Graphene oxide based heterojunction TiO 2 –ZnO catalysts with outstanding photocatalytic performance for bisphenol-A, ibuprofen and flurbiprofen

ZnO nanostructured matrix as nexus catalysts for the removal of emerging pollutants

Water pollution stands as a pressing global environmental concern, elevating the significance of innovative, dependable, and sustainable solutions. This study represents an extensive review of the use of photocatalytic zinc oxide nanoparticles (ZnO NPs) for the removal of emerging pollutants from water and wastewater. The study examines ZnO NPs' different preparation methods, including physical, chemical, and green synthesis, and emphasizes on advantages, disadvantages, preparation factors, and investigation methods for the structural and morphological properties. ZnO NPs demonstrate remarkable properties as photocatalysts; however, their small dimensions pose an issue, leading to potential post-use environmental losses. A strategy to overcome this challenge is scaling up ZnO NP matrices for enhanced stability and efficiency. The paper introduces novel ZnO NP composites, by incorporating supports like carbon and clay that serve as photocatalysts in the removal of emerging pollutants from water and wastewater. In essence, this research underscores the urgency of finding innovative, efficient, and eco-friendly solutions for the removal of emerging pollutants from wastewater and highlights the high removal efficiencies obtained when using ZnO NPs obtained from green synthesis as a photocatalyst. Future research should be developed on the cost-benefit analysis regarding the preparation methods, treatment processes, and value-added product regeneration efficiency.

Computational explorations of the interaction between laccase and bisphenol A: influence of surfactant and different organic solvents

Bisphenol A (BPA), as an environmental endocrine disruptor can cause damage to the reproductive, nervous and immune systems. Laccase can be used to degrade BPA. However, laccase is easily deactivated, especially in organic solvents, but the specific details are not clear. Molecular dynamics simulations were used to investigate the reasons for changes in laccase activity in acetonitrile (ACN) and dimethyl formamide (DMF) solutions. In addition, the effects of ACN and DMF on the activity of laccase and surfactant rhamnolipid (RL) on the degradation of BPA by laccase were investigated. Results showed that addition of ACN changed the structure of the laccase, not only decreasing the van der Waals interaction that promoted the binding of laccase with BPA, but also increasing the polar solvation free energy that hindered the binding of laccase with BPA, so it weakened the laccase activity. DMF greatly enhanced the van der Waals interaction between laccase and BPA, and played a positive role in their binding. The addition of surfactant RL alleviated the effect of organic solvent on the activity of laccase by changing the polar solvation energy. The mechanism of surfactant RL affecting laccase activity in ACN and DMF is described, providing support for understanding the effect of organic solvents on laccase.

Reaction Steps in Heterogeneous Photocatalytic Oxidation of Toluene in Gas Phase-A Review

A review of the current literature shows there is no clear consensus regarding the reaction mechanisms of air-borne aromatic compounds such as toluene by photocatalytic oxidation. Potential oxidation reactions over TiO2 or TiO2-based catalysts under ultraviolet and visible (UV/VIS) illumination are most commonly considered for removal of these pollutants. Along the pathways from a model pollutant, toluene, to final mineralization products (CO2 and H2O), the formation of several intermediates via specific reactions include parallel oxidation reactions and formation of less-reactive intermediates on the TiO2 surface. The latter may occupy active adsorption sites and causes drastic catalyst deactivation in some cases. Major hazardous gas-phase intermediates are benzene and formaldehyde, classified by the International Agency for Research on Cancer (IARC) as Group 1 carcinogenic compounds. Adsorbed intermediates leading to catalyst deactivation are benzaldehyde, benzoic acid, and cresols. The three most typical pathways of toluene photocatalytic oxidation are reviewed: methyl group oxidation, aromatic ring oxidation, and aromatic ring opening.

