Nanocellulose and its derived composite electrodes toward supercapacitors: Fabrication, properties, and challenges

High Capacitive Performance of N,O-Codoped Carbon Aerogels Synthesized via a One-Step Chemical Blowing and In Situ Activation Process

Biomass and its derivatives, with their renewable characteristics, cost-effectiveness, and controllable structural and compositional properties, are promising precursors for carbon materials. Herein, N,O-codoped carbon aerogels were synthesized by carbonization and zinc nitrate activation of histidine. The specific surface area (SSA) was markedly increased with the addition of zinc nitrate, and the maximum value achieved 853 m2 g-1 for ZHC-11 obtained with the molar ratio of 1:1 between histidine and zinc nitrate. The D/G-band intensity ratio increased from 1.55 for the histidine-derived control sample HC to 1.65 for ZHC-11, indicating the enhancement of amorphous feature. The nitrogen content increased from 6.5% for HC to 1.60 for ZHC-11. The optimized microstructure and enriched heteroatom doping are beneficial to the capacitance performance. The optimum electrode exhibited 234.1 F g-1 at 0.1 A g-1 and maintained 116.5 F g-1 at 60 A g-1 in a three-electrode system. In particular, the symmetric supercapacitor showed 121.9 F g-1 and 19.5 Wh kg-1 at 0.2 A g-1. This research offers guidance on the cost-effective synthesis of carbon materials for supercapacitors, while also providing novel insights to realize the complete utilization of biomass derivatives.

N/O Co-doped Porous Carbon with Controllable Porosity Synthesized via an All-in-One Step Method for a High-Rate-Performance Supercapacitor

A green and economical methodology to fabricate carbon-based materials with suitable pore size distributions is needed to achieve rapid electrolyte diffusion and improve the performance of supercapacitors. Here, a method combining in situ templates with self-activation and self-doping is proposed. By variation of the molar ratio of magnesium folate and potassium folate, the pore size distribution was effectively adjusted. The optimal carbon materials (Kx) have a high specific surface area (1021-1676 m2 g-1) and hierarchical pore structure, which significantly promotes its excellent capacitive properties. Notably, K2 shows an excellent mass specific capacitance of 233 F g-1 at 0.1 A g-1. It still retained 113 F g-1 at 55 A g-1. The assembled symmetric supercapacitor exhibited an outstanding cyclic stability. It maintains 100% capacitance after 100 000 cycles at 10 A g-1. The symmetric supercapacitor demonstrated a maximum power density of 99.8 kW kg-1. This study focuses on the preparation of layered pore structures to provide insights into the sustainable design of carbon materials.

Advanced functional materials based on nanocellulose/Mxene: A review

The escalating need for a sustainable future has driven the advancement of renewable functional materials. Nanocellulose, derived from the abundant natural biopolymer cellulose, demonstrates noteworthy characteristics, including high surface area, crystallinity, mechanical strength, and modifiable chemistry. When combined with two-dimensional (2D) graphitic materials, nanocellulose can generate sophisticated hybrid materials with diverse applications as building blocks, carriers, scaffolds, and reinforcing constituents. This review highlights the progress of research on advanced functional materials based on the integration of nanocellulose, a versatile biopolymer with tailorable properties, and MXenes, a new class of 2D transition metal carbides/nitrides known for their excellent conductivity, mechanical strength, and large surface area. By addressing the challenges and envisioning future prospects, this review underscores the burgeoning opportunities inherent in MXene/nanocellulose composites, heralding a sustainable frontier in the field of materials science.

Separator engineering: Assisting lithium salt dissociation and constructing LiF-rich solid electrolyte interphases for high-rate lithium metal batteries

Challenges associated with lithium dendrite growth and the formation of dead lithium significantly limit the achievable energy density of lithium metal batteries (LMBs), particularly under high operating current densities. Our innovative design employs a state-of-the-art 2500 separator featuring a meticulously engineered cellulose acetate (CA) coating (CA@2500) to suppress dendrite nucleation and propagation. The CO functional groups in CA enhances charge transfer kinetics and triggering the decomposition of lithium bis(trifluoromethanesulfonyl)imide (LiTFSI), which leads to the formation of a more robust solid electrolyte interphase (SEI) composed primarily of LiF. Moreover, the introduction of polar functional groups in the CA enhances the separator's hydrophilic properties, facilitating the uniform Li+ flux and creating a conductive pathway for efficient lithium migration. As a result, the CA@2500 separator exhibits a high lithium-ion transfer number (0.88) and conductivity. The lithium symmetric cell assembles with the CA@2500 separator displays a stable cycling performance over 5500 h at a current density and capacity of 10 mA cm-2 and 10 mAh cm-2, respectively. Additionally, LPF battery with CA@2500 separator shows an excellent capacity retention at 0.2 C with an average decay of 0.055 % per cycle. Moreover, a high capacity of 105 mAh g-1 is maintained after 500 cycles at 5 C with an average decay of only 0.027 % per cycle. This work achieved high stability of LMBs through simplified engineering.

A comprehensive review on preparation and functional application of the wood aerogel with natural cellulose framework

As the traditional aerogel has defects such as poor mechanical properties, complicated preparation process, high energy consumption and non-renewable, wood aerogel as a new generation of aerogel shows unique advantages. With a natural cellulose framework, wood aerogel is a novel nano-porous material exhibiting exceptional properties such as light weight, high porosity, large specific surface area, and low thermal conductivity. Furthermore, its adaptability to further functionalization enables versatile applications across diverse fields. Driven by the imperative for sustainable development, wood aerogel as a renewable and eco-friendly material, has garnered significant attention from researchers. This review introduces preparation methods of wood aerogel based on the top-down strategy and analyzes the factors influencing their key properties intending to obtain wood aerogels with desirable properties. Avenues for realizing its functionality are also explored, and research progress across various domains are surveyed, including oil-water separation, conductivity and energy storage, as well as photothermal conversion. Finally, potential challenges associated with wood aerogel exploitation and utilization are addressed, alongside discussions on future prospects and research directions. The results emphasize the broad research value and future prospects of wood aerogels, which are poised to drive high-value utilization of wood and foster the development of green multifunctional aerogels.

Developments in conducting polymer-, metal oxide-, and carbon nanotube-based composite electrode materials for supercapacitors: a review

Supercapacitors are the latest development in the field of energy storage devices (ESDs). A lot of research has been done in the last few decades to increase the performance of supercapacitors. The electrodes of supercapacitors are modified by composite materials based on conducting polymers, metal oxide nanoparticles, metal-organic frameworks, covalent organic frameworks, MXenes, chalcogenides, carbon nanotubes (CNTs), etc. In comparison to rechargeable batteries, supercapacitors have advantages such as quick charging and high power density. This review is focused on the progress in the development of electrode materials for supercapacitors using composite materials based on conducting polymers, graphene, metal oxide nanoparticles/nanofibres, and CNTs. Moreover, we investigated different types of ESDs as well as their electrochemical energy storage mechanisms and kinetic aspects. We have also discussed the classification of different types of SCs; advantages and drawbacks of SCs and other ESDs; and the use of nanofibres, carbon, CNTs, graphene, metal oxide-nanofibres, and conducting polymers as electrode materials for SCs. Furthermore, modifications in the development of different types of SCs such as pseudo-capacitors, hybrid capacitors, and electrical double-layer capacitors are discussed in detail; both electrolyte-based and electrolyte-free supercapacitors are taken into consideration. This review will help in designing and fabricating high-performance supercapacitors with high energy density and power output, which will act as an alternative to Li-ion batteries in the future.

