Comparison of hardness and polishability of various occlusal splint materials

Influence of different print orientations on properties and behavior of additively manufactured resin dental devices: A systematic review and meta-analysis

STATEMENT OF PROBLEM

Different factors affect 3-dimensionally (3D) printed resin products. However, evidence on the effect of the print orientation on resin dental devices is lacking.

PURPOSE

The purpose of this systematic review and meta-analysis was to assess the impact of print orientation on the properties and accuracy of 3D printed implant surgical guides, occlusal devices, clear orthodontic retainers, and aligners.

MATERIAL AND METHODS

The electronic databases PubMed (MEDLINE), Cochrane, and Scopus were comprehensively searched in July 2024. A modified Consolidated Standards of Reporting Trials (CONSORT) statement was used to judge the included studies, and the data were analyzed by the RevMan 5.4 software program of the Cochrane collaboration by applying an inverse variance analysis (α=.05).

RESULTS

Twenty-six records were included. Complete arch, solid surgical guides with horizontal printing orientation exhibited the highest accuracy (P≤.01). Short-span surgical guides printed vertically showed relatively high accuracy (P≤.05). Hollow or mesh devices might not be affected by orientations. Occlusal device accuracy favored horizontal orientation, but correlated with the technology and materials, while the accuracy of orthodontic aligners revealed controversial findings, assuming the limited impact of orientation on orthodontic aligners. The cytotoxicity of occlusal devices was a material-related biological characteristic and unaffected by orientation. Although flexural strength favors horizontal orientation, conflicting results were observed for physical and other mechanical properties due to several variables.

CONCLUSIONS

Horizontal orientation is recommended for printing complete arch surgical guides, while the accuracy of short surgical guides might favor vertical orientation. The physical mechanical properties depend on the printing orientation, technology, material, and printed parts, but horizontal orientation might produce parts with the best mechanical performance.

Mechanical performance of 3-dimensionally printed resins compared with conventional and milled resins for the manufacture of occlusal devices: A systematic review

STATEMENT OF PROBLEM

Digital methods for manufacturing occlusal devices provide advantages over conventional techniques, but information about the mechanical properties of 3-dimensionally (3D) printed resins is scarce.

PURPOSE

The purpose of this systematic review was to evaluate the literature to determine whether 3D-printed resins for occlusal devices present satisfactory mechanical performance when compared with milled and conventional heat polymerized and autopolymerized resins.

MATERIAL AND METHODS

This systematic review followed the guidelines of the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) protocol and was registered in the Open Science Framework. The search strategy was applied without restriction of time and language to Embase, PubMed, Scopus, Science Direct, and Web of Science databases, and to the nonpeer-reviewed literature in ProQuest and Google Scholar. The selection process was conducted independently in 2 stages by 2 reviewers according to the eligibility criteria. The risk of bias was analyzed by using a checklist of important parameters to be considered. The systematic review considered the population, intervention, comparison, outcome, studies (PICOS) format, where population was resins for 3D printing of occlusal devices, intervention was inherent characteristics of the resin, comparison was conventional heat polymerized, autopolymerized, and milled resins, outcome was mechanical performance, and studies were in vitro experimental studies.

RESULTS

A total of 1430 articles were found with the search strategy. After removing 182 duplicates found in Rayyan, the title and abstract of 1248 articles were evaluated, of which 37 articles were screened from the databases, 23 were selected for full reading, and 6 met the eligibility criteria and were included in this review; 1 had a low risk of bias and 5 had a moderate risk. An additional search of the reference list of included articles did not result in the inclusion of any articles. A quantitative meta-analysis could not be performed because of the heterogeneity of the included studies regarding the type of resin used and the method for evaluating mechanical performance.

CONCLUSIONS

Resins for 3D printing had satisfactory mechanical performance for interocclusal devices when compared with conventional heat polymerized and autopolymerized resins, except for hardness. Milled resins were better than 3D-printed resins in hardness, wear resistance, flexural strength, flexural modulus, and fracture resistance when printing angle and thickness were not considered. Further development is needed in terms of printing techniques and chemical composition, as they are important for optimal mechanical properties and clinical performance.

Comparative analysis of polishing protocols on microhardness and surface roughness of occlusal device materials fabricated using microwave-polymerized acrylic or 3D printed resins

STATEMENT OF PROBLEM

With advancements in digital technologies, the digital workflow has revolutionized the fabrication of occlusal devices through additive methods using 3-dimensional (3D) printing. However, an established protocol for polishing 3D printed occlusal devices is lacking, despite this step being crucial for minimizing surface porosity, material fatigue and preventing bacterial plaque accumulation, thereby contributing to device longevity.

PURPOSE

The purpose of this in vitro study was to evaluate the impact of polishing systems on the surface roughness and Vickers microhardness of heat-polymerizing acrylic resin and 3D printing resins used for occlusal devices.

MATERIAL AND METHODS

One hundred and twenty microwaved-polymerized acrylic resin and 3D printed resin specimens (40×40×3 mm) were divided into 12 groups (n=10) based on the type of resin and polishing protocol (Sealant, DhPro, Dhpro + Sealant, Trihawk, Trihawk + Sealant, and control). Surface roughness (Ra) and Vickers microhardness were tested. Additionally, 1 specimen per group underwent scanning electron microscopy before and after thermocycling (5000 cycles, 5 ºC and 55 ºC). Data analysis involved a 2-way ANOVA, 2-way repeated measured ANOVA, and Tukey's multiple comparison test (α=.05).

