbons Obtained from Baru (Dipteryx alata vog.) Waste and Impregnated with Copper Oxide

Ethylene is a plant hormone regulator that stimulates chlorophyll loss and promotes softening and aging, resulting in a deterioration and reduction in the post-harvest life of fruit. Commercial activated carbons have been used as ethylene scavengers during the storage and transportation of a great variety of agricultural commodities. In this work, the effect of the incorporation of copper oxide over activated carbons obtained from baru waste was assessed. Samples were characterized by X-ray diffraction (XRD), N2 adsorption-desorption at -196 °C, field-emission scanning electron microscopy (FESEM) coupled with energy-dispersive X-ray spectroscopy (EDS), and infrared (IR) spectroscopy. The results showed that the amount of ethylene removed using activated carbon obtained from baru waste and impregnated with copper oxide (1667 μg g-1) was significantly increased in comparison to the raw activated carbon (1111 μg g-1). In addition, carbon impregnated with copper oxide exhibited better adsorption performance at a low ethylene concentration. Activated carbons produced from baru waste are promising candidates to be used as adsorbents in the elimination of ethylene during the storage and transportation of agricultural commodities at a lower cost.

Supported nano-sized precious metal catalysts for oxidation of catalytic volatile organic compounds

Volatile organic compounds (VOCs) are common contaminants found as indoor as well as outdoor pollutants, which can induce acute or chronic health hazards to the human physiological system. The catalytic oxidation method is widely considered as one of the effective methods for removing VOCs, and the development of highly effective catalysts is highly urgent for booming this interesting field. This review focuses on the recent progress of VOC oxidation catalyzed by supported nano-sized precious metal catalysts, and discusses the effects of metal composition, supports, size, and morphology on the catalytic activity. In addition, the roles played by both nano-sized precious metals and supports in enhancing the performance of catalytic VOCs are also systematically discussed, which will guide the further development of more advanced VOC catalysts.

Kinetic detection of hydrogen peroxide in single horseradish peroxidase-concentrated silica particle using confocal fluorescence microspectroscopic measurement

In the present study, we propose a scheme for detecting H2O2 by using horseradish peroxidase (HRP) adsorbed onto single silica particles and fluorescence microspectroscopy. When the silica particles were immersed in an HRP solution, the HRP concentration in the silica particles increased by a factor of 690 compared to that in the bulk aqueous solution because HRP was adsorbed on the silica surface. When a single particle containing HRP was added to a mixed solution of H2O2 and Amplex Red, fluorescence from resorufin, which was produced by the reaction of HRP, H2O2, and Amplex Red, was observed. The fluorescence from the resorufin in the particles increased after a single particle was added to the solution, and the release of resorufin was observed. As the concentration of H2O2 (CH2O2) decreased, the time it takes for fluorescence intensity to reach its maximum was shorter. The detection limit for H2O2 in the present system was 980 nM. The reaction behavior of a single silica particle was evaluated using a spherical diffusion model, which explains the approximate concentration change of resorufin in the silica particle. The proposed method has the advantages of simple sample preparation and detection, low sample consumption, and a short detection time.

One-step fabrication of millimeter-scale hollow vesicles with chitosan /DADMAC/ sodium alginate graft copolymer for enhanced anionic dye adsorption

Hollow vesicles are promising in water treatment due to their unique structure of the membrane and inner cavity. However, the adsorption capacity needs to be improved for targeted pollutants. Herein, millimeter-scale hollow vesicles were prepared with a one-step process of sequential stirring and grafting using chitosan, diallyldimethylammonium chloride, and sodium alginate as raw materials with the purpose of efficient removal of anionic dyes from wastewater. The composite vesicles were characterized using scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction. The hollow vesicles showed the structure of the cationic membrane and the inner cavity, facilitating the dye adsorption. The adsorption capacity for the anionic dye Reactive Black 5 reached 698.1 mg/g, more than twice that of the binary composite vesicles without graft. The adsorption kinetics and isotherm data coincided with the pseudo-second-order and Langmuir models, respectively, and the adsorption mechanism was monolayer chemisorption. Moreover, the vesicles worked well in wide ranges of environment pH, temperature, and co-existing pollutants. They also possessed excellent cyclic regeneration performance, in which 93 % of the initial adsorption capacity was maintained after four cycles. These results indicate that the millimeter-scale hollow vesicles exhibit broad application prospects for wastewater purification.

A photo-active hollow covalent organic frameworks microcapsule imparts highly efficient photoredox catalysis of gaseous volatile organic compounds

Covalent organic frameworks (COFs) with controlled porosity, high crystallinity, diverse designability and excellent stability are very attractive in metal-free heterogeneous photocatalysis of volatile organic compounds (VOCs) degradation. In order to construct the high optimal performance COFs under feasible and universal conditions, herein, the visible light-driven hollow COFTAPB-PDA (H-COFTAPB-PDA) microcapsule was designed by a facile dual-ligand regulated sacrificial template method. The H-COFTAPB-PDA microcapsule possesses improved surface area, high crystallinity, broad absorption range and high stability, which enables enhanced substrates and visible light adsorption, photogenerated electrons-holes separation and transfer, and facilitate the generation of reactive radicals. Importantly, it was found to be a highly efficient photocatalyst for toluene degradation under visible-light irradiation compared with the solid COFTAPB-PDA, and the degradation efficiency of toluene reached 91.8 % within 180 min with the conversion rate of CO2 was 68.9 %. Additionally, the H-COFTAPB-PDA presented good recyclability and long-term stability after multiple photocatalytic reuses. Furthermore, the active sites of H-COFTAPB-PDA in photocatalytic degradation of toluene was proposed by XPS and DFT calculations, and the degradation pathway and mechanism was proposed and analyzed. The result presented great prospect of morphologic design of hollow COFs in metal-free heterogeneous photocatalysis for VOCs degradation.

