Long-term mechanical properties of a novel low-modulus bone cement for the treatment of osteoporotic vertebral compression fractures

Mechanical characterization and cytocompatibility of linoleic acid modified bone cement for percutaneous cement discoplasty

Minimally invasive spine treatments have been sought after for elderly patients with comorbidities suffering from advanced degenerative disc disease. Percutaneous cement discoplasty (PCD) is one such technique where cement is injected into a degenerated disc with a vacuum phenomenon to relieve patients from pain. Adjacent vertebral fractures (AVFs) are however an inherent risk, particularly for osteoporotic patients, due to the high stiffness of the used cements. While low-modulus cements have been developed for vertebroplasty through the addition of linoleic acid, there are no such variations with a high-viscosity base cement, which is likely needed for the discoplasty application. Therefore, a low-modulus polymethyl methacrylate was developed by the addition of 12%vol. linoleic acid to a high-viscosity bone cement (hv-LA-PMMA). Initial experimental validation of the cement was performed by mechanical testing under compression over a period of 24 weeks, after storage in 37 °C phosphate buffer saline (PBS) solution. Furthermore, cement extracts were used to evaluate residual monomer release and the cytotoxicity of hv-LA-PMMA using fibroblastic cells. Relative to the base commercial cement, a significant reduction of Young's modulus and compressive strength of 36% and 42% was observed, respectively. Compression-tension fatigue tests at 5 MPa gave an average fatigue limit of 31,078 cycles. This was higher than another low-modulus cement and comparable to the fatigue properties of the disc annulus tissue. Monomer release tests showed that hv-LA-PMMA had a significantly higher release between 24 h and 7 days compared to the original bone cement, similarly to other low-modulus cements. Also, the control cement showed cytocompatibility at all time points of extract collection for 20-fold dilution, while hv-LA-PMMA only showed the same for extract collections at day 7. However, the 20-fold dilution was needed for both the control and the hv-LA-PMMA extracts to demonstrate more than 70% fibroblast viability at day 7. In conclusion, the mechanical testing showed promise in the use of linoleic acid in combination with a high-viscosity PMMA cement to achieve properties adequate to the application. Further testing and in vivo studies are however required to fully evaluate the mechanical performance and biocompatibility of hv-LA-PMMA for possible future clinical application.

Rheological Analysis and Evaluation of Measurement Techniques for Curing Poly(Methyl Methacrylate) Bone Cement in Vertebroplasty

Vertebroplasty is a minimally invasive surgical procedure used to treat vertebral fractures, which conventionally involves injecting poly(methyl methacrylate) (PMMA) bone cement into the fractured vertebra. A common risk associated with vertebroplasty is cement leaking out of the vertebra during the injection, which may occur due to a lack of understanding of the complex flow behavior. Therefore, experiments to quantify the cement's flow properties are necessary for understanding and proper handling of the bone cement. In this study, we aimed to characterize the behavior of PMMA bone cement in its curing stages to obtain parameters that govern the flow behavior during injection. We used rotational and oscillatory rheometry for our measurements, as well as a custom-made injector setup that replicated a typical vertebroplasty setting. Our results showed that the complex viscoelastic behavior of bone cement is significantly affected by deformations and temperature. We found that the results from rotational tests, often used for characterizing the bone cement, are susceptible to measurement artifacts caused by wall slip and "ridge"-like formations in the test sample. We also found the Cox-Merz rule to be conditionally valid, which affects the use of oscillatory tests to obtain the shear-thinning characteristics of bone cement. Our findings identify important differences in the measured flow behavior of PMMA bone cement when assessed by different rheological methods, an understanding that is crucial for its risk-free usage in downstream medical applications.

Advancements in poly(methyl Methacrylate) bone cement for enhanced osteoconductivity and mechanical properties in vertebroplasty: A comprehensive review

The evolution of polymethyl methacrylate (PMMA) based bone cement (BC) from plexiglass to a biomaterial has revolutionized the joint and vertebral arthroplasties field. This widely used grouting material possesses exceptional properties for medical applications, including excellent biocompatibility, impressive mechanical strength, and favorable handling characteristics. PMMA-based BC is preferred in challenging conditions such as osteoporotic vertebral compression fractures, scoliosis, vertebral hemangiomas, spinal metastases, and myelomas, where it is crucial in withstanding stress. This review aims to comprehensively analyze the available reports and guide further research toward enhanced formulations of vertebral BC, focusing on its osteoconductive and mechanical properties. Furthermore, the review emphasizes the significant impact of BC's mechanical properties and osteoconductivity on the success and longevity of vertebroplasty procedures.

