Zn-CNTs-Cu catalytic in-situ generation of H2O2 for efficient catalytic wet peroxide oxidation of high-concentration 4-chlorophenol

Catalytic air oxidation of biogas slurry using Cu sub-nanocluster supported by mesoporous TiZrO4 and protected by SiO2 shell

Biogas slurry, an inevitable outcome of anaerobic digestion (AD), is a treatment burden for urban environmental management. In this study, two kinds of biogas slurry (slurry J and slurry C), collected from the AD plants in Japan and China, were treated using novel TiZrO4 @Cu and TiZrO4 @Cu@SiO2 multilayered hollow spheres containing Cu sub-nanoclusters as the catalyst. The results showed that the chemical oxygen demand (COD) was removed by 63 % for slurry J and 44 % for slurry C after 5 h. The Cu sub-nanoclusters acted as co-catalysts and active centers, facilitating rapid electron transfer to oxygen molecules and forming highly reactive •O2- and •OH species (Use slurry J as the based solution). These free radicals cleaved the interconnecting bonds between benzene rings, disintegrated the ring structure, formed intermediate compounds such as n-hexylic acid, and ultimately mineralized organic pollutants in biogas slurry into CO2 and H2O. At the same time, TiZrO4 @Cu@SiO2 had excellent stability due to the protection of the SiO2 shell and reduced threefold Cu leaching than TiZrO4 @Cu. The COD removal rate was always 60 % in six cycles in the slurry J. The new catalyst ensured the high performance of catalytic air oxidation at low temperatures, which has significant potential as an environmentally friendly and energy-saving method for organic wastewater treatment.

Wet peroxide oxidation process catalyzed by Cu/Al2O3: phenol degradation and Cu2+ dissolution behavior

Catalytic wet peroxide oxidation (CWPO) has become an important deep oxidation technology for organics removal in wastewater treatments. Supported Cu-based catalysts belong to an important type of CWPO catalyst. In this paper, two Cu catalysts, namely, Cu/Al2O3-air and Cu/Al2O3-H2 were prepared and evaluated through catalytic degradation of phenol. It was found that Cu/Al2O3-H2 had an excellent catalytic performance (TOC removal rate reaching 96%) and less metal dissolution than the Cu/Al2O3-air case. Moreover, when the organic removal rate was promoted at a higher temperature, the metal dissolution amounts was decreased. Combined with hydroxyl radical quenching experiments, a catalytic oxidation mechanism was proposed to explain the above-mentioned interesting behaviors of the Cu/Al2O3-H2 catalyst for CWPO. The catalytic test results as well as the proposed mechanism can provide better guide for design and synthesis of good CWPO catalysts.

Catalytic Hydrodechlorination of 4-Chlorophenol by Palladium-Based Catalyst Supported on Alumina and Graphene Materials

Hydrodechlorination (HDC) is a reaction that involves the use of hydrogen to cleave the C-Cl bond in chlorinated organic compounds such as chlorophenols and chlorobenzenes, thus reducing their toxicity. In this study, a palladium (Pd) catalyst, which is widely used for HDC due to its advantageous physical and chemical properties, was immobilized on alumina (Pd/Al) and graphene-based materials (graphene oxide and reduced graphene oxide; Pd/GO and Pd/rGO, respectively) to induce the HDC of 4-chlorophenol (4-CP). The effects of the catalyst dosage, initial 4-CP concentration, and pH on 4-CP removal were evaluated. We observed that 4-CP was removed very rapidly when the HDC reaction was induced by Pd/GO and Pd/rGO. The granulation of Pd/rGO using sand was also investigated as a way to facilitate the separation of the catalyst from the treated aqueous solution after use, which is to improve practicality and effectiveness of the use of Pd catalysts with graphene-based support materials in an HDC system. The granulated catalyst (Pd/rGOSC) was employed in a column to induce HDC in a continuous flow reaction, leading to the successful removal of most 4-CP after 48 h. The reaction mechanisms were also determined based on the oxidation state of Pd, which was observed using X-ray photoelectron spectroscopy. Based on the results as a whole, the proposed granulated catalyst has the potential to greatly enhance the practical applicability of HDC for water purification.

