1
|
Pereira RM, Belli R, Lohbauer U, Hurle K, Campos TMB, Thim GP. Fatigue strength of bilayer yttria-stabilized zirconia after low-temperature degradation. J Mech Behav Biomed Mater 2024; 160:106725. [PMID: 39270447 DOI: 10.1016/j.jmbbm.2024.106725] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/01/2024] [Revised: 08/26/2024] [Accepted: 09/05/2024] [Indexed: 09/15/2024]
Abstract
This study examined the impact of interfacial interactions on bilayer yttria-stabilized zirconia (YSZ) used in dental restorations. In-house bilayer structures of 3YSZ and 5YSZ composition underwent hydrothermal degradation to compare the properties of control and low-temperature degradation (LTD) treated groups. Biaxial flexural strength via piston-on-three-balls, staircase fatigue strength over 106 cycles at 15 Hz, phase characterization and quantification through XRD and Rietveld refinement, and fractography were conducted. Weibull analysis was employed to determine the Weibull modulus and characteristic strength. Results demonstrated an enhancement in the mechanical performance of 3YSZ composition after LTD treatment, whereas the mechanical properties of 5YSZ remained largely unaffected post-degradation. Fractographic analysis revealed that failure originated at the surface tensile location across all specimen groups. These findings offer insights into the mechanical behavior of bilayer zirconia structures and reinforce the significance of hydrothermal treatment in enhancing their performance, particularly in the case of 3Y compositions.
Collapse
Affiliation(s)
- Raíssa Monteiro Pereira
- Laboratory of Plasma and Process, Technological Institute of Aeronautics, Praça Marechal Eduardo Gomes, 50, Vila das Acácias, São José dos Campos, SP, 12228-900, Brazil.
| | - Renan Belli
- Friedrich-Alexander-Universität Erlangen-Nürnberg (FAU), Forschungslabor für dentale Biomaterialien Zahnklinik 1 - Zahnerhaltung und Parodontologie, Glückstrasse 11, Erlangen, Germany
| | - Ulrich Lohbauer
- Friedrich-Alexander-Universität Erlangen-Nürnberg (FAU), Forschungslabor für dentale Biomaterialien Zahnklinik 1 - Zahnerhaltung und Parodontologie, Glückstrasse 11, Erlangen, Germany
| | - Katrin Hurle
- Friedrich-Alexander-Universität Erlangen-Nürnberg (FAU), GeoZentrum Nordbayern, Institut für Mineralogie, Schlossgarten 5a, 91054, Erlangen, Germany
| | - Tiago Moreira Bastos Campos
- Laboratory of Plasma and Process, Technological Institute of Aeronautics, Praça Marechal Eduardo Gomes, 50, Vila das Acácias, São José dos Campos, SP, 12228-900, Brazil
| | - Gilmar Patrocínio Thim
- Laboratory of Plasma and Process, Technological Institute of Aeronautics, Praça Marechal Eduardo Gomes, 50, Vila das Acácias, São José dos Campos, SP, 12228-900, Brazil
| |
Collapse
|
2
|
Carvalho LF, Bergamo ETP, Campos TMB, Fermino ES, Alves LMM, Benalcázar-Jalkh EB, Sousa EO, Coelho PG, Witek L, Tebcherani SM, Gierthmuehlen PC, Thim GP, Yamaguchi S, Carvalho AM, Bonfante EA. Characterization of a hydrothermally aged experimental alumina-toughened zirconia composite. Dent Mater 2024; 40:1464-1476. [PMID: 38945742 DOI: 10.1016/j.dental.2024.06.023] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/27/2024] [Revised: 06/12/2024] [Accepted: 06/14/2024] [Indexed: 07/02/2024]
Abstract
OBJECTIVES To assess the effects of different aging protocols on chemical, physical, and mechanical properties of an experimental ATZ composite compared to a zirconia. METHODS Disc-shaped specimens were obtained through uniaxial pressing of commercial powders (Tosoh), ATZ comprised of 80%ZrO2/20%Al2O3 (TZ-3YS20AB) and 3Y-TZP (3Y-SBE). The specimens of each material were divided into different groups according to the aging protocol: immediate, autoclave aging and hydrothermal reactor aging. The aging protocols were performed at 134 ºC for 20 h at 2.2 bar. Crystalline evaluations were performed using X-Ray Diffraction. The nanoindentation tests measured the elastic modulus (Em) and hardness (H). Biaxial flexural strength was performed, and Weibull statistics were used to determine the characteristic strength and Weibull modulus. The probability of survival was also determined. The Em and H data were analyzed by one-way ANOVA and Tukey test. RESULTS Diffractograms revealed the presence of monoclinic phase in both materials after aging. The hydrothermal reactor decreased the Em for ATZ compared to its immediate condition; and the H for both ATZ and 3Y-TZP regarding their immediate and autoclave aging conditions, respectively. The aging protocols significantly increased the characteristic strength for ATZ, while decreased for 3Y-TZP. No difference regarding Weibull modulus was observed, except for 3Y-TZP aged in reactor. For missions of up to 500 MPa, both materials presented a high probability of survival (>99 %) irrespective of aging condition. SIGNIFICANCE The synthesized ATZ composite exhibited greater physical and microstructural stability compared to 3Y-TZP, supporting potential application of the experimental material for long-span reconstructive applications.
Collapse
Affiliation(s)
- Laura F Carvalho
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry, University of Sao Paulo, Bauru 17012-901, SP, Brazil.
| | - Edmara T P Bergamo
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry, University of Sao Paulo, Bauru 17012-901, SP, Brazil
| | - Tiago M B Campos
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry, University of Sao Paulo, Bauru 17012-901, SP, Brazil
| | - Elisa S Fermino
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry, University of Sao Paulo, Bauru 17012-901, SP, Brazil
| | - Larissa M M Alves
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry, University of Sao Paulo, Bauru 17012-901, SP, Brazil; Laboratories for Microstructure Physics & Mechanics of Materials, Department of Preventive and Restorative Sciences, School of Dental Medicine, University of Pennsylvania, Philadelphia, PA 19104, USA
| | - Ernesto B Benalcázar-Jalkh
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry, University of Sao Paulo, Bauru 17012-901, SP, Brazil
| | - Edisa O Sousa
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry, University of Sao Paulo, Bauru 17012-901, SP, Brazil
| | - Paulo G Coelho
- DeWitt Daughtry Family Department of Surgery, Division of Plastic Surgery, Miller School of Medicine, University of Miami, Miami, FL 33136, USA; Department of Biochemistry and Molecular Biology, Miller School of Medicine, University of Miami, Miami, FL 33136, USA
| | - Lukasz Witek
- Biomaterials Division, NYU College of Dentistry, New York, NY 10010, USA; Department of Biomedical Engineering, NYU Tandon School of Engineering, New York University, Brooklyn, NY 11201, USA; Hansjörg Wyss Department of Plastic Surgery, NYU Grossman School of Medicine, New York, NY 10017, USA
| | - Sergio M Tebcherani
- Department of Production Engineering, Federal University of Technology, Ponta Grossa 84016-210, PR, Brazil
| | - Petra C Gierthmuehlen
- Department of Prosthodontics, Medical Faculty and University Hospital Düsseldorf, Heinrich-Heine-University, Düsseldorf, Germany
| | - Gilmar Patrocínio Thim
- Laboratory of Plasma and Process, Technological Institute of Aeronautics, São José dos Campos 12228-900, SP, Brazil
| | - Satoshi Yamaguchi
- Department of Dental Biomaterials, Osaka University Graduate School of Dentistry, Suita 565-0871, Osaka, Japan
| | - Alexandre M Carvalho
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry, University of Sao Paulo, Bauru 17012-901, SP, Brazil
| | - Estevam A Bonfante
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry, University of Sao Paulo, Bauru 17012-901, SP, Brazil
| |
Collapse
|
3
|
da Silva BCD, da Silva SEG, da Silva NR, de Moreira FGG, Souza KB, Zhang Y, de Souza ROA. Effect of different surface treatments and adhesive cementation on the surface topography and flexural strength of translucent and ultra-translucent monolithic zirconia. J Prosthodont 2024. [PMID: 39189693 DOI: 10.1111/jopr.13929] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/28/2024] [Accepted: 07/28/2024] [Indexed: 08/28/2024] Open
Abstract
PURPOSE To evaluate the effect of different surface treatments and adhesive cementation on the miniflexural strength (MFS) of monolithic zirconia. MATERIALS AND METHODS Two-hundred and forty (240) sintered bars of translucent zirconia (ZT) and ultra-translucent zirconia (ZUT) were obtained (8 mm ×2 mm ×1 mm). The bars were divided into 16 groups (n = 15) according to the factors "Zirconia" (ZT and ZUT), "Cementation" (Cem) and "surface treatment" (Ctrl:Control, Al:Aluminum oxide/Al2O3 50 µm, Si:Silica/SiO2 coated alumina particles oxide 30 µm, Gl:Glazing+hydrofluoric acid). Half of the bars received an adhesive layer application, followed by application of resin cement and light curing. The surface roughness was measured in non-cemented groups. All the bars were subjected to the MFS test (1.0 mm/min; 100 kgf). Scanning electron microscopy was used for qualitative analyses. MFS data (MPa) and roughness (µm) were statistically evaluated by three-way and two-way ANOVA respectively and Tukey's test (5%). RESULTS The surface treatment and the interaction were significant for roughness. Glazing promoted less roughness compared to silicatization. Regarding MFS, only the zirconia and surface treatment factors were significant. For ZT, the sandblasted groups had an increase in MFS and glazing reduced it. There was no difference between the groups without cementation for the ZUT; however, ZUT.Si/Cem, and ZUT.Al/Cem obtained superior MFS among the cemented groups. CONCLUSIONS Sandblasting increases the flexural strength for ZT, while glaze application tends to reduce it. Applying resin cement increases the flexural strength of ZUT when associated with sandblasting. Sandblasting protocols promote greater surface roughness.
