Studies on interfacial and rheological properties of water soluble polymer grafted nanoparticle for application in enhanced oil recovery

Experimental Investigation of the Viscosity and Stability of Scleroglucan-Based Nanofluids for Enhanced Oil Recovery

Biopolymers emerge as promising candidates for enhanced oil recovery (EOR) applications due to their molecular structures, which exhibit better stability than polyacrylamides under harsh conditions. Nonetheless, biopolymers are susceptible to oxidation and biological degradation. Biopolymers reinforced with nanoparticles could be a potential solution to the issue. The nanofluids' stability and performance depend on the nanoparticles' properties and the preparation method. The primary objective of this study was to evaluate the effect of the preparation method and the nanoparticle type (SiO2, Al2O3, and TiO2) on the viscosity and stability of the scleroglucan (SG). The thickening effect of the SG solution was improved by adding all NPs due to the formation of three-dimensional structures between the NPs and the SG chains. The stability test showed that the SG + Al2O3 and SG + TiO2 nanofluids are highly unstable, but the SG + SiO2 nanofluids are highly stable (regardless of the preparation method). According to the ANOVA results, the preparation method and standing time influence the nanofluid viscosity with a statistical significance of 95%. On the contrary, the heating temperature and NP type are insignificant. Finally, the nanofluid with the best performance was 1000 ppm of SG + 100 ppm of SiO2_120 NPs prepared by method II.

Nanotechnology Impact on Chemical-Enhanced Oil Recovery: A Review and Bibliometric Analysis of Recent Developments

Oil and gas are only two industries that could change because of nanotechnology, a rapidly growing field. The chemical-enhanced oil recovery (CEOR) method uses chemicals to accelerate oil flow from reservoirs. New and enhanced CEOR compounds that are more efficient and eco-friendly can be created using nanotechnology. One of the main research areas is creating novel nanomaterials that can transfer EOR chemicals to the reservoir more effectively. It was creating nanoparticles that can be used to change the viscosity and surface tension of reservoir fluids and constructing nanoparticles that can be utilized to improve the efficiency of the EOR compounds that are already in use. The assessment also identifies some difficulties that must be overcome before nanotechnology-based EOR can become widely used in industry. These difficulties include the requirement for creating mass-producible, cost-effective nanomaterials. There is a need to create strategies for supplying nanomaterials to the reservoir without endangering the formation of the reservoir. The requirement is to evaluate the environmental effects of CEOR compounds based on nanotechnology. The advantages of nanotechnology-based EOR are substantial despite the difficulties. Nanotechnology could make oil production more effective, profitable, and less environmentally harmful. An extensive overview of the most current advancements in nanotechnology-based EOR is provided in this paper. It is a useful resource for researchers and business people interested in this area. This review's analysis of current advancements in nanotechnology-based EOR shows that this area is attracting more and more attention. There have been a lot more publications on this subject in recent years, and a lot of research is being done on many facets of nanotechnology-based EOR. The scientometric investigation discovered serious inadequacies in earlier studies on adopting EOR and its potential benefits for a sustainable future. Research partnerships, joint ventures, and cutting-edge technology that consider assessing current changes and advances in oil output can all benefit from the results of our scientometric analysis.

Laponite-Supported Gel Polymer Electrolyte with Multiple Lithium-Ion Transport Channels for Stable Lithium Metal Batteries

Lithium metal batteries have emerged as a promising candidate for next-generation power systems. However, the high reactivity of lithium metal with liquid electrolytes has resulted in decreased battery safety and stability, which poses a significant challenge. Herein, we present a modified laponite-supported gel polymer electrolyte (LAP@PDOL GPE) that was fabricated using in situ polymerization initiated by a redox-initiating system at ambient temperature. The LAP@PDOL GPE effectively facilitates the dissociation of lithium salts via electrostatic interaction and simultaneously constructs multiple lithium-ion transport channels within the gel polymer network. This hierarchical GPE demonstrates a remarkable ionic conductivity of 5.16 × 10^-4 S cm^-1 at 30 °C. Furthermore, the robust laponite component of the LAP@PDOL GPE forms a barrier against Li dendrite growth while also participating in the establishment of a stable electrode/electrolyte interface with Si-rich components. The in situ polymerization process further improves the interfacial contact, enabling the LiFePO₄/LAP@PDOL GPE/Li cell to exhibit an impressive capacity of 137 mAh g^-1 at 1C, with a capacity retention of 98.5% even after 400 cycles. In summary, the developed LAP@PDOL GPE shows great potential in addressing the critical issues of safety and stability associated with lithium metal batteries while also delivering improved electrochemical performance.

