1
|
Hemida MH, Moustafa H, Mehanny S, Morsy M, Abd El Rahman EN, Ibrahim MM. Valorization of Eichhornia crassipes for the production of cellulose nanocrystals further investigation of plethoric biobased resource. Sci Rep 2024; 14:12387. [PMID: 38811644 PMCID: PMC11136955 DOI: 10.1038/s41598-024-62159-z] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/31/2023] [Accepted: 05/14/2024] [Indexed: 05/31/2024] Open
Abstract
Chemical processing is among the significant keys to tackle agro-residues utilization field, aiming to obtain value-added materials. Extraction of cellulose nanocrystals (CNCs) is an emerging route to valorize lignocellulosic wastes into high value particles. In this investigation, effect of acidic hydrolysis duration was monitored on size and morphology of obtained crystals; namely: CNCs from Nile roses fibers (NRFs) (Eichhornia crassipes). Different acidic hydrolysis duration range or different characterization techniques set this article apart from relevant literature, including our group research articles. The grinded NRFs were firstly subjected to alkaline and bleaching pretreatments, then acid hydrolysis process was carried out with varied durations ranging from 5 to 30 min. Microcrystalline cellulose (MCC) was used as reference for comparison with NRFs based samples. The extracted CNCs samples were investigated using various techniques such as scanning electron microscopy (SEM), Atomic force microscopy (AFM), Raman spectroscopy, and thermogravimetric (TGA) analysis. The figures gotten from SEM and AFM depicted that NRFs based CNCs appeared as fibril-like shapes, with reduced average size when the NRFs underwent pulping and bleaching processes. This was indicated that the elimination of hemicellulose and lignin components got achieved successfully. This outcome was proven by chemical composition measurements and TGA/DTG curves. On the other hand, AFM-3D images indicated that CNCs topology and surface roughness were mostly affected by increasing hydrolysis durations, besides smooth and homogeneous surfaces were noticed. Moreover, Raman spectra demonstrated that the particle size and crystallinity degree of NRFs based CNCs can be affected by acidic hydrolysis durations and optimum extraction time was found to be 10 min. Thermal stability of extracted CNCs-NRFs and CNCs-MCC was measured by TGA/DTG and the kinetic models were suggested to identify the kinetic parameters of the thermal decomposition of CNCs for each acid hydrolysis duration. Increasing hydrolysis duration promoted thermal stability, particularly for NRFs based CNCs. Results showcased in this article add new perspective to Nile rose nanocellulose and pave down the way to fabricate NRFs based humidity nano-sensors.
Collapse
Affiliation(s)
- Mohamed H Hemida
- Agricultural Engineering Department, Faculty of Agriculture, Cairo University, Giza, Egypt
| | - Hesham Moustafa
- Department of Polymer Metrology & Technology, National Institute of Standards (NIS), Tersa Street, El Haram, P.O Box 136, Giza, 12211, Egypt
- Bioanalysis Laboratory, National Institute of Standards (NIS), Tersa Street, El Haram, P.O Box 136, Giza, 12211, Egypt
| | - Sherif Mehanny
- Department of Mechanical Design and Production, Faculty of Engineering, Cairo University, Giza, Egypt
| | - Mohamed Morsy
- Building Physics and Environment Institute, Housing and Building National Research Center (HBRC), Dokki, Giza, Egypt.
- Nanotechnology Research Center (NTRC), The British University in Egypt (BUE), El Sherouk City, Suez Desert Road, Cairo, 11837, Egypt.
| | - Eid N Abd El Rahman
- Agricultural Engineering Department, Faculty of Agriculture, Cairo University, Giza, Egypt
| | - Mohamed M Ibrahim
- Agricultural Engineering Department, Faculty of Agriculture, Cairo University, Giza, Egypt.
| |
Collapse
|
2
|
Dhahi RM, Mohammed MM, Mikhlif HM. Biowaste Valorization of Palm Tree Phoenix dactylifera L. for Nanocellulose Production. IET Nanobiotechnol 2024; 2024:7867463. [PMID: 38938743 PMCID: PMC11208844 DOI: 10.1049/2024/7867463] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/23/2024] [Revised: 05/06/2024] [Accepted: 05/16/2024] [Indexed: 06/29/2024] Open
Abstract
The desire to reduce reliance on oil resources arises from the concerns about carbon footprint and nonrenewability. Conversely, the global presence of over 100 million palm trees poses a significant challenge due to the substantial amount of biowaste generated annually. Additionally, the use of nanocellulose (NC) as a cost-effective material is steadily gaining recognition for its growing adaptability over time. The main goal of this study is to biosynthesized NC from Iraqi date palm Phoenix dactylifera leaves waste with low-concentration acid-alkali treatment. The date palm leaves waste yields 20 g of NC from 100 g of leaves before acid hydrolysis treatment. The chemical components of biosynthesized NC were 47.90%, 26.78%, and 24.67% for α-cellulose, hemicellulose, and lignin, respectively. In order to study their properties, NC from raw date palm leaves was studied by microscopic techniques such as scanning electron microscopy (SEM), energy dispersive X-ray (EDX) spectroscopy, and atomic force microscope (AFM). SEM results revealed rod-like structured NC as well as combined long-fine fibrous structures rather than compacted bundles with sizes ranging between 31 and 74 nm. With EDX, all spectra exhibit the peaks of carbon and oxygen as the main elements with 63.8% and 10.44%, respectively, in their compositions, which relate to the typical composition of cellulose. The 3D image of AFM NC with a tapping mode presented a highly uniform distribution of NC with a size of ∼15 nm. The statistical roughness analysis shows that the obtained roughness average is 7.20 nm with the root-mean-square roughness value of 21.56 nm, which corresponded relatively with the micrographs of SEM. The results of this study demonstrate the promise of using date palm waste as raw material to produce NC as green nanocomposite from biodegradable nanomaterials for water purification and sustained drug delivery for biomedical applications. In this regard and because of the insufficient reports about the extraction of NC from palm tree leaves waste, the objective of this study was designed to fabricate NC biologically from fibers sourced from the waste of Iraqi date palm P. dactylifera leaves that left in agricultural lands or burned, which can be an ecological and health problem as a bionanocomposites in the medical and industrial field and as alternative resources of wood materials.
Collapse
|
3
|
Chaoua S, Flahaut S, Cornu B, Hiligsmann S, Chaouche NK. Unlocking the potential of Algerian lignocellulosic biomass: exploring indigenous microbial diversity for enhanced enzyme and sugar production. Arch Microbiol 2024; 206:277. [PMID: 38789671 DOI: 10.1007/s00203-024-04011-6] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/03/2024] [Revised: 05/15/2024] [Accepted: 05/19/2024] [Indexed: 05/26/2024]
Abstract
Nowadays, natural resources like lignocellulosic biomass are gaining more and more attention. This study was conducted to analyse chemical composition of dried and ground samples (500 μm) of various Algerian bioresources including alfa stems (AS), dry palms (DP), olive pomace (OP), pinecones (PC), and tomato waste (TW). AS exhibited the lowest lignin content (3.60 ± 0.60%), but the highest cellulose (58.30 ± 2.06%), and hemicellulose (20.00 ± 3.07%) levels. DP, OP, and PC had around 30% cellulose, and 10% hemicellulose. OP had the highest lignin content (29.00 ± 6.40%), while TW contained (15.70 ± 2.67% cellulose, 13.70 ± 0.002% hemicellulose, and 17.90 ± 4.00% lignin). Among 91 isolated microorganisms, nine were selected for cellulase, xylanase, and/or laccase production. The ability of Bacillus mojavensis to produce laccase and cellulase, as well as B. safensis to produce cellulase and xylanase, is being reported for the first time. In submerged conditions, TW was the most suitable substrate for enzyme production. In this conditions, T. versicolor K1 was the only strain able to produce laccase (4,170 ± 556 U/L). Additionally, Coniocheata hoffmannii P4 exhibited the highest cellulase activity (907.62 ± 26.22 U/L), and B. mojavensis Y3 the highest xylanase activity (612.73 ± 12.73 U/L). T. versicolor K1 culture showed reducing sugars accumulation of 18.87% compared to initial concentrations. Sucrose was the predominant sugar detected by HPLC analysis (13.44 ± 0.02 g/L). Our findings suggest that T. versicolor K1 holds promise for laccase production, while TW represents a suitable substrate for sucrose production.
Collapse
Affiliation(s)
- Samah Chaoua
- Laboratoire de Mycologie, de Biotechnologie et de l'Activité Microbienne (LaMyBAM), Département de Biologie Appliquée, Université des Frères Mentouri Constantine 1, Constantine, Algeria.
- Laboratoire de Microbiologie Appliquée, Université Libre de Bruxelles, Brussels, Belgium.
| | - Sigrid Flahaut
- Laboratoire de Microbiologie Appliquée, Université Libre de Bruxelles, Brussels, Belgium
| | | | - Serge Hiligsmann
- Bioengineering Department, CELABOR Research Center, Herve, Belgium
| | - Noreddine Kacem Chaouche
- Laboratoire de Mycologie, de Biotechnologie et de l'Activité Microbienne (LaMyBAM), Département de Biologie Appliquée, Université des Frères Mentouri Constantine 1, Constantine, Algeria
| |
Collapse
|
4
|
Raza M, Jawaid M, Abu-Jdayil B. Extraction of lignin-containing nanocellulose fibrils from date palm waste using a green solvent. Int J Biol Macromol 2024; 267:131540. [PMID: 38608992 DOI: 10.1016/j.ijbiomac.2024.131540] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/08/2024] [Revised: 03/29/2024] [Accepted: 04/09/2024] [Indexed: 04/14/2024]
Abstract
Lignin-containing nanocellulose (LNC) is a compelling alternative to traditional nanocellulose (NC), it offers enhanced yields and a reduction in the demand for toxic chemicals. This research involves the isolation of LNC from date palm waste using a green hydrolysis process and its subsequent characterization. The potential of using ionic liquids (ILs) as green solvents to isolate LNC has not yet been explored. Our findings suggest that 1-ethyl-3-methylimidazolium chloride ([Emim]Cl) can hydrolyze partially delignified and unbleached lignocellulose, achieving LNC synthesis. The obtained LNC showed a higher yield than its NC counterpart and exhibited rod-shaped fibers with nanoscale diameters and micrometer lengths, indicating a high aspect ratio. Dynamic Light Scattering (DLS) results indicate average particle sizes of 143.20 nm for NC and 282.30 nm for LNC, with a narrow particle size distribution conforming their monodisperse behavior. Thermogravimetric analysis and differential scanning calorimetry revealed high thermal stability (initial degradation temperature = 222.50 °C and glass transition temperature = 84.45°C) of LNC. Moreover, the obtained LNC fibers were crystalline (crystallinity index = 52.76 %). Their activation energy (124.95 kJ/mol) was determined using the Coats-Redfern method by employing eight solid-state diffusion models. Overall, this study motivates the use of ILs as green solvents to produce lignocellulose derivatives that are suitable for various applications.
