Selective adsorption and enhanced photodegradation of diclofenac in water by molecularly imprinted TiO2

Bi-functional NiFe2O4/SrTiO3 S-scheme heterojunction for eminent performance photocatalytic treatment of sewage effluent and electrochemical hydrazine determination

Devising of materials that afforded dual applicability in decontamination and pollutant detection were still a towering challenge owing to the increasing flux of discharge toxic contaminants over the years. Herein, the NiFe2O4 nanoparticles-loaded on cube-like SrTiO3 (NiFe2O4/SrTiO3) composite was fabricated by a two-step hydrothermal approach providing remarkable photocatalytic treatment and electrochemical sensing of noxious pollutants in wastewater. The material traits of the fabricated composite were scrutinized by myriad characterization approaches. The NiFe2O4/SrTiO3 hybrid material demonstrated high surface area of 19.81 m2/g, adequate band gap energy of 2.75 eV, and prominent photoluminescence characteristics. In the presence of visible light, the NiFe2O4/SrTiO3 exhibited profound photocatalysis capability to eliminate sewage effluent-bearing chlortetracycline hydrochloride (CTCH) with 88.6% COD removal in 120 min, outperforming other pure materials. Meanwhile, the toxicity examination of effluent, the possible degradation pathway of CTCH and the proposed photocatalysis mechanism were also divulged. More importantly, the glassy carbon electrode was modified with synergized NiFe2O4/SrTiO3 (NiFe2O4/SrTiO3-GCE) was adopted for the precise quantification of Hydrazine (Hz). The NiFe2O4/SrTiO3-GCE obeyed first-order response for the Hz detection within the range of 1-10 mM: cyclic voltametric: limit of detection (LOD) of 0.119 μM with sensitivity of 18.9 μA μM-1 cm-2, and linear sweep voltametric: LOD of 0.222 μM with a sensitivity of 12.05 μA μM-1 cm-2. The stability and interference of modified electrode were also inspected. This work furnished valuable insights to yield a composite with the prominent S-scheme heterojunction system for quenching of charge carrier recombination and consequently contributing to the future realization into the domains of environmental clean-up and toxic chemical detection.

Molecularly Imprinted Heterostructure-Assisted Laser Desorption Ionization Mass Spectrometry Analysis and Imaging of Quinolones

Quinolone residues resulting from body metabolism and waste discharge pose a significant threat to the ecological environment and to human health. Therefore, it is essential to monitor quinolone residues in the environment. Herein, an efficient and sensitive matrix-assisted laser desorption/ionization mass spectrometry (MALDI/MS) method was devised by using a novel molecularly imprinted heterojunction (MIP-TNs@GCNs) as the matrix. Molecularly imprinted titanium dioxide nanosheets (MIP-TNs) and graphene-like carbon nitrides (GCNs) were associated at the heterojunction interface, allowing for the specific, rapid, and high-throughput ionization of quinolones. The mechanism of MIP-TNs@GCNs was clarified using their adsorption properties and laser desorption/ionization capability. The prepared oxygen-vacancy-rich MIP-TNs@GCNs heterojunction exhibited higher light absorption and ionization efficiencies than TNs and GCNs. The good linearity (in the quinolone concentration range of 0.5-50 pg/μL, R2 > 0.99), low limit of detection (0.1 pg/μL), good reproducibility (n = 8, relative standard deviation [RSD] < 15%), and high salt and protein resistance for quinolones in groundwater samples were achieved using the established MIP-TNs@GCNs-MALDI/MS method. Moreover, the spatial distributions of endogenous compounds (e.g., amino acids, organic acids, and flavonoids) and xenobiotic quinolones from Rhizoma Phragmitis and Rhizoma Nelumbinis were visualized using the MIP-TNs@GCNs film as the MALDI/MS imaging matrix. Because of its superior advantages, the MIP-TNs@GCNs-MALDI/MS method is promising for the analysis and imaging of quinolones and small molecules.