Achieving High-Efficient Photoelectrocatalytic Degradation of 4-Chlorophenol via Functional Reformation of Titanium-Oxo Clusters

Rational design of crystalline catalysts with superior light absorption and charge transfer for efficient photoelectrocatalytic (PEC) reaction coupled with energy recovery remains a great challenge. In this work, we elaborately construct three stable titanium-oxo clusters (TOCs, Ti₁₀Ac₆, Ti₁₀Fc₈, and Ti₁₂Fc₂Ac₄) modified with a monofunctionalized ligand (9-anthracenecarboxylic acid (Ac) or ferrocenecarboxylic acid (Fc)) and bifunctionalized ligands (Ac and Fc). They have tunable light-harvesting and charge transfer capacities and thus can serve as outstanding crystalline catalysts to achieve efficient PEC overall reaction, that is, the integration of anodic organic pollutant 4-chlorophenol (4-CP) degradation and cathodic wastewater-to-H₂ conversion. These TOCs can all exhibit very high PEC activity and degradation efficiency of 4-CP. Especially, Ti₁₂Fc₂Ac₄ decorated with bifunctionalized ligands exhibits better PEC degradation efficiency (over 99%) and H₂ generation than Ti₁₀Ac₆ and Ti₁₀Fc₈ modified with a monofunctionalized ligand. The study of the 4-CP degradation pathway and mechanism revealed that such better PEC performance of Ti₁₂Fc₂Ac₄ is probably due to its stronger interactions with the 4-CP molecule and better ^•OH radical production. This work not only presents the effective combination of organic pollutant degradation and simultaneously H₂ evolution reaction using crystalline coordination clusters as both anodic and cathodic catalyst but also develops a new PEC application for crystalline coordination compounds.

Complexation and degradation of tetracycline by activation of molecular oxygen with biochar-supported nano-zero-valent copper composite

Nano-zero-valent copper (nZVC) is a superior molecular oxygen (O₂) activator for the abatement of organic pollutants due to its high electron utilization rate. However, the activation efficiency of O₂ is compromised by the agglomeration tendency of nZVC particles and the concomitant reduction of the available active sites. To address this problem, the biochar (BC) with porous structure and abundant surface functional groups is utilized to disperse and stabilize nZVC for O₂ activation (simplified as the nZVC/BC/O₂ system) for efficient removal of tetracycline (TC). The nZVC/BC composite possesses a high specific area with well-distributed nZVC particles on the BC surface, which guarantees the superior dispersion and high reactivity in the activation of O₂. The efficacy of the nZVC/BC/O₂ system for TC abatement is evaluated and the underlying mechanism is elucidated. The results show that nZVC/BC/O₂ system can achieve excellent removal of TC with the efficiencies of more than 85% in the pH range of 4.0-9.0, which originated from the combined action of complexation and degradation. The degradation is dominated by reactive oxygen species (ROS) including •OH, •O₂^- and ¹O₂ generated by Cu⁰/Cu⁺ activated O₂ while the generation of Cu²⁺ via oxygen oxidation on the surface of nZVC/BC can remove TC by complexation adsorption. This study highlights the complexation and degradation in the removal of TC and can be expected to exhibit application prospects in the water and wastewater treatment.

Nano-CuOx for ciprofloxacin effective removal via wet peroxide oxidation catalysis and its practical application in wastewater

Using Cu(NO3)2·3H2O as active material and citric acid (CA) as complexing agent, heterogeneous catalyst nano-CuOx was prepared by sol-gel method. The catalytic wet peroxide oxidation (CWPO) reaction system was established accordingly. The system was used to treat ciprofloxacin (CIP) in simulated wastewater and real wastewater. The effects of the molar ratio of metal salt to CA, calcination temperature, H2O2 dosage, reaction temperature, and catalyst dosage on the physicochemical structure and the properties of CWPO were investigated. The results showed that when the molar ratio of CA to metal salt (Cu(NO3)2·3H2O) was 1.8, the calcination temperature was 500 °C, the concentration of H2O2 was 10 mmol · L–1, the reaction temperature was 95 °C, and the dosage of catalyst was 1 g · L–1, CWPO system has the best degradation effect on CIP. At thses optical conditions, the removal rate reached 86.8%, chemical oxygen demand (COD) removal rate reached 54.9%, and the recycling rate of the catalyst was very good. The refractory organics in actual pharmaceutical wastewater could be oxidized by this system as well, and the COD removal rate reaches 47%. The degradation mechanism of CIP showed that the main functions of the CWPO system were ·O2– and ·OH radicals. The possible degradation pathways were determined by ion chromatography to be intermediate products generated from piperazine ring cleavage, defluorination, decarboxylation, and quinoline hydroxylation of CIP. The catalyzing mechanism was investigated in detail; some useful information was obtained in this work.

