Enhanced electro-oxidation performance of FeCoLDH to organic pollutants using hydrophilic structure

Efficient Charge Separation in Ag/PCN/UPDI Ternary Heterojunction for Optimized Photothermal-Photocatalytic Performance via Tandem Electric Fields

Charge separation driven by the internal electric field is a research hotspot in photocatalysis. However, it remains challenging to accurately control the electric field to continuously accelerate the charge transfer. Herein, a strategy of constructing a tandem electric field to continuously accelerate charge transfer in photocatalysts is proposed. The plasma electric field, interface electric field, and intramolecular electric field are integrated into the Ag/g-C3N4/urea perylene imide (Ag/PCN/UPDI) ternary heterojunction to achieve faster charge separation and longer carrier lifetime. The triple electric fields function as three accelerators on the charge transport path, promoting the separation of electron-hole pairs, accelerating charge transfer, enhancing light absorption, and increasing the concentration of energetic electrons on the catalyst. The H2 evolution rate of Ag/PCN/UPDI is 16.8 times higher than that of pristine PDI, while the degradation rate of oxytetracycline is increased by 4.5 times. This new strategy will provide a groundbreaking idea for the development of high-efficiency photocatalysts.

Doping and defects in carbon nitride cause efficient in situ H2O2 synthesis to allow efficient photocatalytic sterilization

In situ photocatalytic synthesis of H2O2 for disinfection has attracted widespread attention because it is a clean and environmentally friendly sterilization method. Graphitic carbon nitride has been used as a very selective photocatalyst for H2O2 generation but has some limitations (e.g., insufficient light absorption, rapid electron-hole recombination, and slow direct two-electron reduction processes) that prevent efficient H2O2 production. In this study, potassium-doped graphite carbon nitride with nitrogen vacancies (NDKCN) was prepared using a simple method involving a thermal fusion salt and N2 calcination, which possessed an ultrathin nanosheet structure (1.265 nm) providing abundant active sites. Synergistic effects caused by nitrogen vacancies and K+ and I- doping in the NDKCN photocatalyst gave the NDKCN a good ability to absorb light, undergo fast charge transfer, and give a high photoelectric current response. The optimized photocatalytic H2O2 yield of the NDKCN was 780.1 μM·g-1·min-1, which was 10 times the yield of the pristine g-C3N4. Tests involving quenching reactive species, electron spin resonance, and rotating disk electrodes indicated that one-step two-electron direct reduction on the NDKCN caused excellent H2O2 generation performance. The ability to efficiently generate H2O2 in situ gave NDKCN an excellent bactericidal performance, and 7.3 log10 (colony-forming units·mL-1) of Escherichia coli were completely eliminated within 80 min. Scanning electron microscopy images before and after sterilization indicated the changes in bacteria caused by the catalytic activity. The new g-C3N4-based photocatalyst and similar rationally designed photocatalysts with doping and defects offer efficient and simple in situ H2O2 sterilization.

The synergistic effect of periodate/ferrate (VI) system on disinfection of antibiotic resistant bacteria and removal of antibiotic resistant genes: The dominance of Fe (IV)/Fe (V)

The proliferation of antibiotic resistant genes (ARGs) and antibiotic resistant bacteria (ARB) caused by antibiotic abuse has raised concerns about the global infectious-disease crisis. This study employed periodate (PI)/ferrate (VI) (Fe (VI)) system to disinfect Gram-negative ARB (Escherichia coli DH5α) and Gram-positive bacteria (Bacillus subtilis ATCC6633). The PI/Fe (VI) system could inactivate 1 × 108 CFU/mL of Gram-negative ARB and Gram-positive bacteria by 4.0 and 2.8 log in 30 min. Neutral and acidic pH, increase of PI dosage and Fe (VI) dosage had positive impacts on the inactivation efficiency of ARB, while alkaline solution and the coexistence of 10 mM Cl-, NO3-, SO42- and 20 mg/L humic acid had slightly negative impacts. The reactive species generated by PI/Fe (VI) system could disrupt the integrity of cell membrane and wall, leading to oxidative stress and lipid peroxidation. Intracellular hereditary substance, including DNA and ARGs (tetA), would leak into the external environment through damaged cells and be degraded. The electron spin resonance analysis and quenching experiments indicated that Fe (IV)/Fe (V) played a leading role in disinfection. Meanwhile, PI/Fe (VI) system also had an efficient removal effect on sulfadiazine, which was expected to inhibit the ARGs transmission from the source.