Adsorption Performance of Magnetic Covalent Organic Framework Composites for Bisphenol A and Ibuprofen

As typical environmental endocrine disruptors and nonsteroidal anti-inflammatory drugs, bisphenol A and ibuprofen in water supplies can cause great harm to the ecological environment and human health. In this study, magnetic covalent organic framework composites Fe₃O₄@COF-300 were synthesized by the hydrothermal method and used to remove bisphenol A and ibuprofen from water. Fe₃O₄@COF-300 could be rapidly separated from the matrix by external magnetic fields, and could selectively adsorb bisphenol A and ibuprofen in the presence of coexisting compounds such as phenol, Congo red, and amino black 10B. The removal efficiency of ibuprofen was 96.12-98.52% at pH in the range of 2-4 and that of bisphenol A was 92.18-95.62% at pH in the range of 2-10. The adsorption of bisphenol A and ibuprofen followed a pseudo-second-order kinetic and Langmuir model, and was a spontaneous endothermic process with the maximum adsorption amounts of 173.31 and 303.03 mg∙g^-1, respectively. The material presented favorable stability and reusability, and the removal efficiency of bisphenol A and ibuprofen after 5 cycles was still over 92.15% and 89.29%, respectively. Therefore, the prepared composite Fe₃O₄@COF-300 exhibited good performance in the adsorption of bisphenol A and ibuprofen in water.

Hybrid Metal Oxide/Biochar Materials for Wastewater Treatment Technology: A Review

This paper discusses the properties of metal oxide/biochar systems for use in wastewater treatment. Titanium, zinc, and iron compounds are most often combined with biochar; therefore, combinations of their oxides with biochar are the focus of this review. The first part of this paper presents the most important information about biochar, including its advantages, disadvantages, and possible modification, emphasizing the incorporation of inorganic oxides into its structure. In the next four sections, systems of biochar combined with TiO₂, ZnO, Fe₃O₄, and other metal oxides are discussed in detail. In the next to last section probable degradation mechanisms are discussed. Literature studies revealed that the dispersion of a metal oxide in a carbonaceous matrix causes the creation or enhancement of surface properties and catalytic or, in some cases, magnetic activity. Addition of metallic species into biochars increases their weight, facilitating their separation by enabling the sedimentation process and thus facilitating the recovery of the materials from the water medium after the purification process. Therefore, materials based on the combination of inorganic oxide and biochar reveal a wide range of possibilities for environmental applications in aquatic media purification.

Pharmaceuticals in the Aquatic Environment: A Review on Eco-Toxicology and the Remediation Potential of Algae

The pollution of the aquatic environment has become a worldwide problem. The widespread use of pesticides, heavy metals and pharmaceuticals through anthropogenic activities has increased the emission of such contaminants into wastewater. Pharmaceuticals constitute a significant class of aquatic contaminants and can seriously threaten the health of non-target organisms. No strict legal regulations on the consumption and release of pharmaceuticals into water bodies have been implemented on a global scale. Different conventional wastewater treatments are not well-designed to remove emerging contaminants from wastewater with high efficiency. Therefore, particular attention has been paid to the phycoremediation technique, which seems to be a promising choice as a low-cost and environment-friendly wastewater treatment. This technique uses macro- or micro-algae for the removal or biotransformation of pollutants and is constantly being developed to cope with the issue of wastewater contamination. The aims of this review are: (i) to examine the occurrence of pharmaceuticals in water, and their toxicity on non-target organisms and to describe the inefficient conventional wastewater treatments; (ii) present cost-efficient algal-based techniques of contamination removal; (iii) to characterize types of algae cultivation systems; and (iv) to describe the challenges and advantages of phycoremediation.

Synthesis, Performance Measurement of Bi2SmSbO7/ZnBiYO4 Heterojunction Photocatalyst and Photocatalytic Degradation of Direct Orange within Dye Wastewater under Visible Light Irradiation

Originally, the new catalyst Bi2SmSbO7 was synthesized by the hydrothermal synthesis method or by the solid-phase sintering method at a lofty temperature. A solvothermal method was utilized to prepare a Bi2SmSbO7/ZnBiYO4 heterojunction photocatalyst (BZHP). The crystal structure of Bi2SmSbO7 belonged to the pyrochlore structure and face-centered cubic crystal system by the space group of Fd3m. The cell parameter a was equivalent to 10.835(1) Å (Bi2SmSbO7). With Bi2SmSbO7/ZnBiYO4 heterojunction (BZH) as the photocatalyst, the removal rate (RR) of direct orange (DO) and the total organic carbon were 99.10% and 96.21% after visible light irradiation of 160 min (VLI-160M). The kinetic constant k toward DO concentration and visible light irradiation time (VLI) with BZH as photocatalyst reached 2.167 min−1. The kinetic constant k, which was concerned with total organic carbon, reached 0.047 min−1. The kinetic curve that came from DO degradation with BZH as a catalyst under VLI conformed to the second-order reaction kinetics. After VLI-160M, the photocatalytic degradation (PD) removal percentage of DO with BZH as the photocatalyst was 1.200 times, 1.268 times or 3.019 times that with Bi2SmSbO7 as the photocatalyst, ZnBiYO4 as the photocatalyst or with nitrogen-doped titanium dioxide as the photocatalyst. The photocatalytic activity (PA) was as following: BZH > Bi2SmSbO7 > ZnBiYO4 > nitrogen-doped titanium dioxide. After VLI-160M for three cycles of experiments with BZH as the photocatalyst, the RR of DO reached 98.03%, 96.73% and 95.43%, respectively, which meant that BZHP possessed high stability. By using the experiment of adding a trapping agent, the oxidative purifying capability for degradation of direct orange, which was in gradual depressed order, was as following: hydroxyl radical > superoxide anion > holes. Finally, the possible degradation pathway and degradation mechanism of DO were discussed systematically. A new high active heterojunction catalyst BZHP, which could efficiently remove toxic organic pollutants such as DO from dye wastewater after VLI, was obtained. Our research was meant to improve the photocatalytic property of the single photocatalyst.