Collapse
Affiliation(s)
- Mohsin Raza
- Chemical and Petroleum Engineering Department, College of Engineering, United Arab Emirates University, PO BOX 15551, Al Ain, United Arab Emirates
| | - Mohammad Jawaid
- Chemical and Petroleum Engineering Department, College of Engineering, United Arab Emirates University, PO BOX 15551, Al Ain, United Arab Emirates
| | - Basim Abu-Jdayil
- Chemical and Petroleum Engineering Department, College of Engineering, United Arab Emirates University, PO BOX 15551, Al Ain, United Arab Emirates.
| |
Collapse
|
5
|
Shah SV, Lamba BY, Tiwari AK, Sharma R. Self-flocculation behaviour of cellulose-based bioflocculant synthesized from sewage water grown Chlorella sorokiniana and Scenedesmus abundans. Bioprocess Biosyst Eng 2024; 47:725-736. [PMID: 38582779 DOI: 10.1007/s00449-024-03009-0] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/15/2023] [Accepted: 03/25/2024] [Indexed: 04/08/2024]
Abstract
The global energy crisis has spurred a shift from conventional to clean and sustainable energy sources. Biomass derived from microalgae is emerging as an alternative energy source with diverse applications. Despite the numerous advantages of microalgae, large-scale biomass harvesting is not economical and convenient. Self-flocculation is considered an effective phenomenon facilitated by extracting the flocculating substances from microalgae that assist aggregation of algal cells into flocs. A novel cellulose-based bioflocculant has been synthesized from sewage water grown Chlorella sorokiniana and Scenedesmus abundans for harvesting application. The produced bioflocculant amounted to 38.5% and 19.38% of the dry weight of S. abundans and C. sorokiniana, respectively. Analysis via FTIR, XRD, and FESEM-EDX revealed the presence of cellulose hydroxyapatite (HA) in algae-derived cellulose. Harvesting efficiencies of 95.3% and 89.16% were attained for S. abundans and C. sorokiniana, respectively, at a dosage of 0.5 g/L. Furthermore, the bioflocculant was recovered, enabling its reuse with recovery efficiencies of 52% and 10% for S. abundans and C. sorokiniana, respectively. This simple and efficient approach has the potential to replace other harvesting methods, thereby contributing to the economic algal biofuel production.
Collapse
Affiliation(s)
- Sonal Vilas Shah
- School of Advanced Engineering, UPES, Dehradun, Uttarakhand, India
- Centre for Alternate Energy Research (CAER), UPES, Dehradun, Uttarakhand, India
| | - Bhawna Yadav Lamba
- School of Advanced Engineering, UPES, Dehradun, Uttarakhand, India.
- Centre for Alternate Energy Research (CAER), UPES, Dehradun, Uttarakhand, India.
| | - Avanish K Tiwari
- Centre for Renewable Energy and Sustainable Development, VIKALP (Nai Dishayen), New Delhi, India
| | - Rohit Sharma
- University Institute of Engineering, Chandigarh University, Mohali, India
| |
Collapse
|
6
|
Sreedharan M, Vijayamma R, Liyaskina E, Revin VV, Ullah MW, Shi Z, Yang G, Grohens Y, Kalarikkal N, Ali Khan K, Thomas S. Nanocellulose-Based Hybrid Scaffolds for Skin and Bone Tissue Engineering: A 10-Year Overview. Biomacromolecules 2024; 25:2136-2155. [PMID: 38448083 DOI: 10.1021/acs.biomac.3c00975] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 03/08/2024]
Abstract
Cellulose, the most abundant polymer on Earth, has been widely utilized in its nanoform due to its excellent properties, finding applications across various scientific fields. As the demand for nanocellulose continues to rise and its ease of use becomes apparent, there has been a significant increase in research publications centered on this biomaterial. Nanocellulose, in its different forms, has shown tremendous promise as a tissue engineered scaffold for regeneration and repair. Particularly, nanocellulose-based composites and scaffolds have emerged as highly demanding materials for both soft and hard tissue engineering. Medical practitioners have traditionally relied on collagen and its analogue, gelatin, for treating tissue damage. However, the limited mechanical strength of these biopolymers restricts their direct use in various applications. This issue can be overcome by making hybrids of these biopolymers with nanocellulose. This review presents a comprehensive analysis of the recent and most relevant publications focusing on hybrid composites of collagen and gelatin with a specific emphasis on their combination with nanocellulose. While bone and skin tissue engineering represents two areas where a majority of researchers are concentrating their efforts, this review highlights the use of nanocellulose-based hybrids in these contexts.
Collapse
Affiliation(s)
- Mridula Sreedharan
- International and Inter University Centre for Nanoscience and Nanotechnology, Mahatma Gandhi University, Kottayam, Kerala 686560, India
| | - Raji Vijayamma
- International and Inter University Centre for Nanoscience and Nanotechnology, Mahatma Gandhi University, Kottayam, Kerala 686560, India
- School of Nanoscience and Nanotechnology, Mahatma Gandhi University, Kottayam, Kerala 686560, India
| | - Elena Liyaskina
- Department of Biotechnology, Biochemistry and Bioengineering, National Research Ogarev Mordovia State University, Saransk 430005, Russia
| | - Viktor V Revin
- Department of Biotechnology, Biochemistry and Bioengineering, National Research Ogarev Mordovia State University, Saransk 430005, Russia
| | - Muhammad Wajid Ullah
- Biofuels Institute, School of the Environment and Safety Engineering, Jiangsu University, Zhenjiang 212013, China
| | - Zhijun Shi
- Department of Biomedical Engineering, College of Life Science and Technology, Huazhong University of Science and Technology, Wuhan 430074, China
| | - Guang Yang
- Department of Biomedical Engineering, College of Life Science and Technology, Huazhong University of Science and Technology, Wuhan 430074, China
| | - Yves Grohens
- Univ. Bretagne Sud, UMR CNRS 6027, IRDL, F-56321 Lorient, France
| | - Nandakumar Kalarikkal
- International and Inter University Centre for Nanoscience and Nanotechnology, Mahatma Gandhi University, Kottayam, Kerala 686560, India
- School of Nanoscience and Nanotechnology, Mahatma Gandhi University, Kottayam, Kerala 686560, India
- School of Pure and Applied Physics, Mahatma Gandhi University, Kottayam, Kerala 686560, India
| | - Khalid Ali Khan
- Applied College, Mahala Campus and the Unit of Bee Research and Honey Production/Research Center for Advanced Materials Science (RCAMS), King Khalid University, Abha 61413, Saudi Arabia
| | - Sabu Thomas
- International and Inter University Centre for Nanoscience and Nanotechnology, Mahatma Gandhi University, Kottayam, Kerala 686560, India
- School of Nanoscience and Nanotechnology, Mahatma Gandhi University, Kottayam, Kerala 686560, India
- School of Energy Materials, Mahatma Gandhi University, Kottayam, Kerala 686560, India
| |
Collapse
|
7
|
Kim H, Dutta SD, Randhawa A, Patil TV, Ganguly K, Acharya R, Lee J, Park H, Lim KT. Recent advances and biomedical application of 3D printed nanocellulose-based adhesive hydrogels: A review. Int J Biol Macromol 2024; 264:130732. [PMID: 38479658 DOI: 10.1016/j.ijbiomac.2024.130732] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/15/2023] [Revised: 03/04/2024] [Accepted: 03/06/2024] [Indexed: 03/17/2024]
Abstract
Nanocellulose-based tissue adhesives show promise for achieving rapid hemostasis and effective wound healing. Conventional methods, such as sutures and staples, have limitations, prompting the exploration of bioadhesives for direct wound adhesion and minimal tissue damage. Nanocellulose, a hydrolysis product of cellulose, exhibits superior biocompatibility and multifunctional properties, gaining interest as a base material for bioadhesive development. This study explores the potential of nanocellulose-based adhesives for hemostasis and wound healing using 3D printing techniques. Nanocellulose enables the creation of biodegradable adhesives with minimal adverse effects and opens avenues for advanced wound healing and complex tissue regeneration, such as skin, blood vessels, lungs, cartilage, and muscle. This study reviews recent trends in various nanocellulose-based 3D printed hydrogel patches for tissue engineering applications. The review also introduces various types of nanocellulose and their synthesis, surface modification, and bioadhesive fabrication techniques via 3D printing for smart wound healing.
Collapse
Affiliation(s)
- Hojin Kim
- Department of Biosystems Engineering, Kangwon University, Chuncheon 24341, Gangwon-do, Republic of Korea; Interdisciplinary Program in Smart Agriculture, Kangwon National University, Chuncheon 24341, Gangwon-do, Republic of Korea
| | - Sayan Deb Dutta
- Department of Biosystems Engineering, Kangwon University, Chuncheon 24341, Gangwon-do, Republic of Korea; Institute of Forest Science, Kangwon National University, Chuncheon 24341, Gangwon-do, Republic of Korea
| | - Aayushi Randhawa
- Department of Biosystems Engineering, Kangwon University, Chuncheon 24341, Gangwon-do, Republic of Korea; Interdisciplinary Program in Smart Agriculture, Kangwon National University, Chuncheon 24341, Gangwon-do, Republic of Korea
| | - Tejal V Patil
- Department of Biosystems Engineering, Kangwon University, Chuncheon 24341, Gangwon-do, Republic of Korea; Interdisciplinary Program in Smart Agriculture, Kangwon National University, Chuncheon 24341, Gangwon-do, Republic of Korea
| | - Keya Ganguly
- Department of Biosystems Engineering, Kangwon University, Chuncheon 24341, Gangwon-do, Republic of Korea
| | - Rumi Acharya
- Department of Biosystems Engineering, Kangwon University, Chuncheon 24341, Gangwon-do, Republic of Korea; Interdisciplinary Program in Smart Agriculture, Kangwon National University, Chuncheon 24341, Gangwon-do, Republic of Korea
| | - Jieun Lee
- Department of Biosystems Engineering, Kangwon University, Chuncheon 24341, Gangwon-do, Republic of Korea; Interdisciplinary Program in Smart Agriculture, Kangwon National University, Chuncheon 24341, Gangwon-do, Republic of Korea
| | - Hyeonseo Park
- Department of Biosystems Engineering, Kangwon University, Chuncheon 24341, Gangwon-do, Republic of Korea; Interdisciplinary Program in Smart Agriculture, Kangwon National University, Chuncheon 24341, Gangwon-do, Republic of Korea
| | - Ki-Taek Lim
- Department of Biosystems Engineering, Kangwon University, Chuncheon 24341, Gangwon-do, Republic of Korea; Interdisciplinary Program in Smart Agriculture, Kangwon National University, Chuncheon 24341, Gangwon-do, Republic of Korea; Institute of Forest Science, Kangwon National University, Chuncheon 24341, Gangwon-do, Republic of Korea.
| |
Collapse
|
8
|
Norfarhana A, Ilyas R, Ngadi N, Dzarfan Othman MH. Innovative ionic liquid pretreatment followed by wet disk milling treatment provides enhanced properties of sugar palm nano-fibrillated cellulose. Heliyon 2024; 10:e27715. [PMID: 38509963 PMCID: PMC10951586 DOI: 10.1016/j.heliyon.2024.e27715] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/10/2023] [Revised: 03/05/2024] [Accepted: 03/05/2024] [Indexed: 03/22/2024] Open
Abstract
In order to accommodate the increased demand for innovative materials, intensive research has focused on natural resources. In pursuit of advanced substances that exhibit functionality, sustainability, recyclability, and cost-effectiveness, the present work attempted an alternative study on cellulose nanofibers derived from sugar palm fiber. Leveraging an innovative approach involving ionic liquid (IL) pre-treatment, bleaching, and wet disc mill technique, nano-fibrillated cellulose (NFC) was successfully obtained from the sugar palm fiber source. Remarkably, 96.89% of nanofibers were extracted from the sugar palm fiber, demonstrating the process's efficacy and scalability. Further investigation revealed that the sugar palm nano-fibrillated cellulose (SPNFC) exhibited a surface area of 3.46 m2/g, indicating a significant interface for enhanced functionality. Additionally, the analysis unveiled an average pore size of 4.47 nm, affirming its suitability for various applications that necessitate precise filtration. Moreover, the surface charge densities of SPNFC were found to be -32.1 mV, offering opportunities for surface modification and enhanced interactions with various materials. The SPNFC exhibit remarkable thermal stability, enduring temperatures of up to 360.5 °C. Additionally, the isolation process is evident in a significant rise in the crystallinity index, escalating from 50.97% in raw fibers to 61.62% in SPNFC. These findings shed light on the vast potential and distinct features of SPNFC, opening the path for its application in a wide array of industries, including but not limited to advanced materials, biomedicine, and environmental engineering.