RESULTS

The Trihawk polishing protocol yielded significantly higher microhardness and lower surface roughness values for both resins. After thermocycling, the acrylic resin maintained its surface roughness for the Trihawk, Trihawk + Sealant, and unpolished groups, but all groups showed decreased microhardness. The 3D printing resin exhibited increased surface roughness and reduced microhardness after thermocycling across all groups.

CONCLUSIONS

The polishing protocol affects the surface microhardness and roughness of 3D printing resins and microwave acrylic resins for occlusal devices. Polishing using the Trihawk polishing protocol demonstrated significantly smoother and harder surfaces for both resins tested.

Evaluation of Mechanical Properties of ABS-like Resin for Stereolithography Versus ABS for Fused Deposition Modeling in Three-Dimensional Printing Applications for Odontology

This study investigates the differences in mechanical properties between acrylonitrile butadiene styrene (ABS) samples produced using fused deposition modeling (FDM) and stereolithography (SLA) using ABS filaments and ABS-like resin, respectively. The central question is to determine how these distinct printing techniques affect the properties of ABS and ABS-like resin and which method delivers superior performance for specific applications, particularly in dental treatments. The evaluation methods used in this study included Shore D hardness, accelerated aging, tensile testing, Izod impact testing, flexural resistance measured by a 3-point bending test, and compression testing. Poisson's ratio was also assessed, along with microstructure characterization, density measurement, confocal microscopy, dilatometry, wettability, Fourier-transform infrared spectroscopy (FTIR), and nanoindentation. It was concluded that ABS has the same hardness in both manufacturing methods; however, the FDM process results in significantly superior mechanical properties compared to SLA. Microscopy demonstrates a more accurate sample geometry when fabricated with SLA. It is also concluded that printable ABS is suitable for applications in dentistry to fabricate models and surgical guides using the SLA and FDM methods, as well as facial protectors for sports using the FDM method.

Mechanical and physical properties of splint materials for oral appliances produced by additive, subtractive and conventional manufacturing

OBJECTIVES

To investigate the flexural strength (FS), elastic modulus (E), Martens hardness (HM), water sorption (wsp), water solubility (wsl) and degree of conversion (DC) of 3D-printed, milled and injection molded splint materials.

METHODS

Specimens (N = 1140) were fabricated from five 3D-printed (GR-22 flex, GR-10 guide, ProArt Print Splint clear, V-Print Splint, V-Print Splint comfort), five milled (BioniCut, EldyPlus, ProArt CAD Splint clear, Temp Premium Flexible, Thermeo) and two injection molded (PalaXPress clear, Pro Base Cold) materials. FS, E, HM, wsp, wsl and DC were tested initially (24 h, 37 °C, H2O), after water storage (90 d, 37 °C, H2O) as well as after thermal cycling (5000 thermal cycles, 5/55 °C). Data were analyzed with Kolmogorov-Smirnov, Kruskal- Wallis, Mann-Whitney U test and Spearman's correlation (p < 0.05).

RESULTS

Initially, the mean flexural strength values ranged from 1.9 to 90.7 MPa for printed, 3.8 to 107 MPa for milled and 99.7 to 102 MPa for injection molded materials. The initial mean elastic modulus values were 0.0 to 2.4 GPa for printed, 0.1 to 2.7 GPa for milled and 2.8 GPa for injection molded materials. The initial mean Martens hardness values were 14.5 to 126 N/mm2 for printed, 50.2 to 171 N/mm2 for milled and 143 to 151 N/mm2 for injection molded materials. Initially, the mean water sorption values ranged from 23.1 to 41.2 μg/mm3 for printed, 4.5 to 23.5 μg/mm3 for milled and from 22.5 to 23.3 μg/ mm3 for injection molded materials. The initial mean water solubility values ranged from 2.2 to 7.1 μg/mm3 for printed, 0.0 to 0.5 μg/mm3 for milled and 0.1 to 0.3 μg/mm3 for injection molded materials. After water storage and thermal cycling most of the values decreased and some increased. The mean DC values ranged initially from 72.3 to 94.5 %, after water storage from 74.2 to 96.8 % and after thermal cycling from 75.6 to 95.4 % for the printed materials.

SIGNIFICANCE

The mechanical and physical properties of printed, milled and injection molded materials for occlusal devices vary and are influenced by aging processes. For clinical applications, materials need to be chosen according to the specific indications.

Digital manufacturing techniques and the in vitro biocompatibility of acrylic-based occlusal device materials

OBJECTIVES

Material chemistry and workflow variables associated with the fabrication of dental devices may affect the biocompatibility of the dental devices. The purpose of this study was to compare digital and conventional workflow procedures in the manufacturing of acrylic-based occlusal devices by assessing the cytotoxic potential of leakage products.

METHODS

Specimens were manufactured by 3D printing (stereolithography and digital light processing), milling, and autopolymerization. Print specimens were also subjected to different post-curing methods. To assess biocompatibility, a human tongue epithelial cell line was exposed to material-based extracts. Cell viability was measured by MTT assay while Western blot assessed the expression level of selected cytoprotective proteins.

RESULTS

Extracts from the Splint 2.0 material printed with DLP technology and post-cured with the Asiga Flash showed the clearest loss of cell viability. The milled and autopolymerized materials also showed a significant reduction in cell viability. However, by storing the autopolymerized material in dH2O for 12 h, no significant viability loss was observed. Increased levels of cytoprotective proteins were seen in cells exposed to extracts from the print materials and the autopolymerized material. Similarly to the effect on viability loss, storing the autopolymerized material in dH2O for 12 h reduced this effect.