A facile method for preparing the CeMnO3 catalyst with high activity and stability of toluene oxidation: The critical role of small crystal size and Mn3+-Ov-Ce4+ sites

Volatile organic compounds (VOCs) cause severe environmental pollution and are potentially toxic to humans who have no defense against exposure. Catalytic oxidation of these compounds has thus become an interesting research topic. In this study, microcrystalline CeMnO3 catalysts were prepared by a precipitant-concentration-induced strategy and evaluated for the catalytic oxidation of toluene/benzene. The effect of crystal size on catalytic performance was confirmed by XRD, TEM, N2 adsorption-desorption, XPS, Raman, H2-TPR, and TPSR. The CeMnO3 catalyst with more Mn3+-Ov-Ce4+ active sites exhibited enhanced VOCs catalytic oxidation performance, lowest active energy, and highest turnover frequency, which was attributed to its larger surface area, lower crystal size, higher low-temperature reducibility, and presence of more oxygen defects. In-situ FTIR results suggested more oxygen vacancies can profoundly promote the conversion of benzoate to maleate species, the rate-determining step of toluene oxidation. The work provides a convenient and efficient strategy to prepare single-metal or multi-metal oxide catalysts with smaller crystal sizes for VOC oxidation or other oxidation reactions.

Enhanced adsorption of toluene on thermally activated ZIF-67: Characterization, performance, and modeling insights

The zeolitic imidazolate framework-67 (ZIF-67) has been explored for the dynamic adsorption of toluene vapor. We synthesized ZIF-67 through a straightforward room-temperature process and characterized it using XRD, FT-IR, DLS, and SEM techniques. The synthesized ZIF-67 possessed a Brunauer-Emmett-Teller (BET) surface area of 1578.7 m2/g and 0.76 μm particle size. Thermal activation under various conditions revealed that ZIF-67, activated in dry air at 250 °C, demonstrated optimal adsorption efficacy. Its adsorption capacity, time of breakthrough, and time of equilibration were 414.5 mg/g, 420 min, and 795 min, respectively. We investigated the impact of diverse operational parameters on adsorption through breakthrough curve analysis. An increase in the toluene concentration from 100 to 1000 ppm enhanced the adsorption capacity from 171 to 414 mg/g, while breakthrough time decreased from 1260 min to 462 min, respectively. Our findings show that increasing relative humidity from 0 to 70 % reduced 53.7 % in adsorption capacity and 46.3 % in breakthrough time. The competitive adsorption of toluene and ethylbenzene revealed that ZIF-67 had a higher selectivity for toluene adsorption. A 98 % adsorbent's regeneration efficiency at the first cycle reveals its reusability. The experimental data were successfully fitted to the Yan, Thomas, and Yoon-Nelson models to describe the adsorption process. The statistical validation of the model parameters confirms their reliability for estimating adsorption parameters, thus facilitating the design of fixed-bed adsorption columns for practical applications.

Micro- and Mesoporous Structural Effects of Beta Zeolites for Volatile Organic Compound Sorption

To fully exploit pore engineering in the design of more efficient zeolite adsorbents for volatile organic compound (VOC) treatment, the roles of meso- and micropores need to be clarified to provide the theoretical basis and feasible measures. In this work, the three VOC sorption properties of conventional and hierarchical porous beta zeolites were comparatively investigated to study the roles of meso- and micropores. There is a division of functions between micro- and mesopores, with micropores being the main VOC adsorption sites and mesopores greatly enhancing VOC diffusion and adsorbent reusability. On the one hand, micropores should be preserved as much as possible because obtaining mesopores by sacrificing micropores (i.e., alkali treatment) results in 28-60% decreases in adsorption capacities. On the other hand, mesopore introduction is highly desirable, which results in an enhancement of VOC intraparticle diffusion rates by 1.3-2.3 times (at the VOC concentration of 600 ppm) and chlorobenzene adsorption capacity on the 20th cycle increasing from 78% of the initial value to 89 and 93%. The findings may provide valuable information about zeolite-based adsorbents for adsorption removal or recovery of VOCs.

Insights into the role of VOCs properties on thermal desorption behaviors of two porous polymeric resins

Desorption is a critical process in the recovery or post-treatment of adsorbents saturated with volatile organic compounds (VOCs). In this study, the thermal desorption behaviors for eight VOCs on hypercrosslinked polymeric resin (HPR) and macroporous polymeric resin (MPR) were investigated through isothermal desorption and temperature programmed desorption (TPD). Compared with MPR, HPR with more micropores exhibited a lower desorption rate constant, lower desorption efficiency and higher desorption activation energy due to the strong binding energy generated between VOCs molecules and narrow micropores. As the polarizability of VOCs increased, the desorption rate constants on two porous polymeric resins decreased, while the desorption activation energy showed an incremental trend. Excellent linear correlations were observed between VOC polarizability and desorption rate constants (R2 = 0.957 for HPR and R2 = 0.940 for MPR) as well as between VOC polarizability and desorption activation energy (R2 = 0.981 for HPR and R2 = 0.969 for MPR). Furthermore, a polyparameter linear free energy relationship (PP-LFER) was developed to explore the influences of intermolecular interactions on desorption behaviors of VOCs on porous polymeric resins. The results indicated that the dispersive interaction, which is directly related to polarizability of VOCs, was the primary factor influencing the desorption activation energy of VOCs on porous polymeric resins. The find from this study helps evaluate fleetly and availably the desorption properties of VOCs based on their polarizability.