Collapse
Affiliation(s)
- A.S. Norfarhana
- Department of Chemical Engineering, Faculty of Chemical and Energy Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor, Malaysia
- Department of Petrochemical Engineering, Politeknik Tun Syed Nasir Syed Ismail, Pagoh Education Hub, 84600 Pagoh Muar Johor, Malaysia
| | - R.A. Ilyas
- Department of Chemical Engineering, Faculty of Chemical and Energy Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor, Malaysia
- Centre for Advanced Composite Materials (CACM), Universiti Teknologi Malaysia (UTM), Johor Bahru 81310, Johor, Malaysia
- Institute of Tropical Forestry and Forest Products (INTROP), Universiti Putra Malaysia, Serdang 43400, Selangor, Malaysia
- Centre of Excellence for Biomass Utilization, Universiti Malaysia Perlis, 02600, Arau, Perlis, Malaysia
| | - Norzita Ngadi
- Department of Chemical Engineering, Faculty of Chemical and Energy Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor, Malaysia
| | - Mohd Hafiz Dzarfan Othman
- Department of Chemical Engineering, Faculty of Chemical and Energy Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor, Malaysia
- Advanced Membrane Technology Research Centre (AMTEC), Faculty of Chemical and Energy Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor, Malaysia
| |
Collapse
|
9
|
Kim M, Doh H. Upcycling Food By-products: Characteristics and Applications of Nanocellulose. Chem Asian J 2024:e202301068. [PMID: 38246883 DOI: 10.1002/asia.202301068] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/11/2023] [Revised: 01/16/2024] [Accepted: 01/17/2024] [Indexed: 01/23/2024]
Abstract
Rising global food prices and the increasing prevalence of food insecurity highlight the imprudence of food waste and the inefficiencies of the current food system. Upcycling food by-products holds significant potential for mitigating food loss and waste within the food supply chain. Food by-products can be utilized to extract nanocellulose, a material that has obtained substantial attention recently due to its renewability, biocompatibility, bioavailability, and a multitude of remarkable properties. Cellulose nanomaterials have been the subject of extensive research and have shown promise across a wide array of applications, including the food industry. Notably, nanocellulose possesses unique attributes such as a surface area, aspect ratio, rheological behavior, water absorption capabilities, crystallinity, surface modification, as well as low possibilities of cytotoxicity and genotoxicity. These qualities make nanocellulose suitable for diverse applications spanning the realms of food production, biomedicine, packaging, and beyond. This review aims to provide an overview of the outcomes and potential applications of cellulose nanomaterials derived from food by-products. Nanocellulose can be produced through both top-down and bottom-up approaches, yielding various types of nanocellulose. Each of these variants possesses distinctive characteristics that have the potential to significantly enhance multiple sectors within the commercial market.
Collapse
Affiliation(s)
- Mikyung Kim
- Department of Food Science and Biotechnology, Ewha Womans University, Seodaemun-gu, Seoul 03760, Republic of Korea
- Ewha Womans University, 52, Ewhayeodae-gil, Seodaemun-gu, Seoul, Republic of Korea, 03710
| | - Hansol Doh
- Department of Food Science and Biotechnology, Ewha Womans University, Seodaemun-gu, Seoul 03760, Republic of Korea
- Ewha Womans University, 52, Ewhayeodae-gil, Seodaemun-gu, Seoul, Republic of Korea, 03710
| |
Collapse
|
10
|
Cherian RM, Varghese RT, Antony T, Malhotra A, Kargarzadeh H, Chauhan SR, Chauhan A, Chirayil CJ, Thomas S. Non-cytotoxic, highly functionalized cellulose nanocrystals with high crystallinity and thermal stability derived from a novel agromass of Elettaria cardamomum, using a soft and benign mild oxalic acid hydrolysis. Int J Biol Macromol 2023; 253:126571. [PMID: 37648134 DOI: 10.1016/j.ijbiomac.2023.126571] [Citation(s) in RCA: 1] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/15/2023] [Revised: 08/22/2023] [Accepted: 08/26/2023] [Indexed: 09/01/2023]
Abstract
Non-cytotoxic, highly crystalline, and functionalized, thermally stable cellulose nanocrystals are extracted from the stems of Elettaria cardamom, a novel underutilised agromass, by employing a neat green, mild oxalic acid hydrolysis. The protocol involves a chemo-mechanical strategy of coupling hydrolysis with steam explosion and homogenization. The obtained CNC showed a crystallinity index of 81.51 %, an aspect ratio of 17.80 ± 1.03 and a high degradation temperature of about 339.07 °C. The extraction procedure imparted a high negative surface functionalization with a zeta potential value of -34.244 ± 0.496 mV and a polydispersity of 16.5 %. The CNC had no antibacterial activity, according to non-cytotoxic experiments conducted on four bacterial strains. This supports the notion of "One Health" in the context of AMR by demonstrating the safety of antibiotic resistance due to consistent exposure upon environmental disposal. The as-extracted nanocellulose crystals can be a potential candidate for commercial application in wide and diversified disciplines like food packaging, anti-infective surfaces for medical devices, biosensors, bioelectronics etc.
Collapse
Affiliation(s)
- Reeba Mary Cherian
- Department of Chemistry, Newman College, Thodupuzha, Kerala 685584, India; School of Chemical Sciences, Mahatma Gandhi University, Kottayam, Kerala 686560, India.
| | - Rini Thresia Varghese
- Department of Chemistry, Newman College, Thodupuzha, Kerala 685584, India; School of Chemical Sciences, Mahatma Gandhi University, Kottayam, Kerala 686560, India; Centre of Molecular and Macromolecular Studies, Polish Academy of Sciences, Sienkiewicza 112, 90-363 Lodz, Poland
| | - Tijo Antony
- Department of Chemistry, Newman College, Thodupuzha, Kerala 685584, India; School of Chemical Sciences, Mahatma Gandhi University, Kottayam, Kerala 686560, India; Department of Chemistry, Pavanatma College, Murickassery, Idukki, Kerala 685604, India
| | - Akshit Malhotra
- Department of Microbiology, University of Delhi- South campus, Delhi 110021, India
| | - Hanieh Kargarzadeh
- Centre of Molecular and Macromolecular Studies, Polish Academy of Sciences, Sienkiewicza 112, 90-363 Lodz, Poland
| | - Suchitra Rajput Chauhan
- Centre for Advanced Materials and Devices (CAMD), School of Engineering and Technology, BML Munjal University, Sidhrawali, Gurgaon, Haryana 122413, India
| | - Ashwini Chauhan
- Department of Microbiology, University of Delhi- South campus, Delhi 110021, India
| | | | - Sabu Thomas
- School of Chemical Sciences, Mahatma Gandhi University, Kottayam, Kerala 686560, India; School of Energy Materials, Mahatma Gandhi University, Kottayam, Kerala 686560, India; Department of Chemical Sciences, University of Johannesburg, P.O. Box. 17011, Doornfontein, 2028 Johannesburg, South Africa.
| |
Collapse
|
11
|
Mahur BK, Ahuja A, Singh S, Maji PK, Rastogi VK. Different nanocellulose morphologies (cellulose nanofibers, nanocrystals and nanospheres) extracted from Sunn hemp (Crotalaria Juncea). Int J Biol Macromol 2023; 253:126657. [PMID: 37660858 DOI: 10.1016/j.ijbiomac.2023.126657] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/24/2023] [Revised: 08/25/2023] [Accepted: 08/31/2023] [Indexed: 09/05/2023]
Abstract
Nanocellulose of different morphologies was extracted from Sunn Hemp (Crotalaria Juncea) using acid hydrolysis. The work focused on two objectives: first, to valorize the Sunn Hemp fibers for nanocellulose (NC) production, and second, to study the effects of acid concentration on different morphologies of NC and their properties. The study extracted nanocellulose at five different concentrations of H2SO4: 16 %, 32 %, 48 %, 64 %, and 72 %. Obtained nanocellulose was characterized by Scanning Electron Microscopy (FE-SEM), Atomic Force Microscopy (AFM), Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD) and Thermogravimetric Analysis (TGA). AFM and FE-SEM confirmed the production of three different morphologies of nanocellulose. The NC-32 had a web-like structure typically observed for cellulose nanofibrils (CNF), whereas NC-48 and NC-64 were observed as cellulose nanocrystals (CNC) with rod-like and needle-like shapes, respectively, and NC-72 displayed spherical particles termed cellulose nanospheres (CNS). The total crystallinity index of NC was calculated using FTIR, and a similar trend of crystallinity was also observed from XRD analysis. NC-32 was obtained with the highest yield of 94.83 %, followed by 91.40 % and 81.70 % for NC-48 and NC-64, respectively, whereas NC-72 yielded the lowest yield of 12.03 %. NC-72 had the highest thermal stability among other NC morphologies.
Collapse
Affiliation(s)
- Bhupender Kumar Mahur
- Department of Paper Technology, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667, India
| | - Arihant Ahuja
- Department of Paper Technology, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667, India
| | - Shiva Singh
- Department of Polymer Science & Engineering, Indian Institute of Technology Roorkee, Saharanpur Campus, Saharanpur, 247001, UP, India
| | - Pradip K Maji
- Department of Polymer Science & Engineering, Indian Institute of Technology Roorkee, Saharanpur Campus, Saharanpur, 247001, UP, India
| | - Vibhore Kumar Rastogi
- Department of Paper Technology, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667, India.
| |
Collapse
|
12
|
Saberi Riseh R, Vatankhah M, Hassanisaadi M, Kennedy JF. Increasing the efficiency of agricultural fertilizers using cellulose nanofibrils: A review. Carbohydr Polym 2023; 321:121313. [PMID: 37739539 DOI: 10.1016/j.carbpol.2023.121313] [Citation(s) in RCA: 8] [Impact Index Per Article: 8.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/18/2023] [Revised: 07/26/2023] [Accepted: 08/16/2023] [Indexed: 09/24/2023]
Abstract
Developing new agricultural products, such as new fertilizers with high use efficiency and less negative impact on the environment, is required in sustainable agriculture. In this vein, controlled-release fertilizers (CRFs) have been designed to decrease nutrient waste and increase nutrients' availability to plants. Various CRFs have been developed based on petroleum-derived polymers with many advantages over conventional fertilizers. Although, their use is limited due to their adverse effects on the soil and environment. To overcome these issues, CRFs based on biopolymers represent a new generation of fertilizers developed by encapsulating nutrients with cellulose nanofibrils (CNFs). CNFs and the hydrogels based on CNFs have great potential to be applied as CRFs matrix as they are biodegradable, minimize environmental pollution, and exhibit a great controlled-release potential and water/nutrient retention capacity. In order to gain a better understanding of the potential benefits of these new fertilizers in agricultural systems, this review summarizes the recent advances in CNFs in CRFs, the coating methods, hydrogel preparation techniques, and their impact on plant growth and soil. By examining these factors in depth, a better understanding can be gained on how these novel fertilizers can help improve agricultural productivity and sustainability.