CONCLUSIONS/CLINICAL RELEVANCE

Based on the biocompatibility assessments, clinical outcomes of acrylic-based occlusal device materials may be affected by the choice of manufacturing technique and workflow procedures.

Accuracy of the intaglio surface of 3D-printed hybrid resin-ceramic crowns, veneers and table-tops: An in vitro study

OBJECTIVES

The present study aims to examine the influence of the build angle on the accuracy (trueness and precision) of 3D printed crowns, table-tops and veneers with a hybrid resin-ceramic material.

METHODS

One crown, on table-top and one veneer were printed in five different build angles (0°, 30°, 45°, 60°, 90°) (n = 50) with the digital light processing (DLP) system (Varseo XS, Bego) using hybrid resin (Varseo Smile Crownplus A3, Bego). All printed restorations were scanned using the laboratory scanner (D2000, 3Shape) and matched onto the initial reference design in metrology software (Geomagic Control X, 3D Systems). The root mean square error (RMSE) was calculated between the scanned and reference data. The data was statistically analyzed using the Tukey multiple comparison test and Wilcoxon multiple comparison test.

RESULTS

The crown group showed higher trueness at 30° (0.021 ± 0.002) and 45° (0.020 ± 0.002), and table-tops at 0° (0.015 ± 0.001) and 30° (0.014 ± 0.001) (p < 0.0001). Veneers demonstrated higher trueness at 30° (0.016 ± 0.002) (p < 0.0001). All three restoration types demonstrated the lowest trueness at a 90° build angle and portrayed deviations along the z axis. The veneer and table-top groups showed the lowest precision at 90° (veneers: 0.021 ± 0.008; table-tops: 0.013 ± 0.003). The crown group portrayed the lowest precision at 45° (0.017 ± 0.005) (p < 0.0001).

CONCLUSION

The build angle of DLP-printed hybrid resin-ceramic restorations influences their accuracy.

CLINICAL SIGNIFICANCE

Considering the build angle is important to achieve a better accuracy of 3D-printed resin-ceramic hybrid restorations. This may help predict or avoid the interference points between a restoration and a die and minimize the clinical adjustments.

Biaxial Flexural Strength of Printed Splint Materials

One therapeutical alternative in the treatment of functional disorders is the use of printed oral splints. The mechanical properties of these materials are highly essential to their clinical effectiveness, and their performance may vary depending on factors such as cleaning, post-polymerization, or their orientation during construction. The objective of this in vitro investigation is to evaluate the effectiveness of the selected materials in terms of their biaxial flexural strength in relation to the criteria listed above. Splint materials were used in the printing of 720 discs. The printing process was carried out in different orientations in relation to the building platform. Either an automatic or manual cleaning process was performed on the samples. For post-polymerization, either an LED or Xenon light was utilized. A piston-on-three-ball test was used to measure the biaxial flexural strength (BFS) of the materials after they were stored in water for either 24 h or 60 days. The homogeneity of the data was controlled by employing the Levene method, and the differences between the groups were analyzed using the ANOVA and Bonferroni methods. After being stored for twenty-four hours, the mean BFS ranged anywhere from 79 MPa to 157 MPa. Following a period of sixty hours, the BFS exhibited a substantial drop and revealed values that ranged from 72 to 127 MPa. There was no significant difference that could be identified between the materials or between the various cleaning processes. The results of post-polymerization showed that the LED light produced higher means than the Xenon light did. In terms of position, the mean values varied greatly, with 0°'s mean value being 101 MPa, 45°'s mean value being 102 MPa, and 90°'s mean value being 115 MPa. The use of a build orientation of 90° and post-polymerization with LED light resulted in significantly increased biaxial flexural strength. According to this study, this design should be implemented in order to ensure that splint materials have the highest possible strength.

Vat Photopolymerization 3D Printing in Dentistry: A Comprehensive Review of Actual Popular Technologies

In this comprehensive review, the current state of the art and recent advances in 3D printing in dentistry are explored. This article provides an overview of the fundamental principles of 3D printing with a focus on vat photopolymerization (VP), the most commonly used technological principle in dental practice, which includes SLA, DLP, and LCD (or mSLA) technologies. The advantages, disadvantages, and shortcomings of these technologies are also discussed. This article delves into the key stages of the dental 3D printing process, from computer-aided design (CAD) to postprocessing, emphasizing the importance of postrinsing and postcuring to ensure the biocompatibility of custom-made medical devices. Legal considerations and regulatory obligations related to the production of custom medical devices through 3D printing are also addressed. This article serves as a valuable resource for dental practitioners, researchers, and health care professionals interested in applying this innovative technology in clinical practice.

Biofilm formation of C. albicans on occlusal device materials and antibiofilm effects of chitosan and eugenol

STATEMENT OF PROBLEM

Microbial adhesion on occlusal devices may lead to oral diseases such as candidiasis. Whether chitosan and eugenol provide antibiofilm effects is unclear.

PURPOSE

The purpose of this in vitro study was to evaluate the biofilm formation of C. albicans strains on occlusal device materials and the antibiofilm effects of chitosan and eugenol against C. albicans on these surfaces.

MATERIAL AND METHODS

A total of 88 specimens (5×10×2 mm) were produced from occlusal device materials with 4 production techniques: vacuum-formed thermoplastic (Group V), head-press (Group H), computer-aided design and computer-aided manufacture (CAD-CAM) (Group C), and 3-dimensionally (3D) printed (Group D) (n=22). After various finishing procedures, the surface properties of the specimens were evaluated by using surface free energy (SFE), surface roughness (SR) measurements, and elemental and topographic analysis. Biofilm formation of C. albicans strain and the antibiofilm effects of chitosan and eugenol against biofilm formation on these surfaces were also examined with a crystal violet assay. The distribution's normality was statistically analyzed with the Kolmogorov-Smirnov test. One-way and two-way analysis of variance with post hoc Tukey tests were used for statistical evaluations (α=.05).