Collapse
Affiliation(s)
| | - Sarah Emille Gomes da Silva
- Department of Dentistry, Federal University of Rio Grande do Norte (UFRN), Natal, Rio Grande do Norte, Brazil
| | - Nathália Ramos da Silva
- Department of Dentistry, Federal University of Rio Grande do Norte (UFRN), Natal, Rio Grande do Norte, Brazil
| | | | - Karina Barbosa Souza
- Institute of Science and Technology, Paulista State University (UNESP), São José dos Campos, São Paulo, Brazil
| | - Yu Zhang
- Department of Preventive and Restorative, University of Pennsylvania, School of Dental Medicine, Philadelphia, USA
| | - Rodrigo Othávio Assunção de Souza
- Department of Dentistry, Adjunct Professor in Prosthodontics, Federal University of Rio Grande do Norte (UFRN), Natal, Rio Grande do Norte, Brazil
| |
Collapse
|
4
|
Huang B, Chen M, Wang J, Zhang X. Advances in zirconia-based dental materials: Properties, classification, applications, and future prospects. J Dent 2024; 147:105111. [PMID: 38866229 DOI: 10.1016/j.jdent.2024.105111] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/14/2024] [Revised: 06/04/2024] [Accepted: 06/06/2024] [Indexed: 06/14/2024] Open
Abstract
OBJECTIVES Zirconia (ZrO2) ceramics are widely used in dental restorations due to their superior mechanical properties, durability, and ever-improving translucency. This review aims to explore the properties, classification, applications, and recent advancements of zirconia-based dental materials, highlighting their potential to revolutionize dental restoration techniques. STUDY SELECTION, DATA AND SOURCES The most recent literature available in scientific databases (PubMed and Web of Science) reporting advances of zirconia-based materials within the dental field is thoroughly examined and summarized, covering the major keywords "dental zirconia, classification, aesthetic, LTD, applications, manufacturing, surface treatments". CONCLUSIONS An exhaustive overview of the properties, classifications, and applications of dental zirconia was presented, alongside an exploration of future prospects and potential advances. This review highlighted the importance of addressing challenges such as low-temperature degradation resistance and optimizing the balance between mechanical strength and translucency. Also, innovative approaches to improve the performances of zirconia as dental material was discussed. CLINICAL SIGNIFICANCE This review provides a better understanding of zirconia-based dental biomaterials for dentists, helping them to make better choice when choosing a specific material to fabricate the restorations or to place the implant. Moreover, new generations of zirconia are still expected to make progress on key issues such as the long-term applications in dental materials while maintaining both damage resistance and aesthetic appeal, defining the directions for future research.
Collapse
Affiliation(s)
- Bo Huang
- State Key Laboratory of Oral Diseases & National Center for Stomatology & National Clinical Research Center for Oral Diseases & Department of Prosthodontics, West China Hospital of Stomatology, Sichuan University, Chengdu 610041, Sichuan, China
| | - Mengbing Chen
- State Key Laboratory of Oral Diseases & National Center for Stomatology & National Clinical Research Center for Oral Diseases & Department of Prosthodontics, West China Hospital of Stomatology, Sichuan University, Chengdu 610041, Sichuan, China
| | - Jian Wang
- State Key Laboratory of Oral Diseases & National Center for Stomatology & National Clinical Research Center for Oral Diseases & Department of Prosthodontics, West China Hospital of Stomatology, Sichuan University, Chengdu 610041, Sichuan, China.
| | - Xin Zhang
- State Key Laboratory of Oral Diseases & National Center for Stomatology & National Clinical Research Center for Oral Diseases & Department of Prosthodontics, West China Hospital of Stomatology, Sichuan University, Chengdu 610041, Sichuan, China.
| |
Collapse
|
5
|
Kwon WC, Park MG. Evaluation of mechanical properties of dental zirconia in different milling conditions and sintering temperatures. J Prosthet Dent 2023; 130:909-916. [PMID: 35115161 DOI: 10.1016/j.prosdent.2021.12.006] [Citation(s) in RCA: 1] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/02/2021] [Revised: 12/08/2021] [Accepted: 12/08/2021] [Indexed: 11/30/2022]
Abstract
STATEMENT OF PROBLEM The dry processing of zirconia has the disadvantage of dust dispersal during milling; thus, wet milling may be preferable. However, research on the mechanical properties of dental zirconia milled under different conditions and sintered at different temperatures is lacking. PURPOSE The purpose of this in vitro study was to evaluate changes in the mechanical properties of zirconia specimens after milling under dry and wet conditions at different sintering temperatures. MATERIAL AND METHODS Four hundred Ø20.0×1.5-mm presintered zirconia specimens were prepared by using a computer-aided design and computer-aided manufacturing (CAD-CAM) system and divided into 8 groups (n=50) based on the sintering (1230, 1330, 1430, and 1530 °C) and milling conditions (dry or wet). The mechanical properties (Vickers hardness, biaxial flexural strength, and fracture toughness) and physical properties (linear shrinkage and density) were examined. The microstructures of the specimens were observed with a scanning electron microscope. The crystal phases of the sintered green bodies were analyzed by using an X-ray diffractometer. The data were analyzed with descriptive statistics and 1-way and 2-way analyses of variance with Tukey HSD tests (α=.05). RESULTS The mechanical properties of all specimens increased with increasing sintering temperature, except for 1530 °C and the dry milling condition. The mechanical properties of the groups fabricated under wet milling conditions were better than those of the groups fabricated under dry milling conditions. Microscopic examination of the structure showed that the porosity decreased with increasing sintering temperature regardless of the milling conditions. CONCLUSIONS Higher sintering temperatures increased the mechanical properties (biaxial flexural strength, Vickers hardness, fracture toughness). However, phase transformation from tetragonal to cubic was observed for dry milled specimens sintered at 1530 °C, with decreased mechanical properties. Specimens fabricated by wet milling exhibited better mechanical properties than those fabricated by dry milling.
Collapse
Affiliation(s)
- Woo-Chang Kwon
- Interdisciplinary, Department for Advanced Innovative Manufacturing Engineering, Pusan National University, Busan, Republic of Korea
| | - Mi-Gyoung Park
- Professor and Chairman, Department of Dental Laboratory Science, College of Health Sciences, Catholic University of Pusan, Busan, Republic of Korea.
| |
Collapse
|
6
|
Piza MMT, Bergamo ETP, Campos TMB, Carvalho LF, Goulart CA, Gutierres E, Lopes ACO, Benalcazar Jalkh EB, Bonfante EA. Alumina-toughened zirconia nanocomposite: Aging effect on microstructural, optical, and mechanical properties. Dent Mater 2023; 39:1022-1031. [PMID: 37775460 DOI: 10.1016/j.dental.2023.09.005] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/13/2023] [Revised: 09/05/2023] [Accepted: 09/15/2023] [Indexed: 10/01/2023]
Abstract
OBJECTIVES To process an alumina-toughened zirconia (ATZ) nanocomposite and to characterize its crystalline phases, microstructure, residual stress, mechanical and optical properties before and after two different artificial aging methodologies. METHODS Disc-shaped specimens were obtained through uniaxial pressing of a commercial ATZ powder comprised of 80%ZrO2 / 20%Al2O3, with a particle size of 50 nm and 150 nm, respectively. Sintering was performed at 1500ºC for 2 h. Groups were established according to the aging protocol as immediate (ATZ-I) and aged either in autoclave (ATZ-A) or hydrothermal reactor (ATZ-R) at 134 ºC for 20 h at 2.2 bar. Crystalline phases and microstructure were assessed by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. Residual stress was evaluated by Raman spectroscopy. Contrast Ratio (CR) and Translucency Parameter (TP) were calculated to characterize optical properties. Mechanical properties were analyzed through Vickers microhardness, fracture toughness, and biaxial flexural strength test. RESULTS XRD spectra of both aging protocols revealed the presence of monoclinic zirconia (20-31%), where higher phase transformation was observed after aging in hydrothermal reactor. Optical properties evaluation demonstrated high opacity (CR: 0.99) and masking ability (TP: 0.26), with no significant differences after aging. Raman spectroscopy evidenced the presence of residual compressive stresses in the aged groups, being significantly higher for ATZ-R (-215.2 MPa). As-sintered specimens revealed hardness of ∼12.3 GPa and fracture toughness of ∼1.9 MPa.m1/2. Characteristic strength was 740 MPa for ATZ-I, 804 MPa for ATZ-A, and 879 MPa for ATZ-R, with significant differences between groups. Weibull modulus ranged from 16.5 to 18.8. All groups demonstrated high reliability up to 500 MPa stress missions (99-100%), with no significant differences after aging. SIGNIFICANCE The experimental ATZ nanocomposite presented high opacity and a high Weibull modulus. While aging created internal compressive stress responsible for an increase in characteristic strength, the nanocomposite was susceptible to hydrothermal degradation. Further studies are required to evaluate its degradation kinetics at low temperatures.
