"Oxynitride trap" over N/S co-doped graphene-supported catalysts promoting low temperature NH3-SCR performance: Insight into the structure and mechanisms

Self-protected Chlorella@Mn catalyst with excellent resistance to alkali/alkaline earth metal for NOx reduction by NH3

In the selective catalytic reduction of NOx by NH3 (NH3-SCR), conventional Mn-based denitration catalysts often suffered from susceptibility to poisoning by alkali and alkaline earth metals, this paper presented an innovative self-protected Chlorella@Mn denitration catalyst. Remarkably, in the presence of high concentrations (2 wt%) of alkali and alkaline earth metal oxides, the Chlorella@Mn catalyst sustained a NOx conversion exceeding 96 % at 175 °C. At an even higher concentration (4 wt%), NOx conversion above 90 % at 175 °C, surface analysis revealed that POMn sites acted as sacrificial sites, binding to the alkali and alkaline earth metals, the Chlorella@Mn catalyst surface naturally carried a spectrum of acidic species (such as SO42-, PO3-, SiO32-), proficient in capturing alkali/alkaline earth metal effectively, elements such as S, P, and Si formed bonds with K, Na, Ca, and Mg. The synergistic protection of the active sites and the surface elements avoided the deactivation of the catalyst. The detrimental effects of high concentrations of alkali and alkaline earth metals were primarily due to promoting an excessively high valence state of Mn on the catalyst surface and the reduction or loss of NH3 adsorption and activation at Brønsted acid sites. This research provided valuable insights for advancing the development of low-temperature denitration catalysts with improved resistance to alkali and alkaline earth metal poisoning.

Optimization of Injection Source Settings for SNCR Numerical Simulation of Low-Water Content Biomass Boilers with Blending

In order to control NOx emissions and meet China's ultralow emission standards, a numerical simulation based on the computational fluid dynamics (CFD) approach is performed for the optimization of the reductant injection volume, number of injection sources, distribution, and injection direction for the flue gas denitrification process of a circulating fluidized bed boiler (CFB) blended with low-water content biomass in a 168 MW unit of a thermal power plant. Using the target power plant boiler entity as a template, a simplified geometric model is established, 1:1, and the mass fractions of each flue gas component set by the inlet boundary conditions are O22, H2O11.6, CO216.2%, and NO0.05%(about 134 ppm), and the reduction reactions under different optimized conditions are numerically simulated using the SNCR model in ANSYS Fluent 2021 R1. The simulation results under each condition were analyzed. The results show that the optimal ammonia-to-nitrogen ratio should be taken as NSR = 1.25, the denitrification efficiencies of 81.00, 81.63, and 82.74% at the three outlets are high, and the ammonia escapes of 1.76, 2.08, and 9.42 mg/s are within a reasonable range; increasing the number of injection sources can significantly reduce the disturbance of the flue gas flow field by reductant injection; the direction of injection is parallel to the direction of the flue gas flow, and the line of the injection source is orthogonal to the direction of the flue gas flow, which is conducive to the mixing of the reductant and flue gas; the optimized boiler denitrification efficiency reaches 74.2%, meeting the ultralow emission requirements of nitrogen oxides and ammonia escape.

Promotion of SO2 resistance of Ce-La/TiO2 denitrification catalysts by V doping

Conventional cerium-based denitrification catalysts show good catalytic activity at moderate and high temperatures, but their denitrification performance may be decreased due to poisoning by SO2 in the flue gas. In this paper, V was introduced into Ce-La/TiO2 catalysts by a ball-milling method, and the effects of the V content on catalyst denitrification performance and SO2 resistance were investigated. Fourier-transform diffuse reflectance in situ infrared spectroscopy was used to examine the denitrification mechanism and evaluate the catalysts for surface acidity, redox characteristics, and SO2 adsorption. After introducing V, Brønsted acids played the dominant role in the catalytic reaction by increasing the number of acidic sites on the catalyst surface, adsorbing NH3 to participate in the reaction, and improving the sulfur resistance by inhibiting SO2 poisoning. The Ce3+ and O ratio on the catalyst surface were also enhanced by V doping, which reduced interactions between SO2 and the primary metal oxide active ingredients. The modified catalyst inhibited the formation of sulfate species on the catalyst surface and prevented the generation of additional nitrate species on the surface, which protected the main active sites. After V doping, the NH3-SCR reaction on the catalyst surface followed the Langmuir-Hinshelwood mechanism.

Uncovering the centrality of mono-dentate SO32-/SO42- modifiers grafted on a metal vanadate in accelerating wet NOX reduction and poison pyrolysis