Molybdenum Modified Sol–Gel Synthesized TiO2 for the Photocatalytic Degradation of Carbamazepine under UV Irradiation

Pharmaceutical CEC compounds are a potential threat to man, animals, and the environment. In this study, a sol–gel-derived TiO2 (SynTiO2) was produced and subsequently sonochemically doped with a 1.5 wt% Mo to obtain the final product (Mo (1.5 wt%)/SynTiO2). The as-prepared materials were characterized for phase structure, surface, and optical properties by XRD, TEM, N2 adsorption–desorption BET isotherm at 77 K, and PSD by BJH applications, FTIR, XPS, and UV-Vis measurements in DRS mode. Estimated average crystallite size, particle size, surface area, pore-volume, pore size, and energy bandgap were 16.10 nm, 24.55 nm, 43.30 m2/g, 0.07 cm3/g, 6.23 nm, and 3.05 eV, respectively, for Mo/SynTiO2. The same structural parameters were also estimated for the unmodified SynTiO2 with respective values of 14.24 nm, 16.02 nm, 133.87 m2/g, 0.08 cm3/g, 2.32 nm, and 3.3 eV. Structurally improved (Mo (1.5 wt%)/SynTiO2) achieved ≈100% carbamazepine (CBZ) degradation after 240 min UV irradiation under natural (unmodified) pH conditions. Effects of initial pH, catalyst dosage, initial pollutant concentration, chemical scavengers, contaminant ions, hydrogen peroxide (H2O2), and humic acid (HA) were also investigated and discussed. The chemical scavenger test was used to propose involved photocatalytic degradation process mechanism of CBZ.

Adsorptive and photocatalytic remediation of hazardous organic chemical pollutants in aqueous medium: A review

The provision of clean water is still a major challenge in developing parts of the world, as emphasized by the United Nation Sustainable Development Goals (SDG 6), and has remained a subject of extensive research globally. Advancements in science and industry have resulted in a massive surge in the amount of industrial chemicals produced within the last few decades. Persistent and emerging organic pollutants are detected in aquatic environments, and conventional wastewater treatment plants have ineffectively handled these trace, bioaccumulative and toxic compounds. Therefore, we have conducted an extensive bibliometric analysis of different materials utilized to combat organic pollutants via adsorption and photocatalysis. The classes of pollutants, material synthesis, mechanisms of interaction, merits, and challenges were comprehensively discussed. The paper highlights the advantages of various materials used in the removal of hazardous pollutants from wastewater with activated carbon having the highest adsorption capacity. Dyes, pharmaceuticals, endocrine-disrupting chemicals, pesticides and other recalcitrant organic pollutants have been successfully removed at high degradation efficiencies through the photocatalytic process. The photocatalytic degradation and adsorption processes were compared by considering factors such as cost, efficiency, ease of application and reusability. This review will be good resource material for water treatment professionals/scientists, who may be interested in adsorptive and photocatalytic remediation of organic chemicals pollutants.

