Red mud for the efficient adsorption of U(VI) from aqueous solution: Influence of calcination on performance and mechanism

Insights into enhanced immobilization of uranyl carbonate from seawater by Fe-doped MXene

Extracting uranium from seawater not only reduces radioactive contamination in seawater but also provides a source of uranium energy. However, due to the low concentration of uranium in seawater and the high salinity of seawater, extraction of uranium from seawater is challenging. In this work, we demonstrated a simple strategy to synthesize Fe-doped MXene (Fe@Ti3C2Tx) via a hydrothermal method and applied for uranium enrichment in seawater. The Fe@Ti3C2Tx exhibited excellent adsorption performance in high salinity environments. The removal capacity of Fe@Ti3C2Tx was determined to be 526.6 mg/g for UO2(CO3)22- at 328 K with quick reaction equilibrium (∼ 30 min). Kinetic and thermodynamic analyses of UO2(CO3)22- elimination process on Fe@Ti3C2Tx surface revealed it to be a spontaneous and endothermic single-phase elimination process. FT-IR and XPS analyses further indicated that the removal mechanism of UO2(CO3)22- by Fe@Ti3C2Tx was surface complexation. Our study suggests that Fe@Ti3C2Tx can provide a feasible solution for uranium enrichment in seawater.

Formulation Optimization and Performance Prediction of Red Mud Particle Adsorbents Based on Neural Networks

Red mud (RM), a bauxite residue, contains hazardous radioactive wastes and alkaline material and poses severe surface water and groundwater contamination risks, necessitating recycling. Pretreated RM can be used to make adsorbents for water treatment. However, its performance is affected by many factors, resulting in a nonlinear correlation and coupling relationship. This study aimed to identify the best formula for an RM adsorbent using a mathematical model that examines the relationship between 11 formulation types (e.g., pore-assisting agent, component modifier, and external binder) and 9 properties (e.g., specific surface area, wetting angle, and Zeta potential). This model was built using a back-propagation neural network (BP) based on single-factor experimental data and orthogonal experimental data. The model trained and predicted the established network structure to obtain the optimal adsorbent formula. The RM particle adsorbents had a pH of 10.16, specific surface area (BET) of 48.92 m2·g-1, pore volume of 2.10 cm3·g-1, compressive strength (ST) of 1.12 KPa, and 24 h immersion pulverization rate (ηm) of 3.72%. In the removal of total phosphorus in flotation tailings backwater, it exhibited a good adsorption capacity (Q) and total phosphorous removal rate (η) of 48.63 mg·g-1 and 95.13%, respectively.

Industrial waste-based adsorbents as a new trend for removal of water-borne emerging contaminants

Emerging contaminants in wastewater are one of the growing concerns because of their adverse effects on human health and ecosystems. Adsorption technology offers superior performance due to its cost-effectiveness, stability, recyclability, and reliability in maintaining environmental and health standards for toxic pollutants. Despite extensive research on the use of traditional adsorbents to remove emerging contaminants, their expensiveness, lack of selectivity, and complexity of regeneration remain some of the challenges. Industrial wastes viz. blast furnace slag, red mud, and copper slag can be used to develop efficacious adsorbents for the treatment of emerging contaminants in water. Advantages of the use of such industrial wastes include resource utilization, availability, cost-effectiveness, and waste management. Nevertheless, little is known so far about their application, removal efficacy, adsorption mechanisms, and limitations in the treatment of emerging contaminants. A holistic understanding of the application of such unique industrial waste-derived adsorbents in removing emerging contaminants from water is need of the hour to transform this technology from bench-scale to pilot and large-scale applications. This review investigates different water treatment techniques associated with industrial waste-based adsorbents derived from blast furnace slag, red mud, and copper slag. Besides, this review provides important insights into the growing trends of utilizing such novel types of adsorbents to remove emerging contaminants from water with an emphasis on removal efficacy, controlling measures, adsorption mechanisms, advantages, and limitations. The present timely review brings the current state of knowledge into a single reference which could be a strong platform for future research in understanding the latest advancements, decision making, and financial management related to the treatment of wastewater using industrial waste-based adsorbents.