Cooperative and Bifunctional Adsorbent-Catalyst Materials for In-situ VOCs Capture-Conversion

Volatile organic compounds (VOCs) are gases that are emitted into the air from products or processes and are major components of air pollution that significantly deteriorate air quality and seriously affect human health. Different types of metals, metal oxides, mixed-metal oxides, polymers, activated carbons, zeolites, metal-organic frameworks (MOFs) and mixed-matrixed materials have been developed and used as adsorbent or catalyst for diversified VOCs detection, removal, and destruction. In this comprehensive review, we first discuss the general classification of VOCs removal materials and processes and outline the historical development of bifunctional and cooperative adsorbent-catalyst materials for the removal of VOCs from air. Subsequently, particular attention is devoted to design of strategies for cooperative adsorbent-catalyst materials, along with detailed discussions on the latest advances on these bifunctional materials, reaction mechanisms, long-term stability, and regeneration for VOCs removal processes. Finally, challenges and future opportunities for the environmental implementation of these bifunctional materials are identified and outlined with the intent of providing insightful guidance on the design and fabrication of more efficient materials and systems for VOCs removal in the future.

An effective strategy for biodegradation of high concentration phenol in soil via biochar-immobilized Rhodococcus pyridinivorans B403

High concentration of phenol residues in soil are harmful to human health and ecological safety. However, limited information is available on the in-situ bioremediation of phenol-contaminated soil using biochar as a carrier for bacteria. In this study, bamboo -derived biochar was screened as a carrier to assemble microorganism-immobilized composite with Rhodococcus pyridinivorans B403. Then, SEM used to observe the micromorphology of composite and its bioactivity was detected in solution and soil. Finally, we investigated the effects of free B403 and biochar-immobilized B403 (BCJ) on phenol biodegradation in two types of soils and different initial phenol concentrations. Findings showed that bacterial cells were intensively distributed in/onto the carriers, showing high survival. Immobilisation increased the phenol degradation rate of strain B403 by 1.45 times (37.7 mg/(L·h)). The phenol removed by BCJ in soil was 81% higher than free B403 on the first day. Moreover, the removal of BCJ remained above 51% even at phenol concentration of 1,500 mg/kg, while it was only 15% for free B403. Compared with the other treatment groups, BCJ showed the best phenol removal effect in both tested soils. Our results indicate that the biochar-B403 composite has great potential in the remediation of high phenol-contaminated soil.

Aluminium phosphide (Al12P12) nanocage as a potential sensor for volatile organic compounds: A DFT study

The efficacy of aluminium phosphide (Al12P12) nanocage toward sensing methanol (MeOH) and ethanol (EtOH) volatile organic compounds (VOCs) was herein thoroughly elucidated utilizing various density functional theory (DFT) computations. In this perspective, MeOH⋯ and EtOH⋯Al12P12 complexes were investigated within all plausible configurations. According to the energetic features, the EtOH⋯Al12P12 complexes exhibited larger negative values of adsorption and interaction energies with values up to -27.23 and -32.84 kcal mol-1, respectively, in comparison to the MeOH⋯Al12P12 complexes. Based on the symmetry-adapted perturbation theory (SAPT) results, the electrostatic forces were pinpointed as the predominant component beyond the adsorption process within the preferable MeOH⋯ and EtOH⋯Al12P12 complexes. The findings of the noncovalent interaction (NCI) index and quantum theory of atoms in molecules (QTAIM) outlined the closed-shell nature of the interactions within the studied complexes. Substantial variations were found in the molecular orbitals distribution patterns of MeOH/EtOH molecules and Al12P12 nanocage, outlining the occurrence of the adsorption process within the complexes under investigation. Thermodynamic parameters were denoted with negative values, demonstrating the spontaneous exothermic nature of the most favorable complexes. New energy states were observed within the extracted density of states plots, confirming the impact of adsorbing MeOH and EtOH molecules on the electronic properties of the Al12P12 nanocage. The appearance of additional peaks in Infrared Radiation (IR) and Raman spectra revealed the apparent effect of the adsorption process on the features of the utilized sensor. The emerging results declared the potential uses of Al12P12 nanocage as a promising candidate for sensing VOCs, particularly MeOH and EtOH.

A theoretical study on toluene oxidization by OH radical

Toluene, a prominent member of volatile organic compounds (VOCs), exerts a substantial adverse influence on both human life and the environment. In the context of advanced oxidation processes, the ·OH radical emerges as a highly efficient oxidant, pivotal in the elimination of VOCs. This study employs computational quantum chemistry methods (G4MP2//B3LYP/6-311++G(d,p)) to systematically investigate the degradation of toluene by ·OH radicals in an implicit solvent model, and validates the rationale of choosing a single-reference method using T1 diagnostics. Our results suggest three possible reaction mechanisms for the oxidation of toluene by ·OH: firstly, the phenyl ring undergoes a hydrogen abstraction reaction followed by direct combination with ·OH to form cresol; secondly, ·OH directly adds to the phenyl ring, leading to ring opening; thirdly, oxidation of sidechain to benzoic acid followed by further addition and ring opening. The last two oxidation pathways involve the ring opening of toluene via the addition of ·OH, significantly facilitating the process. Therefore, both pathways are considered feasible for the degradation of toluene. Subsequently, the UV-H2O2 system was designed to induce the formation of ·OH for toluene degradation and to identify the optimal reaction conditions. It was demonstrated that ·OH and 1O2 are the primary active species for degrading toluene, with their contribution ranking as ·OH > 1O2. The intermediates in the mixture solution after reactions were characterized using GC-MS, demonstrating the validity of theoretical predictions. A comparative study of the toluene consumption rate revealed an experimental comprehensive activation energy of 10.33 kJ/mol, which is consistent with the preliminary activation energies obtained via theoretical analysis of these three mechanisms (0.56 kJ/mol to 13.66 kJ/mol), indicating that this theoretical method can provide a theoretical basis for experimental studies on the oxidation of toluene by ·OH.

