Cu(II)-EDTA removal by a two-step Fe(0) electrocoagulation in near natural water: Sequent transformation and oxidation of EDTA complexes

Autocatalytic degradation of Cu-EDTA in the Calcite/PMS system: Singlet oxygen and Cu(III)

The simultaneous removal of heavy metal complexes (HMCs) and heavy metal ions presents a significant challenge in treating wastewater. To address this, we propose a Calcite/Peroxymonosulfate (Calcite/PMS) system aimed at simultaneously decomplexing Cu-EDTA and removing Cu ions. Calcite/PMS system could achieve 99.5 % Cu-EDTA decomplexation and 61.9 % Cu ions removal within 60 min under initial conditions of Cu-EDTA (10 mg/L), Calcite (3 g/L), and PMS (2 mM). Singlet oxygen (1O2) emerged as the predominant reactive species responsible for Cu-EDTA decomplexation, which selectively targeted the N-C bonds in the Cu-EDTA structure to produce intermediates with lower biotoxicity than EDTA. Interestingly, solid phase Cu(III) (≡Cu(III)) promoted the generation of superoxide radicals (O2•-) with a contribution of up to 72.8 %. Subsequently, nascent ≡Cu(III) and O2•- accelerated the degradation of intermediates. Besides, coexisting organic substances inhibited Cu-EDTA decomplexation, whereas inorganic ions had a weak impact. After five cycles of use, the Calcite/PMS system retained 99.3 % efficiency in decomplexing Cu-EDTA. This investigation provides valuable insights into using calcite to remove HMCs and enhances our comprehension of the decomplexation intermediates accelerating HMCs degradation.

Ball-milled zero-valent iron with formic acid for effectively removing Cu(II)-EDTA accomplished by EDTA ligands oxidative degradation and Cu(II) removal

Heavy metal complexes in industrial wastewater are challenging to be removed by conventional methods arising from their stable chelating structure. In this study, zero-valent iron (ZVI) was ball-milled with tiny formic acid (FA), and the as-prepared sample (FA-ZVIbm) was attempted to eliminate a model heavy metal complex of Cu(II)-ethylenediaminetetraacetic acid (Cu(II)-EDTA). The addition of FA to ball-milling could dramatically enhance the performance of ball-milled ZVI (ZVIbm) towards Cu(II)-EDTA removal and increase the removal rate constant by 80 times. This conspicuous improvement of Cu(II)-EDTA elimination was attributed to the ferrous formate (Fe(HCOO)2) shell formed on the surface of FA-ZVIbm. Results revealed that the Fe(HCOO)2 shell facilitated the activation of O2 to reactive oxygen species (ROS) and the leaching of Fe3+. Cu(II)-EDTA was decomplexed through both oxidative destruction and Fe3+ replacement, and the released Cu2+ was reduced by FA-ZVIbm and immobilized synchronously. Meanwhile, the ligands underwent oxidative degradation by ROS, thus avoiding the re-chelation ecological risk. Impressively, FA-ZVIbm could achieve cyclic treatment of actual copper complex wastewater and possessed promising advantage in treatment cost. This study would offer a promising approach for eliminating Cu(II)-EDTA through EDTA ligands degradation and synchronous Cu(II) removal, moreover to shed light on the decomplexation mechanism.

Anoxic iron electrocoagulation automatically modulates dissolved oxygen and pH for fast reductive decomplexation and precipitation of Cu(II)-EDTA: The critical role of dissolved Fe(II)

Fe-based replacement and precipitation are promising methods for removal of copper ethylenediaminetetraacetic acid (Cu(II)-EDTA) but are limited by the necessity of controlling pH and dissolved oxygen. The details of the decomplexation mechanism also remain unclear. The present work investigated an anoxic iron electrocoagulation process capable of automatically modulating anoxic conditions and solution pH during exposure to air and thus promoting the rapid and thorough decomplexation of Cu(II)-EDTA. Dissolved Fe (II), rather than Fe(II)-bearing minerals, was found to be primarily responsible for the reduction of Cu(II)-EDTA to Cu(I)-EDTA and for the subsequent replacement reaction to generate free Cu(I) ions within the initial pH range of 2-7. The Cu(I) was primarily precipitated as Cu₂O on the surface of green rust and magnetite as the pH was increased. The aeration of these Fe-containing precipitates released free Cu(I) ions instead of chelated Cu into solution, allowing for recycling of the Cu. This release of Cu(I) was likely induced by the pH decrease during aeration. This study provides important insights regarding the reductive decomplexation of chelated Cu(II) and the recovery of Cu via anoxic iron electrocoagulation, which is a promising green approach to recycling Cu from wastewater.