Collapse
Affiliation(s)
- Roohallah Saberi Riseh
- Departement of Plant Protection, Faculty of Agriculture, Vali-e-Asr University of Rafsanjan, Rafsanjan 7718897111, Iran.
| | - Masoumeh Vatankhah
- Departement of Plant Protection, Faculty of Agriculture, Vali-e-Asr University of Rafsanjan, Rafsanjan 7718897111, Iran
| | - Mohadeseh Hassanisaadi
- Departement of Plant Protection, Faculty of Agriculture, Vali-e-Asr University of Rafsanjan, Rafsanjan 7718897111, Iran
| | - John F Kennedy
- Chembiotech Laboratories Ltd, WR15 8FF Tenbury Wells, United Kingdom.
| |
Collapse
|
13
|
Khotsaeng N, Simchuer W, Imsombut T, Srihanam P. Effect of Glycerol Concentrations on the Characteristics of Cellulose Films from Cattail ( Typha angustifolia L.) Flowers. Polymers (Basel) 2023; 15:4535. [PMID: 38231905 PMCID: PMC10708089 DOI: 10.3390/polym15234535] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/21/2023] [Revised: 11/16/2023] [Accepted: 11/22/2023] [Indexed: 01/19/2024] Open
Abstract
Plastic waste has become a big problem for the environment globally. Biodegradable polymers are a potential replacement for plastics that can have a positive outcome both environmentally and economically. In this work, we used acid hydrolysis and alkaline treatment to extract cellulose fibers from cattails. The obtained cellulose was used as a substrate for the fabrication of cellulose film using a casting technique on plastic plates. Different concentrations of the plasticizer, glycerol, were used to prepare films for comparison, and its effects on the film's characteristics were observed. The morphology, chemical structure, and thermal stability of the cattail cellulose (CTC) films were studied using techniques such as scanning electron microscopy (SEM), attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), and thermogravimetric analysis (TGA), respectively. Measurements of transparency, moisture content (MC), water solubility (MS), and water contact angle (WCA) were also performed. Introducing glycerol into the films increased the transparency, MC, and WS values, as well as the gap width between film textures. However, it resulted in a decrease in the WCA of the films, showing that the hydrophilicity of the films is increased by the addition of glycerol. The interaction between the functional groups of cellulose and glycerol was established from the ATR-FTIR and XRD data. The obtained results indicated that glycerol affected the thermal stability and the degree of crystallinity of the produced films. Accordingly, the hydrophilicity of the cellulose film was increased by increasing the glycerol content; therefore, cattail cellulose films can be used as a biodegradable alternative to plastic in the future.
Collapse
Affiliation(s)
- Nuanchai Khotsaeng
- Faculty of Science and Health Technology, Kalasin University, Namon District, Kalasin 46230, Thailand;
| | - Wilaiwan Simchuer
- Faculty of Science and Technology, Loei Rajabhat University, Mueang District, Loei 42000, Thailand;
| | - Thanonchat Imsombut
- Department of Rubber and Polymer Technology, Faculty of Science and Technology, Rajabhat Mahasarakham University, Mueang District, Maha Sarakham 44000, Thailand;
| | - Prasong Srihanam
- Biodegradable Polymers Research Unit, Department of Chemistry, Centre of Excellence for Innovation in Chemistry, Faculty of Science, Mahasarakham University, Maha Sarakham 44150, Thailand
| |
Collapse
|
14
|
Hemida MH, Moustafa H, Mehanny S, Morsy M, Dufresne A, Abd EL Rahman EN, Ibrahim M. Cellulose nanocrystals from agricultural residues ( Eichhornia crassipes): Extraction and characterization. Heliyon 2023; 9:e16436. [PMID: 37292363 PMCID: PMC10245161 DOI: 10.1016/j.heliyon.2023.e16436] [Citation(s) in RCA: 3] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/27/2022] [Revised: 05/11/2023] [Accepted: 05/16/2023] [Indexed: 06/10/2023] Open
Abstract
Extraction of cellulose nanocrystals (CNCs) from agro-residues has received much attention, not only for their unique properties supporting a wide range of potential applications, but also their limited risk to global climate change. This research was conducted to assess Nile roses (Eichhornia crassipes) fibers as a natural biomass to extract CNCs through an acid hydrolysis approach. Nile roses fibers (NRFs) were initially subjected to alkaline (pulping) and bleaching pretreatments. Microcrystalline cellulose (MCC) was used as control in comparison to Nile rose based samples. All samples underwent acid hydrolysis process at a mild temperature (45 °C). The impact of extraction durations ranging from 5 to 30 min on the morphology structure and crystallinity index of the prepared CNCs was investigated. The prepared CNCs were subjected to various characterization techniques, namely: X-ray diffraction (XRD), FT-IR analysis, Transmission electron microscopy (TEM), and X-ray Photoelectron spectroscopy (XPS). The outcomes obtained by XRD showed that the crystallinity index increased as the duration of acid hydrolysis was prolonged up to 10 min, and then decreased, indicating optimal conditions for the dissolution of amorphous zones of cellulose before eroding the crystallized domains. These data were confirmed by FT-IR spectroscopy. However, a minor effect of hydrolysis duration on the degree of crystallinity was noticed for MCC based samples. TEM images illustrated that a spherical morphology of CNCs was formed as a result of 30 min acid hydrolysis, highlighting the optimal 20 min acid hydrolysis to obtain a fibrillar structure. The XPS study demonstrated that the main constituents of extracted CNCs were carbon and oxygen.
Collapse
Affiliation(s)
- Mohamed H. Hemida
- Agricultural Engineering Department, Faculty of Agriculture, Cairo University, Egypt
| | - Hesham Moustafa
- Department of Polymer Metrology & Technology, National Institute of Standards (NIS), Tersa Street, El Haram, P.O Box 136, Giza, 12211, Giza, Egypt
- Bioanalysis Laboratory, National Institute of Standards (NIS), Tersa Street, El Haram, P.O Box 136, Giza, 12211, Giza, Egypt
| | - Sherif Mehanny
- Department of Mechanical Design and Production, Faculty of Engineering, Cairo University, Egypt
| | - Mohamed Morsy
- Building Physics and Environment Institute, Housing and Building National Research Center (HBRC), Dokki, Giza, Egypt
- Nanotechnology Research Center (NTRC), The British University in Egypt (BUE), El Sherouk City, Suez Desert Road, Cairo, 11837, Egypt
| | - Alain Dufresne
- Université Grenoble Alpes, CNRS, Grenoble INP, LGP2, F-38000, Grenoble, France
| | - Eid N. Abd EL Rahman
- Agricultural Engineering Department, Faculty of Agriculture, Cairo University, Egypt
| | - M.M. Ibrahim
- Agricultural Engineering Department, Faculty of Agriculture, Cairo University, Egypt
| |
Collapse
|
15
|
Refate A, Mohamed Y, Mohamed M, Sobhy M, Samhy K, Khaled O, Eidaroos K, Batikh H, El-Kashif E, El-Khatib S, Mehanny S. Influence of electrospinning parameters on biopolymers nanofibers, with emphasis on cellulose & chitosan. Heliyon 2023; 9:e17051. [PMID: 37484420 PMCID: PMC10361112 DOI: 10.1016/j.heliyon.2023.e17051] [Citation(s) in RCA: 5] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/23/2022] [Revised: 06/02/2023] [Accepted: 06/06/2023] [Indexed: 07/25/2023] Open
Abstract
Background Electrospinning is an effective method for producing high-quality biopolymer nanofibers, such as cellulose and chitosan. Cellulose nanofibers have excellent mechanical properties and biocompatibility, making them a promising material for tissue engineering. Chitosan nanofibers are biodegradable, biocompatible, and antimicrobial, making them ideal for biomedical applications. The electrospinning parameters, including solution concentration, power supply voltage, orifice diameter, temperature, humidity, and flow rate, play a crucial role in determining the nanofiber diameter, morphology, and mechanical properties, as well as their suitability for various applications. Objective This systematic review aims to synthesize and evaluate the current evidence on the influence of electrospinning parameters on the production and properties of cellulose and chitosan nanofibers. Methods A comprehensive search of electronic databases was conducted to identify relevant studies. The inclusion criteria were studies that investigated the effect of electrospinning parameters on cellulose and chitosan nanofibers. Results It was found that for cellulose, the average fiber diameter increased with increasing each of solution concentration, power supply voltage, orifice diameter, temperature, and humidity. Contrary to tip - collector distance and some optimal points in temperature, where average fiber diameter decreased. For chitosan, the change in voltage and tip to collector distance did not alter the average fiber diameter except for some readings of voltage, which behaved differently. On the other hand, the average fiber diameter increased with increasing flow rate. Conclusion The review highlights the importance of considering electrospinning parameters in the production of high-quality biopolymer nanofibers and provides insights into the optimization of these parameters for specific applications. This review also highlights the need for further research to better understand the underlying mechanisms of electrospinning and to optimize the process to produce biopolymer nanofibers with improved properties.
