In vitro validation of a self-driving aortic-turbine venous-assist device for Fontan patients

In vitro hemodynamic performance of a blood pump for self-powered venous assist in univentricular hearts

Univentricular heart anomalies represent a group of severe congenital heart defects necessitating early surgical intervention in infancy. The Fontan procedure, the final stage of single-ventricle palliation, establishes a serial connection between systemic and pulmonary circulation by channeling venous return to the lungs. The absence of the subpulmonary ventricle in this peculiar circulation progressively eventuates in failure, primarily due to chronic elevation in inferior vena cava (IVC) pressure. This study experimentally validates the effectiveness of an intracorporeally-powered venous ejector pump (VEP) in reducing IVC pressure in Fontan patients. The VEP exploits a fraction of aortic flow to create a jet-venturi effect for the IVC, negating the external power requirement and driveline infections. An invitro Fontan mock-up circulation loop is developed and the impact of VEP design parameters and physiological conditions is assessed using both idealized and patient-specific total cavopulmonary connection (TCPC) phantoms. The VEP performance in reducing IVC pressure exhibited an inverse relationship with the cardiac output and extra-cardiac conduit (ECC) size and a proportional relationship with the transpulmonary pressure gradient (TPG) and mean arterial pressure (MAP). The ideal VEP with fail-safe features provided an IVC pressure drop of 1.82 ± 0.49, 2.45 ± 0.54, and 3.12 ± 0.43 mm Hg for TPG values of 6, 8, and 10 mm Hg, respectively, averaged over all ECC sizes and cardiac outputs. Furthermore, the arterial oxygen saturation was consistently maintained above 85% during full-assist mode. These results emphasize the potential utility of the VEP to mitigate elevated venous pressure in Fontan patients.

Optimizing percutaneous pulmonary valve implantation with patient-specific 3D-printed pulmonary artery models and hemodynamic assessment

Background

Percutaneous pulmonary valve implantation (PPVI) has emerged as a less invasive alternative for treating severe pulmonary regurgitation after tetralogy of Fallot (TOF) repair in patients with a native right ventricular outflow tract (RVOT). However, the success of PPVI depends on precise patient-specific valve sizing, the avoidance of oversizing complications, and optimal valve performance. In recent years, innovative adaptations of commercially available cardiovascular mock loops have been used to test conduits in the pulmonary position. These models are instrumental in facilitating accurate pulmonic valve sizing, mitigating the risk of oversizing, and providing insight into the valve performance before implantation. This study explored the utilization of custom-modified mock loops to implant patient-specific 3D-printed pulmonary artery geometries, thereby advancing PPVI planning and execution.

Material and Methods

Patient-specific 3D-printed pulmonary artery geometries of five patients who underwent PPVI using Pulsta transcatheter heart valve (THV) ® were tested in a modified ViVitro pulse duplicator system®. Various valve sizes were subjected to 10 cycles of testing at different cardiac output levels. The transpulmonary systolic and regurgitation fractions of the valves were also recorded and compared.

Results

A total of 39 experiments were conducted using five different patient geometries and several different valve sizes (26, 28, 30, and 32 mm) at 3, 4, and 5 L/min cardiac output at heart rates of 70 beats per minute (bpm) and 60/40 systolic/diastolic ratios. The pressure gradients and regurgitation fractions of the tested valve sizes in the models were found to be similar to the pressure gradients and regurgitation fractions of valves used in real procedures. However, in two patients, different valve sizes showed better hemodynamic values than the actual implanted valves.

Discussion

The use of 3D printing technology, electromagnetic flow meters, and the custom-modified ViVitro pulse duplicator system® in conjunction with patient-specific pulmonary artery models has enabled a comprehensive assessment of percutaneous pulmonic valve implantation performance. This approach allows for accurate valve sizing, minimization of oversizing risks, and valuable insights into hemodynamic behavior before implantation. The data obtained from this experimental setup will contribute to advancing PPVI procedures and offer potential benefits in improving patient outcomes and safety.