Application of common industrial solid waste in water treatment: a review

Industrial solid waste has a wide range of impacts, and it is directly or indirectly related to land, atmosphere, water, and other resources. Industrial solid waste has a large amount of production, complex and diverse components and contains a variety of harmful substances. However, as industrial by-products, it also has a lot of available value. Industrial solid waste has been continuously studied in water treatment due to its special composition and porous and loose structure. It is known that there are few reviews of various industrial solid wastes in the field of wastewater treatment, and most of them only discuss single industrial solid waste. This paper aims to sort out the different studies on various solid wastes such as fly ash, red mud, wastewater sludge, blast furnace slag and steel slag in dyeing, heavy metal, and phosphorus-containing wastewater. Based on the modification of industrial solid waste and the preparation of composite materials, adsorbents, coagulants, catalysts, filtration membranes, geological polymers, and other materials with high adsorption properties for pollutants in wastewater were formed; the prospect and development of these materials in the field of wastewater were discussed, which provides some ideas for the mutual balance of environment and society. Meanwhile, some limitations of solid waste applications for wastewater treatment have been put forward, such as a lack of further researches about environment-friendly modification methods, application costs, the heavy metal leaching, and toxicity assessment of industrial solid waste.

Green conversion of waste PET into magnetic Ni0·4Fe2·6O4/(Fe,Ni)@carbon nanostructure for adsorption and separation of dyes from aqueous media

A nanostructured core-shell composite (Ni0·4Fe2·6O4/(Fe,Ni)@carbon, NFC) comprising magnetic nano-cores encapsulated with graphitic shells (≈80 wt%) is prepared by facile and clean mechanochemical-molten salt processing approach using waste PET; providing a specific surface area of 201.9 m2 g-1, well-developed mesopores, and ferromagnetic behavior characterized by the coercivity value of 149 Oe. NFC is utilized as a high-performance adsorbent for the removal of organic dyes from their aqueous solutions. Moreover, the magnetic performance of NFC enables the facile collection of the exhausted adsorbent out of the purified water. Performances of NFC for the removal of crystal violet dye (CV), methyl orange (MO) and rhodamine B (Rh B) from their aqueous solutions are systematically investigated under different environmental conditions including the adsorbent dosage and dye concentration, as well as the solution pH and temperature, where an impressive CV removal capacity of 201.6-243.8 mg g-1 is recorded for a wide pH range of 2-10. Mechanism and kinetics involved in the adsorption process are investigated by studying the adsorption isotherms and thermodynamics. The dye adsorption of the nanocomposite material is confirmed to follow the pseudo-second-order kinetic model combined with the Langmuir isotherm model, exhibiting an excellent spontaneous and exothermic monolayer adsorption capacity of around 153 mg g-1 (for MO) for the fresh adsorbent and around 89 mg g-1 after three adsorption-regeneration cycles.

Efficient separation of uranium(VI) from aqueous solution using magnetic Co/Al layered double oxides coated with carbon dots

Herein, magnetic layered double oxides coated with carbon dots (MLCs) were synthesized through introducing sodium dodecylbenzene sulfonate and FeCl2 into Co/Al LDH for capturing uranium from aqueous solution. When the molar ratio of Co to Al was 4 : 1, the MLC composite possessed the strongest affinity to uranium(VI) in solution with short equilibrium time (<160 min), high adsorption efficiency (94.31%) and large removal capacity (513.85 mg g-1). The adsorption behavior of MLCs for uranium(VI) was well fitted with Langmuir and pseudo-second-order models, suggesting that the monolayer chemical adsorption was the rate-limiting step. Besides, MLC-3 could be reused by using 0.15 mol L-1 ethylene diamine tetraacetic acid as an eluent and the removal percentage still remained at a high level (>83.3%) after 5 adsorption/desorption cycles. Redox reaction, chemical complexation and electrostatic attraction were proved to play significant roles in uranium(VI) separation. Therefore, MLC-3 could be used as a potential adsorbent in uranium(VI)-containing wastewater treatment due to its excellent adsorption performance for uranium(VI).