Preparation and Characterization of Supported Molybdenum Doped TiO2 on α-Al2O3 Ceramic Substrate for the Photocatalytic Degradation of Ibuprofen (IBU) under UV Irradiation

TiO2-based photocatalyst materials have been widely studied for the abatement of contaminants of emerging concerns (CECs) in water sources. In this study, 1.5 wt% Mo-doped HRTiO2 was obtained by the sonochemical method. The material was analyzed and characterized for thermal, structural/textural, morphological, and optical properties using TGA-DSC, XRD, TEM, FTIR, XPS, SEM-EDS, BET (N2 adsorption-desorption measurement and BJH application method), and UV-Vis/DRS measurement. By the dip-coating technique, ~5 mg of Mo/HRTiO2 as an active topcoat was deposited on ceramic. In suspension and for photocatalyst activity performance evaluation, 1 g/L of 1.5 wt% (Mo)/HRTiO2 degraded ~98% of initial 50 mg/L IBU concentration after 80 min of 365 nm UV light irradiation and under natural (unmodified) pH conditions. Effects of initial pH condition, catalyst dosage, and initial pollutant concentration were also investigated in the photocatalyst activity performance in suspension. The photocatalyst test on the supported catalyst removed ~60% of initial 5mg/L IBU concentration, while showing an improved performance with ~90% IBU removal employing double and triple numbers of coated disk tablets. After three successive cycle test runs, XRD phase reflections of base TiO2 component of the active photocatalyst supported layer remained unchanged: An indication of surface coat stability after 360 min of exposure under 365 nm UV irradiation.

Nanophotocatalysis for the Removal of Pharmaceutical Residues from Water Bodies: State of Art and Recent Trends

Background:

The occurrence of pharmaceuticals in surface and drinking water is ubiquitous and is a major concern of researchers. These compounds cause a destructive impact on aquatic and terrestrial life forms, and the removal of these compounds from the environment is a challenging issue. Existent conventional wastewater treatment processes are generally inefficacious because of their low degradation efficiency and inadequate techniques associated with the disposal of adsorbed pollutants during comparatively effective methods like the adsorption process.

Remediation Method:

Semiconductor-mediated photocatalysis is an attractive technology for the efficient removal of pharmaceutical compounds. Among various semiconductors, TiO2 and ZnObased photocatalysts gained much interest during the last years because of their efficiency in decomposing and mineralizing the lethal organic pollutants with the utilization of UV-visible light. Incessant efforts are being undertaken for tuning the physicochemical, optical, and electronic properties of these photocatalysts to strengthen their overall photocatalytic performance with good recycling efficiency.

Results:

This review attempts to showcase the recent progress in the rational design and fabrication of nanosized TiO2 and ZnO photocatalysts for the removal of pollutants derived from the pharmaceutical industry and hospital wastes.

Conclusion:

Photocatalysis involving TiO2 and ZnO provides a positive impact on pollution management and could be successfully applied to remove pharmaceuticals from wastewater streams. Structure modifications, the introduction of heteroatoms, and the integration of polymers with these nano photocatalysts offer leapfrogging opportunities for broader applications in the field of photocatalysis.

Current advancements on the fabrication, modification, and industrial application of zinc oxide as photocatalyst in the removal of organic and inorganic contaminants in aquatic systems

Industrial wastewaters contain hazardous contaminants that pollute the environment and cause socioeconomic problems, thus demanding the employment of effective remediation procedures such as photocatalysis. Zinc oxide (ZnO) nanomaterials have emerged to be a promising photocatalyst for the removal of pollutants in wastewater owing to their excellent and attractive characteristics. The dynamic tunable features of ZnO allow a wide range of functionalization for enhanced photocatalytic efficiency. The current review summarizes the recent advances in the fabrication, modification, and industrial application of ZnO photocatalyst based on the analysis of the latest studies, including the following aspects: (1) overview on the properties, structures, and features of ZnO, (2) employment of dopants, heterojunction, and immobilization techniques for improved photodegradation performance, (3) applicability of suspended and immobilized photocatalytic systems, (4) application of ZnO hybrids for the removal of various types of hazardous pollutants from different wastewater sources in industries, and (5) potential of bio-inspired ZnO hybrid nanomaterials for photocatalytic applications using renewable and biodegradable resources for greener photocatalytic technologies. In addition, the knowledge gap in this field of work is also highlighted.