Study on the preparation of molecularly imprinted ZrO2-TiO2 photocatalyst and the degradation performance of hydroquinone

In this paper, molecularly imprinted Zr-doped TiO2 photocatalysts (MIP-ZrO2-TiO2) were prepared by the molecularly imprinted sol-gel method for the photocatalytic degradation study of hydroquinone (HQ) as the target pollutant. For the effectiveness of the MIP-ZrO2-TiO2 catalyst in degrading HQ, the effects of Zr doping ratio, imprinted molecule dosage, calcination conditions, and pollutant concentration on its photocatalytic activity were investigated. XRD, TEM, XPS, and other techniques were used to evaluate the materials, and the findings revealed that MIP-ZrO2-TiO2 films with imprinted HQ were successfully produced on the ZrO2-TiO2 surface. The optimal preparation conditions were n(Ti):n(Zr) = 100:8, m(HQ) = 1.5 g, 550 °C for the calcination temperature, and 2 h for the calcination duration. The optimum reaction conditions were 10 mg/L HQ concentration, 1 g/L catalyst dose, and a pH of 6.91. According to the findings of photocatalytic tests, during 30 min of UV lamp (365 nm) irradiation, the degradation rates of MIP-ZrO2-TiO2, ZrO2-TiO2, and TiO2 for HQ were 90.58%, 83.94%, and 58.30%, respectively. The findings revealed that the doping of Zr metal and the addition of imprinted molecules improved the photocatalytic activity of TiO2, which can be used for the efficient treatment of low concentrations of hard-to-degrade hydroquinone.

Shaddock peel-derived N-doped carbon quantum dots coupled with ultrathin BiOBr square nanosheets with boosted visible light response for high-efficiency photodegradation of RhB

In the present work, we constructed a serials of novel shaddock peel-derived N-doped carbon quantum dots (NCQDs) coupled with BiOBr composites. The result showed that the as-synthesized BiOBr (BOB) was composed of ultrathin square nanosheets and flower-like structure, and NCQDs were uniformly dispersed on the surface of BiOBr. Furthermore, the BOB@NCQDs-5 with optimal NCQDs content displayed the top-flight photodegradation efficiency with ca. 99% of removal rate within 20 min under visible light and possessed excellent recyclability and photostability after 5 cycles. The reason was attributed to relatively large BET surface area, the narrow energy gap, inhibited recombination of charge carriers and excellent photoelectrochemical performances. Meanwhile, the improved photodegradation mechanism and possible reaction pathways were also elucidated in detail. On this basis, the study opens a novel perspective to obtain a highly efficient photocatalyst for practical environment remediation.

Recent advances in nanomaterials based sustainable approaches for mitigation of emerging organic pollutants

Emerging organic pollutants (EOPs) are a category of pollutants that are relatively new to the environment and recently garnered a lot of attention. The majority of EOPs includes endocrine-disrupting chemicals (EDCs), antibiotic resistance genes (ARGs), pesticides, dyes and pharmaceutical and personal care products (PPCPs). Exposure to contaminated water has been linked to an increase in incidences of malnutrition, intrauterine growth retardation, respiratory illnesses, liver malfunctions, eye and skin diseases, and fatalities. Consequently, there is a critical need for wastewater remediation technologies which are effective, reliable, and economical. Conventional wastewater treatment methods have several shortcomings that can be addressed with the help of nanotechnology. Unique characteristics of nanomaterials (NMs) make them intriguing and efficient alternative in wastewater treatment strategies. This review emphasis on the occurrence of divers emerging organic pollutants (EOPs) in water and their effective elimination via different NMs based methods with in-depth mechanisms. Furthermore, it also delves the toxicity assessment of NMs and critical challenges, which are crucial steps for practical implementations.

Study on the photocatalytic properties differences between the 1-D and 3-D W18O49 particles†