Graphitic N-doped biochar for superefficient uranium recycling from nuclear wastewater

N-doped biochar (AL-N/BC) prepared by pyrolyzing lignin in various temperatures manifested superefficient performance for uranium (U) recycling from nuclear wastewater. The optimist AL-N/BC-700 showed higher adsorption capacity of 25,000 mg/g and faster kinetics of 4100 g·min^-1·mg^-1 than the most of reported adsorbents, and excellent adsorption-desorption capability (adsorption rate > 90 % and desorption rate > 70 % after 12 cycles). Moreover, the high applicability of AL-N/BC-700 was verified by its superefficient U(VI) adsorption performance in a broad working pH range, various water matrices, and high irradiation stability. Furthermore, the adsorption mechanism discloses the significant role of graphitic N, rather than pyridinic N or pyrrolic N, for U(VI) adsorption. Overall, this work not only presents an applicable approach to alleviate the increasingly serious energy crisis via recycling U(VI) from nuclear wastewater, but also enriches the method of synthesizing N-doped materials for U(VI) adsorption.

Insight into catalytic activation of bisulfite for lomefloxacin degradation by simple composite of calcinated red mud

Antibiotic was detected in many environments, and it had posed a serious threat to human health. The advanced oxidation process has been considered an effective way to treat antibiotics. In this work, using industrial waste red mud (RM) as raw material, a series of modified RM (MRM-T; T donates the calcination temperature) was obtained via a facile calcination method and applied to activate sodium bisulfite (NaHSO₃) for the lomefloxacin (LOM) degradation. Among all MRM-T, MRM-700 exhibited superior catalytic activity, and approximately 89% of LOM (10 mg/L) was degraded at 30 min through the activation of NaHSO₃ ([NaHSO₃] = 0.5 g/L) by MRM-700 ([MRM-700] = 0.9 g/L). Moreover, the kinetic constant of LOM removal in the MRM-700/NaHSO₃ system (0.082 min^-1) was 16.4 times higher than that of the RM-raw/NaHSO₃ system (0.005 min^-1). The as-synthesized product of MRM-700 was characterized by N₂ adsorption-desorption isotherms, X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and Raman spectra. The result indicated that the catalyst possessed excellent pore structure, high specific area, and abundant Fe³⁺ sites, and the lattice of Fe₂O₃ was doped after calcination, both of which were favorable for the activation of NaHSO₃. The quenching experiment proved that •SO₄^- and •OH^- active species were produced in MRM-700/NaHSO₃ system, and •SO₄^- played a dominant role in LOM removal. In addition, the potential LOM degradation pathway was analyzed via UPLC-MS technology and density functional theory (DFT) calculation, and the toxicity of the treated LOM solution was tested by the culture of mung bean sprouts. This study not only provided a feasible strategy for the valuable use of RM to activate NaHSO₃ but also offered a cost-effective catalyst for the efficient removal of pollutants in wastewater.

Application of Mesopore-Activated Red Mud for Phosphorus Adsorption

In this paper, the mesopore-activated red mud (M-ARM) was prepared by treating red mud (RM) with acid under an ultrasonic batch and through heat treatment at 750 C. The surface area and adsorption average pore width of M-ARM were calculated and obtained values of 13.408 m2 g-1 and 25.160 nm, respectively. Therefore, the maximum adsorption capacity of M-ARM for phosphorus was $200.85\pm 1.66\text{mg}{\text{g}}^{-1}$ at 318 K and $\text{pH}=5$ . At a low initial concentration (75 mg L-1), the phosphorus removal capacity by M-ARM material was up to $97.09\pm 0.15\%$ at 313 K. With the temperature scales varying from 298 to 313 K, the values of Gibbs free energy change ( $\Delta G°$ ) were negative and also vary from -37.47 to -36.68. The phosphorus adsorption process in an aqueous solution is spontaneous, and this adsorption process was exothermic with enthalpy change $∆{\text{H}}^{\text{o}}=-14.36$ . From the results of investigations and calculations of thermodynamic values, kinetics, and adsorption capacity of materials, we can confirm that the materials in this study had a low-cost and potential material for applications to treat phosphorus-contaminated water. In addition, the adsorption kinetics of this material for phosphorus were also studied and discussed.