Nitrogen doped carbon spheres from Tamarindus indica shell decorated with vanadium pentoxide; photoelectrochemical water splitting, photochemical hydrogen evolution & degradation of Bisphenol A

At present energy and environmental remediation are of highest priority for the well defined sustainability. Multifunctional materials that solve both the issues are on high demand. In the present work, a simple method has been followed to extract carbon spheres fromTamarindus indica(commonly known astamarind fruit) shelland doped with nitrogen (N-CS). Vanadium pentoxide nanoflakes were decorated aroundN-CS and the resultant is labeled as V₂O₅/N-CS nanocomposite. The spectroscopic, microscopic, elemental mapping and x-ray photoelectron spectroscopic characterization confirm the nitrogen doping and formation of hybrid material. N-CS, V₂O₅, and V₂O₅/N-CS nanocompositehave been evaluated for their efficiency to evolve hydrogen and for degradation of Bisphenol A (BPA) under visible light. In addition, electrocatalytic hydrogen evolution in presence of light has also been evaluated. The DRS spectrum proves the decrease in the bandgap of V₂O₅ upon its decoration around N-CS material. In a photochemical experiment, the V₂O₅/N-CS nanocomposite evolved 18,600 μmolg^-1 of H_2.Electrochemical hydrogen evolution has also been evaluated in presence of light and obtained the onset potential of -60mV with 52 mV dec^-1 Tafel slope value. Scavenger studies indicate superoxide radicals and hydroxyl radicals are the active species responsible for the degradation of BPA. BPA degradation pathway has been predicted with the support of LC-MS results of the intermediates. All these results indicate the synthesized nanocomposite could be an efficient, stable multifunctional material for photocatalytic applications.

rGO Functionalized ZnO–TiO2 Core-Shell Flower-Like Architectures for Visible Light Photocatalysis

Core-shell heterostructures with a complex, flower-like morphology, comprising a ZnO core and a TiO2 shell decorated with reduced graphene oxide (rGO) sheets by hydrothermal wrapping, are reported to extend the absorption properties of the semiconductors toward the visible light range. The ternary photocatalysts were characterized by X-ray diffraction, field emission scanning electron microscopy, Raman spectroscopy, diffuse reflectance UV–Vis, and attenuated total reflectance-Fourier transform infrared spectroscopy. Its photocatalytic performance was evaluated under visible light irradiation using methylene blue dye as a model pollutant. The rGO-modified ZnO–TiO2 photocatalyst exhibited superior photoactivity compared to that of the parent ZnO–TiO2 core-shell structures, which was dependent on its graphene content. The enhanced photocatalytic response was attributed to the higher absorption in the visible light range, as well as the pronounced electron and hole separation in the ternary system.

Photocatalytic kinetics and cyclic stability of photocatalysts Fe-complex/TiO2 in the synergistic degradation of phenolic pollutants and reduction of Cr(VI)

In this paper, the kinetic characteristics and cycle stability of Fe-complex/TiO₂ in the process of degradation of phenolic pollutants and reduction of heavy metal Cr(VI) were studied systematically. First, the structural characteristics and photocatalytic activities of Fe(III)-(8-hydroxyquinoline-5-carboxylic acid)-TiO₂ (Fe-HQC-TiO₂) nanoparticle to degrade phenolic pollutants and reduce Cr(VI) simultaneously had been investigated. Compared with the single degradation, the efficiency of synergistic degradation/reduction had been improved and the degradation/reduction rate had been obviously accelerated. In particular, the cyclic stability of Fe-HQC-TiO₂ photocatalyst decreased obviously when it was used to reduce Cr(VI) alone, but it could still keep above 90% after three cycles when it was used for reduction of Cr(VI) and degradation of phenol synergistically. Second, to Fe-HQS/TiO₂ nanoparticle or Fe-HQS/TiO₂ nanotube (HQS (8-hydroxyquinoline-5-sulfonic acid)), the synergistic degradation/reduction (2,4-dichlorophenol/Cr(VI)) efficiencies were always greater than those of a single degradation/reduction and the time was greatly reduced. All the results indicated that there were interactions between Cr(VI) and phenol or 2,4-dichlorophenol in the photocatalytic process. The possible mechanism of synergistic accelerated degradation of phenolic compounds and reduction of Cr(VI) was proposed by analyzing and testing the surface characteristics of photocatalyst and the properties of photocatalytic system during the synergistic degradation/reduction.

