Bonding agents of low fusing cpTi porcelains: Elemental and morphological characterization

Bonding of resin luting materials to titanium and titanium alloy

Recently in Japan, due to the increased prices of palladium and gold, cast titanium restorations have been included in the Japanese national health insurance system. The purpose of this review was to survey the available literature on titanium bonding systems, focusing on the adhesive monomer in the luting agent in order to expand the application of resin-bonded fixed prostheses made of titanium or titanium alloys. It was found that adhesive monomers are effective for bonding to titanium, and provide results equal to the procedures of silanization and tribochemical silica coating. A primer or a luting agent, including 10-methacryloyloxydecyl dihydrogen phosphate (MDP), methacryloyloxyalkyl thiophosphate derivative (MEPS), 6-methacryloxyhexyl phosphonoacetate (6-MHPA), and 4-methacryloyloxyethl trimellitate anhydride (4-META) promotes bonding characteristics between titanium and the resin material.

Influence of Sandblasting and Chemical Etching on Titanium 99.2-Dental Porcelain Bond Strength

The metal-ceramic interface requires proper surface preparation of both metal and ceramic substrates. This process is complicated by the differences in chemical bonds and physicochemical properties that characterise the two materials. However, adequate bond strength at the interface and phase composition of the titanium-bioceramics system is essential for the durability of dental implants and improving the substrates' functional properties. In this paper, the authors present the results of a study determining the effect of mechanical and chemical surface treatment (sandblasting and etching) on the strength and quality of the titanium-low-fusing dental porcelain bond. To evaluate the strength of the metal-ceramic interface, the authors performed mechanical tests (three-point bending) according to EN ISO 9693 standard, microscopic observations (SEM-EDS), and Raman spectroscopy studies. The results showed that depending on the chemical etching medium used, different bond strength values and failure mechanisms of the metal-ceramic system were observed. The analyzed samples met the requirements of EN ISO 9693 for metal-ceramic systems and received strength values above 25 MPa. Higher joint strength was obtained for the samples after sandblasting and chemical etching compared to the samples subjected only to sandblasting.

Bond strength of commercial veneering porcelain to experimental cast Ti-Cr alloy

This study evaluated bond strengths of three commercial veneering porcelains to experimental cast titanium-chromium (Ti-Cr) alloy and commercially pure titanium (cp-Ti) via three-point bending test. After the bending test, the fractured specimens were analyzed using an electron probe microanalyzer (EPMA). The Ti-Cr specimens showed lower bond strengths than the cp-Ti specimens, irrespective of the layering porcelain material; however, all the strengths exceeded the minimum requirement of ISO 9693-1:2012 (>25 MPa). EPMA revealed that titanium and/or chromium elements were detected on the debonded porcelain surface of the Ti-Cr and cp-Ti specimens in the case of the higher bond strength. Contrastingly, the residual porcelain was retained on the metallic surface in the case of the lower bond strength. Although porcelain bonding to the titanium alloy is influenced by porcelain type, the Ti-Cr alloy could be feasible for porcelain-fused-to-metal restorations.

Investigation on the properties of borate bonding agents: Ti6Al4V-porcelain bonding, chemical durability and preliminary cytotoxicity

The purpose of this study was to investigate the properties of the borate bonding agents (BBAS) including chemical durability, biocompatibility and bonding characteristics of porcelain to Ti6Al4V. The bond strength was performed by the three-point bending test. And the chemical durability and ion release of BBAS were tested by chemical soaking and inductively coupled plasma optical emission spectrometry (ICP-OES), respectively. Moreover, cytotoxicity was evaluated by cell viability assay and cell adhesion using human osteosarcoma cells (MG-63) and cell counter kit-8 (CCK-8) assay. To investigate the influences of composition and microstructure changes on all the properties mentioned above, the ¹¹B and ²⁷Al spectra and infrared spectra of BBAS were measured by solid-state nuclear magnetic resonance (SSNMR) and Fourier transform infrared spectroscopy (FTIR), respectively. Combined with all these properties of BBAS, the optimal addition proportion of Al₂O₃ into BBAS is 20 mol%. The relative contents of [BO3], [BO4], [AlO4], [AlO5] and [AlO6] have great influences on these properties of BBAS. BBAS, possessing excellent chemical durability, good biocompatibility and low ion release and being an effective way to improve the Ti6Al4V-porcelain bond strength, have significant clinical potentials in porcelain fused to metal restorations.

The effect of thermal cycling on the shear bond strength of porcelain/Ti-6Al-4V interfaces

The aim of the study was to evaluate the effect of thermal cycling on the shear bond strength of the porcelain/Ti-6Al-4V interfaces prepared by two different processing routes and metallic surface conditions. Polished and SiO2 particle abraded Ti-6Al-4V alloy and Triceram bonder porcelain were used to produce the interfaces. Porcelain-to-metal specimens were processed by conventional furnace firing and hot pressing. Thermal cycling was performed in Fusayama's artificial saliva for 5000 cycles between 5 ± 1 and 60 ± 2°C. After thermal cycling, shear bond tests were carried out by using a custom-made stainless steel apparatus. The results were analyzed using t-Student test and non-parametric Kruskal-Wallis test (p<0.01). Most of the polished-fired specimens were fractured during thermal cycling; thus, it was not possible to obtain the shear bond strength results for this group. Sandblasted-fired, polished-hot pressed, and sandblasted-hot pressed specimens presented the shear bond strength values of 76.2 ± 15.9, 52.2 ± 23.6, and 59.9 ± 22.0 MPa, respectively. Statistical analysis indicated that thermal cycling affected the polished specimens processed by firing, whereas a significant difference was not observed on the other groups.