Enhanced benzene vapor adsorption through microwave-assisted fabrication of activated carbon from peanut shells using ZnCl2 as an activating agent

Herein, microwave-assisted activated carbon (MW-AC) was fabricated from peanut shells using a ZnCl2 activator and utilized for the first time to eliminate benzene vapor as a volatile organic compound (VOC). During the MW-AC production process, which involved two steps-microwave treatment and muffle furnace heating-we investigated the effects of various factors and achieved the highest iodine number of 1250 mg/g. This was achieved under optimal operating conditions, which included a 100% impregnation ratio, CO2 as the gas in the microwave environment, a microwave power set at 500 W, a microwave duration of 10 min, an activation temperature of 500 °C and an activation time of 45 min. The structural and morphological properties of the optimized MW-AC were assessed through SEM, FTIR, and BET analysis. The dynamic adsorption process of benzene on the optimized MW-AC adsorbent, which has a significant BET surface area of 1204.90 m2/g, was designed using the Box-Behnken approach within the response surface methodology. Under optimal experimental conditions, including a contact duration of 80 min, an inlet concentration of 18 ppm, and a temperature of 26 °C, the maximum adsorption capacity reached was 568.34 mg/g. The experimental data are better described by the pseudo-second-order kinetic model, while it is concluded that the equilibrium data are better described by the Langmuir isotherm model. MW-AC exhibited a reuse efficiency of 86.54% for benzene vapor after five consecutive recycling processes. The motivation of the study highlights the high adsorption capacity and superior reuse efficiency of MW-AC adsorbent with high BET surface area against benzene pollutant. According to our results, the developed MW-AC presents itself as a promising adsorbent candidate for the treatment of VOCs in various industrial applications.

Enhanced ability of toluene oxidation by controlling inversion degree of spinel composed of only Co, Mn

Exploring the single relationship between the inversion degree of spinel and its catalytic performance is a great challenge, but has important significance for further structural design and application. A series of CoMn inverse spinels were prepared and the general formula [Formula: see text] was deduced through X-ray diffraction refinement to find a decreased inversion degree x as calcination temperature rose. Catalytic oxidation of toluene showed that higher inversion degree (S-300 with x ≈ 0.95) can reach larger conversion rate (90 % at about 250 °C for 400 ppm toluene) with greater reaction stability (140 h). Density Functional Theory (DFT) calculations on density of states indicated its metallic nature, and found that the strength of O-p and Transition metal-d orbitals at Fermi energy is positively correlated to the inversion degree, meaning stronger electron migration ability. Along with the adsorption calculation analysis that lattice oxygen species are proved to work dominantly (S-300 with lowest adsorption energy but highest performance), this work uncovered a theoretical insight into inverse spinel oxide, to provide the possibility of elevated oxidation ability through structural control.

Enhancement of Pb(ii) adsorptive removal by incorporation of UiO-66-COOH into the magnetic graphitic carbon nitride nanosheets

Efficient elimination of Lead (Pb(ii)) from aqueous solutions has become a crucial area of focus in the wastewater treatment industry. In this study, novel mesoporous magnetic g-C3N4/Fe3O4/UiO-66-COOH was synthesized by combining the acid-functionalized metal-organic framework (MOF) of UiO-66-COOH via a facile novel solvothermal method with magnetic graphitic carbon nitride (g-C3N4/Fe3O4) sheets to enhance Pb(ii) adsorption in water. The study investigated various influential adsorption parameters, including pH, dosage, contact time, ion concentration, and temperature. The Langmuir model, which depicts monolayer adsorption on a uniform surface, was a more suitable fit for the adsorption isotherms. The kinetics conformed to the pseudo-second-order model, indicating a chemical adsorption mechanism. According to the Langmuir model, the adsorption capacity of g-C3N4/Fe3O4/UiO-66-COOH is expected to reach a maximum of 285.8 mg L-1. This value is 2.6 times higher than g-C3N4/Fe3O4 and 1.6 times higher than UiO-66-COOH. The enhanced adsorption capacity of g-C3N4/Fe3O4/UiO-66-COOH is attributed to its superior characteristics, such as abundant functional groups and high surface area which is 2.16 times higher than g-C3N4/Fe3O4. The adsorption thermodynamics indicated that the adsorption occurred spontaneously and was characterized as exothermic. g-C3N4/Fe3O4/UiO-66-COOH material exhibited good recyclability for up to five runs.