In situ growth of Zr-based metal-organic frameworks on cellulose sponges for Hg2+ and methylene blue removal

Metal-organic frameworks (MOFs) are characterised by high porosity levels and controllable structures, making them ideal adsorbents for wastewater. However, obtaining substrate materials with mechanical stability, excellent pore accessibility, and good processability for compositing MOF crystal powders to adsorb multiple pollutants in complex aqueous environments is challenging. In this study, porous MOFs@ modified cellulose sponge (MCS) composites were fabricated using MCS as a scaffold to provide anchoring sites for the coordination of Zr4+ ions and further in situ synthesis of MOFs, namely UiO-66@MCS and UiO-66-NH2@MCS, which effectively removed heavy metal ions and organic dyes. MOFs@MCS composites exhibit excellent water and dimensional stability, maintaining the pore structure by ambient drying during reuse. Compared with UiO-66@MCS composite, UiO-66-NH2@MCS composite exhibited a higher adsorption capacity of 224.5 mg·g-1 for Hg2+ and 400.9 mg·g-1 for methylene blue (MB). The adsorption of Hg2+ onto the MOFs@MCS composites followed the Langmuir and pseudo-second-order models, whereas the Freundlich and pseudo-second-order models were more suitable for MB adsorption. Moreover, the MOFs@MCS composites exhibited excellent reusability and were selective for the removal of Hg2+. Overall, this approach effectively combines Zr-based MOFs with mechanically and dimensionally stable porous cellulose sponges, rendering the approach suitable for purifying complex wastewater.

Biomimetic Dual Absorption-Adsorption Networked MXene Aerogel-Pump for Integrated Water Harvesting and Power Generation System

Harvesting atmospheric water and converting it into electricity play vital roles in advancing next-generation energy conversion systems. However, the current water harvester systems suffer from a weak water capture ability and poor recyclability due to high diffusion barriers and low sorption kinetics, which significantly limit their practical application. Herein, we drew inspiration from the natural "Pump effect" observed in wood and successfully developed a dual "absorption-adsorption" networked MXene aerogel atmospheric water harvester (MAWH) through ice templating and confining LiCl processes, thereby serving multiple purposes of clean water production, passive dehumidification, and power generation. The MAWH benefits from the dual H-bond network of MXene and cellulose nanocrystals (absorption network) and the hygroscopic properties of lithium chloride (adsorption network). Furthermore, its aligned wood-like channel structure efficiently eliminates water nucleation near the 3D network, resulting in fast moisture absorption. The developed MAWH demonstrates a high moisture absorption ability of 3.12 g g-1 at 90% relative humidity (RH), featuring rapid vapor transport rates and durable cyclic performance. When compared with commercial desiccants such as the 4A molecular sieve and silica gel, the MAWH can reduce the RH from 80% to 20% within just 6 h. Most notably, our integrated MAWH-based water harvesting-power generation system achieves a high voltage of ∼0.12 V at 77% RH, showcasing its potential for practical application. These developed MAWHs are considered as high-performance atmospheric water harvesters in the water collection and power generation field.

Nanocellulose-based nanogenerators for sensor applications: A review

With the rapid development of the Internet of Things, nanogenerator as a green energy collection technology has attracted great attention in various fields. Specifically, the natural renewable nanocellulose as a raw material can significantly improve the environmental friendliness of the nanocellulose-based nanogenerators, which also makes the nanocellulose based nanogenerators expected to further develop in areas such as wearable devices and sensor networks. This paper mainly reports the application of nanocellulose in nanogenerator, focusing on the sensor. The types, sources and preparation methods of nanocellulose are briefly introduced. At the same time, the special structure of nanocellulose highlights the advantages of nanocellulose in nanogenerators. Then, the application of nanocellulose-based nanogenerators in sensors is introduced. Finally, the future development prospects and shortcomings of this nanogenerator are discussed.

Exploring nanocellulose frontiers: A comprehensive review of its extraction, properties, and pioneering applications in the automotive and biomedical industries

Material is an inseparable entity for humans to serve different purposes. However, synthetic polymers represent a major category of anthropogenic pollutants with detrimental impacts on natural ecosystems. This escalating environmental issue is characterized by the accumulation of non-biodegradable plastic materials, which pose serious threats to the health of our planet's ecosystem. Cellulose is becoming a focal point for many researchers due to its high availability. It has been used to serve various purposes. Recent scientific advancements have unveiled innovative prospects for the utilization of nanocellulose within the area of advanced science. This comprehensive review investigates deeply into the field of nanocellulose, explaining the methodologies employed in separating nanocellulose from cellulose. It also explains upon two intricately examined applications that emphasize the pivotal role of nanocellulose in nanocomposites. The initial instance pertains to the automotive sector, encompassing cutting-edge applications in electric vehicle (EV) batteries, while the second exemplifies the use of nanocellulose in the field of biomedical applications like otorhinolaryngology, ophthalmology, and wound dressing. This review aims to provide comprehensive information starting from the definitions, identifying the sources of the nanocellulose and its extraction, and ending with the recent applications in the emerging field such as energy storage and biomedical applications.

A nanocellulose molecularly imprinted membrane: Preparation, characterization and application in targeted separation of taxane 10-deacetylbaccatin III

Targeted separation of active phytochemicals is urgently needed in the natural medicine field. In this paper, due to the natural porosity and high biocompatibility of cellulose, a nanocellulose membrane combined with surface molecular imprinting was successfully prepared; the efficient nanocellulose-based molecular imprinted membrane (NC-MIM) provided good adsorption for the targeted separation of phytochemicals such as 10-deacetylbaccatin III (10-DAB), an essential intermediate in the synthesis of the anticancer drug paclitaxel. Through a series of characterization and adsorption experiments, the adsorption mechanism of NC-MIM was determined. At pH 8.0 and temperatures of 20 °C-40 °C, the maximum capacity of NC-MIM for adsorption of 10-DAB reached 66.90 mg g - 1, and the content of 10-DAB was dramatically increased 17.5-fold after adsorption. The specific adsorption results showed that NC-MIM had excellent capacity for targeted separation of 10-DAB from among taxane structural analogues. Even after ten cycles, NC-MIM demonstrated a remarkable adsorption capacity of 86.43%, thereby indicating exceptional selectivity and stability. The successful implementation of NC-MIM for green, safe, and efficient enrichment of phytochemicals from plants provides a promising new approach and valuable insights into its practical application.

The Critical Roles of Water in the Processing, Structure, and Properties of Nanocellulose

The cellulose industry depends heavily on water owing to the hydrophilic nature of cellulose fibrils and its potential for sustainable and innovative production methods. The emergence of nanocellulose, with its excellent properties, and the incorporation of nanomaterials have garnered significant attention. At the nanoscale level, nanocellulose offers a higher exposure of hydroxyl groups, making it more intimate with water than micro- and macroscale cellulose fibers. Gaining a deeper understanding of the interaction between nanocellulose and water holds the potential to reduce production costs and provide valuable insights into designing functional nanocellulose-based materials. In this review, water molecules interacting with nanocellulose are classified into free water (FW) and bound water (BW), based on their interaction forces with surface hydroxyls and their mobility in different states. In addition, the water-holding capacity of cellulosic materials and various water detection methods are also discussed. The review also examines water-utilization and water-removal methods in the fabrication, dispersion, and transport of nanocellulose, aiming to elucidate the challenges and tradeoffs in these processes while minimizing energy and time costs. Furthermore, the influence of water on nanocellulose properties, including mechanical properties, ion conductivity, and biodegradability, are discussed. Finally, we provide our perspective on the challenges and opportunities in developing nanocellulose and its interplay with water.