NOX rarely binds with labile oxygens of catalytic solids, whose Lewis acidic (LA) species possess higher binding strengths with NH3 (ENH3) and H2O than Brönsted acidic counterparts (BA--H+; -OH), oftentimes leading to elevate energy barrier (EBARRIER) and weaken H2O tolerance, respectively. These limit NH3-assisted wet NOX reduction via Langmuir-Hinshelwood-type or Eley-Rideal (ER)-type model on LA species, while leaving ER-type analogue on BA--H+ species proper to reduce wet NOX. Given hard-to-regulate strength/amount of -OH species and occasional association between ENH3 and EBARRIER, Ni1V2O6 (Ni1) was rationally chosen as a platform to isolate mono-dentate SO32-/SO42- species for use as BA--H+ bonds via protonation to increase collision frequency (k'APP,0) alongside with disclosure of advantages of SO32-/SO42--functionalized Ni1V2O6 (Ni1-S) over Ni1 in reducing wet NOX. Ni1-S outperformed Ni1 in achieving a larger BA--H+ quantity (k'APP,0↑), increasing H2O tolerance, and elevating oxygen mobility, thus promoting NOX reduction activity/consequences under SO2-excluding gases. V2O5-WO3 composite simulating a commercial catalyst could isolate mono-dentate SO32-/SO42- species and served as a control (V2O5-WO3-S) for comparison. Ni1-S was superior to V2O5-WO3-S in evading ammonium (bi-)sulfate (AS/ABS) poison accumulation and expediting AS/ABS pyrolysis efficiency, thereby improving AS/ABS resistance under SO2-including gases, while enhancing resistance against hydro-thermal aging.

Unveiling alkali metal poisoning of CrMn catalyst for selective catalytic reduction of NOx with NH3: An experimental and theoretical study

Alkali metal poisoning has been an intricate and unsolved issue confining the catalytic activity of NH₃-SCR catalysts up to now. Herein, the effect of NaCl and KCl on catalytic activity of CrMn catalyst for NH₃-SCR of NO_x was systematically investigated to clarify the alkali metal poisoning by combined experiments and theoretical calculations. It unveiled that NaCl/KCl could deactivate CrMn catalyst due to the decrease in specific surface area, electron transfer (Cr⁵⁺+Mn³⁺↔Cr³⁺+Mn⁴⁺), redox ability and oxygen vacancy and NH₃/NO adsorption. In addition, NaCl cut off E-R mechanism reactions by inactivating surface Brønsted/Lewis acid sites. DFT calculations revealed that (1) Na and K could weaken MnO bond, (2) competitive adsorption between Cl and NH₃ was a main reason weakening Lewis acid, (3) Cl adsorption was also a major cause diminishing Brønsted acid and oxygen vacancy, (4) Both Na and K seriously impeded NO adsorption/activation, (5) NaCl/KCl increased the reaction heat of H₂O desorption (rate-determining step) in E-R mechanism reactions and KCl elevated its energy barrier in L-H mechanism reactions. Thus, this study provides the deep understanding of alkali metal poisoning and a well strategy to synthesize NH₃-SCR catalysts with outstanding alkali metal resistance.

Appropriate oxygen vacancies and Mo-N bond synergistically modulate charge transfer dynamics of MoO3-x/S-CN for superior photocatalytic disinfection: Unveiling synergistic effects and disinfection mechanism

Highly efficient charge transfer is a critical factor to modulate the photocatalytic activity. However, the conscious modulation of charge transfer efficiency is still a great challenge. Herein, a novel interfacial Mo-N bond and appropriate oxygen vacancies (OVs) modulated S-scheme MoO_3-x/S-CN heterojunction was rationally fabricated for efficient photocatalytic disinfection. The results of characterizations and density functional theory (DFT) calculations suggested that the enhanced charge transfer dynamics is ascribed to the optimizing oxygen vacancies density and forming interfacial Mo-N bond. It can improve charge transfer efficiency from 36.4% (MoO_3-x) to 52.5% (MoO_3-x/S-CN) and produce more reactive oxygen species (ROS), achieving entirely inactivate of 7.60-log E. coli and S. aureus within 50 min and 75 min. Besides, MoO_3-x/S-CN can well resist the disturbance from the coexisting substances, and can be applied in a wide pH range, and even authentic water bodies. Monitoring of bacterial antioxidant systems and membrane integrity revealed that bacterial inactivation begins with the oxidation of cell membrane and dies from leakage of intracellular substances and destruction of cell structure. This work provides an inspiration on consciously modulating S-scheme charge transfer efficiency by optimizing oxygen vacancies density and atomic-level interface control for promoting the photocatalytic antibacterial activity.

Organic–Inorganic Double-Gel System Thermally Insulating and Hydrophobic Polyimide Aerogel

Aerogel materials are used in various fields, but there is a shortage of aerogel materials with an excellent combination of mechanical properties, thermal stability, and easy preparation. In this study, polyimide aerogel materials with superior mechanical properties, thermal stability, and low thermal conductivity were prepared by forming a double-gel system in the liquid phase. The amino-modified gel, prepared by coating SiO₂ nano-microspheres with GO through a modified sol-gel method (SiO₂@GO-NH₂), was subsequently homogeneously dispersed with PAA wet gel in water to form a double-gel system. The construction of a double-gel system enabled the PI aerogel to shape a unique honeycomb porous structure and a multi-layered interface of PI/SiO₂/GO. The final obtained PI aerogel possessed effective thermal conductivity (0.0309 W/m·K) and a high specific modulus (46.19 m²/s²). In addition, the high thermal stability (543.80 °C in Ar atmosphere) and the ability to retain properties under heat treatment proved its durability in high thermal environments. The hydrophobicity (131.55°) proves its resistance to water from the environment. The excellent performance of this PI aerogel and its durability in thermal working environments make it possible to be applied in varied industrial and research fields, such as construction and energy, where heat and thermal insulation are required.