Data-driven autonomous operation of VOCs removal system

Removal of volatile organic compounds (VOCs) from the air has been an important issue in many industrial fields. Traditionally, the operation of VOCs removal systems has relied on fixed operating conditions determined by domain experts based on their expertise and intuition. In practice, this manual operation cannot respond immediately to changes in the system environment. To facilitate the autonomous operation of the system, the operating conditions should be optimized properly in real time to adapt to the changes in the system environment. Recently, optimization frameworks have been widely applied to real-world industrial systems across various domains using different approaches. The primary motivation for this study is the effective implementation of an optimization framework targeting a VOCs removal system. In this paper, we present a data-driven autonomous operation method for optimizing the operating conditions of a VOCs removal system to enhance the overall performance. An optimization problem is formulated with the decision variables denoting the parameters associated with the operating condition, the environmental variables representing the measurements for the system environment, the constraints specifying the control ranges of the parameters, and the objective function representing the system performance as determined by the operating conditions and environment. Using the previous operation data from the system, a neural network is trained to model the system performance as a function of the decision and environmental variables to approximate the objective function. For the current state of the system environment, the optimal operating condition is derived by solving the optimization problem. A case study of a targeted VOCs removal system demonstrates that the proposed method effectively optimizes the operating conditions for improved system performance without intervention from domain experts.

Effect of Adding Bentonite to Porous Silica via the Sol-Gel Method

The control of specific surface area and pore size of porous materials is essential for applications such as optics, medicine, and food technology. Here, the interspace between nanomaterials such as nanoparticles and nanosheets was studied. Nanoparticle-nanosheet interspaces were formed by incorporating bentonite nanosheets to the preparation of porous silica by the sol-gel method. The product had micropore and mesopores, which originated from internanoparticle space and nanoparticle-nanosheet spaces, respectively. These two types of pores had not only different sizes but also different aspect ratios. Time-domain nuclear magnetic resonance evaluation of the bentonite dispersion revealed that the dispersion state of bentonite in water prior to composite fabrication affected the formation of the pore structure. The pore size distribution could be easily changed by adding two-dimensional and flexible nanosheets owing to the change in the physical properties of the product. The silica-bentonite composite had a significantly larger specific surface area and pore volume than porous silica without bentonite. Water vapor adsorption measurements showed that the composite exhibited a larger maximum adsorption in comparison to porous silica. Therefore, a large improvement in the physical properties can be achieved by combining nanomaterials with different geometries.

Association of volatile organic compound exposure with metabolic syndrome and its components: a nationwide cross-sectional study

BACKGROUND

Metabolic syndrome (MetS) is a health issue consisting of multiple metabolic abnormalities. The impact of exposure to volatile organic compounds (VOCs) on MetS and its components remains uncertain. This study aimed to assess the associations of individual urinary metabolites of VOC (mVOCs) and mVOC mixtures with MetS and its components among the general adult population in the United States.

METHODS

A total of 5345 participants with eligible data were filtered from the 2011-2020 cycles of the National Health and Nutrition Examination Survey. Multivariate logistic regression models were applied to assess the associations of individual mVOCs with MetS and its components. The least absolute shrinkage and selection operator (LASSO) regression models were constructed to identify more relevant mVOCs. The weight quantile sum regression model was applied to further explore the links between mVOC co-exposure and MetS and its components.

RESULTS

The results indicated positive associations between multiple mVOCs and MetS, including CEMA, DHBMA, and HMPMA. CEMA was found to be positively correlated with all components of MetS. HMPMA was associated with elevated triglyceride (TG), reduced high-density lipoprotein, and fasting blood glucose (FBG) impairment; 3HPMA was associated with an elevated risk of high TG and FBG impairment; and DHBMA had positive associations with elevated TG and high blood pressure. The co-exposure of LASSO-selected mVOCs was associated with an increased risk of elevated TG, high blood pressure, and FBG impairment.

CONCLUSION

Positive associations of certain individual urinary mVOCs and mVOC mixtures with MetS and its components were observed by utilizing multiple statistical models and large-scale national data. These findings may serve as the theoretical basis for future experimental and mechanistic studies and have important implications for public health.

Development of activated carbons derived from wastes: coffee grounds and olive stones as potential porous materials for air depollution

Agro-industrial byproducts and food waste necessitate an environmentally friendly way of reducing issues related to their disposal; it is also necessary to recover as much new raw material from these resources as possible, especially when we consider their potential usage as a precursor for preparing depolluting materials, such as activated carbon. In this work, coffee grounds and olive stones were chosen as precursors and the adsorption capacity of the obtained porous carbons for volatile organic compounds (VOCs) was studied. Microporous activated carbons (ACs) were prepared using chemical (K2CO3) and physical (CO2) activation. The influence of the activation process, type, and time of activation was also investigated. Measurements of VOCs adsorption were performed, and methyl-ethyl-ketone (MEK) and toluene were chosen as the model pollutants. The surface areas and total pore volumes of 1487 m2/g and 0.53 cm3/g and 870 m2/g and 0.22 cm3/g for coffee ground carbons and olive stone carbons, respectively, were obtained via chemical activation, whereas physical activation yielded values of 716 m2/g and 0.184 cm3/g and 778 cm2 g-1 and 0.205 cm3/g, respectively. As expected, carbons without activation (biochars) showed the smallest surface area, equal to 331 m2/g and 251 m2/g, and, hence, the lowest adsorption capacity. The highest adsorption capacity of MEK (3210 mg/g) and toluene (2618 mg/g) was recorded for chemically activated coffee grounds. Additionally, from the CO2 isotherms recorded at a low pressure (0.03 bar) and 0 °C, the maximum CO2 adsorption capacity was equal to 253 mg/g.