An Evaluation of the Kinetic Properties Controlling the Combined Chemical and Biological Treatment of Toxic Recalcitrant Organic Compounds from Aqueous Solution

Due to their high toxicity, propensity for cancer, teratogenicity, mutagenicity, and genotoxicity, hazardous water-soluble phenolic compounds must be controlled immediately. In this study, a model was created to simulate the degradation of harmful recalcitrant organic compounds in a combined chemical and biological treatment system. The parameter estimations with inhibition coefficient (Haldane model) and without inhibition coefficient (Michaelis-Menten model) were assessed over a wide range of initial concentrations using the Monod-like model. The kinetic parameters were optimized using AQUASIM 2.0 software. At a 50 mgL−1 feed concentration of 4-chlorophenol, removal efficiencies of more than 98% were attained under these circumstances. The primary kinetic parameters were identified and their values models were validated using the fitted parameter values that reached a good degree of agreement (R2 = 0.998). We may better comprehend and make use of the complex phenolic compounds’ biodegradation processes, such as progress optimization and scale-up, by understanding the mechanisms of substrate interaction and the new kinetic models that have been provided in this work.

Analysis of the degradation of m-cresol with Fe/AC in catalytic wet peroxide oxidation enhanced by swirl flow

Catalytic wet peroxide oxidation (CWPO) enhanced by swirl flow (SF-CWPO) was developed for the first time to explore the degradation of m-cresol in 3%iron/activated carbon catalysed Fenton reaction. Under the conditions of catalyst dosage of 0.6 g/L, H₂O₂ dosage of 1.5 mL/L, pH = 6 and reaction time of 20 min, the degradation rate of m-cresol and total organic carbon in 100 mg/L m-cresol solution reaches 81.5% and 82%, respectively. The reaction speed in the SF-CWPO system with an independently designed cyclone reactor was two times faster than the traditional CWPO systems. In addition, via liquid chromatography-mass spectrometry analysis of the degradation product, the possible degradation pathway for m-cresol was proposed. The proposed SF-CWPO can potentially be an efficient and economical method to treat organic pollutants in wastewaters.

Performance of high temperature phase-stable high entropy oxide (MgCuMnCoFe)O x in catalytic wet air oxidation of chloroquine phosphate

With the continuous spread of COVID-19, the water pollution problems caused by the abuse of chloroquine phosphate (CQP) as an antiviral drug have attracted wide attention. The cubic Fm-3m spinel high entropy oxide (HEO)-(MgCuMnCoFe)O _x was prepared by coprecipitation method as the catalytic wet air oxidation (CWAO) catalyst to treat CQP simulated wastewater. Through electron spin resonance (ESR) analysis, HEO will stimulate the production of superoxide radical (·O₂ ^-) and hydroxyl radical (·OH) in the wet air oxidation (WAO) process, which accelerates the degradation and mineralization of CQP. Through response surface method (RSM) optimization, the optimal degradation conditions of CQP in CWAO were proposed: initial oxygen pressure of 15 bar, catalyst dosage of 1.4 g/L and temperature of 230 °C. The advantages of HEO in CWAO were analyzed by principal component analysis (PCA). The degradation mechanism of CQP in CWAO by (MgCuMnCoFe)O _x were explored. This work provides a new idea for the rapid development of HEO in the field of environmental catalysis.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s10853-022-07271-z.

Modification of structured bio‑carbon derived from spongin-based scaffolds with nickel compounds to produce a functional catalyst for reduction and oxidation reactions: Potential for use in environmental protection

Three different 3D fibrous-like NiO/Ni(OH)₂/Ni‑carbonized spongin-based materials were prepared via a simple sorption-reduction method. Depending on the support used, the catalysts were composed of carbon, nickel oxide, nickel hydroxide and zero-valent nickel, with the surface content of the nickel-containing phase in the range 15.2-26.0 wt%. Catalytic studies showed promising activity in the oxidation of phenolic compounds in water and in the reduction of 4-nitrophenol. The oxidation efficiency depends on the substrate used and ranges from 80% for phenol at pH 2 to 99% for 4-chlorophenoxyacetic acid (4-CPA) and methylchlorophenoxypropionic acid (MCPP). In the reduction reaction, all catalysts exhibited superior activity, with rate constants in the range 0.648-1.022 min^-1. The work also includes a detailed investigation of reusability and kinetic studies.