Oxygen vacancies synergistic cobalt phosphide electron bridge modulated bismuth oxychloride/carbon nitride Z-scheme junction for efficient carbon dioxide reduction coupled with tetracycline oxidation

Although great progress has been made with respect to electron bridges, the electron mobility of the state-of-the-art electron bridges is far from satisfactory because of weak electrical conductivity. To overcome the above issue, cobalt phosphide (CoP), as a model electron bridge, was modified by superficial oxygen vacancies (OVs) and embedded into a defective bismuth oxychloride/carbon nitride (BiO1-xCl/g-C3N4) Z-scheme heterojunction to obtain atomic-level insights into the effect of surface OVs on CoP electron bridges. Compared to BiO1-xCl/g-C3N4 and bismuth oxychloride/cobalt phosphide/carbon nitride (BiOCl/CoP/g-C3N4) composites, the defective bismuth oxychloride/cobalt phosphide/carbon nitride (BiO1-xCl/CoP/g-C3N4) heterojunction exhibited remarkable photocatalytic redox performance, indicating that the surface OVs-assisted CoP electron bridge effectively boosted electrical conductivity and yielded ultrafast electron transfer rates. The theoretical and experimental results demonstrate that the surface OVs play a critical role in improving the electrical conductivity of the CoP electron bridge, thereby accelerating electron mobility. This research provides insights into interfacial OVs-modified transition metal phosphide (TMP) electron bridges and their potential application in heterojunctions for energy crisis mitigation and environmental remediation.

Insights into the Mechanism of Selective Removal of Heavy Metal Ions by the Pulsed/Direct Current Electrochemical Method

Heavy metal pollution treatment in industrial wastewater is crucial for protecting biological and environmental safety. However, the highly efficient and selective removal of heavy metal ions from multiple cations in wastewater is a significant challenge. This work proposed a pulse electrochemical method with a low-/high-voltage periodic appearance to selectively recover heavy metal ions from complex wastewater. It exhibited a higher recovery efficiency for heavy metal ions (100% for Pb2+ and Cd2+, >98% for Mn2+) than other alkali and alkaline earth metal ions (Na+, Ca2+, and Mg2+ were kept below 3.6, 1.3, and 2.6%, respectively) in the multicomponent solution. The energy consumption was only 34-77% of that of the direct current electrodeposition method. The results of characterization and experiment unveil the mechanism that the low-/high-voltage periodic appearance can significantly suppress the water-splitting reaction and break the mass-transfer limitation between heavy metal ions and electrodes. In addition, the plant study demonstrates the feasibility of treated wastewater for agricultural use, further proving the high sustainability of the method. Therefore, it provides new insights into the selective recovery of heavy metals from industrial wastewater.

Progress in layered double hydroxides (LDHs): Synthesis and application in adsorption, catalysis and photoreduction

Layered double hydroxides (LDHs), also known as anionic clays, have attracted significant attention in energy and environmental applications due to their exceptional physicochemical properties. These materials possess a unique structure with surface hydroxyl groups, tunable properties, and high stability, making them highly desirable. In this review, the synthesis and functionalization of LDHs have been explored including co-precipitation and hydrothermal methods. Furthermore, extensive research on LDH application in toxic pollutant removal has shown that modifying or functionalizing LDHs using materials such as activated carbon, polymers, and inorganics is crucial for achieving efficient pollutant adsorption, improved cyclic performance, as well as effective catalytic oxidation of organics and photoreduction. This study offers a comprehensive overview of the progress made in the field of LDHs and LDH-based composites for water and wastewater treatment. It critically discusses and explains both direct and indirect synthesis and modification techniques, highlighting their advantages and disadvantages. Additionally, this review critically discusses and explains the potential of LDH-based composites as absorbents. Importantly, it focuses on the capability of LDH and LDH-based composites in heterogeneous catalysis, including the Fenton reaction, Fenton-like reactions, photocatalysis, and photoreduction, for the removal of organic dyes, organic micropollutants, and heavy metals. The mechanisms involved in pollutant removal, such as adsorption, electrostatic interaction, complexation, and degradation, are thoroughly explained. Finally, this study outlines future research directions in the field.