RESULTS

Surface roughness values in Groups D and H were significantly higher than in other groups (P<.05). While the highest surface free energy values (except γp) were in Group V, Group C had the highest γp. The lowest biofilm value appeared in Group H. Chitosan exhibited an antibiofilm effect in all groups except Group H, while eugenol was effective in all groups.

CONCLUSIONS

The production method affected the susceptibility of occlusal device materials to the adhesion of C. albicans. Eugenol was an effective antibiofilm agent for device materials.

[Analysis of changes in the position of the temporomandibular joint articular disc during positioning splint therapy according to magnetic resonance imaging data]

THE AIM OF THE STUDY

Was to assess an impact of positioning occlusal splints made by various methods on the position of the articular disc of the temporomandibular joint according to MRI data.

MATERIALS AND METHODS

40 patients (8 men and 32 women) aged from 18 to 60 years with temporomandibular joint pain dysfunction syndrome were examined (ICD-10 code K07.60). Patients were treated with splint therapy using traditional splints made with combined method (20 patients) and subtractive occlusal splints made by CAD/CAM technology (20 patients). All patients had MRI of the temporomandibular joints before splint therapy and at the final stage of treatment to determine the position of the articular disc in the habitual occlusion and at maximum mouth opening.

RESULTS

After splint therapy, patients in both groups showed an improvement in the position of the articular disc in the usual occlusion: the rate of patients with bilateral dislocation of the articular disc decreased from 85% to 67.5%, and with unilateral articular disc dislocation decreased from 15% to 10%. With maximum mouth opening, complete reposition of the articular disc in both joints were recorded in 22.5%; the rate of patients with bilateral disorder of articular disc repositioning decreased from 85% to 67.5%, and with unilateral disorder of articular disc repositioning decreased from 15% to 10%.

CONCLUSIONS

Splint therapy had a pronounced positive clinical effect in patients with pain dysfunction syndrome in the temporomandibular joints. Splint therapy is more effective in correcting sagittal dislocation of the articular disc than transversal dislocation. The study showed comparable treatment results when using traditional and digital occlusal splints.

Effects of storage and toothbrush simulation on Martens hardness of CAD/CAM, hand-cast, thermoforming, and 3D-printed splint materials

OBJECTIVES

To investigate Martens hardness parameters of splint materials after storage in liquids and toothbrush simulation.

MATERIALS AND METHODS

Ten specimens per material and group were fabricated (hand-cast CAST, thermoformed TF, CAD/CAM-milled CAM, 3D-printed PS, PL, PK, PV), stored in air, water, coffee, red wine, and cleaning tablets and investigated after fabrication, 24 h, 2- and 4-week storage or toothbrushing. Martens hardness (HM), indentation hardness (HIT), indentation modulus (EIT), the elastic part of indentation work (ηIT), and indentation creep (CIT) were calculated (ISO 14577-1).

STATISTICS

ANOVA, Bonferroni post hoc test, between-subjects effects, Pearson correlation (α = 0.05).

RESULTS

HM varied between 30.8 N/mm2 for PS (water 4 weeks) and 164.0 N/mm2 for CAM (toothbrush). HIT values between 34.9 N/mm2 for PS (water 4 weeks) and 238.9 N/mm2 for CAM (toothbrush) were found. EIT varied between 4.3 kN/mm2 for CAM (toothbrush) and 1.8 kN/mm2 for PK (water 2 weeks). ηIT was found to vary between 16.9% for PS (water 4 weeks) and 42.8% for PL (toothbrush). CIT varied between 2.5% for PL (toothbrush) and 11.4% for PS (water 4 weeks). The highest impact was identified for the material (p ≤ 0.001).

CONCLUSIONS

Storage and toothbrushing influenced Martens parameters. The properties of splints can be influenced by the choice of materials, based on different elastic and viscoelastic parameters. High HM and EIT and low CIT might be beneficial for splint applications.

CLINICAL RELEVANCE

Martens parameters HM, EIT, and CIT might help to evaluate clinically relevant splint properties such as hardness, elasticity, and creep.

Mechanical and chemical characterization of contemporary occlusal splint materials fabricated with different methods: a systematic review

OBJECTIVE

To systematically review studies on various occlusal splint materials and describe their mechanical and chemical properties.

METHODS

MEDLINE (PubMed), Scopus, and Web of Science searches were conducted for in vitro studies focusing on occlusal splint materials. Two reviewers performed an assessment of the identified studies and data abstraction independently, and this was complimented by an additional hand search. The articles were limited to those in the English language that were published between January 1st, 2012, and December 1st, 2022.

RESULTS

The initial search yielded 405 search results of which 274 were selected for full-text review following abstract evaluation. 250 articles that did not meet the inclusion criteria were excluded, and the remaining 25 articles (with 1 article identified from the reference lists of included articles) providing mechanical and chemical values were used in this review. Poly methyl methacrylate (PMMA) -based occlusal splint materials showed the highest values in terms of hardness, wear resistance, flexural strength, flexural modulus, e-modulus, and fracture toughness. The material group with the highest water sorption and water solubility was 3D printed (PR) splint materials. In addition, the lowest degree of double bond conversion was also observed in this group of materials.