Collapse
Affiliation(s)
- Abdallah Refate
- Mechanical Design & Production Dept., Faculty of Engineering, Cairo University, Giza, Egypt
| | - Yehia Mohamed
- Mechatronics Program, Faculty of Engineering, Cairo University, Giza, Egypt
| | - Mariam Mohamed
- Electronics and Communication Dept., Faculty of Engineering, Cairo University, Giza, Egypt
| | - Maiada Sobhy
- Mechanical Design & Production Dept., Faculty of Engineering, Cairo University, Giza, Egypt
| | - Karim Samhy
- Mechanical Design & Production Dept., Faculty of Engineering, Cairo University, Giza, Egypt
| | - Omar Khaled
- Mechanical Design & Production Dept., Faculty of Engineering, Cairo University, Giza, Egypt
| | - Khaled Eidaroos
- Mechanical Design & Production Dept., Faculty of Engineering, Cairo University, Giza, Egypt
| | - Hazem Batikh
- Mechanical Design & Production Dept., Faculty of Engineering, Cairo University, Giza, Egypt
| | - Emad El-Kashif
- Mechanical Design & Production Dept., Faculty of Engineering, Cairo University, Giza, Egypt
| | - Samah El-Khatib
- Mechanical Engineering Dept., Faculty of Engineering & Technology, Future University in Egypt, 11835 Cairo, Egypt
| | - Sherif Mehanny
- Mechanical Design & Production Dept., Faculty of Engineering, Cairo University, Giza, Egypt
| |
Collapse
|
16
|
Andanje MN, Mwangi JW, Mose BR, Carrara S. Biocompatible and Biodegradable 3D Printing from Bioplastics: A Review. Polymers (Basel) 2023; 15:polym15102355. [PMID: 37242930 DOI: 10.3390/polym15102355] [Citation(s) in RCA: 4] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/17/2023] [Revised: 05/05/2023] [Accepted: 05/06/2023] [Indexed: 05/28/2023] Open
Abstract
There has been a lot of interest in developing and producing biodegradable polymers to address the current environmental problem caused by the continued usage of synthetic polymers derived from petroleum products. Bioplastics have been identified as a possible alternative to the use of conventional plastics since they are biodegradable and/or derived from renewable resources. Additive manufacturing, also referred to as 3D printing, is a field of growing interest and can contribute towards a sustainable and circular economy. The manufacturing technology also provides a wide material selection with design flexibility increasing its usage in the manufacture of parts from bioplastics. With this material flexibility, efforts have been directed towards developing 3D printing filaments from bioplastics such as Poly (lactic acid) to substitute the common fossil- based conventional plastic filaments such as Acrylonitrile butadiene styrene. Plant biomass is now utilized in the development of biocomposite materials. A lot of literature presents work done toward improving the biodegradability of printing filaments. However, additive manufacture of biocomposites from plant biomass is faced with printing challenges such as warping, low agglomeration between layers and poor mechanical properties of the printed parts. The aim of this paper is to review the technology of 3D printing using bioplastics, study the materials that have been utilized in this technology and how challenges of working with biocomposites in additive manufacture have been addressed.
Collapse
Affiliation(s)
- Maurine Naliaka Andanje
- Department of Mechatronic Engineering, Jomo Kenyatta University of Agriculture and Technology (JKUAT), Nairobi 00200, Kenya
| | - James Wamai Mwangi
- Department of Mechatronic Engineering, Jomo Kenyatta University of Agriculture and Technology (JKUAT), Nairobi 00200, Kenya
| | - Bruno Roberts Mose
- Department of Mechanical Engineering, Jomo Kenyatta University of Agriculture and Technology (JKUAT), Nairobi 00200, Kenya
| | - Sandro Carrara
- Institute of Electrical and Micro Engineering, École Polytechnique Fédérale de Lausanne (EPFL), 1015 Lausanne, Switzerland
| |
Collapse
|
17
|
Saud A, Saleem H, Khan AW, Munira N, Khan M, Zaidi SJ. Date Palm Tree Leaf-Derived Cellulose Nanocrystal Incorporated Thin-Film Composite forward Osmosis Membranes for Produced Water Treatment. MEMBRANES 2023; 13:membranes13050513. [PMID: 37233574 DOI: 10.3390/membranes13050513] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/13/2023] [Revised: 05/02/2023] [Accepted: 05/09/2023] [Indexed: 05/27/2023]
Abstract
Worldwide water shortage and significant issues related to treatment of wastewater streams, mainly the water obtained during the recovery of oil and gas operations called produced water (PW), has enabled forward osmosis (FO) to progress and become advanced enough to effectively treat as well as retrieve water in order to be productively reused. Because of their exceptional permeability qualities, thin-film composite (TFC) membranes have gained increasing interest for use in FO separation processes. This research focused on developing a high water flux and less oil flux TFC membrane by incorporating sustainably developed cellulose nanocrystal (CNC) onto the polyamide (PA) layer of the TFC membrane. CNCs are prepared from date palm leaves and different characterization studies verified the definite formations of CNCs and the effective integration of CNCs in the PA layer. From the FO experiments, it was confirmed that that the membrane with 0.05 wt% of CNCs in the TFC membrane (TFN-5) showed better FO performance in PW treatment. Pristine TFC and TFN-5 membrane exhibited 96.2% and 99.0% of salt rejection and 90.5% and 97.45% of oil rejection. Further, TFC and TFN-5 demonstrated 0.46 and 1.61 LMHB pure water permeability and 0.41 and 1.42 LHM salt permeability, respectively. Thus, the developed membrane can help in overcoming the current challenges associated with TFC FO membranes for PW treatment processes.
Collapse
Affiliation(s)
- Asif Saud
- Center for Advanced Material, Qatar University, Doha 2713, Qatar
| | - Haleema Saleem
- Center for Advanced Material, Qatar University, Doha 2713, Qatar
| | | | - Nazmin Munira
- Center for Advanced Material, Qatar University, Doha 2713, Qatar
| | - Maryam Khan
- Center for Advanced Material, Qatar University, Doha 2713, Qatar
| | | |
Collapse
|
18
|
Li J, Yang F, Liu D, Han S, Li J, Sui G. Graphene composite paper synergized with micro/nanocellulose-fiber and silk fibroin for flexible strain sensor. Int J Biol Macromol 2023; 240:124439. [PMID: 37062378 DOI: 10.1016/j.ijbiomac.2023.124439] [Citation(s) in RCA: 2] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/29/2022] [Revised: 03/22/2023] [Accepted: 04/10/2023] [Indexed: 04/18/2023]
Abstract
The fabrication of uniform and strong graphene-based conductive paper is challenging due to easy aggregation and poor film formability of graphene. Herein, on the basis of good dispersing effect of nanocellulose, high content graphene (50 wt%) composite paper with micro/nanocellulose fibers and silk fibroin (SF) was manufactured via simple casting method. The synergistic effects of cellulose microfibers (CMFs), cellulose nanofibers (CNFs) and SF result in the paper with ideal combination of flexibility, electrical conductivity and mechanical strength, where CNFs, CMFs and SF act as dispersing and film forming for GNPs, dimensional stability, and interfacial binding agents, respectively. Extraordinarily, by adding SF, graphene nanosheets are tightly coated on the surface of CMFs. The composite paper shows a tensile strength of 49.29 MPa, surface resistance of 39.0-42.1 Ω and good joints bend sensing performance. Additionally, it is found that CMFs can hinder the micro-cracks from propagating during the cyclic elbow bending test. The graphene-based conductive paper is helpful for the development of smart clothing wearable biosensing devices.
Collapse
Affiliation(s)
- Jun Li
- Shi-changxu Innovation Center for Advanced Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China; School of Materials Science and Engineering, University of Science and Technology of China, Shenyang 110016, China
| | - Fei Yang
- Shi-changxu Innovation Center for Advanced Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China; School of Materials Science and Engineering, University of Science and Technology of China, Shenyang 110016, China
| | - Dongyan Liu
- Shi-changxu Innovation Center for Advanced Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China.
| | - Sensen Han
- Shi-changxu Innovation Center for Advanced Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China; School of Materials Science and Engineering, University of Science and Technology of China, Shenyang 110016, China
| | - Junsheng Li
- Engineering Center of National New Raw Material Base Construction of Liaoning Province, Shenyang 110031, China
| | - Guoxin Sui
- Shi-changxu Innovation Center for Advanced Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China.
| |
Collapse
|
19
|
Sapuan SM, Harussani MM, Ismail AH, Zularifin Soh NS, Mohamad Azwardi MI, Siddiqui VU. Development of nanocellulose fiber reinforced starch biopolymer composites: a review. PHYSICAL SCIENCES REVIEWS 2023. [DOI: 10.1515/psr-2022-0007] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 03/22/2023]
Abstract
Abstract
In the last few years, there are rising numbers for environmental waste due to factors such as plastic based food packaging that really need to get enough attention in order to prevent the issue from becoming worse and bringing disaster to society. Thus, the uses of plastic composite materials need to be reduced and need to be replaced with materials that are natural and have low degradation to preserve nature. Based on the statistics for the global, the production of plastic has been roughly calculated for passing 400 million metric tons every year and has a high probability of approaching the value of 500 million metric tons at the year of 2025 and this issue needs to be counteracted as soon as possible. Due to that, the increasing number for recent development of natural biopolymer, as an example starch, has been investigated as the substitution for the non-biodegradable biopolymer. Besides, among all biodegradable polymers, starch has been considered as promising substitution polymer due to its renewability, easy availability, and biodegradability. Apart from that, by the reinforcement from the nanocellulose, starch fiber has an increasing in terms of mechanical, barrier and thermal properties. In this review paper, we will be discussing the up-to-date development of nanocellulose fiber reinforced starch biopolymer composites throughout this century.
Collapse
Affiliation(s)
- Salit Mohd Sapuan
- Department of Mechanical and Manufacturing Engineering , Advanced Engineering Materials and Composites (AEMC) Research Centre, Universiti Putra Malaysia (UPM) , Serdang , Selangor 43400 , Malaysia
| | - Moklis Muhammad Harussani
- Energy Science and Engineering, Department of Transdisciplinary Science and Engineering , School of Environment and Society, Tokyo Institute of Technology , Meguro 152-8552 , Tokyo , Japan
| | - Aleif Hakimi Ismail
- Department of Mechanical and Manufacturing Engineering , Advanced Engineering Materials and Composites (AEMC) Research Centre, Universiti Putra Malaysia (UPM) , Serdang , Selangor 43400 , Malaysia
| | - Noorashikin Soh Zularifin Soh
- Department of Mechanical and Manufacturing Engineering , Advanced Engineering Materials and Composites (AEMC) Research Centre, Universiti Putra Malaysia (UPM) , Serdang , Selangor 43400 , Malaysia
| | - Mohamad Irsyad Mohamad Azwardi
- Department of Mechanical and Manufacturing Engineering , Advanced Engineering Materials and Composites (AEMC) Research Centre, Universiti Putra Malaysia (UPM) , Serdang , Selangor 43400 , Malaysia
| | - Vasi Uddin Siddiqui
- Department of Mechanical and Manufacturing Engineering , Advanced Engineering Materials and Composites (AEMC) Research Centre, Universiti Putra Malaysia (UPM) , Serdang , Selangor 43400 , Malaysia
| |
Collapse
|
20
|
Trombino S, Sole R, Di Gioia ML, Procopio D, Curcio F, Cassano R. Green Chemistry Principles for Nano- and Micro-Sized Hydrogel Synthesis. Molecules 2023; 28:molecules28052107. [PMID: 36903352 PMCID: PMC10004334 DOI: 10.3390/molecules28052107] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/30/2022] [Revised: 01/26/2023] [Accepted: 01/26/2023] [Indexed: 03/06/2023] Open
Abstract
The growing demand for drug carriers and green-technology-based tissue engineering materials has enabled the fabrication of different types of micro- and nano-assemblies. Hydrogels are a type of material that have been extensively investigated in recent decades. Their physical and chemical properties, such as hydrophilicity, resemblance to living systems, swelling ability and modifiability, make them suitable to be exploited for many pharmaceutical and bioengineering applications. This review deals with a brief account of green-manufactured hydrogels, their characteristics, preparations, importance in the field of green biomedical technology and their future perspectives. Only hydrogels based on biopolymers, and primarily on polysaccharides, are considered. Particular attention is given to the processes of extracting such biopolymers from natural sources and the various emerging problems for their processing, such as solubility. Hydrogels are catalogued according to the main biopolymer on which they are based and, for each type, the chemical reactions and the processes that enable their assembly are identified. The economic and environmental sustainability of these processes are commented on. The possibility of large-scale processing in the production of the investigated hydrogels are framed in the context of an economy aimed at waste reduction and resource recycling.