Dissolution behavior of representative elements from red mud (RM) by leaching with titanium white waste acid (TWWA)

Titanium white waste acid (TWWA) was used to dissolve the representative elements from red mud (RM) to achieve the goal of "treating waste with waste." The leaching parameters on the leaching efficiency of Na, Sc, and Al were investigated, in which the analysis of XRD and SEM-EDS on RM and leaching residue was performed. The leaching kinetics of Na, Sc, and Al was studied with unreacted shrinking core model (USCM). The results show that the dealkalization efficiency was close to 100%, and the leaching efficiency of Sc and Al was 82% and 75%, respectively. Cancrinite was dissolved from RM, and then the elements such as Na, Al, and Ca reacted with H₂SO₄ of TWWA. Na existed in the leaching liquor in the form of ions. Ca reacted with sulfuric acid to form anhydrite, which existed in the leaching residue. The particles of RM became smaller and dispersed with each other by acid leaching. The leaching apparent activation energy of Na, Sc, and Al was 4.947 kJ/mol, 6.361 kJ/mol, and 31.666 kJ/mol, respectively. The leaching kinetic equation of Na, Sc, and Al was 1 - (1 - a)^2/3 = 0.084·exp[- 595.05/T]·t by external diffusion, 1 - 2a/3 - (1 - a)^2/3 = 0.021·exp[- 765.16/T]·t by internal diffusion, and ln(1 - a)/3 + (1 - a)^-2/3 - 1 = 67.12·exp[- 3808.8/T]·t by joint action, respectively.

Experimental Investigation on Red Mud from the Bayer Process for Cemented Paste Backfill

Red mud is a by-product of alumina production, and its disposal can have severe environmental consequences. This study experimentally investigates the feasibility of using red mud from the Bayer process for cemented paste backfill (CPB). Different binders and activators were used to improve the mechanical properties, water resistance, and environmental behaviors of red mud-based CPB. In addition, water immersion tests were introduced, for the first time, to evaluate the water resistance of CPB. Furthermore, the environmental behaviors of red mud-based CPB were investigated by conducting leaching experiments. The results showed that the red-mud specimens had an unconfined compressive strength (UCS) of less than 0.2 MPa and disintegrated after being immersed in water. Different binders significantly improved the mechanical properties of red mud-based CPB. In addition, the specimens with different binders showed excellent water resistance, and the softening coefficient of CPB with different binders could exceed 0.7 after being cured for 28 days. The binders exhibited a substantial inhibitory effect on the leaching of hazardous substances in red mud under the solidification and stabilization effects. The leaching concentration of hexavalent chromium, selenium, fluoride, arsenic, lead, and vanadium was reduced by more than 70%. Therefore, this study provides an effective method for the environmental-friendly and large-scale utilization of red mud from the Bayer process.

Effectiveness and mechanism of uranium adsorption on size-graded red mud

As a type of useful solid waste, red mud (RM) should be reused to achieve waste-to-resource strategies. Additionally, the fast development of nuclear industry requires effective and reliable materials for treating uranium (U)-containing wastewater. This study attempted to remove uranyl ions [U(VI)] from mimic radioactive wastewater by various RM particles with different size fractions (e.g., >75, 45-75, 20-45, 10-20, 5-10, and <5-μm). Sorption data confirmed that the RM with a size fraction of <5-μm exhibited the largest adsorption capacity. The U removal behavior was favorably described by the pseudo-second-order model and Langmuir model. The mineral phases in the RM remarkably influenced U(VI) removal. Cancrinite, katoite, grossular, calcite, and calcium aluminum silicate phases made contributions to U(VI) adsorption. In addition, redox precipitation with iron-bearing minerals on RM surface also led to U(VI) adsorption. The findings of this work offer fundamental knowledge on the potential application of RM for clean-up of U(VI) from contaminated sites.