Applications of functionalized porous carbon from bio-waste of Alnus nepalensis in energy storage devices and industrial wastewater treatment

This research investigates the utility of functionalized porous carbon (FPC), derived from the waste wood of Alnus nepalensis. It demonstrates FPC's dual suitability as a versatile component for energy storage systems, specifically supercapacitors, and its impressive capacity to adsorb malachite green (MG) dye from industrial wastewater. The synthesis of FPC occurred through a controlled two-step process: initial activation of wood powder with H3PO4, followed by carbonization at 400 °C for 3 h in a tube furnace. To comprehensively evaluate the material's attributes, multiple analytical methods were employed: Brunauer-Emmet-Teller (BET) analysis, Transmission Electron Microscopy (TEM) imaging, X-ray Diffraction (XRD) analysis, Raman spectroscopy, and Fourier Transform Infrared Spectroscopy (FTIR) spectroscopy. The prepared FPC exhibited desirable characteristics essential for achieving electrochemical performances and adsorption of dyes as well. TEM revealed voids within the material's structure, while BET confirmed high porosity with an active surface area of 1498 m2/g, a pore volume of 1.2 cm³/g, and a pore size of 4.6 nm featuring a harmonious presence of both micropores and mesopores. XRD and Raman spectroscopy confirmed FPC's amorphous state, and FTIR indicated oxygenated functional groups. As a supercapacitor electrode material, FPC demonstrated a specific capacitance of 156.3 F/g at 1A/g current density, an energy density of 5.1 Wh/Kg, a power density of 183.6 W/kg, and enduring cycling stability, retaining 98.4 % performance after 1000 charge-discharge cycles at 3A/g current density. In terms of dye adsorption, FPC exhibited remarkable efficiency. At a pH of 10.5 for MG dye, 0.030g of FPC displayed peak adsorption capacity, removing 95.6 % of 20 ppm MG within 2 min and an even more impressive 99.6 % within 6 min. These findings confirm FPC's potential from Alnus nepalensis as an outstanding supercapacitor electrode material and a rapid, efficient adsorbent for MG removal from industrial wastewater. This research suggests promising applications in energy storage and environmental remediation.

First-Principles Dynamics Investigation of Germanium as an Anode Material in Multivalent-Ion Batteries

Germanium, a promising electrode material for high-capacity lithium ion batteries (LIBs) anodes, attracted much attention because of its large capacity and remarkably fast charge/discharge kinetics. Multivalent-ion batteries are of interest as potential alternatives to LIBs because they have a higher energy density and are less prone to safety hazards. In this study, we probed the potential of amorphous Ge anodes for use in multivalent-ion batteries. Although alloying Al and Zn in Ge anodes is thermodynamically unstable, Mg and Ca alloys with Ge form stable compounds, Mg2.3Ge and Ca2.4Ge that exhibit higher capacities than those obtained by alloying Li, Na, or K with Ge, corresponding to 1697 and 1771 mA·h·g-1, respectively. Despite having a slightly lower capacity than Ca-Ge, Mg-Ge shows an approximately 150% smaller volume expansion ratio (231% vs. 389%) and three orders of magnitude higher ion diffusivity (3.0 × 10-8 vs. 1.1 × 10-11 cm2 s-1) than Ca-Ge. Furthermore, ion diffusion in Mg-Ge occurs at a rate comparable to that of monovalent ions, such as Li+, Na+, and K+. The outstanding performance of the Mg-Ge system may originate from the coordination number of the Ge host atoms and the smaller atomic size of Mg. Therefore, Ge anodes could be applied in multivalent-ion batteries using Mg2+ as the carrier ion because its properties can compete with or surpass monovalent ions. Here, we report that the maximum capacity, volume expansion ratio, and ion diffusivities of the alloying electrode materials can be understood using atomic-scale structural properties, such as the host-host and host-ion coordination numbers, as valuable indicators.

Cellulose Nanofibril Stabilized Pickering Emulsion Templated Aerogel with High Oil Absorption Capacity

Nanocellulose-based aerogels, featuring a three-dimensional porous structure, are considered as a desirable green absorbent because of their exceptional absorption performance as well as the abundance and renewability of the raw material. However, these aerogels often require hydrophobic modification or carbonization, which is often environmentally harmful and energy-intensive. In this study, we introduce a Pickering-emulsion-templating approach to fabricate a cellulose nanofibril (CNF) aerogel with a hierarchical pore structure, allowing for high oil absorption capacity. n-Hexane-CNF oil-in-water Pickering emulsions are prepared as an emulsion template, which is further lyophilized to create a hollow microcapsule-based CNF (HM-CNF) aerogel with a density ranging from 1.3 to 6.1 mg/cm3 and a porosity of ≥99.6%. Scanning electron microscopy and Brunauer-Emmett-Teller analyses reveal the HM-CNF aerogel's hierarchical pore structure, originating from the CNF Pickering emulsion template, and also confirm the aerogel's very high surface area of 216.6 m2/g with an average pore diameter of 8.6 nm. Furthermore, the aerogel exhibits a maximum absorption capacity of 354 g/g and 166 g/g for chloroform and n-hexadecane, respectively, without requiring any surface modification or chemical treatment. These combined findings highlight the potential of the Pickering-emulsion-templated CNF aerogel as an environmentally sustainable and high-performance oil absorbent.

High Rate Performance Supercapacitors Based on N, O Co-Doped Hierarchical Porous Carbon Foams Synthesized via Chemical Blowing and Dual Templates

N, O Co-Doped porous carbon materials are promising electrode materials for supercapacitors. However, it is still a challenge to prepare high capacitance performance N, O Co-Doped porous carbon materials with balanced pore structure. In this work, a simple chemical blowing method was developed to produce hierarchal porous carbon materials with Zn(NO3)2·6H2O and Fe(NO3)3·9H2O as the foaming agents and precursors of dual templates. Soybean protein isolate served as a self-doping carbon source. The amount of Fe(NO3)3·9H2O influenced the microstructure, element content and capacitance performance of the obtained porous carbon materials. The optimized sample CZnFe-5 with the addition of 5% Fe(NO3)3·9H2O displayed the best capacitance performance. The specific capacitance reached 271 F g-1 at 0.2 A g-1 and retained 133 F g-1 at 100 A g-1. The CZnFe-5//CZnFe-5 symmetric supercapacitors delivered a maximum energy density of 16.83 Wh kg-1 and good stability with capacitance retention of 86.33% after 40,000 cycles tests at 50 A g-1. The symmetric supercapacitors exhibited potential applications in lighting LED bulbs with a voltage of 3 V. This work provides a new strategy for the synthesis of hierarchical porous carbon materials for supercapacitors from low-cost biomass products.

Current advances of nanocellulose application in biomedical field

Nanocellulose (NC) is a natural fiber that can be extracted in fibrils or crystals form from different natural sources, including plants, bacteria, and algae. In recent years, nanocellulose has emerged as a sustainable biomaterial for various medicinal applications including drug delivery systems, wound healing, tissue engineering, and antimicrobial treatment due to its biocompatibility, low cytotoxicity, and exceptional water holding capacity for cell immobilization. Many antimicrobial products can be produced due to the chemical functionality of nanocellulose, such disposable antibacterial smart masks for healthcare use. This article discusses comprehensively three types of nanocellulose: cellulose nanocrystals (CNC), cellulose nanofibrils (CNF), and bacterial nanocellulose (BNC) in view of their structural and functional properties, extraction methods, and the distinctive biomedical applications based on the recently published work. On top of that, the biosafety profile and the future perspectives of nanocellulose-based biomaterials have been further discussed in this review.

Novel Design of Perovskite-Structured Neodymium Cobalt Oxide Nanoparticle-Embedded Graphene Oxide Nanocomposites as Efficient Active Materials of Energy Storage Devices

In recent years, electrochemical supercapacitors are expected to represent the future of energy storage device technology. Specifically, the excellent electrochemical performance with long cycle life, high energy, and power density is considered an essential criterion for commercial applications. Herein, we constructed a novel composite of neodymium cobalt oxide-encapsulated graphene oxide nanocomposite (NCO/GO) via a simple and robust method for a symmetric supercapacitor (SSC) device. The prepared samples were securitized by X-ray diffraction, Fourier transform infrared spectroscopy, Raman, X-ray photoelectron spectroscopy, field emission scanning electron microscopy, high-resolution transmission electron microscopy, and Brunauer-Emmett-Teller analysis. The as-synthesized NCO/GO is deposited on nickel foam (NF) and used as a supercapacitor electrode (NCO/GO/NF), which exhibits superior specific capacitance (Cs) of 1080.92 F g-1 at 1 A g-1 and fantastic cycling life with ∼89.42% retention after 10,000 cycles at 10 A g-1 in 1.0 M KOH aqueous electrolyte. A tremendous electrochemical performance of the hybrid nanocomposite electrode is obtained from the good redox activity and synergistic effects of the NCO spherical-like nanoparticles combined with the GO nanosheets. Furthermore, the assembled SSC device delivers significantly enhanced power density (932.93 Wh kg-1) and energy density (210.42 mWh kg-1). Moreover, the SSCs exhibit excellent cycling stability with ∼82.19% capacity retaining over 10,000 charge/discharge cycles. Remarkably, a 1.8 V red light-emitting diode (LED) can be lit up for more than 10 min by series connection SSCs. Thus, the obtained results indicated that the NCO/GO/NF//NCO/GO/NF symmetric device has a robust and cost-effective electrode material for high-performance supercapacitor systems.