Collapse
|
21
|
Shahzad A, Ullah MW, Ali J, Aziz K, Javed MA, Shi Z, Manan S, Ul-Islam M, Nazar M, Yang G. The versatility of nanocellulose, modification strategies, and its current progress in wastewater treatment and environmental remediation. THE SCIENCE OF THE TOTAL ENVIRONMENT 2023; 858:159937. [PMID: 36343829 DOI: 10.1016/j.scitotenv.2022.159937] [Citation(s) in RCA: 5] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 09/06/2022] [Revised: 10/27/2022] [Accepted: 10/31/2022] [Indexed: 06/16/2023]
Abstract
Deterioration in the environmental ecosystems through the depletion of nonrenewable resources and the burden of deleterious contaminants is considered a global concern. To this end, great interest has been shown in the use of renewable and environmentally-friendly reactive materials dually to promote environmental sustainability and cope with harmful contaminants. Among the different available options, the use of nanocellulose (NC) as an environmentally benign and renewable natural nanomaterial is an attractive candidate for environmental remediation owing to its miraculous physicochemical characteristics. This review discusses the intrinsic properties and the structural aspects of different types of NC, including cellulose nanofibrils (CNFs), cellulose nanocrystals (CNCs), and bacterial cellulose (BC) or bacterial nanocellulose (BNC). Also, the different modification strategies involving the functionalization or hybridization of NC by using different functional and reactive materials aimed at wastewater remediation have been elaborated. The modified or hybridized NC has been explored for its applications in the removal or degradation of aquatic contaminants through adsorption, filtration, coagulation, catalysis, photocatalysis, and pollutant sensing. This review highlights the role of NC in the modified composites and describes the underlying mechanisms involved in the removal of contaminants. The life-cycle assessment (LCA) of NC is discussed to unveil the hidden risks associated with its production to the final disposal. Moreover, the contribution of NC in the promotion of waste management at different stages has been described in the form of the five-Rs strategy. In summary, this review provides rational insights to develop NC-based environmentally-friendly reactive materials for the removal and degradation of hazardous aquatic contaminants.
Collapse
Affiliation(s)
- Ajmal Shahzad
- Department of Biomedical Engineering, College of Life Science and Technology, Huazhong University of Science and Technology, Wuhan 430074, PR China
| | - Muhammad Wajid Ullah
- Department of Biomedical Engineering, College of Life Science and Technology, Huazhong University of Science and Technology, Wuhan 430074, PR China; Biofuels Institute, School of the Environment and Safety Engineering, Jiangsu University, Zhenjiang 212013, PR China.
| | - Jawad Ali
- School of Environmental and Biological Engineering, Wuhan Technology and Business University, Wuhan 430065, PR China
| | - Kazim Aziz
- College of Earth and Environmental Sciences, University of the Punjab, Lahore, Pakistan
| | - Muhammad Asif Javed
- College of Earth and Environmental Sciences, University of the Punjab, Lahore, Pakistan
| | - Zhijun Shi
- Department of Biomedical Engineering, College of Life Science and Technology, Huazhong University of Science and Technology, Wuhan 430074, PR China
| | - Sehrish Manan
- Biofuels Institute, School of the Environment and Safety Engineering, Jiangsu University, Zhenjiang 212013, PR China
| | - Mazhar Ul-Islam
- Department of Chemical Engineering, College of Engineering, Dhofar University, Salalah 211, Oman
| | - Mudasir Nazar
- Biofuels Institute, School of the Environment and Safety Engineering, Jiangsu University, Zhenjiang 212013, PR China
| | - Guang Yang
- Department of Biomedical Engineering, College of Life Science and Technology, Huazhong University of Science and Technology, Wuhan 430074, PR China.
| |
Collapse
|
22
|
Valdés A, Mondragon G, Garrigós MC, Eceiza A, Jiménez A. Microwave-assisted extraction of cellulose nanocrystals from almond ( Prunus amygdalus) shell waste. Front Nutr 2023; 9:1071754. [PMID: 36761988 PMCID: PMC9902720 DOI: 10.3389/fnut.2022.1071754] [Citation(s) in RCA: 2] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/16/2022] [Accepted: 12/28/2022] [Indexed: 01/25/2023] Open
Abstract
Almond (Prunus amygdalus) is one of the most common tree nuts on a worldwide basis. This nut is highly regarded in the food and cosmetic industries. However, for all these applications, almonds are used without their shell protection, which is industrially removed contributing approximately 35-75% of the total fruit weight. This residue is normally incinerated or dumped, causing several environmental problems. In this study, a novel cellulose nanocrystal (CNCs) extraction procedure from almond shell (AS) waste by using microwave-assisted extraction was developed and compared with the conventional approach. A three-factor, three-level Box-Behnken design with five central points was used to evaluate the influence of extraction temperature, irradiation time, and NaOH concentration during the alkalization stage in crystallinity index (CI) values. A similar CI value (55.9 ± 0.7%) was obtained for the MAE process, comprising only three stages, compared with the conventional optimized procedure (55.5 ± 1.0%) with five stages. As a result, a greener and more environmentally friendly CNC extraction protocol was developed with a reduction in time, solvent, and energy consumption. Fourier transform infrared (FTIR) spectra, X-ray diffractogram (XRD), atomic force microscopy (AFM), and scanning electron microscopy (SEM) images, and thermal stability studies of samples confirmed the removal of non-cellulosic components after the chemical treatments. TEM images revealed a spherical shape of CNCs with an average size of 21 ± 6 nm, showing great potential to be used in food packaging, biological, medical, and photoelectric materials. This study successfully applied MAE for the extraction of spherical-shaped CNCs from AS with several advantages compared with the conventional procedure, reducing costs for industry.
Collapse
Affiliation(s)
- Arantzazu Valdés
- Department of Analytical Chemistry, Nutrition and Food Science, University of Alicante, San Vicente del Raspeig, Spain,*Correspondence: Arantzazu Valdés,
| | - Gurutz Mondragon
- Materials Technologies Group, Chemical and Environmental Engineering Department, University of the Basque Country - UPV/EHU, Donostia-San Sebastián, Spain
| | - María Carmen Garrigós
- Department of Analytical Chemistry, Nutrition and Food Science, University of Alicante, San Vicente del Raspeig, Spain
| | - Arantxa Eceiza
- Materials Technologies Group, Chemical and Environmental Engineering Department, University of the Basque Country - UPV/EHU, Donostia-San Sebastián, Spain
| | - Alfonso Jiménez
- Department of Analytical Chemistry, Nutrition and Food Science, University of Alicante, San Vicente del Raspeig, Spain
| |
Collapse
|
23
|
Raju V, Revathiswaran R, Subramanian KS, Parthiban KT, Chandrakumar K, Anoop EV, Chirayil CJ. Isolation and characterization of nanocellulose from selected hardwoods, viz., Eucalyptus tereticornis Sm. and Casuarina equisetifolia L., by steam explosion method. Sci Rep 2023; 13:1199. [PMID: 36681725 PMCID: PMC9867748 DOI: 10.1038/s41598-022-26600-5] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/28/2022] [Accepted: 12/16/2022] [Indexed: 01/22/2023] Open
Abstract
Extraction of nanocellulose is challenging, especially from hardwoods due to its complex chemical structure as well as structural hierarchy. In this study, nanocellulose was isolated from wood pulp of two hardwood species, namely Eucalyptus tereticornis Sm. and Casuarina equisetifolia L. by steam explosion process. Pure cellulose wood pulp was obtained through Kraft pulping process followed by alkaline and bleaching pre-treatments. Isolated nanocellulose was characterized by Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Atomic Force Microscopy (AFM), Fourier Transformed Infrared (FTIR) Spectra, Thermogravimetric Analysis (TGA), and X-ray diffraction (XRD) studies. Nanocellulose obtained from both species showed non-significant difference with average diameter of 27.801 nm for eucalyptus and 28.690 nm for casuarina, which was confirmed from TEM and AFM images. FTIR spectra of nanocellulose showed prominent peaks corresponding to cellulose and absence of peaks corresponding to lignin. The elemental purity of nanocellulose was confirmed with EDAX detector. XRD analysis showed the enrichment of crystalline cellulose in nanocellulose, and also confirmed the significant conversion of cellulose I to cellulose II. During TG analysis the untreated fibres started to degrade earlier than the nanocellulose which indicated the higher thermal stability of nanocellulose. Highly entangled network like structure along with high aspect ratio make the nanofibres a versatile material for reinforcing the composites. This successful method can be replicated for industrial level production of cellulose nanofibres.
Collapse
Affiliation(s)
- Vishnu Raju
- Forest College and Research Institute, Tamil Nadu Agricultural University, Mettupalayam, Tamil Nadu, 641301, India.
- Department of Forest Products and Utilization, College of Forestry, Kerala Agricultural University, Thrissur, Kerala, 680656, India.
| | - Revathi Revathiswaran
- Forest College and Research Institute, Tamil Nadu Agricultural University, Mettupalayam, Tamil Nadu, 641301, India
| | | | | | - Kalichamy Chandrakumar
- Department of Bioenergy, Tamil Nadu Agricultural University, Coimbatore, Tamil Nadu, 641003, India
| | - Elaveetil Vasu Anoop
- Department of Forest Products and Utilization, College of Forestry, Kerala Agricultural University, Thrissur, Kerala, 680656, India
| | | |
Collapse
|
24
|
Xie P, Ge Y, Wang Y, Zhou J, Miao Y, Liu Z. Mechanically Enhanced Nanocrystalline Cellulose/Reduced Graphene Oxide/Polyethylene Glycol Electrically Conductive Composite Film. NANOMATERIALS (BASEL, SWITZERLAND) 2022; 12:4371. [PMID: 36558225 PMCID: PMC9784714 DOI: 10.3390/nano12244371] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 11/15/2022] [Revised: 11/30/2022] [Accepted: 12/05/2022] [Indexed: 06/17/2023]
Abstract
Traditional conductive materials do not meet the increasing requirements of electronic products because of such materials' high rigidity, poor flexibility, and slow biodegradation after disposal. Preparing flexible conductive materials with excellent mechanical properties is an active area of research. The key to flexible conductive materials lies in the combination of the polymer matrix and conductive components. This combination can be achieved by making a film of renewable nano-microcrystalline cellulose (NCC) and reduced graphene oxide (rGO) with excellent electrical conductivity-by simple filtration and introducing polyethylene glycol (PEG) to enhance the functionality of the composite film. Graphene imparted conductivity to the composite film, which reached 5.67 S·m-1. A reinforced NCC/rGO/PEG-4 composite film with a thickness of only 21 μm exhibited a tensile strength of 30.56 MPa, which was 83% higher than that of the sample without PEG (16.71 MPa), and toughness of 727.18 kJ·m-3, which was about 132% higher than that of the control sample (NCC/rGO, 313.86 kJ·m-3). This ultra-thin conductive composite film-which can be prepared simply, consists of environmentally sustainable and biodegradable raw materials, and exhibits excellent mechanical properties-has substantial potential for applications in e.g., flexible electronic wearable devices, electrodes, and capacitors.
