Wear rates of retentive versus nonretentive reverse total shoulder arthroplasty liners in an in vitro wear simulation

Effect of vitamin E-enhanced highly cross-linked polyethylene on wear rate and particle debris in anatomic total shoulder arthroplasty: a biomechanical comparison to ultrahigh-molecular-weight polyethylene

BACKGROUND

Particle-induced osteolysis resulting from polyethylene wear remains a source of implant failure in anatomic total shoulder designs. Modern polyethylene components are irradiated in an oxygen-free environment to induce cross-linking, but reducing the resulting free radicals with melting or heat annealing can compromise the component's mechanical properties. Vitamin E has been introduced as an adjuvant to thermal treatments. Anatomic shoulder arthroplasty models with a ceramic head component have demonstrated that vitamin E-enhanced polyethylene show improved wear compared with highly cross-linked polyethylene (HXLPE). This study aimed to assess the biomechanical wear properties and particle size characteristics of a novel vitamin E-enhanced highly cross-linked polyethylene (VEXPE) glenoid compared to a conventional ultrahigh-molecular-weight polyethylene (UHMWPE) glenoid against a cobalt chromium molybdenum (CoCrMo) head component.

METHODS

Biomechanical wear testing was performed to compare the VEXPE glenoid to UHMWPE glenoid with regard to pristine polyethylene wear and abrasive endurance against a polished CoCrMo alloy humeral head in an anatomic shoulder wear-simulation model. Cumulative mass loss (milligrams) was recorded, and wear rate calculated (milligrams per megacycle [Mc]). Under pristine wear conditions, particle analysis was performed, and functional biologic activity (FBA) was calculated to estimate particle debris osteolytic potential. In addition, 95% confidence intervals for all testing conditions were calculated.

RESULTS

The average pristine wear rate was statistically significantly lower for the VEXPE glenoid compared with the HXLPE glenoid (0.81 ± 0.64 mg/Mc vs. 7.00 ± 0.45 mg/Mc) (P < .05). Under abrasive wear conditions, the VEXPE glenoid had a statistically significant lower average wear rate compared with the UHMWPE glenoid comparator device (18.93 ± 5.80 mg/Mc vs. 40.47 ± 2.63 mg/Mc) (P < .05). The VEXPE glenoid demonstrated a statistically significant improvement in FBA compared with the HXLPE glenoid (0.21 ± 0.21 vs. 1.54 ± 0.49 (P < .05).

CONCLUSIONS

A new anatomic glenoid component with VEXPE demonstrated significantly improved pristine and abrasive wear properties with lower osteolytic particle debris potential compared with a conventional UHMWPE glenoid component. Vitamin E-enhanced polyethylene shows early promise in shoulder arthroplasty components. Long-term clinical and radiographic investigation needs to be performed to verify if these biomechanical wear properties translate to diminished long-term wear, osteolysis, and loosening.

Total shoulder arthroplasty in patients with dementia or mild cognitive impairment

Background

Anatomic total shoulder arthroplasty (ATSA) and reverse total shoulder arthroplasty (RTSA) reliably alleviate pain and restore shoulder function for a variety of indications. However, these procedures are not well-studied in patients with neurocognitive impairment. Therefore, the purpose of this study was to investigate whether patients with dementia or mild cognitive impairment (MCI) have increased odds of surgical or medical complications following arthroplasty.

Methods

The PearlDiver database was queried from 2010 through October 2021 to identify a cohort of patients who underwent either ATSA or RTSA and had a minimum 2-year follow-up. Current Procedural Terminology and International Classification of Diseases codes were used to stratify this cohort into three groups: (1) patients with dementia, (2) patients with MCI, and (3) patients with neither condition. Surgical and medical complication rates were compared among these three groups.

Results

The overall prevalence of neurocognitive impairment among patients undergoing total shoulder arthroplasty was 3.0% in a cohort of 92,022 patients. Patients with dementia had increased odds of sustaining a periprosthetic humerus fracture (odds ratio [OR] = 1.46, P < .001), developing prosthesis instability (OR = 1.72, P < .001), and undergoing revision arthroplasty (OR = 1.55, P = .003) after RTSA compared to patients with normal cognition. ATSA patients with dementia did not have an elevated risk of surgical complications or revision. Conversely, RTSA patients with MCI did not have an elevated risk of complications or revision, although ATSA patients with MCI had greater odds of prosthesis instability (OR = 2.51, P = .008). Additionally, patients with neurocognitive impairment had elevated odds of medical complications compared to patients with normal cognition, including acute myocardial infarction and cerebrovascular accident.