Collapse
Affiliation(s)
- Mariana M T Piza
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil.
| | - Edmara T P Bergamo
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Tiago M B Campos
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil; Department of Physics, Technological Institute of Aeronautics, São José dos Campos, SP, Brazil
| | - Laura F Carvalho
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Celso A Goulart
- São Paulo State University, School of Sciences and Engineering, Tupã, SP, Brazil
| | - Eliezer Gutierres
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Adolfo C O Lopes
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Ernesto B Benalcazar Jalkh
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Estevam A Bonfante
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| |
Collapse
|
7
|
Bonfante EA, Calamita M, Bergamo ETP. Indirect restorative systems-A narrative review. J ESTHET RESTOR DENT 2023; 35:84-104. [PMID: 36688803 DOI: 10.1111/jerd.13016] [Citation(s) in RCA: 5] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/28/2022] [Revised: 01/03/2023] [Accepted: 01/04/2023] [Indexed: 01/24/2023]
Abstract
OBJECTIVE The background and clinical understanding of the properties of currently available indirect restorative systems and fabrication methods is, along with manufacturer and evidence-based literature, an important starting point to guide the clinical selection of materials for tooth and/or implant supported reconstructions. Therefore, this review explores most indirect restorative systems available in the market, especially all-ceramic, along with aspects of manufacturing process, clinical survival rates, and esthetic outcomes. OVERVIEW Progressive incorporation of new technologies in the dental field and advancements in materials science have enabled the development/improvement of indirect restorative systems and treatment concepts in oral rehabilitation, resulting in reliable and predictable workflows and successful esthetic and functional outcomes. Indirect restorative systems have evolved from metal ceramics and polymers to glass ceramics, polycrystalline ceramics, and resin-matrix ceramics, aiming to improve not only biological and mechanical properties, but especially the optical properties and esthetic quality of the reconstructions, in attempt to mimic natural teeth. CONCLUSIONS Based on several clinical research, materials, and patient-related parameters, a decision tree for the selection of indirect restorative materials was suggested to guide clinicians in the rehabilitation process. CLINICAL SIGNIFICANCE The pace of materials development is faster than that of clinical research aimed to support their use. Since no single material provides an ideal solution to every case, professionals must continuously seek information from well designed, long-term clinical trials in order to incorporate or not new materials and technological advancements.
Collapse
Affiliation(s)
- Estevam A Bonfante
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of São Paulo, Bauru, SP, Brazil
| | - Marcelo Calamita
- Department of Restorative Dental Sciences at the University of Florida, Gainesville, Florida, USA
| | - Edmara T P Bergamo
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of São Paulo, Bauru, SP, Brazil
| |
Collapse
|
8
|
de Araújo-Júnior ENS, Bergamo ETP, Bastos TMC, Benalcázar Jalkh EB, Lopes ACO, Monteiro KN, Cesar PF, Tognolo FC, Migliati R, Tanaka R, Bonfante EA. Ultra-translucent zirconia processing and aging effect on microstructural, optical, and mechanical properties. Dent Mater 2022; 38:587-600. [PMID: 35272865 DOI: 10.1016/j.dental.2022.02.016] [Citation(s) in RCA: 9] [Impact Index Per Article: 4.5] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/26/2021] [Revised: 02/18/2022] [Accepted: 02/22/2022] [Indexed: 12/15/2022]
Abstract
OBJECTIVES To evaluate the effect of the ceramic processing and aging method on the microstructure, optical, and mechanical properties of a third generation ultra-translucent zirconia, yttria partially stabilized zirconia (5Y-PSZ). METHODS In-house discs were obtained through uniaxial and isostatic pressing an ultra-translucent Y-PSZ powder and sintering at 1450 °C for 2 h. As control, a commercial disc was milled from pre-sintered blocks fabricated with the same 5Y-PSZ powder through isostatic pressing and sintered under the same protocol. Discs were allocated into three groups according to aging condition as immediate (non-aged) and aged using autoclave or hydrothermal reactor at 134ºC for 20 h at 2.2 bar. Crystalline content and microstructure were evaluated using X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. Optical properties were determined using reflectance data to calculate the contrast ratio (CR) and translucency parameter (TP). Mechanical properties were assessed by Vickers hardness, fracture toughness and biaxial flexural strength tests. RESULTS XRD spectra revealed a prevalence of cubic (70%) and tetragonal (30%) phases, and the SEM images showed a dense fully crystalline ceramic matrix for both materials. Crystalline content and microstructure of the in-house and commercial 5Y-PSZs were not affected by aging. As-sintered 5Y-PSZs demonstrated similar CR (~0.6) and TP (~18) values, as well as Vickers hardness (~14 GPa) and fracture toughness (~3.8 Mpa.m1/2), with no significant alteration after both aging methods. In-house and commercial Y-PSZs Weibull moduli ranged from 3.0 to 5.3. 5Y-PSZ processing methods resulted in similar characteristic strength after sintering (592-618 Mpa). While commercial 5Y-PSZ showed no significant influence of aging on strength, hydrothermal reactor aging significantly decreased the in-house Y-PSZ characteristic strength (474 Mpa). Both 5Y-PSZs demonstrated high reliability up to 300-Mpa strength missions, with no detrimental effect of aging (88-100%). SIGNIFICANCE Irrespective of the processing method, ultra-translucent 5Y-PSZ showed high aging resistance and translucency stability, as well as strength corresponding to the indication up to short-span anterior prostheses.
Collapse
Affiliation(s)
- Everardo N S de Araújo-Júnior
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil.
| | - Edmara T P Bergamo
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Tiago M C Bastos
- Department of Physics, Technological Institute of Aeronautics, São José dos Campos, SP, Brazil
| | - Ernesto B Benalcázar Jalkh
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Adolfo C O Lopes
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Kelli N Monteiro
- Department of Biomaterial and Oral Biology, University of São Paulo, School of Dentistry, São Paulo, SP, Brazil
| | - Paulo F Cesar
- Department of Biomaterial and Oral Biology, University of São Paulo, School of Dentistry, São Paulo, SP, Brazil
| | - Fernanda C Tognolo
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Rafael Migliati
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Ricardo Tanaka
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Estevam A Bonfante
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| |
Collapse
|
9
|
Effect of finishing/polishing techniques and aging on topography, C. albicans adherence, and flexural strength of ultra-translucent zirconia: an in situ study. Clin Oral Investig 2022; 26:889-900. [PMID: 34448074 PMCID: PMC9902030 DOI: 10.1007/s00784-021-04068-3] [Citation(s) in RCA: 6] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/28/2020] [Accepted: 07/01/2021] [Indexed: 02/08/2023]
Abstract
OBJECTIVE To investigate the influence of different finishing/polishing techniques and in situ aging on the flexural strength (σ), surface roughness, and Candida albicans adherence of 5 mol% yttria-stabilized zirconia (ultratranslucent zirconia). MATERIALS AND METHODS A total of 120 zirconia bars (Prettau Anterior, Zirkonzahn) with dimensions of 8 × 2 × 0.5 mm were divided into 8 groups (n = 15) according to two factors: "in situ aging" (non-aged and aged (A)) and "finishing/polishing" (control (C), diamond rubber polishing (R), coarse grit diamond bur abrasion (B), and coarse grit diamond bur abrasion + diamond rubber polishing (BR)). Half of the samples from each group were subjected to a 60-day in situ aging by fixing the bars into cavities prepared in the posterior region of the base of complete or partial dentures of 15 patients. The samples were then subjected to the mini flexural (σ) test (1 mm/min). A total of 40 zirconia blocks (5 × 5 × 2 mm) were prepared and subjected to roughness (Ra) analyses and fungal adherence and complementary analyses (X-ray diffraction (XRD) and scanning electron microscopy (SEM)). The data of mean σ (MPa) and roughness Ra (μm) were statistically analyzed by two-way and one-way ANOVA, respectively, and Tukey's test. The Weibull analysis was performed for σ data. The fungal adhesion (Log CFU/mL) data were analyzed by Kruskal-Wallis tests. RESULTS For flexural resistance, the "finishing/polishing" factor was statistically significant (P = 0.0001); however, the "in situ aging" factor (P = 0.4458) was not significant. The non-aged (507.3 ± 115.7 MPa) and aged (487.6 ± 118.4 MPa) rubber polishing groups exhibited higher mean σ than the other techniques. The non-aged (260.2 ± 43.3 MPa) and aged (270.1 ± 48.8 MPa) bur abrasion groups presented lower σ. The coarse-grit diamond bur abrasion group (1.82 ± 0.61 µm) presented the highest roughness value (P = 0.001). Cell adhesion was not different among groups (P = 0.053). Group B presented the most irregular surface and the highest roughness Ra of 0.61 m. CONCLUSIONS The finishing of ultratranslucent zirconia might be preferably done with a diamond rubber polisher. Moreover, the protocols used did not interfere with Candida albicans adhesion. CLINICAL RELEVANCE Coarse-grit diamond burs might be avoided for finishing ultratranslucent monolithic zirconia, which might be preferably performed with a diamond rubber polisher.