Printed Electrodes Based on Vanadium Dioxide and Gold Nanoparticles for Asymmetric Supercapacitors

Printed energy storage components attracted attention for being incorporated into bendable electronics. In this research, a homogeneous and stable ink based on vanadium dioxide (VO2) is hydrothermally synthesized with a non-toxic solvent. The structural and morphological properties of the synthesized material are determined to be well-crystalline monoclinic-phase nanoparticles. The charge storage mechanisms and evaluations are specified for VO2 electrodes, gold (Au) electrodes, and VO2/Au electrodes using cyclic voltammetry, galvanostatic charge-discharge, and electrochemical impedance spectroscopy. The VO2 electrode shows an electrical double layer and a redox reaction in the positive and negative voltage ranges with a slightly higher areal capacitance of 9 mF cm-2. The VO2/Au electrode exhibits an areal capacitance of 16 mF cm-2, which is double that of the VO2 electrode. Due to the excellent electrical conductivity of gold, the areal capacitance 18 mF cm-2 of the Au electrode is the highest among them. Based on that, Au positive electrodes and VO2 negative electrodes are used to build an asymmetric supercapacitor. The device delivers an areal energy density of 0.45 μWh cm-2 at an areal power density of 70 μW cm-2 at 1.4 V in the aqueous electrolyte of potassium hydroxide. We provide a promising electrode candidate for cost-effective, lightweight, environmentally friendly printed supercapacitors.

Biomass-Derived Flexible Carbon Architectures as Self-Supporting Electrodes for Energy Storage

With the swift advancement of the wearable electronic devices industry, the energy storage components of these devices must possess the capability to maintain stable mechanical and chemical properties after undergoing multiple bending or tensile deformations. This circumstance has expedited research efforts toward novel electrode materials for flexible energy storage devices. Nonetheless, among the numerous materials investigated to date, the incorporation of metal current collectors or insulative adhesives remains requisite, which entails additional costs, unnecessary weight, and high contact resistance. At present, biomass-derived flexible architectures stand out as a promising choice in electrochemical energy device applications. Flexible self-supporting properties impart a heightened mechanical performance, obviating the need for additional binders and lowering the contact resistance. Renewable, earth-abundant biomass endows these materials with cost-effectiveness, diversity, and modulable chemical properties. To fully exploit the application potential in biomass-derived flexible carbon architectures, understanding the latest advancements and the comprehensive foundation behind their synthesis assumes significance. This review delves into the comprehensive analysis of biomass feedstocks and methods employed in the synthesis of flexible self-supporting carbon electrodes. Subsequently, the advancements in their application in energy storage devices are elucidated. Finally, an outlook on the potential of flexible carbon architectures and the challenges they face is provided.

Electrochemical Properties of Laser-Printed Multilayer Anodes for Lithium-Ion Batteries

New electrode architectures promise huge potential for improving batteries' electrochemical properties, such as power density, energy density, and lifetime. In this work, the use of laser-induced forward transfer (LIFT) was employed and evaluated as a tool for the development of advanced electrode architectures. For this purpose, it was first confirmed that the printing process has no effect on the transferred battery material by comparing the electrochemical performance of the printed anodes with state-of-the-art coated ones. For this, polyvinylidene fluoride (PVDF) was used as a binder and n-methyl-2-pyrrolidone (NMP) as a solvent, which is reported to be printable. Subsequently, multilayer electrodes with flake-like and spherical graphite particles were printed to test if a combination of their electrochemical related properties can be realized with measured specific capacities ranging from 321 mAh·g-1 to 351 mAh·g-1. Further, a multilayer anode design with a silicon-rich intermediate layer was printed and electrochemically characterized. The initial specific capacity was found to be 745 mAh·g-1. The presented results show that the LIFT technology offers the possibility to generate alternative electrode designs, promoting research in the optimization of 3D battery systems.

Hybrid Mesoporous Carbon/Copper Ferrite Electrode for Asymmetric Supercapacitors

Asymmetric supercapacitors (ASCs) with two dissimilar electrodes are known to exhibit relatively moderate energy and power densities. If electrodes derived from earth-abundant materials or renewable resources such as lignocellulosic biomass (LCB) are used for fabrication, energy storage systems are expected to become less expensive and more sustainable. Hybrid electrode materials have advantages such as higher surface area, better chemical stability, and superior energy density. This study reports on the synthesis of a novel hybrid electrode material containing porous carbon (POC) and copper ferrite, which is designated as POC@Cu-ferrite, and its electrochemical performance in ASC configuration. Corn stover derived hydrochar is utilized for the sol-gel synthesis of POC@Cu-ferrite hybrid material using earth-abundant Cu and Fe-based precursors. This material is characterized using X-ray diffraction (XRD), Raman spectroscopy, Brunauer-Emmett-Teller (BET) surface area analyzer, and scanning and transmission electron microscopy (SEM/TEM). As-synthesized Cu-ferrite is found to contain 89.2% CuFe2O4 and 10.8% Fe2O3, whereas other phases such as Fe3O4, CuFeO2, and CuO are observed for the POC@Cu-ferrite. BET-specific surface area (SSA) and pore volume of POC@Cu-ferrite are observed as 1068 m2/g and 0.72 cm3/g, respectively. POC@Cu-ferrite hybrid electrode is used with POC opposite electrode to fabricate ASC, which is tested using Gamry G-300 potentiostat/galvanostat/ZRA to obtain cyclic voltammetry (CV) profiles and galvanostatic charge-discharge (GCD) plots. ASC is also prepared using Cu-ferrite and POC materials and its specific capacitance and stability are compared with ASCs prepared with POC@Cu-ferrite and POC or graphene nanoplatelets (GNPs) electrodes. POC@Cu-ferrite hybrid electrode is found to be superior with a 2-fold higher capacitance and significant electrochemical stability over 100 GCD cycles as compared to the Cu-ferrite electrode.

The Influence of Reduced Graphene Oxide on the Texture and Chemistry of N,S-Doped Porous Carbon. Implications for Electrocatalytic and Energy Storage Applications

In this work, we study the influence of reduced graphene oxide (rGO) on the morphology and chemistry of highly porous N,S-doped carbon cryogels. Simultaneously, we propose an easily upscalable route to prepare such carbons by adding graphene oxide (GO) in as-received suspended form to the aqueous solution of the ι-carrageenan and urea precursors. First, 1.25-5 wt% GO was incorporated into the dual-doped polymer matrix. The CO2, CO, and H2O emitted during the thermal treatments resulted in the multifaceted modification of the textural and chemical properties of the porous carbon. This facilitated the formation of micropores through self-activation and resulted in a substantial increase in the apparent surface area (up to 1780 m2/g) and pore volume (up to 1.72 cm3/g). However, adding 5 wt% GO led to overactivation. The incorporated rGO has an ordering effect on the carbon matrix. The evolving oxidative species influence the surface chemistry in a complex way, but sufficient N and S atoms (ca. 4 and >1 at%, respectively) were preserved in addition to the large number of developing defects. Despite the complexity of the textural and chemical changes, rGO increased the electrical conductivity monotonically. In alkaline oxygen reduction reaction (ORR) tests, the sample with 1.25 wt% GO exhibited a 4e- mechanism and reasonable stability, but a higher rGO content gradually compromised the performance of the electrodes. The sample containing 5 wt% GO was the most sensitive under oxidative conditions, but after stabilization it exhibited the highest gravimetric capacitance. In Li-ion battery tests, the coulombic efficiency of all the samples was consistently above 98%, indicating the high potential of these carbons for efficient Li-ion insertion and reinsertion during the charge-discharge process, thereby providing a promising alternative for graphite-based anodes. The cell from the 1.25 wt% GO sample showed an initial discharge capacity of 313 mAh/g, 95.1% capacity retention, and 99.3% coulombic efficiency after 50 charge-discharge cycles.