Immobilized TiO2/ZnO Sensitized Copper (II) Phthalocyanine Heterostructure for the Degradation of Ibuprofen under UV Irradiation

Photocatalytic coatings of TiO2/ZnO/CuPc were developed on stainless steel substrates by subsequent sol gel dip coating for TiO2, spray pyrolysis for ZnO, and spin coating for copper (ii) phthalocyanine (CuPc) deposition. The latter compound was successfully prepared using a Schiff-based process. The materials and coatings developed were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy with attached energy dispersive spectroscopy (SEM-EDS), UV-Vis spectroscopy, room temperature photoluminescence (RTPL) spectroscopy, H1-nuclear magnetic resonance (1H-NMR) spectroscopy, C13-nuclear magnetic resonance (13C-NMR) spectroscopy, and matrix-assisted laser desorption/ionization-time of flight (MALDI-TOF) mass spectrometry (MS). The as-deposited TiO2/ZnO/CuPc on stainless steel retained in pristine state the structural and morphological/spectroscopic characteristics of its respective components. Estimated energy band gap values were 3.22 eV, 3.19 eV, 3.19 eV for TiO2, ZnO, TiO2/ZnO respectively and 1.60 eV, 2.44 eV, and 2.92 eV for CuPc. The photocatalytic efficiency of the fabricated TiO2/ZnO/CuPc coatings was tested toward ibuprofen (IBF). After 4 h irradiation under 365 nm UV, an increased degradation of about 80% was achieved over an initial 5 mg/L ibuprofen (IBF). This was much higher compared to about 42% and 18% IBF degradation by TiO2/ZnO and TiO2 thin film, respectively. In all cases, the stability of the best-performing photocatalyst was investigated showing a small decline to 77% of IBF degradation after the 5th cycle run. The effect of pH, reactive oxygen species (ROS) probe, shed light on a possible catalytic mechanism that was suggested.

Graphene-Based Composites as Catalysts for the Degradation of Pharmaceuticals

The incessant release of pharmaceuticals into the aquatic environment continues to be a subject of increasing concern. This is because of the growing demand for potable water sources and the potential health hazards which these pollutants pose to aquatic animals and humans. The inability of conventional water treatment systems to remove these compounds creates the need for new treatment systems in order to deal with these class of compounds. This review focuses on advanced oxidation processes that employ graphene-based composites as catalysts for the degradation of pharmaceuticals. These composites have been identified to possess enhanced catalytic activity due to increased surface area and reduced charge carrier recombination. The techniques employed in synthesizing these composites have been explored and five different advanced oxidation processes-direct degradation process, chemical oxidation process, photocatalysis, electrocatalyis processes and sonocatalytic/sono-photocatalytic processes-have been studied in terms of their enhanced catalytic activity. Finally, a comparative analysis of the processes that employ graphene-based composites was done in terms of process efficiency, reaction rate, mineralization efficiency and time required to achieve 90% degradation.

Polyaniline-Coated TiO2 Nanorods for Photocatalytic Degradation of Bisphenol A in Water

Polyaniline (PANI)-wrapped TiO₂ nanorods (PANI/TiO₂), obtained through the oxidative polymerization of aniline at the surface of hydrothermally presynthesized TiO₂ nanorods, were evaluated as photocatalysts for the degradation of Bisphenol A (BPA). Fourier-transform infrared spectroscopy analysis revealed the successful incorporation of PANI into TiO₂ by the appearance of peaks at 1577 and 1502 cm^-1 that are due to the C=C and C-N stretch of the benzenoid or quinoid ring in PANI. Brunauer-Emmett-Teller analysis revealed that PANI/TiO₂ had almost double the surface area of TiO₂ (44.8999 m²/g vs 28.2179 m²/g). Transmission electron microscopy (TEM) analysis showed that TiO₂ nanorods with different diameters were synthesized. The TEM analysis showed that a thin layer of PANI wrapped the TiO₂ nanorods. X-ray photon spectroscopy survey scan of the PANI/TiO₂ nanocomposite revealed the presence of C, O, Ti, and N. Photocatalytic activity evaluation under UV radiation through the effect of key parameters, including pH, contact time, dosage, and initial concentration of BPA, was carried out in batch studies. Within 80 min, 99.7% of 5 ppm BPA was attained using the 0.2 g/L PANI/TiO₂ photocatalyst at pH 10. The quantum yield (QY) of these photocatalysts was evaluated to be 9.86 × 10^-5 molecules/photon and 2.82 × 10^-5 molecules/photon for PANI/TiO₂ and TiO₂, respectively. PANI/TiO₂ showed better performance than as-synthesized TiO₂ with a rate constant of 4.46 × 10^-2 min^-1 compared to 2.18 × 10^-2 min^-1. The rate of degradation of PANI/TiO₂ was also superior to that of TiO₂ (150 mmol/g/h vs 74.89 mmol/g/h). Nitrate ions increased the rate of degradation of BPA, while humic acid consistently inhibited the degradation of BPA. LC-MS analysis identified degradation products with m/z 213.1, 135.1, and 93.1. The PANI/TiO₂ nanocomposite was reused up to five cycles with a removal of at least 80% in the fifth cycle. LC-MS results revealed three possible BPA degradation intermediates. LC-MS analysis identified degradation products which included protonated BPA, [C₁₄H₁₃O₂ ⁺], and [C₉H₁₁O⁺]. The PANI/TiO₂ nanocomposite demonstrated superior photocatalytic activity with respect to improved QY and figure of merit and lower energy consumption.