The morphology of W₁₈O₄₉ catalysts has a significant effect on their photocatalytic performance. Herein, we successfully prepared two commonly used W₁₈O₄₉ photocatalysts just by changing the reaction temperature in the hydrothermal system, namely 1-D W₁₈O₄₉ nanowires (1-D W₁₈O₄₉) and 3-D urchin-like W₁₈O₄₉ particles (3-D W₁₈O₄₉), and evaluated the difference of their photocatalytic performances by taking the degradation of methylene blue (MB) as an example. Remarkably, 3-D W₁₈O₄₉ exhibited an impressive photocatalytic degradation performance towards MB with photocatalytic reaction rates of 0.00932 min⁻¹, which was about 3 times higher than that of 1-D W₁₈O₄₉. The comprehensive characterization and control experiments could further reveal that the hierarchical structure of 3-D W₁₈O₄₉ brought higher BET surface areas, stronger light harvesting, faster separation of photogenerated charges and so on, which was the main reason for its better photocatalytic performance. ESR results confirmed that the main active substances were superoxide radicals (˙O₂⁻) and hydroxyl radicals (˙OH). This work aims to explore the intrinsic relationship between the morphology and photocatalytic properties of W₁₈O₄₉ catalysts, so as to provide a theoretical basis in the morphology selection of W₁₈O₄₉ or its composite materials in the field of photocatalysis.

Comprehensive characterization and control experiments were used to deeply explore the intrinsic relationship between the morphology and photocatalytic properties of W₁₈O₄₉ catalysts.

Wetland plant-derived biochar enhances the diclofenac treatment performance in vertical subsurface flow constructed wetlands

Diclofenac (DFC) is a pharmacologically active compound frequently detected in various receiving waters. To improve the efficiency of constructed wetlands in removing DFC, biochar (BC) is added as a substrate. The study mainly involved the effect of adding wetland plant-derived BC to vertical subsurface flow constructed wetlands (VSF-CWs) on the DFC removal process. In addition, the study discussed the effects of the initial DFC concentration (0.05-1.00 mg L^-1), pH (5.5-8.5), and hydraulic retention times (HRTs, 1-7 d) on the removal process and fluctuations in the microbial community. Preliminary results of the study showed optimal removal (>90%) achieved at an initial DFC concentration of 0.75-1 mg L^-1, a pH of 6.5-7.5, and an HRT of 7 d. Moreover, no significant effects on the removal efficiency of conventional water quality parameters were observed. Non-metric multidimensional scaling results revealed a reshaped community structure, which was altered by the initial DFC concentration. DFC concentration is a key factor in the variation of microbial communities and controls the quantitative evolution of the species in experimental units. Therefore, the addition of BC to CWs effectively enhanced the removal efficiency of DFC and provided a viable and effective improvement of the CWs.

Preparation and Adsorption Properties of Magnetic Molecularly Imprinted Polymers for Selective Recognition of 17β-Estradiol

In this paper, magnetic molecularly imprinted polymers (MMIPs) were fabricated on the surface of Fe3O4 by surface molecular imprinting technology, which can selectively adsorb 17β-estradiol (E2). The optimized experiments demonstrated that MMIPs possessed the best adsorption capacity when methanol was used as the solvent and MAA was used as the crosslinking agent, with a molar ratio of E2: MMA: EGDMA as 1:4:50. SEM, FTIR, and XRD were employed to investigate the morphologies of MMIPs and the results demonstrated that the MMIPs that can selectively adsorb E2 were successfully prepared on Fe3O4 particles. The adsorption experiments showed that 92.1% of E2 was adsorbed by the MMIPs, which is higher than the magnetic non-molecularly imprinted polymers (MNIPs). The Freundlich isotherm model was more suitable to describe the adsorption process of E2 by MMIPs. Meanwhile, MMIPs had a better recognition ability for E2 and its structural analogs such as estrone and estriol. The MMIPs still had good adsorption performance after methanol regeneration five times. The prepared MMIPs had the advantages of efficient adsorption ability and high reusability, so they can be applied for selective recognition and removal of E2.

Study of Photocatalytic Oxidation of Micropollutants in Water and Intensification Case Study