Switching the Left and the Right Hearts: A Novel Bi-ventricle Mechanical Support Strategy with Spared Native Single-Ventricle

End-stage Fontan patients with single-ventricle (SV) circulation are often bridged-to-heart transplantation via mechanical circulatory support (MCS). Donor shortage and complexity of the SV physiology demand innovative MCS. In this paper, an out-of-the-box circulation concept, in which the left and right ventricles are switched with each other is introduced as a novel bi-ventricle MCS configuration for the "failing" Fontan patients. In the proposed configuration, the systemic circulation is maintained through a conventional mechanical ventricle assist device (VAD) while the venous circulation is delegated to the native SV. This approach spares the SV and puts it to a new use at the right-side providing the most-needed venous flow pulsatility to the failed Fontan circulation. To analyze its feasibility and performance, eight SV failure modes have been studied via an established multi-compartmental lumped parameter cardiovascular model (LPM). Here the LPM model is experimentally validated against the corresponding pulsatile mock-up flow loop measurements of a representative 15-year-old Fontan patient employing a clinically-approved VAD (Medtronic-HeartWare). The proposed surgical configuration maintained the healthy cardiac index (3-3.5 l/min/m2) and the normal mean systemic arterial pressure levels. For a failed SV with low ejection fraction (EF = 26%), representing a typical systemic Fontan failure, the proposed configuration enabled a ~ 28 mmHg amplitude in the venous/pulmonary waveforms and a 2 mmHg decrease in the central venous pressure (CVP) together with acceptable mean pulmonary artery pressures (17.5 mmHg). The pulmonary vascular resistance (PVR)-SV failure case provided a ~ 5 mmHg drop in the CVP, with venous/pulmonary pulsatility reaching to ~ 22 mmHg. For the high PVR failure case with a healthy SV (EF = 44%) pulmonary hypertension is likely to occur as expected. While this condition is routinely encountered during the heart transplantation and managed through pulmonary vasodilators a need for precise functional assessment of the spared failed-ventricle is recommended if utilized in the PVR failure mode. Comprehensive in vitro and in silico results encourage this novel concept as a low-cost, more physiological alternative to the conventional bi-ventricle MCS pending animal experiments.

Anatomical Compliance of Cavopulmonary Assist Device Designs: A Virtual Fitting Study in Fontan Patients

Several device designs for cavopulmonary mechanical circulatory support (MCS) are under investigation, however, challenged by the Fontan population's heterogeneity in size, cardiovascular and thoracic anatomy. This study aimed to preclinically assess the anatomical compliance of proposed device designs in silico. Representative double- and single-outlet cavopulmonary assist device (CPAD) designs were virtually implanted into CT imaging data of 10 patients previously palliated with total cavopulmonary connection (TCPC) for functionally univentricular hearts. Anatomical device compatibility was characterized concerning pump proximity to cardiovascular, respiratory and thoracic structures, as well as pump in- and outflow graft configuration. In 10 Fontan patients with a median age of 10.4 years (interquartile range [IQR] 5.0-15.3 years) and a median body surface area of 1.09 m2 (IQR 0.76-1.28 m2), implantation of a double-outlet CPAD was feasible in 1 patient (10%). In all other, adverse device intersection with the trachea and (neo-)aorta, or posterior pulmonary artery outflow graft kinking were observed. A single-outlet design permitted enhanced device mobilization adapting to individual anatomical conditions, resulting in device fit in nine of 10 patients (90%). Despite vast anatomical variations among single ventricle patients, a single-outlet device design may provide intracorporeal cavopulmonary MCS to a broad spectrum of failing Fontan patients.

In Silico Evaluation of a Self-powered Venous Ejector Pump for Fontan Patients

PURPOSE

The Fontan circulation carries a dismal prognosis in the long term due to its peculiar physiology and lack of a subpulmonic ventricle. Although it is multifactorial, elevated IVC pressure is accepted to be the primary cause of Fontan's high mortality and morbidity. This study presents a self-powered venous ejector pump (VEP) that can be used to lower the high IVC venous pressure in single-ventricle patients.

METHODS

A self-powered venous assist device that exploits the high-energy aortic flow to lower IVC pressure is designed. The proposed design is clinically feasible, simple in structure, and is powered intracorporeally. The device's performance in reducing IVC pressure is assessed by conducting comprehensive computational fluid dynamics simulations in idealized total cavopulmonary connections with different offsets. The device was finally applied to complex 3D reconstructed patient-specific TCPC models to validate its performance.