Recent Achievements in Development of TiO2-Based Composite Photocatalytic Materials for Solar Driven Water Purification and Water Splitting

Clean water and the increased use of renewable energy are considered to be two of the main goals in the effort to achieve a sustainable living environment. The fulfillment of these goals may include the use of solar-driven photocatalytic processes that are found to be quite effective in water purification, as well as hydrogen generation. H2 production by water splitting and photocatalytic degradation of organic pollutants in water both rely on the formation of electron/hole (e-/h+) pairs at a semiconducting material upon its excitation by light with sufficient photon energy. Most of the photocatalytic studies involve the use of TiO2 and well-suited model compounds, either as sacrificial agents or pollutants. However, the wider application of this technology requires the harvesting of a broader spectrum of solar irradiation and the suppression of the recombination of photogenerated charge carriers. These limitations can be overcome by the use of different strategies, among which the focus is put on the creation of heterojunctions with another narrow bandgap semiconductor, which can provide high response in the visible light region. In this review paper, we report the most recent advances in the application of TiO2 based heterojunction (semiconductor-semiconductor) composites for photocatalytic water treatment and water splitting. This review article is subdivided into two major parts, namely Photocatalytic water treatment and Photocatalytic water splitting, to give a thorough examination of all achieved progress. The first part provides an overview on photocatalytic degradation mechanism principles, followed by the most recent applications for photocatalytic degradation and mineralization of contaminants of emerging concern (CEC), such as pharmaceuticals and pesticides with a critical insight into removal mechanism, while the second part focuses on fabrication of TiO2-based heterojunctions with carbon-based materials, transition metal oxides, transition metal chalcogenides, and multiple composites that were made of three or more semiconductor materials for photocatalytic water splitting.

Recent developments and challenges in practical application of visible-light-driven TiO2-based heterojunctions for PPCP degradation: A critical review

The ability of the TiO₂-based photocatalysis process to mineralize organic pollutants has attracted attention worldwide for the degradation of recalcitrant pharmaceuticals and personal care products (PPCPs). Nevertheless, (1) the limited exploitation of the solar spectrum, i.e., activation under UV light (only 2-3% of solar spectrum), and (2) the high recombination rate of photo-generated charge carriers, i.e., electrons and holes, have limited its application which can, however, be improved by developing a TiO₂-based heterojunction. The objective of this critical review paper is to discuss the recent developments (2009-2019) in visible-light-driven (VLD) TiO₂-based heterojunctions for PPCP degradation and their degradation mechanisms. Compared to the conventional heterojunctions, Schottky and Z-scheme heterojunctions, which are non-conventional heterojunctions, are found to be more effective for PPCP degradation due to their more efficient separation of charge carriers and the occurrence of redox reactions at a relatively higher redox potential. Furthermore, the enhancement strategies for the development of a VLD TiO₂-based heterojunction are also explored which can be achieved by selecting the (1) highly photocatalytically active {001} facet of anatase TiO₂, (2) synthesis methods governing the structural changes at the junction interface, and (3) heterojunction components which can efficiently generate the powerful •OH radicals. The challenges in practical applications are also discussed which include factors, viz., cost reduction, recycling, stability, byproducts analysis, evaluation of the environmental effectiveness, and reactor design and scale-up of the VLD TiO₂-based heterojunctions. Accordingly, the prospects of VLD TiO₂-based heterojunctions for PPCP degradation in real environmental applications are discussed.