Collapse
|
10
|
Bergamo ETP, Campos TMB, Lopes ACO, Cardoso KB, Gouvea MVR, de Araújo-Júnior ENS, Witek L, Gierthmühlen PC, Coelho PG, Benalcázar Jalkh EB, Zahoui A, de Carvalho LF, Bonfante EA. Hydrothermal aging affects the three-dimensional fit and fatigue lifetime of zirconia abutments. J Mech Behav Biomed Mater 2021; 124:104832. [PMID: 34536801 DOI: 10.1016/j.jmbbm.2021.104832] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/02/2021] [Revised: 09/05/2021] [Accepted: 09/07/2021] [Indexed: 11/30/2022]
Abstract
OBJECTIVE Evaluate the effect of aging using two different methods on the three-dimensional fit of zirconia abutments at the implant-abutment connection and estimate the probability of survival of anterior crowns supported by straight and 17-degree angled abutments. MATERIALS AND METHODS Two different zirconia abutment designs, straight and 17-degree angled abutments (n = 63/group), were evaluated in the current study. The abutments were randomly allocated into three experimental groups according to laboratory aging condition (134°C, 2.2 bar, 20 h): (i) control, (ii) autoclave aging, and (iii) hydrothermal reactor aging. Crystalline content was determined by X-Ray diffraction (XRD) and Raman spectroscopy, and microstructure was analyzed using field-emission gun scanning electron microscope (FEG-SEM). Implant-abutment volume misfit was determined in the straight abutments by micro-computed tomography using the silicone replica technique. For fatigue testing, abutments were torqued to the implants and connected to standardized maxillary incisor zirconia crowns. The assemblies were subjected to step-stress accelerated life testing (SSALT) in water until fracture or suspension. The use level probability Weibull curves and probability of survival for a mission of 50,000 cycles at 50, 100, 150 and 200 N were calculated and plotted. Fractured samples were analyzed using a stereomicroscope and scanning electron microscope. RESULTS The crystalline spectra depicted a zirconia system primarily composed of the tetragonal phase. Laboratory aging yielded a 20%- and 37%-increase in the monoclinic content for abutments aged in autoclave and hydrothermal reactor relative to control, respectively. A fully crystalline matrix with a regular grain size was observed in the FEG-SEM for control abutments, with a considerable presence of intergranular defects. While autoclave aging triggered no significant alteration to the microstructure, defect population was reduced after hydrothermal reactor aging. Control abutments presented a significantly higher volume misfit (2.128 ± 0.54 mm3) relative to aged abutments using autoclave (1.244 ± 0.48 mm3) or hydrothermal reactor (1.441 ± 0.41 mm3). The beta (β) values indicated that failures were predominantly controlled by material strength rather than fatigue damage accumulation for all groups, except for straight control abutments. Irrespective of aging, the probability of survival of straight and angled zirconia abutments was up to 95% (95-100%) at 50 and 100 N. A 50N-increase in the load resulted in wider range of survival estimate, with straight autoclave abutments percentage significantly lower probability of survival (77%) than angled hydrothermal reactor abutments (99%). At 200N, angled hydrothermal reactor (97%) or autoclave (82%) aged abutments demonstrated the highest probability of survival, angled control (71%) and straight hydrothermal reactor (69%) abutments intermediate values, and straight autoclave (23%) and control (7%) abutments the lowest estimate. The failure mode predominantly involved abutment and/or abutment screw fracture for both straight and angled abutments. CONCLUSIONS Hydrothermal aging significantly influenced volume misfit, as well as the probability of survival of zirconia abutments at higher loads for both angled and straight abutments.
Collapse
Affiliation(s)
- Edmara T P Bergamo
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of Sao Paulo, 9-75 Octavio Pinheiro Brizolla, 17012-901, Bauru, SP, Brazil.
| | - Tiago M B Campos
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of Sao Paulo, 9-75 Octavio Pinheiro Brizolla, 17012-901, Bauru, SP, Brazil
| | - Adolfo C O Lopes
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of Sao Paulo, 9-75 Octavio Pinheiro Brizolla, 17012-901, Bauru, SP, Brazil
| | - Karina B Cardoso
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of Sao Paulo, 9-75 Octavio Pinheiro Brizolla, 17012-901, Bauru, SP, Brazil
| | - Marcus V R Gouvea
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of Sao Paulo, 9-75 Octavio Pinheiro Brizolla, 17012-901, Bauru, SP, Brazil
| | - Everardo N S de Araújo-Júnior
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of Sao Paulo, 9-75 Octavio Pinheiro Brizolla, 17012-901, Bauru, SP, Brazil
| | - Lukasz Witek
- Department of Biomaterials, New York University College of Dentistry, 433 1st Avenue, New York, NY, USA; Department of Biomedical Engineering, New York University Tandon School of Engineering, 6 MetroTech Center, Brooklyn, NY, USA
| | - Petra C Gierthmühlen
- Department of Prosthodontics, Medical Faculty and University Hospital Düsseldorf, Heinrich-Heine-University, Moorenstraße 5, 40225 Düsseldorf, Germany
| | - Paulo G Coelho
- Department of Biomaterials, New York University College of Dentistry, 433 1st Avenue, New York, NY, USA; Hansjörg Wyss Department of Plastic Surgery, NYU Langone Medical Center, 222 East 41st Street New York, NY, USA; Department of Mechanical Engineering, New York University Tandon School of Engineering, 6 MetroTech Center, Brooklyn, NY, USA
| | - Ernesto B Benalcázar Jalkh
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of Sao Paulo, 9-75 Octavio Pinheiro Brizolla, 17012-901, Bauru, SP, Brazil; Department of Biomaterials, New York University College of Dentistry, 433 1st Avenue, New York, NY, USA
| | - Abbas Zahoui
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of Sao Paulo, 9-75 Octavio Pinheiro Brizolla, 17012-901, Bauru, SP, Brazil
| | - Laura F de Carvalho
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of Sao Paulo, 9-75 Octavio Pinheiro Brizolla, 17012-901, Bauru, SP, Brazil
| | - Estevam A Bonfante
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of Sao Paulo, 9-75 Octavio Pinheiro Brizolla, 17012-901, Bauru, SP, Brazil
| |
Collapse
|
11
|
Shelar P, Abdolvand H, Butler S. On the behaviour of zirconia-based dental materials: A review. J Mech Behav Biomed Mater 2021; 124:104861. [PMID: 34600431 DOI: 10.1016/j.jmbbm.2021.104861] [Citation(s) in RCA: 10] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/10/2021] [Revised: 09/23/2021] [Accepted: 09/24/2021] [Indexed: 11/28/2022]
Abstract
Zirconia-based dental materials are extensively used in clinical practice due to their tooth-like appearance, biofunctionality, biocompatibility, and affordability. However, premature clinical failures of veneering porcelains raise a concern about their integrity. Extensive studies have been performed over a decade to resolve this issue, but it is challenging to reference all information effectively. A single source identifying the significance of potential parameters on material performance has not previously been available. An evidence-based meta-narrative review technique was used to review the characteristic parameters that can affect the overall behaviour of zirconia-based materials. Keywords were chosen to assess manuscripts based on scientific coherence with this paper's research objective. Online keyword searches were carried out on ScienceDirect, PubMed, and SAGE databases for relevant published manuscripts from year 1985-2020.261 out of 3170 identified manuscripts were included. A total of 10 parameters were identified and classified into the material, manufacturing, and geometric aspects. The effect of every parameter was reviewed on the performance of the material. A discrepancy in findings was observed and is attributed to the fact that there is no standard methodology. This review acts as a single source that summarizes various parameters' contribution to zirconia-based dental materials' performance. This review facilitates manufacturing improvements by accounting for every parameter's effect on overall performance.
Collapse
Affiliation(s)
- Prashant Shelar
- Department of Mechanical & Materials Engineering, Western University, London, Ontario, Canada
| | - Hamidreza Abdolvand
- Department of Mechanical & Materials Engineering, Western University, London, Ontario, Canada
| | - Sheila Butler
- Schulich School of Medicine & Dentistry, Western University, London, Ontario, Canada.
| |
Collapse
|
12
|
Nanoscale physico-mechanical properties of an aging resistant ZTA composite. J Mech Behav Biomed Mater 2021; 123:104690. [PMID: 34385065 DOI: 10.1016/j.jmbbm.2021.104690] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/14/2021] [Revised: 06/26/2021] [Accepted: 07/02/2021] [Indexed: 11/21/2022]
Abstract
OBJECTIVE To characterize the effects of aging on the nanomechanical properties and 3D surface topographical parameters of an experimental Zirconia Toughened Alumina (ZTA) composite compared to its respective individual counterpart materials. METHODS Disk-shaped specimens comprised of three material groups were processed: 1) ZTA 70/30 (70% alumina reinforced with 30% second-generation 3Y-TZP); 2) Zpex (Second-generation 3Y-TZP), and; 3) Al2O3 (High purity Alumina) (n = 10/material, 12 × 1 mm). After synthesis, ceramic powders were pressed, the green-body samples were sintered and polished. Nanoindentation testing was performed to record elastic modulus (E) and hardness (H). Interferometry was utilized to assess 3D surface roughness parameters (Sa, Sq), while X-ray diffraction (XRD) and scanning electron microscope (SEM) assessed the crystalline content and microstructure. All tests were performed before and after simulated aging (134°C, 2.2 bar, 20 h). Statistical analyses were performed using linear mixed-model and least square difference pos-hoc tests (α = 5%). RESULTS XRD spectra indicated increase of monoclinic peaks for Zpex (~18%) relative to ZTA 70/30 (~2.5%) after aging. Additionally, aging did not affect the surface roughness parameters of ZTA 70/30 and Al2O3, although a significant increase in Sa was recorded for Zpex following aging (~90 nm) (p < 0.001). Al2O3 yielded the highest H and E values (H:21 GPa, E: 254 GPa), followed by ZTA 70/30 (H: 13 GPa, E: 214 GPa) and Zpex (H:11 GPa, E: 167 GPa), all significantly different (p < 0.03). CONCLUSION ZTA 70/30 and Al2O3 presented high hydrothermal stability with respect to all evaluated variables, where artificial aging significantly increased the monoclinic content and surface roughness of Zpex.