Defective UiO-66 metal-organic gels for optimizing gaseous toluene capture

Developing high-performance sorbents for volatile organic compounds (VOCs) is urgently required for environmental cleaning and personnel protection. Zirconium-based metal-organic frameworks (Zr-MOFs) have been deemed attractive candidates for gaseous toluene capture due to their superior stability and high adsorption capacity. However, the practical application of powdered Zr-MOFs is hindered by inherent limitations. Here, we report a series of defective UiO-66 metal-organic gels (G66-X) with variable missing linker deficiency by altering the modulator concentration. The defect concentration of the adsorbents has a significant impact on the porosity and gaseous toluene adsorption capacity. Dynamic breakthrough results reveal that G66-9 demonstrates optimal breakthrough time of 336 min/g and uptake amount of 334 mg/g, outperforming those of many other typical toluene adsorbents. The breakthrough times and the uptake capacities dramatically decrease with the increase of adsorption temperature. An outstanding regeneration performance of adsorbents can almost maintain even after five adsorption-desorption cycles.

Performance and mechanism of benzene adsorption on ZnCl2 one-step modified corn cob biochar

Utilizing cost-effective corn cob, zinc chloride-modified biochar was synthesized through one-step method for benzene adsorption from air. Study on impregnation ratio impact showed optimal benzene adsorption at ZnCl2:CC ratio of 1.5:1, with capacity reaching 170.53 mg g-1. Characterization using BET, SEM, FTIR, and XPS was conducted. BET results indicated specific surface area of Zn1.5BC at 1260.63 m2 g-1 and maximum pore volume of 0.546 m3 g-1. SEM analysis revealed microporous-mesoporous structure in Zn1.5BC, marking significant improvement over original biomass. DFT pore size distribution and FTIR analysis suggested post-modification dehydration and elimination reactions, leading to volatile compound release, functional group reduction, and pore widening. XPS analysis showed decrease in O = C-OH content with increased impregnation ratio, enhancing biochar's π-π electron diffusion for benzene. Langmuir isotherm and pseudo-second-order kinetic models effectively described experimental data, indicating multilayer benzene adsorption on biochar controlled by complex physicochemical adsorption and pore diffusion. Adsorption condition assessment, including adsorption temperature (20-120 ℃) and benzene concentration in inlet phase (159.73-383.36 mg L-1), was performed. Yoon-Nelson model fitting indicated adsorption site loss at higher temperatures and reduced capture ability due to increased adsorbate molecule kinetic energy. Higher adsorbate concentrations aided adsorption molecule diffusion to biochar surface and internal pores, increasing adsorption rate and shortening equilibrium time. Overall, zinc chloride-modified biochar facilitates benzene adsorption through pore filling and π-π interactions, with pore filling as primary mechanism. Produced biochar shows excellent regeneration properties and reusability.

Enhanced adsorption of aromatic VOCs on hydrophobic porous biochar produced via microwave rapid pyrolysis

To customize biochar suitable for efficient adsorption of benzene derivatives, this study presents programmed microwave pyrolysis to produce hydrophobic porous biochar with low-dose ferric chloride. Designated control of the ramping rates in the carbonization stage and the temperatures in the activation stage were conducive to enlarging the specific surface area. Iron species, including amorphous iron minerals, could create small-scale hotspots during microwave pyrolysis to promote microporous structure development. Compared with conventional pyrolysis, programmed microwave pyrolysis could increase the specific surface area from 288.6 m2 g-1 to 455.9 m2 g-1 with a short heating time (15 min vs. 2 h) under 650 °C. Engineered biochar exhibited higher adsorption capacity for benzene and toluene (136.6 and 94.6 mg g-1), and lower adsorption capacity for water vapour (6.2 mg g-1). These findings provide an innovative design of engineered biochar for the adsorption of volatile organic compounds in the environment.

Adsorptive interaction between typical VOCs and various topological zeolites: Mixture effect and mechanism

Adsorption is one of the most feasible and effective methods to alleviate the volatile organic compounds (VOCs) pollution. However, the mixture effect and mechanism for competitive adsorption of VOCs on zeolites are barely addressed. In this study, toluene, acetone, and ethyl acetate as prevalent VOCs species were removed by four potential zeolites (13X, USY, Beta, ZSM-5) in both single- and multi-component systems. The structure-property relationship between adsorbate-adsorbent pairs was revealed by X-ray diffraction, scanning electron microscopy, energy dispersive spectrometer, X-ray fluorescence, N2 adsorption and density function theory calculation. The molecular polarity and volatility of VOCs species played key roles in adsorption and the dynamic uptakes were generally listed as follows: ethyl acetate > toluene > acetone. As for the above VOCs mixtures, 13X zeolite selectively adsorbed oxygenated VOCs rather than toluene. In contrast, USY exhibited a preference to trap toluene. Ethyl acetate could be readily enriched by ZSM-5 and Beta selectively. The possible explanations and implications are discussed based on the subtle change in electron density. The results obtained are vital for understanding the mixture effect of VOCs adsorption and may guide the selection of proper adsorbent for real applications.

Bifunctional Cu-incorporated carbon nanospheres via in-situ complexation strategy as efficient toluene adsorbents and antibacterial agents

Carbon adsorbents have been widely used to remove indoor volatile organic compounds (VOCs), however, the proliferation of bacteria on the carbon adsorbents may deteriorate the indoor air quality and thus pose a serious threat to human health. Herein, we report the synthesis of antibacterial porous carbon spheres (carbonized aminophenol-formaldehyde resin, CAF) with well-dispersed Cu species via an in situ incorporation of Cu2+ during the polymerization of 3-aminophenol-formaldehyde resin followed by a thermal carbonization and reduction process. Compared with CAF, the Cu/CAF-x nanocomposites with Cu loading show a much higher specific surface area (>700 m2 g-1vs. 569 m2 g-1 for CAF). In addition, the pore size of Cu/CAF-x is ranging from 0.7 to 1.68 nm, which is exactly conducive to adsorb the toluene molecules. As a result, the toluene adsorption capacity is improved from 123.50 mg g-1 for CAF to >170 mg g-1 for Cu/CAF-x. More importantly, such adsorbents possess excellent antibacterial performance, the Cu/CAF-10 (10 wt% of Cu loading) with a concentration of 50 μg mL-1 can completely kill the E. coli within 30 min. Our work paves the way to the development of bifunctional adsorbents with both efficient VOCs adsorption and excellent antibacterial performance.