Conclusion

Compared to patients with normal cognition, RTSA patients with preoperative dementia and ATSA patients with preoperative MCI are at increased risk for surgical complications. Moreover, both ATSA and RTSA patients with either preoperative MCI or dementia are at increased risk for medical complications. As the mean age in the U.S. continues to rise, special attention should be directed towards patients with neurocognitive impairment to minimize postoperative complications aftertotal shoulder arthroplasty, and the risks of this surgery more carefully discussed with patients and their families and caretakers.

Allergic reaction and metal hypersensitivity after shoulder joint replacement

PURPOSE

Metal ion release may cause local and systemic effects and induce hypersensitivity reactions. The aim of our study is first to determine if implant-related hypersensitivity correlates to patient symptoms or not; second, to assess the rate of hypersensitivity and allergies in shoulder arthroplasty.

METHODS

Forty patients with shoulder replacements performed between 2015 and 2017 were studied with minimum 2-year follow-up; no patient had prior metal implants. Each patient underwent radiographic and clinical evaluation using the Constant-Murley Score (CMS), 22 metal and cement haptens patch testing, serum and urine tests to evaluate 12 metals concentration, and a personal occupational medicine interview.

RESULTS

At follow-up (average 45 ± 10.7 months), the mean CMS was 76 ± 15.9; no clinical complications or radiographic signs of loosening were detected; two nickel sulfate (5%), 1 benzoyl peroxide (2.5%) and 1 potassium dichromate (2.5%) positive findings were found, but all these patients were asymptomatic. There was an increase in serum aluminum, urinary aluminum and urinary chromium levels of 1.74, 3.40 and 1.83 times the baseline, respectively. No significant difference in metal ion concentrations were found when patients were stratified according to gender, date of surgery, type of surgery, and type of implant.

CONCLUSIONS

Shoulder arthroplasty is a source of metal ion release and might act as a sensitizing exposure. However, patch test positivity does not seem to correlate to hypersensitivity cutaneous manifestations or poor clinical results. Laboratory data showed small constant ion release over time, regardless of gender, type of shoulder replacement and implant used.

LEVELS OF EVIDENCE

Level II.

No Difference in Range of Motion in Reverse Total Shoulder Arthroplasty Using Standard or Constrained Liners: A Matched Cohort Study

Background

Prosthetic instability is one of the most common short-term complications following reverse total shoulder arthroplasty (RTSA). Numerous strategies exist to attempt to mitigate this complication, including utilization of constrained polyethylene humeral liners. A concern of constrained humeral liners is that they may come at the expense of restricted rotational range of motion (ROM). The purpose of the present study is to compare range of ROM and patient-reported outcomes (PROs), and satisfaction among matched cohorts using constrained vs. unconstrained liners after RTSA.

Methods

A multicenter shoulder arthroplasty registry was retrospectively reviewed to identify patients with two-year clinical follow-up after RTSA with constrained liners used at the surgeon’s discretion. All patients had the same inlay humeral prosthesis with a 135° neck shaft angle. This study cohort was matched 1:2 to control patients who underwent RTSA with standard liners based on age, sex, total glenoid-sided lateralization, glenosphere diameter, and surgery performed on the dominant arm. Improvement in PROs and ROM was compared between groups.

Results

Twenty-two patients were identified who underwent RTSA with a constrained humeral liner; these were compared to 44 matched patients with standard liners. The groups were found to have no notable differences in demographics, baseline PROs and ROM. At two years postoperatively, both cohorts demonstrated improvements in all PROs without statistically significant differences between the two groups. There were no differences between groups in improvement in any ROM measure, including forward flexion (constrained: 54^°, standard: 57^°, P = .771), external rotation at the side (constrained: 42°, standard: 41°, P = .906) or internal rotation at 90^° of abduction (constrained: 24^°, standard: 20^°, P = .587).

Conclusions

For an inlay humeral prosthesis with a 135^° neck shaft angle, utilization of a constrained liner for RTSA demonstrates no significant difference in ROM or PROs compared to a well-matched cohort of patients who underwent RTSA with a standard polyethylene humeral liner. These are reassuring data for using constrained liners when there is intraoperative concern for prosthetic instability.