Collapse
|
13
|
Influence of Preaging Temperature on the Indentation Strength of 3Y-TZP Aged in Ambient Atmosphere. MATERIALS 2021; 14:ma14112767. [PMID: 34071126 PMCID: PMC8197138 DOI: 10.3390/ma14112767] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 04/30/2021] [Revised: 05/18/2021] [Accepted: 05/21/2021] [Indexed: 11/23/2022]
Abstract
Yttria-stabilized zirconia (3Y-TZP) containing 0.25% Al2O3, which is resistant to low temperature degradation (LTD), was aged for 10 h at 130–220 °C in air. The aged specimens were subsequently indented at loads ranging from 9.8 to 490 N using a Vickers indenter. The influence of preaging temperature on the biaxial strength of the specimens was investigated to elucidate the relationship between the extent of LTD and the strength of zirconia restorations that underwent LTD. The indented strength of the specimens increased as the preaging temperature was increased higher than 160 °C, which was accompanied by extensive t-ZrO2 (t) to m-ZrO2 (m) and c-ZrO2 (c) to r-ZrO2 (r) phase transformations. The influence of preaging temperature on the indented strength was rationalized by the residual stresses raised by the t→m transformation and the reversal of tensile residual stress on the aged specimen surface due to the indentation. The results suggested that the longevity of restorations would not be deteriorated if the aged restorations retain compressive residual stress on the surface, which corresponds to the extent of t→m phase transformation less than 52% in ambient environment.
Collapse
|
14
|
Koenig V, Bekaert S, Dupont N, Vanheusden A, Le Goff S, Douillard T, Chevalier J, Djaker N, Lamy de la Chapelle M, Amiard F, Dardenne N, Wulfman C, Mainjot A. Intraoral low-temperature degradation of monolithic zirconia dental prostheses: Results of a prospective clinical study with ex vivo monitoring. Dent Mater 2021; 37:1134-1149. [PMID: 33858665 DOI: 10.1016/j.dental.2021.03.008] [Citation(s) in RCA: 8] [Impact Index Per Article: 2.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/07/2021] [Revised: 02/25/2021] [Accepted: 03/29/2021] [Indexed: 02/04/2023]
Abstract
OBJECTIVE To investigate the intraoral development and kinetics of low-temperature degradation (LTD) in second-generation 3 mol.% yttria-doped tetragonal zirconia polycrystal (3Y-TZP) monolithic prostheses, as well as the influence of masticatory mechanical stress and glaze layer on it. METHODS A total of 101 posterior tooth elements were included in a prospective clinical study, which included ex vivo LTD monitoring (at baseline, 6 months, 1 year, and 2 years) using Raman spectroscopy (n = 2640 monoclinic phase measurement points per evaluation time) and SEM. Four types of areas (1-2 mm2 surface, 6 on molars, and 4 on premolars) were analyzed on each element surface: occlusal, axial, glazed, or unglazed. Raman depth mapping and high-resolution SEM were performed on the selected samples. RESULTS LTD developed in 3Y-TZP monolithic restorations 6 months after intraoral placement and progressed with time. After two years, the tetragonal-to-monoclinic transformation was non-uniform, with the presence of localized clusters of transformed grains. In axial areas, the grain aspect was typical of the classical nucleation-growth process reported for LTD, which progresses from the surface to a depth of several tens of microns. However, in occlusal areas, tribological stress generated surface crushing and grain pull-out from the clusters, which induced an underestimation of the aging process when the evaluation was limited to monoclinic phase quantification. Glazing cannot be considered a protection against LTD. SIGNIFICANCE If LTD occurs in dental prostheses in the same way as in orthopedic prostheses, its clinical impact is unknown and needs to be further studied.
Collapse
Affiliation(s)
- V Koenig
- Dental Biomaterials Research Unit (d-BRU), University of Liège (ULiège), 45 Quai G. Kurth, Liège, 4020, Belgium; Department of Fixed Prosthodontics, Institute of Dentistry, University of Liège Hospital (CHU), 45 Quai G. Kurth, Liège, 4020, Belgium
| | - S Bekaert
- Dental Biomaterials Research Unit (d-BRU), University of Liège (ULiège), 45 Quai G. Kurth, Liège, 4020, Belgium; Department of Fixed Prosthodontics, Institute of Dentistry, University of Liège Hospital (CHU), 45 Quai G. Kurth, Liège, 4020, Belgium
| | - N Dupont
- Dental Biomaterials Research Unit (d-BRU), University of Liège (ULiège), 45 Quai G. Kurth, Liège, 4020, Belgium; Department of Fixed Prosthodontics, Institute of Dentistry, University of Liège Hospital (CHU), 45 Quai G. Kurth, Liège, 4020, Belgium
| | - A Vanheusden
- Dental Biomaterials Research Unit (d-BRU), University of Liège (ULiège), 45 Quai G. Kurth, Liège, 4020, Belgium; Department of Fixed Prosthodontics, Institute of Dentistry, University of Liège Hospital (CHU), 45 Quai G. Kurth, Liège, 4020, Belgium
| | - S Le Goff
- Unité de Recherches en Biomatériaux Innovants et Interfaces (URB2i) - EA4462, Faculté de Chirurgie Dentaire, Université Paris Descartes, Sorbonne Paris-Cité, Montrouge, 92120, France
| | - T Douillard
- Université de Lyon, INSA Lyon, CNRS, MATEIS, UMR 5510, F-69621 Villeurbanne, France
| | - J Chevalier
- Université de Lyon, INSA Lyon, CNRS, MATEIS, UMR 5510, F-69621 Villeurbanne, France
| | - N Djaker
- Université Sorbonne Paris Nord, CNRS, UMR 7244, CSPBAT, Laboratoire de Chimie, Structures et Propriétés de Biomatériaux et d'Agents Thérapeutiques, 93017 Bobigny, France
| | - M Lamy de la Chapelle
- Institut des Molécules et Matériaux du Mans (IMMM - UMR6283), Université du Mans, avenue Olivier Messiaen, 72085 Le Mans Cedex 9, France
| | - F Amiard
- Institut des Molécules et Matériaux du Mans (IMMM - UMR6283), Université du Mans, avenue Olivier Messiaen, 72085 Le Mans Cedex 9, France
| | - N Dardenne
- Department of Public Health, University of Liège, 4000 Liège, Belgium
| | - C Wulfman
- Dental Biomaterials Research Unit (d-BRU), University of Liège (ULiège), 45 Quai G. Kurth, Liège, 4020, Belgium; Unité de Recherches en Biomatériaux Innovants et Interfaces (URB2i) - EA4462, Faculté de Chirurgie Dentaire, Université Paris Descartes, Sorbonne Paris-Cité, Montrouge, 92120, France
| | - A Mainjot
- Dental Biomaterials Research Unit (d-BRU), University of Liège (ULiège), 45 Quai G. Kurth, Liège, 4020, Belgium; Department of Fixed Prosthodontics, Institute of Dentistry, University of Liège Hospital (CHU), 45 Quai G. Kurth, Liège, 4020, Belgium.
| |
Collapse
|
15
|
Flask JD, Thompson GA, Singh M, Berzins DW. Edge chipping of translucent zirconia. J Prosthet Dent 2021; 127:793-800. [PMID: 33581865 DOI: 10.1016/j.prosdent.2020.12.009] [Citation(s) in RCA: 6] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/07/2020] [Revised: 12/09/2020] [Accepted: 12/09/2020] [Indexed: 11/28/2022]
Abstract
STATEMENT OF PROBLEM More translucent dental zirconias have been developed by incorporating the cubic phase and reducing the tetragonal phase content that undergoes transformation toughening, leading to reduced mechanical properties. Whether the clinically relevant mechanical property of the edge chipping toughness of the material is also reduced is unclear. PURPOSE The purpose of this in vitro study was to evaluate the edge chipping toughness and translucency of translucent zirconia, 3mol% yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP), and lithium disilicate. MATERIAL AND METHODS Two translucent zirconia products, Katana and Lava Esthetic; one 3Y-TZP, Lava Plus; and one lithium disilicate, IPS e.max Press were prepared and tested for phase composition via X-ray diffraction (XRD) (n=3), translucency via a spectrophotometer (n=20), and edge chipping via a universal testing machine with a custom-machined specimen holder and diamond indenter (n=20). The 3Y-TZP and lithium disilicate served as the optimal control materials for edge chipping and translucency, respectively. Translucency was compared with 1-way ANOVA and edge toughness with ANCOVA (α=.05). RESULTS The XRD showed the 3Y-TZP to be almost completely tetragonal phase compared with the 2 translucent zirconia products that were predominantly cubic. Katana UTML and IPS e.max Press had a statistically similar (P>.05) translucency that was significantly (P<.05) greater than that of Lava Esthetic and Lava Plus. The edge toughness of Katana UTML was 304 N/mm, IPS e.max Press was 354 N/mm, Lava Esthetic was 394 N/mm, and Lava Plus was 717 N/mm, with significance rankings of Katana UTM<IPS e.max Press=Lava Esthetic<Lava Plus. CONCLUSIONS Some translucent zirconias had translucency similar to that of lithium disilicate; however, as translucency increased with increased cubic content, edge toughness decreased.