Mechanism and Performance Analysis of Nanoparticle-Polymer Fluid for Enhanced Oil Recovery: A Review

With the increasing energy demand, oil is still an important fuel source worldwide. The chemical flooding process is used in petroleum engineering to increase the recovery of residual oil. As a promising enhanced oil-recovery technology, polymer flooding still faces some challenges in achieving this goal. The stability of a polymer solution is easily affected by the harsh reservoir conditions of high temperature and high salt, and the influence of the external environment such as high salinity, high valence cations, pH value, temperature and its own structure is highlighted. This article also involves the introduction of commonly used nanoparticles, whose unique properties are used to improve the performance of polymers under harsh conditions. The mechanism of nanoparticle improvement on polymer properties is discussed, that is, how the interaction between them improves the viscosity, shear stability, heat-resistance and salt-tolerant performance of the polymer. Nanoparticle-polymer fluids exhibit properties that they cannot exhibit by themselves. The positive effects of nanoparticle-polymer fluids on reducing interfacial tension and improving the wettability of reservoir rock in tertiary oil recovery are introduced, and the stability of nanoparticle-polymer fluid is described. While analyzing and evaluating the research on nanoparticle-polymer fluid, indicating the obstacles and challenges that still exist at this stage, future research work on nanoparticle-polymer fluid is proposed.

Design of novel temperature-resistant and salt-tolerant acrylamide-based copolymers by aqueous dispersion polymerization

Development of polymer-based flooding technology to improve oil recovery efficiency, water dispersion copolymerization of acrylamide, cationic monomer methacryloxyethyltrimethyl ammonium chloride (METAC), and anionic monomer acrylic acid (AA) were carried out in aqueous ammonium sulfate solution with polyvinyl pyrrolidone (PVP) as the stabilizer. The copolymers were characterized by ¹H-NMR, FT-IR, TG, and SEM to confirm that they were prepared successfully and exhibited excellent salt-resistant property. Moreover, the effect of the aqueous solution of ammonium sulfate (AS) concentration, stabilizer concentration, and initiator concentration on the viscosity and size were systematically investigated. To further improve the thermal endurance properties of copolymer, hydrophobic monomers with different alkyl chain lengths were added to the above system. The acrylamide-based quadripolymer possessed prominent thermal and salt endurance properties by utilizing the advantages of zwitterionic structure and hydrophobic monomer. With the temperature rising, the viscosity retention could reach 70.2% in the water and 63.8% in the saline. This work had expected to provide a new strategy to design polymers with excellent salinity tolerance and thermal-resistance performances.

Application of Polymers for Chemical Enhanced Oil Recovery: A Review

Polymers play a significant role in enhanced oil recovery (EOR) due to their viscoelastic properties and macromolecular structure. Herein, the mechanisms of the application of polymeric materials for enhanced oil recovery are elucidated. Subsequently, the polymer types used for EOR, namely synthetic polymers and natural polymers (biopolymers), and their properties are discussed. Moreover, the numerous applications for EOR such as polymer flooding, polymer foam flooding, alkali–polymer flooding, surfactant–polymer flooding, alkali–surfactant–polymer flooding, and polymeric nanofluid flooding are appraised and evaluated. Most of the polymers exhibit pseudoplastic behavior in the presence of shear forces. The biopolymers exhibit better salt tolerance and thermal stability but are susceptible to plugging and biodegradation. As for associative synthetic polyacrylamide, several complexities are involved in unlocking its full potential. Hence, hydrolyzed polyacrylamide remains the most coveted polymer for field application of polymer floods. Finally, alkali–surfactant–polymer flooding shows good efficiency at pilot and field scales, while a recently devised polymeric nanofluid shows good potential for field application of polymer flooding for EOR.

A simulation study on hydrogel performance for enhanced oil recovery using phase-field method

Hydrogels are increasingly applied in oil recovery processes. This leads to more controlled flow of fluids in porous media. In this process, hydrogel is injected to the reservoir to block the high permeability areas. The trapped oil in low permeability regions, is then swept by water flooding. pH‐sensitive hydrogel microspheres were synthesized in another work of the authors, which effectively increased the oil recovery factor in experimental studies. In this communication, phase-field approach was used to simulate this process and to obtain the tuning parameters of the model including thickness of the contact surface (є), phase transform parameter (M₀), and excess free energy (∧). Diffusion of hydrogels was studied by Cahn–Hilliard conservative approach and the breakage, deformation, and plugging mechanisms were analyzed, based on pressure drop variations in micromodel. Moreover, Effective parameters on oil recovery factor were analyzed. Results indicated a good agreement between experimental and modeling studies of oil recovery factor in water and hydrogel flooding with absolute errors of 2.29% and 4.06%, respectively. The recovery factor was calculated using a statistical method which was in good agreement with the modeling results. The tuned parameters of the model were reported as, є = 111.7 µm, M₀ = 5 × 10⁻¹³ m³/s, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\wedge = - 0.0003$$\end{document}∧=-0.0003 J/m³.

