Online TG-FTIR-MS analysis of the catalytic pyrolysis of polyethylene and polyvinyl chloride microplastics

Upcycling of PVC waste to high-value sorbent with KOH-activation for efficient removal of organic dyes

Polyvinyl chloride (PVC), known for its chemical stability and flame-retardant qualities, has many uses in various fields, such as pipes, electric wires, and cable insulation. Research has established its potential recovery as a fluidic fuel through pyrolysis, but the use of PVC pyrolysis oil, which is tainted by chlorine, is constrained by its low heat value and harmful environmental effects. This study engineered a layered double hydroxide (LDH) to tackle these challenges. The LDH facilitated dechlorination during PVC pyrolysis and bolstered thermal stability via cross-linking. During pyrolysis with LDH, PVC was transformed into carbon-rich precursors to sorbents. Chemical activation of these residues using KOH created sorbents with a specific surface area of 1495.4 m2 g⁻1, rendering them hydrophilic. These resulting sorbents displayed impressive adsorption capabilities, removing up to 486.79 mg g⁻1 of methylene blue and exhibiting the simultaneous removal of cations and anions.

Microplastics in water: Occurrence, fate and removal

A global study on tap water samples has found that up to 83% of these contained microplastic fibres. These findings raise concerns about their potential health risks. Ingested microplastic particles have already been associated with harmful effects in animals, which raise concerns about similar outcomes in humans. Microplastics are ubiquitous in the environment, commonly found disposed in landfills and waste sites. Within indoor environments, the common sources are synthetic textiles, plastic bottles, and packaging. From the various point sources, they are globally distributed through air and water and can enter humans through various pathways. The finding of microplastics in fresh snow in the Antarctic highlights just how widely they are dispersed. The behaviour and health risks from microplastic particles are strongly influenced by their physicochemical properties, which is why their surfaces are important. Surface interactions are also important in pollutant transport via adsorption onto the microplastic particles. Our review covers the latest findings in microplastics research including the latest statistics in their abundance, their occurrence and fate in the environment, the methods of reducing microplastics exposure and their removal. We conclude by proposing future research directions into more effective remediation methods including new technologies and sustainable green remediation methods that need to be explored to achieve success in microplastics removal from waters at large scale.

Hydrothermal carbonisation of polyvinyl chloride in ethanol-water/water system for solid fuels: Dechlorination, characteristics analysis of hydrochar, and reaction path

Polyvinyl chloride (PVC) waste plastic is a typical solid waste. In this paper, the dechlorination and carbonization behavior of PVC in ethanol-water/water system under different process parameters (temperature, residence time, solid-liquid ratio) was studied, and hydrothermal carbon was characterized by SEM, elemental analysis, TG-DTG, XPS, Py-GC/MS. The results show that temperature is the key to the hydrothermal dechlorination of PVC, and the dechlorination efficiency of PVC is the highest by parameter optimization (220°C-90 min-10% S/D-80% E/D), which can reach 96.33 %. With the removal of Cl, the surface of the PVC matrix changed from full and smooth flocculent to honeycomb with uniform pore size distribution. Thermogravimetric analysis shows that the combustion of hydrochar can be divided into three stages: HCl precipitation and volatile combustion, semi-coke and coke combustion, and fixed carbon combustion. The combustion parameters and kinetic parameters of hydrochar were measured, and it was found that the hydrothermal carbonization of PVC at higher temperatures and ethanol-water ratio could improve the combustion performance of hydrochar. The highest calorific value can reach 36.68 MJ/mol. Py-GC/MS analyzed the distribution of the pyrolysis products, and alkylbenzene and aliphatic were the main products of pyrolysis. The structural analysis of hydrochar showed that C-C and CC accounted for the largest proportion, accompanied by a small amount of C-O and CO and trace C-Cl. The possible reaction mechanism of the hydrothermal carbonization of PVC was analyzed based on the distribution of functional groups and compound composition. This work provides an effective and sustainable method for the recycling of refractory chlorinated plastics.

Characterization of the microplastic photoaging under the action of typical salt ions of biological nitrogen removal processes

Microplastics (MPs) are one of the most prevalent and diverse contaminants, and wastewater treatment plants are significant MP aggregators. Controlling the pollution caused by microplastics requires an understanding of how they age. The properties of the MPs photoaging process under the influence of salt ions typical of biological nitrogen elimination processes were disclosed in this work. The aging process of polyvinyl chloride microplastics (PVC-MPs) was greatly slowed down by greater HCO3- and NO2- concentrations, according to a comparison of the carbonyl index changes that occurred during photoaging. The carbonyl index had a negative correlation with the thermal stability of the photo-aged PVC-MPs, and aging accelerated the elimination of chlorine from the water. The samples were aged by UV radiation after 36 h at 40 °C, and the amount of chlorine eliminated was 10.13 times greater than that of the original MPs samples. It was discovered that the leachate concentration of aged MPs dramatically increased with decreasing particle size and was positively connected with the level of aging by comparing the concentration of leachate for two particle sizes (1 mm and 100 m). Photoaging caused MPs to become rougher, which in turn improved the NO3--N, NH4+-N, and NO2--N adsorption by PVC-MPs.