Hexavalent chromium elimination from wastewater by integrated micro-electrolysis composites synthesized from red mud and rice straw via a facile one-pot method

The widely spread chromium (Cr) contamination is rising environmental concerns, while the reutilization of agro-industrial by-products are also urgently demanded due to their potential risks. In this study, we prepared the integrated micro-electrolysis composites (IMC) through a facile one-pot method with red mud and rice straw. The effects of components relatively mass ratios as well as pyrolysis temperature were analyzed. The XRD, XPS, SEM, FTIR, and various techniques proved the IMC was successfully synthesized, which was also used to analyze the reaction mechanisms. In this study, the dosage of IMC, pH, adsorption time, and temperature of adsorption processes were explored, in the adsorption experiment of Cr(VI), dosage of IMC was 2 g/L (pH 6, 25 °C, and 200 rpm) for isothermal, while the concentration and contact time were also varied. According to the batch experiments, IMC exhibited acceptable removal capacity (190.6 mg/g) on Cr(VI) and the efficiency reached 97.74%. The removal mechanisms of adsorbed Cr(VI) were mainly elaborated as chemical reduction, complexation, co-precipitation, and physical adherence. All these results shed light on the facile preparation and agro-industrial by-products recycled as engineering materials for the heavy metals decontamination in wastewater.

Magnetic MXene-NH2 decorated with persimmon tannin for highly efficient elimination of U(VI) and Cr(VI) from aquatic environment

Herein, a magnetic MXenes based composite (Fe₃O₄@Ti₃C₂-NH₂-PT) was constructed by loading Fe₃O₄ nano-particles into the interlamellar spacing of persimmon tannin-functionalized Ti₃C₂-NH₂. The structure, morphology and physicochemical properties of the as-prepared adsorbents were probed by advanced spectroscopy techniques, while the impact of various experimental conditions like pH values, amount of adsorbent and contact time on the removal trend were examined by batch experiments. The elimination results revealed that Fe₃O₄@Ti₃C₂-NH₂-PT could be applied in a wide range of initial concentrations, and exhibited outstanding removal efficiency for U(VI) (104.9 mg/g, pH = 5.0) and Cr(VI) (83.8 mg/g, pH = 2.0). Meanwhile, the adsorption process was described well with the Langmuir isotherm and Pseudo-second-order kinetics models, which indicated that the monolayer chemical adsorption occurred during elimination of the two contaminants. The spectral analysis results manifested that elimination of U(VI) followed an inner-sphere configuration, whereas uptake of Cr(VI) was determined by electrostatic interaction and adsorption-reduction process. This work opened a new opportunity in designing MXenes based adsorbents in the application for environmental remediation.

Clean dealkalization technology from aluminum industry hazardous tailings-red mud by displacement with Mg-based agent

Red mud is a kind of strong alkaline hazardous slag discharged from aluminum metallurgy industry. In this study, the water immersion with high temperature and high pressure was developed for the selective dealkalization from red mud by adding Mg-based additives. The removal efficiency of alkali could reach 92% by using 12% MgCl₂ with 9 mL/g at 250 °C for 60 min. The MgCl₂ was the most effective leaching reagent to promote the decomposion of cancrinite lattice. The new minerals bearing Mg, i.e., chlorite (Mg₅Al₂Si₃O₁₀(OH)₈) and pyrope (Mg₃Al₂Si₃O₁₂) could be formed, which was in favor of transforming the structural alkali into the free alkali by the analysis and validation of XRD and SEM-EDS. The dealkalization process was mainly controlled by chemical reactions according to the analysis of unreacted shrinking core model (USCM) of leaching kinetics. The leaching kinetics equation of 1 - (1 - x)^1/3 = 32.2 × exp[4582.6 / T] × t was built and the apparent activation energy of 38.1 kJ/mol was obtained. This method may provide a new and cleaner way for the efficient dealkalization of red mud and a basis for the utilization of leaching residue as the soil amendment.