Collapse
Affiliation(s)
- Joseph D Flask
- Graduate student of Dental Biomaterials, Department of General Dental Sciences, Marquette University School of Dentistry, Milwaukee, Wis.
| | - Geoffrey A Thompson
- Professor, Graduate Prosthodontics, Department of General Dental Sciences, Marquette University School of Dentistry, Milwaukee, Wis
| | - Maharaj Singh
- Research Assistant Professor, Biostatistics-Research and Graduate Studies, Marquette University School of Dentistry, Milwaukee, Wis
| | - David W Berzins
- Professor, Dental Biomaterials, Department of General Dental Sciences, Marquette University School of Dentistry, Milwaukee, Wis
| |
Collapse
|
16
|
Bhaduri SB, Sikder P. Biomaterials for Dental Applications. Biomed Mater 2021. [DOI: 10.1007/978-3-030-49206-9_14] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/22/2022]
|
17
|
Cotič J, Kocjan A, Panchevska S, Kosmač T, Jevnikar P. In vivo ageing of zirconia dental ceramics - Part II: Highly-translucent and rapid-sintered 3Y-TZP. Dent Mater 2020; 37:454-463. [PMID: 33376028 DOI: 10.1016/j.dental.2020.11.019] [Citation(s) in RCA: 6] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/28/2020] [Revised: 11/27/2020] [Accepted: 11/27/2020] [Indexed: 10/22/2022]
Abstract
OBJECTIVE 3Y-TZP ceramics with reduced alumina content have improved translucency and are used in monolithic dental restorations without porcelain-based veneers. The workflow can be further streamlined with rapid sintering. This study was designed to assess how these approaches affect ageing when the materials are exposed to the oral environment in vivo. METHODS 43 discs were fabricated from 3Y-TZP powder with 0.05% Al2O3 and sintered with conventional or rapid regimens (1450 °C 2 h, 1530 °C 2 h, or 1530 °C 25 min). Their surfaces were polished or airborne-particle abraded with 50 μm Al2O3. The discs were incorporated in complete dentures of 16 volunteers and worn continuously for up to 48 months. Ageing changes on disc surfaces were monitored every 6 months by X-ray diffraction, scanning electron microscopy and atomic force microscopy. Data was statistically analysed with linear models. RESULTS The amount of monoclinic phase on polished surfaces increased linearly, reaching up to 40% after 48 months in vivo. The ageing process observed for rapid sintering was 1.6 times faster compared to conventional sintering. A nano-scale increase in roughness with microcracking was also detected on polished surfaces. Airborne-particle abraded surfaces did not exhibit clear signs of ageing during the course of the study. SIGNIFICANCE Highly-translucent 3Y-TZP ceramics are more susceptible to ageing than classic 3Y-TZP. After 4 years in vivo, the extent of degradation did not yet constitute grounds for clinical concern, but was more pronounced in materials prepared with rapid sintering.
Collapse
Affiliation(s)
- Jasna Cotič
- Department of Prosthodontics, Faculty of Medicine, University of Ljubljana, Hrvatski Trg 6, SI-1000 Ljubljana, Slovenia
| | - Andraž Kocjan
- Department for Nanostructured Materials, Jožef Stefan Institute, Jamova 39, SI-1000 Ljubljana, Slovenia
| | - Sanja Panchevska
- Faculty of Dentistry, Ss. Cyril and Methodius University, Majka Tereza 43, MK-1000 Skopje, Republic of North Macedonia
| | - Tomaž Kosmač
- Jožef Stefan Institute, Jamova 39, SI-1000 Ljubljana, Slovenia
| | - Peter Jevnikar
- Department of Prosthodontics, Faculty of Medicine, University of Ljubljana, Hrvatski Trg 6, SI-1000 Ljubljana, Slovenia.
| |
Collapse
|
18
|
Kocjan A, Cotič J, Kosmač T, Jevnikar P. In vivo aging of zirconia dental ceramics - Part I: Biomedical grade 3Y-TZP. Dent Mater 2020; 37:443-453. [PMID: 33334584 DOI: 10.1016/j.dental.2020.11.023] [Citation(s) in RCA: 13] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/28/2020] [Revised: 11/27/2020] [Accepted: 11/27/2020] [Indexed: 02/04/2023]
Abstract
OBJECTIVE In vivo aging of biomedical grade 3Y-TZP ceramics in the oral environment was assessed and compared to artificially accelerated in vitro hydrothermal aging extrapolations at 37°C. METHODS 88 discs were pressed and sintered (1450-1500°C) from two commercial 3Y-TZP compositions containing 0.25% Al2O3 to generate finer- and coarser-grained specimens. As-sintered (AS) and airborne-particle abraded (APA; 50μm Al2O3) surfaces were investigated. In vivo aging was performed by incorporating specimens in lingual flanges of complete dentures of 12 edentulous volunteers who wore them continuously for up to 24 months. For comparison, in vitro hydrothermal aging at 134°C was also performed and analysed by XRD and (FIB)-SEM. Data was statistically analysed with linear regression models. RESULTS Finer and coarser-grained specimens exhibited statistically insignificant differences in aging in vivo. The monoclinic fraction (Xm) on AS surfaces abruptly increased to ∼8% after 6 months. The aging process then proceeded with slower linear kinetics (∼0.24%/month). After 24 months, Xm reached ∼12%. The calculated maximum transformed layer was 0.385μm representing one layer of transformed grains. APA surfaces were highly aging resistant. The initial Xm of ∼4.0% linearly increased by 0.03%/month in vivo. In vitro aging exhibited an initial induction period, followed by linear aging kinetics. Coarser-grained AS surfaces aged significantly faster than fine-grained (2.41%/h compared to 2.16%/h). APA discs aged at a rate of 0.3%/h in vitro. Microcracking within a single grain and pull-out of grain clusters were observed on aged AS surfaces. SIGNIFICANCE Biomedical grade 3Y-TZP was susceptible to in vivo aging. After 2 years in vivo, the aging kinetics were almost 3-times faster than the generally accepted in vitro-in vivo extrapolation.
Collapse
Affiliation(s)
- Andraž Kocjan
- Department for Nanostructured Materials, Jožef Stefan Institute, Jamova 39, SI-1000 Ljubljana, Slovenia
| | - Jasna Cotič
- Department of Prosthodontics, Faculty of Medicine, University of Ljubljana, Hrvatski trg 6, SI-1000 Ljubljana, Slovenia
| | - Tomaž Kosmač
- Jožef Stefan Institute, Jamova 39, SI-1000 Ljubljana, Slovenia
| | - Peter Jevnikar
- Department of Prosthodontics, Faculty of Medicine, University of Ljubljana, Hrvatski trg 6, SI-1000 Ljubljana, Slovenia.
| |
Collapse
|
19
|
Bergamo ETP, Cardoso KB, Lino LFO, Campos TMB, Monteiro KN, Cesar PF, Genova LA, Thim GP, Coelho PG, Bonfante EA. Alumina-toughened zirconia for dental applications: Physicochemical, mechanical, optical, and residual stress characterization after artificial aging. J Biomed Mater Res B Appl Biomater 2020; 109:1135-1144. [PMID: 33314536 DOI: 10.1002/jbm.b.34776] [Citation(s) in RCA: 6] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/04/2020] [Revised: 11/23/2020] [Accepted: 11/28/2020] [Indexed: 01/01/2023]
Abstract
To characterize the physicomechanical properties of an alumina-toughened zirconia (ATZ). ATZ synthesis consisted of the addition of alumina particles in an yttria-stabilized tetragonal zirconia polycrystals (3Y-TZP) matrix. Specimens were obtained by uniaxial and isostatic pressing ATZ and 3Y-TZP powders and sintering at 1600°C/1 h and 1550°C/1 h, respectively. Crystalline content and residual stress were evaluated using X-ray diffraction (XRD). Microstructure was characterized by scanning electron microscopy (SEM). Optical properties were determined by reflectance test. Mechanical properties were assessed by biaxial flexural strength test. All analyses were performed before and after aging (134°C, 20 h, 2 bar). XRD and SEM revealed a typical ATZ and 3Y-TZP crystalline content, chiefly tetragonal phase, with a dense polycrystalline matrix, though a smaller grain size for ATZ. Aging triggered a similar monoclinic transformation for both systems; however, ATZ exhibited higher residual compressive stresses than 3Y-TZP. While as-processed 3Y-TZP demonstrated significantly higher characteristic strength relative to ATZ, no significant difference was observed after aging (~215 MPa increase in the ATZ strength). ATZ presented significantly higher opacity relative to 3Y-TZP, although aging significantly increased the translucency of both systems (increase difference significantly higher in the 3Y-TZP compared to ATZ). ATZ physicomechanical properties support its applicability in the dental field, with a lower detrimental effect of aging relative to 3Y-TZP.