CONCLUSIONS

The outcome of this review suggests that mechanically and chemically acceptable properties can be attained with PMMA-based occlusal splint materials using both conventional and digital production methods. PR splint materials should not be considered as the primary choice for long-term treatments due to their low mechanical and chemical properties.

CLINICAL RELEVANCE

This review provides clinical recommendations for selecting the appropriate material and fabrication method for occlusal splints while taking the patients' needs and the materials´ mechanical and chemical properties into account.

Aging Processes and Their Influence on the Mechanical Properties of Printable Occlusal Splint Materials

Three-dimensional (3D)-printed occlusal splints are becoming more prevalent in the treatment of tooth substance loss due to their fast and cost-effective production. The purpose of this in vitro study was to investigate whether the mechanical properties (tensile strength-TS, modulus of elasticity in tension-ME, and Vickers hardness-HV) vary between the materials (printed dimethacrylate-based resins: Keyprint KeySplint soft-KEY, Luxaprint Ortho Plus-LUX, V-Print splint-VPR, printed methacrylate-based resins Freeprint splint 2.0-FRE, and milled methacrylate-based material, CLEAR splint-CLE), and the influence of aging processes (extraoral storage conditions and nightly or daily use) was examined. The printed methacrylate-based resins (FRE, LUX, and VPR) had much higher TS (43.7-48.5 MPa compared to 12.3-13.3 MPa), higher ME (2.01-2.37 GPa compared to 0.43-0.72 GPa), and higher HV (11.8-15.0 HV compared to 3.3-3.5 HV) than both of the methacrylate-based resins (KEY and CLE) after the production process. Although the TS, ME, and HV of the printed dimethacrylate resins (FRE, LUX, and VPR) decreased significantly under humid conditions with possibly elevated temperatures (thermocycling as well as 37 °C), these mechanical properties were significantly higher than both methacrylate-based resins (KEY and CLE). Therefore, printed dimethacrylate resins should be used rather than methacrylate-based resins for high expected masticatory forces, low wall thicknesses, or very long wearing times (≥6 months).

Effect of artificial aging on mechanical and physical properties of CAD-CAM PMMA resins for occlusal splints

PURPOSE

This study aimed to assess and compare the color stability, flexural strength (FS), and surface roughness of occlusal splints fabricated from heat-cured acrylic resin, milled polymethyl methacrylate (PMMA)-based resin, and 3D-printed (PMMA) based-resin.

MATERIALS AND METHODS

Samples of each type of resin were obtained, and baseline measurements of color and surface roughness were recorded. The specimens were divided into three groups (n = 10) and subjected to distinct aging protocols: thermomechanical cycling (TMC), simulated brushing (SB), and control (without aging). Final assessments of color and surface roughness and three-point bending test (ODM100; Odeme) were conducted, and data were statistically analyzed (2-way ANOVA, Tukey, P <.05).

RESULTS

Across all resin types, the most significant increase in surface roughness (Ra) was observed after TMC (P < .05), with the 3D-printed resin exhibiting the lowest Ra (P < .05). After brushing, milled resin displayed the highest Ra (P < .05) and greater color alteration (ΔE00) compared to 3D-printed resin. The most substantial ΔE00 was recorded after brushing for all resins, except for heat-cured resin subjected to TMC. Regardless of aging, milled resin exhibited the highest FS (P < .05), except when compared to 3D-printed resin subjected to TMC. Heat-cured resin exposed to TMC demonstrated the lowest FS, different (P < .05) from the control. Under control conditions, milled resin exhibited the highest FS, different (P < .05) from the brushed group. 3D-printed resin subjected to TMC displayed the highest FS (P < .05).

CONCLUSION

Among the tested resins, 3D-printed resin demonstrated superior longevity, characterized by minimal surface roughness and color alterations. Aging had a negligible impact on its mechanical properties.

The effects of manufacturing technologies on the surface accuracy of CAD-CAM occlusal splints

PURPOSE

To investigate the effects of the manufacturing technologies on the surface (cameo and intaglio) accuracy (trueness and precision) of computer-aided design and computer-aided manufacturing (CAD-CAM) occlusal splints.

MATERIALS AND METHODS

The digital design of the master occlusal splint was designed in a CAD software program. Six groups (n = 10) were tested in this study, including Group 1 - Milling (Wax), Group 2 - Heat-polymerizing, Group 3 - Milling (M series), Group 4 - Milling (DWX-51/52D), Group 5 - 3D-printing (Cares P30), and Group 6 - 3D-printing (M2). The study samples were placed in a scanning jig fabricated from putty silicone and Type III dental stone. The study samples were then scanned with a laboratory scanner at the intaglio and cameo surfaces, and the scanned files were exported in standard tessellation language (STL) file format. The master occlusal splint STL file, was used as a reference to compare with all scanned samples at the intaglio and cameo surfaces in a surface matching software program. Root mean square (RMS, measured in mm, absolute value) values were calculated by the software for accuracy comparisons. Group means were used as the representation of trueness, and the standard deviation for each group was calculated as a measure of precision. Color maps were recorded to visualize the areas of deviation between study samples and the master occlusal splint file. The data were normalized and transformed to rank scores, and one-way ANOVA was used to test for the differences between the groups. Pairwise comparisons were made between different groups. Fishers least square differences were used to account for the family-wise error rate. A 5% significance level was used for all the tests.