Effect of Bonding Agent Application Method on Titanium-Ceramic Bond Strength

PURPOSE

Although milled titanium may be used as a substructure in fixed and implant prosthodontics, the application of the veneering porcelain presents particular challenges compared to traditional alloys. To address these challenges, some Ti ceramic systems incorporate the application of a bonding agent prior to the opaque layer. Vita Titankeramik's bonding agent is available as a powder, paste, and spray-on formulation. We examined the effect of these three application methods on the bond strength.

MATERIALS AND METHODS

Four titanium bars were milled from each of 11 wafers cut from grade II Ti using the Kavo Everest milling unit and a custom-designed milling toolpath. An experienced technician prepared the 25 × 3 × 0.5 mm(3) metal bars and applied bonding agent using one of three application methods, and then applied opaque, dentin, and enamel porcelains according to manufacturer's instructions to a 8 × 3 × 1 mm(3) porcelain. A control group received no bonding agent prior to porcelain application. The four groups (n = 11) were blindly tested for differences in bond strength using a universal testing machine in a three-point bend test configuration, based on ISO 9693-1:2012.

RESULTS

The average (SD) bond strengths for the control, powder, paste, and spray-on groups, respectively, were: 24.8 (2.6), 24.6 (2.6), 25.3 (4.0), and 24.1 (3.9) MPa. One-way ANOVA and Tukey's multiple comparison tests were performed between all groups. There were no statistically significant differences among groups (p = 0.951).

CONCLUSION

Titanium-porcelain bond strength was not affected by the use of a bonding agent or its application method when tested by ISO 9693-1 standard.

Improvement in Ti-porcelain bonding by SiO(2) modification of titanium surface through cast method

This study aimed to improve Ti-porcelain bonding strength through SiO2 modifications. Wax patterns were coated with SiO2 mixed with tetraethoxy silane (group C), patterns without coating were used as controls and subdivided into sandblasting group (group S) and polishing group (group P). Castingsurfaces were analyzed with XRD, while Ti-ceramic interfaces were characterized using SEM/EDS. Metal-ceramic specimens were tested in three point bending, and characterizations were also analyzed with SEM/EDS of porcelain debonding surfaces. In group C, SiO2 and Ti5Si3 phases were observed; SEM micrograph showed that Ti-porcelain had a compacted interface, and EDS maps of the interface illustrated the diffusion of Si, Al, and Sn to Ti, and cohesive fracture within the bonding agent. The bond strength of group C was 39.04±5.0 MPa, which was 15% higher than that of group S and 32% higher than that of group P. SiO2 coating could improve Ti-porcelain bond strength.

Influence of the processing route of porcelain/Ti-6Al-4V interfaces on shear bond strength

This study aims at evaluating the two-fold effect of initial surface conditions and dental porcelain-to-Ti-6Al-4V alloy joining processing route on the shear bond strength. Porcelain-to-Ti-6Al-4V samples were processed by conventional furnace firing (porcelain-fused-to-metal) and hot pressing. Prior to the processing, Ti-6Al-4V cylinders were prepared by three different surface treatments: polishing, alumina or silica blasting. Within the firing process, polished and alumina blasted samples were subjected to two different cooling rates: air cooling and a slower cooling rate (65°C/min). Metal/porcelain bond strength was evaluated by shear bond test. The data were analyzed using one-way ANOVA followed by Tuckey's test (p<0.05). Before and after shear bond tests, metallic surfaces and metal/ceramic interfaces were examined by Field Emission Gun Scanning Electron Microscope (FEG-SEM) equipped with Energy Dispersive X-Ray Spectroscopy (EDS). Shear bond strength values of the porcelain-to-Ti-6Al-4V alloy interfaces ranged from 27.1±8.9MPa for porcelain fused to polished samples up to 134.0±43.4MPa for porcelain fused to alumina blasted samples. According to the statistical analysis, no significant difference were found on the shear bond strength values for different cooling rates. Processing method was statistically significant only for the polished samples, and airborne particle abrasion was statistically significant only for the fired samples. The type of the blasting material did not cause a statistically significant difference on the shear bond strength values. Shear bond strength of dental porcelain to Ti-6Al-4V alloys can be significantly improved from controlled conditions of surface treatments and processing methods.

Effect of ZrN coating by magnetron sputtering and sol-gel processed silica coating on titanium/porcelain interface bond strength

In this study, a coating technique was applied to improve the bond strength of titanium (Ti) porcelain. ZrN coating was prepared by magnetron sputtering, and silica coating was processed by a sol-gel method. The treated surfaces of the specimens were analyzed by X-ray diffraction, and the Ti/porcelain interface was investigated by scanning electron microscopy (SEM) and energy dispersive spectroscopy. The coated specimens appeared fully coherent to the Ti substrate. The fractured bonding surface was also investigated by SEM. The residual porcelain on the metal surface could be observed in the ZrN group and silica group, but there was no obvious porcelain remaining in the control group. A three-point-bending test showed that the bonding strength of the ZrN group (45.99 ± 0.65 MPa) was higher than the silica group (37.77 ± 0.78 MPa) (P < 0.001) and control group (29.48 ± 1.01 MPa) (P < 0.001), while that of the silica group was significantly higher than the control group (P < 0.001). In conclusion, conditioning the ceramic surface with ZrN and silica coatings resulted in a stronger Ti/porcelain bond. ZrN coating by magnetron sputtering was a more effective way to improve the bond strength between Ti and porcelain compared with sol-gel processed silica coating in this study.