The Evolution of Reverse Total Shoulder Arthroplasty-From the First Steps to Novel Implant Designs and Surgical Techniques

Purpose of Review: The purpose of this review is to summarize recent literature regarding the latest design modifications and biomechanical evolutions of reverse total shoulder arthroplasty and their impact on postoperative outcomes. Recent findings: Over the past decade, worldwide implantation rates of reverse total shoulder arthroplasty have drastically increased for various shoulder pathologies. While Paul Grammont’s design principles first published in 1985 for reverse total shoulder arthroplasty remained unchanged, several adjustments were made to address postoperative clinical and biomechanical challenges such as implant glenoid loosening, scapular notching, or limited range of motion in order to maximize functional outcomes and increase the longevity of reverse total shoulder arthroplasty. However, the adequate and stable fixation of prosthetic components can be challenging, especially in massive osteoarthritis with concomitant bone loss. To overcome such issues, surgical navigation and patient-specific instruments may be a viable tool to improve accurate prosthetic component positioning. Nevertheless, larger clinical series on the accuracy and possible complications of this novel technique are still missing.

Tomographic Analysis of Positioning of Reverse Baseplates Positioning

Objective

To verify whether reverse baseplate positioning without the support of intraoperative three-dimensional technology is within the acceptable parameters in the literature and whether glenoid bone deformity (GBD) compromises this positioning.

Methods

Sixty-nine reverse shoulder arthroplasties were evaluated with volumetric computed tomography (CT). Two radiologists performed blinded CT scan analysis and evaluated baseplate position within 2mm of the inferior glenoid; the inclination and version of the baseplate in relation to the Friedman line; and upper and lower screw and baseplate metallic peg end point positionings. The patients were divided according to the presence of GBD for statistical analyses.

Results

The two radiologists concurred reasonably in their interpretations of the following analyzed parameters: baseplate position within 2mm of the inferior glenoid rim (97.1% and 95.7%), baseplate inclination (82.6% and 81.2%), baseplate version (69.6% and 56.5%), the upper screw reaching the base of the coracoid process (71% and 79.7%), the inferior screw remaining inside the scapula (88.4% and 84.1%), and the metallic peg of the baseplate considered intraosseous (88.4% and 72.5%).

Conclusion

Reverse baseplate positioning without intraoperative three-dimensional technology is within the acceptable parameters of the literature, except for baseplate version and upper screw position. GBD did not interfere with baseplate positioning in reverse shoulder arthroplasty.

Wear and damage in retrieved humeral inlays of reverse total shoulder arthroplasty-where, how much, and why?

BACKGROUND

Polyethylene (PE) wear and material degradation have been reported as complications in reverse total shoulder replacements (rTSAs). In this regard, scapular notching is associated with more clinical complications. Therefore, the purposes of the study were to quantify the linear and volumetric wear, as a measure for the amount of removed material, and to qualitatively assess the PE damage modes to describe the material degradation in retrieved rTSA humeral PE inlays that contribute to failure of shoulder replacements. Furthermore, this study aimed to evaluate the effect of scapular notching on PE wear and rim damage of the humeral components.

METHODS

The total study population of 39 humeral inlays contains 2 cohorts that were used for the damage mode analysis and for the wear analysis, respectively. The extent and presence of wear damage modes in 5 defined zones were assessed by a grading system for all PE joint replacements. For quantitative wear analysis the most frequent design (n = 17) was chosen. Using a coordinate-measuring machine and postprocessing software, volumetric wear measurements for the retrieved humeral PE inlays were undertaken. Furthermore, prerevision radiographs were analyzed for scapular notching. Finally, retrieval findings were correlated with clinical and radiographic data to consider the effect of notching and to identify risk of failures for these prostheses.

RESULTS

Damage on the rim of the humeral PE inlays was more frequent and severe than on the intended articulation surface. Irrespective of the damage mode, the inferior rim zone sustained the greatest amount of wear damage followed by the posterior zone. Burnishing, scratching, pitting, and embedded particles are most likely to occur in the articular surface area, whereas surface deformation, abrasion, delamination and gross material degradation are predominantly present in the inferior and posterior rim zones. The retrieved inlays exhibited a mean volumetric wear rate of 296.9 mm³/yr ± 87.0 mm³/yr. However, if the notched and non-notched components were compared, a significant higher volumetric wear rate (296.5 ± 106.1 mm³/yr) was found for the notched components compared to the non-notched group (65.7 ± 7.4 mm³/yr). Generally, there was a significantly greater incidence of damage and greater amount of wear if scapular notching occurred.