Catalytic stepwise pyrolysis for dechlorination and chemical recycling of PVC-containing mixed plastic wastes: Influence of temperature, heating rate, and catalyst

The viability of pyrolysis technology for chemical recycling of plastics is challenged by the presence of PVC in real-world mixed plastic wastes. This study aims to investigate catalytic stepwise pyrolysis as a pretreatment step to remove chlorine from PVC-containing plastic wastes prior to further processing. TG-FTIR and Py-GCMS analysis as well as experiments on a lab-scale pyrolysis system were conducted to study the influence of key processing parameters on the pretreatment including temperature, heating rate, and catalysts. Py-GCMS results indicated 300 °C to be the best pretreatment temperature in terms of balancing Cl removal and avoidance of organochloride formation. Metal oxides, i.e., CaO and Fe2O3, mainly acted as adsorbents of HCl gases with little cracking effect, and their adsorption effects are positively correlated with alkalinity. ZSM-5 catalysts promoted the release of HCl, and the dechlorination effect was more pronounced with ZSM-5 of higher acidity. In contrast, in the lab-scale pyrolysis system, 350 °C pretreatment achieved the highest HCl generation ratio, i.e., 43.60 %. The addition of zeolite catalyst significantly reduced the content of organochloride in the pyrolysis oil in contrast to the performance of metal oxides, but also absorbed most HCl instead of promoting HCl release as in Py-GCMS tests. Mass balance analyses revealed that the majority of chlorine was retained in the solid residues following the catalytic stepwise pyrolysis process, with the notable exception of Fe2O3. ZSM-5(25) catalyst combined with 350 °C pretreatment temperature and 550 °C final pyrolysis achieved the lowest chlorine content in the pyrolysis oil, i.e., 20 ppm, among different process conditions.

Water retention and hydraulic properties of a natural soil subjected to microplastic contaminations and leachate exposures

The influences of microplastics (MPs) contamination on soils have been extensively studied recently. Most of previous studies focus on saturated hydraulic conductivities and water retention of loose soils under laboratory conditions. The effects of MPs on the hydraulic properties of compacted soils for engineering purposes have not been well understood. This paper presents the laboratory investigation of water retention capacity, saturated (ksat) and unsaturated (kθ) hydraulic conductivities of a compacted natural soil contaminated by MPs and exposed to fresh, medium-aged, and stabilized leachates. The saturated (kg) and unsaturated air conductivities (kgθ) are calculated. The MPs with maximum particle sizes of 500, 150 and 50 μm were added to soils to obtain samples with mass ratios of 0.5, 1.0, 2.0, and 5.0 %, respectively. Under similar ranges of dry densities, permeation of fresh leachates decreases ksat of the compacted soils by 30 % while exposure to stabilized leachates increases ksat by 10 %, due to the viscosities of liquids. The flow channel properties of the compacted soils contaminated with different sizes and concentrations of MPs vary. The most complex flow channel can be found in samples with 5 % 50 μm MPs. The inclusions of MPs decrease residual moisture contents of the compacted soils regardless of MP sizes and percentages. The effects of MPs on air-entry pressures and parameter n depend on the sizes of MPs. The kθ (kgθ) of compacted soils with MPs depend on the combined effects of ksat (kg) and tortuosity parameter (l). Though l ranges from -0.85 to 2.12 with different levels of MP exposures, it does not have a significant influence on the relative hydraulic (kθ/ksat) and air conductivities (kgθ/kg) of the compacted soils. Future studies can focus on the long-term hydraulic properties of soils under MP contamination.

Sources, Degradation, Ingestion and Effects of Microplastics on Humans: A Review

Celluloid, the predecessor to plastic, was synthesized in 1869, and due to technological advancements, plastic products appear to be ubiquitous in daily life. The massive production, rampant usage, and inadequate disposal of plastic products have led to severe environmental pollution. Consequently, reducing the employment of plastic has emerged as a pressing concern for governments globally. This review explores microplastics, including their origins, absorption, and harmful effects on the environment and humans. Several methods exist for breaking down plastics, including thermal, mechanical, light, catalytic, and biological processes. Despite these methods, microplastics (MPs, between 1 and 5 mm in size) continue to be produced during degradation. Acknowledging the significant threat that MPs pose to the environment and human health is imperative. This form of pollution is pervasive in the air and food and infiltrates our bodies through ingestion, inhalation, or skin contact. It is essential to assess the potential hazards that MPs can introduce. There is evidence suggesting that MPs may have negative impacts on different areas of human health. These include the respiratory, gastrointestinal, immune, nervous, and reproductive systems, the liver and organs, the skin, and even the placenta and placental barrier. It is encouraging to see that most of the countries have taken steps to regulate plastic particles. These measures aim to reduce plastic usage, which is essential today. At the same time, this review summarizes the degradation mechanism of plastics, their impact on human health, and plastic reduction policies worldwide. It provides valuable information for future research on MPs and regulatory development.