Recent advances in waste-derived functional materials for wastewater remediation

Water pollution is a major concern for public health and a sustainable future. It is urgent to purify wastewater with effective methods to ensure a clean water supply. Most wastewater remediation techniques rely heavily on functional materials, and cost-effective materials are thus highly favorable. Of great environmental and economic significance, developing waste-derived materials for wastewater remediation has undergone explosive growth recently. Herein, the applications of waste (e.g., biowastes, electronic wastes, and industrial wastes)-derived materials for wastewater purification are comprehensively reviewed. Sophisticated strategies for turning wastes into functional materials are firstly summarized, including pyrolysis and combustion, hydrothermal synthesis, sol-gel method, co-precipitation, and ball milling. Moreover, critical experimental parameters within different design strategies are discussed. Afterward, recent applications of waste-derived functional materials in adsorption, photocatalytic degradation, electrochemical treatment, and advanced oxidation processes (AOPs) are analyzed. We mainly focus on the development of efficient functional materials via regulating the internal and external characteristics of waste-derived materials, and the material's property-performance correlation is also emphasized. Finally, the key future perspectives in the field of waste-derived materials-driven water remediation are highlighted.

Amidoxime Group-Anchored Single Cobalt Atoms for Anti-Biofouling during Uranium Extraction from Seawater

Marine biofouling is one of the most significant challenges hindering practical uranium extraction from seawater. Single atoms have been widely used in catalytic applications because of their remarkable redox property, implying that the single atom is highly capable of catalyzing the generation of reactive oxygen species (ROS) and acts as an anti-biofouling substance for controlling biofouling. In this study, the Co single atom loaded polyacrylamidoxime (PAO) material, PAO-Co, is fabricated based on the binding ability of the amidoxime group to uranyl and cobalt ions. Nitrogen and oxygen atoms from the amidoxime group stabilize the Co single atom. The fabricated PAO-Co exhibits a broad range of antimicrobial activity against diverse marine microorganisms by producing ROS, with an inhibition rate up to 93.4%. The present study is the first to apply the single atom for controlling biofouling. The adsorbent achieves an ultrahigh uranium adsorption capacity of 9.7 mg g-1 in biofouling-containing natural seawater, which decreased only by 11% compared with that in biofouling-removed natural seawater. These findings indicate that applying single atoms would be a promising strategy for designing biofouling-resistant adsorbents for uranium extraction from seawater.

A novel scheme for the utilization of Cu slag flotation tailings in preparing internal electrolysis materials to degrade printing and dyeing wastewater

About 60 million tons of Fe-rich Cu slag (IRCS) are generated annually worldwide during Cu slag flotation and cause irreversible water and soil pollution. Current research provides an environmentally friendly technology, the preparation of internal electrolysis materials (IEMs) through the carbothermal reduction of IRCS, for the degradation of printing and dyeing wastewater. XRD and SEM-EDS indicated that carbothermal reduction could promote the conversion of fayalite to zero-valent iron (ZVI), and ZVI could effectively form IEM with residual carbon. The degradation capacity of IEM for methylene blue (MB) was remarkably improved compared with raw IRCS after roasting for 60 min at 1100 °C with 35% anthracite dosage. MB degradation efficiency improved by increasing the IEM dosage and reaction temperature and decreasing the MB concentration and solution pH. FTIR, XRD, SEM-EDS, and XPS all detected the formation of Fe oxide or Fe hydroxide. UV-vis and TOC demonstrated that the characteristic groups of MB were destroyed and resulted in the mineralization of MB. MB degradation could be attributed to the Fe²⁺, [H], and ·OH produced by the galvanic reaction induced by IEM. Overall, this study offers theoretical guidance in the treatment of printing and dyeing wastewater and the reuse of IRCS.