Photothermal Synergistic Catalysis over Defective Zn3In2S6 for CO2 Fixation

Carbon dioxide (CO2) cycloaddition not only produces highly valued cyclic carbonate but also utilizes CO2 as C1 resources with 100% atomic efficiency. However, traditional catalytic routes still suffer from inferior catalytic efficiency and harsh reaction conditions. Developing multienergy-field catalytic technology with expected efficiency offers great opportunity for satisfied yield under mild conditions. Herein, Zn3In2S6 with sulfur vacancies (Sv) was fabricated with the assistance of cetyltrimethylammonium bromide (CTAB), which is further employed for photothermally driven CO2 cycloaddition first. Photoluminescence spectroscopy and photoelectrochemical characterization demonstrated its superior separation kinetics of photoinduced carriers induced by defect engineering. The temperature-programmed desorption (TPD) technique indicated its excellent Lewis acidity-basicity characters. Due to the combination of above merits from photocatalysis and thermal catalysis, defective Zn3In2S6-Sv achieved a yield as high as 73.2% for cyclic carbonate at 80 °C under blue LED illumination within 2 h (apparent quantum yield of 0.468% under illumination of 380 nm monochromatic light at 36 mW·cm-2), which is 2.9, 2.0, and 6.9 times higher than that in dark conditions and those of pristine Zn3In2S6 and industrial representative tetrabutylammonium bromide (TBAB) thermal-catalysis process under the same conditions, respectively. The synergistic reaction path of photocatalysis and thermal catalysis was discriminated by theoretical calculation. This work provides new insights into the photothermal synergistic catalysis CO2 cycloaddition with defective ternary metal sulfides.

A novel multifunctional magnetically recyclable BiOBr/ZnFe2O4-GO S-scheme ternary heterojunction: Photothermal synergistic catalysis under Vis/NIR light and NIR-driven photothermal detection of tetracycline

The threat of tetracycline (TC) to human health has become a significant issue that cannot be disregarded. Herein, in order to achieve effective degradation and high-sensitivity detection of TC, BiOBr/ZnFe2O4-GO (BOB/ZFO-GO) S-scheme heterojunction nanocomposites (NCs) have been prepared using hydrothermal method. GO with high light absorption capacity accelerated the electron transfer between BiOBr and ZnFe2O4 nanocrystals and extended the light absorption region of BOB/ZFO NCs. The optimal GO addition of BOB/ZFO-GO NCs could degrade TC solution of 10 mg/L in 80 min and have a high reaction rate constant (k) of 0.072 min-1 under visible/NIR light. According to calculations, the non-metal photocatalyst (BOB/ZFO-GO(2)) with the best degradation performance had a photothermal conversion efficiency of up to 23%. Meanwhile, BOB/ZFO-GO NCs could be recycled by magnetic field. The excellent photocatalytic and photothermal performance could be maintained even after several cycles. In addition, a photothermal detection sensor based on a photothermal material/specific recognition element/tetracycline sandwich-type structure was constructed for the trace detection of TC concentration with a detection limit as low as 10-4 ng/mL. This research provides a unique idea for the multi-functionalization of photocatalysts and has a wide range of potential applications for the identification and treatment of organic wastewater.

Interfacial Micro-Environment of Electrocatalysis and Its Applications for Organic Electro-Oxidation Reaction

Conventional designing principal of electrocatalyst is focused on the electronic structure tuning, on which effectively promotes the electrocatalysis. However, as a typical kind of electrode-electrolyte interface reaction, the electrocatalysis performance is also closely dependent on the electrocatalyst interfacial micro-environment (IME), including pH, reactant concentration, electric field, surface geometry structure, hydrophilicity/hydrophobicity, etc. Recently, organic electro-oxidation reaction (OEOR), which simultaneously reduces the anodic polarization potential and produces value-added chemicals, has emerged as a competitive alternative to oxygen evolution reaction, and the role IME played in OEOR is receiving great interest. Thus, this article provides a timely review on IME and its applications toward OEOR. In this review, the IME for conventional gas-involving reactions, as a contrast, is first presented, and then the recent progresses of IME toward diverse typical OEOR are summarized; especially, some representative works are thoroughly discussed. Additionally, cutting-edge analytical methods and characterization techniques are introduced to comprehensively understand the role IME played in OEOR. In the last section, perspectives and challenges of IME regulation for OEOR are shared.