Ambient-mediated wetting on smooth surfaces

A consensus was built in the first half of the 20th century, which was further debated more than 3 decades ago, that the wettability and condensation mechanisms on smooth solid surfaces are modified by the adsorption of organic contaminants present in the environment. Recently, disagreement has formed about this topic once again, as many researchers have overlooked contamination due to its difficulty to eliminate. For example, the intrinsic wettability of rare earth oxides has been reported to be hydrophobic and non-wetting to water. These materials were subsequently shown to display dropwise condensation with steam. Nonetheless, follow on research has demonstrated that the intrinsic wettability of rare earth oxides is hydrophilic and wetting to water, and that a transition to hydrophobicity occurs in a matter of hours-to-days as a consequence of the adsorption of volatile organic compounds from the ambient environment. The adsorption mechanisms, kinetics, and selectivity, of these volatile organic compounds are empirically known to be functions of the substrate material and structure. However, these mechanisms, which govern the surface wettability, remain poorly understood. In this contribution, we introduce current research demonstrating the different intrinsic wettability of metals, rare earth oxides, and other smooth materials, showing that they are intrinsically hydrophilic. Then we provide details on research focusing on the transition from wetting (hydrophilicity) to non-wetting (hydrophobicity) on somooth surfaces due to adsorption of volatile organic compounds. A state-of-the-art figure of merit mapping the wettability of different smooth solid surfaces to ambient exposure as a function of the surface carbon content has also been developed. In addition, we analyse recent works that address these wetting transitions so to shed light on how such processes affect droplet pinning and lateral adhesion. We then conclude with objective perspectives about research on wetting to non-wetting transitions on smooth solid surfaces in an attempt to raise awareness regarding this surface contamination phenomenon within the engineering, interfacial science, and physical chemistry domains.

Comprehensive Qualitative and Quantitative Colorimetric Sensing of Volatile Organic Compounds Using Monolayered Metal-Organic Framework Films

Cross-responsive chemical sensors are in high demand owing to their ability to distinguish a broad range of analytes. In this study, a vapochromic sensor array based on metal-organic frameworks (MOFs), which exhibits distinct patterns when exposed to volatile organic compounds (VOCs) and humidity, is developed. Conventional sensor arrays consist of various receptors that produce different responses. The vapochromic MOF-based sensor comprises dicopper paddlewheel clusters and dimethylamine azobenzene as binary colorimetric sensing moieties. Upon exposure to VOCs, the constructed sensor encompasses a broad spectrum of colors, ranging from green to red. Furthermore, the color of the MOF is influenced by the solvent used during the pretreatment. Consequently, monolayered MOF thin films can be adapted to multicomponent array systems by immersing the MOF in different solvents. This system provides both qualitative and quantitative sensing, generating unique color patterns corresponding to specific VOC types. Notably, the sensor successfully discriminates each of 14 common VOCs and water and accurately categorizes unknown samples. Moreover, the system undergoes reversible color changes in response to humidity, obviating the need for high-temperature regeneration steps. This novel approach offers insights into the versatile applications of MOFs by creating a colorimetric sensor array capable of detecting various analytes.

Facile Preparation of Polyacrylonitrile-Based Activated Carbon Fiber Felts for Effective Adsorption of Dipropyl Sulfide

Activated carbon fibers (ACFs) derived from various polymeric fibers with the characteristics of a high specific surface area, developed pore structure, and good flexibility are promising for the new generation of chemical protection clothing. In this paper, a polyacrylonitrile-based ACF felt was prepared via the process of liquid phase pre-oxidation, along with a one-step carbonization and chemical activation method. The obtained ACF felt exhibited a large specific surface area of 2219.48 m2/g and pore volume of 1.168 cm3/g, as well as abundant polar groups on the surface. Owing to the developed pore structure and elaborated surface chemical property, the ACF felt possessed an intriguing adsorption performance for a chemical warfare agent simulant dipropyl sulfide (DPS), with the highest adsorption capacity being 202.38 mg/g. The effects of the initial concentration of DPS and temperature on the adsorption performance of ACF felt were investigated. Meanwhile, a plausible adsorption mechanism was proposed based on the kinetic analysis and fitting of different adsorption isotherm models. The results demonstrated that the adsorption process of DPS onto ACF felt could be well fitted with a pseudo-second-order equation, indicating a synergistic effect of chemical adsorption and physical adsorption. We anticipate that this work could be helpful to the design and development of advanced ACF felts for the application of breathable chemical protection clothing.