CONCLUSION

The notched components showed a 5-fold increase in PE wear rate. Therefore, scapular notching has a strong effect on PE damage and wear. If scapular notching can be clinically avoided, the PE wear performance is in a similar magnitude as found for hip and knee replacements.

Factors Influencing Appropriate Implant Selection and Position in Reverse Total Shoulder Arthroplasty

Reverse shoulder arthroplasty has increased in popularity and has provided improved but somewhat variable results. These variable outcomes may be related to many factors, including implant design, component positioning, specific indication, and patient anatomy. The original Grammont design provided a solution to the high failure rate at the time but was found to have a high rate of scapular notching and poor restoration of rotation. Modern lateralized designs are more consistent in reducing scapular notching while improving range of motion, especially in regards to external rotation. This review article summarizes the effects of modern reverse shoulder prostheses on outcomes.

In vivo volumetric and linear wear measurement of reverse shoulder arthroplasty at minimum 5-year follow-up

BACKGROUND

Reverse shoulder arthroplasty is quickly becoming the most frequently performed glenohumeral joint replacement. The purpose of this study was to evaluate the volumetric and linear wear rates of ultrahigh-molecular-weight polyethylene humeral liners in vivo at a minimum 5-year follow-up.

METHODS

Radiostereometric analysis was used to image 15 patients at terminal range of motion in forward flexion, abduction, external rotation, and internal rotation and with the arm at the side. The relative position and orientation of the glenosphere and polyethylene were identified for each arm position. The apparent intersection of the glenosphere into the polyethylene was recorded as wear. Mean volumetric and linear wear rates were recorded, and Pearson correlation coefficients were applied to the 36-mm liners to assess the relationship between the wear rate and term of service.

RESULTS

The mean reverse shoulder arthroplasty term of service at the time of imaging was 8 ± 1 years (range, 6-11 years). The mean volumetric and linear wear rates for the 36-mm liners (n = 13) were 42 ± 22 mm³/yr (r = 0.688, P = .009) and 0.11 ± 0.03 mm/yr (r = 0.767, P = .002), respectively. The mean volumetric and linear wear rates for the 42-mm liners (n = 2) were 114 ± 44 mm³/yr and 0.17 ± 0.01 mm/yr, respectively. No single arm position was able to capture all recorded wear individually.

CONCLUSION

This study showed volumetric and linear wear rates of approximately 40 mm³/yr and 0.1 mm/yr, respectively, for the 36-mm polyethylene liners. The 42-mm liners showed higher wear rates, although a greater number of subjects is required for conclusive results. In vivo wear of reverse total shoulder arthroplasty is multidirectional and perceptible.

Failed Reverse Shoulder Arthroplasty and Recommendations for Revision

PURPOSE OF REVIEW

The most common complications warranting revision consideration in reverse shoulder arthroplasty (RSA) include instability and its associated causes: infection, periprosthetic fracture, and glenoid baseplate loosening. Management of complications can be challenging and the nuances of treatment are still being elucidated. The focus of this paper is to review the treatment of the failed RSA and discuss evidence-based recommendations for revision.

RECENT FINDINGS

The most common complications requiring revision RSA are instability and infection. The causes for instability can be subdivided into three main subcategories: loss of compression, loss of containment, and impingement. Loss of compression is further broken down into 6 subcategories revolving around abnormal prosthesis positioning, undersized prostheses, or intrinsic soft-tissue tension loss leading to instability. Periprosthetic infection can also lead to instability, yet the most appropriate management for infected RSA remains controversial. Restoring stability by maximizing deltoid and soft tissue tension while avoiding impingement revolves around three basic methods: (1) lateralizing and/or upsizing the glenosphere to an inferior position on the glenoid, (2) use of a more constrained polyethylene insert, and (3) distalizing the humerus by increasing the polyethylene thickness and/or the thickness of the humeral tray. Management of periprosthetic joint infection can be performed in one-stage, two-stage, or "three-stage" procedures all showing good outcomes with two-stage procedures being the most commonly performed. However, persistent positive culture with propriobacterium acnes can occur in up to 25% of cases. In order to limit the associated morbidity from failed revision reverse shoulder arthroplasty, continued research on best management of associated complications is warranted.