RESULTS

The null hypotheses were rejected. The manufacturing technologies significantly affected the trueness of occlusal splints at both intaglio and cameo surfaces (p < 0.001). At the cameo surfaces, Group 1 - Milling (Wax) (0.03 ± 0.02 mm), Group 3 - Milling (M series) (0.04 ± 0.01 mm), and Group 4 - Milling (DWX-51/52D) (0.04 ± 0.01 mm) had the smallest mean RMS values and highest trueness. Group 3 had the smallest standard deviation and highest precision among all groups (p < 0.001, except p = 0.005 when compared with Group 2). Group 5 had the largest standard deviation and lowest precision among all groups (p < 0.001). At the intaglio surfaces, Group 1 - Milling (Wax) (0.06 ± 0.01 mm) had the smallest RMS values and highest trueness among all groups (p < 0.001), and Group 2 - Heat-polymerizing (0.20 ± 0.03 mm) and Group 5 - 3D-printing (Cares P30) (0.15 ± 0.05 mm) had significantly larger mean RMS and standard deviation values than all other groups (p < 0.001), with lowest trueness and precision. In the color maps, Group 2 - Heat-polymerizing and Group 5 - 3D-printing (Cares P30) showed the most discrepancies with yellow and red (positive discrepancies) in most areas, and Group 1 - Milling (Wax) showed the best and most uniform surface matching with the most area in green.

CONCLUSION

The manufacturing technologies significantly affected the trueness and precision of occlusal splints at both intaglio and cameo surfaces. The 5-axis milling units and industrial-level CLIP 3D-printer could be considered to achieve surface accuracy of occlusal splints.

Mechanical Properties of 3D-Printed Occlusal Splint Materials

Data regarding the mechanical properties of three-dimensionally (3D) printed materials for occlusal splint manufacturing are scarce. The aim of the present study was to evaluate the flexural strength and surface hardness of modern 3D-printed occlusal splint materials and compare them with two control groups, namely, milled and conventional cold-polymerized occlusal splint materials. A total of 140 rectangular specimens were manufactured for the present study. The specimens were prepared in accordance with the International Organization for Standardization standards (ISO 20795-1:2013). Five 3D-printed (NextDent Ortho Rigid, Dental LT Clear, Dentona Flexisplint, Cosmos Bite Splint, and ProArt Print Splint), one milled (ProArt CAD Splint), and one cold-polymerized (ProBase Cold) occlusal splint materials were used to determine flexural strength and surface hardness values. The three-point flexure test was used for the determination of flexural strength values, while Vickers hardness was measured to determine surface hardness. Ten specimens (n = 10) of each material were tested using these procedures. One-way ANOVA and Tukey's post-hoc test were used to analyze the obtained results (α = 0.05). The values of flexural strength ranged from 46.1 ± 8.2 MPa to 106 ± 8.3 MPa. The Vickers hardness values ranged from 4.9 ± 0.5 VHN to 20.6 ± 1.3 VHN. Significant differences were found among the tested materials (p < 0.0001). The milled and cold-polymerized materials yielded higher values for both flexural strength (only one 3D-printed resin had comparable results to cold-polymerized acrylics) and surface hardness. There are differences in the mechanical properties of the various tested occlusal splint materials. The flexural strength of most of the 3D-printed materials and their surface hardness values are still inferior when compared to the milled or cold-polymerized materials.

Effect of layer thickness, build angle, and viscosity on the mechanical properties and manufacturing trueness of denture base resin for digital light processing

OBJECTIVES

To investigate effects of layer thickness, build angle, and viscosity on the mechanical properties and trueness of denture base resins used for digital light processing (DLP).

METHODS

Two denture base resins for DLP in different viscosity (high and low) were tested by using two manufacturing parameters:1) layer thickness (LT) (50- or 100-μm) and 2) build angle (BA) (0-, 45-, and 90-degree). disk- and bar-shaped specimens were used to evaluate hardness and flexural strength, respectively. Denture base specimens were used to examine trueness, and the deviation was calculated as the root mean square. Three-way analysis of variance (ANOVA) was conducted to determine the interaction among the three factors (viscosity, LT, and BA). Statistical significance was set at P < .05.

RESULTS

Effects of LT and BA on hardness differed according to viscosity, with significant interactions among three factors (P=.027). Regardless of LT or BA, the low-viscosity group had higher hardness than the high-viscosity group (P<.001). In terms of flexural strength, no significant interaction was detected between the factors (P=.212), however, the effects of LT and BA were significant (P=.003 and P<.001, respectively). Regarding trueness, a significant interaction was observed between viscosity and BA (P=.001). Low-viscosity group had higher trueness than high-viscosity group when the 45- and 90-degree BA were applied (P<.001).

CONCLUSIONS

LT and BA significantly affected the mechanical properties and trueness of the 3DP denture base, depending on the viscosity. For hardness and trueness, using low-viscosity resin and manufacturing with 50-μm LT and 45-degree BA are recommended.

CLINICAL SIGNIFICANCE

Resin viscosity affects the influence of LT and BA on the hardness, flexural strength, and trueness of DLP-generated denture bases. A 50-μm LT and 45-degree BA can be used with a low-viscosity resin to fabricate denture bases with higher hardness and trueness.