Collapse
Affiliation(s)
| | | | | | | | - Yuanyuan Miao
- Correspondence: (Y.M.); (Z.L.); Tel.: +86-13-(94)-5697965 (Z.L.)
| | - Zhenbo Liu
- Correspondence: (Y.M.); (Z.L.); Tel.: +86-13-(94)-5697965 (Z.L.)
| |
Collapse
|
25
|
Choque-Quispe D, Choque-Quispe Y, Ligarda-Samanez CA, Peralta-Guevara DE, Solano-Reynoso AM, Ramos-Pacheco BS, Taipe-Pardo F, Martínez-Huamán EL, Aguirre Landa JP, Agreda Cerna HW, Loayza-Céspedes JC, Zamalloa-Puma MM, Álvarez-López GJ, Zamalloa-Puma A, Moscoso-Moscoso E, Quispe-Quispe Y. Effect of the Addition of Corn Husk Cellulose Nanocrystals in the Development of a Novel Edible Film. NANOMATERIALS (BASEL, SWITZERLAND) 2022; 12:3421. [PMID: 36234547 PMCID: PMC9565820 DOI: 10.3390/nano12193421] [Citation(s) in RCA: 4] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 09/01/2022] [Revised: 09/26/2022] [Accepted: 09/26/2022] [Indexed: 06/16/2023]
Abstract
The cellulose from agroindustrial waste can be treated and converted into nanocrystals or nanofibers. It could be used to produce biodegradable and edible films, contributing to the circular economy and being environmentally friendly. This research aimed to develop an edible film elaborated with activated cellulose nanocrystals, native potato starch, and glycerin. The activated cellulose nanocrystals were obtained by basic/acid digestion and esterification with citric acid from corn husks. The starch was extracted from the native potato cultivated at 3500 m of altitude. Four film formulations were elaborated with potato starch (2.6 to 4.4%), cellulose nanocrystals (0.0 to 0.12%), and glycerin (3.0 to 4.2%), by thermoforming at 60 °C. It was observed that the cellulose nanocrystals reported an average size of 676.0 nm. The films mainly present hydroxyl, carbonyl, and carboxyl groups that stabilize the polymeric matrix. It was observed that the addition of cellulose nanocrystals in the films significantly increased (p-value < 0.05) water activity (0.409 to 0.447), whiteness index (96.92 to 97.27), and organic carbon content. In opposition to gelatinization temperature (156.7 to 150.1 °C), transparency (6.69 to 6.17), resistance to traction (22.29 to 14.33 N/mm), and solubility in acidic, basic, ethanol, and water media decreased. However, no significant differences were observed in the thermal decomposition of the films evaluated through TGA analysis. The addition of cellulose nanocrystals in the films gives it good mechanical and thermal resistance qualities, with low solubility, making it a potential food-coating material.
Collapse
Affiliation(s)
- David Choque-Quispe
- Water Analysis and Control Research Laboratory, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Department of Agroindustrial Engineering, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Research Group in the Development of Advanced Materials for Water and Food Treatment, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Nutraceuticals and Biopolymers Research Group, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
| | - Yudith Choque-Quispe
- Research Group in the Development of Advanced Materials for Water and Food Treatment, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Nutraceuticals and Biopolymers Research Group, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Department of Environmental Engineering, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
| | - Carlos A. Ligarda-Samanez
- Department of Agroindustrial Engineering, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Research Group in the Development of Advanced Materials for Water and Food Treatment, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Nutraceuticals and Biopolymers Research Group, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Food Nanotechnology Research Laboratory, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
| | - Diego E. Peralta-Guevara
- Water Analysis and Control Research Laboratory, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Research Group in the Development of Advanced Materials for Water and Food Treatment, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Nutraceuticals and Biopolymers Research Group, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Department of Environmental Engineering, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
| | - Aydeé M. Solano-Reynoso
- Research Group in the Development of Advanced Materials for Water and Food Treatment, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Nutraceuticals and Biopolymers Research Group, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Department of Environmental Engineering, Universidad Tecnológica de los Andes, Andahuaylas 03701, Peru
| | - Betsy S. Ramos-Pacheco
- Water Analysis and Control Research Laboratory, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Department of Agroindustrial Engineering, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Research Group in the Development of Advanced Materials for Water and Food Treatment, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Nutraceuticals and Biopolymers Research Group, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
| | - Fredy Taipe-Pardo
- Department of Agroindustrial Engineering, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Research Group in the Development of Advanced Materials for Water and Food Treatment, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Nutraceuticals and Biopolymers Research Group, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
| | - Edgar L. Martínez-Huamán
- Water Analysis and Control Research Laboratory, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Food Nanotechnology Research Laboratory, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Department of Education and Humanities, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
| | - John Peter Aguirre Landa
- Department of Business Administration, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
| | - Henrry W. Agreda Cerna
- Department of Business Administration, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
| | - Julio C. Loayza-Céspedes
- Departamento de Ingeniería Agropecuaria, Universidad Nacional de San Antonio Abad del Cusco, Andahuaylas 03701, Peru
| | | | | | - Alan Zamalloa-Puma
- Department of Physics, Universidad Nacional de San Antonio Abad del Cusco, Cusco 08000, Peru
| | - Elibet Moscoso-Moscoso
- Research Group in the Development of Advanced Materials for Water and Food Treatment, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Nutraceuticals and Biopolymers Research Group, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
- Food Nanotechnology Research Laboratory, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
| | - Yadyra Quispe-Quispe
- Research Group in the Development of Advanced Materials for Water and Food Treatment, Universidad Nacional José María Arguedas, Andahuaylas 03701, Peru
| |
Collapse
|
26
|
Isolation and Characterization Cellulose Nanosphere from Different Agricultural By-Products. Polymers (Basel) 2022; 14:polym14132534. [PMID: 35808579 PMCID: PMC9269051 DOI: 10.3390/polym14132534] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/28/2022] [Revised: 06/16/2022] [Accepted: 06/17/2022] [Indexed: 02/04/2023] Open
Abstract
Cellulose nanospheres (CN) have been considered a leading type of nanomaterial that can be applied as a strengthening material in the production of nanocomposites. This work aimed to isolate and characterize the properties of CN from different agricultural by-products. CNs were successfully isolated from rice straw, corncob, Phulae pineapple leaf and peel using acid hydrolysis (60% H2SO4) combined with homogenization-sonication (homogenized at 12,000 rpm for 6 min and ultrasonicated for 10 min). The results showed that the CN from rice straw (RS-CN) and corncob (CC-CN) exhibited high yields (22.27 and 22.36%) (p < 0.05). All hydrolyzed CNs exhibited a spherical shape with a diameter range of 2 to 127 nm. After acid hydrolysis, Fourier transform infrared (FTIR) results showed no impurities. X-ray diffraction (XRD) showed that the structure of cellulose was changed from cellulose-I to cellulose-II. However, cellulose-I remained in pineapple peel cellulose nanosphere (PP-CN). The crystalline index (CI) ranged from 43.98 to 73.58%, with the highest CI obtained in the CC-CN. The CN from all sources presented excellent thermal stability (above 300 °C). The functional properties, including water absorption Index (WAI), water solubility index (WSI) and swelling capacity were investigated. PP-CN showed the highest WAI and swelling capacity, while the PL-CN had the highest WSI (p < 0.05). Among all samples, CC-CN showed the highest extraction yield, small particle size, high CI, and desirable functional properties to be used as a material for bio-nanocomposites film.
Collapse
|
27
|
Recent Advances in 3D Bioprinting: A Review of Cellulose-Based Biomaterials Ink. Polymers (Basel) 2022; 14:polym14112260. [PMID: 35683932 PMCID: PMC9183181 DOI: 10.3390/polym14112260] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/18/2022] [Revised: 05/28/2022] [Accepted: 05/30/2022] [Indexed: 12/19/2022] Open
Abstract
Cellulose-based biodegradable hydrogel proves to be excellently suitable for the medical and water treatment industry based on the expressed properties such as its flexible structure and broad compatibility. Moreover, their potential to provide excellent waste management from the unutilized plant has triggered further study on the advanced biomaterial applications. To extend the use of cellulose-based hydrogel, additive manufacturing is a suitable technique for hydrogel fabrication in complex designs. Cellulose-based biomaterial ink used in 3D bioprinting can be further used for tissue engineering, drug delivery, protein study, microalgae, bacteria, and cell immobilization. This review includes a discussion on the techniques available for additive manufacturing, bio-based material, and the formation of a cellulose-based hydrogel.
Collapse
|
28
|
Romruen O, Karbowiak T, Tongdeesoontorn W, Shiekh KA, Rawdkuen S. Extraction and Characterization of Cellulose from Agricultural By-Products of Chiang Rai Province, Thailand. Polymers (Basel) 2022; 14:polym14091830. [PMID: 35566998 PMCID: PMC9099998 DOI: 10.3390/polym14091830] [Citation(s) in RCA: 8] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/24/2022] [Revised: 04/22/2022] [Accepted: 04/26/2022] [Indexed: 02/06/2023] Open
Abstract
Cellulose is an abundant component of the plant biomass in agricultural waste valorization that may be exploited to mitigate the excessive use of synthetic non-biodegradable materials. This work aimed to investigate the cellulose utilized by alkaline extraction with a prior bleaching process from rice straw, corncob, Phulae pineapple leaves, and Phulae pineapple peels. The bleaching and alkaline extraction process was performed using 1.4% acidified sodium chlorite (NaClO2) and 5% potassium hydroxide (KOH) in all the samples. All the samples, without and with the alkaline process, were characterized for their physico-chemical, microstructure, thermal properties and compared to commercial cellulose (COM-C). The extraction yield was the highest in alkaline-extracted cellulose from the corncob (AE-CCC) sample (p < 0.05), compared to the other alkaline-treated samples. The undesired components, including mineral, lignin, and hemicellulose, were lowest in the AE-CCC sample (p < 0.05), compared to raw and alkaline-treated samples. The microstructure displayed the flaky AE-CCC structure that showed a similar visibility in terms of morphology with that of the alkaline-treated pineapple peel cellulose (AE-PPC) and COM-C samples compared to other alkaline-treated samples with a fibrous structure. Fourier Transform Infrared (FTIR) and X-ray Diffraction (XRD) of AE-CCC samples showed the lowest amorphous regions, possibly due to the elimination of hemicellulose and lignin during bleaching and alkaline treatment. The highest crystallinity index obtained in the AE-CCC sample showed a close resemblance with the COM-C sample. Additionally, the AE-CCC sample showed the highest thermal stability, as evidenced by its higher Tonset (334.64 °C), and Tmax (364.67 °C) compared to the COM-C and alkaline-treated samples. Therefore, agricultural wastes after harvesting in the Chiang Rai province of Thailand may be subjected to an alkaline process with a prior bleaching process to yield a higher cellulose content that is free of impurities. Thus, the extracted cellulose could be used as an efficient, eco-friendly, and biodegradable material for packaging applications.