Improving Oil Recovery of the Heterogeneous Low Permeability Reservoirs by Combination of Polymer Hydrolysis Polyacrylamide and Two Highly Biosurfactant-Producing Bacteria

Polymer hydrolysis polyacrylamide and microbes have been used to enhance oil recovery in many oil reservoirs. However, the application of this two-method combination was less investigated, especially in low permeability reservoirs. In this work, two bacteria, a rhamnolipid-producing Pseudomonas aeruginosa 8D and a lipopeptide-producing Bacillus subtilis S4, were used together with hydrolysis poly-acrylamide in a low permeability heterogeneous core physical model. The results showed that when the two bacterial fermentation liquids were used at a ratio by volumeof 1:3 (v:v), the mixture showed the optimal physicochemical properties for oil-displacement. In addition, the mixture was stable under the conditions of various temperature (20–70 °C) and salinity (0–22%). When the polymer and bacteria were mixed together, it had no significant effects in the viscosity of polymer hydrolysis polyacrylamide and the viability of bacteria. The core oil-displacement test displayed that polymer hydrolysis polyacrylamide addition followed by the bacterial mixture injection could significantly enhance oil recovery. The recovery rate was increased by 15.01% and 10.03%, respectively, compared with the sole polymer hydrolysis polyacrylamide flooding and microbial flooding. Taken together, these results suggest that the strategy of polymer hydrolysis poly-acrylamide addition followed by microbial flooding is beneficial for improving oil recovery in heterogeneous low permeability reservoirs.

A new insight into the separation of oil from oil/water emulsion by Fe3O4-SiO2 nanoparticles

Nanofluids have shown their potential in the oil recovery process through surface modification. Due to their surface characteristics, they can apply to improve the oil production from reservoirs by enabling different enhanced recovery mechanisms. The preparation and development of the Fe₃O₄@SiO₂ nanoparticles for the oil recovery process is an innovative and novel approach that influences the oil generation from reservoirs. The performance of the Fe₃O₄@SiO₂ and the other nanofluids (seawater, Fe₃O₄, and SiO₂) in the enhanced oil recovery process is assessed and compared with other flooding scenarios. The Fe₃O₄@SiO₂ NPs achieved the highest oil production rate of 90.2% while Fe₃O₄ and SiO₂ NPs achieved 70.8% and 55.3%, respectively. In contrast, the value achieved for the seawater injection was 76.5%. For the oil recovery process, the Fe₃O₄ was applied for the inhibition (i.e., decrease) of oil sedimentation, and the SiO₂ NPs were applied for wettability alteration and IFT reduction. The experimental results showed that the produced Fe₃O₄@SiO₂ NPs improved the oil recovery rates (90.2%) as well as the synergetic impact of the developed NPs by initiating several mechanisms corresponding to the use of the separate NPs in the micromodel. Moreover, the results exhibited that the reservoir conditions are a crucial function for increasing the oil recovery rates, improving the emulsion stability, and acts as a substantial step for the oil recovery method that applies this particular technique.

Artificial Neural Network to Forecast Enhanced Oil Recovery Using Hydrolyzed Polyacrylamide in Sandstone and Carbonate Reservoirs

Polymer flooding is an important enhanced oil recovery (EOR) method with high performance which is acceptable and applicable on a field scale but should first be evaluated through lab-scale experiments or simulation tools. Artificial intelligence techniques are strong simulation tools which can be used to evaluate the performance of polymer flooding operation. In this study, the main parameters of polymer flooding were selected as input parameters of models and collected from the literature, including: polymer concentration, salt concentration, rock type, initial oil saturation, porosity, permeability, pore volume flooding, temperature, API gravity, molecular weight of the polymer, and salinity. After that, multilayer perceptron (MLP), radial basis function, and fuzzy neural networks such as the adaptive neuro-fuzzy inference system were adopted to estimate the output EOR performance. The MLP neural network had a very high ability for prediction, with statistical parameters of R² = 0.9990 and RMSE = 0.0002. Therefore, the proposed model can significantly help engineers to select the proper EOR methods and API gravity, salinity, permeability, porosity, and salt concentration have the greatest impact on the polymer flooding performance.