Reduced Graphene Oxide–P25 Nanocomposites as Efficient Photocatalysts for Degradation of Bisphenol A in Water

Reduced graphene oxide–titanium dioxide photocatalyst (rGO–TiO2) was successfully synthesized by the hydrothermal method. The rGO–TiO2 was used as photocatalyst for the degradation of bisphenol A (BPA), which is a typical endocrine disruptor of the environment. Characterization of photocatalysts and photocatalytic experiments under different conditions were performed for studying the structure and properties of photocatalysts. The characterization results showed that part of the anatase type TiO2 was converted into rutile type TiO2 after hydrothermal treatment and 1% rGO–P25 had the largest specific surface area (52.174 m2/g). Photocatalytic experiments indicated that 1% rGO–P25 had the best catalytic effect, and the most suitable concentration was 0.5 g/L. When the solution pH was 5.98, the catalyst was the most active. Under visible light, the three photocatalytic mechanisms were ranked as follows: O2•− > •OH > h+. 1% rGO–P25 also had strong photocatalytic activity in the photocatalytic degradation of BPA under sunlight irradiation. 1% rGO–P25 with 0.5 g/L may be a very promising photocatalyst with a variety of light sources, especially under sunlight for practical applications.

Promoting charge separation of biochar-based Zn-TiO2/pBC in the presence of ZnO for efficient sulfamethoxazole photodegradation under visible light irradiation

A novel and effective photocatalyst namely titanium dioxide doped with zinc elements stacked on reed straw biochar which was pretreated by acid (Zn-TiO₂/pBC) with visible light response was successfully prepared by a simple modified sol-gel method firstly. The prepared samples were characterized by scanning microscopy (SEM), energy dispersive X-ray spectrum (EDS), X-ray diffraction (XRD), nitrogen adsorption-desorption (BET) and UV-Vis diffuse reflectance spectra (DRS). The photocatalytic activity of Zn-TiO₂/pBC was further investigated through the photodegradation of sulfamethoxazole (SMX). Compared with TiO₂ and TiO₂/pBC, Zn-TiO₂/pBC had better photocatalytic activity under visible light due to zinc elements effectively inhibiting the agglomeration of TiO₂ and hindering the combination of photogenerated electrons and holes. The removal rate of SMX could reach 81.21%, which was 1.37 times higher than that of TiO₂/pBC(300). Three common anions (SO₄^2-, Cl^-, NO₃^-) existing in the Yellow River exhibited detrimental effects on the SMX photodegradation to a certain degree. It might mainly occurred hydroxylation, cleavage of SN bond and opening of isoxazole ring reactions during the photodegradation process of SMX. Meanwhile, there might be four main degradation pathways proposed throw the LC/MS/MS analysis. Finally, good reusability and stability illustrated Zn-TiO₂/pBC owned good practicality and feasibility for removal of organic pollutants in environment remediation area.

Photocatalytic decontamination of phenol and petrochemical wastewater through ZnO/TiO2 decorated on reduced graphene oxide nanocomposite: influential operating factors, mechanism, and electrical energy consumption

ZnO/TiO₂ anchored on a reduced graphene oxide (rGO) ternary nanocomposite heterojunction was synthesized via the multi-step method including hydrothermal, solvothermal and sol–gel methods. XRD, Raman, FESEM, EDX, Dot Mapping EDS, BET, FTIR, UV-VIS, TGA, and EIS techniques were utilized for characterizing as-synthesized catalysts. The XRD and Raman data proved the formation of anatase phase TiO₂ and wurtzite phase ZnO in the prepared samples. Further, the UV-Vis spectrum confirmed that the band gap value of ZnO/TiO₂ diminished on introduction of graphene oxide. Photocatalytic performance of the fabricated catalysts was investigated by decontamination of phenol in aqueous solutions. The effect of different operational factors such as pH, catalyst dosage, phenol concentration, and light illumination was investigated to find the optimum decontamination conditions. According to the results, complete degradation of phenol was achieved at pH = 4, catalyst dosage of 0.6 g L⁻¹, light intensity of 150 W, and phenol initial concentration of 60 ppm at 160 min under visible light illumination. With the addition of graphene oxide to the composite, a significant increase was detected in the photocatalytic performance due to the higher available surface area and lower electron/hole recombination rate. In addition, the scavenging experiments revealed that the ·OH is responsible for the degradation of phenol during the reaction. The degradation mechanism, economic performance, mineralization, and recyclability were also investigated. Kinetic studies confirmed that photocatalytic degradation process followed the pseudo-first-order kinetic model. A case of real wastewater treatment was used to examine the performance of the catalyst for real case studies.

ZnO/TiO₂ anchored on a reduced graphene oxide (rGO) ternary nanocomposite heterojunction was synthesized via the multi-step method including hydrothermal, solvothermal and sol–gel methods.