RESULTS

The assist device provided a significant IVC pressure drop of more than 3.2 mm Hg in both idealized and patient-specific geometries, while maintaining a high systemic oxygen saturation of more than 90%. The simulations revealed no significant caval pressure rise (< 0.1 mm Hg) and sufficient systemic oxygen saturation (> 84%) in the event of device failure, demonstrating its fail-safe feature.

CONCLUSIONS

A self-powered venous assist with promising in silico performance in improving Fontan hemodynamics is proposed. Due to its passive nature, the device has the potential to provide palliation for the growing population of patients with failing Fontan.

Narrative review of single ventricle: where are we after 40 years?

BACKGROUND AND OBJECTIVE

Key medical and surgical advances have been made in the longitudinal management of patients with "functionally" single ventricle physiology, with the principles of Fontan circulation applied to other complex congenital heart defects. The purpose of this article is to review all of the innovations, starting from fetal life, that led to a change of strategy for single ventricle.

METHODS

Our literature review included all full articles published in English language on the Cochrane, MedLine, and Embase with references to "single ventricle" and "univentricular hearts", including the initial history of the treatments for this congenital heart defects as well as the innovations reported within the last decades.

KEY CONTENT AND FINDINGS

All innovations introduced have been analyzed, including: (I) fetal diagnosis and interventions, in particular to prevent or reduce brain damages; (II) neonatal care; (III) post-natal diagnosis; (IV) interventional cardiology procedures; (V) surgical procedures, including neonatal palliations, hybrid procedures, bidirectional Glenn and variations, Fontan completion, biventricular repair; (VI) peri-operative management; (VII) Fontan failure, with Fontan take-down and conversion, and mechanical circulatory support; (VIII) transplantation, including heart, heart and lung, heart and liver; (IX) exercise; (X) pregnancy; (XI) adolescents and adults without Fontan completion; (XII) future studies, including experimental studies on animals, computational studies, genetics, stem cells and bioengineering.

CONCLUSIONS

These last 40 years have certainly changed the course of natural history for children born with any form of "functionally" single ventricle, thanks to the improvement in diagnostic and treatment techniques, and particularly to the increased knowledge of the morphology and function of these complex hearts, from fetal to adult life. There is still much left unexplored and room for improvement, and all efforts should be concentrated in collaborations among different institutions and specialties, focused on the same matter.

Computational Modeling of the Penn State Fontan Circulation Assist Device

To address the increasing number of failing Fontan patients, Penn State University and the Penn State Hershey Medical Center are developing a centrifugal blood pump for long-term mechanical support. Computational fluid dynamics (CFD) modeling of the Penn State Fontan Circulatory Assist Device (FCAD) was performed to understand hemodynamics within the pump and its potential for hemolysis and thrombosis. CFD velocity and pressure results were first validated against experimental data and found to be within the standard deviations of the velocities and within 5% of the pressures. Further simulations performed with a human blood model found that most of the fluid domain was subjected to low shear stress (<50 Pa), with areas of highest stress around the rotor blade tips that increased with pump flow rate and rotor speed (138-178 Pa). However, the stresses compared well to previous CFD studies of commercial blood pumps and remained mostly below common thresholds of hemolysis and platelet activation. Additionally, few regions of low shear rate were observed within the FCAD, signifying minimal potential for platelet adhesion. These results further emphasize the FCAD's potential that has been observed previously in experimental and animal studies.

Complications and management of functional single ventricle patients with Fontan circulation: From surgeon's point of view

Fontan surgery by step-wise completing the isolation of originally mixed pulmonary and systemic circulation provides an operative approach for functional single-ventricle patients not amenable to biventricular repair and allows their survival into adulthood. In the absence of a subpulmonic pumping chamber, however, the unphysiological Fontan circulation consequently results in diminished cardiac output and elevated central venous pressure, in which multiple short-term or long-term complications may develop. Current understanding of the Fontan-associated complications, particularly toward etiology and pathophysiology, is extremely incomplete. What's more, ongoing efforts have been made to manage these complications to weaken the Fontan-associated adverse impact and improve the life quality, but strategies are ill-defined. Herein, this review summarizes recent studies on cardiac and non-cardiac complications associated with Fontan circulation, focusing on significance or severity, etiology, pathophysiology, prevalence, risk factors, surveillance, or diagnosis. From the perspective of surgeons, we also discuss the management of the Fontan circulation based on current evidence, including post-operative administration of antithrombotic agents, ablation, pacemaker implantation, mechanical circulatory support, and final orthotopic heart transplantation, etc., to standardize diagnosis and treatment in the future.