Use of Few-Layer Graphene Synthesized under Conditions of Self-Propagating High-Temperature Synthesis for Supercapacitors Applications

Graphene nanostructures (GNSs) are among the most promising materials for producing supercapacitors. However, GNSs are still not used in creating supercapacitors due to the impossibility of obtaining large volumes of high-quality material at an acceptable cost. In our previous works, we have shown the possibility of synthesizing large volumes of few-layer graphene (FLG, the number of layers is not more than five) from cyclic biopolymers under conditions of self-propagating high-temperature synthesis (SHS). Using the SHS process makes it possible to synthesize large volumes of FLG without Stone-Wales defects. This work is devoted to the study of the possibility of using FLG synthesized under the conditions of the SHS process in the creation of supercapacitors. It was found that the synthesized FLG makes it possible to obtain better results than using classical materials, namely activated carbon (AC). It was found that the sample based on FLG had a higher specific capacitance of 65 F × g-1 compared to the sample from AC, the specific capacitance of which was 35 F × g-1; for a speed of 5 mV × s-1, these values were170 and 64 F × g-1, respectively. The drop in capacitance over 1000 cycles was 4%, indicating a sufficiently high FLG stability, allowing us to consider FLG as a prospective material for use in supercapacitors.

Polyoxometalate-Stabilized Silver Nanoparticles and Hybrid Electrode Assembly Using Activated Carbon

The intersection between the field of hybrid materials and that of electrochemistry is a quickly expanding area. Hybrid combinations usually consist of two constituents, but new routes toward more complex and versatile electroactive hybrid designs are quickly emerging. The objective of the present work is to explore novel triple hybrid material integrating polyoxometalates (POMs), silver nanoparticles (Ag0 NPs), and activated carbon (AC) and to demonstrate its use as a hybrid electrode in a symmetric supercapacitor. The tri-component nanohybrid (AC/POM-Ag0 NPs) was fabricated through the combination of AC with pre-synthesized ∼27 nm POM-protected Ag0 NPs (POM-Ag0 NPs). The POM-Ag0 NPs were prepared using a green electrochemical method and characterized via UV-vis and IR spectroscopy, electron microscopy, dynamic light scattering (DLS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and cyclic voltammetry (CV). Afterward, the AC/POM-Ag0 NPs ternary nanocomposite material was constructed and characterized. The electrochemical behavior of AC/POM-Ag0 NPs' modified electrodes reveal that the nanomaterial is electroactive and exhibits a moderately higher specific capacitance (81 F/g after 20 cycles) than bare AC electrodes (75 F/g) in a symmetrical supercapacitor configuration in the voltage range 0 to 0.75 V and 20 mV/s, demonstrating the potential use of this type of tri-component nanohybrid for electrochemical applications.

A Flexible Supercapacitor Based on Niobium Carbide MXene and Sodium Anthraquinone-2-Sulfonate Composite Electrode

MXene-based composites have been widely used in electric energy storage device. As a member of MXene, niobium carbide (Nb2C) is a good electrode candidate for energy storage because of its high specific surface area and electronic conductivity. However, a pure Nb2C MXene electrode exhibits limited supercapacitive performance due to its easy stacking. Herein, sodium anthraquinone-2-sulfonate (AQS) with high redox reactivity was employed as a tailor to enhance the accessibility of ions and electrolyte and enhance the capacitance performance of Nb2C MXene. The resulting Nb2C-AQS composite had three-dimensional porous layered structures. The supercapacitors (SCs) based on the Nb2C-AQS composite exhibited a considerably higher electrochemical capacitance (36.3 mF cm-2) than the pure Nb2C electrode (16.8 mF cm-2) at a scan rate of 20 mV s-1. The SCs also exhibited excellent flexibility as deduced from the almost unchanged capacitance values after being subjected to bending. A capacitance retention of 99.5% after 600 cycles was observed for the resulting SCs, indicating their good cycling stability. This work proposes a surface modification method for Nb2C MXene and facilitates the development of high-performance SCs.

Fabrication of Composite Gel Electrolyte and F-Doping Carbon/Silica Anode from Electro-Spun P(VDF-HFP)/Silica Composite Nanofiber Film for Advanced Lithium-Ion Batteries

The aim of this work is to effectively combine the advantages of polymer and ceramic nanoparticles and improve the comprehensive performance of lithium-ion batteries (LIBs) diaphragm. A flexible film composed of electro-spun P(VDF-HFP) nanofibers covered by a layer of mesoporous silica (P(VDF-HFP)@SiO₂) was synthesized via a sol-gel transcription method, then used as a scaffold to absorb organic electrolyte to make gel a electrolyte membrane (P(VDF-HFP)@SiO₂-GE) for LIBs. The P(VDF-HFP)@SiO₂-GE presents high electrolyte uptake (~1000 wt%), thermal stability (up to ~350 °C), ionic conductivity (~2.6 mS cm^-1 at room temperature), and excellent compatibility with an active Li metal anode. Meanwhile, F-doping carbon/silica composite nanofibers (F-C@SiO₂) were also produced by carbonizing the P(VDF-HFP)@SiO₂ film under Ar and used to make an electrode. The assembled F-C@SiO₂|P(VDF-HFP)@SiO₂-GE|Li half-cell showed long-cycle stability and a higher discharge specific capacity (340 mAh g^-1) than F-C@SiO₂|Celgard 2325|Li half-cell (175 mAh g^-1) at a current density of 0.2 A g^-1 after 300 cycles, indicating a new way for designing and fabricating safer high-performance LIBs.

Facile and adhesive-free method for bonding nanofiber membrane onto thermoplastic polystyrene substrate to fabricate 3D cell culture platforms

Nanofiber (NF) membranes have been highlighted as functional materials for biomedical applications owing to their high surface-to-volume ratios, high permeabilities, and extracellular matrix-like biomimetic structures. Because many in vitro platforms for biomedical applications are made of thermoplastic polymers (TP), a simple and leak-free method for bonding NF membranes onto TP platforms is essential. Here, we propose a facile but leak-free localized thermal bonding method for integrating 2D or 3D-structured NF membrane onto a TP supporting substrate while preserving the pristine nanofibrous structure of the membrane, based on localized preheating of the substrate. A methodology for determining the optimal preheating temperature was devised based on a numerical simulation model considering the melting temperature of the NF material and was experimentally validated by evaluating bonding stability and durability under cell culture conditions. The thermally-bonded interface between the NF membrane and TP substrate was maintained stably for 3 weeks allowing the successful construction of an intestinal barrier model. The applicability of the localized thermal bonding method was also demonstrated on various combinations of TP materials (e.g., polystyrene and polymethylmethacrylate) and geometries of the supporting substrate, including a culture insert and microfluidic chip. We expect the proposed localized thermal bonding method to contribute toward broadening and realizing the practical applications of functional NF membranes in various biomedical fields.

A Fe2(SO4)3-assisted approach towards green synthesis of cuttlefish ink-derived carbon nanospheres for high-performance supercapacitors

The conversion of renewable biomass resources into advanced electrode materials through green, simple, and economical methods has become an important research direction in energy storage. In this study, Fe-decorated N/S-codoped porous carbon nanospheres have been successfully fabricated from cuttlefish ink through Fe₂(SO₄)₃-assisted hydrothermal carbonization coupled with heat treatment. The effects of Fe₂(SO₄)₃ dosage on the structure, chemical composition, and capacitive property of carbon nanospheres were investigated. Herein, environmentally friendly Fe₂(SO₄)₃ plays a multifunctional role as the graphitization catalyst, dopant, and morphology-regulating agent. Benefitting from the moderate graphitization degree, great heteroatom content and hierarchical porous structure, the prepared carbon nanospheres exhibit high specific capacitance (311.9 F g^-1 at a current density of 0.5 A g^-1), good rate capability (19.1% decrease in specific capacitance as current density increases from 0.5 to 10 A g^-1), and ideal cycling stability (94.3% capacitance retention after 5000 cycles). In addition, the symmetric supercapacitor assembled with the carbon nanosphere electrodes achieves an energy density of 9.7 Wh kg^-1 at a power density of 0.25 kW kg^-1 and maintains 91.3% capacitance after 10,000 cycles. The desirable electrochemical performance of cuttlefish ink-derived carbon nanosphere material makes it a potential electrode candidate for supercapacitors.