Enhancing the Performance of HPAM Polymer Flooding Using Nano CuO/Nanoclay Blend

A single polymer flooding is a widely employed enhanced oil recovery method, despite polymer vulnerability to shear and thermal degradation. Nanohybrids, on the other hand, resist degradation and maintain superior rheological properties at different shear rates. In this article, the effect of coupling CuO nanoparticles (NPs) and nanoclay with partially hydrolyzed polyacrylamide (HPAM) polymer solution on the rheological properties and the recovery factor of the nanohybrid fluid was assessed. The results confirmed that the NP agents preserved the polymer chains from degradation under mechanical, chemical (i.e., salinity), and thermal stresses and maintained good extent of entanglement among the polymer chains, leading to a strong viscoelastic attribute, in addition to the pseudoplastic behavior. The NP additives increased the viscosity of the HPAM polymer at shear rates varying from 10–100 s−1. The rheological properties of the nanohybrid systems varied with the NP additive content, which in turn provided a window for engineering a nanohybrid system with a proper mobility ratio and scaling coefficient, while avoiding injectivity issues. Sandpack flooding tests confirmed the superior performance of the optimized nanohybrid system and showed a 39% improvement in the recovery ratio relative to the HPAM polymer injection.

Preparation and properties of amphiphilic hydrophobically associative polymer/ montmorillonite nanocomposites

In this research, a novel amphiphilic hydrophobically associative polymer nanocomposite (ADOS/OMMT) was prepared using acrylamide (AM), sodium 4-vinylbenzenesulfonate (SSS), N, N'-dimethyl octadeyl allyl ammonium bromide (DOAAB) and organo-modified montmorillonite (OMMT) through in situ polymerization. Both X-ray diffraction patterns and transmission electron microscopy images verified the dispersion morphology of OMMT in the copolymer matrix. Then, the effect of the introduction of OMMT layers on the copolymer properties was studied by comparing with pure copolymer AM/SSS/DOAAB (ADOS). The thermal degradation results demonstrated that the thermal stability of the ADOS/OMMT were better than pure copolymer ADOS. During the solution properties tests, ADOS/OMMT nanocomposite was superior to ADOS in viscosifying ability, temperature resistance, salt tolerance, shear resistance and viscoelasticity, which was because OMMT contributed to enhance the hydrophobic association structure formed between polymer molecules. Additionally, the ADOS/OMMT nanocomposite exhibited more excellent interfacial activity and crude oil emulsifiability in comparison to pure copolymer ADOS. These performances indicated ADOS/OMMT nanocomposite had good application prospects in tertiary recovery.

Preparation and solution properties of polyacrylamide-based silica nanocomposites for drag reduction application

A novel nanocomposite drag reducer showed excellent drag reduction performance by improving strength and rigidity of a polymer structure.

Role of Ionic Headgroups on the Thermal, Rheological, and Foaming Properties of Novel Betaine-Based Polyoxyethylene Zwitterionic Surfactants for Enhanced Oil Recovery

Long-term thermal stability of surfactants under harsh reservoir conditions is one of the main challenges for surfactant injection. Most of the commercially available surfactants thermally degrade or precipitate when exposed to high-temperature and high-salinity conditions. In this work, we designed and synthesized three novel betaine-based polyoxyethylene zwitterionic surfactants containing different head groups (carboxybetaine, sulfobetaine, and hydroxysulfobetaine) and bearing an unsaturated tail. The impact of the surfactant head group on the long-term thermal stability, foam stability, and surfactant–polymer interactions were examined. The thermal stability of the surfactants was assessed by monitoring the structural changes when exposed at high temperature (90 °C) for three months using 1H-NMR, 13C-NMR, and FTIR analysis. All surfactants were found thermally stable regardless of the headgroup and no structural changes were evidenced. The surfactant–polymer interactions were dominant in deionized water. However, in seawater, the surfactant addition had no effect on the rheological properties. Similarly, changing the headgroup of polyoxyethylene zwitterionic surfactants had no major effect on the foamability and foam stability. The findings of the present study reveal that the betaine-based polyoxyethylene zwitterionic surfactant can be a good choice for enhanced oil recovery application and the nature of the headgroup has no major impact on the thermal, rheological, and foaming properties of the surfactant in typical harsh reservoir conditions (high salinity, high temperature).