Failures of the Fontan System in Univentricular Hearts and Mortality Risk in Heart Transplantation: A Systematic Review and Meta-Analysis

The Fontan procedure (FP) is the standard surgical treatment for Univentricular heart diseases. Over time, the Fontan system fails, leading to pathologies such as protein-losing enteropathy (PLE), plastic bronchitis (PB), and heart failure (HF). FP should be considered as a transitional step to the final treatment: heart transplantation (HT). This systematic review and meta-analysis aims to establish the risk of death following HT according to the presence of FP complications. There was a total of 691 transplanted patients in the 18 articles, immediate survival 88% (n = 448), survival from 1 to 5 years of 78% (n = 427) and survival from 5.1 to 10 years of 69% (n = 208), >10 years 61% (n = 109). The relative risk (RR) was 1.12 for PLE (95% confidence interval [CI] = 0.89-1.40, p = 0.34), 1.03 for HF (0.7-1.51, p = 0.88), 0.70 for Arrhythmias (0.39-1.24, p = 0.22), 0.46 for PB (0.08-2.72, p = 0.39), and 5.81 for CKD (1.70-19.88, p = 0.005). In patients with two or more failures, the RR was 1.94 (0.99-3.81, p = 0.05). After FP, the risk of death after HT is associated with CKD and with the presence of two or more failures.

Target Flow-Pressure Operating Range for Designing a Failing Fontan Cavopulmonary Support Device

Fontan operation as the current standard of care for the palliation of single ventricle defects results in significant late complications. Using a mechanical circulatory device for the right circulation to serve the function of the missing subpulmonary ventricle could potentially stabilize the failing Fontan circulation. This study aims to elucidate the hydraulic operating regions that should be targeted for designing cavopulmonary blood pumps. By integrating numerical analysis and available clinical information, the interaction of the cavopulmonary support via the IVC and full assist configurations with a wide range of simulated adult failing scenarios was investigated; with IVC and full assist corresponding to the inferior venous return or the entire venous return, respectively, being routed through the device. We identified the desired hydraulic operating regions for a cavopulmonary assist device by clustering all head pressures and corresponding pump flows that result in hemodynamic improvement for each simulated failing Fontan physiology. Results show that IVC support can produce beneficial hemodynamics in only a small fraction of failing Fontan scenarios. Cavopulmonary assist device could increase cardiac index by 35% and decrease the inferior vena cava pressure by 45% depending on the patient's pre-support hemodynamic state and surgical configuration of the cavopulmonary assist device (IVC or full support). The desired flow-pressure operating regions we identified can serve as the performance criteria for designing cavopulmonary assist devices as well as evaluating off-label use of commercially available left-side blood pumps for failing Fontan cavopulmonary support.

Review on Mechanical Support and Cell-Based Therapies for the Prevention and Recovery of the Failed Fontan-Kreutzer Circulation

Though the current staged surgical strategy for palliation of single ventricle heart disease, culminating in a Fontan circulation, has increased short-term survival, mounting evidence has shown that the single ventricle, especially a morphologic right ventricle (RV), is inadequate for long-term circulatory support. In addition to high rates of ventricular failure, high central venous pressures (CVP) lead to liver fibrosis or cirrhosis, lymphatic dysfunction, kidney failure, and other comorbidities. In this review, we discuss the complications seen with Fontan physiology, including causes of ventricular and multi-organ failure. We then evaluate the clinical use, results, and limitations of long-term mechanical assist devices intended to reduce RV work and high CVP, as well as biological therapies for failed Fontan circulations. Finally, we discuss experimental tissue engineering solutions designed to prevent Fontan circulation failure and evaluate knowledge gaps and needed technology development to realize a more robust single ventricle therapy.