Effects of Polishing and Artificial Aging on Mechanical Properties of Dental LT Clear® Resin

Three-dimensional printing has become incorporated into various aspects of everyday life, including dentistry. Novel materials are being introduced rapidly. One such material is Dental LT Clear by Formlabs, a resin used for manufacturing occlusal splints, aligners, and orthodontic retainers. In this study, a total of 240 specimens, comprising two shapes (dumbbell and rectangular), were evaluated through compression and tensile tests. The compression tests revealed that the specimens were neither polished nor aged. However, after polishing, the compression modulus values decreased significantly. Specifically, the unpolished and nonaged specimens measured 0.87 ± 0.02, whereas the polished group measured 0.086 ± 0.03. The results were significantly affected by artificial aging. The polished group measured 0.73 ± 0.05, while the unpolished group measured 0.73 ± 0.03. In contrast, the tensile test proved that the specimens showed the highest resistance when the polishing was applied. The artificial aging influenced the tensile test and reduced the force needed to damage the specimens. The tensile modulus had the highest value when polishing was applied (3.00 ± 0.11). The conclusions drawn from these findings are as follows: 1. Polishing does not change the properties of the examined resin. 2. Artificial aging reduces resistance in both compression and tensile tests. 3. Polishing reduces the damage to the specimens in the aging process.

Effects of storage and toothbrush simulation on color, gloss, and roughness of CAD/CAM, hand-cast, thermoforming, and 3D-printed splint materials

Objectives

The aim was to investigate color, gloss, or roughness of splint materials after storage in liquids and toothbrush simulation.

Materials and methods

A total of 58 × 8 (n = 10 per material and group) specimens were fabricated (hand-cast, thermoforming, CAD/CAM-milled, 3D-printed materials); stored in air, water, coffee, red wine, and cleaning tablets; and investigated after fabrication, 24 h, two-, and four-week storage or toothbrushing. Color values (L*, a*, b*; ISO 11664–4:2008; CM–3500d, Konica-Minolta), gloss (ISO 2813:2014), and roughness values were determined (3D laser-scanning-microscope, KJ 3D, Keyence) before and after simulation or storage. Statistics: Levene-test, one-way ANOVA, Bonferroni post hoc test, between-subjects effects, Pearson correlation (α = 0.05).

Results

Color, gloss, and roughness altered due to contact with staining solutions/toothbrush simulation. Highest impact on color, gloss, and roughness presented the material followed by storage time (ΔE material (η2 = 0.239/p < 0.001), storage time (η2 = 0.179/p < 0.001); gloss (η2 = 0.751/p < 0.001) (η2 = 0.401/p < 0.001); Ra/Rz (η2 ≥ 0.801/p < 0.001) (η2 ≥ 0.416/p < 0.001)). Correlations were found between Rz and Ra (Pearson 0.887/p ≤ 0.001) or Rz and ΔE (0.517/p ≤ 0.001) or Ra and ΔE (0.460/p ≤ 0.001).

Conclusions

Storage and toothbrushing were accompanied by a change in color, gloss, and roughness. Almost all materials showed visible discoloration after 4 weeks of storage. Gloss values decreased as storage time increased. The initial roughness and polishability were better with harder materials.

Clinical relevance.

Milled and 3D printed splints show good color, gloss, and roughness resistance after 4-week storage or toothbrush application.

Evaluation of wear behaviour of various occlusal splint materials and manufacturing processes

OBJECTIVES

To investigate the volumetric and vertical loss of occlusal splints manufactured by conventional (heat-cure), subtractive (CAD/CAM) and additive (3D-printing) methods.

METHODS

Six occlusal splint materials were investigated (n = 126), using three manufacturing methods: heat-cured, CAD/CAM and 3D-printed built-in three different printing angles (0°,45°and 90°). Block-on-ring wear testing was performed with extracted human molars as the antagonist. All samples were tested with an applied force of 49N at 1 Hz and 60RPM in artificial saliva at 37 °C for six and 12 months. Scanning electron microscopy images were analysed to evaluate the wear on the tooth enamel and in the splint material. Volumetric and vertical wear loss were statistically analysed.

RESULTS

The lowest volumetric and vertical loss was observed in CAD-CAM materials (6.44 ± 1.77 mm³ and 48.3 ± 7.14 μm) with no statistical significance to the heat-cured material (17.22 ± 9.23 mm³ and 148 ± 121.1 μm) after 12 months (p < 0.172). The mean volumetric loss of 3D printed materials ranged from 0.25 ± 0.15 mm³ to 0.29 ± 0.1 4mm³ with no statistical difference, whereas, the differences in vertical loss from 131.63 ± 44.1 μm to 493 ± 79.19 μm were statistically significant (p < 0.001). The highest vertical loss was observed in the KeySplint Soft 3D printed at 90° (385.35 ± 82.37 μm), whereas FreePrint Splint 2.0 with a build angle of 0° had the highest volumetric loss (204.59 ± 25.67 mm³).

CONCLUSION

CAD-CAM material had the highest wear resistance followed by heat-cured material.KeySplint Soft and FreePrint Splint 2.0 3D printed materials would be preferred for patients that do not have severe bruxing episodes. No significant wear of human enamel after six and 12 months was observed under SEM for any tested materials.

Dynamic fatigue of 3D-printed splint materials

OBJECTIVES

Printed splints may be an alternative treatment for functional disorders. In addition to the selection of materials, the influence of cleaning or polymerisation can affect the dynamic behaviour and fatigue limit of printed materials.

MATERIAL AND METHODS

96 discs (n = 6 per group, 16mmx2mm) were printed (P30+ DLP-printer, Straumann, CH; 100 μm layer) from splint materials (M1: Luxaprint OrthoPlus, DMG, G; M2: V-Print Splint, Voco, G). Specimens were either automatically cleaned (C1: Straumann P Wash, Straumann, CH) or manually cleaned (C2: Voco Pre-/Main-Clean protocol, Voco, G). Post polymerisation was performed with LED (P1: Cure, Straumann, CH) or Xenon light (P2: Otoflash N171, Ernst Hinrichs Dental, G). The flexural fatigue limit was determined under cyclic loading in terms of a staircase approach with a piston-on-3-ball-test according to ISO 6872 after 24 h or 60 days water storage (37 °C). Specimens were preloaded with 50N and dynamic force was applied for 10⁵ loadings per step (f = 3Hz; steps 1: 50N-100N, 2: 50N-150N, 3: 50N-200N, 4: 50N-250N; F1000, Prematec, G; water at 37 °C).