A review of polymer nanohybrids for oil recovery

As oil fields go into their final stage of production, new technologies are necessary to sustain production and increase the recovery of the hydrocarbon. Chemical injection is an enhanced recovery technique, which focuses on increasing the effectiveness of waterfloods. However, the use of chemical flooding has been hampered by its relatively high cost and the adsorption of the injected chemicals onto the reservoir rocks. In recent years, nanofluids have been launched as an overall less expensive and more efficient alternative to other chemical agents. Nanoparticle inclusion is also proposed to mitigate polymer flooding performance limitations under harsh reservoir conditions. This review presents a comprehensive discussion of the most recent developments of polymer nanohybrids for oil recovery. First, the preparation methods of polymer nanohybrids are summarized and explained. Then, an explanation of the different mechanisms leading to improved oil recovery are highlighted. Finally, the current challenges and opportunities for future development and application of polymer nanohybrids for chemical flooding are identified.

Feasibility Study of Applying Modified Nano-SiO2 Hyperbranched Copolymers for Enhanced Oil Recovery in Low-Mid Permeability Reservoirs

To improve oil recovery significantly in low-mid permeability reservoirs, a novel modified nano-SiO₂ hyperbranched copolymer (HPBS), consisting of polyacrylamide as hydrophilic branched chains and modified nano-SiO₂ as the core, was synthesized via an in situ free radical polymerization reaction. The structure and properties of the hyperbranched copolymer were characterized through a range of experiments, which showed that HBPS copolymers have better stability and enhanced oil recovery (EOR) capacity and also smaller hydrodynamic radius in comparison with hydrolyzed polyacrylamide (HPAM). The flooding experiments indicated that when a 1000 mg/L HPBS solution was injected, the resistance factor (RF) and residual resistance factor (RRF) increased after the injection. Following a 98% water cut after preliminary water flooding, 0.3 pore volume (PV) and 1000 mg/L HPBS solution flooding and extended water flooding (EWF) can further increase the oil recovery by 18.74% in comparison with 8.12% oil recovery when using HPAM. In this study, one can recognize that polymer flooding would be applicable in low-mid permeability reservoirs.

Role of chemical additives and their rheological properties in enhanced oil recovery

A significant amount of oil (i.e. 60–70%) remains trapped in reservoirs after the conventional primary and secondary methods of oil recovery. Enhanced oil recovery (EOR) methods are therefore necessary to recover the major fraction of unrecovered trapped oil from reservoirs to meet the present-day energy demands. The chemical EOR method is one of the promising methods where various chemical additives, such as alkalis, surfactants, polymer, and the combination of all alkali–surfactant–polymer (ASP) or surfactant–polymer (SP) solutions, are injected into the reservoir to improve the displacement and sweep efficiency. Every oil field has different conditions, which imposes new challenges toward alternative but more effective EOR techniques. Among such attractive alternative additives are polymeric surfactants, natural surfactants, nanoparticles, and self-assembled polymer systems for EOR. In this paper, water-soluble chemical additives such as alkalis, surfactants, polymer, and ASP or SP solution for chemical EOR are highlighted. This review also discusses the concepts and techniques related to the chemical methods of EOR, and highlights the rheological properties of the chemicals involved in the efficiency of EOR methods.

Effect of Sodium Oleate Surfactant Concentration Grafted onto SiO2 Nanoparticles in Polymer Flooding Processes

The nanotechnology has been applied recently to increase the efficiency of enhanced oil recovery methods. The main objective of this study is to evaluate the effect of SiO₂ nanoparticle functionalization with different loadings of sodium oleate surfactant for polymer flooding processes. The sodium oleate surfactant was synthesized using oleic acid and NaCl. The SiO₂ nanoparticles were functionalized by physical adsorption using different surfactant loadings of 2.45, 4.08, and 8.31 wt % and were characterized by thermogravimetric analyses, Fourier-transform infrared spectroscopy, dynamic light scattering, and zeta potential. Adsorption and desorption experiments of partially hydrolyzed polyacrylamide (HPAM) polymer solutions over the unmodified and surface-modified nanoparticles were performed, with higher adsorption capacity as the surfactant loading increases. The adsorption isotherms have a type III behavior, and polymer desorption from the nanoparticle surface was considered null. The effect of nanoparticles in the polymer solutions was evaluated through rheological measurements, interfacial tension (IFT) tests, contact angle measurements, capillary number, and displacement tests in a micromodel. The surface-modified SiO₂ nanoparticles showed a slight effect on the viscosity of the polymer solution and high influence on the IFT reduction and wettability alteration of the porous medium leading to an increase of the capillary number. Displacement tests showed that the oil recovery could increase up to 23 and 77% regarding polymer flooding and water flooding, respectively, by including the surface-functionalized materials.