During the last decades, heterogenous photocatalysis has shown as the most promising advanced oxidation process for the removal of micropollutants due to degradation rate, sustainability, non-toxicity, and low-cost. Synergistic interaction of light irradiation, photocatalysts, and highly reactive species are used to break down pollutants toward inert products. Even though titanium dioxide (TiO2) is the most researched photocatalyst, to overcome shortcomings, various modifications have been made to intensify photocatalytic activity in visible spectra range among which is modification with multiwalled carbon nanotubes (MWCNTs). Therefore, photocatalytic oxidation and its intensification by photocatalyst’s modification was studied on the example of four micropollutants (diclofenac, DF; imidacloprid, IMI; 1-H benzotriazole, BT; methylene blue, MB) degradation. Compound parabolic collector (CPC) reactor was used as, nowadays, it has been considered the state-of-the-art system due to its usage of both direct and diffuse solar radiation and quantum efficiency. A commercially available TiO2 P25 and nanocomposite of TiO2 and MWCNT were immobilized on a glass fiber mesh by sol-gel method. Full-spectra solar lamps with appropriate UVB and UVA irradiation levels were used in all experiments. Photocatalytic degradation of DF, IMI, BT, and MB by immobilized TiO2 and TiO2/CNT photocatalysts was achieved. Mathematical modelling which included mass transfer and photon absorption was applied and intrinsic reaction rate constants were estimated: kDF=3.56 × 10−10s−1W−0.5m1.5, kIMI=8.90 × 10−11s−1W−0.5m1.5, kBT=1.20 × 10−9s−1W−0.5m1.5, kMB=1.62 × 10−10s−1W−0.5m1.5. Intensification of photocatalysis by TiO2/CNT was observed for DF, IMI, and MB, while that was not the case for BT. The developed model can be effectively applied for different irradiation conditions which makes it extremely versatile and adaptable when predicting the degradation extents throughout the year using sunlight as the energy source at any location.

Toxicity Assessment and Treatment Options of Diclofenac and Triclosan Dissolved in Water

The presence of pharmaceutical and personal care products in water is increasing tremendously nowadays. Typical representatives are diclofenac (DCF) and triclosan (TCS). Acute toxicity of these substances was experimentally assessed using the freshwater algae Raphidocelis subcapitata (living, immobilized). The IC50 achieved for R. subcapitata was 177.7–189.1 mg·L−1 for DCF and 5.4–17.2 µg·L−1 for TCS, whereas, regarding DCF, the results corresponded to the values observed by other authors. Concerning TCS, the results were lower than predicted and indicated TCSs’ higher toxicity. The immobilized R. subcapitata showed comparable results with its living culture for DCF only. Regarding K2Cr2O7 and TCS, the immobilized alga was more sensitive. The DCF and TCF removal from water was tested by sorption, photocatalytic and photolytic processes. TiO2 was used as a photocatalyst. Norit and SuperSorbon were used as sorbents based on activated charcoal. The DCF decomposition achieved by both photo-processes was very fast. The starting concentration fell below the detection limit in less than one minute, while bioluminescence on Aliivibrio fischeri showed no toxic intermediates formed only in the case of photocatalysis. DCF and TCS removals by sorption were significantly faster on Norit than SuperSorbon, while the bioluminescence inhibition remained insignificant.

Influence of Impregnation Medium on the Adsorptive Performance of Silica Sulfuric Acid for the Removal of Gaseous o-Xylene: Comparison on Ethyl Acetate and Water

Silica supported sulfuric acid (SSA) has been demonstrated to be capable of effectively removing phenyl VOCs through the reaction-type adsorption mechanism. The effects of the solvent (water, ethyl acetate) used to impregnate silica gel with H2SO4 solution in order to prepare SSA adsorbents have been studied. As-prepared two series SSA(E)-x and SSA(W)-x materials (x = 1, 2, 3, 4) were characterized by TG, SEM/EDS and N2 adsorption/desorption techniques, and their breakthrough adsorption performances were evaluated from experimental and theoretical aspects. The results showed that the H2SO4 loading amounts were 2.8, 4.0, 4.8 and 5.6 mmol g−1 respectively for both SSA(E)-x and SSA(W)-x when x equaled 1, 2, 3, 4. Among them, SSA(E)-4 was found to have a higher proportion of the C-state H2SO4 than SSA(W)-4. Both SSA(E)-x and SSA(W)-x exhibited significant removal capacity of gaseous o-xylene. The reactive temperature regions were determined to be 120–170 °C for SSA(E)-4 and 120–160 °C for SSA(W)-4 with a common optimum point of 160 °C. Both SSA(E)-x and SSA(W)-x adsorbents exhibited excellent recyclability and reuse performance. Further, the series SSA(E)-x materials outperformed the series SSA(W)-x on all adsorption performance metrics, suggesting that ethyl acetate is a preferred solvent for preparing the SSA materials in phenyl VOCs removal application.