Waste biomass-derived N, P co-doping carbon aerogel-coated CoxFe1-xP with modulated electron density for efficient electrooxidation of contaminants

Developing low-cost, green, high-performing electrode materials to address environmental pollutants and the energy crisis is significant but challenging. Herein, the bimetallic iron cobalt phosphide coated in waste biomass-derived N, P co-doping carbon (CoxFe1-xP@NPC) is constructed. Furthermore, the active site density and the water decomposition energy barrier of surface-coated NPC are modulated by optimizing the electronic structure of CoxFe1-xP via doping engineering. The Fe-modulated CoxFe1-xP@NPC exhibits a hierarchical porous self-supporting structure and excellent physical & chemical properties with excellent electrooxidation performance, achieving over 95% removal of TCH within 60 min. The density functional theory (DFT) calculations further confirms that N carries more positive charge and P carries more negative charge in the NPC of CoxFe1-xP@NPC with Fe modulation, which can promote the adsorption and dissociation of water molecules. Of note, Co0.75Fe025P@NPC displays a low water dissociation energy barrier to produce ·OH and a high energy barrier to produce O2 than its counterparts. This study offers new insight into controllable modulation of biomass carbon-based composite electrode catalytic activity for high-efficiency degradation of contaminants.

Immobilization of zinc and cadmium by biochar-based sulfidated nanoscale zero-valent iron in a co-contaminated soil: Performance, mechanism, and microbial response

Mining and smelting of mineral resources causes excessive accumulation of potentially toxic metals (PTMs) in surrounding soils. Here, biochar-based sulfidated nanoscale zero-valent iron (SNZVI/BC) was designed via a one-step liquid phase reduction method to immobilize cadmium (Cd) and zinc (Zn) in a copolluted arable soil. A 60 d soil incubation experiment revealed that Cd and Zn immobilization efficiency by 6 % SNZVI/BC (25.2-26.2 %) was higher than those by individual SNZVI (13.9-18.0 %) or biochar (14.0-19.3 %) based on the changes in diethylene triamine pentaacetic acid (DTPA)-extractable PTM concentrations in soils, exhibiting a synergistic effect. Cd2+ or Zn2+ replaced isomorphously Fe2+ in amorphous ferrous sulfide, as revealed by XRD, XPS, and high-resolution TEM-EDS, forming metal sulfide precipitates and thus immobilizing PTMs. PTM immobilization was further enhanced by adsorption by biochar and oxidation products (Fe2O3 and Fe3O4) of SNZVI via precipitation and surface complexation. SNZVI/BC also increased the concentration of dissolved organic carbon and soil pH, thus stimulating the abundances of beneficial bacteria, i.e., Bacilli, Clostridia, and Desulfuromonadia. These functional bacteria further facilitated microbial Fe(III) reduction, production of ammonium and available potassium, and immobilization of PTMs in soils. The predicted function of the soil microbial community was improved after supplementation with SNZVI/BC. Overall, SNZVI/BC could be a promising functional material that not only immobilized PTMs but also enhanced available nutrients in cocontaminated soils.

Surface Modification of ZnO with Sn(IV)-Porphyrin for Enhanced Visible Light Photocatalytic Degradation of Amaranth Dye

Two hybrid composite photocatalysts, denoted as SnP/AA@ZnO and SnP@ZnO, were fabricated by a reaction of trans-dihydroxo[5,10,15,20-tetrakis(4-pyridyl)porphyrinato]tin(IV) (SnP) and ZnO with and without pretreatment of adipic acid (AA), respectively. In SnP@ZnO, SnP and ZnO are likely held together by a coordinative interaction between the pyridyl N atoms of SnP and the Zn atoms on the surface of ZnO. In the case of SnP/AA@ZnO, the SnP centers were robustly coupled with ZnO nanoparticles through the AA anchors. SnP/AA@ZnO exhibited largely enhanced photocatalytic activities for the degradation of anionic amaranth (AM) dye under a visible light irradiation, compared to SnP, ZnO, and SnP@ZnO. The degradation efficiency of AM by SnP/AA@ZnO was 95% within 60 min at a rate constant of 0.048 min-1. The remarkable photocatalytic oxidation performance of SnP/AA@ZnO was mainly attributed to the synergistic effect between SnP and ZnO. This study is valuable for the development of highly effective composite photocatalytic systems in advanced oxidation processes and is of importance for the treatment of wastewater containing dyes.