Decorating UiO-66-NH2 crystals on recyclable fiber bearing polyamine and amidoxime bifunctional groups via cross-linking method with good stability for highly efficient capture of U(VI) from aqueous solution

Although polyacrylonitrile fiber (PANF) and metal-organic frameworks (MOFs) have been extensively investigated to remove U(VI) from water, their practical applications are seriously hindered by the relatively low stability of PANF in acidic solution and great difficulty of separating MOFs nanoparticles from solution, beside that, little attention is paid to the fabrication of MOFs and PANF composite materials (MPCMs) with excellent adsorption capacity for U(VI). Herein, we report the synthesis of novel MPCMs by decorating different concentrations of UiO-66-NH2 crystals onto polyamine and amidoxime groups functionalized PANF (PA-AO-PANF) through cross-linking method for U(VI) extraction. The characterization results reveal that the combination of PA-AO-PANF and UiO-66-NH2 crystals endows MPCMs with excellent separation ability, large surface area, good stability and plentiful surface functional groups, which contributes to good selectivity and enhanced adsorption performance. Consequently, the obtained UN-PA-AO-PANF-2 shows the maximum uptake capacity of 441.8 mg/g and equilibrium uptake time of 30 min towards U(VI). Besides, the U(VI) uptake ability and structure of UN-PA-AO-PANF-2 are well preserved after ten adsorption-desorption cycles. With these outstanding properties, the adsorbent has great potential for the capture of U(VI) from aqueous solutions. Importantly, this work provides a cost-effective and efficient way to construct extremely stable MPCMs hybrid fibers.

Effect of Carbide Slag on Removal of Na+/K+ from Red Mud Based on Water Leaching

Red mud (RM) is a hazardous solid waste discharged from the alumina production process. The stock of RM is very large, and it has strong alkalinity and certain radioactivity, which makes it have a very serious adverse effect on the environment. Many scholars have carried out extensive experimental investigations on the minimization, hazard-free treatment, and reutilization of RM, and encouraging results have been obtained. However, reutilization of RM has been restricted mainly due to its complex composition and strong alkalinity. In this study, carbide slag, a byproduct of acetylene production, was utilized to remove alkalis (Na⁺ and K⁺) from RM by calcium ion replacement. The effects of the temperature, liquid-to-solid ratio, carbide slag dose, and leaching time on dealkalization of RM by carbide slag were studied. The leaching mechanism of sodium was investigated and analyzed using inductively coupled plasma-atomic emission spectrometry, X-ray diffraction, and scanning electron microscopy with energy-dispersive spectrometry. Under the optimal conditions, the residual Na₂O and K₂O amount in the RM after dealkalization using the carbide slag diminished to less than 0.93 and 0.45 wt %. More than 78.80% of Na₂O and 58.84% of K₂O could be dissolved under the optimal conditions. The cancrinite structure in the initial RM was destroyed, and soluble sodium salts formed in the suspension can be easily replaced by carbide slag reducing Na⁺. The dealkalization process of RM by using carbide slag was controlled by chemical reaction of shrinking core model, where the apparent activation energy was 4.92 kJ/mol.

Stable immobilization of uranium in iron containing environments with microbial consortia enriched via two steps accumulation method

The stable stabilization of uranium (U) in iron (Fe) containing environments is restricted by the reoxidation of UO₂. In the current study, based on air reoxidation tests, we propose a novel two steps accumulation method to enrich microbial consortia from paddy soil. The constructed microbial consortia, denoted as the Fe-U bacteria, can co-precipitate U and Fe to form stable Fe-U solids. Column experiments running for 4 months demonstrated the production of U(IV)-O-Fe(II) precipitates containing maximum of 39.51% uranium in the presence of Fe-U bacteria. The reoxidation experiments revealed the U(IV)-O-Fe(II) precipitates were more stable than UO₂. 16S rDNA high throughput sequencing analysis demonstrated that Acinetobacter and Stenotrophomonas were responsible for Fe and U precipitation, while, Caulobacteraceae and Aminobacter were crucial for the formation of U(VI)-PO₄ chemicals. The proposed two steps accumulation method has an extraordinary application potential in stable immobilization of uranium in iron containing environments.