Reverse Total Shoulder Arthroplasty: Implant Design Considerations

PURPOSE OF REVIEW

Our understanding of the reverse total shoulder arthroplasty (RTSA) has grown exponentially since Grammont first introduced his design in 1985. There are a multitude of implant-related variables to consider when performing RTSA. The purpose of this article is to provide a review of these design considerations.

RECENT FINDINGS

Current literature demonstrates that the traditional Grammont prosthesis has over 90% survivorship at 10 years. Despite these promising results, there have been concerns raised over the significant rate of scapular notching observed. As a result, the traditional RTSA design has been modified to minimize this complication and maximize impingement-free motion. Modern RTSA designs with a cementless, curved, short-stemmed eccentric onlay humeral component combined with a large, lateralized glenosphere placed in 10° of inferior tilt with > 3.5 mm of inferior overhang have been found to provide excellent results. However, all implant design features must be considered on a case-by-case basis to optimize outcome for each patient. Humeral and glenoid implant design variables have evolved as the biomechanics of RTSA have been further elucidated. Consideration of these variables allows the surgeon to maximize joint efficiency, improve impingement-free range of motion, decrease the risk of scapular notching, preserve bone stock, and minimize the risk of instability.

Wear analysis of explanted conventional metal back polyethylene glenoid liners

INTRODUCTION

Glenoid component wear and loosening is the Achilles heel of total shoulder replacement. Analysis of failed, revised implants might give an insight into the causes of component failure. Volumetric assessment of conventional total shoulder replacement glenoid liner wear rate and scanning electron microscopy was accomplished in this study for the purpose. Coherence scanning interferometry (white light scanner) 3D images were acquired. This method requires no physical contact, ionising radiation or extensive surface preparation.

METHODS

Twenty-four Nottingham total shoulder replacement system metal - back glenoid liners were explanted from revision shoulder arthroplasty cases. A Phase Vision Quartz DBE 800 scanner was used to scan the explanted polyethylene liners. The images of worn liners were registered to the reference image. Differences in wear and wear rate were quantified and central and non-central wear groups were distinguished. The Central wear group had a polyethylene wear rate of 115 ± 55mm3/year (mean ± SD). The non-central group showed a wear rate of 112 ± 42 mm3/year (mean ± SD), which was not significantly different from the central wear group (p = 0.426) Polyethylene liners showing edge wear from unstable shoulder replacements showed a wear rate of 545 mm³/year. Scanning electron microscopy images showed that the polyethylene was wearing in laminar flakes which indicated fatigue wear.

CONCLUSION

The volumetric wear rate was found to be more than twice as fast as in the case of total hip replacement with the acetabular liner made of the same type of polyethylene. Use of coherence scanning interferometry is proposed for wear analysis.

Quantitative evaluation of retrieved reverse total shoulder arthroplasty liner surface deviation and volumetric wear

Polyethylene wear is a known complication in total joint arthroplasty, however, in vivo wear rates in reverse total shoulder arthroplasty (RTSA) remain largely unknown. This study aimed to quantify volumetric and surface deviation changes in retrieved RTSA humeral liners using a novel micro-computed tomography (μCT)-based technique. After IRB-approval, 32 humeral liners (single manufacturer and model) with term-of-service greater than 90 days were analyzed. Clinical demographics and surgical data were collected via chart review. Unworn liners were used as geometric controls. Retrieved and unworn liners underwent μCT scanning. Retrieved liner volumes were isolated, co-registered to controls of matching geometry, and surface deviations of the articulation surface and rim were computed. Differences in total volume loss (TVL), volumetric wear rate (VWR), and surface deviation were reported. Semi-quantitative grading evaluated rim damage presence and severity. Mean term-of-service for all liners was 2.07 ± 1.33 years (range: 0.30-4.73). Mean TVL and VWR were 181.3 ± 208.2 mm³ and 114.5 ± 160.3 mm³ /year, respectively. Mean articulation and rim surface deviations were 0.084 ± 0.065 and 0.177 ± 0.159 mm, respectively. Articulation surface deviation was positively correlated to term-of-service. Rim damage was present on 63% of liners and correlated significantly to rim surface deviation. This study reports in vivo wear rates of retrieved RTSA implants. Our results demonstrate volumetric and articulation surface wear in select RTSA liners that is correlated to term-of-service. Calculation of in vivo wear rates can help bridge the gap between clinical outcomes and experimental models such as wear simulations and computational models. © 2018 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:2007-2014, 2018.