Collapse
Affiliation(s)
- Edmara T P Bergamo
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of São Paulo, Bauru, SP, Brazil
| | - Karina B Cardoso
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of São Paulo, Bauru, SP, Brazil
| | - Lucas F O Lino
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of São Paulo, Bauru, SP, Brazil
| | - Tiago M B Campos
- Department of Physics, Aeronautics Technological Institute, São José dos Campos, SP, Brazil
| | - Kelli N Monteiro
- Department of Biomaterials and Oral Biology, University of São Paulo, School of Dentistry, São Paulo, SP, Brazil
| | - Paulo F Cesar
- Department of Biomaterials and Oral Biology, University of São Paulo, School of Dentistry, São Paulo, SP, Brazil
| | - Luis A Genova
- Center of Materials Science and Technology, Institute of Research in Nuclear Energy, São Paulo, SP, Brazil
| | - Gilmar P Thim
- Department of Physics, Aeronautics Technological Institute, São José dos Campos, SP, Brazil
| | - Paulo G Coelho
- Department of Biomaterials and Biomimetics, Hansjörg Wyss Department of Plastic Surgery, Mechanical and Aerospace Engineering, New York University, New York City, NY, USA
| | - Estevam A Bonfante
- Department of Prosthodontics and Periodontology, Bauru School of Dentistry - University of São Paulo, Bauru, SP, Brazil
| |
Collapse
|
20
|
de Araújo-Júnior ENS, Bergamo ETP, Campos TMB, Benalcázar Jalkh EB, Lopes ACO, Monteiro KN, Cesar PF, Tognolo FC, Tanaka R, Bonfante EA. Hydrothermal degradation methods affect the properties and phase transformation depth of translucent zirconia. J Mech Behav Biomed Mater 2020; 112:104021. [PMID: 32882676 DOI: 10.1016/j.jmbbm.2020.104021] [Citation(s) in RCA: 12] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/31/2020] [Revised: 07/28/2020] [Accepted: 07/31/2020] [Indexed: 02/04/2023]
Abstract
OBJECTIVES To characterize the optical and mechanical properties of a commercial and in-house translucent Y-TZP before and after aging in autoclave or hydrothermal reactor. METHODS In-house experimental discs were obtained through uniaxial and isostatic pressing a translucent Y-TZP powder and sintering at 1,550 °C/1 h. Commercial discs were milled from pre-sintered blocks fabricated with the same powder through uniaxial and isostatic pressing and sintering. Discs were allocated into three groups according to aging condition: immediate, aged via autoclave, or reactor (134 °C, 20 h, 2.2 bar). Crystalline content and microstructure were evaluated using X-ray diffraction (XRD) and scanning electron microscopy (SEM). Residual compressive stress (CS) was determined by Raman spectroscopy. Optical properties were determined by the contrast ratio (CR) and translucency parameter (TP) using reflectance data. Mechanical properties were assessed by Vickers hardness, fracture toughness and biaxial flexural strength tests. RESULTS XRD and SEM revealed a typical Y-TZP crystalline content, chiefly tetragonal phase, and a dense crystalline matrix for both processing protocols. Reactor aging triggered a more pronounced t-m transformation relative to autoclave. In-house and commercial Y-TZPs demonstrated similar CR and TP, with reactor aging significantly increasing their translucency. Similarly, reactor aging influenced Vickers hardness and fracture toughness. In-house processed Y-TZP clearly demonstrated the presence of CS, whereas commercial Y-TZP showed no presence of CS. Non-aged in-house Y-TZP resulted in significantly lower characteristic strength relative to commercial Y-TZP. While aging protocols significantly increased the characteristic strength of in-house Y-TZP, reactor significantly decreased commercial Y-TZP characteristic strength. Both Y-TZP processing protocols demonstrated high reliability at high-stress missions, with no detrimental effect of aging. CONCLUSIONS Laboratory aging methodology significantly influenced optical and mechanical properties of a commercial and in-house translucent Y-TZP.
Collapse
Affiliation(s)
- Everardo N S de Araújo-Júnior
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil.
| | - Edmara T P Bergamo
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Tiago M B Campos
- Department of Physics, Technological Institute of Aeronautics, São José Dos Campos, SP, Brazil
| | - Ernesto B Benalcázar Jalkh
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Adolfo C O Lopes
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Kelli N Monteiro
- Department of Biomaterials and Oral Biology, University of São Paulo, School of Dentistry, São Paulo, SP, Brazil
| | - Paulo F Cesar
- Department of Biomaterials and Oral Biology, University of São Paulo, School of Dentistry, São Paulo, SP, Brazil
| | - Fernanda C Tognolo
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| | - Ricardo Tanaka
- TNK Lab, Rua João de Santa Maria, 129 - Jardim da Saúde - São Paulo, SP, Brazil
| | - Estevam A Bonfante
- Department of Prosthodontics and Periodontology, University of São Paulo, Bauru School of Dentistry, Bauru, SP, Brazil
| |
Collapse
|
21
|
Yang H, Xu YL, Hong G, Yu H. Effects of low-temperature degradation on the surface roughness of yttria-stabilized tetragonal zirconia polycrystal ceramics: A systematic review and meta-analysis. J Prosthet Dent 2020; 125:222-230. [PMID: 32115216 DOI: 10.1016/j.prosdent.2020.01.005] [Citation(s) in RCA: 15] [Impact Index Per Article: 3.8] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/08/2019] [Revised: 01/16/2020] [Accepted: 01/16/2020] [Indexed: 11/15/2022]
Abstract
STATEMENT OF PROBLEM A wide range of yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) ceramics have been applied for dental restorations. However, whether hydrothermal aging affects the surface roughness of Y-TZP is unknown. PURPOSE The purpose of this systematic review and meta-analysis was to evaluate the effects of low-temperature degradation (LTD) on the surface roughness of Y-TZP ceramics. MATERIAL AND METHODS This report follows the Preferred Reporting Items for Systematic Reviews and Qualitative Analyses statement. The literature search was conducted with Medline through the PubMed, Web of Science, and Cochrane Library with no publication year limits. The screening and quality assessment were performed by 2 independent reviewers. The studies comparing the surface roughness of Y-TZP ceramics after LTD by using steam autoclave aging were included in the meta-analysis. Meta-analyses were conducted with a random-effects model (α=.05) by using Review Manager Software (Cochrane Collaboration). RESULTS Of the 203 potentially relevant studies, 32 full texts were assessed for eligibility. A total of 17 articles were included in the systematic review, and 15 were included in the qualitative analyses. The results showed no significant difference in the arithmetic average height (Ra) values between the nonaged and aged Y-TZP (P=.670; mean difference=0.01; 95% confidence interval=-0.03 to 0.05). Subgroup analyses revealed that the aging duration (P=.003) and specimen preparation (P=.010) contributed significantly to the changes in the surface roughness of the Y-TZP ceramics. CONCLUSIONS Although LTD was found to have no significant effects on the surface roughness of Y-TZP ceramics, the effects of LTD depended on the duration of the steam autoclave process and the specimen preparation.
Collapse
Affiliation(s)
- Hui Yang
- Postgraduate student, Fujian Key Laboratory of Oral Diseases & Fujian Provincial Engineering Research Center of Oral Biomaterial & Stomatological Key Laboratory of Fujian College and University, School and Hospital of Stomatology, Fujian Medical University, Fuzhou, PR China
| | - Yi-Li Xu
- Postgraduate student, Fujian Key Laboratory of Oral Diseases & Fujian Provincial Engineering Research Center of Oral Biomaterial & Stomatological Key Laboratory of Fujian College and University, School and Hospital of Stomatology, Fujian Medical University, Fuzhou, PR China
| | - Guang Hong
- Professor, Division for Globalization Initiative, Liaison Center for Innovative Dentistry, Tohoku University Graduate School of Dentistry, Sendai, Japan
| | - Hao Yu
- Associate Professor, Fujian Key Laboratory of Oral Diseases & Fujian Provincial Engineering Research Center of Oral Biomaterial & Stomatological Key Lab of Fujian College and University, School and Hospital of Stomatology, Fujian Medical University, Fuzhou, PR China; Adjunct Associate Professor, Department of Applied Prosthodontics, Graduate School of Biomedical Sciences, Nagasaki University, Nagasaki, Japan.
| |
Collapse
|
22
|
Fu L, Engqvist H, Xia W. Glass-Ceramics in Dentistry: A Review. MATERIALS 2020; 13:ma13051049. [PMID: 32110874 PMCID: PMC7084775 DOI: 10.3390/ma13051049] [Citation(s) in RCA: 74] [Impact Index Per Article: 18.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 11/18/2019] [Revised: 01/21/2020] [Accepted: 01/22/2020] [Indexed: 01/18/2023]
Abstract
In this review, we first briefly introduce the general knowledge of glass–ceramics, including the discovery and development, the application, the microstructure, and the manufacturing of glass–ceramics. Second, the review presents a detailed description of glass–ceramics in dentistry. In this part, the history, property requirements, and manufacturing techniques of dental glass–ceramics are reviewed. The review provided a brief description of the most prevalent clinically used examples of dental glass–ceramics, namely, mica, leucite, and lithium disilicate glass–ceramics. In addition, we also introduce the newly developed ZrO2–SiO2 nanocrystalline glass–ceramics that show great potential as a new generation of dental glass–ceramics. Traditional strengthening mechanisms of glass–ceramics, including interlocking, ZrO2–reinforced, and thermal residual stress effects, are discussed. Finally, a perspective and outlook for future directions in developing new dental glass–ceramics is provided to offer inspiration to the dental materials community.