Multi-Responsive Optimization of Novel pH-Sensitive Hydrogel Beads Based on Basil Seed Mucilage, Alginate, and Magnetic Particles

Conventional drug delivery systems often cause side effects and gastric degradation. Novel drug delivery systems must be developed to decrease side effects and increase the efficacy of drug delivery. This research aimed to fabricate hydrogel beads for use as a drug delivery system based on basil seed mucilage (BSM), sodium alginate (SA), and magnetic particles (MPs). The Taguchi method and Grey relational analysis were used for the design and optimization of the hydrogel beads. Three factors, including BSM, SA, and MPs at four levels were designed by L-16 orthogonal arrays. BSM was the main factor influencing bead swelling, drug release rate at pH 7.4, and release of antioxidants at pH 1.2 and 7.4. In addition, SA and MPs mainly affected drug loading and drug release rate in acidic medium, respectively. Grey relational analysis indicated that the composition providing optimal overall properties was 0.2 vol% BSM, 0.8 vol% SA, and 2.25 vol% MPs. Based on the findings of this work, BSM/SA/MPs hydrogel beads have the potential to be used as a pH-sensitive alternative material for drug delivery in colon-specific systems.

In situ anchor of Na2Ti3O7 in nitrogen-rich carbon hollow red blood cell-like structure as a 0D-3D hierarchical electrode material for efficient electrochemical desalination

Reasonable design of the structure and complementary compounding of electrode materials is helpful to enhance capacitive deionization (CDI) performance. Herein, a novel 0D-3D hierarchical electrode material containing Na2Ti3O7 nanoparticles anchored at hollow red blood cell (HRBC)-like nitrogen-rich carbon (HRBC-NTO/N-C-60) was prepared via selective protection, pyrolysis, and alkalization. Specifically, a HRBC-like NH2-MIL-125-based material (HRBC-MOF-60) was first constructed by a selective protection approach of tannic acid (TN), which addresses the shortcomings of using sacrificial templates or corrosive agents. Afterwards, HRBC-NTO/N-C-60 was obtained in situ by annealing and alkalization of HRBC-MOF-60. The nitrogen-rich carbon with a HRBC-like structure has the ability to rapidly transport electrons, and its porous structure enables remarkable charge transfer. Benefiting from the grafted 3D N-doped porous carbon with a HRBC-like structure, well-dispersed 0D Na2Ti3O7 nanoparticles, and satisfactory bonding effects, HRBC-NTO/N-C-60 exhibited high specific capacitance and fast ionic and electronic diffusion kinetics. Moreover, HRBC-NTO/N-C-60 was well-suited for desalination by functioning as a cathode material for capacitive deionization (CDI), and delivering a high desalination capacity of 66.8 mg g-1 in 200 mg L-1 NaCl solution at 1.4 V. This work introduces an excellent high-performance candidate for electrochemical deionization as well as affording afflatus for accurately inventing OD-3D hierarchical materials with hollow structures.

Remediation of pharmaceuticals from contaminated water by molecularly imprinted polymers: a review

The release of pharmaceuticals into the environment induces adverse effects on the metabolism of humans and other living species, calling for advanced remediation methods. Conventional removal methods are often non-selective and cause secondary contamination. These issues may be partly solved by the use of recently-developped adsorbents such as molecularly imprinted polymers. Here we review the synthesis and application of molecularly imprinted polymers for removing pharmaceuticals in water. Molecularly imprinted polymers are synthesized via several multiple-step polymerization methods. Molecularly imprinted polymers are potent adsorbents at the laboratory scale, yet their efficiency is limited by template leakage and polymer quality. Adsorption performance of multi-templated molecularly imprinted polymers depends on the design of wastewater treatment plants, pharmaceutical consumption patterns and the population serviced by these wastewater treatment plants.

Promotion effect of free Ag+ ions on photocatalytic dechlorination processes

Free silver ions (Ag+) in the solution exhibit enhanced photocatalytic dechlorination processes of organic chloride, including 2-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol, over PhC2Cu under visible light irradiation.