Recent Advances in Thallium Removal from Water Environment by Metal Oxide Material

Thallium is widely used in industrial and agricultural development. However, there is still a lack of systematic understanding of its environmental hazards and related treatment methods or technologies. Here, we critically assess the environmental behavior of thallium in aqueous systems. In addition, we first discuss the benefits and limitations of the synthetic methods of metal oxide materials that may affect the practicality and scalability of TI removal from water. We then assess the feasibility of different metal oxide materials for TI removal from water by estimating the material properties and contaminant removal mechanisms of four metal oxides (Mn, Fe, Al, and Ti). Next, we discuss the environmental factors that may inhibit the practicality and scalability of Tl removal from water. We conclude by highlighting the materials and processes that could serve as more sustainable alternatives to TI removal with further research and development.

Synthesis of honeycomb lignin-based biochar and its high-efficiency adsorption of norfloxacin

In this study, honeycomb lignin-based biochar (HLB) was prepared by hydrothermal activation using industrial lignin as raw material to remove norfloxacin from water. Batch adsorption test results showed that HLB has a strong ability to remove norfloxacin at a wide pH. The maximum adsorption capacity was 529.85 mg/g at 298 K, which is 1.52-fold to 201.46-fold higher than that of other reported materials. HLB showed good selectivity and recycling ability for the adsorption of norfloxacin, the removal rate of NOR reached 99.5% in the presence of competitive ions and maintained at least 98% removal rate after 12 adsorption cycles. The removal rate of norfloxacin in different water reached more than 99% within 8 mins. Pore filling, electrostatic interaction, π-π interaction, and hydrogen bond contributed significantly to the removal of norfloxacin. Among them, the highly aromatized structure of HLB and the abundant oxygen-containing functional groups (OH, CO, etc.) promoted π-π interaction.

Electrochemical degradation of tetracycline hydrochloride in sulfate solutions on boron-doped diamond electrode: The accumulation and transformation of persulfate

In this study, a novel electrifying mode (divided power-on and power-off stage) was applied in the system of BDD activate sulfate to degrade tetracycline hydrochloride (TCH). The BDD electrode could activate sulfate and H₂O to generate sulfate radicals (SO₄^•-) and hydroxyl radicals (^•OH) to remove TCH, and SO₄^•- could dimerize to form S₂O₈^2-. Then, the S₂O₈^2- was activated by heat and quinones to generate SO₄^•- for the continuous degradation of TCH during the power-off stage. In addition, the intermittent time has a significant effect on the degradation of TCH. Factors, affecting the accumulation of S₂O₈^2-, were analyzed using a full factorial design, and the accumulation of S₂O₈^2- could reach 16.2 mM in 120 min. The results of electron spin resonance and radical quenching test showed that SO₄^•-, ^•OH, direct electron transfer (DET), and non-radical in the system could effectively degrade TCH, and SO₄^•- was dominated. The intermediate products of TCH were analyzed by HPLC-QTOF-MS/MS, and the TCH mainly underwent hydroxylation, demethylation and ring opening reactions to form small molecules, and finally mineralized. The results of the feasibility analysis revealed that some intermediates have high toxicity, but the system could improve the toxicity. The results of energy consumption indicated that the intermittent electrifying mode could make full use of the persulfate generated during the power-on stage and reduce about 30% energy consumption. In conclusion, this work demonstrated that it was economically feasible to degrade TCH in wastewater by activating sulfate with BDD electrodes with an intermittent electrifying mode.

The effects of biochar on antibiotic resistance genes (ARGs) removal during different environmental governance processes: A review

Antibiotic resistance genes (ARGs) pollution has been considered as one of the most significant emerging environmental and health challenges in the 21st century, many efforts have been paid to control the proliferation and dissemination of ARGs in the environment. Among them, the biochar performs a positive effect in reducing the abundance of ARGs during different environmental governance processes and has shown great application prospects in controlling the ARGs. Although there are increasing studies on employing biochar to control ARGs, there is still a lack of review paper on this hotspot. In this review, firstly, the applications of biochar to control ARGs in different environmental governance processes were summarized. Secondly, the processes and mechanisms of ARGs removal promoted by biochar were proposed and discussed. Then, the effects of biochar properties on ARGs removal were highlighted. Finally, the future prospects and challenges of using biochar to control ARGs were proposed. It is hoped that this review could provide some new guidance for the further research of this field.