Neer Award 2017: wear rates of 32-mm and 40-mm glenospheres in a reverse total shoulder arthroplasty wear simulation model

BACKGROUND

Larger glenosphere diameters have been used recently to increase prosthesis stability and impingement-free range of motion in reverse total shoulder arthroplasty. The goal of this study was to evaluate the rate of polyethylene wear for 32-mm and 40-mm glenospheres.

METHODS

Glenospheres (32 mm and 40 mm, n = 6/group) and conventional polyethylene humeral liners underwent a 5-million cycle (MC) wear simulation protocol. Abduction-adduction and flexion-extension motion profiles were alternated every 250,000 cycles. At each interval, mass loss was determined and converted to volume loss and wear rate. At 0, 2.5 MC, and 5 MC, liners were imaged using micro-computed tomography to determine surface deviation. White light interferometry was performed on liners and glenospheres at 0 and 5 MC to quantify surface roughness. Wear particle morphology was characterized by environmental scanning electron microscopy.

RESULTS

Total volume loss was significantly higher in 40-mm liners from 1.5 MC onward (P < .05). Overall, volumetric wear rate was significantly higher in 40-mm liners compared with 32-mm glenospheres (81.7 ± 23.9 mm³/MC vs. 68.0 ± 18.9 mm³/MC; P < .001). However, micro-computed tomography surface deviation results demonstrated increased linear penetration on 32-mm glenospheres compared with 40-mm glenospheres (0.36 ± 0.03 µm vs. 0.28 ± 0.01 µm; P = .002). Surface roughness measurements showed no difference for liners; however, increased roughness was noted for 40-mm glenospheres at 5 MC compared with 32 mm (P < .05).

CONCLUSION

Larger glenospheres underwent significantly greater polyethylene volume loss and volumetric wear rates, whereas smaller glenospheres underwent greater polyethylene surface deviations. The enhanced stability provided by larger glenospheres must be weighed against the potential for increased polyethylene wear.

A Critical Review on Prosthetic Features Available for Reversed Total Shoulder Arthroplasty

Reversed total shoulder arthroplasty is a popular treatment in rotator cuff arthropathy and in displaced proximal humeral fractures in elderly. In 2016, 29 models of commercially available designs express this popularity. This study describes all the different design parameters available on the market. Prosthetic differences are found for the baseplate, glenosphere, polyethylene, and humeral component and these differences need to be weighed out carefully for each patient knowing that a gain in one mechanical parameter can balance the loss of another. Patient specific implants may help in the future.

Effect of size and dimensional tolerance of reverse total shoulder arthroplasty on wear: An in-silico study

Although huge research efforts have been devoted to wear analysis of ultra-high molecular weight polyethylene (UHMWPE) in hip and knee implants, shoulder prostheses have been studied only marginally. Recently, the authors presented a numerical wear model of reverse total shoulder arthroplasties (RTSAs), and its application for estimating the wear coefficient k from experimental data according to different wear laws. In this study, such model and k expressions are exploited to investigate the sensitivity of UHMWPE wear to implant size and dimensional tolerance. A set of 10 different geometries was analysed, considering nominal diameters in the range 36-42mm, available on the market, and a cup dimensional tolerance of +0.2, -0.0mm (resulting in a diametrical clearance ranging between 0.04-0.24mm), estimated from measurements on RTSAs. Since the most reliable wear law and wear coefficient k for UHMWPE are still controversial in the literature, both the Archard law (AR) and the wear law of UHMWPE (PE), as well as four different k expressions were considered, carrying out a total of 40 simulations. Results showed that the wear volume increases with the implant size and decreases with the dimensional tolerance for both the wear laws. Interestingly, different trends were obtained for the maximum wear depth vs. clearance: the best performing implants should have a high conformity according to the AR law but low conformity for the PE law. However, according to both laws, wear is highly affected by both implant size and dimensional tolerance, although it is much more sensitive to the latter, with up to a twofold variation of wear predicted. Indeed, dimensional tolerance directly alters the clearance, and therefore the lubrication and contact pressure distribution in the implant. Rather surprisingly the role of dimensional tolerance has been completely disregarded in the literature, as well as in the standards. Furthermore, this study notes some important issues for future work, such as the validation of wear laws and predictive wear models and the sensitivity of k to implant geometry.