Evaluation of photodegradation performance by paper microzones

Currently, the performance evaluation of catalysts usually requires expensive instruments. Hence, it is imperative to develop an alternative, green and sustainable method to investigate the photocatalytic reaction processes. Herein, the variation of degradation performance of different wastewaters with different dosage of P25 TiO₂ was evaluated to verify the reliability of the paper microzones method (PMZs). The optimum P25 TiO₂ dosage of 1 g/L for the degradation of methylene blue (MB) (UV light for 6 mins) and 0.5 g/L for the degradation of fuchsin basic (FB) (UV light for 5 mins) was obtained by the PMZs method. For the photocatalytic degradation of trivalent iron ion complexed salicylic acid (Fe(III)-SA) solution, the R² values of 0.904 and 0.801 were obtained for the photocatalytic reaction kinetics by PMZs and spectrophotometry, respectively, which again indicated the high reliability of PMZs. The accuracy of the results obtained by PMZs method relative to the spectrophotometric method ranged from 68.80% to 87.54% when degrading MB, FB, mixture of MB and FB, and Fe(III)-SA by P25 TiO₂. Therefore, the PMZs method is all in line with the requirements of low-carbon environmental protection and green chemistry, and has broad application prospects in the future.

The treatment of electroplating wastewater using an integrated approach of interior microelectrolysis and Fenton combined with recycle ferrite

Heavy metal ions in chelated forms have aroused great concerns because of their high solubility, poor biodegradation and extreme stability. In this research, an efficient strategy, interior microelectrolysis-Fenton-recycle ferrite (IM-Fenton-RF), was developed to treat simulated electroplating wastewater containing chelated copper at room temperature. The decomplexation of chelated copper was carried out by both interior microelectrolysis and Fenton reactions. IM process can not only partly degrade the complexes of chelated copper via the microelectrolysis reaction but also it produces Fe²⁺ ions for the Fenton reaction. After decomplexation, the IM-Fenton effluent directly flowed into the RF reactor for copper ions removal. Under optimum reaction conditions (reflux ratio = 0.37, Fe²⁺ concentration = 9.20 g/L at pH 10.18), 99.9% copper was removed by the IM-Fenton-RF system. The produced IM-Fenton-RF sludge is based on ferrite precipitate and has several advantages over metal hydroxides sludge. Ferrite sludge is stable owing to the stability of ferrite's crystal structure, while the toxicity characteristic leaching procedure (TCLP) test meets relevant standards. The sedimentation rate and volume of ferrite sludge were 3.86 times faster and 11.0 times lower than those of metal hydroxides sludge. Furthermore, the yielding sludge of ferrite can be recovered and utilized for the synthesis of Fe-C metallic species, the main compound of IM packing for interior microelectrolysis reaction. All these results show that a combination of IM-Fenton and RF is an effective approach to treat wastewater containing chelated copper, showing great potential for industrial applications.

Evaluating TiO2 Photocatalysis Performance in Microtubes on Paper Background by Smartphone: Principles and Application Examples

Titanium dioxide (TiO2) photocatalysis is a popular and promising technology in water treatment, but the performance evaluation usually depends on expensive equipment. In this study, using a smartphone for colorimetric detection, a self-invented method based on paper and microtubes (PMTs) is proposed to test the photocatalytic performance of TiO2. Firstly, the study has identified that PMTs achieved a correlation coefficient of above 0.9 between the greyscale values and concentrations during the physical process of different color dyes (i.e., rhodamine B (RhB), reactive yellow (RY), methylene blue (MB), and mixtures of the two or three dyes). The results indicate that when the principle of solution color follows the CMYK (Cyan, Magenta, Yellow, Black) color model, its photo color on white paper background conforms to the RGB (Red, Green, Blue) color model. Compared to the results obtained from the absorbance method, the PMTs method showed high reliabilities up to 99.36% on the monitoring of the photocatalytic process of the different dye solutions. Interestingly, the colorless solution of salicylic acid (SA) could also be analyzed by the PMTs after complexed with Fe(III) ion to develop a purple solution. These results suggest that the PMTs could be an alternative analysis method to evaluating physical and chemical reaction processes when the high-tech analysis equipment is unviable.