An overview on non-spherical semiconductors for heterogeneous photocatalytic degradation of organic water contaminants

Because of their carcinogenicity and mutagenicity, the elimination of organic contaminants from surface and subsurface water is a subject of environmental significance. Conventional water decontamination approaches such as membrane separation, ultrafiltration, adsorption, reverse osmosis, coagulation, etc., have relatively higher operating costs and can generate highly toxic secondary contaminants. On the other hand, heterogeneous photocatalysis, an advanced oxidation process (AOP), is considered a clean and cost-effective process for organic pollutants degradation. Owing to their distinctive structure and physicochemical properties non-spherical semiconductors have gained considerable limelight in the photocatalytic degradation of organic contaminants. The current review briefly introduces a wide range of organic water contaminants. Recent advances in non-spherical semiconductor assembly and their photocatalytic degradation applications are highlighted. The underlying mechanism, fundamentals of photocatalytic reactions, and the factors affecting the degradation performance are also alluded including the current challenges and future research perspectives.

Highly Efficient Degradation of Persistent Pollutants with 3D Nanocone TiO2-Based Photoelectrocatalysis

Photoelectrocatalytic (PEC) degradation of organic pollutants into CO₂ and H₂O is a promising strategy for addressing ever-growing environmental problems. Titanium dioxide (TiO₂) has been widely studied because of its good performance and environmental benignancy; however, the PEC activity of TiO₂ catalyst is substantially limited due to its fast electron-hole recombination. Herein, we report a TiO₂ nanocone-based photoelectrocatalyst with superior degradation performance and outstanding durability. The unique conical catalyst can boost the PEC degradation of 4-chlorophenol (4-CP) with 99% degradation efficiency and higher than 55% mineralization efficiency at a concentration of 20 ppm. The normalized apparent rate constant of a nanocone catalyst is 5.05 h^-1 g^-1 m², which is 3 times that of a nanorod catalyst and 6 times that of an aggregated particle catalyst, respectively. Further characterizations reveal that the conical morphology of TiO₂ can make photogenerated charges separate and transfer more efficiently, resulting in outstanding PEC activity. Moreover, computational fluid dynamics simulations indicate that a three-dimensional conical structure is beneficial for mass transfer. This work highlights that tuning the morphology of a photoelectrocatalyst at the nanometer scale not only promotes the charge transfer but also facilitates the mass transportation, which jointly enhance the PEC performance in the degradation of persistent pollutants.

Complete solar-driven dual-photoelectrode fuel cell for water purification and power generation in the presence of peroxymonosulfate

This study reports the development of complete solar-driven dual-photoelectrode fuel cell (PFC) based on WO₃ photoanode and Cu₂O photocathode with peroxymonosulfate (PMS) serving as cathodic electron acceptor. As indicated by photoelectrochemical measurements, the PMS was able to improve thermodynamic properties of photocathode, achieving an increased open circuit potential from 0.42 V to 0.65 V vs standard hydrogen electrode (SHE). Under simulated sunlight irradiation (~100 mW cm^-2), the maximum power density of 0.12 mW cm^-2 could be obtained at current density of 0.34 mA cm^-2, which was 8.57 times of that produced by PFC without PMS (0.014 mW cm^-2). Correspondingly, adding PMS (1.0 mM) increased overall removal efficiency of 4-chlorophenol (4-CP) from 39.8% to 96.8%, accounting for the first-order kinetic constant (k=0.056 min^-1) being 6.67 times of that in the absence of PMS (k=0.0084 min^-1). Radical quenching and electron spin-resonance (ESR) results suggested the contribution of free radicals (•OH and SO₄^•-) and non-radical pathway associated with direct activation of PMS by Cu₂O photocathode. Fourier transformed infrared (FTIR) analysis confirmed the strong non-radical interaction between Cu₂O photocathode and PMS, resulting in 4-CP removal via activation of PMS by surface complex on Cu₂O. The proof-in-concept complete solar-driven dual-photoelectrode fuel cell may offer an effective manner to realize water purification and power generation, making wastewater treatment more economical and more sustainable.