Characterization of solid and liquid carbonization products of polyvinyl chloride (PVC) and investigation of the PVC-derived adsorbent for the removal of organic compounds from water

The transformation of plastic wastes into value-added carbon materials is a promising strategy for the recycling of plastics. Commonly used polyvinyl chloride (PVC) plastics are converted into microporous carbonaceous materials using KOH as an activator via simultaneous carbonization and activation for the first time. The optimized spongy microporous carbon material has a surface area of 2093 m² g^-1 and a total pore volume of 1.12 cm³ g^-1, and aliphatic hydrocarbons and alcohols are yielded as the carbonization by-products. The PVC-derived carbon materials exhibit outstanding adsorption performance for removing tetracycline from water, and the maximum adsorption capacity reaches 1480 mg g^-1. The kinetic and isotherm patterns for tetracycline adsorption follow the pseudo-second-order and Freundlich models, respectively. Adsorption mechanism investigation indicates that pore filling and hydrogen bond interaction are mainly responsible for the adsorption. This study provides a facile and environmentally friendly approach for valorizing PVC into adsorbents for wastewater treatment.

Nanoplastics are significantly different from microplastics in urban waters

Microplastics (MPs) and nanoplastics (NPs) are ubiquitous and intractable in urban waters. Compared with MPs, the smaller NPs have shown distinct physicochemical features, such as Brownian motion, higher specific surface area, and stronger interaction with other pollutants. Therefore, the qualitative and quantitative analysis of NPs is more challenging than that of MPs. Moreover, these characteristics endow NPs with significantly different environmental fate, interactions with pollutants, and eco-impacts from those of MPs in urban waters. Herein, we critically analyze the current advances in the difference between MPs and NPs in urban waters. Analytical challenges, fate, interactions with surrounding pollutants, and eco-impacts of MPs and NPs are comparably discussed., The characterizations and fate studies of NPs are more challenging compared to MPs. Furthermore, NPs in most cases exhibit stronger interactions with other pollutants and more adverse eco-impacts on living things than MPs. Subsequently, perspective in this field is proposed to stimulate further size-dependent studies on MPs and NPs. This review would benefit the understanding of the role of NPs in the urban water ecosystem and guide future studies on plastic pollution management.

Effect of lithological properties of beach sediments on plastic pollution in Bodrum Peninsula (SW Türkiye)

The effects grain size on transport and retention of plastics in sediments are controversial issue. Four beaches were selected on the Bodrum Peninsula (SW Türkiye) for this study. Twenty-four samples with poorly to well sorted, sandy gravel, gravel, or gravelly sand were collected from the top five cm of the sampling quadrant's four corners and center of 1 m² area, from shoreline and backshore. The highest plastic content (38 mesoplastics/600 g - 455 microplastics (MPs)/1200 g) was determined on the Bodrum Coast having the highest population. Polyethylene (PE), polypropylene (PP), polyvinyl chloride (PVC), polystyrene (PS), polyethylene terephthalate (PET) and polyurethane (PU) were predominantly detected with Fourier Transform Infrared Spectroscopy (FTIR) analysis as MPs as a fragment and fiber. This study indicates the negative correlation between grain size and the number of MPs in coastal sediments. Anthropogenic activities are evaluated as a possible primary source of plastic pollution in the study area.

Pyrolysis behavior, kinetics, and thermodynamics of waste pharmaceutical blisters under CO2 atmosphere

The disastrous impact of COVID-19 pandemic has caused a significantly increased production and use of pharmaceutical drugs, which is accompanied by the rapid generation of waste pharmaceutical blisters (WPBs). Nonetheless, its treatment has not gained appropriate attentions and a perceptible process development was not achieved. In this study, the WPBs pyrolysis in CO₂ atmosphere was conducted as well as the thermodynamics and kinetics were investigated. The thermogravimetric analysis revealed that the WPBs decomposition could be divided into two stages of 25 - 365 °C and 365 - 900 °C with mass loss of 56.5 - 60.5 wt% and 22.5 - 25.9 wt%, respectively. Fourier-transform infrared spectroscopy analysis indicated the dechlorination process initiating at ∼300 °C. The simultaneous asymmetric stretching of HCl and stretching vibration of C-Cl bond was detected in the range of 2600 - 3250 cm^-1 and 660 - 750 cm^-1, respectively. The dechlorination reactions were almost complete at ∼520 °C and minor peaks (2900 -3100 cm^-1) due to C-H vibrations were observed. Gas chromatography-mass spectrometry analysis indicated that the evolved products included alkanes, benzene, olefin, as well as HCl. The cycloalkenes content significantly increased during the second conversion stage, implying the addition reactions between alkanes and olefins. The apparent activation energy was calculated using three model-free methods and the values from Flynn-Wall-Ozawa model increased from 142.0 to 255.8 kJ·mol^-1 with an average value of 147.4 kJ·mol^-1. The methods of Coats-Redfern as well as Malek were applied to determine the reaction mechanism. The one-dimensional diffusion model was more reliable to describe the WPBs pyrolysis. This study will represent a significant reference case for the thermochemical conversion of multilayer packing waste and facing the increasing demand for the medical waste recycling.