Collapse
Affiliation(s)
- Le Fu
- School of Materials Science and Engineering, Central South University, Changsha 410083, China
- Correspondence: (L.F.); (W.X.)
| | - Håkan Engqvist
- Applied Materials Science, Department of Engineering Science, Uppsala University, 751 21 Uppsala, Sweden;
| | - Wei Xia
- Applied Materials Science, Department of Engineering Science, Uppsala University, 751 21 Uppsala, Sweden;
- Correspondence: (L.F.); (W.X.)
| |
Collapse
|
23
|
Vila-Nova TEL, Gurgel de Carvalho IH, Moura DMD, Batista AUD, Zhang Y, Paskocimas CA, Bottino MA, de Assunção E Souza RO. Effect of finishing/polishing techniques and low temperature degradation on the surface topography, phase transformation and flexural strength of ultra-translucent ZrO 2 ceramic. Dent Mater 2020; 36:e126-e139. [PMID: 32008750 DOI: 10.1016/j.dental.2020.01.004] [Citation(s) in RCA: 21] [Impact Index Per Article: 5.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/13/2019] [Revised: 11/24/2019] [Accepted: 01/14/2020] [Indexed: 01/25/2023]
Abstract
OBJECTIVE To investigate the effect of different surface finishing and polishing regimes and low temperature degradation on flexural strength, phase transformation and surface topography of ultra-translucent ZrO2 ceramic. METHODS 300 (n=15/group) of conventional zirconia (Z: Ice Zirkon Transluzent) and ultra-translucent zirconia (UT: Prettau Anterior) bar-specimens were made and divided according to the "Finishing/Polishing" - (C - Control, B - diamond rubber polishers, P - adjusting with burs, PB - adjusting with burs+diamond polishers, PG - adjusting with burs+glaze), "Low temperature Degradation (LTD)" (with or without a treatment at 127°C, 1.7bar/24h). Then, a 3-point mini flexural test was performed in a universal testing machine (1mm/min, 500kgf load cell). SEM, EDS, XDR, AFM, optical profilometry and Weibull analysis were performed. Data were analyzed by 3-way ANOVA and Tukey's post-test (5%). RESULTS Groups ZPBD (1670±253MPa), ZBD (1664±217MPa), and ZB (1655±3678MPa) showed significantly higher flexural strength than the UTPG group (372±56MPa). The Weibull modulus was significantly higher for the ZPD group compared to the UB, UCD, UPD and UPBD, while UTB, UTCD and UTPD had the lowest value. Monoclinic phases were observed only in the conventional zirconia groups and were more evident after LTD. Diamond rubber polishers presented less roughness for both zirconias. SIGNIFICANCE The use of diamond rubber polishers is the most suitable finishing/polishing method for zirconia ceramic restorations and that final glazing reduces the fracture resistance of these materials.
Collapse
Affiliation(s)
- Taciana Emília Leite Vila-Nova
- Federal University of Rio Grande do Norte (UFRN), Department of Dentistry, Av. Salgado Filho, 1787, Lagoa Nova, Natal, RN, CEP: 59056-000, Brazil.
| | - Isabelle Helena Gurgel de Carvalho
- Federal University of Rio Grande do Norte (UFRN), Department of Dentistry, Division of Prosthodontics, Av. Salgado Filho, 1787, Lagoa Nova, Natal, RN, 59056-000, Brazil.
| | - Dayanne Monielle Duarte Moura
- Federal University of Rio Grande do Norte (UFRN), Department of Dentistry, Division of Prosthodontics, Av. Salgado Filho, 1787, Lagoa Nova, Natal, RN, 59056-000, Brazil.
| | - André Ulisses Dantas Batista
- Federal University of Paraíba (UFPB), Department of Restorative Dentistry, Conj. Pres. Castelo Branco III, João Pessoa, PB, 58033-455, Brazil.
| | - Yu Zhang
- New York University College of Dentistry, Department of Biomaterials and Biomimetics, 433 First Avenue, Room 810, New York, NY, 10010, United States.
| | - Carlos Alberto Paskocimas
- Federal University of Rio Grande do Norte (UFRN), Department of Material Engineering, Av. Salgado Filho, 3000, Lagoa Nova, Natal, RN, Brazil.
| | - Marco Antonio Bottino
- São Paulo State University (UNESP), Institute of Science and Technology, Av Engenheiro Francisco José Longo, 777, Jardim São Dimas, São José dos Campos, São Paulo, São José dos Campos, CEP: 12245-000, Brazil.
| | - Rodrigo Othávio de Assunção E Souza
- Adjunct Professor at Federal University of Rio Grande do Norte (UFRN), Department of Dentistry, Division of Prosthodontics, Av. Salgado Filho, 1787, Lagoa Nova, Natal, RN, 59056-000, Brazil.
| |
Collapse
|
24
|
Maroun EV, Guimarães JGA, de Miranda WG, Netto LRC, Elias AB, da Silva EM. Bond Strength Stability of Self-adhesive Resin Cement to Etched Vitrified Yttria-stabilized Tetragonal Zirconia Polycrystal Ceramic After Thermomechanical Cycling. Oper Dent 2019; 44:545-555. [DOI: 10.2341/18-131-l] [Citation(s) in RCA: 6] [Impact Index Per Article: 1.2] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/23/2022]
Abstract
SUMMARY
The purpose of this study was to evaluate the influence of thermomechanical cycling on the bond strength stability of self-adhesive resin cement to vitrified yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) ceramic. Y-TZP ceramic blocks were divided into four groups according to the surface treatments: AS, as sintered; SB, sandblasted with 50-μm Al2O3 particles; LG, vitrification with a low-fusing glaze and etching with 10% hydrofluoric acid; and HC, vitrification with a ceramic liner and etching with 10% hydrofluoric acid. Lithium disilicate ceramic blocks etched with 10% hydrofluoric acid for 20 seconds (EM) were also tested. Blocks of resin composite were cemented on the ceramic block surfaces using a self-adhesive resin cement. Half of the blocks from each group were cut into beams and submitted to microtensile bond strength (μTBS) testing after immersion in water at 37°C for 24 hours and the other half after mechanical (1,200,000 cycles, 98 N, 2.5 Hz) and thermal (10,000 cycles, 5-55°C, 30-second dwell time) cycling (TMC). Data were analyzed using one-way analysis of variance, Tukey's honest significant difference post hoc test, and Student t-test (α=0.05). After 24 hours, EM and LG presented similar and the highest μTBS, whereas AS showed the lowest μTBS (p<0.05). After TMC, EM presented the highest μTBS, followed by LG (p<0.05). Only EM and LG maintained the stability of μTBS after TMC (p>0.05). The bonding to Y-TZP ceramic vitrified with a low-fusing glaze withstood thermomechanical cycling.
Collapse
Affiliation(s)
- EV Maroun
- Eduardo Victor Maroun, DDS, MSC, associate researcher, Analytical Laboratory of Restorative Biomaterials–LABiom-R, School of Dentistry, Universidade Federal Fluminense, Niterói, Rio de Janeiro, Brazil
| | - JGA Guimarães
- José Guilherme Antunes Guimarães, DDS, MSc, PhD, associate professor, Analytical Laboratory of Restorative Biomaterials - LABiom-R, School of Dentistry, Universidade Federal Fluminense, Niterói, Rio de Janeiro, Brazil
| | - WG de Miranda
- Walter Gomes de Miranda Júnior, DDS, MSc, PhD, associate professor, Department of Biomaterials and Oral Biology, School of Dentistry, University of São Paulo, São Paulo, Brazil
| | - LRC Netto
- Luciano Ribeiro Corrêa Netto, DDS, MSc, postgraduate student, Analytical Laboratory of Restorative Biomaterials - LABiom-R, School of Dentistry, Universidade Federal Fluminense, Niterói, Rio de Janeiro, Brazil
| | - AB Elias
- Alexandre Barbosa Elias, DDS, MSc, PhD, adjunct professor, Analytical Laboratory of Restorative Biomaterials - LABiom-R, School of Dentistry, Universidade Federal Fluminense, Niterói, Rio de Janeiro, Brazil
| | - EM da Silva
- Eduardo Moreira da Silva, DDS, MSc, PhD, full professor, Analytical Laboratory of Restorative Biomaterials - LABiom-R, School of Dentistry, Universidade Federal Fluminense, Niterói, Rio de Janeiro, Brazil
| |
Collapse
|