Computational fluid dynamic simulations of a cavopulmonary assist device for failing Fontan circulation

OBJECTIVES

Adult patients who have undergone the Fontan procedure are highly vulnerable to gradual, progressive circulatory failure, and options to reverse this situation are few. A cavopulmonary assist device could decongest the venous and lymphatic systems, overcome elevated pulmonary vascular resistance, increase cardiac output, and support some of these patients to heart transplant. This study characterizes the performance and challenges of a novel multilumen cannula coupled to an external blood pump proposed as a potential Fontan cavopulmonary assist strategy.

METHODS

Computational fluid dynamic simulations were conducted for 3 extracardiac Fontan geometries consisting of 1 idealized model and 2 patient-specific models. A range of physiologic flow rates and pump assist levels were simulated to calculate the pressure gain provided by the multilumen cannula. Hemolysis index was estimated for the idealized model with Lagrangian particle tracking and 2 variations of the power-law. Wall shear stresses were also examined.

RESULTS

Pressure gains up to 4 and 9 mm Hg were achieved for the idealized and patient-specific models, respectively. Pressure gains increased with both higher cardiac output and larger pump intake through the external pump. Flow-weighted hemolysis show hemoglobin damage levels to be several times lower than the 2% threshold at the highest pump intake flow cases. Wall shear stress predictions depict elevated areas in the pulmonary vessels and regions of the cannula device.

CONCLUSIONS

The cannula tested in this study shows promise as a percutaneous option to bridge support in some patients with a failing extracardiac Fontan. Limitations identified will be addressed in future design iterations and in ongoing experimental tests.

Current spectrum, challenges and new developments in the surgical care of adults with congenital heart disease

Today, more than two thirds of patients with congenital heart disease (CHD) are adults. Cardiac surgery plays an essential role in restoring and maintaining cardiac function, aside from evolving medical treatment and catheter-based interventions. The aim of the present publication was to describe the spectrum of operations performed on adults with CHD (ACHD) by reviewing current literature. Currently, surgery for ACHD is predominantly valve surgery, since valvular pathologies are often either a part of the basic heart defect or develop as sequelae of corrective or palliative surgery. Surgical techniques for valve repair, established in patients with acquired heart disease (non-ACHD), can often be transferred to ACHD. New valve substitutes may help to reduce the number of redo operations. Most of valve operations yield good results in terms of survival and quality of life, with the precondition that the ventricular function is preserved. Heart failure due to end-stage CHD is the most frequent cause of mortality in ACHD. However, surgical treatment by means of mechanical circulatory support (MCS) is still uncommon and the mortality exceeds the one following other operations in ACHD. Currently, different devices are used and new technical developments are in progress. However, there still is no ideal assist device available. Therefore, heart transplantation remains the only valid option for end-stage CHD. Despite higher early mortality following heart transplantation in ACHD compared to non-ACHD, the long-term survival compares favorably to non-ACHD. There is room for improvement by refining the indications, the time of listing, and the perioperative care of ACHD transplant patients. Sudden death is the second most frequent cause of mortality in ACHD. Ventricular tachycardia is the most frequent cause of sudden death followed by coronary artery anomaly. Due to the increasing awareness of physicians and the improved imaging techniques, coronary artery anomalies are coming more into the focus of cardiac surgeons. However, the reported experience is limited and it is currently difficult to provide a standardized and generally applicable recommendation for the indication and the adequate surgical technique. With the increasing age and complexity of ACHD, treatment of rhythm disturbances by surgical ablation, pacemaker or implantable cardioverter defibrillator (ICD) implantation and resynchronisation gains importance. A risk score specifically designed for surgery in ACHD is among the newest developments in predicting the outcome of surgical treatment of ACHD. This evidence-based score, derived from and validated with data from the Society of Thoracic Surgeons Congenital Heart Surgery Database, enables comparison of risk-adjusted performance of the whole spectrum of procedures performed in ACHD and helps in understanding the differences in surgical outcomes. The score is thus a powerful tool for quality control and quality improvement. In conclusion, new developments in surgery for ACHD are currently made with regard to valve surgery, which comprises more than half of all operations in ACHD and in treatment of end-stage CHD, which still yields high mortality and morbidity.