Heavy metal ions and particulate pollutants can be effectively removed by a gravity-driven ceramic foam filter optimized by carbon nanotube implantation

It is of great significance to develop a new gravity-driven filter to remove water pollutants, but it is still challenging. Here, a novel and simple strategy is demonstrated to manufacture fly ash (FA) ceramic foams showing a three-dimensional interconnected porous structure, with multiwalled carbon nanotubes (MWCNTs) implanted by combining carbamate grafting and polydimethylsiloxane coating. The polydimethylsiloxane formed a physical coating on the carbamate group, generating an effective thermal insulating layer on the outer side of the entire MWCNT. The FA foam, which shows a sufficient adsorption capacity for Pb(II) (51.67 ± 1.17 mg g^-1) and Cd(II) (30.12 ± 0.37 mg g^-1) at pH = 5, T = 25 °C, has a 96.33%, 95.12%, 89.50% removal efficiency for Cd(II), Pb(II), and particulate pollutants, and exhibits excellent recycling performance. This paper provides new opportunities to fabricate gravity-driven filters with low energy consumption for wastewater treatment.

Synthesis of phosphorylated hyper-cross-linked polymers and their efficient uranium adsorption in water

Uranium (U) is hazardous and radioactive, wastewater containing U(VI) should be treated before being discharged. Here, two novel uranium adsorbents, phosphorylated hyper-cross-linked bisphenol A (PHCP-1) and fluorene-9-bisphenol (PHCP-2) were separately synthesized via Friedel-Crafts reaction followed by phosphorylation using phosphorus oxychloride. PHCPs had a BET surface area (up to 564 m²/g) with pore sizes of 2.2-2.8 nm. These adsorbents were used for the first time for uranium adsorption from water and demonstrated outstanding adsorption performance. PHCP-2 had a great uranium adsorption capacity (297.14 mg/g) and a very fast sorption rate (85% removal rate within 5 min). The adsorption data were well fitted with Freundlich isotherm and the pseudo-second-order kinetic model. PHCPs displayed selective adsorption capacity for U(VI) from solution that including a variety of competing metal ions. The reusability was confirmed through three regeneration cycles. Based on a series of spectroscopic analyses, the mechanism of action between PHCPs and U(VI) is primarily derived from the complex between phosphate functional groups and U (VI). The sorption performance of PHCPs is attributed to their huge specific surface area and the strong complex between phosphate groups and U(VI). These findings suggest that PHCPs could be useful in the effective adsorption of uranium from water.

Uranium uptake from wastewater by the novel MnxTi1-xOy composite materials: Performance and mechanism

The novel Mn_xTi_1-xO_y composite materials with different mole ratios (Mn to Ti = 3:7, 5:5 and 7:3) were prepared to remove uranium species from wastewater. These composite materials were characterized by various techniques, such as thermogravimetric analysis (TG), X-ray diffraction (XRD), Fourier transformed infrared (FT-IR) and scanning electron microscopy (SEM). It was found that the chitosan in Mn_xTi_1-x-Chi were completely removed after calcination at 650 °C and Mn_xTi_1-xO_y composites possessed uniform distribution of the porous structure as well as plentiful hydroxyl-containing groups. Moreover, the as-prepared Mn_xTi_1-xO_y composite materials were applied to remove uranium from solution to evaluate the adsorption performance. It was found that the Mn_0.5Ti_0.5O_y possessed relatively excellent uptake performance for uranium comparing with the Mn_0.3Ti_0.7O_y and Mn_0.7Ti_0.3O_y and its maximum uptake capacity and efficiency reach 695.2 mg/g and 98.6% (pH = 4, m/V = 0.1 g/L, T = 298 K), respectively, which were much superior than most of reported materials based on titanium oxide or manganese oxide. Besides, the uranium uptake on Mn_0.5Ti_0.5O_y was independent on ionic strength and it had considerable reusability, which might be the necessary condition for Mn_0.5Ti_0.5O_y to be applied in uranium uptake from uranium-containing wastewater. As a candidate adsorbent, Mn_0.5Ti_0.5O_y possessed a high potentiality to remove uranium from wastewater.