Collapse
Affiliation(s)
- Orapan Romruen
- Food Science and Technology Program, School of Agro-Industry, Mae Fah Luang University, Chiang Rai 57100, Thailand;
| | - Thomas Karbowiak
- UMR PAM-Food and Wine Science & Technology, Agro-Sup Dijon, Université de Bourgogne France-Comte, Esplanade Erasme, F-21000 Dijon, France;
| | - Wirongrong Tongdeesoontorn
- Unit of Innovative Food Packaging and Biomaterials, School of Agro-Industry, Mae Fah Luang University, Chiang Rai 57100, Thailand; (W.T.); (K.A.S.)
| | - Khursheed Ahmad Shiekh
- Unit of Innovative Food Packaging and Biomaterials, School of Agro-Industry, Mae Fah Luang University, Chiang Rai 57100, Thailand; (W.T.); (K.A.S.)
| | - Saroat Rawdkuen
- Food Science and Technology Program, School of Agro-Industry, Mae Fah Luang University, Chiang Rai 57100, Thailand;
- Unit of Innovative Food Packaging and Biomaterials, School of Agro-Industry, Mae Fah Luang University, Chiang Rai 57100, Thailand; (W.T.); (K.A.S.)
- Correspondence: ; Tel.: +66-53916739; Fax: +66-53916737
| |
Collapse
|
29
|
Tian W, Gao X, Zhang J, Yu J, Zhang J. Cellulose nanosphere: Preparation and applications of the novel nanocellulose. Carbohydr Polym 2022; 277:118863. [PMID: 34893268 DOI: 10.1016/j.carbpol.2021.118863] [Citation(s) in RCA: 17] [Impact Index Per Article: 8.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/06/2021] [Revised: 10/18/2021] [Accepted: 11/03/2021] [Indexed: 11/25/2022]
Abstract
Over the past few years, cellulose nanosphere (CNS) has gained growing attention and rapid development. As a new type of nanocellulose materials, CNS can be prepared from native cellulose by using methods which have been adopted extensively to prepare the well-known nanocelluloses, i.e., cellulose nanofiber and cellulose nanocrystal. The particular interest is that the regenerated cellulose and mercerized cellulose can also be used as important feedstocks to produce CNS. In this review, the preparation methods of CNS are described and discussed, via both top-down processes, including chemical, mechanical, and enzymolysis ones, and bottom-up processes by using various cellulose I and II starting materials. This review also highlights the researches relative to cellulose composite nanospheres, and summarizes the applications of spherical cellulose-based nanoparticles. Finally, the future challenges and opportunities of CNS are prospected in this work.
Collapse
Affiliation(s)
- Weiguo Tian
- Beijing National Laboratory for Molecular Sciences, CAS Key Laboratory of Engineering Plastics, Institute of Chemistry, Chinese Academy of Sciences (CAS), Beijing 100190, China
| | - Xuexin Gao
- Beijing National Laboratory for Molecular Sciences, CAS Key Laboratory of Engineering Plastics, Institute of Chemistry, Chinese Academy of Sciences (CAS), Beijing 100190, China; University of Chinese Academy of Sciences, Beijing 100049, China
| | - Jinming Zhang
- Beijing National Laboratory for Molecular Sciences, CAS Key Laboratory of Engineering Plastics, Institute of Chemistry, Chinese Academy of Sciences (CAS), Beijing 100190, China
| | - Jian Yu
- Beijing National Laboratory for Molecular Sciences, CAS Key Laboratory of Engineering Plastics, Institute of Chemistry, Chinese Academy of Sciences (CAS), Beijing 100190, China.
| | - Jun Zhang
- Beijing National Laboratory for Molecular Sciences, CAS Key Laboratory of Engineering Plastics, Institute of Chemistry, Chinese Academy of Sciences (CAS), Beijing 100190, China; University of Chinese Academy of Sciences, Beijing 100049, China.
| |
Collapse
|
30
|
Nanocrystalline Cellulose from Microcrystalline Cellulose of Date Palm Fibers as a Promising Candidate for Bio-Nanocomposites: Isolation and Characterization. MATERIALS 2021; 14:ma14185313. [PMID: 34576536 PMCID: PMC8472803 DOI: 10.3390/ma14185313] [Citation(s) in RCA: 8] [Impact Index Per Article: 2.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 07/20/2021] [Revised: 08/15/2021] [Accepted: 08/23/2021] [Indexed: 11/29/2022]
Abstract
Date palm fiber (Phoenix dactylifera L.) is a natural biopolymer rich in lignocellulosic components. Its high cellulose content lends them to the extraction of tiny particles like microcrystalline cellulose (MCC) and nanocrystalline cellulose (NCC). These cellulose-derived small size particles can be used as an alternative biomaterial in wide fields of application due to their renewability and sustainability. In the present work, NCC (A) and NCC (B) were isolated from date palm MCC at 60 min and 90 min hydrolysis times, respectively. The isolated NCC product was subjected to characterization to study their properties differences. With the hydrolysis treatment, the yields of produced NCC could be attained at between 22% and 25%. The infrared-ray functional analysis also revealed the isolated NCC possessed a highly exposed cellulose compartment with minimized lignoresidues of lignin and hemicellulose. From morphology evaluation, the nanoparticles’ size was decreased gradually from NCC (A) (7.51 nm width, 139.91 nm length) to NCC (B) (4.34 nm width, 111.51 nm length) as a result of fragmentation into cellulose fibrils. The crystallinity index was found increasing from NCC (A) to NCC (B). With 90 min hydrolysis time, NCC (B) showed the highest crystallinity index of 71% due to its great cellulose rigidity. For thermal analysis, NCC (B) also exhibited stable heat resistance, in associating with its highly crystalline cellulose structure. In conclusion, the NCC isolated from date palm MCC would be a promising biomaterial for various applications such as biomedical and food packaging applications.
Collapse
|
31
|
Current Status of Cellulosic and Nanocellulosic Materials for Oil Spill Cleanup. Polymers (Basel) 2021; 13:polym13162739. [PMID: 34451277 PMCID: PMC8400096 DOI: 10.3390/polym13162739] [Citation(s) in RCA: 12] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/18/2021] [Revised: 08/05/2021] [Accepted: 08/09/2021] [Indexed: 12/23/2022] Open
Abstract
Recent developments in the application of lignocellulosic materials for oil spill removal are discussed in this review article. The types of lignocellulosic substrate material and their different chemical and physical modification strategies and basic preparation techniques are presented. The morphological features and the related separation mechanisms of the materials are summarized. The material types were classified into 3D-materials such as hydrophobic and oleophobic sponges and aerogels, or 2D-materials such as membranes, fabrics, films, and meshes. It was found that, particularly for 3D-materials, there is a clear correlation between the material properties, mainly porosity and density, and their absorption performance. Furthermore, it was shown that nanocellulosic precursors are not exclusively suitable to achieve competitive porosity and therefore absorption performance, but also bulk cellulose materials. This finding could lead to developments in cost- and energy-efficient production processes of future lignocellulosic oil spillage removal materials.
Collapse
|
32
|
Spanish Poplar Biomass as a Precursor for Nanocellulose Extraction. APPLIED SCIENCES-BASEL 2021. [DOI: 10.3390/app11156863] [Citation(s) in RCA: 5] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/16/2022]
Abstract
The effect of acidic hydrolysis duration on nanocellulose size, morphology, and proper ties was investigated, which opens up a whole new horizon of versatility in poplar applications. This study aimed to examine Spanish poplar wastes as raw material to extract crystalline nanocellulose (CNC), which substantiates the importance of poplar wastes. Wastes were pulped using 1 L of 10% NaOH (wt./wt.) solution, and bleached several times by NaClO2; afterwards, white wastes were subjected to acidic hydrolysis by 60% H2SO4 for either 5, 10, or 15 min. Microcrystalline cellulose (MCC) underwent a similar hydrolysis protocol as poplar as control. TEM, IR, and XRD characterization techniques were performed. Poplar based nanocellulose sized 219 nm length and 69 nm width after 15 min acidic hydrolysis. MCC yielded 122 nm length and 12 nm width crystals after 10 min acidic hydrolysis. Hydrolysis resulted in a drastic change and intense peaks at 3500 and 2900 cm−1 for nanocellulose. Although pre-hydrolysis fiber treatment was not influencial on the crystallinity of poplar, acidic hydrolysis remarkably raised the crystallinity index (CI) by 7–8%. The more hydrolysis duration was prolonged, the size of the resulting crystal (whisker) decreased, and the aspect ratio increased. Hydrolysis was more impactful on MCC than poplar. However, for future work, it seems that longer duration of pulping and bleaching could have significantly removed unwanted components (hemicellulose and lignin), showcased in IR and XRD, and hence smoothened the following hydrolysis.
Collapse
|
33
|
Performance efficiency of MIPOH polymers as organic filler on cellulose pulp waste to form cellulosic paper sheets with biological evaluation and computational studies. Polym Bull (Berl) 2021. [DOI: 10.1007/s00289-021-03685-y] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/26/2022]
|
34
|
Liu S, Qamar SA, Qamar M, Basharat K, Bilal M. Engineered nanocellulose-based hydrogels for smart drug delivery applications. Int J Biol Macromol 2021; 181:275-290. [PMID: 33781811 DOI: 10.1016/j.ijbiomac.2021.03.147] [Citation(s) in RCA: 38] [Impact Index Per Article: 12.7] [Reference Citation Analysis] [Abstract] [Key Words] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/26/2020] [Revised: 03/21/2021] [Accepted: 03/23/2021] [Indexed: 12/26/2022]
Abstract
Nanocellulose is a promising "green" nanomaterial that has recently gained scientific interest because of its excellent characteristics, such as less risks of toxicity, biocompatibility, biodegradability, recyclability, and tunable surface features. Initially, three nanocellulose types (i.e., bacterial nanocellulose, nanocrystals, and nanofibers) and their potential biotechnological production routes have been discussed in detail. Contemporary studies are discussed in the development of nanocellulose aerogels, responsive hydrogels, injectable hydrogels/implants, and magnetic nanocellulose. Moreover, the development of hydrogels and potential crosslinking agents for the induction of desired properties has been described. Studies have revealed that the release kinetics of nanocellulosic gels/hydrogels varies from few minutes to several days depending on the given physicochemical conditions. However, such systems provide sustained drug release properties, so they are considered "smart" systems. Recent studies on controlled drug delivery systems have demonstrated their considerable potential for the next-generation transport of therapeutic drugs to target sites via various administration routes. This review presents the selection of appropriate sources and processing methodologies for the development of target nanocellulose types. It explains the potential challenges and opportunities and recommends future research directions about the smart delivery of therapeutic drugs.
Collapse
Affiliation(s)
- Shuai Liu
- School of Life Science and Food Engineering, Huaiyin Institute of Technology, Huaian 223003, China.
| | - Sarmad Ahmad Qamar
- Institute of Organic and Polymeric Materials, National Taipei University of Technology, Taipei 10608, Taiwan.
| | - Mahpara Qamar
- Department of Biochemistry, University of Agriculture, Faisalabad, Pakistan
| | - Kanta Basharat
- Department of Microbiology, University of Agriculture, Faisalabad, Pakistan
| | - Muhammad Bilal
- School of Life Science and Food Engineering, Huaiyin Institute of Technology, Huaian 223003, China.
| |
Collapse
|