Advances in materials-based therapeutic strategies against osteoporosis

Osteoporosis is caused by the disruption in homeostasis between bone formation and bone resorption. Conventional management of osteoporosis involves systematic drug administration and hormonal therapy. These treatment strategies have limited curative efficacy and multiple adverse effects. Biomaterials-based therapeutic strategies have recently emerged as promising alternatives for the treatment of osteoporosis. The present review summarizes the current status of biomaterials designed for managing osteoporosis. The advantages of biomaterials-based strategies over conventional systematic drug treatment are presented. Different anti-osteoporotic delivery systems are concisely addressed. These materials include injectable hydrogels and nanoparticles, as well as anti-osteoporotic bone tissue engineering materials. Fabrication techniques such as 3D printing, electrostatic spinning and artificial intelligence are appraised in the context of how the use of these adjunctive techniques may improve treatment efficacy. The limitations of existing biomaterials are critically analyzed, together with deliberation of the future directions in biomaterials-based therapies. The latter include discussion on the use of combination strategies to enhance therapeutic efficacy in the osteoporosis niche.

Low-Modulus PMMA Has the Potential to Reduce Stresses on Endplates after Cement Discoplasty

Cement discoplasty has been developed to treat patients with advanced intervertebral disc degeneration. In discoplasty, poly(methylmethacrylate) (PMMA) bone cement is injected into the disc, leading to reduced pain and certain spinal alignment correction. Standard PMMA-cements have much higher elastic modulus than the surrounding vertebral bone, which may lead to a propensity for adjacent fractures. A PMMA-cement with lower modulus might be biomechanically beneficial. In this study, PMMA-cements with lower modulus were obtained using previously established methods. A commercial PMMA-cement (V-steady^®, G21 srl) was used as control, and as base cement. The low-modulus PMMA-cements were modified by 12 vol% (LA12), 16 vol% (LA16) and 20 vol% (LA20) linoleic acid (LA). After storage in 37 °C PBS from 24 h up to 8 weeks, specimens were tested in compression to obtain the material properties. A lower E-modulus was obtained with increasing amount of LA. However, with storage time, the E-modulus increased. Standard and low-modulus PMMA discoplasty were compared in a previously developed and validated computational lumbar spine model. All discoplasty models showed the same trend, namely a substantial reduction in range of motion (ROM), compared to the healthy model. The V-steady model had the largest ROM-reduction (77%), and the LA20 model had the smallest (45%). The average stress at the endplate was higher for all discoplasty models than for the healthy model, but the stresses were reduced for cements with higher amounts of LA. The study indicates that low-modulus PMMA is promising for discoplasty from a mechanical viewpoint. However, validation experiments are needed, and the clinical setting needs to be further considered.

Mechanical properties and biomedical application characteristics of degradable polylactic acid-Mg-Ca3(PO4)2 three-phase composite

Polylactic acid (PLA), pure magnesium powder, and calcium phosphate powder were used to form a three-phase degradable biomedical composite. The effects of various powder proportions in polylactic acid-Mg-Ca₃(PO₄)₂ composites were analyzed through mechanical and biological tests, which revealed that both the tensile and impact strength of the composite increased. Additionally, ductility presented only after a small proportion of powder was added. Hardness slightly increased because of dispersion strengthening. Furthermore, the addition of pure magnesium and calcium phosphate accelerated the degradation rate, and biocompatible salts were generated after degradation, which can improve healing and renewal in bone tissue. None of the composites exhibited cytotoxicity, meeting biological safety requirements. Overall, PLA10M10C (10 wt.% Mg, 10 wt.% Ca₃(PO₄)₂) exhibited superior performance. Accordingly, PLA10M10C can serve as a reference for degradable biomedical material applications in orthopedic implants.

Structural geometries and mechanical properties of vertebral implant with honeycomb sandwich structure for vertebral compression fractures: a finite element analysis

Background

Because of osteoporosis, traffic accidents, falling from high places, and other reasons, the vertebral body can be compressed and even collapse. Vertebral implants can be used for clinical treatment. Because of the advantages of honeycomb sandwich structures, such as low cost, less material, light weight, high strength, and good cushioning performance. In this paper, the honeycomb sandwich structure was used as the basic structure of vertebral implants.

Methods

The orthogonal experiment method is applied to analyse the size effect of honeycomb sandwich structures by the finite element method. Based on the minimum requirements of three indexes of peak stress, axial deformation, and anterior–posterior deformation, the optimal structure size was determined. Furthermore, through local optimization of the overall structure of the implant, a better honeycomb sandwich structure vertebral implant was designed.

Results

The optimal structure size combination was determined as a panel thickness of 1 mm, wall thickness if 0.49 mm, cell side length of 1 mm, and height of 6 mm. Through local optimization, the peak stress was further reduced, the overall stress distribution was uniform, and the deformation was reduced. The optimized peak stress decreased to 1.041 MPa, the axial deformation was 0.1110%, and the anterior–posterior deformation was 0.0145%. A vertebral implant with good mechanical performance was designed.

Conclusions

This paper is the first to investigate vertebral implants with honeycomb sandwich structures. The design and analysis of the vertebral implant with a honeycomb sandwich structure were processed by the finite element method. This research can provide a feasible way to analyse and design clinical implants based on biomechanical principles.