Efficient Adsorptive Removal of Methylene Blue Dye from Aqueous Solution Using Eragrostis Teff Biomass-Derived Nitrogen and Phosphorus-Codoped Carbon Quantum Dots

Carbon quantum dots have a great application potential in environmental protection via adsorption technology due to their large specific surface area and negative zeta potential. In this work, nitrogen and phosphorus-codoped carbon quantum dots (NP-CQDs) with a large specific surface area and negative zeta potential were successfully synthesized by a single-step hydrothermal synthesis. Batch adsorption studies were utilized to assess the adsorbent's capacity to remove common methylene blue (MB) dye contaminants from an aqueous solution. The experiment showed that MB dye could be removed in 30 min under optimum experimental conditions, with a removal efficiency of 93.73%. The adsorbent's large surface area of 526.063 m2/g and negative zeta potential of -12.3 mV contribute to the high removal efficiency. The Freundlich isotherm model fits the adsorption process well at 298 K, with R2 and n values of 0.99678 and 4.564, respectively, indicating its applicability. A kinetic study demonstrated that the pseudo-second-order model, rather than the pseudo-first-order model, is more suited to represent the process of MB dye adsorption onto NP-CQDs. This research established a simple and cost-effective method for developing a highly efficient NP-CQD adsorbent for organic dye degradation by adsorption.

The relative dominance of surface oxygen content over pore properties in controlling adsorption and retrograde behavior of gaseous toluene over microporous carbon

The adsorption potential of activated carbon (AC) derived from macadamia nut shells (product code of Procarb-900: namely, AC-P) has been investigated using gaseous toluene as the target pollutant. The powder AC-P with high-microporosity (96%) and oxygen content (5.62%) exhibited very high adsorption capacity (214 mg·g-1) and partition coefficient (PC: 25 mol·kg-1·Pa-1) against 100 ppm (10 Pa) toluene at 99% breakthrough levels (1 atm dry N2). The factors governing toluene adsorption were explored with respect to the key variables such as surface functional groups, pore size distribution, sorbent bed mass (50, 100, and 150 mg), and particle size (i.e., 0.212-0.6 mm (powder AC: PAC)) vs. 0.6-2.36 mm (granular AC: GAC)). Accordingly, the adsorption process was physical, mainly due to the non-polar interactions (i.e., π-π interactions) between the adsorbent and adsorbate molecules. The high affinity of AC-P at low breakthrough levels was obtained through a combination of smaller particle size (PAC) and larger adsorbent mass (i.e., 150 mg) with the appearance of a very pronounced retrograde phenomenon (e.g., at < 1% breakthrough level). As such, toluene adsorption appeared to be affected more sensitively by particle size and adsorbent mass (especially at low breakthrough levels) than by high microporosity. Most importantly, the oxygen content of AC emerges as one of the key factors governing the maximum capacity, as the changes in pore volume are not crucial to explain the observed adsorption patterns of toluene.

Diaminopropane-appended activated carbons for the adsorptive removal of gaseous formaldehyde using a portable indoor air purification unit

It is of significant practical interest to develop high-performance air purifier (AP) for removing carcinogenic volatile organic compounds present ubiquitously in indoor air (e.g., formaldehyde (FA)). In this regard, a portable AP system was designed by loading honeycomb ceramic filters with diaminopropane (DAP)-appended activated carbon (AC). The maximum removal efficiencies (REs) of AP loaded with 10, 20, 30, and 50 %-DAP/AC were 26.2, 28, 88.3, and 89.4 %, respectively, against 5 ppm FA (at 160 L min-1). Hence, the 30 % DAP unit was used mainly in this work. The removal efficiency of 30 %-DAP/AC (160 L min-1), when tested against 2 ppm FA, decreased from 90.3 to 73.2 % with an increase in relative humidity from 0 to 60 %. The performance of the AP unit, when assessed kinetically in terms of the clean air delivery rate (CADR), reached as high as 10.2 L min-1 at the flow rate of 160 L min-1. Isotherm analysis further demonstrated the complex multilayered adsorption behavior of FA. Based on the density functional theory (DFT) simulation, the superiority of DAP/AC for FA adsorption can be attributed to the synergy of covalent (chemisorption) and non-covalent (pore filling and film diffusion) interactions.

Photocatalytic Degradation of Gaseous Benzene Using Cu/Fe-Doped TiO2 Nanocatalysts under Visible Light

Visible-light-enhanced TiO2 nanocatalysts doped with Cu and Fe were synthesized using the sol-gel method to investigate their performance in degrading gaseous benzene. The structure and morphology of mono- and co-doped TiO2 (i.e., Cu/Fe-TiO2, Cu-Fe-TiO2) were characterized using SEM, EDS, XRD, BET, Raman, UV-vis-DRS, and XPS techniques. The results indicated that the presence of Cu/Fe mono- and co-doped TiO2 leads to the formation of an anatase phase similar to pure TiO2. Furthermore, the introduction of Cu/Fe enhanced the presence of lattice defects and increased the specific surface area of TiO2. This enhancement can be attributed to the increase in oxygen vacancies, especially in the case of Cu-Fe-TiO2. Additionally, Cu-Fe-TiO2 showed a higher concentration of surface-bound hydroxyl groups/chemically adsorbed oxygen and a narrower bandgap than pure TiO2. Consequently, Cu-Fe-TiO2 exhibited the highest photocatalytic performance of 658.33 μgC6H6/(g·h), achieving a benzene degradation rate of 88.87%, surpassing that of pure TiO2 (5.09%), Cu-TiO2 (66.92%), and Fe-TiO2 (59.99%). Reusability tests demonstrated that Cu-Fe-TiO2 maintained a high benzene degradation efficiency of 71.4%, even after five experimental cycles, highlighting its exceptional stability and reusability. In summary, the addition of Cu/Fe to TiO2 enhances its ability to degrade gaseous benzene by prolonging the catalyst's lifespan and expanding its photoresponse range to include visible light.