STATISTICS

Kaplan Maier Log Rank (Mantel-Cox) test, ANOVA, Pearson correlations, Levene-test (α = 0.05, SPSS 26.0, IBM, Armonk, NY, USA)).

RESULTS

Mean survival cycles after 24 h of storage varied between 40388 (M1C2P2) and 195140 (M2C2P1) cycles and after 60 d decreased to 14022 (M1C2P2) and 173237 (M2C1P1). Kaplan Maier Log Rank test revealed significant differences between the material combinations. For M1 cleaning (Pearson: 0.346, p = 0.016) and for M2 polymerisation (Pearson: 0.616, p = 0.000) significantly influenced the number of loading cycles. Intermediate effects were found for material (p = 0.026), cleaning (p = 0.024) and polymerisation (p = 0.000) as well as the combination of material and polymerisation (p = 0.008).

CONCLUSIONS

The results show that the number of possible loading cycles of additively manufactured splint specimens depends on the type of material, their cleaning and post-polymerisation.

CLINICAL SIGNIFICANCE

Materials, cleaning and post-polymerisation of additive manufacturing processes should be matched to improve dynamic loading performance of splint materials.

Wear Behavior of Occlusal Splint Materials Manufactured By Various Methods: A Systematic Review

PURPOSE

To systematically review studies on various materials and methods used for wear testing of occlusal devices and their antagonists in vitro and in vivo.

METHODS

An electronic search in OVID, Web of Science, PubMed and Scopus was conducted using the following terms (MeSH words) with any synonyms and closed terms: "Splint*" OR "occlusal splint*" OR "night guard" OR "occlusal device" OR "occlusal devices" OR "deprogrammer" OR "bite splint" OR "bite plane" OR "orthotic appliance*" OR "orthotic devices" AND "wear" OR "two-body wear" OR "three-body wear" OR "tooth wear" OR "wear measurement*" OR "wear behaviour" OR "wear behavior" OR "abrasion" AND "Polymethyl Methacrylate" OR "PMMA" OR "acrylic resin*" OR "dental material*" OR "dental enamel" OR "CAD" OR "CAM" OR "PEEK" OR "material* testing". Database search was limited to English-language publications and published between 2001 and 1st of September 2021. A further hand search was done to ensure all materials were captured.

RESULTS

After the removal of duplicates, 115 studies were identified, and 11 were chosen for review. Studies showed that the lowest volumetric loss was observed in PEEK occlusal device materials, whereas heat-cure, CAD-milled, and 3D printed occlusal device materials had no significant difference in wear. Vacuum-formed materials showed the highest wear among all groups. Testing parameters were found to be inconsistent across all studies.

CONCLUSION

There is a need for standardization of in vitro and in vivo wear measurement and testing protocols as this study revealed a wide variety of testing protocols which potentially could influence the outcome. Polishing procedures are required for the material. Limited studies are available on 3D printed occlusal device materials and would therefore require further investigation, especially on printing build angles and settings. Further clinical studies would be advantageous to provide guidance on the selection of the best occlusal device material that would last the longest without remake.

Investigating the mechanical and optical properties of novel Urethandimethacrylate (UDMA) and Urethanmethacrylate (UMA) based rapid prototyping materials

OBJECTIVE

This study is focused on testing experimental rapid prototyping materials for occlusal splints made from Urethandimethacrylate (UDMA) and Urethanmethacrylate (UMA).

METHODS

Materials were mixed from UDMA and UMA in ratios of 1.0:0.0, 0.75:0.25, 0.5:0.5, 0.25:0.75 and 0.0:1.0. Specimens were printed using digital light processing (DLP). After post-processing, the specimens underwent testing on flexural strength, modulus of elasticity, hardness, wear behavior, surface roughness, gloss and color stability. All tests were performed after 24 h (baseline) and 10 days of water storage (aging). Splints underwent cyclic pull-off and insertion testing, which was alongside simulated using finite element analysis.

RESULTS

The mechanical properties were significantly influenced by changes in the UDMA:UMA ratio. Statistical analysis revealed that increased amounts of UMA correlated with a decrease in flexural strength (92.0 to 30.7 MPa), modulus of elasticity (2.4 to 0.6 GPa), hardness (155.1 to 102.0 N/mm²) and wear resistance (-1394.9 to -1742.1 μm). Materials with higher amounts of UMA were also more likely to be influenced by water storage. Specimens with 75% and 100% UMA content were partly not analyzable due to soft consistency. Optical properties showed only minor influence from UMA content and aging. Differences in surface roughness (3.9 to 2.4 μm) and color stability were insignificant. Gloss was partly influenced by the UDMA:UMA ratio and water storage. Mean survival rates for cyclic pull-off and insertion testing ranged from 2537 to 23,857 cycles. A correlation between the amount of UMA and survival rates was observed.

SIGNIFICANCE

The addition of up to 25% UMA showed promising results, complying with clinical standards and delivering acceptable results in the cyclic pull-off and insertion test. Further investigation on increments between 0 and 25% UMA could help to find an optimum.