An Overview of the Emerging Technologies and Composite Materials for Supercapacitors in Energy Storage Applications

Energy storage is one of the challenges currently confronting the energy sector. However, the invention of supercapacitors has transformed the sector. This modern technology's high energy capacity, reliable supply with minimal lag time, and extended lifetime of supercapacitors have piqued the interest of scientists, and several investigations have been conducted to improve their development. However, there is room for improvement. Consequently, this review presents an up-to-date investigation of different supercapacitor technologies' components, operating techniques, potential applications, technical difficulties, benefits, and drawbacks. In addition, it thoroughly highlights the active materials used to produce supercapacitors. The significance of incorporating every component (electrode and electrolyte), their synthesis approach, and their electrochemical characteristics are outlined. The research further examines supercapacitors' potential in the next era of energy technology. Finally, concerns and new research prospects in hybrid supercapacitor-based energy applications that are envisaged to result in the development of ground-breaking devices, are highlighted.

Inspired by Wood: Thick Electrodes for Supercapacitors

The emergence and development of thick electrodes provide an efficient way for the high-energy-density supercapacitor design. Wood is a kind of biomass material with porous hierarchical structure, which has the characteristics of a straight channel, uniform pore structure, good mechanical strength, and easy processing. The wood-inspired low-tortuosity and vertically aligned channel architecture are highly suitable for the construction of thick electrochemical supcapacitor electrodes with high energy densities. This review summarizes the design concepts and processing parameters of thick electrode supercapacitors inspired by natural woods, including wood-based pore structural design regulation, electric double layer capacitances (EDLCs)/pseudocapacitance construction, and electrical conductivity optimization. In addition, the optimization strategies for preparing thick electrodes with wood-like structures (e.g., 3D printing, freeze-drying, and aligned-low tortuosity channels) are also discussed in detail. Further, this review presents current challenges and future trends in the design of thick electrodes for supercapacitors with wood-inspired pore structures. As a guideline, the brilliant blueprint optimization will promote sustainable development of wood-inspired structure design for thick electrodes and broaden the application scopes.

Safe Etching Route of Nb2SnC for the Synthesis of Two-Dimensional Nb2CTx MXene: An Electrode Material with Improved Electrochemical Performance

In this study, low-temperature synthesis of a Nb₂SnC non-MAX phase was carried out via solid-state reaction, and a novel approach was introduced to synthesize 2D Nb₂CT_x MXenes through selective etching of Sn from Nb₂SnC using mild phosphoric acid. Our work provides valuable insights into the field of 2D MXenes and their potential for energy storage applications. Various techniques, including XRD, SEM, TEM, EDS, and XPS, were used to characterize the samples and determine their crystal structures and chemical compositions. SEM images revealed a two-dimensional layered structure of Nb₂CT_x, which is consistent with the expected morphology of MXenes. The synthesized Nb₂CT_x showed a high specific capacitance of 502.97 Fg^-1 at 1 Ag^-1, demonstrating its potential for high-performance energy storage applications. The approach used in this study is low-cost and could lead to the development of new energy storage materials. Our study contributes to the field by introducing a unique method to synthesize 2D Nb₂CT_x MXenes and highlights its potential for practical applications.

Research Progress on Biomimetic Nanomaterials for Electrochemical Glucose Sensors

Diabetes has become a chronic disease that necessitates timely and accurate detection. Among various detection methods, electrochemical glucose sensors have attracted much attention because of low cost, real-time detection, and simple and easy operation. Nonenzymatic biomimetic nanomaterials are the vital part in electrochemical glucose sensors. This review article summarizes the methods to enhance the glucose sensing performance of noble metal, transition metal oxides, and carbon-based materials and introduces biomimetic nanomaterials used in noninvasive glucose detection in sweat, tear, urine, and saliva. Based on these, this review provides the foundation for noninvasive determination of trace glucose for diabetic patients in the future.

Biomimetic mineralization of nacre-inspired multiple crosslinked PVA/CaAlg/SiO2 membrane with simultaneously enhanced mechanical and separation properties

Inspired by the natural nacre structure, we propose a new strategy to fabricate mineralized, multiple crosslinked hydrogel membranes with the "rigid silica in soft polymer" nacre-like structure. In-situ SiO₂ nanoparticles (NPs) and polyvinyl alcohol/sodium alginate (PVA/NaAlg) are used to simulate the rigid "bricks" and soft "mortar" compositions of nacre, respectively. The nacre-like mineralized (PVA/CaAlg/SiO₂) membrane showed a higher tensile strength of 4.1 ± 0.08 MPa, excellent pure water flux of 170 ± 3 L/m²h, and an oil/water rejection rate of 99 %. The interwoven hierarchal structure, similar to nacre, was determined by SEM analysis. In addition, incorporating SiO₂ NPs increases the anti-swelling, roughness, and hydrophilicity of the membranes. PVA/CaAlg/SiO₂ membrane exhibited excellent superhydrophilicity (WCA value was 0°) and superoleophobicity underwater (OCA value was 162°). PVA/CaAlg/SiO₂ membrane also showed excellent separation performance for water-soluble organic pollutants and can be used for dye separation with rejection efficiencies of 99.5 %, 99.1 %, and 98.3 % for Congo red (CR), Alizarin red (AR), and Sunset yellow (SY), respectively. Moreover, PVA/CaAlg/SiO₂ membrane had outstanding long-term filtration and antifouling performance. The biomineralization-inspired structure provides a promising technique that can be used to prepare high-performance organic-inorganic membranes with great promise for wastewater separation application.

Enhanced hybrid hydrogel based on wheat husk lignin-rich nanocellulose for effective dye removal

Polyvinyl alcohol (PVA) hydrogels were enhanced mechanically through the addition of lignin-rich nanocellulose (LCN), soluble ash (SA) and montmorillonite (MMT) for dye removal. The hybrid hydrogels reinforced with 33.3 wt% of LCN had a 163.0% increase in storage modulus as compared to the PVA/0LCN-33.3SM hydrogel. LCN can be added to the PVA hydrogel to alter its rheological properties. Additionally, hybrid hydrogels were highly efficient in removing methylene blue from wastewater, which was attributed to the synergistic effects of the PVA matrix supporting embedded LCN, MMT, and SA. The adsorption time (0–90 min) showed that the hydrogels containing MMT and SA had high removal efficiency, and the adsorption of methylene blue (MB) by PVA/20LCN-13.3SM was greater than 95.7% at 30°C. It was found that MB efficiency decreased with a high MMT and SA content. Our study provided a new method for the fabrication of polymers-based eco-friendly, low-cost and robust physical hydrogels for the MB removal.

In Situ Fabrication of High Dielectric Constant Composite Films with Good Mechanical and Thermal Properties by Controlled Reduction

As a common two-dimensional carbon material, graphene has been widely doped into polymers to prepare high-performance dielectric materials. However, the shortcomings of graphene, such as large specific surface area and poor dispersion, limit its further application. Therefore, in this work, to solve the problem regarding the uniform dispersion of graphene in the matrix, in situ polymerization was used to prepare graphene/polyimide films, in which 1,4-diiodobutane was used as a reduction agent to prevent the aggregation of graphene oxide (GO) during imidization. High dielectric constant composite films were obtained by adjusting the ratio of 1,4-diiodobutane in GO. The results show that the resulting graphene/polyimide composite film possessed a dielectric constant of up to 197.5, which was more than 58 times higher than that of the polyimide (PI) film. Furthermore, compared to the pure PI film, the composite films showed better thermal stability and mechanical properties. Thermal performance tests showed that the 1,4-diiodobutane added during the preparation of the composite film was thermally decomposed, and there was no residue. We believe our preparation method can be extended to other high dielectric composite films, which will facilitate their further development and application in high power density energy storage materials.