Novel, Simple and Low-Cost Preparation of Ba-Modified TiO2 Nanotubes for Diclofenac Degradation under UV/Vis Radiation

A novel low-cost synthesis of barium-modified TiO2 nanotube (TNT) arrays was used to obtain an immobilized photocatalyst for degradation of diclofenac. TNT arrays were prepared by electrochemical anodization of titanium thin films deposited on fluorine-doped tin oxide (FTO) coated glass by magnetron sputtering, ensuring transparency and immobilization of the nanotubes. The Ba-modifications were obtained by annealing solutions of Ba(OH)2 spin coated on top of TNT. Three different concentrations of Ba(OH)2 were used (12.5 mM, 25 mM and 50 mM). The crystalline structure, morphology and presence of Ba were characterized by X-ray diffraction, scanning electron microscopy and energy dispersive X-ray spectroscopy, respectively. Ba-modified TiO2 nanotubes (BTNT) were tested for photocatalytic degradation of diclofenac under UV/Vis radiation and it was proven that all of the Ba-modified samples showed an increase in photocatalytic activity with respect to the unmodified TNTs. The most efficient photocatalyst was the sample prepared with 25 mM Ba(OH)2 which showed 90% diclofenac degradation after 60 min. This result was in agreement with cyclic voltammetry measurements that showed the largest increase in photo-oxidation current densities for the same sample due to the increased generation of •OH radicals obtained by a more efficient photogenerated charge separation.

TiO2-Powdered Activated Carbon (TiO2/PAC) for Removal and Photocatalytic Properties of 2-Methylisoborneol (2-MIB) in Water

2-methylisoborneol (2-MIB) is a common taste and odor compound caused by off-flavor secondary metabolites, which represents one of the greatest challenges for drinking water utilities worldwide. A TiO2-coated activated carbon (TiO2/PAC) has been synthesized using the sol-gel method. A new TiO2/PAC photocatalyst has been successfully employed in photodegradation of 2-MIB under UV light irradiation. In addition, the combined results of XRD, SEM-EDX, FTIR and UV-Vis suggested that the nano-TiO2 had been successfully loaded on the surface of PAC. Experimental results of 2-MIB removal indicated that the adsorption capacities of PAC for 2-MIB were higher than that of TiO2/PAC. However, in the natural organic matter (NOM) bearing water, the removal efficiency of 2-MIB by TiO2/PAC and PAC were 97.8% and 65.4%, respectively, under UV light irradiation. Moreover, it was shown that the presence of NOMs had a distinct effect on the removal of MIB by TiO2/PAC and PAC. In addition, a simplified equivalent background compound (SEBC) model could not only be used to describe the competitive adsorption of MIB and NOM, but also represent the photocatalytic process. In comparison to other related studies, there are a few novel composite photocatalysts that could efficiently and rapidly remove MIB by the combination of adsorption and photocatalysis.

Surfactant-coupled titanium dioxide coated iron-aluminium mixed metal hydroxide for magnetic solid phase extraction of bisphenols in carbonated beverages

In this work, the magnetic sorbents based on different surfactant-coupled titanium dioxide coated iron-aluminium mixed metal hydroxide were investigated as sorbent for extraction of bisphenol compounds. The structure, morphology, and magnetic property of the synthesized sorbents were investigated. The cetyltrimethylammonium bromide-titanium dioxide coated iron-aluminium mixed metal hydroxide (Fe-Al MMH@TiO2-CTAB) exhibited excellent extraction performance toward bisphenols and was selected as the sorbent for development of magnetic solid phase extraction (MSPE) method. The entire MSPE process was optimized, and the extract was analyzed by high performance liquid chromatography with photodiode array detector. The method provided wide linear calibration ranges for bisphenols between 0.3-6000 μg L-1 with maximum enrichment factors of 280. The limits of detection and limits of quantification were in the ranges of 0.08-0.3 and 0.3-1.0 μg L-1, respectively. The proposed MSPE method was tested for determination of bisphenols in carbonated beverages. The studied carbonated beverages were mostly free of bisphenol contamination; however, BPS, BPA and BPB were detected in samples taken from defective cans. The relative recoveries ranging of 80.2-118.9% were obtained. The as-prepared Fe-Al MMH@TiO2-CTAB sorbent provided high sorption capacities in the range of 2215-2451 mg kg-1 and could be a promising material for bisphenols in beverage samples.