Hierarchical Biobased Macroporous/Mesoporous Carbon: Fabrication, Characterization and Electrochemical/Ion Exchange Properties

With the goal of improving the mechanical properties of porous hierarchical carbon, cellulosic fiber fabric was incorporated into the resorcinol/formaldehyde (RF) precursor resins. The composites were carbonized in an inert atmosphere, and the carbonization process was monitored by TGA/MS. The mechanical properties, evaluated by nanoindentation, show an increase in the elastic modulus due to the reinforcing effect of the carbonized fiber fabric. It was found that the adsorption of the RF resin precursor onto the fabric stabilizes its porosity (micro and mesopores) during drying while incorporating macropores. The textural properties are evaluated by N₂ adsorption isotherm, which shows a surface area (BET) of 558 m²g^-1. The electrochemical properties of the porous carbon are evaluated by cyclic voltammetry (CV), chronocoulometry (CC), and electrochemical impedance spectroscopy (EIS). Specific capacitances (in 1 M H₂SO₄) of up to 182 Fg^-1 (CV) and 160 Fg^-1 (EIS) are measured. The potential-driven ion exchange was evaluated using Probe Bean Deflection techniques. It is observed that ions (protons) are expulsed upon oxidation in acid media by the oxidation of hydroquinone moieties present on the carbon surface. In neutral media, when the potential is varied from values negative to positive of the potential of zero charge, cation release, followed by anion insertion, is found.

Silver Decorated and Graphene Wrapped Polypyrrole@Ni(OH)2 Quaternary Nanocomposite for High Performance Energy Storage Devices

In this work, silver (Ag) anchored over graphene (GN) wrapped polypyrrole (PPy)@ nickel hydroxide (Ni(OH)₂) nanocomposites were synthesized through a combination of oxidative polymerization and hydrothermal processes. The synthesized Ag/GN@PPy-Ni(OH)₂ nanocomposites were characterized for their morphological characteristics by field emission scanning electron microscopy (FESEM), while the structural investigations were done by X-ray diffraction and X-ray photoelectron spectroscopy (XPS). The FESEM studies showed Ni(OH)₂ flakes and silver particles attached over the surface of PPy globules, along with the presence of GN sheets and spherical silver particles. The structural analysis also showed the presence of constituents, i.e., Ag, Ni(OH)₂, PPy, GN, and their interaction, therefore vouching that the synthesis protocol is efficacious. The electrochemical (EC) investigations were done in potassium hydroxide (1 M KOH) using a three electrode setup. The quaternary Ag/GN@PPy-Ni(OH)₂ nanocomposite electrode showed the highest specific capacity of 237.25 C g^-1. The highest electrochemical performance of the quaternary nanocomposite is associated with the synergistic/additional effect of PPy, Ni(OH)₂, GN, and Ag. The assembled supercapattery with Ag/GN@PPy-Ni(OH)₂ as a positive and activated carbon (AC) as a negative electrode displayed eminent energy density of 43.26 Wh kg^-1 with the associated power density of 750.00 W kg^-1 at a current density of 1.0 A g^-1. The cyclic stability of the supercapattery (Ag/GN@PPy-Ni(OH)₂//AC), comprising a battery-type electrode, displayed a high cyclic stability of 108.37% after 5500 cycles.

Recent Advances in Two-Dimensional MXene for Supercapacitor Applications: Progress, Challenges, and Perspectives

MXene is a type of two-dimensional (2D) transition metal carbide and nitride, and its promising energy storage materials highlight its characteristics of high density, high metal-like conductivity, tunable terminals, and charge storage mechanisms known as pseudo-alternative capacitance. MXenes are a class of 2D materials synthesized by chemical etching of the A element in MAX phases. Since they were first discovered more than 10 years ago, the number of distinct MXenes has grown substantially to include numerous M_nX_n-1 (n = 1, 2, 3, 4, or 5), solid solutions (ordered and disordered), and vacancy solids. To date, MXenes used in energy storage system applications have been broadly synthesized, and this paper summarizes the current developments, successes, and challenges of using MXenes in supercapacitors. This paper also reports the synthesis approaches, various compositional issues, material and electrode topology, chemistry, and hybridization of MXene with other active materials. The present study also summarizes MXene's electrochemical properties, applicability in pliant-structured electrodes, and energy storage capabilities when using aqueous/non-aqueous electrolytes. Finally, we conclude by discussing how to reshape the face of the latest MXene and what to consider when designing the next generation of MXene-based capacitors and supercapacitors.

The Influence of Physical Mixing and Impregnation on the Physicochemical Properties of Pine Wood Activated Carbon Produced by One-Step ZnCl2 Activation

In this study, two different sample preparation methods to synthesize activated carbon from pine wood were compared. The pine wood activated carbon was prepared by mixing ZnCl₂ by physical mixing, i.e., "dry mixing" and impregnation, i.e., "wet mixing" before high temperature carbonization. The influence of these methods on the physicochemical properties of activated carbons was examined. The activated carbon was analyzed using nitrogen sorption (surface area, pore volume and pore size distribution), XPS, density, Raman spectroscopy, and electrochemistry. Physical mixing led to a slightly higher density carbon (1.83 g/cm³) than wet impregnation (1.78 g/cm³). Raman spectroscopy analysis also showed that impregnation led to activated carbon with a much higher degree of defects than physical mixing, i.e., I_D/I_G = 0.86 and 0.89, respectively. The wet impregnated samples also had better overall textural properties. For example, for samples activated with 1:1 ratio, the total pore volume was 0.664 vs. 0.637 cm³/g and the surface area was 1191 vs. 1263 m²/g for dry and wet mixed samples, respectively. In the electrochemical application, specifically in supercapacitors, impregnated samples showed a much better capacitance at low current densities, i.e., 247 vs. 146 F/g at the current density of 0.1 A/g. However, the physically mixed samples were more stable after 5000 cycles: 97.8% versus 94.4% capacitance retention for the wet impregnated samples.

Bio-Template Synthesis of V2O3@Carbonized Dictyophora Composites for Advanced Aqueous Zinc-Ion Batteries

In terms of new-generation energy-storing devices, aqueous zinc-ion batteries (AZIBs) are becoming the prime candidates because of their inexpensive nature, inherent safety, environmental benignity and abundant resources. Nevertheless, due to a restrained selection of cathodes, AZIBs often perform unsatisfactorily under long-life cycling and high-rate conditions. Consequently, we propose a facile evaporation-induced self-assembly technique for preparing V₂O₃@carbonized dictyophora (V₂O₃@CD) composites, utilizing economical and easily available biomass dictyophora as carbon sources and NH₄VO₃ as metal sources. When assembled in AZIBs, the V₂O₃@CD exhibits a high initial discharge capacity of 281.9 mAh g^-1 at 50 mA g^-1. The discharge capacity is still up to 151.9 mAh g^-1 after 1000 cycles at 1 A g^-1, showing excellent long-cycle durability. The extraordinary high electrochemical effectiveness of V₂O₃@CD could be mainly attributed to the formation of porous carbonized dictyophora frame. The formed porous carbon skeleton can ensure efficient electron transport and prevent V₂O₃ from losing electrical contact due to volume changes caused by Zn²⁺ intercalation/deintercalation. The strategy of metal-oxide-filled carbonized biomass material may provide insights into developing high-performance AZIBs and other potential energy storage devices, with a wide application range.

Biocompatible, Resilient, and Tough Nanocellulose Tunable Hydrogels

Hydrogels have been proposed as potential candidates for many different applications. However, many hydrogels exhibit poor mechanical properties, which limit their applications. Recently, various cellulose-derived nanomaterials have emerged as attractive candidates for nanocomposite-reinforcing agents due to their biocompatibility, abundance, and ease of chemical modification. Due to abundant hydroxyl groups throughout the cellulose chain, the grafting of acryl monomers onto the cellulose backbone by employing oxidizers such as cerium(IV) ammonium nitrate ([NH₄]₂[Ce(NO₃)₆], CAN) has proven a versatile and effective method. Moreover, acrylic monomers such as acrylamide (AM) may also polymerize by radical methods. In this work, cerium-initiated graft polymerization was applied to cellulose-derived nanomaterials, namely cellulose nanocrystals (CNC) and cellulose nanofibrils (CNF), in a polyacrylamide (PAAM) matrix to fabricate hydrogels that display high resilience (~92%), high tensile strength (~0.5 MPa), and toughness (~1.9 MJ/m³). We propose that by introducing mixtures of differing ratios of CNC and CNF, the composite's physical behavior can be fine-tuned across a wide range of mechanical and rheological properties. Moreover, the samples proved to be biocompatible when seeded with green fluorescent protein (GFP)-transfected mouse fibroblasts (3T3s), showing a significant increase in cell viability and proliferation compared to samples comprised of acrylamide alone.

Highly Porous Carbon Aerogels for High-Performance Supercapacitor Electrodes

In recent years, porous carbon materials with high specific surface area and porosity have been developed to meet the commercial demands of supercapacitor applications. Carbon aerogels (CAs) with three-dimensional porous networks are promising materials for electrochemical energy storage applications. Physical activation using gaseous reagents provides controllable and eco-friendly processes due to homogeneous gas phase reaction and removal of unnecessary residue, whereas chemical activation produced wastes. In this work, we have prepared porous CAs activated by gaseous carbon dioxide, with efficient collisions between the carbon surface and the activating agent. Prepared CAs display botryoidal shapes resulting from aggregation of spherical carbon particles, whereas activated CAs (ACAs) display hollow space and irregular particles from activation reactions. ACAs have high specific surface areas (2503 m² g^-1) and large total pore volumes (1.604 cm³ g^-1), which are key factors for achieving a high electrical double-layer capacitance. The present ACAs achieved a specific gravimetric capacitance of up to 89.1 F g^-1 at a current density of 1 A g^-1, along with a high capacitance retention of 93.2% after 3000 cycles.

Research Progress of the Ion Activity Coefficient of Polyelectrolytes: A Review

Polyelectrolyte has wide applications in biomedicine, agriculture and soft robotics. However, it is among one of the least understood physical systems because of the complex interplay of electrostatics and polymer nature. In this review, a comprehensive description is presented on experimental and theoretical studies of the activity coefficient, one of the most important thermodynamic properties of polyelectrolyte. Experimental methods to measure the activity coefficient were introduced, including direct potentiometric measurement and indirect methods such as isopiestic measurement and solubility measurement. Next, progress on the various theoretical approaches was presented, ranging from analytical, empirical and simulation methods. Finally, challenges for future development are proposed on this field.

Carbonized Leather Waste: A Review and Conductivity Outlook

The carbonization of collagen-based leather waste to nitrogen-containing carbon is reviewed with respect to the preparation, characterization of carbonized products, and applications proposed in the literature. The resulting nitrogen-containing carbons with fibrous morphology have been used as adsorbents in water pollution treatment, in electrocatalysis, and especially in electrodes of energy-storage devices, such as supercapacitors and batteries. Although electrical conductivity has been implicitly exploited in many cases, the quantitative determination of this parameter has been addressed in the literature only marginally. In this report, attention has been newly paid to the determination of conductivity and its dependence on carbonization temperature. The resulting powders cannot be compressed into pellets for routine conductivity determination. A new method has been used to follow the resistivity of powders as a function of pressure up to 10 MPa. The conductivity at this pressure increased from 9.4 × 10^-8 S cm^-1 for carbonization at 500 °C to 5.3 S cm^-1 at 1000 °C. The conductivity of the last sample was comparable with conducting polymers such as polypyrrole. The carbonized leather thus has the potential to be used in applications requiring electrical conduction.

A Review of Current Trends on Polyvinyl Alcohol (PVA)-Based Solid Polymer Electrolytes

Presently, the rising concerns about the fossil fuel crisis and ecological deterioration have greatly affected the world economy and hence have attracted attention to the utilization of renewable energies. Among the renewable energy being developed, supercapacitors hold great promise in broad applications such as electric vehicles. Presently, the main challenge facing supercapacitors is the amount of energy stored. This, however, does not satisfy the increasing demand for higher energy storage devices, and therefore, intensive research is being undertaken to overcome the challenges of low energy density. The purpose of this review is to report on solid polymer electrolytes (SPEs) based on polyvinyl alcohol (PVA). The review discussed the PVA as a host polymer in SPEs followed by a discussion on the influence of conducting salts. The formation of SPEs as well as the ion transport mechanism in PVA SPEs were discussed. The application and development of PVA-based polymer electrolytes on supercapacitors and other energy storage devices were elucidated. The fundamentals of electrochemical characterization for analyzing the mechanism of supercapacitor applications, such as EIS, LSV and dielectric constant, are highlighted. Similarly, thermodynamic transport models of ions and their mechanism about temperature based on Arrhenius and Vogel-Tammann-Fulcher (VTF) are analyzed. Methods for enhancing the electrochemical performance of PVA-based SPEs were reported. Likely challenges facing the current electrolytes are well discussed. Finally, research directions to overcome the present challenges in producing SPEs are proposed. Therefore, this review is expected to be source material for other researchers concerned with the development of PVA-based SPE material.

One-Step Solvothermal Synthesis by Ethylene Glycol to Produce N-rGO for Supercapacitor Applications

Graphene and its derivatives have emerged as peerless electrode materials for energy storage applications due to their exclusive electroactive properties such as high chemical stability, wettability, high electrical conductivity, and high specific surface area. However, electrodes from graphene-based composites are still facing some substantial challenges to meet current energy demands. Here, we applied one-pot facile solvothermal synthesis to produce nitrogen-doped reduced graphene oxide (N-rGO) nanoparticles using an organic solvent, ethylene glycol (EG), and introduced its application in supercapacitors. Electrochemical analysis was conducted to assess the performance using a multi-channel electrochemical workstation. The N-rGO-based electrode demonstrates the highest specific capacitance of 420 F g^-1 at 1 A g^-1 current density in 3 M KOH electrolyte with the value of energy (28.60 Whkg^-1) and power (460 Wkg^-1) densities. Furthermore, a high capacitance retention of 98.5% after 3000 charge/discharge cycles was recorded at 10 A g^-1. This one-pot facile solvothermal synthetic process is expected to be an efficient technique to design electrodes rationally for next-generation supercapacitors.

Valorization of Banana Peel Using Carbonization: Potential Use in the Sustainable Manufacturing of Flexible Supercapacitors

Sustainable and environmentally friendly activated carbon from biomass materials is proposed to produce supercapacitors from banana peels and has the potential to replace the non-sustainable and hazardous process from either graphite or/and fossil fuels. In order to determine the potential of using banana peel for supercapacitor application, raw banana peel, a bio-waste, was activated both mechanically and chemically to observe the real differences. The sample was activated at 700 °C and chemically activated using KOH. Characterization of activated banana peel was performed using FTIR, DLS, TGA and XRD analytical equipment. FTIR analysis revised the presence of hydroxyl, carbonyl and aromatic compounds on a banana peel cellulose-based carbon. The TGA results proved that 700 °C could be sufficient to totally carbonize banana peel. DLS clearly showed a strong difference between the carbonized and KOH-activated material in particle size distribution. Meanwhile, surface area analysis using BET displayed an increase from 553.862 m²/g to 565.024 m²/g BET in surface area (SBET) when carbon was activated using KOH with a nitrogen isotherm at 77.350 K. Specific capacitance was increased from 0.3997 Fg^-1 to 0.821 Fg^-1, suggesting more than a 100% increase in the specific capacity due to KOH activation, as proved by the cyclic voltammetry (CV) curve. The X-ray diffraction results revealed the patterns of activated carbon. The findings demonstrated the feasibility of using banana peel waste as a low-cost and sustainable material for the preparation of flexible supercapacitor batteries.